Attribute "User-Password" is required for authentication

[Cody Jarrett]

Sorry, 10.1.22.10 is the ip of my 3com.

rad_recv: Access-Request packet from host 10.1.22.10:2458, id=0, length=185
         Message-Authenticator = 0xb0ba1aec817dfd6ab3fc3b0e49fb1125
         Service-Type = Framed-User
         User-Name = "cjarrett"
         Framed-MTU = 1488
         Called-Station-Id = "00-0F-CB-FC-3E-5F:CJ Test"
         Calling-Station-Id = "00-0E-35-FF-2A-82"
         NAS-Identifier = "AP11G"
         NAS-Port-Type = Wireless-802.11
         Connect-Info = "CONNECT 54Mbps 802.11g"
         EAP-Message = 0x0200000d01636a617272657474
         NAS-IP-Address = 10.1.22.10
         NAS-Port = 2
         NAS-Port-Id = "STA port # 2"
   Processing the authorize section of radiusd.conf
modcall: entering group authorize for request 0
   modcall[authorize]: module "preprocess" returns ok for request 0
   modcall[authorize]: module "chap" returns noop for request 0
   modcall[authorize]: module "mschap" returns noop for request 0
     rlm_realm: No '@' in User-Name = "cjarrett", looking up realm NULL
     rlm_realm: No such realm "NULL"
   modcall[authorize]: module "suffix" returns noop for request 0
   rlm_eap: EAP packet type response id 0 length 13
   rlm_eap: No EAP Start, assuming it's an on-going EAP conversation
   modcall[authorize]: module "eap" returns updated for request 0
     users: Matched entry DEFAULT at line 153
     users: Matched entry DEFAULT at line 177
   modcall[authorize]: module "files" returns ok for request 0
modcall: leaving group authorize (returns updated) for request 0
   rad_check_password:  Found Auth-Type pam
auth: type "PAM"
   Processing the authenticate section of radiusd.conf
modcall: entering group authenticate for request 0
rlm_pam: Attribute "User-Password" is required for authentication.
   modcall[authenticate]: module "pam" returns invalid for request 0
modcall: leaving group authenticate (returns invalid) for request 0
auth: Failed to validate the user.
Delaying request 0 for 1 seconds
Finished request 0
Going to the next request
--- Walking the entire request list ---
Waking up in 1 seconds...
--- Walking the entire request list ---
Waking up in 1 seconds...
--- Walking the entire request list ---
Sending Access-Reject of id 0 to 10.1.22.10 port 2458
Waking up in 4 seconds...



Kevin Bonner wrote:
> On Monday 18 June 2007 16:31:37 Cody Jarrett wrote:
>> I found a few topics on this issue but nothing quite informative enough.
>> I'm trying to get freeradius auth working with pam and peap. When I test
>> my config with radtest, I get Access-accept. When I use a windows XP
>> supplicant with a 3com access point, I get:
>>
>> rlm_pam: Attribute "User-Password" is required for authentication.
>> modcall[authenticate]: module "pam" returns invalid for request 4
>> modcall: leaving group authenticate (returns invalid) for request 4
>> auth: Failed to validate the user.
>>
>> Is the 3com not sending User-Password attributes in the packets, or is
>> something else wrong?
> 
> Run FreeRADIUS in debug mode (radiusd -X) to verify.  We cannot guess what 
> your NAS/client is sending.
> 
> -Kevin
> 
> 
> ------------------------------------------------------------------------
> 
> - 
> List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html