Cross platform secure login on wpa2
Henti Smith
henti at geekware.co.za
Mon Dec 19 16:28:17 CET 2016
On 15 December 2016 at 12:55, Stefan Paetow <Stefan.Paetow at jisc.ac.uk>
wrote:
> > However if I remove the local user and add "DEFAULT Auth-Type = Kerberos"
> > it stops working.
>
> Henti,
>
> If you're using Kerberos as password oracle, you need to set the inner
> tunnel authentication for EAP to PAP. If your systems require that only EAP
> methods are used in the inner tunnel, you're probably best off using 'gtc'
> as the inner (which means EAP-GTC, which is Generic Token Card, which is
> PAP).
>
> Let's assume that PAP is sufficient. In the *inner-tunnel* file you'll
> need some changes in the following sections:
>
> 1. In the authorize section insert the following *after* 'pap':
>
> if (User-Password) {
> update control {
> Auth-Type = Kerberos
> }
> }
>
> 2. In the authenticate section, change the "Auth-Type PAP { ... }" stanza
> to:
>
> Auth-Type PAP {
> # pap
> krb5
> }
>
> Add the following to the authenticate section:
>
> Auth-Type Kerberos {
> krb5
> }
>
> This should call Kerberos with the given password and username depending
> on whether the EAP inner method is set to PAP (via GTC) or Kerberos
> depending on what was fed in.
>
> :-)
>
Good day all.
Thank you for all the advice.
I've upgraded to V3.0.12 and made the config changes as suggested.
Authentication is still not working, but at least I'm now getting krb auth
attempts, which fails due to 'Attribute "User-Password" is required for
authentication'
Please fine log below or at http://hastebin.com/anuxicekut.coffeescript
FreeRADIUS Version 3.0.12
Copyright (C) 1999-2016 The FreeRADIUS server project and contributors
There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A
PARTICULAR PURPOSE
You may redistribute copies of FreeRADIUS under the terms of the
GNU General Public License
For more information about these matters, see the file named COPYRIGHT
Starting - reading configuration files ...
including dictionary file /usr/share/freeradius/dictionary
including dictionary file /usr/share/freeradius/dictionary.dhcp
including dictionary file /usr/share/freeradius/dictionary.vqp
including dictionary file /etc/freeradius/3.0/dictionary
including configuration file /etc/freeradius/3.0/radiusd.conf
including configuration file /etc/freeradius/3.0/proxy.conf
including configuration file /etc/freeradius/3.0/clients.conf
including files in directory /etc/freeradius/3.0/mods-enabled/
including configuration file /etc/freeradius/3.0/mods-enabled/passwd
including configuration file /etc/freeradius/3.0/mods-enabled/realm
including configuration file /etc/freeradius/3.0/mods-enabled/eap
including configuration file /etc/freeradius/3.0/mods-enabled/preprocess
including configuration file /etc/freeradius/3.0/mods-enabled/replicate
including configuration file /etc/freeradius/3.0/mods-enabled/soh
including configuration file /etc/freeradius/3.0/mods-enabled/cache_eap
including configuration file /etc/freeradius/3.0/mods-enabled/digest
including configuration file /etc/freeradius/3.0/mods-enabled/echo
including configuration file /etc/freeradius/3.0/mods-enabled/sradutmp
including configuration file /etc/freeradius/3.0/mods-enabled/utf8
including configuration file /etc/freeradius/3.0/mods-enabled/logintime
including configuration file
/etc/freeradius/3.0/mods-enabled/dynamic_clients
including configuration file /etc/freeradius/3.0/mods-enabled/detail
including configuration file /etc/freeradius/3.0/mods-enabled/expr
including configuration file /etc/freeradius/3.0/mods-enabled/exec
including configuration file /etc/freeradius/3.0/mods-enabled/detail.log
including configuration file /etc/freeradius/3.0/mods-enabled/unpack
including configuration file /etc/freeradius/3.0/mods-enabled/linelog
including configuration file /etc/freeradius/3.0/mods-enabled/pap
including configuration file /etc/freeradius/3.0/mods-enabled/attr_filter
including configuration file /etc/freeradius/3.0/mods-enabled/always
including configuration file /etc/freeradius/3.0/mods-enabled/files
including configuration file /etc/freeradius/3.0/mods-enabled/unix
including configuration file /etc/freeradius/3.0/mods-enabled/mschap
including configuration file /etc/freeradius/3.0/mods-enabled/radutmp
including configuration file /etc/freeradius/3.0/mods-enabled/chap
including configuration file /etc/freeradius/3.0/mods-enabled/ntlm_auth
including configuration file /etc/freeradius/3.0/mods-enabled/krb5
including configuration file /etc/freeradius/3.0/mods-enabled/expiration
including files in directory /etc/freeradius/3.0/policy.d/
including configuration file /etc/freeradius/3.0/policy.d/eap
including configuration file /etc/freeradius/3.0/policy.d/operator-name
including configuration file /etc/freeradius/3.0/policy.d/dhcp
including configuration file
/etc/freeradius/3.0/policy.d/moonshot-targeted-ids
including configuration file /etc/freeradius/3.0/policy.d/abfab-tr
including configuration file /etc/freeradius/3.0/policy.d/control
including configuration file /etc/freeradius/3.0/policy.d/filter
including configuration file /etc/freeradius/3.0/policy.d/cui
including configuration file /etc/freeradius/3.0/policy.d/debug
including configuration file /etc/freeradius/3.0/policy.d/accounting
including configuration file /etc/freeradius/3.0/policy.d/canonicalization
including files in directory /etc/freeradius/3.0/sites-enabled/
including configuration file /etc/freeradius/3.0/sites-enabled/inner-tunnel
including configuration file /etc/freeradius/3.0/sites-enabled/default
main {
security {
user = "freerad"
group = "freerad"
allow_core_dumps = no
}
name = "freeradius"
prefix = "/usr"
localstatedir = "/var"
logdir = "/var/log/freeradius"
run_dir = "/var/run/freeradius"
}
main {
name = "freeradius"
prefix = "/usr"
localstatedir = "/var"
sbindir = "/usr/sbin"
logdir = "/var/log/freeradius"
run_dir = "/var/run/freeradius"
libdir = "/usr/lib/freeradius"
radacctdir = "/var/log/freeradius/radacct"
hostname_lookups = no
max_request_time = 30
cleanup_delay = 5
max_requests = 16384
pidfile = "/var/run/freeradius/freeradius.pid"
checkrad = "/usr/sbin/checkrad"
debug_level = 0
proxy_requests = yes
log {
stripped_names = no
auth = no
auth_badpass = no
auth_goodpass = no
colourise = yes
msg_denied = "You are already logged in - access denied"
}
resources {
}
security {
max_attributes = 200
reject_delay = 1.000000
status_server = yes
}
}
radiusd: #### Loading Realms and Home Servers ####
proxy server {
retry_delay = 5
retry_count = 3
default_fallback = no
dead_time = 120
wake_all_if_all_dead = no
}
home_server localhost {
ipaddr = 127.0.0.1
port = 1812
type = "auth"
secret = <<< secret >>>
response_window = 20.000000
response_timeouts = 1
max_outstanding = 65536
zombie_period = 40
status_check = "status-server"
ping_interval = 30
check_interval = 30
check_timeout = 4
num_answers_to_alive = 3
revive_interval = 120
limit {
max_connections = 16
max_requests = 0
lifetime = 0
idle_timeout = 0
}
coa {
irt = 2
mrt = 16
mrc = 5
mrd = 30
}
}
home_server_pool my_auth_failover {
type = fail-over
home_server = localhost
}
realm example.com {
auth_pool = my_auth_failover
}
realm LOCAL {
}
radiusd: #### Loading Clients ####
client localhost {
ipaddr = 127.0.0.1
require_message_authenticator = no
secret = <<< secret >>>
nas_type = "other"
proto = "*"
limit {
max_connections = 16
lifetime = 0
idle_timeout = 30
}
}
client localhost_ipv6 {
ipv6addr = ::1
require_message_authenticator = no
secret = <<< secret >>>
limit {
max_connections = 16
lifetime = 0
idle_timeout = 30
}
}
Debugger not attached
# Creating Auth-Type = mschap
# Creating Auth-Type = eap
# Creating Auth-Type = PAP
# Creating Auth-Type = kerberos
# Creating Auth-Type = CHAP
# Creating Auth-Type = MS-CHAP
# Creating Auth-Type = digest
radiusd: #### Instantiating modules ####
modules {
# Loaded module rlm_passwd
# Loading module "etc_passwd" from file
/etc/freeradius/3.0/mods-enabled/passwd
passwd etc_passwd {
filename = "/etc/passwd"
format = "*User-Name:Crypt-Password:"
delimiter = ":"
ignore_nislike = no
ignore_empty = yes
allow_multiple_keys = no
hash_size = 100
}
# Loaded module rlm_realm
# Loading module "IPASS" from file /etc/freeradius/3.0/mods-enabled/realm
realm IPASS {
format = "prefix"
delimiter = "/"
ignore_default = no
ignore_null = no
}
# Loading module "suffix" from file /etc/freeradius/3.0/mods-enabled/realm
realm suffix {
format = "suffix"
delimiter = "@"
ignore_default = no
ignore_null = no
}
# Loading module "realmpercent" from file
/etc/freeradius/3.0/mods-enabled/realm
realm realmpercent {
format = "suffix"
delimiter = "%"
ignore_default = no
ignore_null = no
}
# Loading module "ntdomain" from file
/etc/freeradius/3.0/mods-enabled/realm
realm ntdomain {
format = "prefix"
delimiter = "\\"
ignore_default = no
ignore_null = no
}
# Loaded module rlm_eap
# Loading module "eap" from file /etc/freeradius/3.0/mods-enabled/eap
eap {
default_eap_type = "ttls"
timer_expire = 60
ignore_unknown_eap_types = no
cisco_accounting_username_bug = no
max_sessions = 16384
}
# Loaded module rlm_preprocess
# Loading module "preprocess" from file
/etc/freeradius/3.0/mods-enabled/preprocess
preprocess {
huntgroups = "/etc/freeradius/3.0/mods-config/preprocess/huntgroups"
hints = "/etc/freeradius/3.0/mods-config/preprocess/hints"
with_ascend_hack = no
ascend_channels_per_line = 23
with_ntdomain_hack = no
with_specialix_jetstream_hack = no
with_cisco_vsa_hack = no
with_alvarion_vsa_hack = no
}
# Loaded module rlm_replicate
# Loading module "replicate" from file
/etc/freeradius/3.0/mods-enabled/replicate
# Loaded module rlm_soh
# Loading module "soh" from file /etc/freeradius/3.0/mods-enabled/soh
soh {
dhcp = yes
}
# Loaded module rlm_cache
# Loading module "cache_eap" from file
/etc/freeradius/3.0/mods-enabled/cache_eap
cache cache_eap {
driver = "rlm_cache_rbtree"
key = "%{%{control:State}:-%{%{reply:State}:-%{State}}}"
ttl = 15
max_entries = 0
epoch = 0
add_stats = no
}
# Loaded module rlm_digest
# Loading module "digest" from file
/etc/freeradius/3.0/mods-enabled/digest
# Loaded module rlm_exec
# Loading module "echo" from file /etc/freeradius/3.0/mods-enabled/echo
exec echo {
wait = yes
program = "/bin/echo %{User-Name}"
input_pairs = "request"
output_pairs = "reply"
shell_escape = yes
}
# Loaded module rlm_radutmp
# Loading module "sradutmp" from file
/etc/freeradius/3.0/mods-enabled/sradutmp
radutmp sradutmp {
filename = "/var/log/freeradius/sradutmp"
username = "%{User-Name}"
case_sensitive = yes
check_with_nas = yes
permissions = 420
caller_id = no
}
# Loaded module rlm_utf8
# Loading module "utf8" from file /etc/freeradius/3.0/mods-enabled/utf8
# Loaded module rlm_logintime
# Loading module "logintime" from file
/etc/freeradius/3.0/mods-enabled/logintime
logintime {
minimum_timeout = 60
}
# Loaded module rlm_dynamic_clients
# Loading module "dynamic_clients" from file
/etc/freeradius/3.0/mods-enabled/dynamic_clients
# Loaded module rlm_detail
# Loading module "detail" from file
/etc/freeradius/3.0/mods-enabled/detail
detail {
filename =
"/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/detail-%Y%m%d"
header = "%t"
permissions = 384
locking = no
escape_filenames = no
log_packet_header = no
}
# Loaded module rlm_expr
# Loading module "expr" from file /etc/freeradius/3.0/mods-enabled/expr
expr {
safe_characters =
"@abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789.-_:
/äéöüàâæçèéêëîïôœùûüaÿÄÉÖÜßÀÂÆÇÈÉÊËÎÏÔŒÙÛÜŸ"
}
# Loading module "exec" from file /etc/freeradius/3.0/mods-enabled/exec
exec {
wait = no
input_pairs = "request"
shell_escape = yes
timeout = 10
}
# Loading module "auth_log" from file
/etc/freeradius/3.0/mods-enabled/detail.log
detail auth_log {
filename =
"/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d"
header = "%t"
permissions = 384
locking = no
escape_filenames = no
log_packet_header = no
}
# Loading module "reply_log" from file
/etc/freeradius/3.0/mods-enabled/detail.log
detail reply_log {
filename =
"/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/reply-detail-%Y%m%d"
header = "%t"
permissions = 384
locking = no
escape_filenames = no
log_packet_header = no
}
# Loading module "pre_proxy_log" from file
/etc/freeradius/3.0/mods-enabled/detail.log
detail pre_proxy_log {
filename =
"/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/pre-proxy-detail-%Y%m%d"
header = "%t"
permissions = 384
locking = no
escape_filenames = no
log_packet_header = no
}
# Loading module "post_proxy_log" from file
/etc/freeradius/3.0/mods-enabled/detail.log
detail post_proxy_log {
filename =
"/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/post-proxy-detail-%Y%m%d"
header = "%t"
permissions = 384
locking = no
escape_filenames = no
log_packet_header = no
}
# Loaded module rlm_unpack
# Loading module "unpack" from file
/etc/freeradius/3.0/mods-enabled/unpack
# Loaded module rlm_linelog
# Loading module "linelog" from file
/etc/freeradius/3.0/mods-enabled/linelog
linelog {
filename = "/var/log/freeradius/linelog"
escape_filenames = no
syslog_severity = "info"
permissions = 384
format = "This is a log message for %{User-Name}"
reference = "messages.%{%{reply:Packet-Type}:-default}"
}
# Loading module "log_accounting" from file
/etc/freeradius/3.0/mods-enabled/linelog
linelog log_accounting {
filename = "/var/log/freeradius/linelog-accounting"
escape_filenames = no
syslog_severity = "info"
permissions = 384
format = ""
reference = "Accounting-Request.%{%{Acct-Status-Type}:-unknown}"
}
# Loaded module rlm_pap
# Loading module "pap" from file /etc/freeradius/3.0/mods-enabled/pap
pap {
normalise = yes
}
# Loaded module rlm_attr_filter
# Loading module "attr_filter.post-proxy" from file
/etc/freeradius/3.0/mods-enabled/attr_filter
attr_filter attr_filter.post-proxy {
filename = "/etc/freeradius/3.0/mods-config/attr_filter/post-proxy"
key = "%{Realm}"
relaxed = no
}
# Loading module "attr_filter.pre-proxy" from file
/etc/freeradius/3.0/mods-enabled/attr_filter
attr_filter attr_filter.pre-proxy {
filename = "/etc/freeradius/3.0/mods-config/attr_filter/pre-proxy"
key = "%{Realm}"
relaxed = no
}
# Loading module "attr_filter.access_reject" from file
/etc/freeradius/3.0/mods-enabled/attr_filter
attr_filter attr_filter.access_reject {
filename = "/etc/freeradius/3.0/mods-config/attr_filter/access_reject"
key = "%{User-Name}"
relaxed = no
}
# Loading module "attr_filter.access_challenge" from file
/etc/freeradius/3.0/mods-enabled/attr_filter
attr_filter attr_filter.access_challenge {
filename = "/etc/freeradius/3.0/mods-config/attr_filter/access_challenge"
key = "%{User-Name}"
relaxed = no
}
# Loading module "attr_filter.accounting_response" from file
/etc/freeradius/3.0/mods-enabled/attr_filter
attr_filter attr_filter.accounting_response {
filename =
"/etc/freeradius/3.0/mods-config/attr_filter/accounting_response"
key = "%{User-Name}"
relaxed = no
}
# Loaded module rlm_always
# Loading module "reject" from file
/etc/freeradius/3.0/mods-enabled/always
always reject {
rcode = "reject"
simulcount = 0
mpp = no
}
# Loading module "fail" from file /etc/freeradius/3.0/mods-enabled/always
always fail {
rcode = "fail"
simulcount = 0
mpp = no
}
# Loading module "ok" from file /etc/freeradius/3.0/mods-enabled/always
always ok {
rcode = "ok"
simulcount = 0
mpp = no
}
# Loading module "handled" from file
/etc/freeradius/3.0/mods-enabled/always
always handled {
rcode = "handled"
simulcount = 0
mpp = no
}
# Loading module "invalid" from file
/etc/freeradius/3.0/mods-enabled/always
always invalid {
rcode = "invalid"
simulcount = 0
mpp = no
}
# Loading module "userlock" from file
/etc/freeradius/3.0/mods-enabled/always
always userlock {
rcode = "userlock"
simulcount = 0
mpp = no
}
# Loading module "notfound" from file
/etc/freeradius/3.0/mods-enabled/always
always notfound {
rcode = "notfound"
simulcount = 0
mpp = no
}
# Loading module "noop" from file /etc/freeradius/3.0/mods-enabled/always
always noop {
rcode = "noop"
simulcount = 0
mpp = no
}
# Loading module "updated" from file
/etc/freeradius/3.0/mods-enabled/always
always updated {
rcode = "updated"
simulcount = 0
mpp = no
}
# Loaded module rlm_files
# Loading module "files" from file /etc/freeradius/3.0/mods-enabled/files
files {
filename = "/etc/freeradius/3.0/mods-config/files/authorize"
acctusersfile = "/etc/freeradius/3.0/mods-config/files/accounting"
preproxy_usersfile = "/etc/freeradius/3.0/mods-config/files/pre-proxy"
}
# Loaded module rlm_unix
# Loading module "unix" from file /etc/freeradius/3.0/mods-enabled/unix
unix {
radwtmp = "/var/log/freeradius/radwtmp"
}
Creating attribute Unix-Group
# Loaded module rlm_mschap
# Loading module "mschap" from file
/etc/freeradius/3.0/mods-enabled/mschap
mschap {
use_mppe = yes
require_encryption = no
require_strong = no
with_ntdomain_hack = yes
passchange {
}
allow_retry = yes
}
# Loading module "radutmp" from file
/etc/freeradius/3.0/mods-enabled/radutmp
radutmp {
filename = "/var/log/freeradius/radutmp"
username = "%{User-Name}"
case_sensitive = yes
check_with_nas = yes
permissions = 384
caller_id = yes
}
# Loaded module rlm_chap
# Loading module "chap" from file /etc/freeradius/3.0/mods-enabled/chap
# Loading module "ntlm_auth" from file
/etc/freeradius/3.0/mods-enabled/ntlm_auth
exec ntlm_auth {
wait = yes
program = "/path/to/ntlm_auth --request-nt-key --domain=MYDOMAIN
--username=%{mschap:User-Name} --password=%{User-Password}"
shell_escape = yes
}
# Loaded module rlm_krb5
# Loading module "krb5" from file /etc/freeradius/3.0/mods-enabled/krb5
krb5 {
keytab = "/etc/radius-01.internal.somecompany.com.keytab"
service_principal = "radius/radius-01.internal.somecompany.com"
}
# Loaded module rlm_expiration
# Loading module "expiration" from file
/etc/freeradius/3.0/mods-enabled/expiration
instantiate {
}
# Instantiating module "etc_passwd" from file
/etc/freeradius/3.0/mods-enabled/passwd
rlm_passwd: nfields: 3 keyfield 0(User-Name) listable: no
# Instantiating module "IPASS" from file
/etc/freeradius/3.0/mods-enabled/realm
# Instantiating module "suffix" from file
/etc/freeradius/3.0/mods-enabled/realm
# Instantiating module "realmpercent" from file
/etc/freeradius/3.0/mods-enabled/realm
# Instantiating module "ntdomain" from file
/etc/freeradius/3.0/mods-enabled/realm
# Instantiating module "eap" from file
/etc/freeradius/3.0/mods-enabled/eap
# Linked to sub-module rlm_eap_md5
# Linked to sub-module rlm_eap_leap
# Linked to sub-module rlm_eap_gtc
gtc {
challenge = "Password: "
auth_type = "PAP"
}
# Linked to sub-module rlm_eap_tls
tls {
tls = "tls-common"
}
tls-config tls-common {
verify_depth = 0
ca_path = "/etc/freeradius/3.0/certs"
pem_file_type = yes
private_key_file =
"/etc/ssl/private/STAR.internal.somecompany.com.key.pem"
certificate_file =
"/etc/ssl/certs/STAR.internal.somecompany.com.crt.pem"
ca_file = "/etc/ssl/certs/Comodo_chain.crt.pem"
dh_file = "/etc/freeradius/3.0/certs/dh"
fragment_size = 1024
include_length = yes
auto_chain = yes
check_crl = no
check_all_crl = no
cipher_list = "DEFAULT"
ecdh_curve = "prime256v1"
cache {
enable = yes
lifetime = 24
max_entries = 255
}
verify {
skip_if_ocsp_ok = no
}
ocsp {
enable = no
override_cert_url = yes
url = "http://127.0.0.1/ocsp/"
use_nonce = yes
timeout = 0
softfail = no
}
}
# Linked to sub-module rlm_eap_ttls
ttls {
tls = "tls-common"
default_eap_type = "md5"
copy_request_to_tunnel = yes
use_tunneled_reply = yes
virtual_server = "inner-tunnel"
include_length = yes
require_client_cert = no
}
tls: Using cached TLS configuration from previous invocation
# Linked to sub-module rlm_eap_peap
peap {
tls = "tls-common"
default_eap_type = "mschapv2"
copy_request_to_tunnel = no
use_tunneled_reply = no
proxy_tunneled_request_as_eap = yes
virtual_server = "inner-tunnel"
soh = no
require_client_cert = no
}
tls: Using cached TLS configuration from previous invocation
# Linked to sub-module rlm_eap_mschapv2
mschapv2 {
with_ntdomain_hack = no
send_error = no
}
# Instantiating module "preprocess" from file
/etc/freeradius/3.0/mods-enabled/preprocess
reading pairlist file /etc/freeradius/3.0/mods-config/preprocess/huntgroups
reading pairlist file /etc/freeradius/3.0/mods-config/preprocess/hints
# Instantiating module "cache_eap" from file
/etc/freeradius/3.0/mods-enabled/cache_eap
rlm_cache (cache_eap): Driver rlm_cache_rbtree (module rlm_cache_rbtree)
loaded and linked
# Instantiating module "logintime" from file
/etc/freeradius/3.0/mods-enabled/logintime
# Instantiating module "detail" from file
/etc/freeradius/3.0/mods-enabled/detail
# Instantiating module "auth_log" from file
/etc/freeradius/3.0/mods-enabled/detail.log
rlm_detail (auth_log): 'User-Password' suppressed, will not appear in
detail output
# Instantiating module "reply_log" from file
/etc/freeradius/3.0/mods-enabled/detail.log
# Instantiating module "pre_proxy_log" from file
/etc/freeradius/3.0/mods-enabled/detail.log
# Instantiating module "post_proxy_log" from file
/etc/freeradius/3.0/mods-enabled/detail.log
# Instantiating module "linelog" from file
/etc/freeradius/3.0/mods-enabled/linelog
# Instantiating module "log_accounting" from file
/etc/freeradius/3.0/mods-enabled/linelog
# Instantiating module "pap" from file
/etc/freeradius/3.0/mods-enabled/pap
# Instantiating module "attr_filter.post-proxy" from file
/etc/freeradius/3.0/mods-enabled/attr_filter
reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/post-proxy
# Instantiating module "attr_filter.pre-proxy" from file
/etc/freeradius/3.0/mods-enabled/attr_filter
reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/pre-proxy
# Instantiating module "attr_filter.access_reject" from file
/etc/freeradius/3.0/mods-enabled/attr_filter
reading pairlist file
/etc/freeradius/3.0/mods-config/attr_filter/access_reject
[/etc/freeradius/3.0/mods-config/attr_filter/access_reject]:11 Check item
"FreeRADIUS-Response-Delay" found in filter list for realm "DEFAULT".
[/etc/freeradius/3.0/mods-config/attr_filter/access_reject]:11 Check item
"FreeRADIUS-Response-Delay-USec" found in filter list for realm "DEFAULT".
# Instantiating module "attr_filter.access_challenge" from file
/etc/freeradius/3.0/mods-enabled/attr_filter
reading pairlist file
/etc/freeradius/3.0/mods-config/attr_filter/access_challenge
# Instantiating module "attr_filter.accounting_response" from file
/etc/freeradius/3.0/mods-enabled/attr_filter
reading pairlist file
/etc/freeradius/3.0/mods-config/attr_filter/accounting_response
# Instantiating module "reject" from file
/etc/freeradius/3.0/mods-enabled/always
# Instantiating module "fail" from file
/etc/freeradius/3.0/mods-enabled/always
# Instantiating module "ok" from file
/etc/freeradius/3.0/mods-enabled/always
# Instantiating module "handled" from file
/etc/freeradius/3.0/mods-enabled/always
# Instantiating module "invalid" from file
/etc/freeradius/3.0/mods-enabled/always
# Instantiating module "userlock" from file
/etc/freeradius/3.0/mods-enabled/always
# Instantiating module "notfound" from file
/etc/freeradius/3.0/mods-enabled/always
# Instantiating module "noop" from file
/etc/freeradius/3.0/mods-enabled/always
# Instantiating module "updated" from file
/etc/freeradius/3.0/mods-enabled/always
# Instantiating module "files" from file
/etc/freeradius/3.0/mods-enabled/files
reading pairlist file /etc/freeradius/3.0/mods-config/files/authorize
reading pairlist file /etc/freeradius/3.0/mods-config/files/accounting
reading pairlist file /etc/freeradius/3.0/mods-config/files/pre-proxy
# Instantiating module "mschap" from file
/etc/freeradius/3.0/mods-enabled/mschap
rlm_mschap (mschap): using internal authentication
# Instantiating module "krb5" from file
/etc/freeradius/3.0/mods-enabled/krb5
Using MIT Kerberos library
rlm_krb5 (krb5): Using service principal
"radius/radius-01.internal.somecompany.com@"
rlm_krb5 (krb5): Using keytab
"FILE:/etc/radius-01.internal.somecompany.com.keytab"
rlm_krb5 (krb5): Initialising connection pool
pool {
start = 5
min = 3
max = 32
spare = 10
uses = 0
lifetime = 0
cleanup_interval = 30
idle_timeout = 0
retry_delay = 1
spread = no
}
rlm_krb5 (krb5): Opening additional connection (0), 1 of 32 pending slots
used
rlm_krb5 (krb5): Opening additional connection (1), 1 of 31 pending slots
used
rlm_krb5 (krb5): Opening additional connection (2), 1 of 30 pending slots
used
rlm_krb5 (krb5): Opening additional connection (3), 1 of 29 pending slots
used
rlm_krb5 (krb5): Opening additional connection (4), 1 of 28 pending slots
used
# Instantiating module "expiration" from file
/etc/freeradius/3.0/mods-enabled/expiration
} # modules
radiusd: #### Loading Virtual Servers ####
server { # from file /etc/freeradius/3.0/radiusd.conf
} # server
server inner-tunnel { # from file
/etc/freeradius/3.0/sites-enabled/inner-tunnel
# Loading authenticate {...}
# Loading authorize {...}
Ignoring "sql" (see raddb/mods-available/README.rst)
Ignoring "ldap" (see raddb/mods-available/README.rst)
# Loading session {...}
# Loading post-proxy {...}
# Loading post-auth {...}
} # server inner-tunnel
server default { # from file /etc/freeradius/3.0/sites-enabled/default
# Loading authenticate {...}
# Loading authorize {...}
# Loading preacct {...}
# Loading accounting {...}
# Loading post-proxy {...}
# Loading post-auth {...}
} # server default
radiusd: #### Opening IP addresses and Ports ####
listen {
type = "auth"
ipaddr = 127.0.0.1
port = 18120
}
listen {
type = "auth"
ipaddr = *
port = 0
limit {
max_connections = 16
lifetime = 0
idle_timeout = 30
}
}
listen {
type = "acct"
ipaddr = *
port = 0
limit {
max_connections = 16
lifetime = 0
idle_timeout = 30
}
}
listen {
type = "auth"
ipv6addr = ::
port = 0
limit {
max_connections = 16
lifetime = 0
idle_timeout = 30
}
}
listen {
type = "acct"
ipv6addr = ::
port = 0
limit {
max_connections = 16
lifetime = 0
idle_timeout = 30
}
}
Listening on auth address 127.0.0.1 port 18120 bound to server inner-tunnel
Listening on auth address * port 1812 bound to server default
Listening on acct address * port 1813 bound to server default
Listening on auth address :: port 1812 bound to server default
Listening on acct address :: port 1813 bound to server default
Listening on proxy address * port 59959
Listening on proxy address :: port 34159
Ready to process requests
(0) Received Access-Request Id 0 from 127.0.0.1:45118 to 127.0.0.1:1812
length 143
(0) User-Name = "kerberos-test"
(0) NAS-IP-Address = 127.0.0.1
(0) Calling-Station-Id = "70-6F-6C-69-73-68"
(0) Framed-MTU = 1400
(0) NAS-Port-Type = Wireless-802.11
(0) Service-Type = Framed-User
(0) Connect-Info = "rad_eap_test + eapol_test"
(0) EAP-Message = 0x02000012016b65726265726f732d74657374
(0) Message-Authenticator = 0x4a27f1fa7a83ded3e7ca38e92cdbdd89
(0) # Executing section authorize from file
/etc/freeradius/3.0/sites-enabled/default
(0) authorize {
(0) policy filter_username {
(0) if (&User-Name) {
(0) if (&User-Name) -> TRUE
(0) if (&User-Name) {
(0) if (&User-Name =~ / /) {
(0) if (&User-Name =~ / /) -> FALSE
(0) if (&User-Name =~ /@[^@]*@/ ) {
(0) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(0) if (&User-Name =~ /\.\./ ) {
(0) if (&User-Name =~ /\.\./ ) -> FALSE
(0) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(0) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) ->
FALSE
(0) if (&User-Name =~ /\.$/) {
(0) if (&User-Name =~ /\.$/) -> FALSE
(0) if (&User-Name =~ /@\./) {
(0) if (&User-Name =~ /@\./) -> FALSE
(0) } # if (&User-Name) = notfound
(0) } # policy filter_username = notfound
(0) [preprocess] = ok
(0) [chap] = noop
(0) [mschap] = noop
(0) [digest] = noop
(0) suffix: Checking for suffix after "@"
(0) suffix: No '@' in User-Name = "kerberos-test", looking up realm NULL
(0) suffix: No such realm "NULL"
(0) [suffix] = noop
(0) eap: Peer sent EAP Response (code 2) ID 0 length 18
(0) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the
rest of authorize
(0) [eap] = ok
(0) } # authorize = ok
(0) Found Auth-Type = eap
(0) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(0) authenticate {
(0) eap: Peer sent packet with method EAP Identity (1)
(0) eap: Calling submodule eap_ttls to process data
(0) eap_ttls: Initiating new EAP-TLS session
(0) eap_ttls: Flushing SSL sessions (of #0)
(0) eap_ttls: [eaptls start] = request
(0) eap: Sending EAP Request (code 1) ID 1 length 6
(0) eap: EAP session adding &reply:State = 0xf2dc3f6df2dd2a6f
(0) [eap] = handled
(0) } # authenticate = handled
(0) Using Post-Auth-Type Challenge
(0) Post-Auth-Type sub-section not found. Ignoring.
(0) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(0) Sent Access-Challenge Id 0 from 127.0.0.1:1812 to 127.0.0.1:45118
length 0
(0) EAP-Message = 0x010100061520
(0) Message-Authenticator = 0x00000000000000000000000000000000
(0) State = 0xf2dc3f6df2dd2a6f134bb1f97963cb4c
(0) Finished request
Waking up in 4.9 seconds.
(1) Received Access-Request Id 1 from 127.0.0.1:45118 to 127.0.0.1:1812
length 436
(1) User-Name = "kerberos-test"
(1) NAS-IP-Address = 127.0.0.1
(1) Calling-Station-Id = "70-6F-6C-69-73-68"
(1) Framed-MTU = 1400
(1) NAS-Port-Type = Wireless-802.11
(1) Service-Type = Framed-User
(1) Connect-Info = "rad_eap_test + eapol_test"
(1) EAP-Message =
0x020101231500160301011801000114030322b55cd7fde77a7340d5401bd560d8f658ee0c33609e947271663dbd474b5cb1000082c030c02cc028c024c014c00a00a3009f006b006a0039003800880087c032c02ec02ac026c00fc005009d003d00350084c02fc02bc027c023c013c00900a2009e006700
(1) State = 0xf2dc3f6df2dd2a6f134bb1f97963cb4c
(1) Message-Authenticator = 0x4aeed1e589f44dea2df6455fb104caf3
(1) session-state: No cached attributes
(1) # Executing section authorize from file
/etc/freeradius/3.0/sites-enabled/default
(1) authorize {
(1) policy filter_username {
(1) if (&User-Name) {
(1) if (&User-Name) -> TRUE
(1) if (&User-Name) {
(1) if (&User-Name =~ / /) {
(1) if (&User-Name =~ / /) -> FALSE
(1) if (&User-Name =~ /@[^@]*@/ ) {
(1) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(1) if (&User-Name =~ /\.\./ ) {
(1) if (&User-Name =~ /\.\./ ) -> FALSE
(1) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(1) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) ->
FALSE
(1) if (&User-Name =~ /\.$/) {
(1) if (&User-Name =~ /\.$/) -> FALSE
(1) if (&User-Name =~ /@\./) {
(1) if (&User-Name =~ /@\./) -> FALSE
(1) } # if (&User-Name) = notfound
(1) } # policy filter_username = notfound
(1) [preprocess] = ok
(1) [chap] = noop
(1) [mschap] = noop
(1) [digest] = noop
(1) suffix: Checking for suffix after "@"
(1) suffix: No '@' in User-Name = "kerberos-test", looking up realm NULL
(1) suffix: No such realm "NULL"
(1) [suffix] = noop
(1) eap: Peer sent EAP Response (code 2) ID 1 length 291
(1) eap: Continuing tunnel setup
(1) [eap] = ok
(1) } # authorize = ok
(1) Found Auth-Type = eap
(1) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(1) authenticate {
(1) eap: Expiring EAP session with state 0xf2dc3f6df2dd2a6f
(1) eap: Finished EAP session with state 0xf2dc3f6df2dd2a6f
(1) eap: Previous EAP request found for state 0xf2dc3f6df2dd2a6f, released
from the list
(1) eap: Peer sent packet with method EAP TTLS (21)
(1) eap: Calling submodule eap_ttls to process data
(1) eap_ttls: Authenticate
(1) eap_ttls: Continuing EAP-TLS
(1) eap_ttls: Got final TLS record fragment (285 bytes)
(1) eap_ttls: WARNING: Total received TLS record fragments (285 bytes),
does not equal indicated TLS record length (0 bytes)
(1) eap_ttls: [eaptls verify] = ok
(1) eap_ttls: Done initial handshake
(1) eap_ttls: (other): before/accept initialization
(1) eap_ttls: TLS_accept: before/accept initialization
(1) eap_ttls: <<< recv TLS 1.2 [length 0118]
(1) eap_ttls: TLS_accept: unknown state
(1) eap_ttls: >>> send TLS 1.2 [length 005e]
(1) eap_ttls: TLS_accept: unknown state
(1) eap_ttls: >>> send TLS 1.2 [length 1100]
(1) eap_ttls: TLS_accept: unknown state
(1) eap_ttls: >>> send TLS 1.2 [length 014d]
(1) eap_ttls: TLS_accept: unknown state
(1) eap_ttls: >>> send TLS 1.2 [length 0004]
(1) eap_ttls: TLS_accept: unknown state
(1) eap_ttls: TLS_accept: unknown state
(1) eap_ttls: TLS_accept: Need to read more data: unknown state
(1) eap_ttls: TLS_accept: Need to read more data: unknown state
(1) eap_ttls: In SSL Handshake Phase
(1) eap_ttls: In SSL Accept mode
(1) eap_ttls: [eaptls process] = handled
(1) eap: Sending EAP Request (code 1) ID 2 length 1004
(1) eap: EAP session adding &reply:State = 0xf2dc3f6df3de2a6f
(1) [eap] = handled
(1) } # authenticate = handled
(1) Using Post-Auth-Type Challenge
(1) Post-Auth-Type sub-section not found. Ignoring.
(1) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(1) Sent Access-Challenge Id 1 from 127.0.0.1:1812 to 127.0.0.1:45118
length 0
(1) EAP-Message =
0x010203ec15c0000012c3160303005e0200005a0303b2fd4a21010f81be5c6616795d541c1be8624ead488fd44fedd42a1cee9c93a22027845a3d43459a266666dd69d39152b816629599644b72e57ca8151f78353614c030000012ff01000100000b000403000102000f00010116030311000b0010fc00
(1) Message-Authenticator = 0x00000000000000000000000000000000
(1) State = 0xf2dc3f6df3de2a6f134bb1f97963cb4c
(1) Finished request
Waking up in 4.9 seconds.
(2) Received Access-Request Id 2 from 127.0.0.1:45118 to 127.0.0.1:1812
length 149
(2) User-Name = "kerberos-test"
(2) NAS-IP-Address = 127.0.0.1
(2) Calling-Station-Id = "70-6F-6C-69-73-68"
(2) Framed-MTU = 1400
(2) NAS-Port-Type = Wireless-802.11
(2) Service-Type = Framed-User
(2) Connect-Info = "rad_eap_test + eapol_test"
(2) EAP-Message = 0x020200061500
(2) State = 0xf2dc3f6df3de2a6f134bb1f97963cb4c
(2) Message-Authenticator = 0xae0d22b8d0c5d2712a952c12d8dedb3e
(2) session-state: No cached attributes
(2) # Executing section authorize from file
/etc/freeradius/3.0/sites-enabled/default
(2) authorize {
(2) policy filter_username {
(2) if (&User-Name) {
(2) if (&User-Name) -> TRUE
(2) if (&User-Name) {
(2) if (&User-Name =~ / /) {
(2) if (&User-Name =~ / /) -> FALSE
(2) if (&User-Name =~ /@[^@]*@/ ) {
(2) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(2) if (&User-Name =~ /\.\./ ) {
(2) if (&User-Name =~ /\.\./ ) -> FALSE
(2) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(2) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) ->
FALSE
(2) if (&User-Name =~ /\.$/) {
(2) if (&User-Name =~ /\.$/) -> FALSE
(2) if (&User-Name =~ /@\./) {
(2) if (&User-Name =~ /@\./) -> FALSE
(2) } # if (&User-Name) = notfound
(2) } # policy filter_username = notfound
(2) [preprocess] = ok
(2) [chap] = noop
(2) [mschap] = noop
(2) [digest] = noop
(2) suffix: Checking for suffix after "@"
(2) suffix: No '@' in User-Name = "kerberos-test", looking up realm NULL
(2) suffix: No such realm "NULL"
(2) [suffix] = noop
(2) eap: Peer sent EAP Response (code 2) ID 2 length 6
(2) eap: Continuing tunnel setup
(2) [eap] = ok
(2) } # authorize = ok
(2) Found Auth-Type = eap
(2) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(2) authenticate {
(2) eap: Expiring EAP session with state 0xf2dc3f6df3de2a6f
(2) eap: Finished EAP session with state 0xf2dc3f6df3de2a6f
(2) eap: Previous EAP request found for state 0xf2dc3f6df3de2a6f, released
from the list
(2) eap: Peer sent packet with method EAP TTLS (21)
(2) eap: Calling submodule eap_ttls to process data
(2) eap_ttls: Authenticate
(2) eap_ttls: Continuing EAP-TLS
(2) eap_ttls: Peer ACKed our handshake fragment
(2) eap_ttls: [eaptls verify] = request
(2) eap_ttls: [eaptls process] = handled
(2) eap: Sending EAP Request (code 1) ID 3 length 1004
(2) eap: EAP session adding &reply:State = 0xf2dc3f6df0df2a6f
(2) [eap] = handled
(2) } # authenticate = handled
(2) Using Post-Auth-Type Challenge
(2) Post-Auth-Type sub-section not found. Ignoring.
(2) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(2) Sent Access-Challenge Id 2 from 127.0.0.1:1812 to 127.0.0.1:45118
length 0
(2) EAP-Message =
0x010303ec15c0000012c34d4f444f525341446f6d61696e56616c69646174696f6e53656375726553657276657243412e63726c30818506082b0601050507010104793077304f06082b060105050730028643687474703a2f2f6372742e636f6d6f646f63612e636f6d2f434f4d4f444f525341446f6d61
(2) Message-Authenticator = 0x00000000000000000000000000000000
(2) State = 0xf2dc3f6df0df2a6f134bb1f97963cb4c
(2) Finished request
Waking up in 4.9 seconds.
(3) Received Access-Request Id 3 from 127.0.0.1:45118 to 127.0.0.1:1812
length 149
(3) User-Name = "kerberos-test"
(3) NAS-IP-Address = 127.0.0.1
(3) Calling-Station-Id = "70-6F-6C-69-73-68"
(3) Framed-MTU = 1400
(3) NAS-Port-Type = Wireless-802.11
(3) Service-Type = Framed-User
(3) Connect-Info = "rad_eap_test + eapol_test"
(3) EAP-Message = 0x020300061500
(3) State = 0xf2dc3f6df0df2a6f134bb1f97963cb4c
(3) Message-Authenticator = 0xb4d761cdba8fa2e9358e1d7a51c11d27
(3) session-state: No cached attributes
(3) # Executing section authorize from file
/etc/freeradius/3.0/sites-enabled/default
(3) authorize {
(3) policy filter_username {
(3) if (&User-Name) {
(3) if (&User-Name) -> TRUE
(3) if (&User-Name) {
(3) if (&User-Name =~ / /) {
(3) if (&User-Name =~ / /) -> FALSE
(3) if (&User-Name =~ /@[^@]*@/ ) {
(3) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(3) if (&User-Name =~ /\.\./ ) {
(3) if (&User-Name =~ /\.\./ ) -> FALSE
(3) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(3) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) ->
FALSE
(3) if (&User-Name =~ /\.$/) {
(3) if (&User-Name =~ /\.$/) -> FALSE
(3) if (&User-Name =~ /@\./) {
(3) if (&User-Name =~ /@\./) -> FALSE
(3) } # if (&User-Name) = notfound
(3) } # policy filter_username = notfound
(3) [preprocess] = ok
(3) [chap] = noop
(3) [mschap] = noop
(3) [digest] = noop
(3) suffix: Checking for suffix after "@"
(3) suffix: No '@' in User-Name = "kerberos-test", looking up realm NULL
(3) suffix: No such realm "NULL"
(3) [suffix] = noop
(3) eap: Peer sent EAP Response (code 2) ID 3 length 6
(3) eap: Continuing tunnel setup
(3) [eap] = ok
(3) } # authorize = ok
(3) Found Auth-Type = eap
(3) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(3) authenticate {
(3) eap: Expiring EAP session with state 0xf2dc3f6df0df2a6f
(3) eap: Finished EAP session with state 0xf2dc3f6df0df2a6f
(3) eap: Previous EAP request found for state 0xf2dc3f6df0df2a6f, released
from the list
(3) eap: Peer sent packet with method EAP TTLS (21)
(3) eap: Calling submodule eap_ttls to process data
(3) eap_ttls: Authenticate
(3) eap_ttls: Continuing EAP-TLS
(3) eap_ttls: Peer ACKed our handshake fragment
(3) eap_ttls: [eaptls verify] = request
(3) eap_ttls: [eaptls process] = handled
(3) eap: Sending EAP Request (code 1) ID 4 length 1004
(3) eap: EAP session adding &reply:State = 0xf2dc3f6df1d82a6f
(3) [eap] = handled
(3) } # authenticate = handled
(3) Using Post-Auth-Type Challenge
(3) Post-Auth-Type sub-section not found. Ignoring.
(3) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(3) Sent Access-Challenge Id 3 from 127.0.0.1:1812 to 127.0.0.1:45118
length 0
(3) EAP-Message =
0x010403ec15c0000012c397f7be67de9ed07aa753803b7cadf596556f97470a7c858b22978db384e09657d0701860968fee2d07939da1bacad1cd7be9c42a9a2821914d6f924f25a5f27a35dd26dc46a5d0ac59358cff4e9143503f59931e6c5121ee5814abfe7550783e4cb01c8613fa6b98bce03b941e
(3) Message-Authenticator = 0x00000000000000000000000000000000
(3) State = 0xf2dc3f6df1d82a6f134bb1f97963cb4c
(3) Finished request
Waking up in 4.9 seconds.
(4) Received Access-Request Id 4 from 127.0.0.1:45118 to 127.0.0.1:1812
length 149
(4) User-Name = "kerberos-test"
(4) NAS-IP-Address = 127.0.0.1
(4) Calling-Station-Id = "70-6F-6C-69-73-68"
(4) Framed-MTU = 1400
(4) NAS-Port-Type = Wireless-802.11
(4) Service-Type = Framed-User
(4) Connect-Info = "rad_eap_test + eapol_test"
(4) EAP-Message = 0x020400061500
(4) State = 0xf2dc3f6df1d82a6f134bb1f97963cb4c
(4) Message-Authenticator = 0x97294509190a66e772cd28cd5fc7c042
(4) session-state: No cached attributes
(4) # Executing section authorize from file
/etc/freeradius/3.0/sites-enabled/default
(4) authorize {
(4) policy filter_username {
(4) if (&User-Name) {
(4) if (&User-Name) -> TRUE
(4) if (&User-Name) {
(4) if (&User-Name =~ / /) {
(4) if (&User-Name =~ / /) -> FALSE
(4) if (&User-Name =~ /@[^@]*@/ ) {
(4) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(4) if (&User-Name =~ /\.\./ ) {
(4) if (&User-Name =~ /\.\./ ) -> FALSE
(4) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(4) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) ->
FALSE
(4) if (&User-Name =~ /\.$/) {
(4) if (&User-Name =~ /\.$/) -> FALSE
(4) if (&User-Name =~ /@\./) {
(4) if (&User-Name =~ /@\./) -> FALSE
(4) } # if (&User-Name) = notfound
(4) } # policy filter_username = notfound
(4) [preprocess] = ok
(4) [chap] = noop
(4) [mschap] = noop
(4) [digest] = noop
(4) suffix: Checking for suffix after "@"
(4) suffix: No '@' in User-Name = "kerberos-test", looking up realm NULL
(4) suffix: No such realm "NULL"
(4) [suffix] = noop
(4) eap: Peer sent EAP Response (code 2) ID 4 length 6
(4) eap: Continuing tunnel setup
(4) [eap] = ok
(4) } # authorize = ok
(4) Found Auth-Type = eap
(4) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(4) authenticate {
(4) eap: Expiring EAP session with state 0xf2dc3f6df1d82a6f
(4) eap: Finished EAP session with state 0xf2dc3f6df1d82a6f
(4) eap: Previous EAP request found for state 0xf2dc3f6df1d82a6f, released
from the list
(4) eap: Peer sent packet with method EAP TTLS (21)
(4) eap: Calling submodule eap_ttls to process data
(4) eap_ttls: Authenticate
(4) eap_ttls: Continuing EAP-TLS
(4) eap_ttls: Peer ACKed our handshake fragment
(4) eap_ttls: [eaptls verify] = request
(4) eap_ttls: [eaptls process] = handled
(4) eap: Sending EAP Request (code 1) ID 5 length 1004
(4) eap: EAP session adding &reply:State = 0xf2dc3f6df6d92a6f
(4) [eap] = handled
(4) } # authenticate = handled
(4) Using Post-Auth-Type Challenge
(4) Post-Auth-Type sub-section not found. Ignoring.
(4) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(4) Sent Access-Challenge Id 4 from 127.0.0.1:1812 to 127.0.0.1:45118
length 0
(4) EAP-Message =
0x010503ec15c0000012c345af8268dedd66243790299419461925b880d7cbd486286a4470262362a99f866fbfba9070d256778578efea25a917ce50728c003aaae3db63349ff8067101e28220d4fe6fbdb1000578308205743082045ca00302010202102766ee56eb49f38eabd770a2fc84de22300d0609
(4) Message-Authenticator = 0x00000000000000000000000000000000
(4) State = 0xf2dc3f6df6d92a6f134bb1f97963cb4c
(4) Finished request
Waking up in 4.9 seconds.
(5) Received Access-Request Id 5 from 127.0.0.1:45118 to 127.0.0.1:1812
length 149
(5) User-Name = "kerberos-test"
(5) NAS-IP-Address = 127.0.0.1
(5) Calling-Station-Id = "70-6F-6C-69-73-68"
(5) Framed-MTU = 1400
(5) NAS-Port-Type = Wireless-802.11
(5) Service-Type = Framed-User
(5) Connect-Info = "rad_eap_test + eapol_test"
(5) EAP-Message = 0x020500061500
(5) State = 0xf2dc3f6df6d92a6f134bb1f97963cb4c
(5) Message-Authenticator = 0x5c72afabca9c192adbdd0731414aa9df
(5) session-state: No cached attributes
(5) # Executing section authorize from file
/etc/freeradius/3.0/sites-enabled/default
(5) authorize {
(5) policy filter_username {
(5) if (&User-Name) {
(5) if (&User-Name) -> TRUE
(5) if (&User-Name) {
(5) if (&User-Name =~ / /) {
(5) if (&User-Name =~ / /) -> FALSE
(5) if (&User-Name =~ /@[^@]*@/ ) {
(5) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(5) if (&User-Name =~ /\.\./ ) {
(5) if (&User-Name =~ /\.\./ ) -> FALSE
(5) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(5) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) ->
FALSE
(5) if (&User-Name =~ /\.$/) {
(5) if (&User-Name =~ /\.$/) -> FALSE
(5) if (&User-Name =~ /@\./) {
(5) if (&User-Name =~ /@\./) -> FALSE
(5) } # if (&User-Name) = notfound
(5) } # policy filter_username = notfound
(5) [preprocess] = ok
(5) [chap] = noop
(5) [mschap] = noop
(5) [digest] = noop
(5) suffix: Checking for suffix after "@"
(5) suffix: No '@' in User-Name = "kerberos-test", looking up realm NULL
(5) suffix: No such realm "NULL"
(5) [suffix] = noop
(5) eap: Peer sent EAP Response (code 2) ID 5 length 6
(5) eap: Continuing tunnel setup
(5) [eap] = ok
(5) } # authorize = ok
(5) Found Auth-Type = eap
(5) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(5) authenticate {
(5) eap: Expiring EAP session with state 0xf2dc3f6df6d92a6f
(5) eap: Finished EAP session with state 0xf2dc3f6df6d92a6f
(5) eap: Previous EAP request found for state 0xf2dc3f6df6d92a6f, released
from the list
(5) eap: Peer sent packet with method EAP TTLS (21)
(5) eap: Calling submodule eap_ttls to process data
(5) eap_ttls: Authenticate
(5) eap_ttls: Continuing EAP-TLS
(5) eap_ttls: Peer ACKed our handshake fragment
(5) eap_ttls: [eaptls verify] = request
(5) eap_ttls: [eaptls process] = handled
(5) eap: Sending EAP Request (code 1) ID 6 length 837
(5) eap: EAP session adding &reply:State = 0xf2dc3f6df7da2a6f
(5) [eap] = handled
(5) } # authenticate = handled
(5) Using Post-Auth-Type Challenge
(5) Post-Auth-Type sub-section not found. Ignoring.
(5) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(5) Sent Access-Challenge Id 5 from 127.0.0.1:1812 to 127.0.0.1:45118
length 0
(5) EAP-Message =
0x010603451580000012c3551d0e04160414bbaf7e023dfaa6f13c848eadee3898ecd93232d4300e0603551d0f0101ff040403020186300f0603551d130101ff040530030101ff30110603551d20040a300830060604551d200030440603551d1f043d303b3039a037a0358633687474703a2f2f63726c2e
(5) Message-Authenticator = 0x00000000000000000000000000000000
(5) State = 0xf2dc3f6df7da2a6f134bb1f97963cb4c
(5) Finished request
Waking up in 4.9 seconds.
(6) Received Access-Request Id 6 from 127.0.0.1:45118 to 127.0.0.1:1812
length 275
(6) User-Name = "kerberos-test"
(6) NAS-IP-Address = 127.0.0.1
(6) Calling-Station-Id = "70-6F-6C-69-73-68"
(6) Framed-MTU = 1400
(6) NAS-Port-Type = Wireless-802.11
(6) Service-Type = Framed-User
(6) Connect-Info = "rad_eap_test + eapol_test"
(6) EAP-Message =
0x02060084150016030300461000004241047e5df09a07e9f3bb1468a3543afc58a8881b44c0ad915aea0966c7c9cf50761e5359c91bc723eae9530ca756bec3d6db6e450d011c4bfe962c2ab7016f5c58e51403030001011603030028908317fd376e47ace5759a418278f46142cd6c4e019a306a9af268
(6) State = 0xf2dc3f6df7da2a6f134bb1f97963cb4c
(6) Message-Authenticator = 0xb1be710aaf565298b5ac4541c47340c0
(6) session-state: No cached attributes
(6) # Executing section authorize from file
/etc/freeradius/3.0/sites-enabled/default
(6) authorize {
(6) policy filter_username {
(6) if (&User-Name) {
(6) if (&User-Name) -> TRUE
(6) if (&User-Name) {
(6) if (&User-Name =~ / /) {
(6) if (&User-Name =~ / /) -> FALSE
(6) if (&User-Name =~ /@[^@]*@/ ) {
(6) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(6) if (&User-Name =~ /\.\./ ) {
(6) if (&User-Name =~ /\.\./ ) -> FALSE
(6) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(6) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) ->
FALSE
(6) if (&User-Name =~ /\.$/) {
(6) if (&User-Name =~ /\.$/) -> FALSE
(6) if (&User-Name =~ /@\./) {
(6) if (&User-Name =~ /@\./) -> FALSE
(6) } # if (&User-Name) = notfound
(6) } # policy filter_username = notfound
(6) [preprocess] = ok
(6) [chap] = noop
(6) [mschap] = noop
(6) [digest] = noop
(6) suffix: Checking for suffix after "@"
(6) suffix: No '@' in User-Name = "kerberos-test", looking up realm NULL
(6) suffix: No such realm "NULL"
(6) [suffix] = noop
(6) eap: Peer sent EAP Response (code 2) ID 6 length 132
(6) eap: Continuing tunnel setup
(6) [eap] = ok
(6) } # authorize = ok
(6) Found Auth-Type = eap
(6) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(6) authenticate {
(6) eap: Expiring EAP session with state 0xf2dc3f6df7da2a6f
(6) eap: Finished EAP session with state 0xf2dc3f6df7da2a6f
(6) eap: Previous EAP request found for state 0xf2dc3f6df7da2a6f, released
from the list
(6) eap: Peer sent packet with method EAP TTLS (21)
(6) eap: Calling submodule eap_ttls to process data
(6) eap_ttls: Authenticate
(6) eap_ttls: Continuing EAP-TLS
(6) eap_ttls: [eaptls verify] = ok
(6) eap_ttls: Done initial handshake
(6) eap_ttls: <<< recv TLS 1.2 [length 0046]
(6) eap_ttls: TLS_accept: unknown state
(6) eap_ttls: TLS_accept: unknown state
(6) eap_ttls: <<< recv TLS 1.2 [length 0001]
(6) eap_ttls: <<< recv TLS 1.2 [length 0010]
(6) eap_ttls: TLS_accept: unknown state
(6) eap_ttls: >>> send TLS 1.2 [length 0001]
(6) eap_ttls: TLS_accept: unknown state
(6) eap_ttls: >>> send TLS 1.2 [length 0010]
(6) eap_ttls: TLS_accept: unknown state
(6) eap_ttls: TLS_accept: unknown state
(6) eap_ttls: (other): SSL negotiation finished successfully
(6) eap_ttls: SSL Connection Established
(6) eap_ttls: [eaptls process] = handled
(6) eap: Sending EAP Request (code 1) ID 7 length 61
(6) eap: EAP session adding &reply:State = 0xf2dc3f6df4db2a6f
(6) [eap] = handled
(6) } # authenticate = handled
(6) Using Post-Auth-Type Challenge
(6) Post-Auth-Type sub-section not found. Ignoring.
(6) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(6) Sent Access-Challenge Id 6 from 127.0.0.1:1812 to 127.0.0.1:45118
length 0
(6) EAP-Message =
0x0107003d15800000003314030300010116030300280d7a27e7d773017fca61c4b80fb42af7b5012068dea4c7ade8a101595ccd9e8cf9997ebedfc53bc1
(6) Message-Authenticator = 0x00000000000000000000000000000000
(6) State = 0xf2dc3f6df4db2a6f134bb1f97963cb4c
(6) Finished request
Waking up in 4.9 seconds.
(7) Received Access-Request Id 7 from 127.0.0.1:45118 to 127.0.0.1:1812
length 294
(7) User-Name = "kerberos-test"
(7) NAS-IP-Address = 127.0.0.1
(7) Calling-Station-Id = "70-6F-6C-69-73-68"
(7) Framed-MTU = 1400
(7) NAS-Port-Type = Wireless-802.11
(7) Service-Type = Framed-User
(7) Connect-Info = "rad_eap_test + eapol_test"
(7) EAP-Message =
0x020700971500170303008c908317fd376e47ad6d63fa7bd0f61eaf7d094901b479d16c96886b968d4ddac81e67b0bf07402fb9083d6c443755d5ea0fb1e6b8ee5b77f6bccd88f9657d5a8691be73a5b1bad876c014e9ffe1ba1af055aac6e78a3f181f9ccce0419de641da96f364ce0704554e7b8b5611
(7) State = 0xf2dc3f6df4db2a6f134bb1f97963cb4c
(7) Message-Authenticator = 0x527586a6e86987d219527bc2d04d9ab8
(7) session-state: No cached attributes
(7) # Executing section authorize from file
/etc/freeradius/3.0/sites-enabled/default
(7) authorize {
(7) policy filter_username {
(7) if (&User-Name) {
(7) if (&User-Name) -> TRUE
(7) if (&User-Name) {
(7) if (&User-Name =~ / /) {
(7) if (&User-Name =~ / /) -> FALSE
(7) if (&User-Name =~ /@[^@]*@/ ) {
(7) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(7) if (&User-Name =~ /\.\./ ) {
(7) if (&User-Name =~ /\.\./ ) -> FALSE
(7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) ->
FALSE
(7) if (&User-Name =~ /\.$/) {
(7) if (&User-Name =~ /\.$/) -> FALSE
(7) if (&User-Name =~ /@\./) {
(7) if (&User-Name =~ /@\./) -> FALSE
(7) } # if (&User-Name) = notfound
(7) } # policy filter_username = notfound
(7) [preprocess] = ok
(7) [chap] = noop
(7) [mschap] = noop
(7) [digest] = noop
(7) suffix: Checking for suffix after "@"
(7) suffix: No '@' in User-Name = "kerberos-test", looking up realm NULL
(7) suffix: No such realm "NULL"
(7) [suffix] = noop
(7) eap: Peer sent EAP Response (code 2) ID 7 length 151
(7) eap: Continuing tunnel setup
(7) [eap] = ok
(7) } # authorize = ok
(7) Found Auth-Type = eap
(7) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(7) authenticate {
(7) eap: Expiring EAP session with state 0xf2dc3f6df4db2a6f
(7) eap: Finished EAP session with state 0xf2dc3f6df4db2a6f
(7) eap: Previous EAP request found for state 0xf2dc3f6df4db2a6f, released
from the list
(7) eap: Peer sent packet with method EAP TTLS (21)
(7) eap: Calling submodule eap_ttls to process data
(7) eap_ttls: Authenticate
(7) eap_ttls: Continuing EAP-TLS
(7) eap_ttls: [eaptls verify] = ok
(7) eap_ttls: Done initial handshake
(7) eap_ttls: [eaptls process] = ok
(7) eap_ttls: Session established. Proceeding to decode tunneled attributes
(7) eap_ttls: Got tunneled request
(7) eap_ttls: User-Name = "kerberos-test"
(7) eap_ttls: MS-CHAP-Challenge = 0xd4a73ee531a1ca517bd4666353388f89
(7) eap_ttls: MS-CHAP2-Response =
0x4700a84e60c856e3f2cfa4854af16c1e0e5000000000000000004b6334e8b331c0853bc39df4f0f15f5d901418e6bf7f2375
(7) eap_ttls: FreeRADIUS-Proxied-To = 127.0.0.1
(7) eap_ttls: Sending tunneled request
(7) Virtual server inner-tunnel received request
(7) User-Name = "kerberos-test"
(7) MS-CHAP-Challenge = 0xd4a73ee531a1ca517bd4666353388f89
(7) MS-CHAP2-Response =
0x4700a84e60c856e3f2cfa4854af16c1e0e5000000000000000004b6334e8b331c0853bc39df4f0f15f5d901418e6bf7f2375
(7) FreeRADIUS-Proxied-To = 127.0.0.1
(7) NAS-IP-Address = 127.0.0.1
(7) Calling-Station-Id = "70-6F-6C-69-73-68"
(7) Framed-MTU = 1400
(7) NAS-Port-Type = Wireless-802.11
(7) Service-Type = Framed-User
(7) Connect-Info = "rad_eap_test + eapol_test"
(7) Event-Timestamp = "Dec 19 2016 15:23:06 GMT"
(7) WARNING: Outer and inner identities are the same. User privacy is
compromised.
(7) server inner-tunnel {
(7) # Executing section authorize from file
/etc/freeradius/3.0/sites-enabled/inner-tunnel
(7) authorize {
(7) policy filter_username {
(7) if (&User-Name) {
(7) if (&User-Name) -> TRUE
(7) if (&User-Name) {
(7) if (&User-Name =~ / /) {
(7) if (&User-Name =~ / /) -> FALSE
(7) if (&User-Name =~ /@[^@]*@/ ) {
(7) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(7) if (&User-Name =~ /\.\./ ) {
(7) if (&User-Name =~ /\.\./ ) -> FALSE
(7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/))
-> FALSE
(7) if (&User-Name =~ /\.$/) {
(7) if (&User-Name =~ /\.$/) -> FALSE
(7) if (&User-Name =~ /@\./) {
(7) if (&User-Name =~ /@\./) -> FALSE
(7) } # if (&User-Name) = notfound
(7) } # policy filter_username = notfound
(7) [chap] = noop
(7) mschap: Found MS-CHAP attributes. Setting 'Auth-Type = mschap'
(7) [mschap] = ok
(7) suffix: Checking for suffix after "@"
(7) suffix: No '@' in User-Name = "kerberos-test", looking up realm NULL
(7) suffix: No such realm "NULL"
(7) [suffix] = noop
(7) update control {
(7) &Proxy-To-Realm := LOCAL
(7) } # update control = noop
(7) eap: No EAP-Message, not doing EAP
(7) [eap] = noop
(7) update control {
(7) Auth-Type := kerberos
(7) } # update control = noop
(7) [files] = noop
(7) [expiration] = noop
(7) [logintime] = noop
(7) [pap] = noop
(7) } # authorize = ok
(7) Found Auth-Type = kerberos
(7) # Executing group from file
/etc/freeradius/3.0/sites-enabled/inner-tunnel
(7) Auth-Type kerberos {
rlm_krb5 (krb5): Reserved connection (0)
(7) krb5: ERROR: Attribute "User-Password" is required for authentication
rlm_krb5 (krb5): Released connection (0)
rlm_krb5 (krb5): Need 5 more connections to reach 10 spares
rlm_krb5 (krb5): Opening additional connection (5), 1 of 27 pending slots
used
(7) [krb5] = invalid
(7) } # Auth-Type kerberos = invalid
(7) Failed to authenticate the user
(7) Using Post-Auth-Type Reject
(7) # Executing group from file
/etc/freeradius/3.0/sites-enabled/inner-tunnel
(7) Post-Auth-Type REJECT {
(7) attr_filter.access_reject: EXPAND %{User-Name}
(7) attr_filter.access_reject: --> kerberos-test
(7) attr_filter.access_reject: Matched entry DEFAULT at line 11
(7) [attr_filter.access_reject] = updated
(7) update outer.session-state {
(7) &Module-Failure-Message := &request:Module-Failure-Message ->
'krb5: Attribute "User-Password" is required for authentication'
(7) } # update outer.session-state = noop
(7) } # Post-Auth-Type REJECT = updated
(7) } # server inner-tunnel
(7) Virtual server sending reply
(7) eap_ttls: Got tunneled Access-Reject
(7) eap: ERROR: Failed continuing EAP TTLS (21) session. EAP sub-module
failed
(7) eap: Sending EAP Failure (code 4) ID 7 length 4
(7) eap: Failed in EAP select
(7) [eap] = invalid
(7) } # authenticate = invalid
(7) Failed to authenticate the user
(7) Using Post-Auth-Type Reject
(7) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(7) Post-Auth-Type REJECT {
(7) attr_filter.access_reject: EXPAND %{User-Name}
(7) attr_filter.access_reject: --> kerberos-test
(7) attr_filter.access_reject: Matched entry DEFAULT at line 11
(7) [attr_filter.access_reject] = updated
(7) [eap] = noop
(7) policy remove_reply_message_if_eap {
(7) if (&reply:EAP-Message && &reply:Reply-Message) {
(7) if (&reply:EAP-Message && &reply:Reply-Message) -> FALSE
(7) else {
(7) [noop] = noop
(7) } # else = noop
(7) } # policy remove_reply_message_if_eap = noop
(7) } # Post-Auth-Type REJECT = updated
(7) Delaying response for 1.000000 seconds
Waking up in 0.3 seconds.
Waking up in 0.6 seconds.
(7) Sending delayed response
(7) Sent Access-Reject Id 7 from 127.0.0.1:1812 to 127.0.0.1:45118 length 44
(7) EAP-Message = 0x04070004
(7) Message-Authenticator = 0x00000000000000000000000000000000
Waking up in 3.9 seconds.
--
--
More information about the Freeradius-Users
mailing list