Radius Issue, No response from server

[Russell Mike]

Greetings

FreeRADIUS would only respond if you have NAS entry, else silently ignored.
this is what i can say if you have ping connectivity. XXX should tell the
story as well.
Thanks / RM --


On Wed, Feb 12, 2014 at 8:42 AM, Vijay <amitbutere64 at gmail.com> wrote:

> Hello Michael,
>
> Telnet was just to verify traffic is reaching on radius server or not .
> there's nothing to do with freeradius running on which port.
>
>
>
> Sent from my iPhone
>
> On 12-Feb-2014, at 1:41 PM, Michael Lecuyer <mjl at iterpacis.org> wrote:
>
> >
> >
> > On 2/12/2014 2:41 AM, Vijay wrote:
> >> Hi Rishabh,
> >> I don't think anybody here can help until they see acess-request reaches
> >> radius server.
> >>
> >> Mean while you do the following.
> >> On radius server
> >> Run tcpdump listening for src ip as your nas ip.
> >> From your nas device
> >> Telnet to radius server ip on port 1812
> >
> > You can't telnet to a RADIUS server which uses UDP. You'll get
> 'connection refused' which means nothing in this test since there is no
> RADIUS TCP port.
> >
> > tcpdump will show traffic but you will have to run it BOTH the server
> and the NAS end to demonstrate end to end connectivity.
> >
> >>
> >> This will show if any traffic reaching to radius server.
> >>
> >> Or either your nas sending request on different ports which radius
> >> server expects on.
> >>
> >>
> >> Sent from my iPhone
> >>
> >> On 12-Feb-2014, at 12:28 PM, "Rishabh.Shukla"
> >> <rishabh.shukla at i-link.co.in <mailto:rishabh.shukla at i-link.co.in>>
> wrote:
> >>
> >>> Hi,
> >>>
> >>> Thank you for your reply.  I would like to highlight that I have
> >>> checked that the switch and the radius server can ping each other.
> >>> Moreover, they are on the same network and the routing also works.
> >>> Hence, to me it does not seem like a network issue.
> >>>
> >>> I would greatly appreciate any further help in this regard.
> >>>
> >>> Thanks Again.
> >>>
> >>>
> -------------------------------------------------------------------------------------------
> >>> Best Regards,
> >>> Rishabh
> >>>
> >>> On 2/12/2014 12:06 PM, Rishabh.Shukla wrote:
> >>>
> >>>    ----- Forwarded Message -----
> >>>    From: "HCC Mailing Lists"<hcc.lists at gmail.com>
> >>>    To: "FreeRadius users mailing list"<
> freeradius-users at lists.freeradius.org>
> >>>    Sent: Monday, February 10, 2014 8:25:59 PM
> >>>    Subject: RE: Radius Issue, No response from server
> >>>
> >>>    I may be stating the obvious, but since you have done the
> >>>    configuration perfectly and the packets are not reaching the RADIUS
> >>>    server you might check the configuration of the switch and the
> network
> >>>    to make sure they can reach each other.
> >>>
> >>>        -----Original Message-----
> >>>        From: freeradius-users-
> >>>        bounces+hcc.lists=gmail.com at lists.freeradius.org  [mailto:
> freeradius-
> >>>        users-bounces+hcc.lists=gmail.com at lists.freeradius.org] On
> Behalf Of
> >>>        Rishabh.Shukla
> >>>        Sent: Monday, February 10, 2014 09:11
> >>>        To:freeradius-users at lists.freeradius.org
> >>>        Cc: Hiren Patel; Ronak Shah
> >>>        Subject: Radius Issue, No response from server
> >>>
> >>>        Hello,
> >>>
> >>>        I have deployed radius server + daloradius + MySQL in centos 6
> and
> >>>
> >>>    all
> >>>
> >>>        configuration is done perfectly. I have added HP ProCurve switch
> >>>
> >>>    3400
> >>>
> >>>        CL as my NAS for sending authentication requests.  The
> scenarios is
> >>>        this: the server is responding and accepting the packets
> locally but
> >>>        when I try to authenticate through the HP ProCurve switch the
> server
> >>>        does not respond.
> >>>
> >>>        I have also stopped the iptables services still radius server
> is not
> >>>        listening and during debug we found that the request is not even
> >>>        reaching radius server and moreover I am not getting any error
> >>>        message at all.
> >>>
> >>>        I will be grateful if anybody can help me out to overcome this
> >>>
> >>>    problem.
> >>>
> >>>        Thanks and regards
> >>>        Rishabh.
> >>>        -
> >>>        List info/subscribe/unsubscribe? See
> >>>        http://www.freeradius.org/list/users.html
> >>>
> >>>    -
> >>>    List info/subscribe/unsubscribe? Seehttp://
> www.freeradius.org/list/users.html
> >>>
> >>>
> >>>
> >>> -
> >>> List info/subscribe/unsubscribe? See
> >>> http://www.freeradius.org/list/users.html
> >>
> >>
> >> -
> >> List info/subscribe/unsubscribe? See
> http://www.freeradius.org/list/users.html
> >>
> >
> > -
> > List info/subscribe/unsubscribe? See
> http://www.freeradius.org/list/users.html
> -
> List info/subscribe/unsubscribe? See
> http://www.freeradius.org/list/users.html
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.freeradius.org/pipermail/freeradius-users/attachments/20140212/b31fc42e/attachment-0001.html>