Re[2]: alvarion not receiving Filter-Id parameters
Толик Шавловский
tolik_shavlovsky at mail.ru
Sat Jan 7 16:11:12 CET 2012
hi,
i made FR auth with Exreme.
use default_eap_type = "mschapv2" instead of md5
also, i can send u my FR configs, remind me on my email on 10th of Jan.
Anatolii
07 января 2012, 18:11 от "David Peterson" <davidp at wirelessconnections.net>:
> Most of this discussion will need to go offlist as it's not appropriate for
> the list.
>
> First off, you don't need the customized radius VSA's for the Extreme
> product, only Framed-Filter-Id. Only the 4-Motion equipment requires the
> custom dictionary.
>
> Secondly you have identified two different service flows. Do all of the MSF
> and SP's actually exist in the base station? If they do are you using
> identical names? The base station is case sensitive.
>
> David
>
> -----Original Message-----
> From:
> freeradius-users-bounces+david.peterson=acc-corp.net at lists.freeradius.org
> [mailto:freeradius-users-bounces+david.peterson=acc-corp.net at lists.freeradiu
> s.org] On Behalf Of Bruce Eckstein
> Sent: Friday, January 06, 2012 5:58 PM
> To: freeradius-users at lists.freeradius.org
> Subject: alvarion not receiving Filter-Id parameters
>
> I am trying to get freeradius to authorize the services on an Alvarion
>
> BreezeMax 5000 system ver 1.7.
> I have gotten the cpe authenticated but services are not assigned.
>
> I have downloaded on 1/5/2012 the Master from git.
> I modified the dictionary file such that $INCLUDE
> dictionary.alvarion.wimax.v2_2 replaced $INCLUDE dictionary.alvarion
> $INCLUDE dictionary.wimax.alvarion replaced $INCLUDE dictionary.wimax I ran
> configure using ./configure --with-experimental-modules I ran make and make
> install (it compiled, installed and ran) wimax was uncommented in 2 places
> in default file
> one in the authorize section and one in the post-auth section
> (the wimax module indicates there should also be one in the "preacct"
> section but I do not find that one nor can I figure where it should be) and
> the following were uncommented in default file
> update request {
> WiMAX-MN-NAI = "%{User-Name}"
> }
> update reply {
> WiMAX-FA-RK-Key = 0x00
> WiMAX-MSK = "%{EAP-MSK}"
> }
> the following users were defined with these replies in the user file
> "wimax1 at WIMAX.COM" Cleartext-Password := "wimax"
> Filter-Id = "SP=sp1:MSF=msf1;SP=sp_data_eth:MSF=msf_data_eth;",
> Session-Timeout = 1200, Termination-Action = RADIUS-Request
> "KeepAliveUserNameAndPassword" Cleartext-Password :=
> "KeepAliveUserNameAndPassword"
> Filter-Id = "SP=sp1:MSF=msf1;SP=sp_data_eth:MSF=msf_data_eth;",
> Session-Timeout = 1200, Termination-Action = RADIUS-Request
>
> (I don't think I needed the keepalive one but I put it there anyways.) in
> the above filters I have tried both with and without a trailing ; after
> msf_data_eth and before the " mark no changes were made in the inner-tunnel
> file delete_mppe_keys = yes in the wimax module (I've tried with both yes
> and no)
>
> fr seems to work. I see that the Filter-Id is indicated for the reply (see
> below).
> The Alvarion CPE does get authenticated according to the CPE but there are
> no services defined for the CPE
>
> sp1, msf1, sp_data_eth, and msf_data_eth are all defined in the BTS.
> What is it that I am missing in configuration of the FreeRadius?
>
> below is a radiusd -X run
>
> FreeRADIUS Version 3.0.0, for host x86_64-unknown-linux-gnu, built on Jan 6
> 2012 at 15:07:59 Copyright (C) 1999-2009 The FreeRADIUS server project and
> contributors.
> There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A
> PARTICULAR PURPOSE.
> You may redistribute copies of FreeRADIUS under the terms of the GNU General
> Public License v2.
>
> Starting - reading configuration files ...
> including configuration file /usr/local/etc/raddb/radiusd.conf including
> configuration file /usr/local/etc/raddb/proxy.conf including configuration
> file /usr/local/etc/raddb/clients.conf including files in directory
> /usr/local/etc/raddb/modules/ including configuration file
> /usr/local/etc/raddb/modules/pam including configuration file
> /usr/local/etc/raddb/modules/wimax
> including configuration file /usr/local/etc/raddb/modules/always
> including configuration file /usr/local/etc/raddb/modules/attr_filter
> including configuration file /usr/local/etc/raddb/modules/ntlm_auth
> including configuration file /usr/local/etc/raddb/modules/attr_rewrite
> including configuration file /usr/local/etc/raddb/modules/smsotp
> including configuration file /usr/local/etc/raddb/modules/inner-eap
> including configuration file /usr/local/etc/raddb/modules/exec including
> configuration file /usr/local/etc/raddb/modules/rediswho
> including configuration file /usr/local/etc/raddb/modules/counter
> including configuration file /usr/local/etc/raddb/modules/detail
> including configuration file /usr/local/etc/raddb/modules/pap including
> configuration file /usr/local/etc/raddb/modules/mschap
> including configuration file /usr/local/etc/raddb/modules/expiration
> including configuration file /usr/local/etc/raddb/modules/krb5 including
> configuration file /usr/local/etc/raddb/modules/soh including configuration
> file /usr/local/etc/raddb/modules/preprocess
> including configuration file /usr/local/etc/raddb/modules/sqlippool
> including configuration file /usr/local/etc/raddb/sql/postgresql/ippool.conf
> including configuration file /usr/local/etc/raddb/modules/expr including
> configuration file /usr/local/etc/raddb/modules/sql including configuration
> file /usr/local/etc/raddb/sql/mysql/dialup.conf
> including configuration file /usr/local/etc/raddb/modules/ippool
> including configuration file /usr/local/etc/raddb/modules/smbpasswd
> including configuration file /usr/local/etc/raddb/modules/sradutmp
> including configuration file /usr/local/etc/raddb/modules/opendirectory
> including configuration file /usr/local/etc/raddb/modules/ldap including
> configuration file /usr/local/etc/raddb/modules/etc_group
> including configuration file /usr/local/etc/raddb/modules/eap including
> configuration file /usr/local/etc/raddb/modules/policy
> including configuration file /usr/local/etc/raddb/modules/linelog
> including configuration file /usr/local/etc/raddb/modules/radutmp
> including configuration file /usr/local/etc/raddb/modules/dynamic_clients
> including configuration file /usr/local/etc/raddb/modules/mac2vlan
> including configuration file /usr/local/etc/raddb/modules/detail.example.com
> including configuration file
> /usr/local/etc/raddb/modules/sqlcounter_expire_on_login
> including configuration file /usr/local/etc/raddb/modules/realm
> including configuration file /usr/local/etc/raddb/modules/files
> including configuration file /usr/local/etc/raddb/modules/logintime
> including configuration file /usr/local/etc/raddb/modules/cui including
> configuration file /usr/local/etc/raddb/modules/otp including configuration
> file /usr/local/etc/raddb/modules/digest
> including configuration file /usr/local/etc/raddb/modules/acct_unique
> including configuration file /usr/local/etc/raddb/modules/checkval
> including configuration file /usr/local/etc/raddb/modules/sql_log
> including configuration file /usr/local/etc/raddb/modules/perl including
> configuration file /usr/local/etc/raddb/modules/redis
> including configuration file /usr/local/etc/raddb/modules/replicate
> including configuration file /usr/local/etc/raddb/modules/chap including
> configuration file /usr/local/etc/raddb/modules/echo including configuration
> file /usr/local/etc/raddb/modules/unix including configuration file
> /usr/local/etc/raddb/modules/utf8 including configuration file
> /usr/local/etc/raddb/modules/passwd
> including configuration file /usr/local/etc/raddb/modules/detail.log
> including configuration file /usr/local/etc/raddb/modules/mac2ip
> including configuration file /usr/local/etc/raddb/policy.conf including
> files in directory /usr/local/etc/raddb/sites-enabled/
> including configuration file /usr/local/etc/raddb/sites-enabled/default
> including configuration file
> /usr/local/etc/raddb/sites-enabled/control-socket
> including configuration file /usr/local/etc/raddb/sites-enabled/inner-tunnel
> main {
> security {
> allow_core_dumps = no
> }
> }
> including dictionary file /usr/local/etc/raddb/dictionary main {
> name = "radiusd"
> prefix = "/usr/local"
> localstatedir = "/usr/local/var"
> sbindir = "/usr/local/sbin"
> logdir = "/usr/local/var/log/radius"
> run_dir = "/usr/local/var/run/radiusd"
> libdir = "/usr/local/lib"
> radacctdir = "/usr/local/var/log/radius/radacct"
> hostname_lookups = no
> max_request_time = 30
> cleanup_delay = 5
> max_requests = 1024
> pidfile = "/usr/local/var/run/radiusd/radiusd.pid"
> checkrad = "/usr/local/sbin/checkrad"
> debug_level = 0
> proxy_requests = yes
> log {
> stripped_names = no
> auth = no
> auth_badpass = no
> auth_goodpass = no
> }
> security {
> max_attributes = 200
> reject_delay = 1
> status_server = yes
> }
> }
> radiusd: #### Loading Realms and Home Servers ####
> proxy server {
> retry_delay = 5
> retry_count = 3
> default_fallback = no
> dead_time = 120
> wake_all_if_all_dead = no
> }
> home_server localhost {
> ipaddr = 127.0.0.1
> port = 1812
> type = "auth"
> secret = "testing123"
> response_window = 20
> max_outstanding = 65536
> require_message_authenticator = yes
> zombie_period = 40
> status_check = "status-server"
> ping_interval = 30
> check_interval = 30
> num_answers_to_alive = 3
> num_pings_to_alive = 3
> revive_interval = 120
> status_check_timeout = 4
> coa {
> irt = 2
> mrt = 16
> mrc = 5
> mrd = 30
> }
> limit {
> max_connections = 16
> max_requests = 0
> lifetime = 0
> idle_timeout = 0
> }
> }
> home_server_pool my_auth_failover {
> type = fail-over
> home_server = localhost
> }
> realm example.com {
> auth_pool = my_auth_failover
> }
> realm LOCAL {
> }
> radiusd: #### Loading Clients ####
> client localhost {
> ipaddr = 127.0.0.1
> require_message_authenticator = no
> secret = "testing123"
> nastype = "other"
> proto = "*"
> max_connections = 16
> }
> client 10.97.0.0/24 {
> require_message_authenticator = no
> secret = "testing123"
> shortname = "private-network-1"
> max_connections = 16
> }
> radiusd: #### Instantiating modules ####
> instantiate {
> Module: Linked to module rlm_exec
> Module: Instantiating module "exec" from file
> /usr/local/etc/raddb/modules/exec
> exec {
> wait = no
> input_pairs = "request"
> shell_escape = yes
> }
> Module: Linked to module rlm_expr
> Module: Instantiating module "expr" from file
> /usr/local/etc/raddb/modules/expr
> Module: Linked to module rlm_expiration
> Module: Instantiating module "expiration" from file
> /usr/local/etc/raddb/modules/expiration
> expiration {
> reply-message = "Password Has Expired "
> }
> Module: Linked to module rlm_logintime
> Module: Instantiating module "logintime" from file
> /usr/local/etc/raddb/modules/logintime
> logintime {
> reply-message = "You are calling outside your allowed timespan "
> minimum-timeout = 60
> }
> }
> radiusd: #### Loading Virtual Servers #### server { # from file
> /usr/local/etc/raddb/radiusd.conf
> modules {
> Module: Creating Auth-Type = digest
> Module: Checking authenticate {...} for more modules to load
> Module: Linked to module rlm_pap
> Module: Instantiating module "pap" from file
> /usr/local/etc/raddb/modules/pap
> pap {
> encryption_scheme = "auto"
> auto_header = no
> }
> Module: Linked to module rlm_chap
> Module: Instantiating module "chap" from file
> /usr/local/etc/raddb/modules/chap
> Module: Linked to module rlm_mschap
> Module: Instantiating module "mschap" from file
> /usr/local/etc/raddb/modules/mschap
> mschap {
> use_mppe = yes
> require_encryption = no
> require_strong = no
> with_ntdomain_hack = no
> passchange {
> }
> allow_retry = yes
> }
> Module: Linked to module rlm_digest
> Module: Instantiating module "digest" from file
> /usr/local/etc/raddb/modules/digest
> Module: Linked to module rlm_unix
> Module: Instantiating module "unix" from file
> /usr/local/etc/raddb/modules/unix
> unix {
> radwtmp = "/usr/local/var/log/radius/radwtmp"
> }
> Module: Linked to module rlm_eap
> Module: Instantiating module "eap" from file
> /usr/local/etc/raddb/modules/eap
> eap {
> default_eap_type = "md5"
> timer_expire = 60
> ignore_unknown_eap_types = no
> cisco_accounting_username_bug = no
> max_sessions = 4096
> }
> Module: Linked to sub-module rlm_eap_md5
> Module: Instantiating eap-md5
> Module: Linked to sub-module rlm_eap_leap
> Module: Instantiating eap-leap
> Module: Linked to sub-module rlm_eap_gtc
> Module: Instantiating eap-gtc
> gtc {
> challenge = "Password: "
> auth_type = "PAP"
> }
> Module: Linked to sub-module rlm_eap_tls
> Module: Instantiating eap-tls
> tls {
> rsa_key_exchange = no
> dh_key_exchange = yes
> rsa_key_length = 512
> dh_key_length = 512
> verify_depth = 0
> CA_path = "/usr/local/etc/raddb/certs"
> pem_file_type = yes
> private_key_file = "/usr/local/etc/raddb/certs/server.pem"
> certificate_file = "/usr/local/etc/raddb/certs/server.pem"
> CA_file = "/usr/local/etc/raddb/certs/ca.pem"
> private_key_password = "whatever"
> dh_file = "/usr/local/etc/raddb/certs/dh"
> random_file = "/usr/local/etc/raddb/certs/random"
> fragment_size = 1024
> include_length = yes
> check_crl = no
> cipher_list = "DEFAULT"
> make_cert_command = "/usr/local/etc/raddb/certs/bootstrap"
> cache {
> enable = no
> lifetime = 24
> max_entries = 255
> }
> verify {
> }
> ocsp {
> enable = no
> override_cert_url = yes
> url = "http://127.0.0.1/ocsp/"
> }
> }
> Module: Linked to sub-module rlm_eap_ttls
> Module: Instantiating eap-ttls
> ttls {
> default_eap_type = "md5"
> copy_request_to_tunnel = no
> use_tunneled_reply = no
> virtual_server = "inner-tunnel"
> include_length = yes
> }
> Module: Linked to sub-module rlm_eap_peap
> Module: Instantiating eap-peap
> peap {
> default_eap_type = "mschapv2"
> copy_request_to_tunnel = no
> use_tunneled_reply = no
> proxy_tunneled_request_as_eap = yes
> virtual_server = "inner-tunnel"
> soh = no
> }
> Module: Linked to sub-module rlm_eap_mschapv2
> Module: Instantiating eap-mschapv2
> mschapv2 {
> with_ntdomain_hack = no
> send_error = no
> }
> Module: Checking authorize {...} for more modules to load
> Module: Linked to module rlm_preprocess
> Module: Instantiating module "preprocess" from file
> /usr/local/etc/raddb/modules/preprocess
> preprocess {
> huntgroups = "/usr/local/etc/raddb/huntgroups"
> hints = "/usr/local/etc/raddb/hints"
> with_ascend_hack = no
> ascend_channels_per_line = 23
> with_ntdomain_hack = no
> with_specialix_jetstream_hack = no
> with_cisco_vsa_hack = no
> with_alvarion_vsa_hack = no
> }
> Module: Linked to module rlm_wimax
> Module: Instantiating module "wimax" from file
> /usr/local/etc/raddb/modules/wimax
> wimax {
> delete_mppe_keys = yes
> }
> Module: Linked to module rlm_realm
> Module: Instantiating module "suffix" from file
> /usr/local/etc/raddb/modules/realm
> realm suffix {
> format = "suffix"
> delimiter = "@"
> ignore_default = no
> ignore_null = no
> }
> Module: Linked to module rlm_files
> Module: Instantiating module "files" from file
> /usr/local/etc/raddb/modules/files
> files {
> usersfile = "/usr/local/etc/raddb/users"
> acctusersfile = "/usr/local/etc/raddb/acct_users"
> preproxy_usersfile = "/usr/local/etc/raddb/preproxy_users"
> compat = "no"
> }
> Module: Checking preacct {...} for more modules to load
> Module: Loading virtual module acct_unique
> Module: Checking accounting {...} for more modules to load
> Module: Linked to module rlm_detail
> Module: Instantiating module "detail" from file
> /usr/local/etc/raddb/modules/detail
> detail {
> detailfile =
> "/usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-
> IPv6-Address}}/detail-%Y%m%d"
> header = "%t"
> detailperm = 384
> dirperm = 493
> locking = no
> log_packet_header = no
> }
> Module: Linked to module rlm_radutmp
> Module: Instantiating module "radutmp" from file
> /usr/local/etc/raddb/modules/radutmp
> radutmp {
> filename = "/usr/local/var/log/radius/radutmp"
> username = "%{User-Name}"
> case_sensitive = yes
> check_with_nas = yes
> perm = 384
> callerid = yes
> }
> Module: Linked to module rlm_attr_filter
> Module: Instantiating module "attr_filter.accounting_response" from file
> /usr/local/etc/raddb/modules/attr_filter
> attr_filter attr_filter.accounting_response {
> attrsfile = "/usr/local/etc/raddb/attrs.accounting_response"
> key = "%{User-Name}"
> relaxed = no
> }
> Module: Checking session {...} for more modules to load
> Module: Checking post-proxy {...} for more modules to load
> Module: Checking post-auth {...} for more modules to load
> Module: Loading virtual module remove_reply_message_if_eap
> Module: Linked to module rlm_always
> Module: Instantiating module "noop" from file
> /usr/local/etc/raddb/modules/always
> always noop {
> rcode = "noop"
> simulcount = 0
> mpp = no
> }
> Module: Instantiating module "attr_filter.access_reject" from file
> /usr/local/etc/raddb/modules/attr_filter
> attr_filter attr_filter.access_reject {
> attrsfile = "/usr/local/etc/raddb/attrs.access_reject"
> key = "%{User-Name}"
> relaxed = no
> }
> Module: Loading virtual module remove_reply_message_if_eap
> } # modules
> } # server
> server inner-tunnel { # from file
> /usr/local/etc/raddb/sites-enabled/inner-tunnel
> modules {
> Module: Checking authenticate {...} for more modules to load
> Module: Checking authorize {...} for more modules to load
> Module: Checking session {...} for more modules to load
> Module: Checking post-proxy {...} for more modules to load
> Module: Checking post-auth {...} for more modules to load
> } # modules
> } # server
> radiusd: #### Opening IP addresses and Ports #### listen {
> type = "auth"
> ipaddr = *
> port = 0
> }
> listen {
> type = "acct"
> ipaddr = *
> port = 0
> }
> listen {
> type = "control"
> listen {
> socket = "/usr/local/var/run/radiusd/radiusd.sock"
> }
> }
> listen {
> type = "auth"
> ipaddr = 127.0.0.1
> port = 18120
> }
> Listening on authentication address * port 1812 Listening on accounting
> address * port 1813 Listening on command file
> /usr/local/var/run/radiusd/radiusd.sock
> Listening on authentication address 127.0.0.1 port 18120 as server
> inner-tunnel Opening new proxy address * port 1814 Listening on proxy
> address * port 1814 Ready to process requests.
> rad_recv: Access-Request packet from host 10.97.0.51 port 49154, id=252,
> length=181
> User-Name = "KeepAliveUserNameAndPassword"
> NAS-IP-Address = 10.97.0.51
> NAS-Port-Type = Wireless-802.16
> NAS-Port = 0
> Calling-Station-Id = "\000\000\000\000\000"
> NAS-Identifier = "001001003000096000"
> WiMAX-GMT-Timezone-offset = 0
> Message-Authenticator = 0x07dfa70c37088f55baade217a16d54fc
> Acct-Session-Id = "KeepAliveSessionId"
> User-Password = "KeepAliveUserNameAndPassword"
> (0) # Executing section authorize from file
> /usr/local/etc/raddb/sites-enabled/default
> (0) group authorize {
> (0) - entering group authorize {...}
> (0) [preprocess] = ok
> (0) [chap] = noop
> (0) [mschap] = noop
> (0) [digest] = noop
> rlm_wimax: Fixing WiMAX binary Calling-Station-Id to 00-00-00-00-00-00
> (0) [wimax] = ok
> (0) suffix : No '@' in User-Name = "KeepAliveUserNameAndPassword", looking
> up realm NULL
> (0) suffix : No such realm "NULL"
> (0) [suffix] = noop
> (0) eap : No EAP-Message, not doing EAP
> (0) [eap] = noop
> (0) files : users: Matched entry KeepAliveUserNameAndPassword at line 7
> (0) [files] = ok
> (0) [expiration] = noop
> (0) [logintime] = noop
> (0) [pap] = updated
> (0) Found Auth-Type = PAP
> (0) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
> (0) group PAP {
> (0) - entering group PAP {...}
> (0) pap : login attempt with password "KeepAliveUserNameAndPassword"
> (0) pap : Using clear text password "KeepAliveUserNameAndPassword"
> (0) pap : User authenticated successfully
> (0) [pap] = ok
> (0) # Executing section post-auth from file
> /usr/local/etc/raddb/sites-enabled/default
> (0) group post-auth {
> (0) - entering group post-auth {...}
> (0) [exec] = noop
> (0) update request {
> (0) expand: %{User-Name} -> KeepAliveUserNameAndPassword
> (0) } # update request = noop
> (0) update reply {
> (0) expand: %{EAP-MSK} ->
> (0) } # update reply = noop
> (0) wimax : No EAP-MSK or EAP-EMSK. Cannot create WiMAX keys.
> (0) [wimax] = noop
> (0) policy remove_reply_message_if_eap {
> (0) - entering policy remove_reply_message_if_eap {...}
> (0) ? if (reply:EAP-Message&& reply:Reply-Message)
> (0) ? Evaluating (reply:EAP-Message ) -> FALSE
> (0) ? Skipping (reply:Reply-Message)
> (0) ? if (reply:EAP-Message&& reply:Reply-Message) -> FALSE
> (0) else else {
> (0) - entering else else {...}
> (0) [noop] = noop
> (0) - else else returns noop
> (0) - policy remove_reply_message_if_eap returns noop
> Sending Access-Accept of id 252 to 10.97.0.51 port 49154
> Filter-Id = "SP=sp1:MSF=msf1;SP=sp_data_eth:MSF=msf_data_eth;"
> Session-Timeout = 1200
> Termination-Action = RADIUS-Request
> WiMAX-FA-RK-Key = 0x00
> WiMAX-MSK = 0x
> WARNING: Skipping zero-length attribute WiMAX-MSK
> (0) Finished request 0.
> Waking up in 0.3 seconds.
> Waking up in 4.6 seconds.
> (0) Cleaning up request packet ID 252 with timestamp +1 Ready to process
> requests.
> rad_recv: Access-Request packet from host 10.97.0.51 port 49154, id=253,
> length=258
> User-Name = "{am=1}8ea39298d98b6189e0aad92594970151 at WIMAX.COM"
> NAS-IP-Address = 10.97.0.51
> NAS-Port-Type = Wireless-802.16
> NAS-Port = 1
> Calling-Station-Id = "\000\020\347a\r\226"
> NAS-Identifier = "001001003000096000"
> WiMAX-GMT-Timezone-offset = 0
> Framed-MTU = 1490
> Service-Type = Framed-User
> WiMAX-Release = "1.0"
> WiMAX-Accounting-Capabilities = IP-Session-Based
> WiMAX-BS-Id = 0x303031303031303033303030303936303030
> EAP-Message =
> 0x02010035017b616d3d317d3865613339323938643938623631383965306161643932353934
> 3937303135314057494d41582e434f4d
> Message-Authenticator = 0x6a08e376952afbaf0740a456767bfe80
> (1) # Executing section authorize from file
> /usr/local/etc/raddb/sites-enabled/default
> (1) group authorize {
> (1) - entering group authorize {...}
> (1) [preprocess] = ok
> (1) [chap] = noop
> (1) [mschap] = noop
> (1) [digest] = noop
> rlm_wimax: Fixing WiMAX binary Calling-Station-Id to 00-10-e7-61-0d-96
> (1) [wimax] = ok
> (1) suffix : Looking up realm "WIMAX.COM" for User-Name =
> "{am=1}8ea39298d98b6189e0aad92594970151 at WIMAX.COM"
> (1) suffix : No such realm "WIMAX.COM"
> (1) [suffix] = noop
> (1) eap : EAP packet type response id 1 length 53
> (1) eap : EAP-Identity reply, returning 'ok' so we can short-circuit the
> rest of authorize
> (1) [eap] = ok
> (1) Found Auth-Type = EAP
> (1) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
> (1) group authenticate {
> (1) - entering group authenticate {...}
> (1) eap : EAP Identity
> (1) eap : processing type md5
> rlm_eap_md5: Issuing Challenge
> (1) [eap] = handled
> Sending Access-Challenge of id 253 to 10.97.0.51 port 49154
> EAP-Message = 0x010200160410d780646d179a777255c505dfbee44ab4
> Message-Authenticator = 0x00000000000000000000000000000000
> State = 0xee37a64fee35a255d3718fb2df57c86c
> (1) Finished request 1.
> Waking up in 0.3 seconds.
> rad_recv: Access-Request packet from host 10.97.0.51 port 49154, id=254,
> length=229
> User-Name = "{am=1}8ea39298d98b6189e0aad92594970151 at WIMAX.COM"
> NAS-IP-Address = 10.97.0.51
> NAS-Port-Type = Wireless-802.16
> NAS-Port = 1
> Calling-Station-Id = "\000\020\347a\r\226"
> NAS-Identifier = "001001003000096000"
> WiMAX-GMT-Timezone-offset = 0
> Framed-MTU = 1490
> Service-Type = Framed-User
> State = 0xee37a64fee35a255d3718fb2df57c86c
> WiMAX-Release = "1.0"
> WiMAX-Accounting-Capabilities = IP-Session-Based
> WiMAX-BS-Id = 0x303031303031303033303030303936303030
> EAP-Message = 0x020200060315
> Message-Authenticator = 0x94447e93f95cc98a8a6c227ccd901efe
> (2) # Executing section authorize from file
> /usr/local/etc/raddb/sites-enabled/default
> (2) group authorize {
> (2) - entering group authorize {...}
> (2) [preprocess] = ok
> (2) [chap] = noop
> (2) [mschap] = noop
> (2) [digest] = noop
> rlm_wimax: Fixing WiMAX binary Calling-Station-Id to 00-10-e7-61-0d-96
> (2) [wimax] = ok
> (2) suffix : Looking up realm "WIMAX.COM" for User-Name =
> "{am=1}8ea39298d98b6189e0aad92594970151 at WIMAX.COM"
> (2) suffix : No such realm "WIMAX.COM"
> (2) [suffix] = noop
> (2) eap : EAP packet type response id 2 length 6
> (2) eap : No EAP Start, assuming it's an on-going EAP conversation
> (2) [eap] = updated
> (2) [files] = noop
> (2) [expiration] = noop
> (2) [logintime] = noop
> (2) pap : WARNING! No "known good" password found for the user.
> Authentication may fail because of this.
> (2) [pap] = noop
> (2) Found Auth-Type = EAP
> (2) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
> (2) group authenticate {
> (2) - entering group authenticate {...}
> (2) eap : Request found, released from the list
> (2) eap : EAP NAK
> (2) eap : EAP-NAK asked for EAP-Type/ttls
> (2) eap : processing type tls
> (2) tls : Initiate
> (2) tls : Start returned 1
> (2) [eap] = handled
> Sending Access-Challenge of id 254 to 10.97.0.51 port 49154
> EAP-Message = 0x010300061520
> Message-Authenticator = 0x00000000000000000000000000000000
> State = 0xee37a64fef34b355d3718fb2df57c86c
> (2) Finished request 2.
> Waking up in 0.1 seconds.
> rad_recv: Access-Request packet from host 10.97.0.51 port 49154, id=255,
> length=285
> User-Name = "{am=1}8ea39298d98b6189e0aad92594970151 at WIMAX.COM"
> NAS-IP-Address = 10.97.0.51
> NAS-Port-Type = Wireless-802.16
> NAS-Port = 1
> Calling-Station-Id = "\000\020\347a\r\226"
> NAS-Identifier = "001001003000096000"
> WiMAX-GMT-Timezone-offset = 0
> Framed-MTU = 1490
> Service-Type = Framed-User
> State = 0xee37a64fef34b355d3718fb2df57c86c
> WiMAX-Release = "1.0"
> WiMAX-Accounting-Capabilities = IP-Session-Based
> WiMAX-BS-Id = 0x303031303031303033303030303936303030
> EAP-Message =
> 0x0203003e150016030100330100002f0301000006dea50c9829a6d3f565bcdf7456521cc609
> 9d8b828e302b1e2dce4a70e7000008002f000a000500040100
> Message-Authenticator = 0xd86dddc0e2ef35284fb32302bf1daedf
> (3) # Executing section authorize from file
> /usr/local/etc/raddb/sites-enabled/default
> (3) group authorize {
> (3) - entering group authorize {...}
> (3) [preprocess] = ok
> (3) [chap] = noop
> (3) [mschap] = noop
> (3) [digest] = noop
> rlm_wimax: Fixing WiMAX binary Calling-Station-Id to 00-10-e7-61-0d-96
> (3) [wimax] = ok
> (3) suffix : Looking up realm "WIMAX.COM" for User-Name =
> "{am=1}8ea39298d98b6189e0aad92594970151 at WIMAX.COM"
> (3) suffix : No such realm "WIMAX.COM"
> (3) [suffix] = noop
> (3) eap : EAP packet type response id 3 length 62
> (3) eap : Continuing tunnel setup.
> (3) [eap] = ok
> (3) Found Auth-Type = EAP
> (3) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
> (3) group authenticate {
> (3) - entering group authenticate {...}
> (3) eap : Request found, released from the list
> (3) eap : EAP/ttls
> (3) eap : processing type ttls
> (3) ttls : Authenticate
> (3) ttls : processing EAP-TLS
> (3) ttls : eaptls_verify returned 7
> (3) ttls : Done initial handshake
> (3) ttls : (other): before/accept initialization
> (3) ttls : TLS_accept: before/accept initialization
> (3) ttls :<<< TLS 1.0 Handshake [length 0033], ClientHello
> (3) ttls : TLS_accept: SSLv3 read client hello A
> (3) ttls :>>> TLS 1.0 Handshake [length 002a], ServerHello
> (3) ttls : TLS_accept: SSLv3 write server hello A
> (3) ttls :>>> TLS 1.0 Handshake [length 085e], Certificate
> (3) ttls : TLS_accept: SSLv3 write certificate A
> (3) ttls :>>> TLS 1.0 Handshake [length 0004], ServerHelloDone
> (3) ttls : TLS_accept: SSLv3 write server done A
> (3) ttls : TLS_accept: SSLv3 flush data
> (3) ttls : TLS_accept: Need to read more data: SSLv3 read client
> certificate A
> In SSL Handshake Phase
> In SSL Accept mode
> (3) ttls : eaptls_process returned 13
> (3) [eap] = handled
> Sending Access-Challenge of id 255 to 10.97.0.51 port 49154
> EAP-Message =
> 0x0104040015c00000089b160301002a0200002603014f0756b3dce62ca722a50e1ef6188815
> d5f205a7f1f1550cd636e1ca0e2c358c00002f00160301085e0b00085a0008570003a6308203
> a23082028aa003020102020101300d06092a864886f70d0101050500308193310b3009060355
> 040613024652310f300d060355040813065261646975733112301006035504071309536f6d65
> 776865726531153013060355040a130c4578616d706c6520496e632e3120301e06092a864886
> f70d010901161161646d696e406578616d706c652e636f6d312630240603550403131d457861
> 6d706c6520436572746966696361746520417574686f72697479
> EAP-Message =
> 0x301e170d3132303130353139303230355a170d3133303130343139303230355a307c310b30
> 09060355040613024652310f300d0603550408130652616469757331153013060355040a130c
> 4578616d706c6520496e632e312330210603550403131a4578616d706c652053657276657220
> 43657274696669636174653120301e06092a864886f70d010901161161646d696e406578616d
> 706c652e636f6d30820122300d06092a864886f70d01010105000382010f003082010a028201
> 0100de6164aad9c1017d9e98efb9c6b0c22b8ac67c9da076bab014fcbb499f62f405430309f1
> 09065166a303815b81ec1bb015e964c845f625c8b22fc19d1543
> EAP-Message =
> 0x69b92fae983c34835cf9928df6143e9bf749f2debeb406522c840f4b3c3163099857afed26
> 5426d4208a8e19876c026e2460eaacab04d5e1c2e73b2739ce3fce6db86491016a9b4f4c1b29
> 34f539c3068506092806e0abaae82fa7285df21ca67eafe88ba1d263f7268841e0d360609e89
> 80790063d1197fca1597291bd4433561f36a8e570ea6a530ebf5cc969652d3f09dc1b16bf3b0
> 589f2816056070890f9af6eb9fb1484ba2759bff63410b828f487ecfbccb3f998f93a5b04bcb
> f7619c564b0203010001a317301530130603551d25040c300a06082b06010505070301300d06
> 092a864886f70d010105050003820101003cb3a57f3a4b668e76
> EAP-Message =
> 0x1f26585c44e14542441630ef39baf247bbbc44c9fa9c0e212f0bebe931803bc2ff7e058a58
> a1b9a219f9899b7faaa5edb3bd02ba2f68b10bb50d51f29c9172c0ca063b3a13f99ce28d1ebf
> 2df3f4210152202f8b50b0e94fcbb3b5e740f0b9943cc6d7966e568649d0b616a2d9dbd63563
> 414ec7e9e8b792832b90a8d3f01a2d5afa4ba26e1410935f2fd919bc7ee4ac3406c3c8d21a3e
> caa0bd4e3c3728f086e8aaa420188e48c67a0f4a59f1f6220857af62cd2392092d87f3527ef3
> 7899541dff209215d90cd8f317acfa273945baad0b14e5678ccb9b00c1a599ae17894420d173
> 93cf6d095719d342ba1d941811223e64ab9d0b8d0004ab308204
> EAP-Message = 0xa73082038fa0030201020209
> Message-Authenticator = 0x00000000000000000000000000000000
> State = 0xee37a64fec33b355d3718fb2df57c86c
> (3) Finished request 3.
> Waking up in 0.1 seconds.
> rad_recv: Access-Request packet from host 10.97.0.51 port 49154, id=0,
> length=229
> User-Name = "{am=1}8ea39298d98b6189e0aad92594970151 at WIMAX.COM"
> NAS-IP-Address = 10.97.0.51
> NAS-Port-Type = Wireless-802.16
> NAS-Port = 1
> Calling-Station-Id = "\000\020\347a\r\226"
> NAS-Identifier = "001001003000096000"
> WiMAX-GMT-Timezone-offset = 0
> Framed-MTU = 1490
> Service-Type = Framed-User
> State = 0xee37a64fec33b355d3718fb2df57c86c
> WiMAX-Release = "1.0"
> WiMAX-Accounting-Capabilities = IP-Session-Based
> WiMAX-BS-Id = 0x303031303031303033303030303936303030
> EAP-Message = 0x020400061500
> Message-Authenticator = 0xd9761a90cc87c962fd3b1d9ba3d5c37b
> (4) # Executing section authorize from file
> /usr/local/etc/raddb/sites-enabled/default
> (4) group authorize {
> (4) - entering group authorize {...}
> (4) [preprocess] = ok
> (4) [chap] = noop
> (4) [mschap] = noop
> (4) [digest] = noop
> rlm_wimax: Fixing WiMAX binary Calling-Station-Id to 00-10-e7-61-0d-96
> (4) [wimax] = ok
> (4) suffix : Looking up realm "WIMAX.COM" for User-Name =
> "{am=1}8ea39298d98b6189e0aad92594970151 at WIMAX.COM"
> (4) suffix : No such realm "WIMAX.COM"
> (4) [suffix] = noop
> (4) eap : EAP packet type response id 4 length 6
> (4) eap : Continuing tunnel setup.
> (4) [eap] = ok
> (4) Found Auth-Type = EAP
> (4) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
> (4) group authenticate {
> (4) - entering group authenticate {...}
> (4) eap : Request found, released from the list
> (4) eap : EAP/ttls
> (4) eap : processing type ttls
> (4) ttls : Authenticate
> (4) ttls : processing EAP-TLS
> (4) ttls : Received TLS ACK
> (4) ttls : Received TLS ACK
> (4) ttls : ACK handshake fragment handler
> (4) ttls : eaptls_verify returned 1
> (4) ttls : eaptls_process returned 13
> (4) [eap] = handled
> Sending Access-Challenge of id 0 to 10.97.0.51 port 49154
> EAP-Message =
> 0x0105040015c00000089b00f7aba20691b7a87b300d06092a864886f70d0101050500308193
> 310b3009060355040613024652310f300d060355040813065261646975733112301006035504
> 071309536f6d65776865726531153013060355040a130c4578616d706c6520496e632e312030
> 1e06092a864886f70d010901161161646d696e406578616d706c652e636f6d31263024060355
> 0403131d4578616d706c6520436572746966696361746520417574686f72697479301e170d31
> 32303130353139303230355a170d3133303130343139303230355a308193310b300906035504
> 0613024652310f300d0603550408130652616469757331123010
> EAP-Message =
> 0x06035504071309536f6d65776865726531153013060355040a130c4578616d706c6520496e
> 632e3120301e06092a864886f70d010901161161646d696e406578616d706c652e636f6d3126
> 30240603550403131d4578616d706c6520436572746966696361746520417574686f72697479
> 30820122300d06092a864886f70d01010105000382010f003082010a0282010100bc30533f96
> a0877a3280b984b05dd556c5e33278566f1eaba558868fc2260fd162f73679a4fb97ef499d73
> 434ee850cd698de202197a9417c73e613c7a32e9246d979c7cdba7e1cc8b24eb9760fece85a3
> 1680a58f4626b89e4b11f86c4ccb9e28ff7728a9e230f0a72da7
> EAP-Message =
> 0x7fd3d2beed58c0263c6044fe8459aca3c1e51f9a95ecdf123ed4b783576dfdcd35cc6f14f3
> e70902a05fd0b3e069ffbf26eba77e4b01eb9f0892c8affdf80ec03ba2aa1268edb54f349e95
> 2c03efbf3e44a2d2517e174a5c0db20e703ce797dd98a1e1415b3654e0cc68a6a335f3905bb9
> 3fe92f146f97b6f1cde8dce4f134cf2bf73db5869a9fd31adc0ad68c23eb7a688e20a3d70203
> 010001a381fb3081f8301d0603551d0e04160414c6f2b33fb54c9b615f9cc261e48adbd7c651
> f5253081c80603551d230481c03081bd8014c6f2b33fb54c9b615f9cc261e48adbd7c651f525
> a18199a48196308193310b3009060355040613024652310f300d
> EAP-Message =
> 0x060355040813065261646975733112301006035504071309536f6d65776865726531153013
> 060355040a130c4578616d706c6520496e632e3120301e06092a864886f70d01090116116164
> 6d696e406578616d706c652e636f6d312630240603550403131d4578616d706c652043657274
> 6966696361746520417574686f72697479820900f7aba20691b7a87b300c0603551d13040530
> 030101ff300d06092a864886f70d01010505000382010100b0c9953dd9df2ffa112823d7ceca
> 2bc90bcbe5463161632adfc8d8d86cbc21fa90c3ba769392a4fee11dc2d1f834b44d9fd40f02
> 64f06f657e039352e59e6946c57b0b7723ec446f1ca0f6616cb1
> EAP-Message = 0xf882cb62abfb0d6232ed28a9
> Message-Authenticator = 0x00000000000000000000000000000000
> State = 0xee37a64fed32b355d3718fb2df57c86c
> (4) Finished request 4.
> Waking up in 0.1 seconds.
> Waking up in 0.1 seconds.
> rad_recv: Access-Request packet from host 10.97.0.51 port 49154, id=1,
> length=229
> User-Name = "{am=1}8ea39298d98b6189e0aad92594970151 at WIMAX.COM"
> NAS-IP-Address = 10.97.0.51
> NAS-Port-Type = Wireless-802.16
> NAS-Port = 1
> Calling-Station-Id = "\000\020\347a\r\226"
> NAS-Identifier = "001001003000096000"
> WiMAX-GMT-Timezone-offset = 0
> Framed-MTU = 1490
> Service-Type = Framed-User
> State = 0xee37a64fed32b355d3718fb2df57c86c
> WiMAX-Release = "1.0"
> WiMAX-Accounting-Capabilities = IP-Session-Based
> WiMAX-BS-Id = 0x303031303031303033303030303936303030
> EAP-Message = 0x020500061500
> Message-Authenticator = 0xef737a5a4bd7ccef3fc0193c76fed73d
> (5) # Executing section authorize from file
> /usr/local/etc/raddb/sites-enabled/default
> (5) group authorize {
> (5) - entering group authorize {...}
> (5) [preprocess] = ok
> (5) [chap] = noop
> (5) [mschap] = noop
> (5) [digest] = noop
> rlm_wimax: Fixing WiMAX binary Calling-Station-Id to 00-10-e7-61-0d-96
> (5) [wimax] = ok
> (5) suffix : Looking up realm "WIMAX.COM" for User-Name =
> "{am=1}8ea39298d98b6189e0aad92594970151 at WIMAX.COM"
> (5) suffix : No such realm "WIMAX.COM"
> (5) [suffix] = noop
> (5) eap : EAP packet type response id 5 length 6
> (5) eap : Continuing tunnel setup.
> (5) [eap] = ok
> (5) Found Auth-Type = EAP
> (5) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
> (5) group authenticate {
> (5) - entering group authenticate {...}
> (5) eap : Request found, released from the list
> (5) eap : EAP/ttls
> (5) eap : processing type ttls
> (5) ttls : Authenticate
> (5) ttls : processing EAP-TLS
> (5) ttls : Received TLS ACK
> (5) ttls : Received TLS ACK
> (5) ttls : ACK handshake fragment handler
> (5) ttls : eaptls_verify returned 1
> (5) ttls : eaptls_process returned 13
> (5) [eap] = handled
> Sending Access-Challenge of id 1 to 10.97.0.51 port 49154
> EAP-Message =
> 0x010600b915800000089b3d2597e37be612302c51251c809caf06efe13344d68deb5cfd8abb
> b0ccb8daabe346f1179e51544bb2960cedde88c033d1f68539aaad5f0078a4144e8441407e8f
> 86570400d136f23320d86712d4dbd9887b5d892b7bf71c7fc3862e967c7f8cbfe752971cd38a
> 7a895000823e4166edfe4442df305d728337b4dcd7e4f6d7be981bf5e48730b79fb5500dd8da
> 4ad2db24cda20ad7723b61dd6526cb5d5f724d15c1d73eef0c16030100040e000000
> Message-Authenticator = 0x00000000000000000000000000000000
> State = 0xee37a64fea31b355d3718fb2df57c86c
> (5) Finished request 5.
> Waking up in 0.1 seconds.
> Waking up in 0.1 seconds.
> Waking up in 4.0 seconds.
> rad_recv: Access-Request packet from host 10.97.0.51 port 49154, id=2,
> length=557
> User-Name = "{am=1}8ea39298d98b6189e0aad92594970151 at WIMAX.COM"
> NAS-IP-Address = 10.97.0.51
> NAS-Port-Type = Wireless-802.16
> NAS-Port = 1
> Calling-Station-Id = "\000\020\347a\r\226"
> NAS-Identifier = "001001003000096000"
> WiMAX-GMT-Timezone-offset = 0
> Framed-MTU = 1490
> Service-Type = Framed-User
> State = 0xee37a64fea31b355d3718fb2df57c86c
> WiMAX-Release = "1.0"
> WiMAX-Accounting-Capabilities = IP-Session-Based
> WiMAX-BS-Id = 0x303031303031303033303030303936303030
> EAP-Message =
> 0x0206014c15001603010106100001020100493f1128088cfc52ecfd1411ff5ee55bdf4db01f
> 3fa627cbb785e8bcedff936f3185525d6329b86ba0ef71f41ee7bc889415afa4bc101422f84a
> 68222001fb7cc2f44b26f86ec65a4047ec69a24f1fd60e6fd234d63befb8ae166731c4aec4db
> e4fd1c693136679c6b4094bb218908df95caa0ff8ca6d747bb19ba0d6f5471a7ff30d60ebd89
> 37b3ddc561603cf7ef7a316f04044062efb1eccc1b561f6f1f7ad03e62ac3d439c4de799b4f8
> ba7000f7dcf1c0c6ba15dfdc591d6f82bb112155a8d337f82658c15f9485a363afefb03e0232
> 23bdfce2c84e1deb738d1806b90fea9c69bf5b2173125b529224
> EAP-Message =
> 0x0edc306e48ce048e02c2add34f74027fdcfb6e271403010001011603010030ea083b041af2
> 12a12ae8ffbd04ad129aad64aa9b57e6b0c8a6bcf22be74cababaaa5c3bcd230bab51d055fee
> 3380a470
> Message-Authenticator = 0x5397dd3676e023551a225bcd4c9b4841
> (6) # Executing section authorize from file
> /usr/local/etc/raddb/sites-enabled/default
> (6) group authorize {
> (6) - entering group authorize {...}
> (6) [preprocess] = ok
> (6) [chap] = noop
> (6) [mschap] = noop
> (6) [digest] = noop
> rlm_wimax: Fixing WiMAX binary Calling-Station-Id to 00-10-e7-61-0d-96
> (6) [wimax] = ok
> (6) suffix : Looking up realm "WIMAX.COM" for User-Name =
> "{am=1}8ea39298d98b6189e0aad92594970151 at WIMAX.COM"
> (6) suffix : No such realm "WIMAX.COM"
> (6) [suffix] = noop
> (6) eap : EAP packet type response id 6 length 253
> (6) eap : Continuing tunnel setup.
> (6) [eap] = ok
> (6) Found Auth-Type = EAP
> (6) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
> (6) group authenticate {
> (6) - entering group authenticate {...}
> (6) eap : Request found, released from the list
> (6) eap : EAP/ttls
> (6) eap : processing type ttls
> (6) ttls : Authenticate
> (6) ttls : processing EAP-TLS
> (6) ttls : eaptls_verify returned 7
> (6) ttls : Done initial handshake
> (6) ttls :<<< TLS 1.0 Handshake [length 0106], ClientKeyExchange
> (6) ttls : TLS_accept: SSLv3 read client key exchange A
> (6) ttls :<<< TLS 1.0 ChangeCipherSpec [length 0001]
> (6) ttls :<<< TLS 1.0 Handshake [length 0010], Finished
> (6) ttls : TLS_accept: SSLv3 read finished A
> (6) ttls :>>> TLS 1.0 ChangeCipherSpec [length 0001]
> (6) ttls : TLS_accept: SSLv3 write change cipher spec A
> (6) ttls :>>> TLS 1.0 Handshake [length 0010], Finished
> (6) ttls : TLS_accept: SSLv3 write finished A
> (6) ttls : TLS_accept: SSLv3 flush data
> (6) ttls : (other): SSL negotiation finished successfully
> SSL Connection Established
> (6) ttls : eaptls_process returned 13
> (6) [eap] = handled
> Sending Access-Challenge of id 2 to 10.97.0.51 port 49154
> EAP-Message =
> 0x0107004515800000003b14030100010116030100304d77d31f3558219cd2d5d05b8c42db32
> a2ce0d6bd1da6e97e38197f17d4eac78e578974e0c3354ea36b515b5476332ab
> Message-Authenticator = 0x00000000000000000000000000000000
> State = 0xee37a64feb30b355d3718fb2df57c86c
> (6) Finished request 6.
> Waking up in 0.3 seconds.
> rad_recv: Access-Request packet from host 10.97.0.51 port 49154, id=3,
> length=378
> User-Name = "{am=1}8ea39298d98b6189e0aad92594970151 at WIMAX.COM"
> NAS-IP-Address = 10.97.0.51
> NAS-Port-Type = Wireless-802.16
> NAS-Port = 1
> Calling-Station-Id = "\000\020\347a\r\226"
> NAS-Identifier = "001001003000096000"
> WiMAX-GMT-Timezone-offset = 0
> Framed-MTU = 1490
> Service-Type = Framed-User
> State = 0xee37a64feb30b355d3718fb2df57c86c
> WiMAX-Release = "1.0"
> WiMAX-Accounting-Capabilities = IP-Session-Based
> WiMAX-BS-Id = 0x303031303031303033303030303936303030
> EAP-Message =
> 0x0207009b15001703010090a94a44a2a1a24b0a0392b385be4c524085fc4dfb58cfba7623fc
> 7c790c2d41fc76e98554be526ca2c8006d0a629f426c5d5c33fe724c6ca3081b7c85e42a4d26
> 5a64e46174b8351f823a47031ffb562df9f92c6215742d6a8bde1501cbd573142fc18b05197c
> eb050886a163d0984703554fb9281a249d8037c2e80197f4fc14eca539d1dfa4058805d16490
> ba6e92cd
> Message-Authenticator = 0x0ea984d0f33d209c0596706209586ebe
> (7) # Executing section authorize from file
> /usr/local/etc/raddb/sites-enabled/default
> (7) group authorize {
> (7) - entering group authorize {...}
> (7) [preprocess] = ok
> (7) [chap] = noop
> (7) [mschap] = noop
> (7) [digest] = noop
> rlm_wimax: Fixing WiMAX binary Calling-Station-Id to 00-10-e7-61-0d-96
> (7) [wimax] = ok
> (7) suffix : Looking up realm "WIMAX.COM" for User-Name =
> "{am=1}8ea39298d98b6189e0aad92594970151 at WIMAX.COM"
> (7) suffix : No such realm "WIMAX.COM"
> (7) [suffix] = noop
> (7) eap : EAP packet type response id 7 length 155
> (7) eap : Continuing tunnel setup.
> (7) [eap] = ok
> (7) Found Auth-Type = EAP
> (7) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
> (7) group authenticate {
> (7) - entering group authenticate {...}
> (7) eap : Request found, released from the list
> (7) eap : EAP/ttls
> (7) eap : processing type ttls
> (7) ttls : Authenticate
> (7) ttls : processing EAP-TLS
> (7) ttls : eaptls_verify returned 7
> (7) ttls : Done initial handshake
> (7) ttls : eaptls_process returned 7
> (7) ttls : Session established. Proceeding to decode tunneled attributes.
> (7) ttls : Got tunneled request
> User-Name = "wimax1 at WIMAX.COM"
> MS-CHAP-Challenge = 0x4ff634da70572b920e78e38be8977202
> MS-CHAP2-Response =
> 0x6c00bb3a20c2232fc139ef8b9c65b557b75400000000000000005bc93665692787af9c594f
> c9bc1c22709773fbba940e5ba8
> FreeRADIUS-Proxied-To = 127.0.0.1
> (7) ttls : Sending tunneled request
> User-Name = "wimax1 at WIMAX.COM"
> MS-CHAP-Challenge = 0x4ff634da70572b920e78e38be8977202
> MS-CHAP2-Response =
> 0x6c00bb3a20c2232fc139ef8b9c65b557b75400000000000000005bc93665692787af9c594f
> c9bc1c22709773fbba940e5ba8
> FreeRADIUS-Proxied-To = 127.0.0.1
> server inner-tunnel {
> (7) # Executing section authorize from file
> /usr/local/etc/raddb/sites-enabled/inner-tunnel
> (7) group authorize {
> (7) - entering group authorize {...}
> (7) [chap] = noop
> (7) mschap : Found MS-CHAP attributes. Setting 'Auth-Type = mschap'
> (7) [mschap] = ok
> (7) suffix : Looking up realm "WIMAX.COM" for User-Name = "wimax1 at WIMAX.COM"
> (7) suffix : No such realm "WIMAX.COM"
> (7) [suffix] = noop
> (7) update control {
> (7) } # update control = noop
> (7) eap : No EAP-Message, not doing EAP
> (7) [eap] = noop
> (7) files : users: Matched entry wimax1 at WIMAX.COM at line 4
> (7) [files] = ok
> (7) [expiration] = noop
> (7) [logintime] = noop
> (7) pap : WARNING: Auth-Type already set. Not setting to PAP
> (7) [pap] = noop
> (7) Found Auth-Type = MSCHAP
> (7) # Executing group from file
> /usr/local/etc/raddb/sites-enabled/inner-tunnel
> (7) group MS-CHAP {
> (7) - entering group MS-CHAP {...}
> (7) mschap : Creating challenge hash with username: wimax1 at WIMAX.COM
> (7) mschap : Told to do MS-CHAPv2 for wimax1 at WIMAX.COM with NT-Password
> (7) mschap : adding MS-CHAPv2 MPPE keys
> (7) [mschap] = ok
> (7) WARNING: Empty post-auth section. Using default return values.
> (7) # Executing section post-auth from file
> /usr/local/etc/raddb/sites-enabled/inner-tunnel
> } # server inner-tunnel
> (7) ttls : Got tunneled reply code 2
> Filter-Id = "SP=sp1:MSF=msf1;SP=sp_data_eth:MSF=msf_data_eth;"
> Session-Timeout = 1200
> Termination-Action = RADIUS-Request
> MS-CHAP2-Success =
> 0x6c533d30413343343445383339364636373237324330443444433632433932413444393239
> 444146314633
> MS-MPPE-Recv-Key = 0x9efd76988038d3ccf4f6ab6aa211af6c
> MS-MPPE-Send-Key = 0x2b74cab7d6bdc6e763f480864a5c581b
> MS-MPPE-Encryption-Policy = Encryption-Allowed
> MS-MPPE-Encryption-Types = RC4-40or128-bit-Allowed
> (7) ttls : Got tunneled Access-Accept
> (7) ttls : Got MS-CHAP2-Success, tunneling it to the client in a challenge.
> (7) [eap] = handled
> Sending Access-Challenge of id 3 to 10.97.0.51 port 49154
> EAP-Message =
> 0x0108005f158000000055170301005062cd34a1fec097a2061cc98ee4632f597a42ed4cd80a
> 2d7a7e84c06929acba192114c44395bb6e676d6529843c7618fe2ebe29a179e7ed8f1cfa6692
> e8c775760daca68609f7893158eef62a49fba9eb
> Message-Authenticator = 0x00000000000000000000000000000000
> State = 0xee37a64fe83fb355d3718fb2df57c86c
> (7) Finished request 7.
> Waking up in 0.1 seconds.
> Waking up in 0.1 seconds.
> rad_recv: Access-Request packet from host 10.97.0.51 port 49154, id=4,
> length=229
> User-Name = "{am=1}8ea39298d98b6189e0aad92594970151 at WIMAX.COM"
> NAS-IP-Address = 10.97.0.51
> NAS-Port-Type = Wireless-802.16
> NAS-Port = 1
> Calling-Station-Id = "\000\020\347a\r\226"
> NAS-Identifier = "001001003000096000"
> WiMAX-GMT-Timezone-offset = 0
> Framed-MTU = 1490
> Service-Type = Framed-User
> State = 0xee37a64fe83fb355d3718fb2df57c86c
> WiMAX-Release = "1.0"
> WiMAX-Accounting-Capabilities = IP-Session-Based
> WiMAX-BS-Id = 0x303031303031303033303030303936303030
> EAP-Message = 0x020800061500
> Message-Authenticator = 0xf409f172ed2561c15ab0cbef54e4d1a2
> (8) # Executing section authorize from file
> /usr/local/etc/raddb/sites-enabled/default
> (8) group authorize {
> (8) - entering group authorize {...}
> (8) [preprocess] = ok
> (8) [chap] = noop
> (8) [mschap] = noop
> (8) [digest] = noop
> rlm_wimax: Fixing WiMAX binary Calling-Station-Id to 00-10-e7-61-0d-96
> (8) [wimax] = ok
> (8) suffix : Looking up realm "WIMAX.COM" for User-Name =
> "{am=1}8ea39298d98b6189e0aad92594970151 at WIMAX.COM"
> (8) suffix : No such realm "WIMAX.COM"
> (8) [suffix] = noop
> (8) eap : EAP packet type response id 8 length 6
> (8) eap : Continuing tunnel setup.
> (8) [eap] = ok
> (8) Found Auth-Type = EAP
> (8) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
> (8) group authenticate {
> (8) - entering group authenticate {...}
> (8) eap : Request found, released from the list
> (8) eap : EAP/ttls
> (8) eap : processing type ttls
> (8) ttls : Authenticate
> (8) ttls : processing EAP-TLS
> (8) ttls : Received TLS ACK
> (8) ttls : Received TLS ACK
> (8) ttls : ACK handshake is finished
> (8) ttls : eaptls_verify returned 3
> (8) ttls : eaptls_process returned 3
> (8) ttls : Using saved attributes from the original Access-Accept
> (8) eap : Freeing handler
> (8) [eap] = ok
> (8) # Executing section post-auth from file
> /usr/local/etc/raddb/sites-enabled/default
> (8) group post-auth {
> (8) - entering group post-auth {...}
> (8) [exec] = noop
> (8) update request {
> (8) expand: %{User-Name} ->
> {am=1}8ea39298d98b6189e0aad92594970151 at WIMAX.COM
> (8) } # update request = noop
> (8) update reply {
> (8) expand: %{EAP-MSK} ->
> (8) } # update reply = noop
> (8) wimax : MIP-RK =
> 0xa2cd93eabee4a9a935f0933e2f37c957da9234590d87e33821a353a732f73a28696ae2171e
> 51289b41207e8558e941db6193526d4f6b70ebc740e44c08cae189
> (8) wimax : MIP-SPI = d57e2db6
> (8) wimax : WARNING: WiMAX-IP-Technology not found in reply.
> (8) wimax : WARNING: Not calculating MN-HA keys
> (8) [wimax] = updated
> (8) policy remove_reply_message_if_eap {
> (8) - entering policy remove_reply_message_if_eap {...}
> (8) ? if (reply:EAP-Message&& reply:Reply-Message)
> (8) ? Evaluating (reply:EAP-Message ) -> TRUE
> (8) ? Evaluating (reply:Reply-Message) -> FALSE
> (8) ? if (reply:EAP-Message&& reply:Reply-Message) -> FALSE
> (8) else else {
> (8) - entering else else {...}
> (8) [noop] = noop
> (8) - else else returns noop
> (8) - policy remove_reply_message_if_eap returns noop
> Sending Access-Accept of id 4 to 10.97.0.51 port 49154
> EAP-Message = 0x03080004
> Message-Authenticator = 0x00000000000000000000000000000000
> User-Name = "{am=1}8ea39298d98b6189e0aad92594970151 at WIMAX.COM"
> WiMAX-FA-RK-Key = 0x9081b1490484318c46d65476645a3ea806798046
> WiMAX-MSK = 0x
> WARNING: Skipping zero-length attribute WiMAX-MSK
> WiMAX-MSK =
> 0x0d156b72753d155483788273ff85ed2c67c724fc8e5cbcacee65caeaf5cfff7c62b3f42371
> 331bc2efc2694834c80ad4ba4fe730f9b434c4726a22b5c2c39ecb
> WiMAX-FA-RK-SPI = 3056434901
> (8) Finished request 8.
> Waking up in 0.1 seconds.
> Waking up in 0.1 seconds.
> Waking up in 3.3 seconds.
> (1) Cleaning up request packet ID 253 with timestamp +48 Waking up in 0.1
> seconds.
> (2) Cleaning up request packet ID 254 with timestamp +48 Waking up in 0.1
> seconds.
> (3) Cleaning up request packet ID 255 with timestamp +48 Waking up in 0.1
> seconds.
> (4) Cleaning up request packet ID 0 with timestamp +48 Waking up in 0.1
> seconds.
> (5) Cleaning up request packet ID 1 with timestamp +48 Waking up in 0.3
> seconds.
> (6) Cleaning up request packet ID 2 with timestamp +49 Waking up in 0.1
> seconds.
> (7) Cleaning up request packet ID 3 with timestamp +49 Waking up in 0.1
> seconds.
> (8) Cleaning up request packet ID 4 with timestamp +49 Ready to process
> requests.
>
> -
> List info/subscribe/unsubscribe? See
> http://www.freeradius.org/list/users.html
>
> -
> List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
>
More information about the Freeradius-Users
mailing list