eap auth not working for realm database users
Guido Kostons
freeradius12345 at outlook.com
Sun Sep 1 15:20:52 CEST 2019
What you are trying to do:
I setup my home wifi hobby project based on this tutorial: https://codebeta.com/unifi-with-freeradius-part-1-setup-radius-with-mariadb-mysql-7b368d4f1f15
This works very nice with dynamic vlans and everything. The next step is to roam my laptop/mobile phone between my location and a friends house. For us this is a learning hobby project.
Why you are trying to do it:
To make a roaming ssid between my location and the house of a friend.
I added a test realm to proxy.conf
realm somedomain.tld {
}
Wen I test to authenticate with eapol_test with test at somedomain.tld it does not work if i test again without the realm part the user does authenticate then it does work.
Last 2 weeks I read a lot about it, I read the comments in the configuration files again and again, I read most of the freeradius documentation because I didn't want to ask nobody for help. I read many mailing list posts. I tested numerous things but all comes down to the same problem over and over again.
I setup a fresh new install of freeradius, because that was advised in some of the mailinglist posts, on a clean new Debian 10 Buster vm. Added the realm into proxy.conf and created a testuser in the users file and everything works with and without using the realm in the logins with eapol_test. Great thit is what I want but then with my database users.
The moment I start implementing the things of this tutorial (https://codebeta.com/unifi-with-freeradius-part-1-setup-radius-with-mariadb-mysql-7b368d4f1f15) again things start to get wrong after I use the database users. Whitout the realm part in the username I can authenticate, with the realm in the username I can't authenticate.
What you expect the server to do:
What I would like the server to do, besides what is in the tutorial above, is that the database users authenticate with and without the realm in the username. And eventually i want another realm of the domain of my friend to proxy his user logins to his freeradius. So we can roam our laptops and mobile phones between our locations.
Wen I use eapol_test with a database testuser without the realm in the username auth works. Wen I add the realm to the username auth doesn't work anymore.
I also tested with nostrip in the local realm that didn't worked either. I think the nostrip is only needed in the realm of the proxy-ed radius server to my friends house. I will add this part later because I want first solve this local realm problem.
What the server does instead:
FreeRADIUS Version 3.0.17
Copyright (C) 1999-2017 The FreeRADIUS server project and contributors
There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A
PARTICULAR PURPOSE
You may redistribute copies of FreeRADIUS under the terms of the
GNU General Public License
For more information about these matters, see the file named COPYRIGHT
Starting - reading configuration files ...
including dictionary file /usr/share/freeradius/dictionary
including dictionary file /usr/share/freeradius/dictionary.dhcp
including dictionary file /usr/share/freeradius/dictionary.vqp
including dictionary file /etc/freeradius/3.0/dictionary
including configuration file /etc/freeradius/3.0/radiusd.conf
including configuration file /etc/freeradius/3.0/proxy.conf
including files in directory /etc/freeradius/3.0/mods-enabled/
including configuration file /etc/freeradius/3.0/mods-enabled/files
including configuration file /etc/freeradius/3.0/mods-enabled/sradutmp
including configuration file /etc/freeradius/3.0/mods-enabled/replicate
including configuration file /etc/freeradius/3.0/mods-enabled/eap
including configuration file /etc/freeradius/3.0/mods-enabled/logintime
including configuration file /etc/freeradius/3.0/mods-enabled/attr_filter
including configuration file /etc/freeradius/3.0/mods-enabled/detail
including configuration file /etc/freeradius/3.0/mods-enabled/sql
including configuration file /etc/freeradius/3.0/mods-config/sql/main/mysql/queries.conf
including configuration file /etc/freeradius/3.0/mods-enabled/always
including configuration file /etc/freeradius/3.0/mods-enabled/unpack
including configuration file /etc/freeradius/3.0/mods-enabled/detail.log
including configuration file /etc/freeradius/3.0/mods-enabled/unix
including configuration file /etc/freeradius/3.0/mods-enabled/expiration
including configuration file /etc/freeradius/3.0/mods-enabled/exec
including configuration file /etc/freeradius/3.0/mods-enabled/expr
including configuration file /etc/freeradius/3.0/mods-enabled/pap
including configuration file /etc/freeradius/3.0/mods-enabled/soh
including configuration file /etc/freeradius/3.0/mods-enabled/utf8
including configuration file /etc/freeradius/3.0/mods-enabled/linelog
including configuration file /etc/freeradius/3.0/mods-enabled/chap
including configuration file /etc/freeradius/3.0/mods-enabled/cache_eap
including configuration file /etc/freeradius/3.0/mods-enabled/radutmp
including configuration file /etc/freeradius/3.0/mods-enabled/dynamic_clients
including configuration file /etc/freeradius/3.0/mods-enabled/preprocess
including configuration file /etc/freeradius/3.0/mods-enabled/echo
including configuration file /etc/freeradius/3.0/mods-enabled/passwd
including configuration file /etc/freeradius/3.0/mods-enabled/digest
including configuration file /etc/freeradius/3.0/mods-enabled/mschap
including configuration file /etc/freeradius/3.0/mods-enabled/ntlm_auth
including configuration file /etc/freeradius/3.0/mods-enabled/realm
including files in directory /etc/freeradius/3.0/policy.d/
including configuration file /etc/freeradius/3.0/policy.d/debug
including configuration file /etc/freeradius/3.0/policy.d/cui
including configuration file /etc/freeradius/3.0/policy.d/eap
including configuration file /etc/freeradius/3.0/policy.d/canonicalization
including configuration file /etc/freeradius/3.0/policy.d/control
including configuration file /etc/freeradius/3.0/policy.d/abfab-tr
including configuration file /etc/freeradius/3.0/policy.d/operator-name
including configuration file /etc/freeradius/3.0/policy.d/moonshot-targeted-ids
including configuration file /etc/freeradius/3.0/policy.d/filter
including configuration file /etc/freeradius/3.0/policy.d/accounting
including configuration file /etc/freeradius/3.0/policy.d/dhcp
including files in directory /etc/freeradius/3.0/sites-enabled/
including configuration file /etc/freeradius/3.0/sites-enabled/inner-tunnel
including configuration file /etc/freeradius/3.0/sites-enabled/default
main {
security {
user = "freerad"
group = "freerad"
allow_core_dumps = no
}
name = "freeradius"
prefix = "/usr"
localstatedir = "/var"
logdir = "/var/log/freeradius"
run_dir = "/var/run/freeradius"
}
main {
name = "freeradius"
prefix = "/usr"
localstatedir = "/var"
sbindir = "/usr/sbin"
logdir = "/var/log/freeradius"
run_dir = "/var/run/freeradius"
libdir = "/usr/lib/freeradius"
radacctdir = "/var/log/freeradius/radacct"
hostname_lookups = no
max_request_time = 30
cleanup_delay = 5
max_requests = 16384
pidfile = "/var/run/freeradius/freeradius.pid"
checkrad = "/usr/sbin/checkrad"
debug_level = 0
proxy_requests = yes
log {
stripped_names = no
auth = no
auth_badpass = no
auth_goodpass = no
colourise = yes
msg_denied = "You are already logged in - access denied"
}
resources {
}
security {
max_attributes = 200
reject_delay = 1.000000
status_server = yes
}
}
radiusd: #### Loading Realms and Home Servers ####
proxy server {
retry_delay = 5
retry_count = 3
default_fallback = no
dead_time = 120
wake_all_if_all_dead = no
}
home_server localhost {
ipaddr = 127.0.0.1
port = 1812
type = "auth"
secret = <<< secret >>>
response_window = 20.000000
response_timeouts = 1
max_outstanding = 65536
zombie_period = 40
status_check = "status-server"
ping_interval = 30
check_interval = 30
check_timeout = 4
num_answers_to_alive = 3
revive_interval = 120
limit {
max_connections = 16
max_requests = 0
lifetime = 0
idle_timeout = 0
}
coa {
irt = 2
mrt = 16
mrc = 5
mrd = 30
}
}
realm somedomain.tld {
}
home_server_pool my_auth_failover {
type = fail-over
home_server = localhost
}
realm example.com {
auth_pool = my_auth_failover
}
realm LOCAL {
}
radiusd: #### Loading Clients ####
Debugger not attached
# Creating Auth-Type = mschap
# Creating Auth-Type = eap
# Creating Auth-Type = PAP
# Creating Auth-Type = MS-CHAP
# Creating Auth-Type = digest
radiusd: #### Instantiating modules ####
modules {
# Loaded module rlm_files
# Loading module "files" from file /etc/freeradius/3.0/mods-enabled/files
files {
filename = "/etc/freeradius/3.0/mods-config/files/authorize"
acctusersfile = "/etc/freeradius/3.0/mods-config/files/accounting"
preproxy_usersfile = "/etc/freeradius/3.0/mods-config/files/pre-proxy"
}
# Loaded module rlm_radutmp
# Loading module "sradutmp" from file /etc/freeradius/3.0/mods-enabled/sradutmp
radutmp sradutmp {
filename = "/var/log/freeradius/sradutmp"
username = "%{User-Name}"
case_sensitive = yes
check_with_nas = yes
permissions = 420
caller_id = no
}
# Loaded module rlm_replicate
# Loading module "replicate" from file /etc/freeradius/3.0/mods-enabled/replicate
# Loaded module rlm_eap
# Loading module "eap" from file /etc/freeradius/3.0/mods-enabled/eap
eap {
default_eap_type = "md5"
timer_expire = 60
ignore_unknown_eap_types = no
cisco_accounting_username_bug = no
max_sessions = 16384
}
# Loaded module rlm_logintime
# Loading module "logintime" from file /etc/freeradius/3.0/mods-enabled/logintime
logintime {
minimum_timeout = 60
}
# Loaded module rlm_attr_filter
# Loading module "attr_filter.post-proxy" from file /etc/freeradius/3.0/mods-enabled/attr_filter
attr_filter attr_filter.post-proxy {
filename = "/etc/freeradius/3.0/mods-config/attr_filter/post-proxy"
key = "%{Realm}"
relaxed = no
}
# Loading module "attr_filter.pre-proxy" from file /etc/freeradius/3.0/mods-enabled/attr_filter
attr_filter attr_filter.pre-proxy {
filename = "/etc/freeradius/3.0/mods-config/attr_filter/pre-proxy"
key = "%{Realm}"
relaxed = no
}
# Loading module "attr_filter.access_reject" from file /etc/freeradius/3.0/mods-enabled/attr_filter
attr_filter attr_filter.access_reject {
filename = "/etc/freeradius/3.0/mods-config/attr_filter/access_reject"
key = "%{User-Name}"
relaxed = no
}
# Loading module "attr_filter.access_challenge" from file /etc/freeradius/3.0/mods-enabled/attr_filter
attr_filter attr_filter.access_challenge {
filename = "/etc/freeradius/3.0/mods-config/attr_filter/access_challenge"
key = "%{User-Name}"
relaxed = no
}
# Loading module "attr_filter.accounting_response" from file /etc/freeradius/3.0/mods-enabled/attr_filter
attr_filter attr_filter.accounting_response {
filename = "/etc/freeradius/3.0/mods-config/attr_filter/accounting_response"
key = "%{User-Name}"
relaxed = no
}
# Loaded module rlm_detail
# Loading module "detail" from file /etc/freeradius/3.0/mods-enabled/detail
detail {
filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/detail-%Y%m%d"
header = "%t"
permissions = 384
locking = no
escape_filenames = no
log_packet_header = no
}
# Loaded module rlm_sql
# Loading module "sql" from file /etc/freeradius/3.0/mods-enabled/sql
sql {
driver = "rlm_sql_mysql"
server = "localhost"
port = 3306
login = "radius"
password = <<< secret >>>
radius_db = "radius"
read_groups = yes
read_profiles = yes
read_clients = yes
delete_stale_sessions = yes
sql_user_name = "%{User-Name}"
default_user_profile = ""
client_query = "SELECT id, nasname, shortname, type, secret, server FROM nas"
authorize_check_query = "SELECT id, username, attribute, value, op FROM radcheck WHERE username = '%{SQL-User-Name}' ORDER BY id"
authorize_reply_query = "SELECT id, username, attribute, value, op FROM radreply WHERE username = '%{SQL-User-Name}' ORDER BY id"
authorize_group_check_query = "SELECT id, groupname, attribute, Value, op FROM radgroupcheck WHERE groupname = '%{SQL-Group}' ORDER BY id"
authorize_group_reply_query = "SELECT id, groupname, attribute, value, op FROM radgroupreply WHERE groupname = '%{SQL-Group}' ORDER BY id"
group_membership_query = "SELECT groupname FROM radusergroup WHERE username = '%{SQL-User-Name}' ORDER BY priority"
simul_count_query = "SELECT COUNT(*) FROM radacct WHERE username = '%{SQL-User-Name}' AND acctstoptime IS NULL"
simul_verify_query = "SELECT radacctid, acctsessionid, username, nasipaddress, nasportid, framedipaddress, callingstationid, framedprotocol FROM radacct WHERE username = '%{SQL-User-Name}' AND acctstoptime IS NULL"
safe_characters = "@abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789.-_: /"
accounting {
reference = "%{tolower:type.%{Acct-Status-Type}.query}"
type {
accounting-on {
query = "UPDATE radacct SET acctstoptime = FROM_UNIXTIME(%{integer:Event-Timestamp}), acctsessiontime = '%{integer:Event-Timestamp}' - UNIX_TIMESTAMP(acctstarttime), acctterminatecause = '%{%{Acct-Terminate-Cause}:-NAS-Reboot}' WHERE acctstoptime IS NULL AND nasipaddress = '%{NAS-IP-Address}' AND acctstarttime <= FROM_UNIXTIME(%{integer:Event-Timestamp})"
}
accounting-off {
query = "UPDATE radacct SET acctstoptime = FROM_UNIXTIME(%{integer:Event-Timestamp}), acctsessiontime = '%{integer:Event-Timestamp}' - UNIX_TIMESTAMP(acctstarttime), acctterminatecause = '%{%{Acct-Terminate-Cause}:-NAS-Reboot}' WHERE acctstoptime IS NULL AND nasipaddress = '%{NAS-IP-Address}' AND acctstarttime <= FROM_UNIXTIME(%{integer:Event-Timestamp})"
}
start {
query = "INSERT INTO radacct (acctsessionid, acctuniqueid, username, realm, nasipaddress, nasportid, nasporttype, acctstarttime, acctupdatetime, acctstoptime, acctsessiontime, acctauthentic, connectinfo_start, connectinfo_stop, acctinputoctets, acctoutputoctets, calledstationid, callingstationid, acctterminatecause, servicetype, framedprotocol, framedipaddress) VALUES ('%{Acct-Session-Id}', '%{Acct-Unique-Session-Id}', '%{SQL-User-Name}', '%{Realm}', '%{NAS-IP-Address}', '%{%{NAS-Port-ID}:-%{NAS-Port}}', '%{NAS-Port-Type}', FROM_UNIXTIME(%{integer:Event-Timestamp}), FROM_UNIXTIME(%{integer:Event-Timestamp}), NULL, '0', '%{Acct-Authentic}', '%{Connect-Info}', '', '0', '0', '%{Called-Station-Id}', '%{Calling-Station-Id}', '', '%{Service-Type}', '%{Framed-Protocol}', '%{Framed-IP-Address}')"
}
interim-update {
query = "UPDATE radacct SET acctupdatetime = (@acctupdatetime_old:=acctupdatetime), acctupdatetime = FROM_UNIXTIME(%{integer:Event-Timestamp}), acctinterval = %{integer:Event-Timestamp} - UNIX_TIMESTAMP(@acctupdatetime_old), framedipaddress = '%{Framed-IP-Address}', acctsessiontime = %{%{Acct-Session-Time}:-NULL}, acctinputoctets = '%{%{Acct-Input-Gigawords}:-0}' << 32 | '%{%{Acct-Input-Octets}:-0}', acctoutputoctets = '%{%{Acct-Output-Gigawords}:-0}' << 32 | '%{%{Acct-Output-Octets}:-0}' WHERE AcctUniqueId = '%{Acct-Unique-Session-Id}'"
}
stop {
query = "UPDATE radacct SET acctstoptime = FROM_UNIXTIME(%{integer:Event-Timestamp}), acctsessiontime = %{%{Acct-Session-Time}:-NULL}, acctinputoctets = '%{%{Acct-Input-Gigawords}:-0}' << 32 | '%{%{Acct-Input-Octets}:-0}', acctoutputoctets = '%{%{Acct-Output-Gigawords}:-0}' << 32 | '%{%{Acct-Output-Octets}:-0}', acctterminatecause = '%{Acct-Terminate-Cause}', connectinfo_stop = '%{Connect-Info}' WHERE AcctUniqueId = '%{Acct-Unique-Session-Id}'"
}
}
}
post-auth {
reference = ".query"
query = "INSERT INTO radpostauth (username, pass, reply, authdate) VALUES ( '%{SQL-User-Name}', '%{%{User-Password}:-%{Chap-Password}}', '%{reply:Packet-Type}', '%S')"
}
}
rlm_sql (sql): Driver rlm_sql_mysql (module rlm_sql_mysql) loaded and linked
Creating attribute SQL-Group
# Loaded module rlm_always
# Loading module "reject" from file /etc/freeradius/3.0/mods-enabled/always
always reject {
rcode = "reject"
simulcount = 0
mpp = no
}
# Loading module "fail" from file /etc/freeradius/3.0/mods-enabled/always
always fail {
rcode = "fail"
simulcount = 0
mpp = no
}
# Loading module "ok" from file /etc/freeradius/3.0/mods-enabled/always
always ok {
rcode = "ok"
simulcount = 0
mpp = no
}
# Loading module "handled" from file /etc/freeradius/3.0/mods-enabled/always
always handled {
rcode = "handled"
simulcount = 0
mpp = no
}
# Loading module "invalid" from file /etc/freeradius/3.0/mods-enabled/always
always invalid {
rcode = "invalid"
simulcount = 0
mpp = no
}
# Loading module "userlock" from file /etc/freeradius/3.0/mods-enabled/always
always userlock {
rcode = "userlock"
simulcount = 0
mpp = no
}
# Loading module "notfound" from file /etc/freeradius/3.0/mods-enabled/always
always notfound {
rcode = "notfound"
simulcount = 0
mpp = no
}
# Loading module "noop" from file /etc/freeradius/3.0/mods-enabled/always
always noop {
rcode = "noop"
simulcount = 0
mpp = no
}
# Loading module "updated" from file /etc/freeradius/3.0/mods-enabled/always
always updated {
rcode = "updated"
simulcount = 0
mpp = no
}
# Loaded module rlm_unpack
# Loading module "unpack" from file /etc/freeradius/3.0/mods-enabled/unpack
# Loading module "auth_log" from file /etc/freeradius/3.0/mods-enabled/detail.log
detail auth_log {
filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d"
header = "%t"
permissions = 384
locking = no
escape_filenames = no
log_packet_header = no
}
# Loading module "reply_log" from file /etc/freeradius/3.0/mods-enabled/detail.log
detail reply_log {
filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/reply-detail-%Y%m%d"
header = "%t"
permissions = 384
locking = no
escape_filenames = no
log_packet_header = no
}
# Loading module "pre_proxy_log" from file /etc/freeradius/3.0/mods-enabled/detail.log
detail pre_proxy_log {
filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/pre-proxy-detail-%Y%m%d"
header = "%t"
permissions = 384
locking = no
escape_filenames = no
log_packet_header = no
}
# Loading module "post_proxy_log" from file /etc/freeradius/3.0/mods-enabled/detail.log
detail post_proxy_log {
filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/post-proxy-detail-%Y%m%d"
header = "%t"
permissions = 384
locking = no
escape_filenames = no
log_packet_header = no
}
# Loaded module rlm_unix
# Loading module "unix" from file /etc/freeradius/3.0/mods-enabled/unix
unix {
radwtmp = "/var/log/freeradius/radwtmp"
}
Creating attribute Unix-Group
# Loaded module rlm_expiration
# Loading module "expiration" from file /etc/freeradius/3.0/mods-enabled/expiration
# Loaded module rlm_exec
# Loading module "exec" from file /etc/freeradius/3.0/mods-enabled/exec
exec {
wait = no
input_pairs = "request"
shell_escape = yes
timeout = 10
}
# Loaded module rlm_expr
# Loading module "expr" from file /etc/freeradius/3.0/mods-enabled/expr
expr {
safe_characters = "@abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789.-_: /äéöüàâæçèéêëîïôœùûüaÿÄÉÖÜßÀÂÆÇÈÉÊËÎÏÔŒÙÛÜŸ"
}
# Loaded module rlm_pap
# Loading module "pap" from file /etc/freeradius/3.0/mods-enabled/pap
pap {
normalise = yes
}
# Loaded module rlm_soh
# Loading module "soh" from file /etc/freeradius/3.0/mods-enabled/soh
soh {
dhcp = yes
}
# Loaded module rlm_utf8
# Loading module "utf8" from file /etc/freeradius/3.0/mods-enabled/utf8
# Loaded module rlm_linelog
# Loading module "linelog" from file /etc/freeradius/3.0/mods-enabled/linelog
linelog {
filename = "/var/log/freeradius/linelog"
escape_filenames = no
syslog_severity = "info"
permissions = 384
format = "This is a log message for %{User-Name}"
reference = "messages.%{%{reply:Packet-Type}:-default}"
}
# Loading module "log_accounting" from file /etc/freeradius/3.0/mods-enabled/linelog
linelog log_accounting {
filename = "/var/log/freeradius/linelog-accounting"
escape_filenames = no
syslog_severity = "info"
permissions = 384
format = ""
reference = "Accounting-Request.%{%{Acct-Status-Type}:-unknown}"
}
# Loaded module rlm_chap
# Loading module "chap" from file /etc/freeradius/3.0/mods-enabled/chap
# Loaded module rlm_cache
# Loading module "cache_eap" from file /etc/freeradius/3.0/mods-enabled/cache_eap
cache cache_eap {
driver = "rlm_cache_rbtree"
key = "%{%{control:State}:-%{%{reply:State}:-%{State}}}"
ttl = 15
max_entries = 0
epoch = 0
add_stats = no
}
# Loading module "radutmp" from file /etc/freeradius/3.0/mods-enabled/radutmp
radutmp {
filename = "/var/log/freeradius/radutmp"
username = "%{User-Name}"
case_sensitive = yes
check_with_nas = yes
permissions = 384
caller_id = yes
}
# Loaded module rlm_dynamic_clients
# Loading module "dynamic_clients" from file /etc/freeradius/3.0/mods-enabled/dynamic_clients
# Loaded module rlm_preprocess
# Loading module "preprocess" from file /etc/freeradius/3.0/mods-enabled/preprocess
preprocess {
huntgroups = "/etc/freeradius/3.0/mods-config/preprocess/huntgroups"
hints = "/etc/freeradius/3.0/mods-config/preprocess/hints"
with_ascend_hack = no
ascend_channels_per_line = 23
with_ntdomain_hack = no
with_specialix_jetstream_hack = no
with_cisco_vsa_hack = no
with_alvarion_vsa_hack = no
}
# Loading module "echo" from file /etc/freeradius/3.0/mods-enabled/echo
exec echo {
wait = yes
program = "/bin/echo %{User-Name}"
input_pairs = "request"
output_pairs = "reply"
shell_escape = yes
}
# Loaded module rlm_passwd
# Loading module "etc_passwd" from file /etc/freeradius/3.0/mods-enabled/passwd
passwd etc_passwd {
filename = "/etc/passwd"
format = "*User-Name:Crypt-Password:"
delimiter = ":"
ignore_nislike = no
ignore_empty = yes
allow_multiple_keys = no
hash_size = 100
}
# Loaded module rlm_digest
# Loading module "digest" from file /etc/freeradius/3.0/mods-enabled/digest
# Loaded module rlm_mschap
# Loading module "mschap" from file /etc/freeradius/3.0/mods-enabled/mschap
mschap {
use_mppe = yes
require_encryption = no
require_strong = no
with_ntdomain_hack = yes
passchange {
}
allow_retry = yes
winbind_retry_with_normalised_username = no
}
# Loading module "ntlm_auth" from file /etc/freeradius/3.0/mods-enabled/ntlm_auth
exec ntlm_auth {
wait = yes
program = "/path/to/ntlm_auth --request-nt-key --domain=MYDOMAIN --username=%{mschap:User-Name} --password=%{User-Password}"
shell_escape = yes
}
# Loaded module rlm_realm
# Loading module "IPASS" from file /etc/freeradius/3.0/mods-enabled/realm
realm IPASS {
format = "prefix"
delimiter = "/"
ignore_default = no
ignore_null = no
}
# Loading module "suffix" from file /etc/freeradius/3.0/mods-enabled/realm
realm suffix {
format = "suffix"
delimiter = "@"
ignore_default = no
ignore_null = no
}
# Loading module "realmpercent" from file /etc/freeradius/3.0/mods-enabled/realm
realm realmpercent {
format = "suffix"
delimiter = "%"
ignore_default = no
ignore_null = no
}
# Loading module "ntdomain" from file /etc/freeradius/3.0/mods-enabled/realm
realm ntdomain {
format = "prefix"
delimiter = "\\"
ignore_default = no
ignore_null = no
}
instantiate {
}
# Instantiating module "files" from file /etc/freeradius/3.0/mods-enabled/files
reading pairlist file /etc/freeradius/3.0/mods-config/files/authorize
reading pairlist file /etc/freeradius/3.0/mods-config/files/accounting
reading pairlist file /etc/freeradius/3.0/mods-config/files/pre-proxy
# Instantiating module "eap" from file /etc/freeradius/3.0/mods-enabled/eap
# Linked to sub-module rlm_eap_md5
# Linked to sub-module rlm_eap_leap
# Linked to sub-module rlm_eap_gtc
gtc {
challenge = "Password: "
auth_type = "PAP"
}
# Linked to sub-module rlm_eap_tls
tls {
tls = "tls-common"
}
tls-config tls-common {
verify_depth = 0
ca_path = "/etc/freeradius/3.0/certs"
pem_file_type = yes
private_key_file = "/etc/ssl/private/ssl-cert-snakeoil.key"
certificate_file = "/etc/ssl/certs/ssl-cert-snakeoil.pem"
ca_file = "/etc/ssl/certs/ca-certificates.crt"
private_key_password = <<< secret >>>
dh_file = "/etc/freeradius/3.0/certs/dh"
fragment_size = 1024
include_length = yes
auto_chain = yes
check_crl = no
check_all_crl = no
cipher_list = "DEFAULT"
cipher_server_preference = no
ecdh_curve = "prime256v1"
tls_max_version = ""
tls_min_version = "1.0"
cache {
enable = no
lifetime = 24
max_entries = 255
}
verify {
skip_if_ocsp_ok = no
}
ocsp {
enable = no
override_cert_url = yes
url = "http://127.0.0.1/ocsp/"
use_nonce = yes
timeout = 0
softfail = no
}
}
# Linked to sub-module rlm_eap_ttls
ttls {
tls = "tls-common"
default_eap_type = "md5"
copy_request_to_tunnel = no
use_tunneled_reply = no
virtual_server = "inner-tunnel"
include_length = yes
require_client_cert = no
}
tls: Using cached TLS configuration from previous invocation
# Linked to sub-module rlm_eap_peap
peap {
tls = "tls-common"
default_eap_type = "mschapv2"
copy_request_to_tunnel = no
use_tunneled_reply = no
proxy_tunneled_request_as_eap = yes
virtual_server = "inner-tunnel"
soh = no
require_client_cert = no
}
tls: Using cached TLS configuration from previous invocation
# Linked to sub-module rlm_eap_mschapv2
mschapv2 {
with_ntdomain_hack = no
send_error = no
}
# Instantiating module "logintime" from file /etc/freeradius/3.0/mods-enabled/logintime
# Instantiating module "attr_filter.post-proxy" from file /etc/freeradius/3.0/mods-enabled/attr_filter
reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/post-proxy
# Instantiating module "attr_filter.pre-proxy" from file /etc/freeradius/3.0/mods-enabled/attr_filter
reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/pre-proxy
# Instantiating module "attr_filter.access_reject" from file /etc/freeradius/3.0/mods-enabled/attr_filter
reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/access_reject
[/etc/freeradius/3.0/mods-config/attr_filter/access_reject]:11 Check item "FreeRADIUS-Response-Delay" found in filter list for realm "DEFAULT".
[/etc/freeradius/3.0/mods-config/attr_filter/access_reject]:11 Check item "FreeRADIUS-Response-Delay-USec" found in filter list for realm "DEFAULT".
# Instantiating module "attr_filter.access_challenge" from file /etc/freeradius/3.0/mods-enabled/attr_filter
reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/access_challenge
# Instantiating module "attr_filter.accounting_response" from file /etc/freeradius/3.0/mods-enabled/attr_filter
reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/accounting_response
# Instantiating module "detail" from file /etc/freeradius/3.0/mods-enabled/detail
# Instantiating module "sql" from file /etc/freeradius/3.0/mods-enabled/sql
rlm_sql_mysql: libmysql version: 10.3.15
mysql {
tls {
}
warnings = "auto"
}
rlm_sql (sql): Attempting to connect to database "radius"
rlm_sql (sql): Initialising connection pool
pool {
start = 5
min = 3
max = 32
spare = 10
uses = 0
lifetime = 0
cleanup_interval = 30
idle_timeout = 60
retry_delay = 30
spread = no
}
rlm_sql (sql): Opening additional connection (0), 1 of 32 pending slots used
rlm_sql_mysql: Starting connect to MySQL server
rlm_sql_mysql: Connected to database 'radius' on Localhost via UNIX socket, server version 10.3.15-MariaDB-1, protocol version 10
rlm_sql (sql): Opening additional connection (1), 1 of 31 pending slots used
rlm_sql_mysql: Starting connect to MySQL server
rlm_sql_mysql: Connected to database 'radius' on Localhost via UNIX socket, server version 10.3.15-MariaDB-1, protocol version 10
rlm_sql (sql): Opening additional connection (2), 1 of 30 pending slots used
rlm_sql_mysql: Starting connect to MySQL server
rlm_sql_mysql: Connected to database 'radius' on Localhost via UNIX socket, server version 10.3.15-MariaDB-1, protocol version 10
rlm_sql (sql): Opening additional connection (3), 1 of 29 pending slots used
rlm_sql_mysql: Starting connect to MySQL server
rlm_sql_mysql: Connected to database 'radius' on Localhost via UNIX socket, server version 10.3.15-MariaDB-1, protocol version 10
rlm_sql (sql): Opening additional connection (4), 1 of 28 pending slots used
rlm_sql_mysql: Starting connect to MySQL server
rlm_sql_mysql: Connected to database 'radius' on Localhost via UNIX socket, server version 10.3.15-MariaDB-1, protocol version 10
rlm_sql (sql): Processing generate_sql_clients
rlm_sql (sql) in generate_sql_clients: query is SELECT id, nasname, shortname, type, secret, server FROM nas
rlm_sql (sql): Reserved connection (0)
rlm_sql (sql): Executing select query: SELECT id, nasname, shortname, type, secret, server FROM nas
rlm_sql (sql): Adding client 192.168.162.1 (def-router) to global clients list
rlm_sql (192.168.162.1): Client "def-router" (sql) added
rlm_sql (sql): Adding client 192.168.162.7 (AP2) to global clients list
rlm_sql (192.168.162.7): Client "AP2" (sql) added
rlm_sql (sql): Adding client 192.168.162.8 (AP3) to global clients list
rlm_sql (192.168.162.8): Client "AP3" (sql) added
rlm_sql (sql): Adding client 192.168.166.1 (dmz-router) to global clients list
rlm_sql (192.168.166.1): Client "dmz-router" (sql) added
rlm_sql (sql): Adding client 192.168.166.26 (radius4) to global clients list
rlm_sql (192.168.166.26): Client "radius4" (sql) added
rlm_sql (sql): Adding client 127.0.0.1 (localhost) to global clients list
rlm_sql (127.0.0.1): Client "localhost" (sql) added
rlm_sql (sql): Released connection (0)
Need 5 more connections to reach 10 spares
rlm_sql (sql): Opening additional connection (5), 1 of 27 pending slots used
rlm_sql_mysql: Starting connect to MySQL server
rlm_sql_mysql: Connected to database 'radius' on Localhost via UNIX socket, server version 10.3.15-MariaDB-1, protocol version 10
# Instantiating module "reject" from file /etc/freeradius/3.0/mods-enabled/always
# Instantiating module "fail" from file /etc/freeradius/3.0/mods-enabled/always
# Instantiating module "ok" from file /etc/freeradius/3.0/mods-enabled/always
# Instantiating module "handled" from file /etc/freeradius/3.0/mods-enabled/always
# Instantiating module "invalid" from file /etc/freeradius/3.0/mods-enabled/always
# Instantiating module "userlock" from file /etc/freeradius/3.0/mods-enabled/always
# Instantiating module "notfound" from file /etc/freeradius/3.0/mods-enabled/always
# Instantiating module "noop" from file /etc/freeradius/3.0/mods-enabled/always
# Instantiating module "updated" from file /etc/freeradius/3.0/mods-enabled/always
# Instantiating module "auth_log" from file /etc/freeradius/3.0/mods-enabled/detail.log
rlm_detail (auth_log): 'User-Password' suppressed, will not appear in detail output
# Instantiating module "reply_log" from file /etc/freeradius/3.0/mods-enabled/detail.log
# Instantiating module "pre_proxy_log" from file /etc/freeradius/3.0/mods-enabled/detail.log
# Instantiating module "post_proxy_log" from file /etc/freeradius/3.0/mods-enabled/detail.log
# Instantiating module "expiration" from file /etc/freeradius/3.0/mods-enabled/expiration
# Instantiating module "pap" from file /etc/freeradius/3.0/mods-enabled/pap
# Instantiating module "linelog" from file /etc/freeradius/3.0/mods-enabled/linelog
# Instantiating module "log_accounting" from file /etc/freeradius/3.0/mods-enabled/linelog
# Instantiating module "cache_eap" from file /etc/freeradius/3.0/mods-enabled/cache_eap
rlm_cache (cache_eap): Driver rlm_cache_rbtree (module rlm_cache_rbtree) loaded and linked
# Instantiating module "preprocess" from file /etc/freeradius/3.0/mods-enabled/preprocess
reading pairlist file /etc/freeradius/3.0/mods-config/preprocess/huntgroups
reading pairlist file /etc/freeradius/3.0/mods-config/preprocess/hints
# Instantiating module "etc_passwd" from file /etc/freeradius/3.0/mods-enabled/passwd
rlm_passwd: nfields: 3 keyfield 0(User-Name) listable: no
# Instantiating module "mschap" from file /etc/freeradius/3.0/mods-enabled/mschap
rlm_mschap (mschap): using internal authentication
# Instantiating module "IPASS" from file /etc/freeradius/3.0/mods-enabled/realm
# Instantiating module "suffix" from file /etc/freeradius/3.0/mods-enabled/realm
# Instantiating module "realmpercent" from file /etc/freeradius/3.0/mods-enabled/realm
# Instantiating module "ntdomain" from file /etc/freeradius/3.0/mods-enabled/realm
} # modules
radiusd: #### Loading Virtual Servers ####
server { # from file /etc/freeradius/3.0/radiusd.conf
} # server
server inner-tunnel { # from file /etc/freeradius/3.0/sites-enabled/inner-tunnel
# Loading authenticate {...}
# Loading authorize {...}
Ignoring "ldap" (see raddb/mods-available/README.rst)
# Loading session {...}
# Loading post-proxy {...}
# Loading post-auth {...}
} # server inner-tunnel
server default { # from file /etc/freeradius/3.0/sites-enabled/default
# Loading authenticate {...}
# Loading authorize {...}
# Loading preacct {...}
# Loading accounting {...}
# Loading session {...}
# Loading post-proxy {...}
# Loading post-auth {...}
} # server default
radiusd: #### Opening IP addresses and Ports ####
listen {
type = "auth"
ipaddr = 127.0.0.1
port = 18120
}
listen {
type = "auth"
ipaddr = *
port = 0
limit {
max_connections = 16
lifetime = 0
idle_timeout = 30
}
}
listen {
type = "acct"
ipaddr = *
port = 0
limit {
max_connections = 16
lifetime = 0
idle_timeout = 30
}
}
listen {
type = "auth"
ipv6addr = ::
port = 0
limit {
max_connections = 16
lifetime = 0
idle_timeout = 30
}
}
listen {
type = "acct"
ipv6addr = ::
port = 0
limit {
max_connections = 16
lifetime = 0
idle_timeout = 30
}
}
Listening on auth address 127.0.0.1 port 18120 bound to server inner-tunnel
Listening on auth address * port 1812 bound to server default
Listening on acct address * port 1813 bound to server default
Listening on auth address :: port 1812 bound to server default
Listening on acct address :: port 1813 bound to server default
Listening on proxy address * port 55085
Listening on proxy address :: port 40440
Ready to process requests
(0) Received Access-Request Id 0 from 127.0.0.1:49272 to 127.0.0.1:1812 length 162
(0) User-Name = "anonymous at somedomain.tld"
(0) NAS-IP-Address = 127.0.0.1
(0) Calling-Station-Id = "02-00-00-00-00-01"
(0) Framed-MTU = 1400
(0) NAS-Port-Type = Wireless-802.11
(0) Service-Type = Framed-User
(0) Connect-Info = "CONNECT 11Mbps 802.11b"
(0) EAP-Message = 0x0252001d01616e6f6e796d6f757340736f6d65646f6d61696e2e746c64
(0) Message-Authenticator = 0xa0061c41fefbafb03796bf4cb77473c8
(0) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default
(0) authorize {
(0) policy filter_username {
(0) if (&User-Name) {
(0) if (&User-Name) -> TRUE
(0) if (&User-Name) {
(0) if (&User-Name =~ / /) {
(0) if (&User-Name =~ / /) -> FALSE
(0) if (&User-Name =~ /@[^@]*@/ ) {
(0) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(0) if (&User-Name =~ /\.\./ ) {
(0) if (&User-Name =~ /\.\./ ) -> FALSE
(0) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(0) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE
(0) if (&User-Name =~ /\.$/) {
(0) if (&User-Name =~ /\.$/) -> FALSE
(0) if (&User-Name =~ /@\./) {
(0) if (&User-Name =~ /@\./) -> FALSE
(0) } # if (&User-Name) = notfound
(0) } # policy filter_username = notfound
(0) [preprocess] = ok
(0) [mschap] = noop
(0) [digest] = noop
(0) suffix: Checking for suffix after "@"
(0) suffix: Looking up realm "somedomain.tld" for User-Name = "anonymous at somedomain.tld"
(0) suffix: Found realm "somedomain.tld"
(0) suffix: Adding Stripped-User-Name = "anonymous"
(0) suffix: Adding Realm = "somedomain.tld"
(0) suffix: Authentication realm is LOCAL
(0) [suffix] = ok
(0) eap: Peer sent EAP Response (code 2) ID 82 length 29
(0) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize
(0) [eap] = ok
(0) } # authorize = ok
(0) Found Auth-Type = eap
(0) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(0) authenticate {
(0) eap: Peer sent packet with method EAP Identity (1)
(0) eap: Calling submodule eap_md5 to process data
(0) eap_md5: Issuing MD5 Challenge
(0) eap: Sending EAP Request (code 1) ID 83 length 22
(0) eap: EAP session adding &reply:State = 0xc1bbf9b5c1e8fddc
(0) [eap] = handled
(0) } # authenticate = handled
(0) Using Post-Auth-Type Challenge
(0) Post-Auth-Type sub-section not found. Ignoring.
(0) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(0) Sent Access-Challenge Id 0 from 127.0.0.1:1812 to 127.0.0.1:49272 length 0
(0) EAP-Message = 0x015300160410797adf9c4e1408f29a848892714c76a5
(0) Message-Authenticator = 0x00000000000000000000000000000000
(0) State = 0xc1bbf9b5c1e8fddc9b5489cd06a27075
(0) Finished request
Waking up in 4.9 seconds.
(1) Received Access-Request Id 1 from 127.0.0.1:49272 to 127.0.0.1:1812 length 157
(1) User-Name = "anonymous at somedomain.tld"
(1) NAS-IP-Address = 127.0.0.1
(1) Calling-Station-Id = "02-00-00-00-00-01"
(1) Framed-MTU = 1400
(1) NAS-Port-Type = Wireless-802.11
(1) Service-Type = Framed-User
(1) Connect-Info = "CONNECT 11Mbps 802.11b"
(1) EAP-Message = 0x025300060319
(1) State = 0xc1bbf9b5c1e8fddc9b5489cd06a27075
(1) Message-Authenticator = 0x479f03f3027fa8af27ec734b77f2e8eb
(1) session-state: No cached attributes
(1) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default
(1) authorize {
(1) policy filter_username {
(1) if (&User-Name) {
(1) if (&User-Name) -> TRUE
(1) if (&User-Name) {
(1) if (&User-Name =~ / /) {
(1) if (&User-Name =~ / /) -> FALSE
(1) if (&User-Name =~ /@[^@]*@/ ) {
(1) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(1) if (&User-Name =~ /\.\./ ) {
(1) if (&User-Name =~ /\.\./ ) -> FALSE
(1) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(1) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE
(1) if (&User-Name =~ /\.$/) {
(1) if (&User-Name =~ /\.$/) -> FALSE
(1) if (&User-Name =~ /@\./) {
(1) if (&User-Name =~ /@\./) -> FALSE
(1) } # if (&User-Name) = notfound
(1) } # policy filter_username = notfound
(1) [preprocess] = ok
(1) [mschap] = noop
(1) [digest] = noop
(1) suffix: Checking for suffix after "@"
(1) suffix: Looking up realm "somedomain.tld" for User-Name = "anonymous at somedomain.tld"
(1) suffix: Found realm "somedomain.tld"
(1) suffix: Adding Stripped-User-Name = "anonymous"
(1) suffix: Adding Realm = "somedomain.tld"
(1) suffix: Authentication realm is LOCAL
(1) [suffix] = ok
(1) eap: Peer sent EAP Response (code 2) ID 83 length 6
(1) eap: No EAP Start, assuming it's an on-going EAP conversation
(1) [eap] = updated
(1) sql: EXPAND %{User-Name}
(1) sql: --> anonymous at somedomain.tld
(1) sql: SQL-User-Name set to 'anonymous at somedomain.tld'
rlm_sql (sql): Reserved connection (1)
(1) sql: EXPAND SELECT id, username, attribute, value, op FROM radcheck WHERE username = '%{SQL-User-Name}' ORDER BY id
(1) sql: --> SELECT id, username, attribute, value, op FROM radcheck WHERE username = 'anonymous at somedomain.tld' ORDER BY id
(1) sql: Executing select query: SELECT id, username, attribute, value, op FROM radcheck WHERE username = 'anonymous at somedomain.tld' ORDER BY id
(1) sql: EXPAND SELECT groupname FROM radusergroup WHERE username = '%{SQL-User-Name}' ORDER BY priority
(1) sql: --> SELECT groupname FROM radusergroup WHERE username = 'anonymous at somedomain.tld' ORDER BY priority
(1) sql: Executing select query: SELECT groupname FROM radusergroup WHERE username = 'anonymous at somedomain.tld' ORDER BY priority
(1) sql: User not found in any groups
rlm_sql (sql): Released connection (1)
Need 4 more connections to reach 10 spares
rlm_sql (sql): Opening additional connection (6), 1 of 26 pending slots used
rlm_sql_mysql: Starting connect to MySQL server
rlm_sql_mysql: Connected to database 'radius' on Localhost via UNIX socket, server version 10.3.15-MariaDB-1, protocol version 10
(1) [sql] = notfound
(1) [expiration] = noop
(1) [logintime] = noop
(1) pap: WARNING: No "known good" password found for the user. Not setting Auth-Type
(1) pap: WARNING: Authentication will fail unless a "known good" password is available
(1) [pap] = noop
(1) } # authorize = updated
(1) Found Auth-Type = eap
(1) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(1) authenticate {
(1) eap: Expiring EAP session with state 0xc1bbf9b5c1e8fddc
(1) eap: Finished EAP session with state 0xc1bbf9b5c1e8fddc
(1) eap: Previous EAP request found for state 0xc1bbf9b5c1e8fddc, released from the list
(1) eap: Peer sent packet with method EAP NAK (3)
(1) eap: Found mutually acceptable type PEAP (25)
(1) eap: Calling submodule eap_peap to process data
(1) eap_peap: Initiating new EAP-TLS session
(1) eap_peap: [eaptls start] = request
(1) eap: Sending EAP Request (code 1) ID 84 length 6
(1) eap: EAP session adding &reply:State = 0xc1bbf9b5c0efe0dc
(1) [eap] = handled
(1) } # authenticate = handled
(1) Using Post-Auth-Type Challenge
(1) Post-Auth-Type sub-section not found. Ignoring.
(1) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(1) Sent Access-Challenge Id 1 from 127.0.0.1:1812 to 127.0.0.1:49272 length 0
(1) EAP-Message = 0x015400061920
(1) Message-Authenticator = 0x00000000000000000000000000000000
(1) State = 0xc1bbf9b5c0efe0dc9b5489cd06a27075
(1) Finished request
Waking up in 4.9 seconds.
(2) Received Access-Request Id 2 from 127.0.0.1:49272 to 127.0.0.1:1812 length 345
(2) User-Name = "anonymous at somedomain.tld"
(2) NAS-IP-Address = 127.0.0.1
(2) Calling-Station-Id = "02-00-00-00-00-01"
(2) Framed-MTU = 1400
(2) NAS-Port-Type = Wireless-802.11
(2) Service-Type = Framed-User
(2) Connect-Info = "CONNECT 11Mbps 802.11b"
(2) EAP-Message = 0x025400c21980000000b816030100b3010000af0303ae12f8ff71b47370814e322a1427a487b79c2bd9c49b47ee44925c8cac6777b7000038c02cc030009fcca9cca8ccaac02bc02f009ec024c028006bc023c0270067c00ac0140039c009c0130033009d009c003d003c0035002f00ff0100004e000b00
(2) State = 0xc1bbf9b5c0efe0dc9b5489cd06a27075
(2) Message-Authenticator = 0x3f0b0ed3942e7aa4523688bbd1ea0d89
(2) session-state: No cached attributes
(2) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default
(2) authorize {
(2) policy filter_username {
(2) if (&User-Name) {
(2) if (&User-Name) -> TRUE
(2) if (&User-Name) {
(2) if (&User-Name =~ / /) {
(2) if (&User-Name =~ / /) -> FALSE
(2) if (&User-Name =~ /@[^@]*@/ ) {
(2) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(2) if (&User-Name =~ /\.\./ ) {
(2) if (&User-Name =~ /\.\./ ) -> FALSE
(2) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(2) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE
(2) if (&User-Name =~ /\.$/) {
(2) if (&User-Name =~ /\.$/) -> FALSE
(2) if (&User-Name =~ /@\./) {
(2) if (&User-Name =~ /@\./) -> FALSE
(2) } # if (&User-Name) = notfound
(2) } # policy filter_username = notfound
(2) [preprocess] = ok
(2) [mschap] = noop
(2) [digest] = noop
(2) suffix: Checking for suffix after "@"
(2) suffix: Looking up realm "somedomain.tld" for User-Name = "anonymous at somedomain.tld"
(2) suffix: Found realm "somedomain.tld"
(2) suffix: Adding Stripped-User-Name = "anonymous"
(2) suffix: Adding Realm = "somedomain.tld"
(2) suffix: Authentication realm is LOCAL
(2) [suffix] = ok
(2) eap: Peer sent EAP Response (code 2) ID 84 length 194
(2) eap: Continuing tunnel setup
(2) [eap] = ok
(2) } # authorize = ok
(2) Found Auth-Type = eap
(2) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(2) authenticate {
(2) eap: Expiring EAP session with state 0xc1bbf9b5c0efe0dc
(2) eap: Finished EAP session with state 0xc1bbf9b5c0efe0dc
(2) eap: Previous EAP request found for state 0xc1bbf9b5c0efe0dc, released from the list
(2) eap: Peer sent packet with method EAP PEAP (25)
(2) eap: Calling submodule eap_peap to process data
(2) eap_peap: Continuing EAP-TLS
(2) eap_peap: Peer indicated complete TLS record size will be 184 bytes
(2) eap_peap: Got complete TLS record (184 bytes)
(2) eap_peap: [eaptls verify] = length included
(2) eap_peap: (other): before SSL initialization
(2) eap_peap: TLS_accept: before SSL initialization
(2) eap_peap: TLS_accept: before SSL initialization
(2) eap_peap: <<< recv UNKNOWN TLS VERSION ?0304? [length 00b3]
(2) eap_peap: TLS_accept: SSLv3/TLS read client hello
(2) eap_peap: >>> send TLS 1.2 [length 003d]
(2) eap_peap: TLS_accept: SSLv3/TLS write server hello
(2) eap_peap: >>> send TLS 1.2 [length 02e7]
(2) eap_peap: TLS_accept: SSLv3/TLS write certificate
(2) eap_peap: >>> send TLS 1.2 [length 014d]
(2) eap_peap: TLS_accept: SSLv3/TLS write key exchange
(2) eap_peap: >>> send TLS 1.2 [length 0004]
(2) eap_peap: TLS_accept: SSLv3/TLS write server done
(2) eap_peap: TLS_accept: Need to read more data: SSLv3/TLS write server done
(2) eap_peap: In SSL Handshake Phase
(2) eap_peap: In SSL Accept mode
(2) eap_peap: [eaptls process] = handled
(2) eap: Sending EAP Request (code 1) ID 85 length 1004
(2) eap: EAP session adding &reply:State = 0xc1bbf9b5c3eee0dc
(2) [eap] = handled
(2) } # authenticate = handled
(2) Using Post-Auth-Type Challenge
(2) Post-Auth-Type sub-section not found. Ignoring.
(2) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(2) Sent Access-Challenge Id 2 from 127.0.0.1:1812 to 127.0.0.1:49272 length 0
(2) EAP-Message = 0x015503ec19c000000489160303003d0200003903036725ad0ba4b6232fc2cf6806fbe3dbac7cfe8055fe88ccd5444f574e4752440100c030000011ff01000100000b0004030001020017000016030302e70b0002e30002e00002dd308202d9308201c1a00302010202140fb29d65591483ef539b3f4010
(2) Message-Authenticator = 0x00000000000000000000000000000000
(2) State = 0xc1bbf9b5c3eee0dc9b5489cd06a27075
(2) Finished request
Waking up in 4.9 seconds.
(3) Received Access-Request Id 3 from 127.0.0.1:49272 to 127.0.0.1:1812 length 157
(3) User-Name = "anonymous at somedomain.tld"
(3) NAS-IP-Address = 127.0.0.1
(3) Calling-Station-Id = "02-00-00-00-00-01"
(3) Framed-MTU = 1400
(3) NAS-Port-Type = Wireless-802.11
(3) Service-Type = Framed-User
(3) Connect-Info = "CONNECT 11Mbps 802.11b"
(3) EAP-Message = 0x025500061900
(3) State = 0xc1bbf9b5c3eee0dc9b5489cd06a27075
(3) Message-Authenticator = 0x13005fa0d33fd0b42edb51b1c7259a6e
(3) session-state: No cached attributes
(3) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default
(3) authorize {
(3) policy filter_username {
(3) if (&User-Name) {
(3) if (&User-Name) -> TRUE
(3) if (&User-Name) {
(3) if (&User-Name =~ / /) {
(3) if (&User-Name =~ / /) -> FALSE
(3) if (&User-Name =~ /@[^@]*@/ ) {
(3) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(3) if (&User-Name =~ /\.\./ ) {
(3) if (&User-Name =~ /\.\./ ) -> FALSE
(3) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(3) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE
(3) if (&User-Name =~ /\.$/) {
(3) if (&User-Name =~ /\.$/) -> FALSE
(3) if (&User-Name =~ /@\./) {
(3) if (&User-Name =~ /@\./) -> FALSE
(3) } # if (&User-Name) = notfound
(3) } # policy filter_username = notfound
(3) [preprocess] = ok
(3) [mschap] = noop
(3) [digest] = noop
(3) suffix: Checking for suffix after "@"
(3) suffix: Looking up realm "somedomain.tld" for User-Name = "anonymous at somedomain.tld"
(3) suffix: Found realm "somedomain.tld"
(3) suffix: Adding Stripped-User-Name = "anonymous"
(3) suffix: Adding Realm = "somedomain.tld"
(3) suffix: Authentication realm is LOCAL
(3) [suffix] = ok
(3) eap: Peer sent EAP Response (code 2) ID 85 length 6
(3) eap: Continuing tunnel setup
(3) [eap] = ok
(3) } # authorize = ok
(3) Found Auth-Type = eap
(3) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(3) authenticate {
(3) eap: Expiring EAP session with state 0xc1bbf9b5c3eee0dc
(3) eap: Finished EAP session with state 0xc1bbf9b5c3eee0dc
(3) eap: Previous EAP request found for state 0xc1bbf9b5c3eee0dc, released from the list
(3) eap: Peer sent packet with method EAP PEAP (25)
(3) eap: Calling submodule eap_peap to process data
(3) eap_peap: Continuing EAP-TLS
(3) eap_peap: Peer ACKed our handshake fragment
(3) eap_peap: [eaptls verify] = request
(3) eap_peap: [eaptls process] = handled
(3) eap: Sending EAP Request (code 1) ID 86 length 173
(3) eap: EAP session adding &reply:State = 0xc1bbf9b5c2ede0dc
(3) [eap] = handled
(3) } # authenticate = handled
(3) Using Post-Auth-Type Challenge
(3) Post-Auth-Type sub-section not found. Ignoring.
(3) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(3) Sent Access-Challenge Id 3 from 127.0.0.1:1812 to 127.0.0.1:49272 length 0
(3) EAP-Message = 0x015600ad1900ab35a8a86033413fb3cddd019e174fccb5953d2541c192ffaef015bbce514e303b06d32d28bbab2bba94a9a1a03c47aae74921b1fd8c0de02e1c593752df491e6b924fbe37bb77c7177738416042d6874d509db9067089c1b856082bb210ffb4f6471be0f1f597721c5d4cec71af98b081
(3) Message-Authenticator = 0x00000000000000000000000000000000
(3) State = 0xc1bbf9b5c2ede0dc9b5489cd06a27075
(3) Finished request
Waking up in 4.9 seconds.
(4) Received Access-Request Id 4 from 127.0.0.1:49272 to 127.0.0.1:1812 length 287
(4) User-Name = "anonymous at somedomain.tld"
(4) NAS-IP-Address = 127.0.0.1
(4) Calling-Station-Id = "02-00-00-00-00-01"
(4) Framed-MTU = 1400
(4) NAS-Port-Type = Wireless-802.11
(4) Service-Type = Framed-User
(4) Connect-Info = "CONNECT 11Mbps 802.11b"
(4) EAP-Message = 0x0256008819800000007e1603030046100000424104ee224da73be2947e0561fba4e750b34b507c5ac89ec2acea081d4d6f47ca46cfbace3eeed643337e247994d14be4f69944539d5ea5556bbda52edf35d667e49814030300010116030300288dc5e34ca5e1708ea2ca961beb98eda33b0ac8ab10f4ab
(4) State = 0xc1bbf9b5c2ede0dc9b5489cd06a27075
(4) Message-Authenticator = 0xc022f298ddec0b214c503f5b6524e715
(4) session-state: No cached attributes
(4) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default
(4) authorize {
(4) policy filter_username {
(4) if (&User-Name) {
(4) if (&User-Name) -> TRUE
(4) if (&User-Name) {
(4) if (&User-Name =~ / /) {
(4) if (&User-Name =~ / /) -> FALSE
(4) if (&User-Name =~ /@[^@]*@/ ) {
(4) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(4) if (&User-Name =~ /\.\./ ) {
(4) if (&User-Name =~ /\.\./ ) -> FALSE
(4) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(4) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE
(4) if (&User-Name =~ /\.$/) {
(4) if (&User-Name =~ /\.$/) -> FALSE
(4) if (&User-Name =~ /@\./) {
(4) if (&User-Name =~ /@\./) -> FALSE
(4) } # if (&User-Name) = notfound
(4) } # policy filter_username = notfound
(4) [preprocess] = ok
(4) [mschap] = noop
(4) [digest] = noop
(4) suffix: Checking for suffix after "@"
(4) suffix: Looking up realm "somedomain.tld" for User-Name = "anonymous at somedomain.tld"
(4) suffix: Found realm "somedomain.tld"
(4) suffix: Adding Stripped-User-Name = "anonymous"
(4) suffix: Adding Realm = "somedomain.tld"
(4) suffix: Authentication realm is LOCAL
(4) [suffix] = ok
(4) eap: Peer sent EAP Response (code 2) ID 86 length 136
(4) eap: Continuing tunnel setup
(4) [eap] = ok
(4) } # authorize = ok
(4) Found Auth-Type = eap
(4) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(4) authenticate {
(4) eap: Expiring EAP session with state 0xc1bbf9b5c2ede0dc
(4) eap: Finished EAP session with state 0xc1bbf9b5c2ede0dc
(4) eap: Previous EAP request found for state 0xc1bbf9b5c2ede0dc, released from the list
(4) eap: Peer sent packet with method EAP PEAP (25)
(4) eap: Calling submodule eap_peap to process data
(4) eap_peap: Continuing EAP-TLS
(4) eap_peap: Peer indicated complete TLS record size will be 126 bytes
(4) eap_peap: Got complete TLS record (126 bytes)
(4) eap_peap: [eaptls verify] = length included
(4) eap_peap: TLS_accept: SSLv3/TLS write server done
(4) eap_peap: <<< recv TLS 1.2 [length 0046]
(4) eap_peap: TLS_accept: SSLv3/TLS read client key exchange
(4) eap_peap: TLS_accept: SSLv3/TLS read change cipher spec
(4) eap_peap: <<< recv TLS 1.2 [length 0010]
(4) eap_peap: TLS_accept: SSLv3/TLS read finished
(4) eap_peap: >>> send TLS 1.2 [length 0001]
(4) eap_peap: TLS_accept: SSLv3/TLS write change cipher spec
(4) eap_peap: >>> send TLS 1.2 [length 0010]
(4) eap_peap: TLS_accept: SSLv3/TLS write finished
(4) eap_peap: (other): SSL negotiation finished successfully
(4) eap_peap: SSL Connection Established
(4) eap_peap: [eaptls process] = handled
(4) eap: Sending EAP Request (code 1) ID 87 length 57
(4) eap: EAP session adding &reply:State = 0xc1bbf9b5c5ece0dc
(4) [eap] = handled
(4) } # authenticate = handled
(4) Using Post-Auth-Type Challenge
(4) Post-Auth-Type sub-section not found. Ignoring.
(4) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(4) Sent Access-Challenge Id 4 from 127.0.0.1:1812 to 127.0.0.1:49272 length 0
(4) EAP-Message = 0x0157003919001403030001011603030028d19eb84f73fec693c7961b6b3040d3e60eb4e21277f1fa6ef1e5f2386829cfa9500c8348ecc563cb
(4) Message-Authenticator = 0x00000000000000000000000000000000
(4) State = 0xc1bbf9b5c5ece0dc9b5489cd06a27075
(4) Finished request
Waking up in 4.9 seconds.
(5) Received Access-Request Id 5 from 127.0.0.1:49272 to 127.0.0.1:1812 length 157
(5) User-Name = "anonymous at somedomain.tld"
(5) NAS-IP-Address = 127.0.0.1
(5) Calling-Station-Id = "02-00-00-00-00-01"
(5) Framed-MTU = 1400
(5) NAS-Port-Type = Wireless-802.11
(5) Service-Type = Framed-User
(5) Connect-Info = "CONNECT 11Mbps 802.11b"
(5) EAP-Message = 0x025700061900
(5) State = 0xc1bbf9b5c5ece0dc9b5489cd06a27075
(5) Message-Authenticator = 0xeb0cc49c5e890568e1dd16171041f073
(5) session-state: No cached attributes
(5) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default
(5) authorize {
(5) policy filter_username {
(5) if (&User-Name) {
(5) if (&User-Name) -> TRUE
(5) if (&User-Name) {
(5) if (&User-Name =~ / /) {
(5) if (&User-Name =~ / /) -> FALSE
(5) if (&User-Name =~ /@[^@]*@/ ) {
(5) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(5) if (&User-Name =~ /\.\./ ) {
(5) if (&User-Name =~ /\.\./ ) -> FALSE
(5) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(5) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE
(5) if (&User-Name =~ /\.$/) {
(5) if (&User-Name =~ /\.$/) -> FALSE
(5) if (&User-Name =~ /@\./) {
(5) if (&User-Name =~ /@\./) -> FALSE
(5) } # if (&User-Name) = notfound
(5) } # policy filter_username = notfound
(5) [preprocess] = ok
(5) [mschap] = noop
(5) [digest] = noop
(5) suffix: Checking for suffix after "@"
(5) suffix: Looking up realm "somedomain.tld" for User-Name = "anonymous at somedomain.tld"
(5) suffix: Found realm "somedomain.tld"
(5) suffix: Adding Stripped-User-Name = "anonymous"
(5) suffix: Adding Realm = "somedomain.tld"
(5) suffix: Authentication realm is LOCAL
(5) [suffix] = ok
(5) eap: Peer sent EAP Response (code 2) ID 87 length 6
(5) eap: Continuing tunnel setup
(5) [eap] = ok
(5) } # authorize = ok
(5) Found Auth-Type = eap
(5) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(5) authenticate {
(5) eap: Expiring EAP session with state 0xc1bbf9b5c5ece0dc
(5) eap: Finished EAP session with state 0xc1bbf9b5c5ece0dc
(5) eap: Previous EAP request found for state 0xc1bbf9b5c5ece0dc, released from the list
(5) eap: Peer sent packet with method EAP PEAP (25)
(5) eap: Calling submodule eap_peap to process data
(5) eap_peap: Continuing EAP-TLS
(5) eap_peap: Peer ACKed our handshake fragment. handshake is finished
(5) eap_peap: [eaptls verify] = success
(5) eap_peap: [eaptls process] = success
(5) eap_peap: Session established. Decoding tunneled attributes
(5) eap_peap: PEAP state TUNNEL ESTABLISHED
(5) eap: Sending EAP Request (code 1) ID 88 length 40
(5) eap: EAP session adding &reply:State = 0xc1bbf9b5c4e3e0dc
(5) [eap] = handled
(5) } # authenticate = handled
(5) Using Post-Auth-Type Challenge
(5) Post-Auth-Type sub-section not found. Ignoring.
(5) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(5) Sent Access-Challenge Id 5 from 127.0.0.1:1812 to 127.0.0.1:49272 length 0
(5) EAP-Message = 0x015800281900170303001dd19eb84f73fec694030c4cecce294a8cf34b730175628b1b3005b788c6
(5) Message-Authenticator = 0x00000000000000000000000000000000
(5) State = 0xc1bbf9b5c4e3e0dc9b5489cd06a27075
(5) Finished request
Waking up in 4.9 seconds.
(6) Received Access-Request Id 6 from 127.0.0.1:49272 to 127.0.0.1:1812 length 206
(6) User-Name = "anonymous at somedomain.tld"
(6) NAS-IP-Address = 127.0.0.1
(6) Calling-Station-Id = "02-00-00-00-00-01"
(6) Framed-MTU = 1400
(6) NAS-Port-Type = Wireless-802.11
(6) Service-Type = Framed-User
(6) Connect-Info = "CONNECT 11Mbps 802.11b"
(6) EAP-Message = 0x025800371900170303002c8dc5e34ca5e1708f5344cb01d135e0f30323d9ea58ccc03717141704b0b466b8c49af0c581de2f3ad9c8b5c3
(6) State = 0xc1bbf9b5c4e3e0dc9b5489cd06a27075
(6) Message-Authenticator = 0xdd534a1669e206a9eac8efbd4d74e798
(6) session-state: No cached attributes
(6) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default
(6) authorize {
(6) policy filter_username {
(6) if (&User-Name) {
(6) if (&User-Name) -> TRUE
(6) if (&User-Name) {
(6) if (&User-Name =~ / /) {
(6) if (&User-Name =~ / /) -> FALSE
(6) if (&User-Name =~ /@[^@]*@/ ) {
(6) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(6) if (&User-Name =~ /\.\./ ) {
(6) if (&User-Name =~ /\.\./ ) -> FALSE
(6) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(6) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE
(6) if (&User-Name =~ /\.$/) {
(6) if (&User-Name =~ /\.$/) -> FALSE
(6) if (&User-Name =~ /@\./) {
(6) if (&User-Name =~ /@\./) -> FALSE
(6) } # if (&User-Name) = notfound
(6) } # policy filter_username = notfound
(6) [preprocess] = ok
(6) [mschap] = noop
(6) [digest] = noop
(6) suffix: Checking for suffix after "@"
(6) suffix: Looking up realm "somedomain.tld" for User-Name = "anonymous at somedomain.tld"
(6) suffix: Found realm "somedomain.tld"
(6) suffix: Adding Stripped-User-Name = "anonymous"
(6) suffix: Adding Realm = "somedomain.tld"
(6) suffix: Authentication realm is LOCAL
(6) [suffix] = ok
(6) eap: Peer sent EAP Response (code 2) ID 88 length 55
(6) eap: Continuing tunnel setup
(6) [eap] = ok
(6) } # authorize = ok
(6) Found Auth-Type = eap
(6) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(6) authenticate {
(6) eap: Expiring EAP session with state 0xc1bbf9b5c4e3e0dc
(6) eap: Finished EAP session with state 0xc1bbf9b5c4e3e0dc
(6) eap: Previous EAP request found for state 0xc1bbf9b5c4e3e0dc, released from the list
(6) eap: Peer sent packet with method EAP PEAP (25)
(6) eap: Calling submodule eap_peap to process data
(6) eap_peap: Continuing EAP-TLS
(6) eap_peap: [eaptls verify] = ok
(6) eap_peap: Done initial handshake
(6) eap_peap: [eaptls process] = ok
(6) eap_peap: Session established. Decoding tunneled attributes
(6) eap_peap: PEAP state WAITING FOR INNER IDENTITY
(6) eap_peap: Identity - test at somedomain.tld
(6) eap_peap: Got inner identity 'test at somedomain.tld'
(6) eap_peap: Setting default EAP type for tunneled EAP session
(6) eap_peap: Got tunneled request
(6) eap_peap: EAP-Message = 0x02580018017465737440736f6d65646f6d61696e2e746c64
(6) eap_peap: Setting User-Name to test at somedomain.tld
(6) eap_peap: Sending tunneled request to inner-tunnel
(6) eap_peap: EAP-Message = 0x02580018017465737440736f6d65646f6d61696e2e746c64
(6) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1
(6) eap_peap: User-Name = "test at somedomain.tld"
(6) Virtual server inner-tunnel received request
(6) EAP-Message = 0x02580018017465737440736f6d65646f6d61696e2e746c64
(6) FreeRADIUS-Proxied-To = 127.0.0.1
(6) User-Name = "test at somedomain.tld"
(6) server inner-tunnel {
(6) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/inner-tunnel
(6) authorize {
(6) policy filter_username {
(6) if (&User-Name) {
(6) if (&User-Name) -> TRUE
(6) if (&User-Name) {
(6) if (&User-Name =~ / /) {
(6) if (&User-Name =~ / /) -> FALSE
(6) if (&User-Name =~ /@[^@]*@/ ) {
(6) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(6) if (&User-Name =~ /\.\./ ) {
(6) if (&User-Name =~ /\.\./ ) -> FALSE
(6) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(6) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE
(6) if (&User-Name =~ /\.$/) {
(6) if (&User-Name =~ /\.$/) -> FALSE
(6) if (&User-Name =~ /@\./) {
(6) if (&User-Name =~ /@\./) -> FALSE
(6) } # if (&User-Name) = notfound
(6) } # policy filter_username = notfound
(6) [mschap] = noop
(6) suffix: Checking for suffix after "@"
(6) suffix: Looking up realm "somedomain.tld" for User-Name = "test at somedomain.tld"
(6) suffix: Found realm "somedomain.tld"
(6) suffix: Adding Stripped-User-Name = "test"
(6) suffix: Adding Realm = "somedomain.tld"
(6) suffix: Authentication realm is LOCAL
(6) [suffix] = ok
(6) update control {
(6) &Proxy-To-Realm := LOCAL
(6) } # update control = noop
(6) eap: Peer sent EAP Response (code 2) ID 88 length 24
(6) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize
(6) [eap] = ok
(6) } # authorize = ok
(6) Found Auth-Type = eap
(6) # Executing group from file /etc/freeradius/3.0/sites-enabled/inner-tunnel
(6) authenticate {
(6) eap: Peer sent packet with method EAP Identity (1)
(6) eap: Calling submodule eap_mschapv2 to process data
(6) eap_mschapv2: Issuing Challenge
(6) eap: Sending EAP Request (code 1) ID 89 length 43
(6) eap: EAP session adding &reply:State = 0xfd6a17b0fd330df6
(6) [eap] = handled
(6) } # authenticate = handled
(6) } # server inner-tunnel
(6) Virtual server sending reply
(6) EAP-Message = 0x0159002b1a0159002610cc8dbf56ae6aae58fe1e5105e185defc667265657261646975732d332e302e3137
(6) Message-Authenticator = 0x00000000000000000000000000000000
(6) State = 0xfd6a17b0fd330df63e04b83f1606d4fa
(6) eap_peap: Got tunneled reply code 11
(6) eap_peap: EAP-Message = 0x0159002b1a0159002610cc8dbf56ae6aae58fe1e5105e185defc667265657261646975732d332e302e3137
(6) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000
(6) eap_peap: State = 0xfd6a17b0fd330df63e04b83f1606d4fa
(6) eap_peap: Got tunneled reply RADIUS code 11
(6) eap_peap: EAP-Message = 0x0159002b1a0159002610cc8dbf56ae6aae58fe1e5105e185defc667265657261646975732d332e302e3137
(6) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000
(6) eap_peap: State = 0xfd6a17b0fd330df63e04b83f1606d4fa
(6) eap_peap: Got tunneled Access-Challenge
(6) eap: Sending EAP Request (code 1) ID 89 length 74
(6) eap: EAP session adding &reply:State = 0xc1bbf9b5c7e2e0dc
(6) [eap] = handled
(6) } # authenticate = handled
(6) Using Post-Auth-Type Challenge
(6) Post-Auth-Type sub-section not found. Ignoring.
(6) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(6) Sent Access-Challenge Id 6 from 127.0.0.1:1812 to 127.0.0.1:49272 length 0
(6) EAP-Message = 0x0159004a1900170303003fd19eb84f73fec695bcec036883736a1e5e835c751853246d4e890fd99be5d7579d3f12e3b8de5644d068b0e28c06151d86c5b1a618cbfd58b32988752d6d5f
(6) Message-Authenticator = 0x00000000000000000000000000000000
(6) State = 0xc1bbf9b5c7e2e0dc9b5489cd06a27075
(6) Finished request
Waking up in 4.9 seconds.
(7) Received Access-Request Id 7 from 127.0.0.1:49272 to 127.0.0.1:1812 length 260
(7) User-Name = "anonymous at somedomain.tld"
(7) NAS-IP-Address = 127.0.0.1
(7) Calling-Station-Id = "02-00-00-00-00-01"
(7) Framed-MTU = 1400
(7) NAS-Port-Type = Wireless-802.11
(7) Service-Type = Framed-User
(7) Connect-Info = "CONNECT 11Mbps 802.11b"
(7) EAP-Message = 0x0259006d190017030300628dc5e34ca5e170906e9ff2b9b1d6c4e37cfb375e62708a19ef5f590fdb5451b3d5c88fb551dd6c8f0d5030f93baf2ce810154140076fe11b3b7f37ae3cc7a14ec1fcfc164947229643d15e0315516f7835e2096da687f0a8c51dbede42ea7a94c105
(7) State = 0xc1bbf9b5c7e2e0dc9b5489cd06a27075
(7) Message-Authenticator = 0x876412184d8d576c3e1d815b83821657
(7) session-state: No cached attributes
(7) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default
(7) authorize {
(7) policy filter_username {
(7) if (&User-Name) {
(7) if (&User-Name) -> TRUE
(7) if (&User-Name) {
(7) if (&User-Name =~ / /) {
(7) if (&User-Name =~ / /) -> FALSE
(7) if (&User-Name =~ /@[^@]*@/ ) {
(7) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(7) if (&User-Name =~ /\.\./ ) {
(7) if (&User-Name =~ /\.\./ ) -> FALSE
(7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE
(7) if (&User-Name =~ /\.$/) {
(7) if (&User-Name =~ /\.$/) -> FALSE
(7) if (&User-Name =~ /@\./) {
(7) if (&User-Name =~ /@\./) -> FALSE
(7) } # if (&User-Name) = notfound
(7) } # policy filter_username = notfound
(7) [preprocess] = ok
(7) [mschap] = noop
(7) [digest] = noop
(7) suffix: Checking for suffix after "@"
(7) suffix: Looking up realm "somedomain.tld" for User-Name = "anonymous at somedomain.tld"
(7) suffix: Found realm "somedomain.tld"
(7) suffix: Adding Stripped-User-Name = "anonymous"
(7) suffix: Adding Realm = "somedomain.tld"
(7) suffix: Authentication realm is LOCAL
(7) [suffix] = ok
(7) eap: Peer sent EAP Response (code 2) ID 89 length 109
(7) eap: Continuing tunnel setup
(7) [eap] = ok
(7) } # authorize = ok
(7) Found Auth-Type = eap
(7) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(7) authenticate {
(7) eap: Expiring EAP session with state 0xfd6a17b0fd330df6
(7) eap: Finished EAP session with state 0xc1bbf9b5c7e2e0dc
(7) eap: Previous EAP request found for state 0xc1bbf9b5c7e2e0dc, released from the list
(7) eap: Peer sent packet with method EAP PEAP (25)
(7) eap: Calling submodule eap_peap to process data
(7) eap_peap: Continuing EAP-TLS
(7) eap_peap: [eaptls verify] = ok
(7) eap_peap: Done initial handshake
(7) eap_peap: [eaptls process] = ok
(7) eap_peap: Session established. Decoding tunneled attributes
(7) eap_peap: PEAP state phase2
(7) eap_peap: EAP method MSCHAPv2 (26)
(7) eap_peap: Got tunneled request
(7) eap_peap: EAP-Message = 0x0259004e1a0259004931e1c41892109aeca427a219b9dc0f1182000000000000000067e6bc0863ff2766b6a23d19cd142586c35eed003c7dfc8e007465737440736f6d65646f6d61696e2e746c64
(7) eap_peap: Setting User-Name to test at somedomain.tld
(7) eap_peap: Sending tunneled request to inner-tunnel
(7) eap_peap: EAP-Message = 0x0259004e1a0259004931e1c41892109aeca427a219b9dc0f1182000000000000000067e6bc0863ff2766b6a23d19cd142586c35eed003c7dfc8e007465737440736f6d65646f6d61696e2e746c64
(7) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1
(7) eap_peap: User-Name = "test at somedomain.tld"
(7) eap_peap: State = 0xfd6a17b0fd330df63e04b83f1606d4fa
(7) Virtual server inner-tunnel received request
(7) EAP-Message = 0x0259004e1a0259004931e1c41892109aeca427a219b9dc0f1182000000000000000067e6bc0863ff2766b6a23d19cd142586c35eed003c7dfc8e007465737440736f6d65646f6d61696e2e746c64
(7) FreeRADIUS-Proxied-To = 127.0.0.1
(7) User-Name = "test at somedomain.tld"
(7) State = 0xfd6a17b0fd330df63e04b83f1606d4fa
(7) server inner-tunnel {
(7) session-state: No cached attributes
(7) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/inner-tunnel
(7) authorize {
(7) policy filter_username {
(7) if (&User-Name) {
(7) if (&User-Name) -> TRUE
(7) if (&User-Name) {
(7) if (&User-Name =~ / /) {
(7) if (&User-Name =~ / /) -> FALSE
(7) if (&User-Name =~ /@[^@]*@/ ) {
(7) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(7) if (&User-Name =~ /\.\./ ) {
(7) if (&User-Name =~ /\.\./ ) -> FALSE
(7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE
(7) if (&User-Name =~ /\.$/) {
(7) if (&User-Name =~ /\.$/) -> FALSE
(7) if (&User-Name =~ /@\./) {
(7) if (&User-Name =~ /@\./) -> FALSE
(7) } # if (&User-Name) = notfound
(7) } # policy filter_username = notfound
(7) [mschap] = noop
(7) suffix: Checking for suffix after "@"
(7) suffix: Looking up realm "somedomain.tld" for User-Name = "test at somedomain.tld"
(7) suffix: Found realm "somedomain.tld"
(7) suffix: Adding Stripped-User-Name = "test"
(7) suffix: Adding Realm = "somedomain.tld"
(7) suffix: Authentication realm is LOCAL
(7) [suffix] = ok
(7) update control {
(7) &Proxy-To-Realm := LOCAL
(7) } # update control = noop
(7) eap: Peer sent EAP Response (code 2) ID 89 length 78
(7) eap: No EAP Start, assuming it's an on-going EAP conversation
(7) [eap] = updated
(7) [files] = noop
(7) sql: EXPAND %{User-Name}
(7) sql: --> test at somedomain.tld
(7) sql: SQL-User-Name set to 'test at somedomain.tld'
rlm_sql (sql): Reserved connection (2)
(7) sql: EXPAND SELECT id, username, attribute, value, op FROM radcheck WHERE username = '%{SQL-User-Name}' ORDER BY id
(7) sql: --> SELECT id, username, attribute, value, op FROM radcheck WHERE username = 'test at somedomain.tld' ORDER BY id
(7) sql: Executing select query: SELECT id, username, attribute, value, op FROM radcheck WHERE username = 'test at somedomain.tld' ORDER BY id
(7) sql: EXPAND SELECT groupname FROM radusergroup WHERE username = '%{SQL-User-Name}' ORDER BY priority
(7) sql: --> SELECT groupname FROM radusergroup WHERE username = 'test at somedomain.tld' ORDER BY priority
(7) sql: Executing select query: SELECT groupname FROM radusergroup WHERE username = 'test at somedomain.tld' ORDER BY priority
(7) sql: User not found in any groups
rlm_sql (sql): Released connection (2)
(7) [sql] = notfound
(7) [expiration] = noop
(7) [logintime] = noop
(7) [pap] = noop
(7) } # authorize = updated
(7) Found Auth-Type = eap
(7) # Executing group from file /etc/freeradius/3.0/sites-enabled/inner-tunnel
(7) authenticate {
(7) eap: Expiring EAP session with state 0xfd6a17b0fd330df6
(7) eap: Finished EAP session with state 0xfd6a17b0fd330df6
(7) eap: Previous EAP request found for state 0xfd6a17b0fd330df6, released from the list
(7) eap: Peer sent packet with method EAP MSCHAPv2 (26)
(7) eap: Calling submodule eap_mschapv2 to process data
(7) eap_mschapv2: # Executing group from file /etc/freeradius/3.0/sites-enabled/inner-tunnel
(7) eap_mschapv2: authenticate {
(7) mschap: WARNING: No Cleartext-Password configured. Cannot create NT-Password
(7) mschap: WARNING: No Cleartext-Password configured. Cannot create LM-Password
(7) mschap: Creating challenge hash with username: test at somedomain.tld
(7) mschap: Client is using MS-CHAPv2
(7) mschap: ERROR: FAILED: No NT/LM-Password. Cannot perform authentication
(7) mschap: ERROR: MS-CHAP2-Response is incorrect
(7) [mschap] = reject
(7) } # authenticate = reject
(7) eap: Sending EAP Failure (code 4) ID 89 length 4
(7) eap: Freeing handler
(7) [eap] = reject
(7) } # authenticate = reject
(7) Failed to authenticate the user
(7) Using Post-Auth-Type Reject
(7) # Executing group from file /etc/freeradius/3.0/sites-enabled/inner-tunnel
(7) Post-Auth-Type REJECT {
(7) sql: EXPAND .query
(7) sql: --> .query
(7) sql: Using query template 'query'
rlm_sql (sql): Reserved connection (3)
(7) sql: EXPAND %{User-Name}
(7) sql: --> test at somedomain.tld
(7) sql: SQL-User-Name set to 'test at somedomain.tld'
(7) sql: EXPAND INSERT INTO radpostauth (username, pass, reply, authdate) VALUES ( '%{SQL-User-Name}', '%{%{User-Password}:-%{Chap-Password}}', '%{reply:Packet-Type}', '%S')
(7) sql: --> INSERT INTO radpostauth (username, pass, reply, authdate) VALUES ( 'test at somedomain.tld', '', 'Access-Reject', '2019-09-01 14:26:15')
(7) sql: Executing query: INSERT INTO radpostauth (username, pass, reply, authdate) VALUES ( 'test at somedomain.tld', '', 'Access-Reject', '2019-09-01 14:26:15')
(7) sql: SQL query returned: success
(7) sql: 1 record(s) updated
rlm_sql (sql): Released connection (3)
(7) [sql] = ok
(7) attr_filter.access_reject: EXPAND %{User-Name}
(7) attr_filter.access_reject: --> test at somedomain.tld
(7) attr_filter.access_reject: Matched entry DEFAULT at line 11
(7) [attr_filter.access_reject] = updated
(7) update outer.session-state {
(7) &Module-Failure-Message := &request:Module-Failure-Message -> 'mschap: FAILED: No NT/LM-Password. Cannot perform authentication'
(7) } # update outer.session-state = noop
(7) } # Post-Auth-Type REJECT = updated
(7) } # server inner-tunnel
(7) Virtual server sending reply
(7) MS-CHAP-Error = "YE=691 R=1 C=dc0350ae832b45ea5440fa0bb2c495cd V=3 M=Authentication rejected"
(7) EAP-Message = 0x04590004
(7) Message-Authenticator = 0x00000000000000000000000000000000
(7) eap_peap: Got tunneled reply code 3
(7) eap_peap: MS-CHAP-Error = "YE=691 R=1 C=dc0350ae832b45ea5440fa0bb2c495cd V=3 M=Authentication rejected"
(7) eap_peap: EAP-Message = 0x04590004
(7) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000
(7) eap_peap: Got tunneled reply RADIUS code 3
(7) eap_peap: MS-CHAP-Error = "YE=691 R=1 C=dc0350ae832b45ea5440fa0bb2c495cd V=3 M=Authentication rejected"
(7) eap_peap: EAP-Message = 0x04590004
(7) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000
(7) eap_peap: Tunneled authentication was rejected
(7) eap_peap: FAILURE
(7) eap: Sending EAP Request (code 1) ID 90 length 46
(7) eap: EAP session adding &reply:State = 0xc1bbf9b5c6e1e0dc
(7) [eap] = handled
(7) } # authenticate = handled
(7) Using Post-Auth-Type Challenge
(7) Post-Auth-Type sub-section not found. Ignoring.
(7) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(7) session-state: Saving cached attributes
(7) Module-Failure-Message := "mschap: FAILED: No NT/LM-Password. Cannot perform authentication"
(7) Sent Access-Challenge Id 7 from 127.0.0.1:1812 to 127.0.0.1:49272 length 0
(7) EAP-Message = 0x015a002e19001703030023d19eb84f73fec696c8aa586a08d8b0bd48cc84e1b24cba9976661d89bedb4baf639a73
(7) Message-Authenticator = 0x00000000000000000000000000000000
(7) State = 0xc1bbf9b5c6e1e0dc9b5489cd06a27075
(7) Finished request
Waking up in 4.8 seconds.
(8) Received Access-Request Id 8 from 127.0.0.1:49272 to 127.0.0.1:1812 length 197
(8) User-Name = "anonymous at somedomain.tld"
(8) NAS-IP-Address = 127.0.0.1
(8) Calling-Station-Id = "02-00-00-00-00-01"
(8) Framed-MTU = 1400
(8) NAS-Port-Type = Wireless-802.11
(8) Service-Type = Framed-User
(8) Connect-Info = "CONNECT 11Mbps 802.11b"
(8) EAP-Message = 0x025a002e190017030300238dc5e34ca5e1709107fc6ca39122f88ed9b0a0d923a032407ee249892e689922fca3a8
(8) State = 0xc1bbf9b5c6e1e0dc9b5489cd06a27075
(8) Message-Authenticator = 0xb277522094b0529e3bb48cf80d5de393
(8) Restoring &session-state
(8) &session-state:Module-Failure-Message := "mschap: FAILED: No NT/LM-Password. Cannot perform authentication"
(8) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default
(8) authorize {
(8) policy filter_username {
(8) if (&User-Name) {
(8) if (&User-Name) -> TRUE
(8) if (&User-Name) {
(8) if (&User-Name =~ / /) {
(8) if (&User-Name =~ / /) -> FALSE
(8) if (&User-Name =~ /@[^@]*@/ ) {
(8) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
(8) if (&User-Name =~ /\.\./ ) {
(8) if (&User-Name =~ /\.\./ ) -> FALSE
(8) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(8) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE
(8) if (&User-Name =~ /\.$/) {
(8) if (&User-Name =~ /\.$/) -> FALSE
(8) if (&User-Name =~ /@\./) {
(8) if (&User-Name =~ /@\./) -> FALSE
(8) } # if (&User-Name) = notfound
(8) } # policy filter_username = notfound
(8) [preprocess] = ok
(8) [mschap] = noop
(8) [digest] = noop
(8) suffix: Checking for suffix after "@"
(8) suffix: Looking up realm "somedomain.tld" for User-Name = "anonymous at somedomain.tld"
(8) suffix: Found realm "somedomain.tld"
(8) suffix: Adding Stripped-User-Name = "anonymous"
(8) suffix: Adding Realm = "somedomain.tld"
(8) suffix: Authentication realm is LOCAL
(8) [suffix] = ok
(8) eap: Peer sent EAP Response (code 2) ID 90 length 46
(8) eap: Continuing tunnel setup
(8) [eap] = ok
(8) } # authorize = ok
(8) Found Auth-Type = eap
(8) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(8) authenticate {
(8) eap: Expiring EAP session with state 0xc1bbf9b5c6e1e0dc
(8) eap: Finished EAP session with state 0xc1bbf9b5c6e1e0dc
(8) eap: Previous EAP request found for state 0xc1bbf9b5c6e1e0dc, released from the list
(8) eap: Peer sent packet with method EAP PEAP (25)
(8) eap: Calling submodule eap_peap to process data
(8) eap_peap: Continuing EAP-TLS
(8) eap_peap: [eaptls verify] = ok
(8) eap_peap: Done initial handshake
(8) eap_peap: [eaptls process] = ok
(8) eap_peap: Session established. Decoding tunneled attributes
(8) eap_peap: PEAP state send tlv failure
(8) eap_peap: Received EAP-TLV response
(8) eap_peap: ERROR: The users session was previously rejected: returning reject (again.)
(8) eap_peap: This means you need to read the PREVIOUS messages in the debug output
(8) eap_peap: to find out the reason why the user was rejected
(8) eap_peap: Look for "reject" or "fail". Those earlier messages will tell you
(8) eap_peap: what went wrong, and how to fix the problem
(8) eap: ERROR: Failed continuing EAP PEAP (25) session. EAP sub-module failed
(8) eap: Sending EAP Failure (code 4) ID 90 length 4
(8) eap: Failed in EAP select
(8) [eap] = invalid
(8) } # authenticate = invalid
(8) Failed to authenticate the user
(8) Using Post-Auth-Type Reject
(8) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(8) Post-Auth-Type REJECT {
(8) sql: EXPAND .query
(8) sql: --> .query
(8) sql: Using query template 'query'
rlm_sql (sql): Reserved connection (4)
(8) sql: EXPAND %{User-Name}
(8) sql: --> anonymous at somedomain.tld
(8) sql: SQL-User-Name set to 'anonymous at somedomain.tld'
(8) sql: EXPAND INSERT INTO radpostauth (username, pass, reply, authdate) VALUES ( '%{SQL-User-Name}', '%{%{User-Password}:-%{Chap-Password}}', '%{reply:Packet-Type}', '%S')
(8) sql: --> INSERT INTO radpostauth (username, pass, reply, authdate) VALUES ( 'anonymous at somedomain.tld', '', 'Access-Reject', '2019-09-01 14:26:15')
(8) sql: Executing query: INSERT INTO radpostauth (username, pass, reply, authdate) VALUES ( 'anonymous at somedomain.tld', '', 'Access-Reject', '2019-09-01 14:26:15')
(8) sql: SQL query returned: success
(8) sql: 1 record(s) updated
rlm_sql (sql): Released connection (4)
Need 3 more connections to reach 10 spares
rlm_sql (sql): Opening additional connection (7), 1 of 25 pending slots used
rlm_sql_mysql: Starting connect to MySQL server
rlm_sql_mysql: Connected to database 'radius' on Localhost via UNIX socket, server version 10.3.15-MariaDB-1, protocol version 10
(8) [sql] = ok
(8) attr_filter.access_reject: EXPAND %{User-Name}
(8) attr_filter.access_reject: --> anonymous at somedomain.tld
(8) attr_filter.access_reject: Matched entry DEFAULT at line 11
(8) [attr_filter.access_reject] = updated
(8) [eap] = noop
(8) policy remove_reply_message_if_eap {
(8) if (&reply:EAP-Message && &reply:Reply-Message) {
(8) if (&reply:EAP-Message && &reply:Reply-Message) -> FALSE
(8) else {
(8) [noop] = noop
(8) } # else = noop
(8) } # policy remove_reply_message_if_eap = noop
(8) } # Post-Auth-Type REJECT = updated
(8) Delaying response for 1.000000 seconds
Waking up in 0.2 seconds.
Waking up in 0.7 seconds.
(8) Sending delayed response
(8) Sent Access-Reject Id 8 from 127.0.0.1:1812 to 127.0.0.1:49272 length 44
(8) EAP-Message = 0x045a0004
(8) Message-Authenticator = 0x00000000000000000000000000000000
Waking up in 3.7 seconds.
(0) Cleaning up request packet ID 0 with timestamp +46
(1) Cleaning up request packet ID 1 with timestamp +46
(2) Cleaning up request packet ID 2 with timestamp +46
(3) Cleaning up request packet ID 3 with timestamp +46
(4) Cleaning up request packet ID 4 with timestamp +46
(5) Cleaning up request packet ID 5 with timestamp +46
(6) Cleaning up request packet ID 6 with timestamp +46
Waking up in 0.1 seconds.
(7) Cleaning up request packet ID 7 with timestamp +46
Waking up in 0.1 seconds.
(8) Cleaning up request packet ID 8 with timestamp +46
Ready to process requests
More information about the Freeradius-Users
mailing list