Hello, I am trying to use mysql and Freeradius for AAA. The communication between freeradius and mysql server seems OK, since Freeradius is getting the clients from radclients table. When I do a test from the command line: "radtest user1 pass localhost 1812 shared" I got the output: "rad_recv: Access-Request packet from host 127.0.0.1 port 56962, id=152, length=57 User-Name = "user1" User-Password = "pass" NAS-IP-Address = 127.0.1.1 NAS-Port = 1812 Mon Feb 16 17:22:09 2009 : Info: No authenticate method (Auth-Type) configuration found for the request: Rejecting the user Mon Feb 16 17:22:09 2009 : Info: Failed to authenticate the user. Mon Feb 16 17:22:09 2009 : Info: Using Post-Auth-Type Reject Mon Feb 16 17:22:09 2009 : Debug: WARNING: Unknown value specified for Post-Auth-Type. Cannot perform requested action. Mon Feb 16 17:22:09 2009 : Info: Delaying reject of request 1 for 1 seconds Mon Feb 16 17:22:09 2009 : Debug: Going to the next request Mon Feb 16 17:22:09 2009 : Debug: Waking up in 0.9 seconds. Mon Feb 16 17:22:11 2009 : Info: Sending delayed reject for request 1 Sending Access-Reject of id 152 to 127.0.0.1 port 56962 Mon Feb 16 17:22:11 2009 : Debug: Waking up in 4.9 seconds. " Following is my configuration file(please note that this is only the file in sites-avaiable dir, note radiusd.conf): "###################################################################### # # As of 2.0.0, FreeRADIUS supports virtual hosts using the # "server" section, and configuration directives. # # Virtual hosts should be put into the "sites-available" # directory. Soft links should be created in the "sites-enabled" # directory to these files. This is done in a normal installation. # # $Id$ # ###################################################################### # # Read "man radiusd" before editing this file. See the section # titled DEBUGGING. It outlines a method where you can quickly # obtain the configuration you want, without running into # trouble. See also "man unlang", which documents the format # of this file. # # This configuration is designed to work in the widest possible # set of circumstances, with the widest possible number of # authentication methods. This means that in general, you should # need to make very few changes to this file. # # The best way to configure the server for your local system # is to CAREFULLY edit this file. Most attempts to make large # edits to this file will BREAK THE SERVER. Any edits should # be small, and tested by running the server with "radiusd -X". # Once the edits have been verified to work, save a copy of these # configuration files somewhere. (e.g. as a "tar" file). Then, # make more edits, and test, as above. # # There are many "commented out" references to modules such # as ldap, sql, etc. These references serve as place-holders. # If you need the functionality of that module, then configure # it in radiusd.conf, and un-comment the references to it in # this file. In most cases, those small changes will result # in the server being able to connect to the DB, and to # authenticate users. # ###################################################################### server intelitiva.com { # # In 1.x, the "authorize", etc. sections were global in # radiusd.conf. As of 2.0, they SHOULD be in a server section. # # The server section with no virtual server name is the "default" # section. It is used when no server name is specified. # # We don't indent the rest of this file, because doing so # would make it harder to read. # # Authorization. First preprocess (hints and huntgroups files), # then realms, and finally look in the "users" file. # # The order of the realm modules will determine the order that # we try to find a matching realm. # # Make *sure* that 'preprocess' comes before any realm if you # need to setup hints for the remote radius server authorize { # # The preprocess module takes care of sanitizing some bizarre # attributes in the request, and turning them into attributes # which are more standard. # # It takes care of processing the 'raddb/hints' and the # 'raddb/huntgroups' files. # # It also adds the %{Client-IP-Address} attribute to the request. preprocess # # If you want to have a log of authentication requests, # un-comment the following line, and the 'detail auth_log' # section, above. #auth_log # # The chap module will set 'Auth-Type := CHAP' if we are # handling a CHAP request and Auth-Type has not already been set chap # # If the users are logging in with an MS-CHAP-Challenge # attribute for authentication, the mschap module will find # the MS-CHAP-Challenge attribute, and add 'Auth-Type := MS-CHAP' # to the request, which will cause the server to then use # the mschap module for authentication. mschap # # If you have a Cisco SIP server authenticating against # FreeRADIUS, uncomment the following line, and the 'digest' # line in the 'authenticate' section. # digest # # Look for IPASS style 'realm/', and if not found, look for # '@realm', and decide whether or not to proxy, based on # that. # IPASS # # If you are using multiple kinds of realms, you probably # want to set "ignore_null = yes" for all of them. # Otherwise, when the first style of realm doesn't match, # the other styles won't be checked. # # suffix # ntdomain # # This module takes care of EAP-MD5, EAP-TLS, and EAP-LEAP # authentication. # # It also sets the EAP-Type attribute in the request # attribute list to the EAP type from the packet. # # As of 2.0, the EAP module returns "ok" in the authorize stage # for TTLS and PEAP. In 1.x, it never returned "ok" here, so # this change is compatible with older configurations. # # The example below uses module failover to avoid querying all # of the following modules if the EAP module returns "ok". # Therefore, your LDAP and/or SQL servers will not be queried # for the many packets that go back and forth to set up TTLS # or PEAP. The load on those servers will therefore be reduced. # # eap { # ok = return # } # # Look in an SQL database. The schema of the database # is meant to mirror the "users" file. # # See "Authorization Queries" in sql.conf sql # # Pull crypt'd passwords from /etc/passwd or /etc/shadow, # using the system API's to get the password. If you want # to read /etc/passwd or /etc/shadow directly, see the # passwd module in radiusd.conf. # # unix # # Read the 'users' file # files # # If you are using /etc/smbpasswd, and are also doing # mschap authentication, the un-comment this line, and # configure the 'etc_smbpasswd' module, above. # etc_smbpasswd # # The ldap module will set Auth-Type to LDAP if it has not # already been set # ldap # # Enforce daily limits on time spent logged in. # daily # # Use the checkval module # checkval # expiration # logintime # # If no other module has claimed responsibility for # authentication, then try to use PAP. This allows the # other modules listed above to add a "known good" password # to the request, and to do nothing else. The PAP module # will then see that password, and use it to do PAP # authentication. # # This module should be listed last, so that the other modules # get a chance to set Auth-Type for themselves. # # pap # # If "status_server = yes", then Status-Server messages are passed # through the following section, and ONLY the following section. # This permits you to do DB queries, for example. If the modules # listed here return "fail", then NO response is sent. # # Autz-Type Status-Server { # # } } # Authentication. # # # This section lists which modules are available for authentication. # Note that it does NOT mean 'try each module in order'. It means # that a module from the 'authorize' section adds a configuration # attribute 'Auth-Type := FOO'. That authentication type is then # used to pick the apropriate module from the list below. # # In general, you SHOULD NOT set the Auth-Type attribute. The server # will figure it out on its own, and will do the right thing. The # most common side effect of erroneously setting the Auth-Type # attribute is that one authentication method will work, but the # others will not. # # The common reasons to set the Auth-Type attribute by hand # is to either forcibly reject the user (Auth-Type := Reject), # or to or forcibly accept the user (Auth-Type := Accept). # # Note that Auth-Type := Accept will NOT work with EAP. # # Please do not put "unlang" configurations into the "authenticate" # section. Put them in the "post-auth" section instead. That's what # the post-auth section is for. # authenticate { # # PAP authentication, when a back-end database listed # in the 'authorize' section supplies a password. The # password can be clear-text, or encrypted. Auth-Type PAP { pap } # # Most people want CHAP authentication # A back-end database listed in the 'authorize' section # MUST supply a CLEAR TEXT password. Encrypted passwords # won't work. Auth-Type CHAP { chap } # # MSCHAP authentication. Auth-Type MS-CHAP { mschap } # # If you have a Cisco SIP server authenticating against # FreeRADIUS, uncomment the following line, and the 'digest' # line in the 'authorize' section. # digest # # Pluggable Authentication Modules. # pam # # See 'man getpwent' for information on how the 'unix' # module checks the users password. Note that packets # containing CHAP-Password attributes CANNOT be authenticated # against /etc/passwd! See the FAQ for details. # # unix # Uncomment it if you want to use ldap for authentication # # Note that this means "check plain-text password against # the ldap database", which means that EAP won't work, # as it does not supply a plain-text password. # Auth-Type LDAP { # ldap # } # # Allow EAP authentication. # eap } # # Pre-accounting. Decide which accounting type to use. # preacct { preprocess # # Ensure that we have a semi-unique identifier for every # request, and many NAS boxes are broken. acct_unique # # Look for IPASS-style 'realm/', and if not found, look for # '@realm', and decide whether or not to proxy, based on # that. # # Accounting requests are generally proxied to the same # home server as authentication requests. # IPASS suffix # ntdomain # # Read the 'acct_users' file files } # # Accounting. Log the accounting data. # accounting { # # Create a 'detail'ed log of the packets. # Note that accounting requests which are proxied # are also logged in the detail file. detail # daily # Update the wtmp file # # If you don't use "radlast", you can delete this line. unix # # For Simultaneous-Use tracking. # # Due to packet losses in the network, the data here # may be incorrect. There is little we can do about it. radutmp # sradutmp # Return an address to the IP Pool when we see a stop record. # main_pool # # Log traffic to an SQL database. # # See "Accounting queries" in sql.conf sql # # Instead of sending the query to the SQL server, # write it into a log file. # # sql_log # Cisco VoIP specific bulk accounting # pgsql-voip # Filter attributes from the accounting response. attr_filter.accounting_response # # See "Autz-Type Status-Server" for how this works. # # Acct-Type Status-Server { # # } } # Session database, used for checking Simultaneous-Use. Either the radutmp # or rlm_sql module can handle this. # The rlm_sql module is *much* faster session { radutmp # # See "Simultaneous Use Checking Queries" in sql.conf sql } # Post-Authentication # Once we KNOW that the user has been authenticated, there are # additional steps we can take. post-auth { # Get an address from the IP Pool. # main_pool # # If you want to have a log of authentication replies, # un-comment the following line, and the 'detail reply_log' # section, above. # reply_log # # After authenticating the user, do another SQL query. # # See "Authentication Logging Queries" in sql.conf sql # # Instead of sending the query to the SQL server, # write it into a log file. # # sql_log # # Un-comment the following if you have set # 'edir_account_policy_check = yes' in the ldap module sub-section of # the 'modules' section. # # ldap exec # # Access-Reject packets are sent through the REJECT sub-section of the # post-auth section. # # Add the ldap module name (or instance) if you have set # 'edir_account_policy_check = yes' in the ldap module configuration # Post-Auth-Type REJECT { attr_filter.access_reject } } # # When the server decides to proxy a request to a home server, # the proxied request is first passed through the pre-proxy # stage. This stage can re-write the request, or decide to # cancel the proxy. # # Only a few modules currently have this method. # pre-proxy { # attr_rewrite # Uncomment the following line if you want to change attributes # as defined in the preproxy_users file. # files # Uncomment the following line if you want to filter requests # sent to remote servers based on the rules defined in the # 'attrs.pre-proxy' file. # attr_filter.pre-proxy # If you want to have a log of packets proxied to a home # server, un-comment the following line, and the # 'detail pre_proxy_log' section, above. # pre_proxy_log } # # When the server receives a reply to a request it proxied # to a home server, the request may be massaged here, in the # post-proxy stage. # post-proxy { # If you want to have a log of replies from a home server, # un-comment the following line, and the 'detail post_proxy_log' # section, above. # post_proxy_log # attr_rewrite # Uncomment the following line if you want to filter replies from # remote proxies based on the rules defined in the 'attrs' file. # attr_filter.post-proxy # # If you are proxying LEAP, you MUST configure the EAP # module, and you MUST list it here, in the post-proxy # stage. # # You MUST also use the 'nostrip' option in the 'realm' # configuration. Otherwise, the User-Name attribute # in the proxied request will not match the user name # hidden inside of the EAP packet, and the end server will # reject the EAP request. # eap # # If the server tries to proxy a request and fails, then the # request is processed through the modules in this section. # # The main use of this section is to permit robust proxying # of accounting packets. The server can be configured to # proxy accounting packets as part of normal processing. # Then, if the home server goes down, accounting packets can # be logged to a local "detail" file, for processing with # radrelay. When the home server comes back up, radrelay # will read the detail file, and send the packets to the # home server. # # With this configuration, the server always responds to # Accounting-Requests from the NAS, but only writes # accounting packets to disk if the home server is down. # # Post-Proxy-Type Fail { # detail # } } }" Any ideas? Thanks in advance, Pedro Mazzoni