ttls ssl handshake error.
Sandra H.
ellbom1 at gmail.com
Thu Jan 22 17:53:33 CET 2009
Called them and they said they have numerous people utilizing their units
with freeradius and 802.1x...
Any other ideas?
Posted are my eap.conf
# -*- text -*-
##
## eap.conf -- Configuration for EAP types (PEAP, TTLS, etc.)
##
## $Id: eap.conf,v 1.24 2008/02/26 09:32:29 aland Exp $
#######################################################################
#
# Whatever you do, do NOT set 'Auth-Type := EAP'. The server
# is smart enough to figure this out on its own. The most
# common side effect of setting 'Auth-Type := EAP' is that the
# users then cannot use ANY other authentication method.
#
# EAP types NOT listed here may be supported via the "eap2" module.
# See experimental.conf for documentation.
#
eap {
# Invoke the default supported EAP type when
# EAP-Identity response is received.
#
# The incoming EAP messages DO NOT specify which EAP
# type they will be using, so it MUST be set here.
#
# For now, only one default EAP type may be used at a time.
#
# If the EAP-Type attribute is set by another module,
# then that EAP type takes precedence over the
# default type configured here.
#
default_eap_type = ttls
# A list is maintained to correlate EAP-Response
# packets with EAP-Request packets. After a
# configurable length of time, entries in the list
# expire, and are deleted.
#
timer_expire = 60
# There are many EAP types, but the server has support
# for only a limited subset. If the server receives
# a request for an EAP type it does not support, then
# it normally rejects the request. By setting this
# configuration to "yes", you can tell the server to
# instead keep processing the request. Another module
# MUST then be configured to proxy the request to
# another RADIUS server which supports that EAP type.
#
# If another module is NOT configured to handle the
# request, then the request will still end up being
# rejected.
ignore_unknown_eap_types = no
# Cisco AP1230B firmware 12.2(13)JA1 has a bug. When given
# a User-Name attribute in an Access-Accept, it copies one
# more byte than it should.
#
# We can work around it by configurably adding an extra
# zero byte.
cisco_accounting_username_bug = no
# Supported EAP-types
#
# We do NOT recommend using EAP-MD5 authentication
# for wireless connections. It is insecure, and does
# not provide for dynamic WEP keys.
#
md5 {
}
# Cisco LEAP
#
# We do not recommend using LEAP in new deployments. See:
# http://www.securiteam.com/tools/5TP012ACKE.html
#
# Cisco LEAP uses the MS-CHAP algorithm (but not
# the MS-CHAP attributes) to perform it's authentication.
#
# As a result, LEAP *requires* access to the plain-text
# User-Password, or the NT-Password attributes.
# 'System' authentication is impossible with LEAP.
#
leap {
}
# Generic Token Card.
#
# Currently, this is only permitted inside of EAP-TTLS,
# or EAP-PEAP. The module "challenges" the user with
# text, and the response from the user is taken to be
# the User-Password.
#
# Proxying the tunneled EAP-GTC session is a bad idea,
# the users password will go over the wire in plain-text,
# for anyone to see.
#
gtc {
# The default challenge, which many clients
# ignore..
#challenge = "Password: "
# The plain-text response which comes back
# is put into a User-Password attribute,
# and passed to another module for
# authentication. This allows the EAP-GTC
# response to be checked against plain-text,
# or crypt'd passwords.
#
# If you say "Local" instead of "PAP", then
# the module will look for a User-Password
# configured for the request, and do the
# authentication itself.
#
auth_type = PAP
}
## EAP-TLS
#
# See raddb/certs/README for additional comments
# on certificates.
#
# If OpenSSL was not found at the time the server was
# built, the "tls", "ttls", and "peap" sections will
# be ignored.
#
# Otherwise, when the server first starts in debugging
# mode, test certificates will be created. See the
# "make_cert_command" below for details, and the README
# file in raddb/certs
#
# These test certificates SHOULD NOT be used in a normal
# deployment. They are created only to make it easier
# to install the server, and to perform some simple
# tests with EAP-TLS, TTLS, or PEAP.
#
# See also:
#
# http:/
http://www.dslreports.com/forum/remark,9286052~mode=flat/www.dslreports.com/forum/remark,9286052~mode=flat
#
tls {
#
# These is used to simplify later configurations.
#
certdir = ${confdir}/certs
cadir = ${confdir}/certs
private_key_password = whatever
private_key_file = ${certdir}/server.pem
# If Private key & Certificate are located in
# the same file, then private_key_file &
# certificate_file must contain the same file
# name.
#
# If CA_file (below) is not used, then the
# certificate_file below MUST include not
# only the server certificate, but ALSO all
# of the CA certificates used to sign the
# server certificate.
certificate_file = ${certdir}/server.pem
# Trusted Root CA list
#
# ALL of the CA's in this list will be trusted
# to issue client certificates for authentication.
#
# In general, you should use self-signed
# certificates for 802.1x (EAP) authentication.
# In that case, this CA file should contain
# *one* CA certificate.
#
# This parameter is used only for EAP-TLS,
# when you issue client certificates. If you do
# not use client certificates, and you do not want
# to permit EAP-TLS authentication, then delete
# this configuration item.
CA_file = ${cadir}/ca.pem
#
# For DH cipher suites to work, you have to
# run OpenSSL to create the DH file first:
#
# openssl dhparam -out certs/dh 1024
#
dh_file = ${certdir}/dh
random_file = ${certdir}/random
#
# This can never exceed the size of a RADIUS
# packet (4096 bytes), and is preferably half
# that, to accomodate other attributes in
# RADIUS packet. On most APs the MAX packet
# length is configured between 1500 - 1600
# In these cases, fragment size should be
# 1024 or less.
#
# fragment_size = 1024
#
# include_length is a flag which is
# by default set to yes If set to
# yes, Total Length of the message is
# included in EVERY packet we send.
# If set to no, Total Length of the
# message is included ONLY in the
# First packet of a fragment series.
#
# include_length = yes
# Check the Certificate Revocation List
#
# 1) Copy CA certificates and CRLs to same directory.
# 2) Execute 'c_rehash <CA certs&CRLs Directory>'.
# 'c_rehash' is OpenSSL's command.
# 3) uncomment the line below.
# 5) Restart radiusd
# check_crl = yes
# CA_path = /path/to/directory/with/ca_certs/and/crls/
#
# If check_cert_issuer is set, the value will
# be checked against the DN of the issuer in
# the client certificate. If the values do not
# match, the cerficate verification will fail,
# rejecting the user.
#
# check_cert_issuer = "/C=GB/ST=Berkshire/L=Newbury/O=My
Company Ltd"
#
# If check_cert_cn is set, the value will
# be xlat'ed and checked against the CN
# in the client certificate. If the values
# do not match, the certificate verification
# will fail rejecting the user.
#
# This check is done only if the previous
# "check_cert_issuer" is not set, or if
# the check succeeds.
#
# check_cert_cn = %{User-Name}
#
# Set this option to specify the allowed
# TLS cipher suites. The format is listed
# in "man 1 ciphers".
cipher_list = "DEFAULT"
#
# This configuration entry should be deleted
# once the server is running in a normal
# configuration. It is here ONLY to make
# initial deployments easier.
#
# make_cert_command = "${certdir}/bootstrap"
}
# The TTLS module implements the EAP-TTLS protocol,
# which can be described as EAP inside of Diameter,
# inside of TLS, inside of EAP, inside of RADIUS...
#
# Surprisingly, it works quite well.
#
# The TTLS module needs the TLS module to be installed
# and configured, in order to use the TLS tunnel
# inside of the EAP packet. You will still need to
# configure the TLS module, even if you do not want
# to deploy EAP-TLS in your network. Users will not
# be able to request EAP-TLS, as it requires them to
# have a client certificate. EAP-TTLS does not
# require a client certificate.
#
# You can make TTLS require a client cert by setting
#
# EAP-TLS-Require-Client-Cert = Yes
#
# in the control items for a request.
#
ttls {
# The tunneled EAP session needs a default
# EAP type which is separate from the one for
# the non-tunneled EAP module. Inside of the
# TTLS tunnel, we recommend using EAP-MD5.
# If the request does not contain an EAP
# conversation, then this configuration ent
# is ignored.
default_eap_type = mschapv2
# The tunneled authentication request does
# not usually contain useful attributes
# like 'Calling-Station-Id', etc. These
# attributes are outside of the tunnel,
# and normally unavailable to the tunneled
# authentication request.
#
# By setting this configuration entry to
# 'yes', any attribute which NOT in the
# tunneled authentication request, but
# which IS available outside of the tunnel,
# is copied to the tunneled request.
#
# allowed values: {no, yes}
copy_request_to_tunnel = no
# The reply attributes sent to the NAS are
# usually based on the name of the user
# 'outside' of the tunnel (usually
# 'anonymous'). If you want to send the
# reply attributes based on the user name
# inside of the tunnel, then set this
# configuration entry to 'yes', and the reply
# to the NAS will be taken from the reply to
# the tunneled request.
#
# allowed values: {no, yes}
use_tunneled_reply = no
#
# The inner tunneled request can be sent
# through a virtual server constructed
# specifically for this purpose.
#
# If this entry is commented out, the inner
# tunneled request will be sent through
# the virtual server that processed the
# outer requests.
#
virtual_server = "inner-tunnel"
}
##################################################
#
# !!!!! WARNINGS for Windows compatibility !!!!!
#
##################################################
#
# If you see the server send an Access-Challenge,
# and the client never sends another Access-Request,
# then
#
# STOP!
#
# The server certificate has to have special OID's
# in it, or else the Microsoft clients will silently
# fail. See the "scripts/xpextensions" file for
# details, and the following page:
#
# http://support.microsoft.com/kb/814394/en-us
#
# For additional Windows XP SP2 issues, see:
#
# http://support.microsoft.com/kb/885453/en-us
#
# Note that we do not necessarily agree with their
# explanation... but the fix does appear to work.
#
##################################################
#
# The tunneled EAP session needs a default EAP type
# which is separate from the one for the non-tunneled
# EAP module. Inside of the TLS/PEAP tunnel, we
# recommend using EAP-MS-CHAPv2.
#
# The PEAP module needs the TLS module to be installed
# and configured, in order to use the TLS tunnel
# inside of the EAP packet. You will still need to
# configure the TLS module, even if you do not want
# to deploy EAP-TLS in your network. Users will not
# be able to request EAP-TLS, as it requires them to
# have a client certificate. EAP-PEAP does not
# require a client certificate.
#
#
# You can make TTLS require a client cert by setting
#
# EAP-TLS-Require-Client-Cert = Yes
#
# in the control items for a request.
#
peap {
# The tunneled EAP session needs a default
# EAP type which is separate from the one for
# the non-tunneled EAP module. Inside of the
# PEAP tunnel, we recommend using MS-CHAPv2,
# as that is the default type supported by
# Windows clients.
default_eap_type = mschapv2
#
# the PEAP module also has these configuration
# items, which are the same as for TTLS.
copy_request_to_tunnel = no
use_tunneled_reply = no
# When the tunneled session is proxied, the
# home server may not understand EAP-MSCHAP-V2.
# Set this entry to "no" to proxy the tunneled
# EAP-MSCHAP-V2 as normal MSCHAPv2.
# proxy_tunneled_request_as_eap = yes
#
# The inner tunneled request can be sent
# through a virtual server constructed
# specifically for this purpose.
#
# If this entry is commented out, the inner
# tunneled request will be sent through
# the virtual server that processed the
# outer requests.
#
virtual_server = "inner-tunnel"
}
#
# This takes no configuration.
#
# Note that it is the EAP MS-CHAPv2 sub-module, not
# the main 'mschap' module.
#
# Note also that in order for this sub-module to work,
# the main 'mschap' module MUST ALSO be configured.
#
# This module is the *Microsoft* implementation of MS-CHAPv2
# in EAP. There is another (incompatible) implementation
# of MS-CHAPv2 in EAP by Cisco, which FreeRADIUS does not
# currently support.
#
mschapv2 {
}
}
On Wed, Jan 21, 2009 at 5:22 PM, <tnt at kalik.net> wrote:
> >no not windows it was via a wifi CPE (ruckus cpe)
>
> ..
> >> > TLS_accept:error in SSLv3 read client certificate B
> >> >rlm_eap: SSL error error:140890C7:SSL
> >> >routines:SSL3_GET_CLIENT_CERTIFICATE:peer
> >> >did not return a certificate
>
> Call them and ask them why their supplicant didn't send the client
> certificate. There is nothing radius server can do if client doesn't
> send the certificate.
>
> Ivan Kalik
> Kalik Informatika ISP
>
> -
> List info/subscribe/unsubscribe? See
> http://www.freeradius.org/list/users.html
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.freeradius.org/pipermail/freeradius-users/attachments/20090122/6e7b5d40/attachment.html>
More information about the Freeradius-Users
mailing list