Freeradius - LDAP Auth
online at berg-ner.de
online at berg-ner.de
Thu Dec 10 11:51:00 CET 2020
Hello!
thanks for the quick answer!
The Freeradius I want to set up in my company, so logically I have a domain and I also try to connect to the radius (via an access point) in the WLAN from the company.
Unfortunately I have no other choice but LDAP authentication. I need to get this to work.
> Am 10.12.2020 um 11:43 schrieb Michael Schwartzkopff <ms at sys4.de>:
>
> On 10.12.20 10:49, online at berg-ner.de <mailto:online at berg-ner.de> wrote:
>> Hello to everyone,
>>
>> after reading the whole internet and searching for solutions, but finding a solution in vain, I try my luck here.
>>
>> First of all, my goal: It should work quite simply. If you choose the WLAN you should be able to login with your LDAP - access data.
>>
>> After trying a lot of things, the same or even new errors will appear again and again.
>> The LDAP connection exists in any case. It finds the user in the exact OU. I tried it already with a certain group (so only if the user is in the group "wlan" he can login). He could also check the group.
>>
>> My question is: Is it because of some config that it does not work, or is it because of the domain controller?
>>
>> ldap.conf:
>> -----------------------------------------------------------------------------------------------
>> ldap {
>> server = "ldap://intranet.***.de <ldap://intranet.***.de> <ldap://intranet.***.de <ldap://intranet.***.de>>"
>> identity = "INTRANET\*USERNAME*"
>> password = "*******"
>> base_dn = "DC=intranet,DC=DC,DC=de"
>>
>> sasl {
>> }
>>
>> update {
>> control:Password-With-Header += 'userPassword'
>> control: += 'radiusControlAttribute'
>> request: += 'radiusRequestAttribute'
>> reply: += 'radiusReplyAttribute'
>> }
>>
>> user {
>> base_dn = "${..base_dn}"
>> filter = "(samaccountname=%{%{Stripped-User-Name}:-%{User-Name}})"
>> sasl {
>> }
>> }
>>
>> group {
>> base_dn = 'DC=intranet,DC=*DC*,DC=de'
>> filter = '(objectClass=posixGroup)'
>> scope = 'sub'
>> name_attribute = cn
>> membership_filter = "(member=%{control:Ldap-UserDn})"
>> membership_attribute = 'memberOf'
>> }
>>
>> Profile {
>> }
>>
>> client {
>> base_dn = "${..base_dn}"
>> filter = '(objectClass=radiusClient)'
>> template {
>> }
>> attribute {
>> ipaddr = 'radiusClientIdentifier'
>> secret = 'radiusClientSecret'
>> }
>> }
>>
>> accounting {
>> reference = "%{tolower:type.%{Acct-Status-Type}}"
>>
>> type {
>> start {
>> update {
>> description := "Online at %S"
>> }
>> }
>>
>> interim-update {
>> update {
>> description := "Last seen at %S"
>> }
>> }
>>
>> stop {
>> update {
>> description := "Offline at %S"
>> }
>> }
>> }
>> }
>>
>> post-auth {
>> update {
>> description := "Authenticated at %S"
>> }
>> }
>>
>> options {
>> chase_referrals = yes
>> rebind = yes
>> res_timeout = 10
>> srv_timelimit = 3
>> net_timeout = 1
>> idle = 60
>> probes = 3
>> interval = 3
>> ldap_debug = 0x0028
>> }
>>
>> Tls {
>> }
>>
>> pool {
>> start = ${thread[pool].start_servers}
>> min = ${thread[pool].min_spare_servers}
>> max = ${thread[pool].max_servers}
>> spare = ${thread[pool].max_spare_servers}
>> uses = 0
>> retry_delay = 30
>>
>> lifetime = 0
>> idle_timeout = 60
>> }
>> }
>>
>> -----------------------------------------------------------------------------------------------
>>
>> Site-enabled/default and Innertunnel:
>> -----------------------------------------------------------------------------------------------
>> The files are both still standard. The only thing I have added is:
>>
>> -ldap
>> if ((ok || updated) && User-Password && !control:Auth-Type) {
>> update {
>> control:Auth-Type := ldap
>> }
>> }
>>
>> In the authorize-section.
>> -----------------------------------------------------------------------------------------------
>>
>>
>> FREERADIUS -X:
>> -----------------------------------------------------------------------------------------------
>> (7) Received Access-Request Id 25 from *Accesspoint-IP* to *Radius-Server-IP:1812* length 371
>> (7) User-Name = "*USERNAME*"
>> (7) NAS-IP-Address = *AccessPoint-IP*
>> (7) NAS-Identifier = "TP-Link:B0-BE-76-24-73-FF"
>> (7) NAS-Port-Id = "00000001"
>> (7) Called-Station-Id = "B0-BE-76-24-73-FF:ldap_auth"
>> (7) NAS-Port-Type = Wireless-802.11
>> (7) Event-Timestamp = "Nov 25 2020 11:52:42 UTC"
>> (7) Service-Type = Framed-User
>> (7) Calling-Station-Id = "6A-95-50-D9-1B-DC"
>> (7) Connect-Info = "CONNECT 0Mbps 802.11b"
>> (7) Acct-Session-Id = "b0be762473ff-357FC6FB8137FBBA"
>> (7) Acct-Multi-Session-Id = "97193BFF112F1388"
>> (7) WLAN-Pairwise-Cipher = 1027076
>> (7) WLAN-Group-Cipher = 1027076
>> (7) WLAN-AKM-Suite = 1027073
>> (7) Framed-MTU = 1400
>> (7) EAP-Message = 0x0238006219001703030057b1de21bae8c7f5d43e9cefcb5c41ba58ac82f19aea43c4ed3c21feb1a2c3d6372f73a55132eb0157bf9792ab55d4ba3674125df5a3bdace00a31a870f5207823f75aaca3a15aa1ba23107d8ccd9cc1f0da3abd0f10c8cb
>> (7) State = 0x91de85df97e69c726c333a62068cc31c
>> (7) Message-Authenticator = 0xd2c7816cb5763af4c1102989e178783a
>> (7) Restoring &session-state
>> (7) &session-state:TLS-Session-Cipher-Suite = "ECDHE-RSA-AES256-GCM-SHA384"
>> (7) &session-state:TLS-Session-Version = "TLS 1.2"
>> (7) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default
>> (7) authorize {
>> (7) policy filter_username {
>> (7) if (&User-Name) {
>> (7) if (&User-Name) -> TRUE
>> (7) if (&User-Name) {
>> (7) if (&User-Name =~ / /) {
>> (7) if (&User-Name =~ / /) -> FALSE
>> (7) if (&User-Name =~ /@[^@]*@/ ) {
>> (7) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
>> (7) if (&User-Name =~ /\.\./ ) {
>> (7) if (&User-Name =~ /\.\./ ) -> FALSE
>> (7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
>> (7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE
>> (7) if (&User-Name =~ /\.$/) {
>> (7) if (&User-Name =~ /\.$/) -> FALSE
>> (7) if (&User-Name =~ /@\./) {
>> (7) if (&User-Name =~ /@\./) -> FALSE
>> (7) } # if (&User-Name) = notfound
>> (7) } # policy filter_username = notfound
>> (7) [preprocess] = ok
>> (7) [chap] = noop
>> (7) [mschap] = noop
>> (7) [digest] = noop
>> (7) suffix: Checking for suffix after "@"
>> (7) suffix: No '@' in User-Name = "*USERNAME*", looking up realm NULL
>> (7) suffix: No such realm "NULL"
>> (7) [suffix] = noop
>> (7) eap: Peer sent EAP Response (code 2) ID 56 length 98
>> (7) eap: Continuing tunnel setup
>> (7) [eap] = ok
>> (7) } # authorize = ok
>> (7) Found Auth-Type = eap
>> (7) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
>> (7) authenticate {
>> (7) eap: Expiring EAP session with state 0x6d94a36d6dacb9f9
>> (7) eap: Finished EAP session with state 0x91de85df97e69c72
>> (7) eap: Previous EAP request found for state 0x91de85df97e69c72, released from the list
>> (7) eap: Peer sent packet with method EAP PEAP (25)
>> (7) eap: Calling submodule eap_peap to process data
>> (7) eap_peap: Continuing EAP-TLS
>> (7) eap_peap: [eaptls verify] = ok
>> (7) eap_peap: Done initial handshake
>> (7) eap_peap: [eaptls process] = ok
>> (7) eap_peap: Session established. Decoding tunneled attributes
>> (7) eap_peap: PEAP state phase2
>> (7) eap_peap: EAP method MSCHAPv2 (26)
>> (7) eap_peap: Got tunneled request
>> (7) eap_peap: EAP-Message = 0x023800431a0238003e31976c2f5de49266406d03aa536085bfe2000000000000000079adbba2193c9312ebf9719bd0060b3fc13cdb7f8f7aeece00666c6f7269616e62
>> (7) eap_peap: Setting User-Name to *USERNAME*
>> (7) eap_peap: Sending tunneled request to inner-tunnel
>> (7) eap_peap: EAP-Message = 0x023800431a0238003e31976c2f5de49266406d03aa536085bfe2000000000000000079adbba2193c9312ebf9719bd0060b3fc13cdb7f8f7aeece00666c6f7269616e62
>> (7) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1
>> (7) eap_peap: User-Name = "*USERNAME*"
>> (7) eap_peap: State = 0x6d94a36d6dacb9f97126b7451b802a00
>> (7) Virtual server inner-tunnel received request
>> (7) EAP-Message = 0x023800431a0238003e31976c2f5de49266406d03aa536085bfe2000000000000000079adbba2193c9312ebf9719bd0060b3fc13cdb7f8f7aeece00666c6f7269616e62
>> (7) FreeRADIUS-Proxied-To = 127.0.0.1
>> (7) User-Name = "*USERNAME*"
>> (7) State = 0x6d94a36d6dacb9f97126b7451b802a00
>> (7) WARNING: Outer and inner identities are the same. User privacy is compromised.
>> (7) server inner-tunnel {
>> (7) session-state: No cached attributes
>> (7) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/inner-tunnel
>> (7) authorize {
>> (7) policy filter_username {
>> (7) if (&User-Name) {
>> (7) if (&User-Name) -> TRUE
>> (7) if (&User-Name) {
>> (7) if (&User-Name =~ / /) {
>> (7) if (&User-Name =~ / /) -> FALSE
>> (7) if (&User-Name =~ /@[^@]*@/ ) {
>> (7) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
>> (7) if (&User-Name =~ /\.\./ ) {
>> (7) if (&User-Name =~ /\.\./ ) -> FALSE
>> (7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
>> (7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE
>> (7) if (&User-Name =~ /\.$/) {
>> (7) if (&User-Name =~ /\.$/) -> FALSE
>> (7) if (&User-Name =~ /@\./) {
>> (7) if (&User-Name =~ /@\./) -> FALSE
>> (7) } # if (&User-Name) = notfound
>> (7) } # policy filter_username = notfound
>> (7) [chap] = noop
>> (7) [mschap] = noop
>> (7) suffix: Checking for suffix after "@"
>> (7) suffix: No '@' in User-Name = "*USERNAME*", looking up realm NULL
>> (7) suffix: No such realm "NULL"
>> (7) [suffix] = noop
>> (7) update control {
>> (7) &Proxy-To-Realm := LOCAL
>> (7) } # update control = noop
>> (7) eap: Peer sent EAP Response (code 2) ID 56 length 67
>> (7) eap: No EAP Start, assuming it's an on-going EAP conversation
>> (7) [eap] = updated
>> (7) [files] = noop
>> rlm_ldap (ldap): Reserved connection (1)
>> (7) ldap: EXPAND (samaccountname=%{%{Stripped-User-Name}:-%{User-Name}})
>> (7) ldap: --> (samaccountname=*USERNAME*)
>> (7) ldap: Performing search in "DC=INTRANET,DC=*DC*,DC=de" with filter "(samaccountname=*USERNAME*)", scope "sub"
>> (7) ldap: Waiting for search result...
>> rlm_ldap (ldap): Rebinding to URL ldap://ForestDnsZones.INTRANET.*domain*.de/DC=ForestDnsZones,DC=*DC*,DC=*DC*,DC=de <ldap://ForestDnsZones.INTRANET.*domain*.de/DC=ForestDnsZones,DC=*DC*,DC=*DC*,DC=de><ldap://ForestDnsZones.INTRANET.*domain*.de/DC=ForestDnsZones,DC=*DC*,DC=*DC*,DC=de <ldap://ForestDnsZones.INTRANET.*domain*.de/DC=ForestDnsZones,DC=*DC*,DC=*DC*,DC=de>>
>> rlm_ldap (ldap): Waiting for bind result...
>> rlm_ldap (ldap): Rebinding to URL ldap://DomainDnsZones.INTRANET.*domain*.de/DC=DomainDnsZones,DC=*DC*,DC=*DC*,DC=de <ldap://DomainDnsZones.INTRANET.*domain*.de/DC=DomainDnsZones,DC=*DC*,DC=*DC*,DC=de><ldap://DomainDnsZones.INTRANET.*domain*.de/DC=DomainDnsZones,DC=*DC*,DC=*DC*,DC=de <ldap://DomainDnsZones.INTRANET.*domain*.de/DC=DomainDnsZones,DC=*DC*,DC=*DC*,DC=de>>
>> rlm_ldap (ldap): Waiting for bind result...
>> rlm_ldap (ldap): Bind successful
>> rlm_ldap (ldap): Bind successful
>> (7) ldap: User object found at DN "CN=Name Surname,OU=*OU*,OU=*OU*,OU=*OU*,OU=*OU*,DC=*DC*,DC=*DC,DC=*DC*"
>> (7) ldap: Processing user attributes
>> (7) ldap: WARNING: No "known good" password added. Ensure the admin user has permission to read the password attribute
>> (7) ldap: WARNING: PAP authentication will *NOT* work with Active Directory (if that is what you were trying to configure)
>> rlm_ldap (ldap): Deleting connection (1) - Was referred to a different LDAP server
>> (7) [ldap] = ok
>> (7) if ((ok || updated) && User-Password && !control:Auth-Type) {
>> (7) if ((ok || updated) && User-Password && !control:Auth-Type) -> FALSE
>> (7) [expiration] = noop
>> (7) [logintime] = noop
>> (7) [pap] = noop
>> (7) } # authorize = updated
>> (7) Found Auth-Type = eap
>> (7) # Executing group from file /etc/freeradius/3.0/sites-enabled/inner-tunnel
>> (7) authenticate {
>> (7) eap: Expiring EAP session with state 0x6d94a36d6dacb9f9
>> (7) eap: Finished EAP session with state 0x6d94a36d6dacb9f9
>> (7) eap: Previous EAP request found for state 0x6d94a36d6dacb9f9, released from the list
>> (7) eap: Peer sent packet with method EAP MSCHAPv2 (26)
>> (7) eap: Calling submodule eap_mschapv2 to process data
>> (7) eap_mschapv2: # Executing group from file /etc/freeradius/3.0/sites-enabled/inner-tunnel
>> (7) eap_mschapv2: authenticate {
>> (7) mschap: WARNING: No Cleartext-Password configured. Cannot create NT-Password
>> (7) mschap: Creating challenge hash with username: *USERNAME*
>> (7) mschap: Client is using MS-CHAPv2
>> (7) mschap: ERROR: FAILED: No NT/LM-Password. Cannot perform authentication
>> (7) mschap: ERROR: MS-CHAP2-Response is incorrect
>> (7) eap_mschapv2: [mschap] = reject
>> (7) eap_mschapv2: } # authenticate = reject
>> (7) eap: Sending EAP Failure (code 4) ID 56 length 4
>> (7) eap: Freeing handler
>> (7) [eap] = reject
>> (7) } # authenticate = reject
>> (7) Failed to authenticate the user
>> (7) Using Post-Auth-Type Reject
>> (7) # Executing group from file /etc/freeradius/3.0/sites-enabled/inner-tunnel
>> (7) Post-Auth-Type REJECT {
>> (7) attr_filter.access_reject: EXPAND %{User-Name}
>> (7) attr_filter.access_reject: --> *USERNAME*
>> (7) attr_filter.access_reject: Matched entry DEFAULT at line 11
>> (7) [attr_filter.access_reject] = updated
>> (7) update outer.session-state {
>> (7) &Module-Failure-Message := &request:Module-Failure-Message -> 'mschap: FAILED: No NT/LM-Password. Cannot perform authentication'
>> (7) } # update outer.session-state = noop
>> (7) } # Post-Auth-Type REJECT = updated
>> (7) } # server inner-tunnel
>> (7) Virtual server sending reply
>> (7) MS-CHAP-Error = "8E=691 R=1 C=6d62be4a6a391d62280be8faba594674 V=3 M=Authentication rejected"
>> (7) EAP-Message = 0x04380004
>> (7) Message-Authenticator = 0x00000000000000000000000000000000
>> (7) eap_peap: Got tunneled reply code 3
>> (7) eap_peap: MS-CHAP-Error = "8E=691 R=1 C=6d62be4a6a391d62280be8faba594674 V=3 M=Authentication rejected"
>> (7) eap_peap: EAP-Message = 0x04380004
>> (7) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000
>> (7) eap_peap: Got tunneled reply RADIUS code 3
>> (7) eap_peap: MS-CHAP-Error = "8E=691 R=1 C=6d62be4a6a391d62280be8faba594674 V=3 M=Authentication rejected"
>> (7) eap_peap: EAP-Message = 0x04380004
>> (7) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000
>> (7) eap_peap: Tunneled authentication was rejected
>> (7) eap_peap: FAILURE
>> (7) eap: Sending EAP Request (code 1) ID 57 length 46
>> (7) eap: EAP session adding &reply:State = 0x91de85df96e79c72
>> (7) [eap] = handled
>> (7) } # authenticate = handled
>> (7) Using Post-Auth-Type Challenge
>> (7) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
>> (7) Challenge { ... } # empty sub-section is ignored
>> (7) session-state: Saving cached attributes
>> (7) TLS-Session-Cipher-Suite = "ECDHE-RSA-AES256-GCM-SHA384"
>> (7) TLS-Session-Version = "TLS 1.2"
>> (7) Module-Failure-Message := "mschap: FAILED: No NT/LM-Password. Cannot perform authentication"
>> (7) Sent Access-Challenge Id 25 from *Radius-Server-IP:1812* to *Accesspoint-IP* length 0
>> (7) EAP-Message = 0x0139002e1900170303002371c86c4f9605471aebfaa3b34ed5f06357d0eb547c2c853c97853ab157bee0b162981c
>> (7) Message-Authenticator = 0x00000000000000000000000000000000
>> (7) State = 0x91de85df96e79c726c333a62068cc31c
>> (7) Finished request
>> Waking up in 4.8 seconds.
>> (8) Received Access-Request Id 26 from *Accesspoint-IP* to *Radius-Server-IP:1812* length 319
>> (8) User-Name = "*USERNAME*"
>> (8) NAS-IP-Address = *AccessPoint-IP*
>> (8) NAS-Identifier = "TP-Link:B0-BE-76-24-73-FF"
>> (8) NAS-Port-Id = "00000001"
>> (8) Called-Station-Id = "B0-BE-76-24-73-FF:ldap_auth"
>> (8) NAS-Port-Type = Wireless-802.11
>> (8) Event-Timestamp = "Nov 25 2020 11:52:42 UTC"
>> (8) Service-Type = Framed-User
>> (8) Calling-Station-Id = "6A-95-50-D9-1B-DC"
>> (8) Connect-Info = "CONNECT 0Mbps 802.11b"
>> (8) Acct-Session-Id = "b0be762473ff-357FC6FB8137FBBA"
>> (8) Acct-Multi-Session-Id = "97193BFF112F1388"
>> (8) WLAN-Pairwise-Cipher = 1027076
>> (8) WLAN-Group-Cipher = 1027076
>> (8) WLAN-AKM-Suite = 1027073
>> (8) Framed-MTU = 1400
>> (8) EAP-Message = 0x0239002e19001703030023b1de21bae8c7f5d5fe5ace2f015bb1493cfc51fce39ec097cb3b7adc33072b2fd5928f
>> (8) State = 0x91de85df96e79c726c333a62068cc31c
>> (8) Message-Authenticator = 0xd60eadff0ff86f1364a45131245674c1
>> (8) Restoring &session-state
>> (8) &session-state:TLS-Session-Cipher-Suite = "ECDHE-RSA-AES256-GCM-SHA384"
>> (8) &session-state:TLS-Session-Version = "TLS 1.2"
>> (8) &session-state:Module-Failure-Message := "mschap: FAILED: No NT/LM-Password. Cannot perform authentication"
>> (8) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default
>> (8) authorize {
>> (8) policy filter_username {
>> (8) if (&User-Name) {
>> (8) if (&User-Name) -> TRUE
>> (8) if (&User-Name) {
>> (8) if (&User-Name =~ / /) {
>> (8) if (&User-Name =~ / /) -> FALSE
>> (8) if (&User-Name =~ /@[^@]*@/ ) {
>> (8) if (&User-Name =~ /@[^@]*@/ ) -> FALSE
>> (8) if (&User-Name =~ /\.\./ ) {
>> (8) if (&User-Name =~ /\.\./ ) -> FALSE
>> (8) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
>> (8) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE
>> (8) if (&User-Name =~ /\.$/) {
>> (8) if (&User-Name =~ /\.$/) -> FALSE
>> (8) if (&User-Name =~ /@\./) {
>> (8) if (&User-Name =~ /@\./) -> FALSE
>> (8) } # if (&User-Name) = notfound
>> (8) } # policy filter_username = notfound
>> (8) [preprocess] = ok
>> (8) [chap] = noop
>> (8) [mschap] = noop
>> (8) [digest] = noop
>> (8) suffix: Checking for suffix after "@"
>> (8) suffix: No '@' in User-Name = "*USERNAME*", looking up realm NULL
>> (8) suffix: No such realm "NULL"
>> (8) [suffix] = noop
>> (8) eap: Peer sent EAP Response (code 2) ID 57 length 46
>> (8) eap: Continuing tunnel setup
>> (8) [eap] = ok
>> (8) } # authorize = ok
>> (8) Found Auth-Type = eap
>> (8) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
>> (8) authenticate {
>> (8) eap: Expiring EAP session with state 0x91de85df96e79c72
>> (8) eap: Finished EAP session with state 0x91de85df96e79c72
>> (8) eap: Previous EAP request found for state 0x91de85df96e79c72, released from the list
>> (8) eap: Peer sent packet with method EAP PEAP (25)
>> (8) eap: Calling submodule eap_peap to process data
>> (8) eap_peap: Continuing EAP-TLS
>> (8) eap_peap: [eaptls verify] = ok
>> (8) eap_peap: Done initial handshake
>> (8) eap_peap: [eaptls process] = ok
>> (8) eap_peap: Session established. Decoding tunneled attributes
>> (8) eap_peap: PEAP state send tlv failure
>> (8) eap_peap: Received EAP-TLV response
>> (8) eap_peap: ERROR: The users session was previously rejected: returning reject (again.)
>> (8) eap_peap: This means you need to read the PREVIOUS messages in the debug output
>> (8) eap_peap: to find out the reason why the user was rejected
>> (8) eap_peap: Look for "reject" or "fail". Those earlier messages will tell you
>> (8) eap_peap: what went wrong, and how to fix the problem
>> (8) eap: ERROR: Failed continuing EAP PEAP (25) session. EAP sub-module failed
>> (8) eap: Sending EAP Failure (code 4) ID 57 length 4
>> (8) eap: Failed in EAP select
>> (8) [eap] = invalid
>> (8) } # authenticate = invalid
>> (8) Failed to authenticate the user
>> (8) Using Post-Auth-Type Reject
>> (8) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
>> (8) Post-Auth-Type REJECT {
>> (8) attr_filter.access_reject: EXPAND %{User-Name}
>> (8) attr_filter.access_reject: --> *USERNAME*
>> (8) attr_filter.access_reject: Matched entry DEFAULT at line 11
>> (8) [attr_filter.access_reject] = updated
>> (8) [eap] = noop
>> (8) policy remove_reply_message_if_eap {
>> (8) if (&reply:EAP-Message && &reply:Reply-Message) {
>> (8) if (&reply:EAP-Message && &reply:Reply-Message) -> FALSE
>> (8) else {
>> (8) [noop] = noop
>> (8) } # else = noop
>> (8) } # policy remove_reply_message_if_eap = noop
>> (8) } # Post-Auth-Type REJECT = updated
>> (8) Delaying response for 1.000000 seconds
>> Waking up in 0.3 seconds.
>> Waking up in 0.6 seconds.
>> (8) Sending delayed response
>> (8) Sent Access-Reject Id 26 from *Radius-Server-IP:1812* to *Accesspoint-IP* length 44
>> (8) EAP-Message = 0x04390004
>> (8) Message-Authenticator = 0x00000000000000000000000000000000
>> Waking up in 3.8 seconds.
>> (0) Cleaning up request packet ID 18 with timestamp +11
>> (1) Cleaning up request packet ID 19 with timestamp +11
>> (2) Cleaning up request packet ID 20 with timestamp +11
>> (3) Cleaning up request packet ID 21 with timestamp +11
>> (4) Cleaning up request packet ID 22 with timestamp +11
>> (5) Cleaning up request packet ID 23 with timestamp +11
>> (6) Cleaning up request packet ID 24 with timestamp +11
>> (7) Cleaning up request packet ID 25 with timestamp +11
>> (8) Cleaning up request packet ID 26 with timestamp +11
>> Ready to process requests
>>
>>
>>
>>
>>
>> Sincerely yours
>>
>> Florian Bergner
>> -
>> List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html <http://www.freeradius.org/list/users.html>
>
>
>
> Hi,
>
> only members of a domain can authenticate against AD. This only works
> with a local samba server on the radius server. See:
>
> https://wiki.freeradius.org/guide/FreeRADIUS-Active-Directory-Integration-HOWTO <https://wiki.freeradius.org/guide/FreeRADIUS-Active-Directory-Integration-HOWTO>
>
>
> You also could use a different backend (not AD). Then local
> authentication would work.
>
>
> Do not work against the system. Just see what works, and what does not.
>
> http://deployingradius.com/documents/protocols/compatibility.html <http://deployingradius.com/documents/protocols/compatibility.html>
>
> http://deployingradius.com/documents/protocols/oracles.html <http://deployingradius.com/documents/protocols/oracles.html>
>
>
> When you read carefully through your logs, than you will see where the
> problem is.
>
>
> Mit freundlichen Grüßen,
>
> --
>
> [*] sys4 AG
>
> https://sys4.de <https://sys4.de/>, +49 (89) 30 90 46 64
> Schleißheimer Straße 26/MG,80333 München
>
> Sitz der Gesellschaft: München, Amtsgericht München: HRB 199263
> Vorstand: Patrick Ben Koetter, Marc Schiffbauer, Wolfgang Stief
> Aufsichtsratsvorsitzender: Florian Kirstein
>
>
> -
> List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html <http://www.freeradius.org/list/users.html>
More information about the Freeradius-Users
mailing list