I am configuring wpa supplicant to use EAP-TTLS. But have few raod block. Plz help me to solve the issue. luckily i am not getting any error in RADIUS server side...
1. Getting SSL connect error.
SSL: SSL_connect:before/connect initialization
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:SSLv3 write client hello A
SSL: (where=0x1002 ret=0xffffffff)
SSL: SSL_connect:error in SSLv3 read server hello A
SSL: SSL_connect - want more data
SSL: 102 bytes pending from ssl_out
SSL: 102 bytes left to be sent out (of total 102 bytes)
EAP: method process -> ignore=FALSE methodState=MAY_CONT decision=FAIL
2. EAP entering failure state
EAP: EAP entering state FAILURE
CTRL-EVENT-EAP-FAILURE EAP authentication failed
EAPOL: SUPP_PAE entering state AUTHENTICATING
EAPOL: SUPP_BE entering state FAIL
Detail log attached below.
# ./wpa_supplicant -c ./wpa_supplicant.ttls.conf -w -ieth0 -Dmarvell
-ddd
Initializing interface 'eth0' conf './wpa_supplicant.ttls.conf' driver 'marvell' ctrl_interface 'N/A' bridge 'N/A'
Configuration file './wpa_supplicant.ttls.conf' -> '/mnt/nfs/./wpa_supplicant.ttls.conf'
Reading configuration file '/mnt/nfs/./wpa_supplicant.ttls.conf'
update_config=1
eapol_version=1
ap_scan=1
fast_reauth=1
Line: 10 - start of a new network block
ssid - hexdump_ascii(len=4):
33 43 6f 6d 3Com
scan_ssid=1 (0x1)
auth_alg: 0x1
proto: 0x1
key_mgmt: 0x9
pairwise: 0x18
group: 0x1e
eap methods - hexdump(len=16): 00 00 00 00 15 00 00 00 00 00 00 00 00 00 00 00
identity - hexdump_ascii(len=5):
6a 62 69 62 65 jbibe
anonymous_identity - hexdump_ascii(len=5):
6a 62 69 62 65 jbibe
password - hexdump_ascii(len=8): [REMOVED]
priority=2 (0x2)
phase2 - hexdump_ascii(len=8):
61 75 74 68 3d 4d 44 35 auth=MD5
Priority group 2
id=0 ssid='3Com'
Initializing interface (2) 'eth0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
IOCTL extscan: 0x8bfa, 0x0
IOCTL authalgs: 0x8bf8, 0x4
IOCTL setwpaie: 0x8be0, 0x0
IOCTL deauth: 0x8be8, 0x1
IOCTL encryptionmode: 0x8bf8, 0x5
IOCTL reasso-on: 0x8be8, 0x8
IOCTL reasso-off: 0x8be8, 0x9
ioctl[SIOCSIWPMKSA]: Invalid argument
SIOCGIWRANGE: WE(compiled)=22 WE(source)=15 enc_capa=0x0
capabilities: key_mgmt 0x0 enc 0x3
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:13:e0:9e:9b:2e
wpa_driver_marvell_set_wpa: enabled=1
IOCTL: CMD = 0x8B2A
IOCTL: CMD = 0x8B2A
IOCTL: CMD = 0x8B2A
IOCTL: CMD = 0x8B2A
wpa_driver_marvell_set_countermeasures: enabled=0
wpa_driver_marvell_set_drop_unencrypted: enabled=1
Setting scan request: 0 sec 100000 usec
Added interface eth0
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=4):
33 43 6f 6d 3Com
Trying to get current scan results first without requesting a new scan to speed up initial association
Received 117 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 2
0: 00:90:4c:91:00:01 ssid='linksys' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - SSID mismatch
No suitable AP found.
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b19 len=8
Received 401 bytes of scan results (4 BSSes)
Scan results: 4
Selecting BSS from priority group 2
0: 00:0f:cb:fe:2f:5f ssid='3Com' wpa_ie_len=24 rsn_ie_len=0 caps=0x11
selected based on WPA IE
Trying to associate with 00:0f:cb:fe:2f:5f (SSID='3Com' freq=2412 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
Overriding auth_alg selection: 0x1
Setting Auth Alg to 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 1 proto 1
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 01
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT 802.1X
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 01
No keys have been configured - skip key clearing
wpa_driver_marvell_set_drop_unencrypted: enabled=1
State: SCANNING -> ASSOCIATING
wpa_driver_marvell_associate
marvell: auto association off
IOCTL: CMD = 0x8BE0
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:0f:cb:fe:2f:5f
State: ASSOCIATING -> ASSOCIATED
Associated to a new BSS: BSSID=00:0f:cb:fe:2f:5f
No keys have been configured - skip key clearing
Associated with 00:0f:cb:fe:2f:5f
WPA: Association event - clear replay counter
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b1a len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
RX EAPOL from 00:0f:cb:fe:2f:5f
RX EAPOL - hexdump(len=9): 01 00 00 05 01 00 00 05 01
Setting authentication timeout: 70 sec 0 usec
EAPOL: Received EAP-Packet frame
EAPOL: SUPP_PAE entering state RESTART
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
EAPOL: SUPP_PAE entering state AUTHENTICATING
EAPOL: SUPP_BE entering state REQUEST
EAPOL: getSuppRsp
EAP: EAP entering state RECEIVED
EAP: Received EAP-Request id=0 method=1 vendor=0 vendorMethod=0
EAP: EAP entering state IDENTITY
CTRL-EVENT-EAP-STARTED EAP authentication started
EAP: EAP-Request Identity data - hexdump_ascii(len=0):
EAP: using anonymous identity - hexdump_ascii(len=5):
6a 62 69 62 65 jbibe
EAP: EAP entering state SEND_RESPONSE
EAP: EAP entering state IDLE
EAPOL: SUPP_BE entering state RESPONSE
EAPOL: txSuppRsp
TX EAPOL - hexdump(len=14): 01 00 00 0a 02 00 00 0a 01 6a 62 69 62 65
EAPOL: SUPP_BE entering state RECEIVE
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
EAPOL: startWhen --> 0
EAPOL: authWhile --> 0
EAPOL: SUPP_BE entering state TIMEOUT
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
EAPOL: startWhen --> 0
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
TX EAPOL - hexdump(len=4): 01 01 00 00
EAPOL: startWhen --> 0
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
TX EAPOL - hexdump(len=4): 01 01 00 00
EAPOL: idleWhile --> 0
EAP: EAP entering state FAILURE
CTRL-EVENT-EAP-FAILURE EAP authentication failed
EAPOL: SUPP_PAE entering state AUTHENTICATING
EAPOL: SUPP_BE entering state FAIL
EAPOL: SUPP_PAE entering state HELD
EAPOL: SUPP_BE entering state IDLE
Authentication with 00:0f:cb:fe:2f:5f timed out.
Added BSSID 00:0f:cb:fe:2f:5f into blacklist
State: ASSOCIATED -> DISCONNECTED
wpa_driver_marvell_disassociate
wpa_driver_marvell_mlme
marvell: auto association on
wpa_driver_marvell_set_wpa: enabled=0
IOCTL: CMD = 0x8BE0
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=4):
33 43 6f 6d 3Com
IOCTL: CMD = 0x8BFA
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b19 len=8
Received 112 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 2
0: 00:0f:cb:fe:2f:5f ssid='3Com' wpa_ie_len=24 rsn_ie_len=0 caps=0x11
selected based on WPA IE
Trying to associate with 00:0f:cb:fe:2f:5f (SSID='3Com' freq=2412 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
Overriding auth_alg selection: 0x1
Setting Auth Alg to 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 1 proto 1
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 01
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT 802.1X
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 01
No keys have been configured - skip key clearing
wpa_driver_marvell_set_drop_unencrypted: enabled=1
State: SCANNING -> ASSOCIATING
wpa_driver_marvell_associate
marvell: auto association off
IOCTL: CMD = 0x8BE0
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:0f:cb:fe:2f:5f
State: ASSOCIATING -> ASSOCIATED
Associated to a new BSS: BSSID=00:0f:cb:fe:2f:5f
No keys have been configured - skip key clearing
Associated with 00:0f:cb:fe:2f:5f
WPA: Association event - clear replay counter
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b1a len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
RX EAPOL from 00:0f:cb:fe:2f:5f
RX EAPOL - hexdump(len=9): 01 00 00 05 01 00 00 05 01
Setting authentication timeout: 70 sec 0 usec
EAPOL: Received EAP-Packet frame
EAPOL: SUPP_PAE entering state RESTART
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
EAPOL: SUPP_PAE entering state AUTHENTICATING
EAPOL: SUPP_BE entering state REQUEST
EAPOL: getSuppRsp
EAP: EAP entering state RECEIVED
EAP: Received EAP-Request id=0 method=1 vendor=0 vendorMethod=0
EAP: EAP entering state IDENTITY
CTRL-EVENT-EAP-STARTED EAP authentication started
EAP: EAP-Request Identity data - hexdump_ascii(len=0):
EAP: using anonymous identity - hexdump_ascii(len=5):
6a 62 69 62 65 jbibe
EAP: EAP entering state SEND_RESPONSE
EAP: EAP entering state IDLE
EAPOL: SUPP_BE entering state RESPONSE
EAPOL: txSuppRsp
TX EAPOL - hexdump(len=14): 01 00 00 0a 02 00 00 0a 01 6a 62 69 62 65
EAPOL: SUPP_BE entering state RECEIVE
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
EAPOL: startWhen --> 0
EAPOL: authWhile --> 0
EAPOL: SUPP_BE entering state TIMEOUT
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
EAPOL: startWhen --> 0
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
TX EAPOL - hexdump(len=4): 01 01 00 00
EAPOL: startWhen --> 0
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
TX EAPOL - hexdump(len=4): 01 01 00 00
EAPOL: heldWhile --> 0
EAPOL: idleWhile --> 0
EAP: EAP entering state FAILURE
CTRL-EVENT-EAP-FAILURE EAP authentication failed
EAPOL: SUPP_PAE entering state AUTHENTICATING
EAPOL: SUPP_BE entering state FAIL
EAPOL: SUPP_PAE entering state HELD
EAPOL: SUPP_BE entering state IDLE
Authentication with 00:0f:cb:fe:2f:5f timed out.
BSSID 00:0f:cb:fe:2f:5f blacklist count incremented to 2
State: ASSOCIATED -> DISCONNECTED
wpa_driver_marvell_disassociate
wpa_driver_marvell_mlme
marvell: auto association on
wpa_driver_marvell_set_wpa: enabled=0
IOCTL: CMD = 0x8BE0
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b19 len=8
Received 318 bytes of scan results (3 BSSes)
Scan results: 3
Selecting BSS from priority group 2
0: 00:0f:cb:fe:2f:5f ssid='3Com' wpa_ie_len=24 rsn_ie_len=0 caps=0x11
skip - blacklisted
1: 00:90:4c:91:00:01 ssid='linksys' wpa_ie_len=26 rsn_ie_len=0 caps=0x11
skip - SSID mismatch
2: 02:1b:77:00:00:77 ssid='zerom_fujitsu' wpa_ie_len=0 rsn_ie_len=0 caps=0x12
skip - no WPA/RSN IE
No APs found - clear blacklist and try again
Removed BSSID 00:0f:cb:fe:2f:5f from blacklist (clear)
Selecting BSS from priority group 2
0: 00:0f:cb:fe:2f:5f ssid='3Com' wpa_ie_len=24 rsn_ie_len=0 caps=0x11
selected based on WPA IE
Trying to associate with 00:0f:cb:fe:2f:5f (SSID='3Com' freq=2412 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
Overriding auth_alg selection: 0x1
Setting Auth Alg to 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 1 proto 1
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 01
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT 802.1X
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 01
No keys have been configured - skip key clearing
wpa_driver_marvell_set_drop_unencrypted: enabled=1
State: SCANNING -> ASSOCIATING
wpa_driver_marvell_associate
marvell: auto association off
IOCTL: CMD = 0x8BE0
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:0f:cb:fe:2f:5f
State: ASSOCIATING -> ASSOCIATED
Associated to a new BSS: BSSID=00:0f:cb:fe:2f:5f
No keys have been configured - skip key clearing
Associated with 00:0f:cb:fe:2f:5f
WPA: Association event - clear replay counter
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b1a len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
RX EAPOL from 00:0f:cb:fe:2f:5f
RX EAPOL - hexdump(len=9): 01 00 00 05 01 00 00 05 01
Setting authentication timeout: 70 sec 0 usec
EAPOL: Received EAP-Packet frame
EAPOL: SUPP_PAE entering state RESTART
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
EAPOL: SUPP_PAE entering state AUTHENTICATING
EAPOL: SUPP_BE entering state REQUEST
EAPOL: getSuppRsp
EAP: EAP entering state RECEIVED
EAP: Received EAP-Request id=0 method=1 vendor=0 vendorMethod=0
EAP: EAP entering state IDENTITY
CTRL-EVENT-EAP-STARTED EAP authentication started
EAP: EAP-Request Identity data - hexdump_ascii(len=0):
EAP: using anonymous identity - hexdump_ascii(len=5):
6a 62 69 62 65 jbibe
EAP: EAP entering state SEND_RESPONSE
EAP: EAP entering state IDLE
EAPOL: SUPP_BE entering state RESPONSE
EAPOL: txSuppRsp
TX EAPOL - hexdump(len=14): 01 00 00 0a 02 00 00 0a 01 6a 62 69 62 65
EAPOL: SUPP_BE entering state RECEIVE
RX EAPOL from 00:0f:cb:fe:2f:5f
RX EAPOL - hexdump(len=10): 01 00 00 06 01 01 00 06 15 20
EAPOL: Received EAP-Packet frame
EAPOL: SUPP_BE entering state REQUEST
EAPOL: getSuppRsp
EAP: EAP entering state RECEIVED
EAP: Received EAP-Request id=1 method=21 vendor=0 vendorMethod=0
EAP: EAP entering state GET_METHOD
EAP: Initialize selected EAP method: vendor 0 method 21 (TTLS)
EAP-TTLS: Phase2 type: EAP
EAP-TTLS: Phase2 EAP types - hexdump(len=24): 00 00 00 00 04 00 00 00 00 00 00 00 12 00 00 00 00 00 00 00 11 00 00 00
CTRL-EVENT-EAP-METHOD EAP vendor 0 method 21 (TTLS) selected
EAP: EAP entering state METHOD
SSL: Received packet(len=6) - Flags 0x20
EAP-TTLS: Start (server ver=0, own ver=0)
EAP-TTLS: Using TTLS version 0
EAP-TTLS: Start
SSL: (where=0x10 ret=0x1)
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:before/connect initialization
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:SSLv3 write client hello A
SSL: (where=0x1002 ret=0xffffffff)
SSL: SSL_connect:error in SSLv3 read server hello A
SSL: SSL_connect - want more data
SSL: 102 bytes pending from ssl_out
SSL: 102 bytes left to be sent out (of total 102 bytes)
EAP: method process -> ignore=FALSE methodState=MAY_CONT decision=FAIL
EAP: EAP entering state SEND_RESPONSE
EAP: EAP entering state IDLE
EAPOL: SUPP_BE entering state RESPONSE
EAPOL: txSuppRsp
EAPOL: txSuppRsp
TX EAPOL - hexdump(len=112): 01 00 00 6c 02 01 00 6c 15 00 16 03 01 00 61 01 00 00 5d 03 01 47 54 48 b4 c9 b4 70 d0 c0 da 18 3b 85 eb 5a a2 da 98 56 d9 34 8e 32 f4 3e f8 66 04 ab 57 f1 98 00 00 36 00 39 00 38 00 35 00 16 00 13 00 0a 00 33 00 32 00 2f 00 07 00 66 00 05 00 04 00 63 00 62 00 61 00 15 00 12 00 09 00 65 00 64 00 60 00 14 00 11 00 08 00 06 00 03 01 00
EAPOL: SUPP_BE entering state RECEIVE
RX EAPOL from 00:0f:cb:fe:2f:5f
RX EAPOL - hexdump(len=794): 01 00 03 16 01 02 03 16 15 80 00 00 03 0c 16 03 01 00 4a 02 00 00 46 03 01 47 53 ca fd ad 6c 05 88 ec 32 01 37 ea 9c eb 9a 4b ae 0e cd 9c 51 b9 a2 fe f3 96 f4 08 b1 11 a6 20 5b f9 37 60 5c b4 0c 3f 70 b3 3e dc 34 b7 04 55 6a ba c5 49 c2 40 19 8b 6d 7e 45 d5 d7 93 ca 60 00 35 00 16 03 01 02 af 0b 00 02 ab 00 02 a8 00 02 a5 30 82 02 a1 30 82 02 0a a0 03 02 01 02 02 01 02 30 0d 06 09 2a 86 48 86 f7 0d 01 01 04 05 00 30 81 89 31 0b 30 09 06 03 55 04 06 13 02 55 53 31 12 30 10 06 03 55 04 08 13 09 54 65 6e 6e 65 73 73 65 65 31 12 30 10 06 03 55 04 07 13 09 42 72 65 6e 74 77 6f 6f 64 31 0f 30 0d 06 03 55 04 0a 13 06 48 65 6c 61 76 61 31 14 30 12 06 03 55 04 0b 13 0b 45 6e 67 69 6e 65 65 72 69 6e 67 31 0c 30 0a 06 03 55 04 03 13 03 48 41 49 31 1d 30 1b 06 09 2a 86 48 86 f7 0d 01 09 01 16 0e 6f 68 62 40 63 6d 63 61 73 74 2e 6e 65 74 30 1e 17 0d 30 37 31 31 32 37 31 30 33 34 31 37 5a 17 0d 30 38 31 31 32 36 31 30 33 34 31 37 5a 30 81 89 31 0b 30 09 06 03 55 04 06 13 02 55 53 31 12 30 10 06 03 55 04 08 13 09 54 65 6e 6e 65 73 73 65 65 31 12 30 10 06 03 55 04 07 13 09 42 72 65 6e 74 77 6f 6f 64 31 0f 30 0d 06 03 55 04 0a 13 06 48 65 6c 61 76 61 31 14 30 12 06 03 55 04 0b 13 0b 45 6e 67 69 6e 65 65 72 69 6e 67 31 0c 30 0a 06 03 55 04 03 13 03 48 41 49 31 1d 30 1b 06 09 2a 86 48 86 f7 0d 01 09 01 16 0e 6f 68 62 40 63 6d 63 61 73 74 2e 6e 65 74 30 81 9f 30 0d 06 09 2a 86 48 86 f7 0d 01 01 01 05 00 03 81 8d 00 30 81 89 02 81 81 00 c6 6b f6 25 17 d8 5f 1a 2a 4d a9 9c 4b a1 3a c4 76 f3 6f 4f 00 81 55 82 81 45 6b b5 d3 93 8f ec fc f9 13 9b 9d 01 80 bd b8 89 18 b8 02 36 a8 9c c2 2b 3d ee 55 a0 92 eb 50 f0 30 d8 4d 77 2f 72 e3 e5 fa 6f bc 37 d8 a6 3d c7 df 9a 29 17 31 d7 e9 87 9e 69 8e ae ac 2e 2b b8 9f de f4 b4 73 38 42 ae 56 dd dc db fd 05 e0 d4 86 53 28 bb f2 d7 ac b8 84 da 42 1e 5d ea 11 c8 49 64 fa 59 1f db 02 03 01 00 01 a3 17 30 15 30 13 06 03 55 1d 25 04 0c 30 0a 06 08 2b 06 01 05 05 07 03 01 30 0d 06 09 2a 86 48 86 f7 0d 01 01 04 05 00 03 81 81 00 99 9d 00 ac 82 72 16 3c 53 69 bb d7 d5 50 02 ff 18 38 56 f2 35 15 e6 07 97 2c fb 7e a5 61 71 7f 9b 86 02 83 17 25 b7 2b 12 ec 04 9e 14 0a ea 62 f0 9e 99 d5 8f f5 10 ea c7 fc d7 e0 0f 84 e7 cc ba 2d 39 40 ea ee e1 d4 81 d0 13 90 ae f1 0c 28 1e 31 bb c3 eb 66 fb 01 af 66 b2 16 fb 15 56 e8 ee 6b 37 51 df 0f c6 80 8d 4f 9f ce ed d9 ec d8 52 7a 3a 0e b7 78 07 3c d4 82 2e 39 c2 02 08 39 16 03 01 00 04 0e 00 00 00
EAPOL: Received EAP-Packet frame
EAPOL: SUPP_BE entering state REQUEST
EAPOL: getSuppRsp
EAP: EAP entering state RECEIVED
EAP: Received EAP-Request id=2 method=21 vendor=0 vendorMethod=0
EAP: EAP entering state METHOD
SSL: Received packet(len=790) - Flags 0x80
SSL: TLS Message Length: 780
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:SSLv3 read server hello A
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:SSLv3 read server certificate A
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:SSLv3 read server done A
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:SSLv3 write client key exchange A
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:SSLv3 write change cipher spec A
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:SSLv3 write finished A
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:SSLv3 flush data
SSL: (where=0x1002 ret=0xffffffff)
SSL: SSL_connect:error in SSLv3 read finished A
SSL: SSL_connect - want more data
SSL: 198 bytes pending from ssl_out
SSL: 198 bytes left to be sent out (of total 198 bytes)
EAP: method process -> ignore=FALSE methodState=MAY_CONT decision=FAIL
EAP: EAP entering state SEND_RESPONSE
EAP: EAP entering state IDLE
EAPOL: SUPP_BE entering state RESPONSE
EAPOL: txSuppRsp
TX EAPOL - hexdump(len=208): 01 00 00 cc 02 02 00 cc 15 00 16 03 01 00 86 10 00 00 82 00 80 15 2b 42 91 21 e5 df 2e 62 0c a8 ac 1b 39 bd cc e0 cf b4 3d bf 69 6e 16 11 42 78 93 26 9a 7a b5 60 75 af ac 7d f3 74 8e 36 64 df 63 90 3f 7e 7b 45 5e 28 0a 0a c4 92 ae 7b c9 1a a2 16 f3 a8 20 0c d9 6d 0d 6a 7d f2 54 b1 43 ff 73 16 cc ec 7d 0d f1 23 16 d0 23 b0 da 98 61 5b f5 b7 e4 1c d0 f3 43 82 d6 aa 2e b9 e0 1c 20 c7 80 04 0d d3 1a d8 14 61 46 85 eb 1d 7b 7a 62 32 22 e3 dd 5e 38 14 03 01 00 01 01 16 03 01 00 30 35 d9 a5 85 77 0e 0b f0 8a 7e 1d d7 86 01 67 ae d0 42 40 0e a6 25 93 aa 95 a0 5c ba ca 52 4b 85 86 6b 5f c6 2c a0 49 03 33 00 be 92 3e 77 2c b9
EAPOL: SUPP_BE entering state RECEIVE
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
EAPOL: startWhen --> 0
EAPOL: authWhile --> 0
EAPOL: SUPP_BE entering state TIMEOUT
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
EAPOL: startWhen --> 0
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
TX EAPOL - hexdump(len=4): 01 01 00 00
EAPOL: startWhen --> 0
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
TX EAPOL - hexdump(len=4): 01 01 00 00
EAPOL: heldWhile --> 0
EAPOL: idleWhile --> 0
EAP: EAP entering state FAILURE
CTRL-EVENT-EAP-FAILURE EAP authentication failed
EAPOL: SUPP_PAE entering state AUTHENTICATING
EAPOL: SUPP_BE entering state FAIL
EAPOL: SUPP_PAE entering state HELD
EAPOL: SUPP_BE entering state IDLE
Authentication with 00:0f:cb:fe:2f:5f timed out.
Added BSSID 00:0f:cb:fe:2f:5f into blacklist
State: ASSOCIATED -> DISCONNECTED
wpa_driver_marvell_disassociate
wpa_driver_marvell_mlme
marvell: auto association on
wpa_driver_marvell_set_wpa: enabled=0
IOCTL: CMD = 0x8BE0
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=4):
33 43 6f 6d 3Com
IOCTL: CMD = 0x8BFA
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b19 len=8
Received 112 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 2
0: 00:0f:cb:fe:2f:5f ssid='3Com' wpa_ie_len=24 rsn_ie_len=0 caps=0x11
selected based on WPA IE
Trying to associate with 00:0f:cb:fe:2f:5f (SSID='3Com' freq=2412 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
Overriding auth_alg selection: 0x1
Setting Auth Alg to 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 1 proto 1
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 01
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT 802.1X
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 01
No keys have been configured - skip key clearing
wpa_driver_marvell_set_drop_unencrypted: enabled=1
State: SCANNING -> ASSOCIATING
wpa_driver_marvell_associate
marvell: auto association off
IOCTL: CMD = 0x8BE0
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:0f:cb:fe:2f:5f
State: ASSOCIATING -> ASSOCIATED
Associated to a new BSS: BSSID=00:0f:cb:fe:2f:5f
No keys have been configured - skip key clearing
Associated with 00:0f:cb:fe:2f:5f
WPA: Association event - clear replay counter
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: deinitialize previously used EAP method (21, TTLS) at INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b1a len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
RX EAPOL from 00:0f:cb:fe:2f:5f
RX EAPOL - hexdump(len=9): 01 00 00 05 01 00 00 05 01
Setting authentication timeout: 70 sec 0 usec
EAPOL: Received EAP-Packet frame
EAPOL: SUPP_PAE entering state RESTART
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
EAPOL: SUPP_PAE entering state AUTHENTICATING
EAPOL: SUPP_BE entering state REQUEST
EAPOL: getSuppRsp
EAP: EAP entering state RECEIVED
EAP: Received EAP-Request id=0 method=1 vendor=0 vendorMethod=0
EAP: EAP entering state IDENTITY
CTRL-EVENT-EAP-STARTED EAP authentication started
EAP: EAP-Request Identity data - hexdump_ascii(len=0):
EAP: using anonymous identity - hexdump_ascii(len=5):
6a 62 69 62 65 jbibe
EAP: EAP entering state SEND_RESPONSE
EAP: EAP entering state IDLE
EAPOL: SUPP_BE entering state RESPONSE
EAPOL: txSuppRsp
TX EAPOL - hexdump(len=14): 01 00 00 0a 02 00 00 0a 01 6a 62 69 62 65
EAPOL: SUPP_BE entering state RECEIVE
RX EAPOL from 00:0f:cb:fe:2f:5f
RX EAPOL - hexdump(len=10): 01 00 00 06 01 01 00 06 15 20
EAPOL: Received EAP-Packet frame
EAPOL: SUPP_BE entering state REQUEST
EAPOL: getSuppRsp
EAP: EAP entering state RECEIVED
EAP: Received EAP-Request id=1 method=21 vendor=0 vendorMethod=0
EAP: EAP entering state GET_METHOD
EAP: Initialize selected EAP method: vendor 0 method 21 (TTLS)
EAP-TTLS: Phase2 type: EAP
EAP-TTLS: Phase2 EAP types - hexdump(len=24): 00 00 00 00 04 00 00 00 00 00 00 00 12 00 00 00 00 00 00 00 11 00 00 00
CTRL-EVENT-EAP-METHOD EAP vendor 0 method 21 (TTLS) selected
EAP: EAP entering state METHOD
SSL: Received packet(len=6) - Flags 0x20
EAP-TTLS: Start (server ver=0, own ver=0)
EAP-TTLS: Using TTLS version 0
EAP-TTLS: Start
SSL: (where=0x10 ret=0x1)
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:before/connect initialization
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:SSLv3 write client hello A
SSL: (where=0x1002 ret=0xffffffff)
SSL: SSL_connect:error in SSLv3 read server hello A
SSL: SSL_connect - want more data
SSL: 102 bytes pending from ssl_out
SSL: 102 bytes left to be sent out (of total 102 bytes)
EAP: method process -> ignore=FALSE methodState=MAY_CONT decision=FAIL
EAP: EAP entering state SEND_RESPONSE
EAP: EAP entering state IDLE
EAPOL: SUPP_BE entering state RESPONSE
EAPOL: txSuppRsp
TX EAPOL - hexdump(len=112): 01 00 00 6c 02 01 00 6c 15 00 16 03 01 00 61 01 00 00 5d 03 01 47 54 48 fd c6 94 ab 8f 73 5c a3 e0 33 90 f6 a2 71 ac c8 5c 6f 7b 8b e7 0c ff 92 a1 e1 89 58 ca 00 00 36 00 39 00 38 00 35 00 16 00 13 00 0a 00 33 00 32 00 2f 00 07 00 66 00 05 00 04 00 63 00 62 00 61 00 15 00 12 00 09 00 65 00 64 00 60 00 14 00 11 00 08 00 06 00 03 01 00
EAPOL: SUPP_BE entering state RECEIVE
RX EAPOL from 00:0f:cb:fe:2f:5f
RX EAPOL - hexdump(len=794): 01 00 03 16 01 02 03 16 15 80 00 00 03 0c 16 03 01 00 4a 02 00 00 46 03 01 47 53 cb 46 cd de 90 f0 d2 b3 c5 a8 13 83 af d8 c0 72 1c 80 ee 62 4b 6f 1a fe 3a 09 7a b7 73 1d 20 50 4f 28 04 bb 23 f8 85 8d cb 20 b4 49 96 32 81 a5 09 c5 50 77 62 af 28 b2 9c 4f 58 4d 9b 55 52 00 35 00 16 03 01 02 af 0b 00 02 ab 00 02 a8 00 02 a5 30 82 02 a1 30 82 02 0a a0 03 02 01 02 02 01 02 30 0d 06 09 2a 86 48 86 f7 0d 01 01 04 05 00 30 81 89 31 0b 30 09 06 03 55 04 06 13 02 55 53 31 12 30 10 06 03 55 04 08 13 09 54 65 6e 6e 65 73 73 65 65 31 12 30 10 06 03 55 04 07 13 09 42 72 65 6e 74 77 6f 6f 64 31 0f 30 0d 06 03 55 04 0a 13 06 48 65 6c 61 76 61 31 14 30 12 06 03 55 04 0b 13 0b 45 6e 67 69 6e 65 65 72 69 6e 67 31 0c 30 0a 06 03 55 04 03 13 03 48 41 49 31 1d 30 1b 06 09 2a 86 48 86 f7 0d 01 09 01 16 0e 6f 68 62 40 63 6d 63 61 73 74 2e 6e 65 74 30 1e 17 0d 30 37 31 31 32 37 31 30 33 34 31 37 5a 17 0d 30 38 31 31 32 36 31 30 33 34 31 37 5a 30 81 89 31 0b 30 09 06 03 55 04 06 13 02 55 53 31 12 30 10 06 03 55 04 08 13 09 54 65 6e 6e 65 73 73 65 65 31 12 30 10 06 03 55 04 07 13 09 42 72 65 6e 74 77 6f 6f 64 31 0f 30 0d 06 03 55 04 0a 13 06 48 65 6c 61 76 61 31 14 30 12 06 03 55 04 0b 13 0b 45 6e 67 69 6e 65 65 72 69 6e 67 31 0c 30 0a 06 03 55 04 03 13 03 48 41 49 31 1d 30 1b 06 09 2a 86 48 86 f7 0d 01 09 01 16 0e 6f 68 62 40 63 6d 63 61 73 74 2e 6e 65 74 30 81 9f 30 0d 06 09 2a 86 48 86 f7 0d 01 01 01 05 00 03 81 8d 00 30 81 89 02 81 81 00 c6 6b f6 25 17 d8 5f 1a 2a 4d a9 9c 4b a1 3a c4 76 f3 6f 4f 00 81 55 82 81 45 6b b5 d3 93 8f ec fc f9 13 9b 9d 01 80 bd b8 89 18 b8 02 36 a8 9c c2 2b 3d ee 55 a0 92 eb 50 f0 30 d8 4d 77 2f 72 e3 e5 fa 6f bc 37 d8 a6 3d c7 df 9a 29 17 31 d7 e9 87 9e 69 8e ae ac 2e 2b b8 9f de f4 b4 73 38 42 ae 56 dd dc db fd 05 e0 d4 86 53 28 bb f2 d7 ac b8 84 da 42 1e 5d ea 11 c8 49 64 fa 59 1f db 02 03 01 00 01 a3 17 30 15 30 13 06 03 55 1d 25 04 0c 30 0a 06 08 2b 06 01 05 05 07 03 01 30 0d 06 09 2a 86 48 86 f7 0d 01 01 04 05 00 03 81 81 00 99 9d 00 ac 82 72 16 3c 53 69 bb d7 d5 50 02 ff 18 38 56 f2 35 15 e6 07 97 2c fb 7e a5 61 71 7f 9b 86 02 83 17 25 b7 2b 12 ec 04 9e 14 0a ea 62 f0 9e 99 d5 8f f5 10 ea c7 fc d7 e0 0f 84 e7 cc ba 2d 39 40 ea ee e1 d4 81 d0 13 90 ae f1 0c 28 1e 31 bb c3 eb 66 fb 01 af 66 b2 16 fb 15 56 e8 ee 6b 37 51 df 0f c6 80 8d 4f 9f ce ed d9 ec d8 52 7a 3a 0e b7 78 07 3c d4 82 2e 39 c2 02 08 39 16 03 01 00 04 0e 00 00 00
EAPOL: Received EAP-Packet frame
EAPOL: SUPP_BE entering state REQUEST
EAPOL: getSuppRsp
EAP: EAP entering state RECEIVED
EAP: Received EAP-Request id=2 method=21 vendor=0 vendorMethod=0
EAP: EAP entering state METHOD
SSL: Received packet(len=790) - Flags 0x80
SSL: TLS Message Length: 780
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:SSLv3 read server hello A
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:SSLv3 read server certificate A
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:SSLv3 read server done A
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:SSLv3 write client key exchange A
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:SSLv3 write change cipher spec A
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:SSLv3 write finished A
SSL: (where=0x1001 ret=0x1)
SSL: SSL_connect:SSLv3 flush data
SSL: (where=0x1002 ret=0xffffffff)
SSL: SSL_connect:error in SSLv3 read finished A
SSL: SSL_connect - want more data
SSL: 198 bytes pending from ssl_out
SSL: 198 bytes left to be sent out (of total 198 bytes)
EAP: method process -> ignore=FALSE methodState=MAY_CONT decision=FAIL
EAP: EAP entering state SEND_RESPONSE
EAP: EAP entering state IDLE
EAPOL: SUPP_BE entering state RESPONSE
EAPOL: txSuppRsp
TX EAPOL - hexdump(len=208): 01 00 00 cc 02 02 00 cc 15 00 16 03 01 00 86 10 00 00 82 00 80 9f 14 eb 33 06 03 aa 62 5e 68 5d cc 25 c5 1f 94 61 f2 20 2d d6 e0 16 a6 33 e0 0f 6d 98 80 ec 66 06 dc af 89 7a ee 14 5e 31 16 61 18 5a e6 dc 0b 52 40 4c cd 19 91 7d 8c c5 b0 36 e7 8f 9b a3 31 5c 87 b5 4c 11 35 37 bc 96 d8 44 13 7b f2 fd 60 88 f7 ec 6c 8e 21 c9 e8 ac 77 2c 57 54 26 d0 eb c0 01 de 02 27 89 26 16 bd 86 9e 26 6a a4 6d c2 07 54 48 15 21 df c3 3e 8f cf 69 0b 6b 85 d6 53 14 03 01 00 01 01 16 03 01 00 30 42 27 d6 3f 32 cf b3 97 0a be 08 b0 64 0a de 2d f1 e2 0c 96 7d b9 ee 80 d7 3d 7d 34 3b dc c7 59 ab 41 e6 27 3e fe 4b ff 52 5a 8f c1 01 a2 31 d3
EAPOL: SUPP_BE entering state RECEIVE
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
EAPOL: startWhen --> 0