same attribute for multiple users

[Sergio Del Pino]

Thank you Ivan YOU DID IT!

but for the mailing list records this block:

DEFAULT
	Filter-Id="some_acl0.in",
	Fall-Through = 1

should go ABOVE users entry (once a user entry is checked the rest of
the file is ignored unless you put a fall through per each user) with
a "," ending the first response line, there is no need to check
against nothing in first line.

Thank you again Ivan, you drop some light to my confused mind

Best regards,

Sergio

On 9/28/07, tnt at kalik.co.yu <tnt at kalik.co.yu> wrote:
> "This way didn't work." I hope that means that DEFAULT entry didn't
> match, not that attribute didn't do anything on the NAS. DEFAULT entry
> should go below the user entries. Try using operator that always matches
> then:
>
> DEFAULT   User-Name =* "whatever"
>                  Filter-Id="some_acl0.in"
>                  Fall-Through = 1
>
> Thet should appear as a math in the debug.
>
> Ivan Kalik
> Kalik Informatika ISP
>
>
>
>
> Dana 28/9/2007, "Sergio Del Pino" <sdelp66 at gmail.com> piše:
>
> >Dear Ivan,
> >
> >Thank you for your prompt reply.
> >May be I´m not so clever as you think I´m, I've already read the users
> >file but I couldn't understand where to put the "DEFAULT" and what to
> >check.
> >I've tried to put DEFAULT in first place without any check (what
> >should I check?), after this line I put in the new line the TAB and
> >the filter attribute I need, and below this the Fall-Through = 1, This
> >way didn't work.
> >May be you are kind and can give me an additional help.
> >Thanks in advance
> >
> >Best regards,
> >
> >Sergio
> >
> >PS: I will use Cleartext-Password instead of User-Password.
> >
> >On 9/27/07, tnt at kalik.co.yu <tnt at kalik.co.yu> wrote:
> >> 1. Read instructions in users file.
> >>
> >> 2. Don't use User-Password. To find out what should you use - see 1.
> >>
> >> 3. Yes, that's what DEFAULT entries are for. To find out how - see 1.
> >>
> >> Ivan Kalik
> >> Kalik Informatika ISP
> >>
> >>
> >> Dana 27/9/2007, "Sergio Del Pino" <sdelp66 at gmail.com> pi e:
> >>
> >> >Hi, I'm a newbie on freeradius, I need to send the same attribute to
> >> >multiple users how can I do, I'm using freeradius.net 1.1.7   my users
> >> >files work this way
> >> >
> >> >user1  User-Password == "pwusr1"
> >> >user2  User-Password == "pwusr2"
> >> >....
> >> >usern  User-Password == "pwusrn"
> >> >
> >> >
> >> >the attribute I need to send is
> >> >       Filter-Id="some_acl0.in" to any user that radius send access-accept
> >> >
> >> >I want to know the config sintax in order to avoid this:
> >> >
> >> >
> >> >user1  User-Password == "pwusr1"
> >> >       Filter-Id="some_acl0.in"
> >> >user2  User-Password == "pwusr2"
> >> >       Filter-Id="some_acl0.in"
> >> >....
> >> >usern  User-Password == "pwusrn"
> >> >       Filter-Id="some_acl0.in"
> >> >
> >> >May I use the DEFAULT?
> >> >
> >> >Thanks in advance,
> >> >
> >> >Sergio
> >> >-
> >> >List info/subscribe/unsubscribe? See http://www.freeradius.org/list/usershtml
> >> >
> >> >
> >>
> >> -
> >> List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
> >>
> >
> >-
> >List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
> >
> >
>
> -
> List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
>