Ldap truncating output

[Pedro Marcolino]

Hi,

I've installed the latest version of freeradius(1.0.5), and when using it with LDAP i'm having some problems.
Some output is being truncated( mainly in cisco-avpairs ):

rlm_ldap: performing search in o=radius, with filter (uid=wy09jmru)
rlm_ldap: Added password i2dhmljk in check items
rlm_ldap: looking for check items in directory...
rlm_ldap: Adding ispRadiusLoginLimit as Simultaneous-Use, value 1 & op=21
rlm_ldap: Adding ispRadiusAuthType as Auth-Type, value 1 & op=21
rlm_ldap: Adding ispRadiusPassword as User-Password, value password & op=21
rlm_ldap: Adding ispRadiusUserName as User-Name, value wy09jmru & op=21
rlm_ldap: looking for reply items in directory...
rlm_ldap: Adding ispRadiusCiscoAVPair as Cisco-AVPair, value lcp:interface-config & op=11
rlm_ldap: Adding ispRadiusCiscoAVPair as Cisco-AVPair, value lcp:interface-config & op=11
rlm_ldap: Adding ispRadiusFramedIPAddress as Framed-IP-Address, value 12.1.1.8 & op=11
rlm_ldap: Adding ispRadiusFramedProtocol as Framed-Protocol, value 1 & op=11
rlm_ldap: Adding ispRadiusServiceType as Service-Type, value 2 & op=11
rlm_ldap: user wy09jmru authorized to use remote access
rlm_ldap: ldap_release_conn: Release Id: 0
  modcall[authorize]: module "ldap" returns ok for request 2
modcall: group authorize returns ok for request 2
  rad_check_password:  Found Auth-Type 1
auth: type "LDAP"
  Processing the authenticate section of radiusd.conf
modcall: entering group Auth-Type for request 2
rlm_ldap: - authenticate
rlm_ldap: login attempt by "wy09jmru" with password "password"
rlm_ldap: user DN: uid=wy09jmru,ou=People,o=xxx.xxx,o=Radius
rlm_ldap: (re)connect to ldap:389, authentication 1
rlm_ldap: bind as uid=wy09jmru,ou=People,o=xxx.xxx,o=Radius/i2dhmljk to ldap:389
rlm_ldap: waiting for bind result ...
rlm_ldap: Bind was successful
rlm_ldap: user wy09jmru authenticated succesfully
  modcall[authenticate]: module "ldap" returns ok for request 2
modcall: group Auth-Type returns ok for request 2
  Processing the session section of radiusd.conf
modcall: entering group session for request 2
radius_xlat:  'wy09jmru at xxx.xxx'
rlm_sql (sql): sql_set_user escaped user --> 'wy09jmru at xxx.xxx'
radius_xlat:  'SELECT COUNT(*) FROM radacct WHERE UserName='wy09jmru at xxx.xxx' AND AcctStopTime = 0'
rlm_sql (sql): Reserving sql socket id: 8
rlm_sql (sql): Released sql socket id: 8
	modcall[session]: module "sql" returns ok for request 2
modcall: group session returns ok for request 2
Sending Access-Accept of id 7 to 10.16.2.10:55521
        Cisco-AVPair = "lcp:interface-config"
        Framed-IP-Address = 12.1.1.8
        Framed-Protocol = PPP
        Service-Type = Framed-User
Finished request 2
Going to the next request
--- Walking the entire request list ---
Waking up in 6 seconds...

Ldapsearch show the following:

(...)
ispRadiusCiscoAVPair: lcp:interface-config#1=ip vrf forwarding v24:xxx
ispRadiusCiscoAVPair: lcp:interface-config#2=ip unnumbered loopback14
(...)

Anyone got the same problem?
Thanks for the time.

Best Regards,
Pedro Marcolino