FreeRADIUS 3 Mac-Auth Issue
Taylor Hawkins
taylor.hawkins at exterro.com
Thu Jul 29 00:49:15 CEST 2021
Greetings,
Running FreeRADIUS Version 3.0.13 on CentOS7.
Referencing official Mac-Auth wiki page:
https://wiki.freeradius.org/guide/mac-auth
Per wiki, created/modified the below files:
- raddb/mods-available/files (replaced existing file per wiki instructions
with provided content)
- raddb/authorized_macs (created new file with my list of MAC addresses
with provided syntax)
- raddb/sites-available/default (added the canonicalisation policy and new
files call per wiki)
Running radius -X resulted in a deprecation warning of the compat line, and
an invalid syntax error for the files module.
Removing the compat line results in the debug output provided below, where
it states it was unable to find "files" as a module or policy as called in
the preacct section of the sites-enabled/default file.
This is the files module as it appears in mods-available and mods-enabled:
files authorized_macs {
# The default key attribute to use for matches. The content
# of this attribute is used to match the "name" of the
# entry.
key = %{Calling-Station-ID}
usersfile = ${confdir}/authorized_macs
}
This is the authorize section of default:
273 authorize {
274 preprocess
275
276 # If cleaning up the Calling-Station-Id...
277 rewrite_calling_station_id
278
279 # Now check against the authorized_macs file
280 authorized_macs
281
282 if (!ok) {
283 # No match was found, so reject
284 reject
285 }
286 else {
287 # The MAC address was found, so update Auth-Type
288 # to accept this auth.
289 update control {
290 Auth-Type := Accept
291 }
292 }
293 }
This is the preacct section of default:
400 preacct {
401 preprocess
402
403 #
404 # Merge Acct-[Input|Output]-Gigawords and
Acct-[Input-Output]-Octets
405 # into a single 64bit counter Acct-[Input|Output]-Octets64.
406 #
407 # acct_counters64
408
409 #
410 # Session start times are *implied* in RADIUS.
411 # The NAS never sends a "start time". Instead, it sends
412 # a start packet, *possibly* with an Acct-Delay-Time.
413 # The server is supposed to conclude that the start time
414 # was "Acct-Delay-Time" seconds in the past.
415 #
416 # The code below creates an explicit start time, which can
417 # then be used in other modules. It will be *mostly*
correct.
418 # Any errors are due to the 1-second resolution of RADIUS,
419 # and the possibility that the time on the NAS may be off.
420 #
421 # The start time is: NOW - delay - session_length
422 #
423
424 # update request {
425 # FreeRADIUS-Acct-Session-Start-Time = "%{expr: %l -
%{%{Acct-Session-Time}:-0} - %{%{Acct-Delay-Time}:-0}}"
426 # }
427
428
429 #
430 # Ensure that we have a semi-unique identifier for every
431 # request, and many NAS boxes are broken.
432 acct_unique
433
434 #
435 # Look for IPASS-style 'realm/', and if not found, look for
436 # '@realm', and decide whether or not to proxy, based on
437 # that.
438 #
439 # Accounting requests are generally proxied to the same
440 # home server as authentication requests.
441 # IPASS
442 suffix
443 # ntdomain
444
445 #
446 # Read the 'acct_users' file
447 files
448 }
Here is the debug log:
FreeRADIUS Version 3.0.13
Copyright (C) 1999-2017 The FreeRADIUS server project and contributors
There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A
PARTICULAR PURPOSE
You may redistribute copies of FreeRADIUS under the terms of the
GNU General Public License
For more information about these matters, see the file named COPYRIGHT
Starting - reading configuration files ...
including dictionary file /usr/share/freeradius/dictionary
including dictionary file /usr/share/freeradius/dictionary.dhcp
including dictionary file /usr/share/freeradius/dictionary.vqp
including dictionary file /etc/raddb/dictionary
including configuration file /etc/raddb/radiusd.conf
including configuration file /etc/raddb/proxy.conf
including configuration file /etc/raddb/clients.conf
including files in directory /etc/raddb/mods-enabled/
including configuration file /etc/raddb/mods-enabled/always
including configuration file /etc/raddb/mods-enabled/attr_filter
including configuration file /etc/raddb/mods-enabled/cache_eap
including configuration file /etc/raddb/mods-enabled/chap
including configuration file /etc/raddb/mods-enabled/date
including configuration file /etc/raddb/mods-enabled/detail
including configuration file /etc/raddb/mods-enabled/detail.log
including configuration file /etc/raddb/mods-enabled/dhcp
including configuration file /etc/raddb/mods-enabled/digest
including configuration file /etc/raddb/mods-enabled/dynamic_clients
including configuration file /etc/raddb/mods-enabled/eap
including configuration file /etc/raddb/mods-enabled/echo
including configuration file /etc/raddb/mods-enabled/exec
including configuration file /etc/raddb/mods-enabled/expiration
including configuration file /etc/raddb/mods-enabled/expr
including configuration file /etc/raddb/mods-enabled/files
including configuration file /etc/raddb/mods-enabled/linelog
including configuration file /etc/raddb/mods-enabled/logintime
including configuration file /etc/raddb/mods-enabled/mschap
including configuration file /etc/raddb/mods-enabled/ntlm_auth
including configuration file /etc/raddb/mods-enabled/pap
including configuration file /etc/raddb/mods-enabled/passwd
including configuration file /etc/raddb/mods-enabled/preprocess
including configuration file /etc/raddb/mods-enabled/radutmp
including configuration file /etc/raddb/mods-enabled/realm
including configuration file /etc/raddb/mods-enabled/replicate
including configuration file /etc/raddb/mods-enabled/soh
including configuration file /etc/raddb/mods-enabled/sradutmp
including configuration file /etc/raddb/mods-enabled/unix
including configuration file /etc/raddb/mods-enabled/unpack
including configuration file /etc/raddb/mods-enabled/utf8
including files in directory /etc/raddb/policy.d/
including configuration file /etc/raddb/policy.d/accounting
including configuration file /etc/raddb/policy.d/canonicalization
including configuration file /etc/raddb/policy.d/control
including configuration file /etc/raddb/policy.d/cui
including configuration file /etc/raddb/policy.d/debug
including configuration file /etc/raddb/policy.d/dhcp
including configuration file /etc/raddb/policy.d/eap
including configuration file /etc/raddb/policy.d/filter
including configuration file /etc/raddb/policy.d/operator-name
including files in directory /etc/raddb/sites-enabled/
including configuration file /etc/raddb/sites-enabled/default
including configuration file /etc/raddb/sites-enabled/inner-tunnel
main {
security {
user = "radiusd"
group = "radiusd"
allow_core_dumps = no
}
name = "radiusd"
prefix = "/usr"
localstatedir = "/var"
logdir = "/var/log/radius"
run_dir = "/var/run/radiusd"
}
main {
name = "radiusd"
prefix = "/usr"
localstatedir = "/var"
sbindir = "/usr/sbin"
logdir = "/var/log/radius"
run_dir = "/var/run/radiusd"
libdir = "/usr/lib64/freeradius"
radacctdir = "/var/log/radius/radacct"
hostname_lookups = no
max_request_time = 30
cleanup_delay = 5
max_requests = 16384
pidfile = "/var/run/radiusd/radiusd.pid"
checkrad = "/usr/sbin/checkrad"
debug_level = 0
proxy_requests = yes
log {
stripped_names = no
auth = no
auth_badpass = no
auth_goodpass = no
colourise = yes
msg_denied = "You are already logged in - access denied"
}
resources {
}
security {
max_attributes = 200
reject_delay = 1.000000
status_server = yes
}
}
radiusd: #### Loading Realms and Home Servers ####
proxy server {
retry_delay = 5
retry_count = 3
default_fallback = no
dead_time = 120
wake_all_if_all_dead = no
}
home_server localhost {
ipaddr = 127.0.0.1
port = 1812
type = "auth"
secret = <<< secret >>>
response_window = 20.000000
response_timeouts = 1
max_outstanding = 65536
zombie_period = 40
status_check = "status-server"
ping_interval = 30
check_interval = 30
check_timeout = 4
num_answers_to_alive = 3
revive_interval = 120
limit {
max_connections = 16
max_requests = 0
lifetime = 0
idle_timeout = 0
}
coa {
irt = 2
mrt = 16
mrc = 5
mrd = 30
}
}
home_server_pool my_auth_failover {
type = fail-over
home_server = localhost
}
realm example.com {
auth_pool = my_auth_failover
}
realm LOCAL {
}
radiusd: #### Loading Clients ####
client localhost {
ipaddr = 127.0.0.1
require_message_authenticator = no
secret = <<< secret >>>
nas_type = "other"
proto = "*"
limit {
max_connections = 16
lifetime = 0
idle_timeout = 30
}
}
client localhost_ipv6 {
ipv6addr = ::1
require_message_authenticator = no
secret = <<< secret >>>
limit {
max_connections = 16
lifetime = 0
idle_timeout = 30
}
}
Debugger not attached
# Creating Auth-Type = mschap
# Creating Auth-Type = digest
# Creating Auth-Type = eap
# Creating Auth-Type = PAP
# Creating Auth-Type = CHAP
# Creating Auth-Type = MS-CHAP
radiusd: #### Instantiating modules ####
modules {
# Loaded module rlm_always
# Loading module "reject" from file /etc/raddb/mods-enabled/always
always reject {
rcode = "reject"
simulcount = 0
mpp = no
}
# Loading module "fail" from file /etc/raddb/mods-enabled/always
always fail {
rcode = "fail"
simulcount = 0
mpp = no
}
# Loading module "ok" from file /etc/raddb/mods-enabled/always
always ok {
rcode = "ok"
simulcount = 0
mpp = no
}
# Loading module "handled" from file /etc/raddb/mods-enabled/always
always handled {
rcode = "handled"
simulcount = 0
mpp = no
}
# Loading module "invalid" from file /etc/raddb/mods-enabled/always
always invalid {
rcode = "invalid"
simulcount = 0
mpp = no
}
# Loading module "userlock" from file /etc/raddb/mods-enabled/always
always userlock {
rcode = "userlock"
simulcount = 0
mpp = no
}
# Loading module "notfound" from file /etc/raddb/mods-enabled/always
always notfound {
rcode = "notfound"
simulcount = 0
mpp = no
}
# Loading module "noop" from file /etc/raddb/mods-enabled/always
always noop {
rcode = "noop"
simulcount = 0
mpp = no
}
# Loading module "updated" from file /etc/raddb/mods-enabled/always
always updated {
rcode = "updated"
simulcount = 0
mpp = no
}
# Loaded module rlm_attr_filter
# Loading module "attr_filter.post-proxy" from file
/etc/raddb/mods-enabled/attr_filter
attr_filter attr_filter.post-proxy {
filename = "/etc/raddb/mods-config/attr_filter/post-proxy"
key = "%{Realm}"
relaxed = no
}
# Loading module "attr_filter.pre-proxy" from file
/etc/raddb/mods-enabled/attr_filter
attr_filter attr_filter.pre-proxy {
filename = "/etc/raddb/mods-config/attr_filter/pre-proxy"
key = "%{Realm}"
relaxed = no
}
# Loading module "attr_filter.access_reject" from file
/etc/raddb/mods-enabled/attr_filter
attr_filter attr_filter.access_reject {
filename = "/etc/raddb/mods-config/attr_filter/access_reject"
key = "%{User-Name}"
relaxed = no
}
# Loading module "attr_filter.access_challenge" from file
/etc/raddb/mods-enabled/attr_filter
attr_filter attr_filter.access_challenge {
filename = "/etc/raddb/mods-config/attr_filter/access_challenge"
key = "%{User-Name}"
relaxed = no
}
# Loading module "attr_filter.accounting_response" from file
/etc/raddb/mods-enabled/attr_filter
attr_filter attr_filter.accounting_response {
filename = "/etc/raddb/mods-config/attr_filter/accounting_response"
key = "%{User-Name}"
relaxed = no
}
# Loaded module rlm_cache
# Loading module "cache_eap" from file /etc/raddb/mods-enabled/cache_eap
cache cache_eap {
driver = "rlm_cache_rbtree"
key = "%{%{control:State}:-%{%{reply:State}:-%{State}}}"
ttl = 15
max_entries = 0
epoch = 0
add_stats = no
}
# Loaded module rlm_chap
# Loading module "chap" from file /etc/raddb/mods-enabled/chap
# Loaded module rlm_date
# Loading module "date" from file /etc/raddb/mods-enabled/date
date {
format = "%b %e %Y %H:%M:%S %Z"
}
# Loaded module rlm_detail
# Loading module "detail" from file /etc/raddb/mods-enabled/detail
detail {
filename =
"/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/detail-%Y%m%d"
header = "%t"
permissions = 384
locking = no
escape_filenames = no
log_packet_header = no
}
# Loading module "auth_log" from file /etc/raddb/mods-enabled/detail.log
detail auth_log {
filename =
"/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d"
header = "%t"
permissions = 384
locking = no
escape_filenames = no
log_packet_header = no
}
# Loading module "reply_log" from file /etc/raddb/mods-enabled/detail.log
detail reply_log {
filename =
"/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/reply-detail-%Y%m%d"
header = "%t"
permissions = 384
locking = no
escape_filenames = no
log_packet_header = no
}
# Loading module "pre_proxy_log" from file
/etc/raddb/mods-enabled/detail.log
detail pre_proxy_log {
filename =
"/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/pre-proxy-detail-%Y%m%d"
header = "%t"
permissions = 384
locking = no
escape_filenames = no
log_packet_header = no
}
# Loading module "post_proxy_log" from file
/etc/raddb/mods-enabled/detail.log
detail post_proxy_log {
filename =
"/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/post-proxy-detail-%Y%m%d"
header = "%t"
permissions = 384
locking = no
escape_filenames = no
log_packet_header = no
}
# Loaded module rlm_dhcp
# Loading module "dhcp" from file /etc/raddb/mods-enabled/dhcp
# Loaded module rlm_digest
# Loading module "digest" from file /etc/raddb/mods-enabled/digest
# Loaded module rlm_dynamic_clients
# Loading module "dynamic_clients" from file
/etc/raddb/mods-enabled/dynamic_clients
# Loaded module rlm_eap
# Loading module "eap" from file /etc/raddb/mods-enabled/eap
eap {
default_eap_type = "md5"
timer_expire = 60
ignore_unknown_eap_types = no
cisco_accounting_username_bug = no
max_sessions = 16384
}
# Loaded module rlm_exec
# Loading module "echo" from file /etc/raddb/mods-enabled/echo
exec echo {
wait = yes
program = "/bin/echo %{User-Name}"
input_pairs = "request"
output_pairs = "reply"
shell_escape = yes
}
# Loading module "exec" from file /etc/raddb/mods-enabled/exec
exec {
wait = no
input_pairs = "request"
shell_escape = yes
timeout = 10
}
# Loaded module rlm_expiration
# Loading module "expiration" from file /etc/raddb/mods-enabled/expiration
# Loaded module rlm_expr
# Loading module "expr" from file /etc/raddb/mods-enabled/expr
expr {
safe_characters =
"@abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789.-_:
/äéöüàâæçèéêëîïôœùûüaÿÄÉÖÜßÀÂÆÇÈÉÊËÎÏÔŒÙÛÜŸ"
}
# Loaded module rlm_files
# Loading module "authorized_macs" from file /etc/raddb/mods-enabled/files
files authorized_macs {
usersfile = "/etc/raddb/authorized_macs"
key = "%{Calling-Station-ID}"
}
# Loaded module rlm_linelog
# Loading module "linelog" from file /etc/raddb/mods-enabled/linelog
linelog {
filename = "/var/log/radius/linelog"
escape_filenames = no
syslog_severity = "info"
permissions = 384
format = "This is a log message for %{User-Name}"
reference = "messages.%{%{reply:Packet-Type}:-default}"
}
# Loading module "log_accounting" from file
/etc/raddb/mods-enabled/linelog
linelog log_accounting {
filename = "/var/log/radius/linelog-accounting"
escape_filenames = no
syslog_severity = "info"
permissions = 384
format = ""
reference = "Accounting-Request.%{%{Acct-Status-Type}:-unknown}"
}
# Loaded module rlm_logintime
# Loading module "logintime" from file /etc/raddb/mods-enabled/logintime
logintime {
minimum_timeout = 60
}
# Loaded module rlm_mschap
# Loading module "mschap" from file /etc/raddb/mods-enabled/mschap
mschap {
use_mppe = yes
require_encryption = no
require_strong = no
with_ntdomain_hack = yes
passchange {
}
allow_retry = yes
winbind_retry_with_normalised_username = no
}
# Loading module "ntlm_auth" from file /etc/raddb/mods-enabled/ntlm_auth
exec ntlm_auth {
wait = yes
program = "/path/to/ntlm_auth --request-nt-key --domain=MYDOMAIN
--username=%{mschap:User-Name} --password=%{User-Password}"
shell_escape = yes
}
# Loaded module rlm_pap
# Loading module "pap" from file /etc/raddb/mods-enabled/pap
pap {
normalise = yes
}
# Loaded module rlm_passwd
# Loading module "etc_passwd" from file /etc/raddb/mods-enabled/passwd
passwd etc_passwd {
filename = "/etc/passwd"
format = "*User-Name:Crypt-Password:"
delimiter = ":"
ignore_nislike = no
ignore_empty = yes
allow_multiple_keys = no
hash_size = 100
}
# Loaded module rlm_preprocess
# Loading module "preprocess" from file /etc/raddb/mods-enabled/preprocess
preprocess {
huntgroups = "/etc/raddb/mods-config/preprocess/huntgroups"
hints = "/etc/raddb/mods-config/preprocess/hints"
with_ascend_hack = no
ascend_channels_per_line = 23
with_ntdomain_hack = no
with_specialix_jetstream_hack = no
with_cisco_vsa_hack = no
with_alvarion_vsa_hack = no
}
# Loaded module rlm_radutmp
# Loading module "radutmp" from file /etc/raddb/mods-enabled/radutmp
radutmp {
filename = "/var/log/radius/radutmp"
username = "%{User-Name}"
case_sensitive = yes
check_with_nas = yes
permissions = 384
caller_id = yes
}
# Loaded module rlm_realm
# Loading module "IPASS" from file /etc/raddb/mods-enabled/realm
realm IPASS {
format = "prefix"
delimiter = "/"
ignore_default = no
ignore_null = no
}
# Loading module "suffix" from file /etc/raddb/mods-enabled/realm
realm suffix {
format = "suffix"
delimiter = "@"
ignore_default = no
ignore_null = no
}
# Loading module "realmpercent" from file /etc/raddb/mods-enabled/realm
realm realmpercent {
format = "suffix"
delimiter = "%"
ignore_default = no
ignore_null = no
}
# Loading module "ntdomain" from file /etc/raddb/mods-enabled/realm
realm ntdomain {
format = "prefix"
delimiter = "\\"
ignore_default = no
ignore_null = no
}
# Loaded module rlm_replicate
# Loading module "replicate" from file /etc/raddb/mods-enabled/replicate
# Loaded module rlm_soh
# Loading module "soh" from file /etc/raddb/mods-enabled/soh
soh {
dhcp = yes
}
# Loading module "sradutmp" from file /etc/raddb/mods-enabled/sradutmp
radutmp sradutmp {
filename = "/var/log/radius/sradutmp"
username = "%{User-Name}"
case_sensitive = yes
check_with_nas = yes
permissions = 420
caller_id = no
}
# Loaded module rlm_unix
# Loading module "unix" from file /etc/raddb/mods-enabled/unix
unix {
radwtmp = "/var/log/radius/radwtmp"
}
Creating attribute Unix-Group
# Loaded module rlm_unpack
# Loading module "unpack" from file /etc/raddb/mods-enabled/unpack
# Loaded module rlm_utf8
# Loading module "utf8" from file /etc/raddb/mods-enabled/utf8
instantiate {
}
# Instantiating module "reject" from file /etc/raddb/mods-enabled/always
# Instantiating module "fail" from file /etc/raddb/mods-enabled/always
# Instantiating module "ok" from file /etc/raddb/mods-enabled/always
# Instantiating module "handled" from file /etc/raddb/mods-enabled/always
# Instantiating module "invalid" from file /etc/raddb/mods-enabled/always
# Instantiating module "userlock" from file /etc/raddb/mods-enabled/always
# Instantiating module "notfound" from file /etc/raddb/mods-enabled/always
# Instantiating module "noop" from file /etc/raddb/mods-enabled/always
# Instantiating module "updated" from file /etc/raddb/mods-enabled/always
# Instantiating module "attr_filter.post-proxy" from file
/etc/raddb/mods-enabled/attr_filter
reading pairlist file /etc/raddb/mods-config/attr_filter/post-proxy
# Instantiating module "attr_filter.pre-proxy" from file
/etc/raddb/mods-enabled/attr_filter
reading pairlist file /etc/raddb/mods-config/attr_filter/pre-proxy
# Instantiating module "attr_filter.access_reject" from file
/etc/raddb/mods-enabled/attr_filter
reading pairlist file /etc/raddb/mods-config/attr_filter/access_reject
[/etc/raddb/mods-config/attr_filter/access_reject]:11 Check item
"FreeRADIUS-Response-Delay" found in filter list for realm "DEFAULT".
[/etc/raddb/mods-config/attr_filter/access_reject]:11 Check item
"FreeRADIUS-Response-Delay-USec" found in filter list for realm
"DEFAULT".
# Instantiating module "attr_filter.access_challenge" from file
/etc/raddb/mods-enabled/attr_filter
reading pairlist file /etc/raddb/mods-config/attr_filter/access_challenge
# Instantiating module "attr_filter.accounting_response" from file
/etc/raddb/mods-enabled/attr_filter
reading pairlist file /etc/raddb/mods-config/attr_filter/accounting_response
# Instantiating module "cache_eap" from file
/etc/raddb/mods-enabled/cache_eap
rlm_cache (cache_eap): Driver rlm_cache_rbtree (module rlm_cache_rbtree)
loaded and linked
# Instantiating module "detail" from file /etc/raddb/mods-enabled/detail
# Instantiating module "auth_log" from file
/etc/raddb/mods-enabled/detail.log
rlm_detail (auth_log): 'User-Password' suppressed, will not appear in
detail output
# Instantiating module "reply_log" from file
/etc/raddb/mods-enabled/detail.log
# Instantiating module "pre_proxy_log" from file
/etc/raddb/mods-enabled/detail.log
# Instantiating module "post_proxy_log" from file
/etc/raddb/mods-enabled/detail.log
# Instantiating module "eap" from file /etc/raddb/mods-enabled/eap
# Linked to sub-module rlm_eap_md5
# Linked to sub-module rlm_eap_leap
# Linked to sub-module rlm_eap_gtc
gtc {
challenge = "Password: "
auth_type = "PAP"
}
# Linked to sub-module rlm_eap_tls
tls {
tls = "tls-common"
}
tls-config tls-common {
verify_depth = 0
ca_path = "/etc/raddb/certs"
pem_file_type = yes
private_key_file = "/etc/raddb/certs/server.pem"
certificate_file = "/etc/raddb/certs/server.pem"
ca_file = "/etc/raddb/certs/ca.pem"
private_key_password = <<< secret >>>
dh_file = "/etc/raddb/certs/dh"
fragment_size = 1024
include_length = yes
auto_chain = yes
check_crl = no
check_all_crl = no
cipher_list = "DEFAULT"
cipher_server_preference = no
ecdh_curve = "prime256v1"
cache {
enable = no
lifetime = 24
max_entries = 255
}
verify {
skip_if_ocsp_ok = no
}
ocsp {
enable = no
override_cert_url = yes
url = "http://127.0.0.1/ocsp/"
use_nonce = yes
timeout = 0
softfail = no
}
}
# Linked to sub-module rlm_eap_ttls
ttls {
tls = "tls-common"
default_eap_type = "md5"
copy_request_to_tunnel = no
use_tunneled_reply = no
virtual_server = "inner-tunnel"
include_length = yes
require_client_cert = no
}
tls: Using cached TLS configuration from previous invocation
# Linked to sub-module rlm_eap_peap
peap {
tls = "tls-common"
default_eap_type = "mschapv2"
copy_request_to_tunnel = no
use_tunneled_reply = no
proxy_tunneled_request_as_eap = yes
virtual_server = "inner-tunnel"
soh = no
require_client_cert = no
}
tls: Using cached TLS configuration from previous invocation
# Linked to sub-module rlm_eap_mschapv2
mschapv2 {
with_ntdomain_hack = no
send_error = no
}
# Instantiating module "expiration" from file
/etc/raddb/mods-enabled/expiration
# Instantiating module "authorized_macs" from file
/etc/raddb/mods-enabled/files
reading pairlist file /etc/raddb/authorized_macs
# Instantiating module "linelog" from file /etc/raddb/mods-enabled/linelog
# Instantiating module "log_accounting" from file
/etc/raddb/mods-enabled/linelog
# Instantiating module "logintime" from file
/etc/raddb/mods-enabled/logintime
# Instantiating module "mschap" from file /etc/raddb/mods-enabled/mschap
rlm_mschap (mschap): using internal authentication
# Instantiating module "pap" from file /etc/raddb/mods-enabled/pap
# Instantiating module "etc_passwd" from file
/etc/raddb/mods-enabled/passwd
rlm_passwd: nfields: 3 keyfield 0(User-Name) listable: no
# Instantiating module "preprocess" from file
/etc/raddb/mods-enabled/preprocess
reading pairlist file /etc/raddb/mods-config/preprocess/huntgroups
reading pairlist file /etc/raddb/mods-config/preprocess/hints
# Instantiating module "IPASS" from file /etc/raddb/mods-enabled/realm
# Instantiating module "suffix" from file /etc/raddb/mods-enabled/realm
# Instantiating module "realmpercent" from file
/etc/raddb/mods-enabled/realm
# Instantiating module "ntdomain" from file /etc/raddb/mods-enabled/realm
} # modules
radiusd: #### Loading Virtual Servers ####
server { # from file /etc/raddb/radiusd.conf
} # server
server default { # from file /etc/raddb/sites-enabled/default
# Loading authenticate {...}
# Loading authorize {...}
# Loading preacct {...}
/etc/raddb/sites-enabled/default[447]: Failed to find "files" as a module
or policy.
/etc/raddb/sites-enabled/default[447]: Please verify that the configuration
exists in /etc/raddb/mods-enabled/files.
/etc/raddb/sites-enabled/default[400]: Errors parsing preacct section.
Any assistance is greatly appreciated.
Thanks,
Taylor
More information about the Freeradius-Users
mailing list