I ran Freeradius in debug mode already to check this: rad_recv: Access-Request packet from host 192.168.1.170 port 3098, id=201, length=286 User-Name = "krijn" NAS-Identifier = "00-0b-6b-4f-80-65:isiline" NAS-IP-Address = 192.168.1.170 NAS-Port = 5 NAS-Port-Id = "ath0" NAS-Port-Type = Wireless-802.11 Service-Type = Framed-User Framed-MTU = 1400 Called-Station-Id = "00-0B-6B-4F-80-65:isiline" Calling-Station-Id = "00-0B-6B-D9-D0-14" Event-Timestamp = "Oct 4 2010 19:10:41 CEST" WISPr-Location-ID = "isocc=(null),cc=(null),ac=(null),network=(null)" WISPr-Location-Name = "(null),(null)" Connect-Info = "CONNECT 11Mbps 802.11b" EAP-Message = 0x020100060319 State = 0x697a4088697b55320faa946fa7f606af Message-Authenticator = 0x73ade7409a1c7def5027792de162bd0b Met vriendelijke groet/Kind regards,   Krijn Tanis WiMood Kerkstraat 8/10 3252 AX  Goedereede   Tel.: +31 (0) 187 82 0204 Fax: +31 (0) 187 49 1596 Mob.: +31 (0) 6 10923259 Mail: info@wimood.nl Web: http://www.wimood.nl -----Oorspronkelijk bericht----- Van: freeradius-users-bounces+krijntanis=wimood.nl@lists.freeradius.org [mailto:freeradius-users-bounces+krijntanis=wimood.nl@lists.freeradius.org] Namens Tim Sylvester Verzonden: maandag 4 oktober 2010 20:16 Aan: 'FreeRadius users mailing list' Onderwerp: RE: Check multiple attributes for one user Run the server in debug mode (radiusd -X) and check the attributes sent by the NAS. The NAS may not be sending the Calling-Station-Id or it may be in a different format. Either way, the debug output is going to give you more information. Tim

-----Original Message----- From: freeradius-users- bounces+tim.sylvester=networkradius.com@lists.freeradius.org [mailto:freeradius-users- bounces+tim.sylvester=networkradius.com@lists.freeradius.org] On bounces+Behalf Of Krijn Tanis | WiMood Sent: Monday, October 04, 2010 10:59 AM To: freeradius-users@lists.freeradius.org Subject: Check multiple attributes for one user

Hello all,

For a project I am working on 802.1x WPA-EAP authentication and for this I use a Freeradius server. This part of authentication works perfect.

Now I also want to check the Calling-Station-Id for the user, in this case it is MAC address of the wireless client. I want this because I want to allow the user to connect only from one MAC address (else user is able to use a other device that is not in our control, I want to prevent this. So I want to check the Password and Calling-Station-Id in one and the same Access Request. If both match an Access-Accept is sent, in all other cases (when password or Calling-Station-Id do not match for the user) an Access-Reject.

I tried to do this:

+----+----------------+--------------------+------------------+------+ | id | UserName | Attribute | Value | Op | +----+----------------+--------------------+------------------+------+ | 1 | krijn | Calling-Station-Id | 00-0B-6B-D9-D0-14| == | | 2 | krijn | Cleartext-Password | test123 | := |

But this doesnt work, the user is rejected. Can somebody point me into the right direction?

Kind regards,

Krijn Tanis WiMood

- List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html

The Radius debug output: =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2010.10.05 08:53:37 =~=~=~=~=~=~=~=~=~=~=~= freeradius -X FreeRADIUS Version 2.1.8, for host i486-pc-linux-gnu, built on Jan 5 2010 at 02:49:11 Copyright (C) 1999-2009 The FreeRADIUS server project and contributors. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. You may redistribute copies of FreeRADIUS under the terms of the GNU General Public License v2. Starting - reading configuration files ... including configuration file /etc/freeradius/radiusd.conf including configuration file /etc/freeradius/proxy.conf including configuration file /etc/freeradius/clients.conf including files in directory /etc/freeradius/modules/ including configuration file /etc/freeradius/modules/ippool including configuration file /etc/freeradius/modules/echo including configuration file /etc/freeradius/modules/passwd including configuration file /etc/freeradius/modules/pam including configuration file /etc/freeradius/modules/sradutmp including configuration file /etc/freeradius/modules/ntlm_auth including configuration file /etc/freeradius/modules/smbpasswd including configuration file /etc/freeradius/modules/detail including configuration file /etc/freeradius/modules/attr_filter including configuration file /etc/freeradius/modules/krb5 including configuration file /etc/freeradius/modules/mac2vlan including configuration file /etc/freeradius/modules/unix including configuration file /etc/freeradius/modules/checkval including configuration file /etc/freeradius/modules/etc_group including configuration file /etc/freeradius/modules/smsotp including configuration file /etc/freeradius/modules/inner-eap including configuration file /etc/freeradius/modules/attr_rewrite including configuration file /etc/freeradius/modules/policy including configuration file /etc/freeradius/modules/counter including configuration file /etc/freeradius/modules/sql_log including configuration file /etc/freeradius/modules/radutmp including configuration file /etc/freeradius/modules/realm including configuration file /etc/freeradius/modules/perl including configuration file /etc/freeradius/modules/otp including configuration file /etc/freeradius/modules/ldap including configuration file /etc/freeradius/modules/chap including configuration file /etc/freeradius/modules/digest including configuration file /etc/freeradius/modules/cui including configuration file /etc/freeradius/modules/preprocess including configuration file /etc/freeradius/modules/pap including configuration file /etc/freeradius/modules/sqlcounter_expire_on_login including configuration file /etc/freeradius/modules/exec including configuration file /etc/freeradius/modules/expr including configuration file /etc/freeradius/modules/detail.example.com including configuration file /etc/freeradius/modules/wimax including configuration file /etc/freeradius/modules/detail.log including configuration file /etc/freeradius/modules/files including configuration file /etc/freeradius/modules/mac2ip including configuration file /etc/freeradius/modules/mschap including configuration file /etc/freeradius/modules/logintime including configuration file /etc/freeradius/modules/expiration including configuration file /etc/freeradius/modules/always including configuration file /etc/freeradius/modules/linelog including configuration file /etc/freeradius/modules/acct_unique including configuration file /etc/freeradius/eap.conf including configuration file /etc/freeradius/sql.conf including configuration file /etc/freeradius/sql/mysql/dialup.conf including configuration file /etc/freeradius/policy.conf including files in directory /etc/freeradius/sites-enabled/ including configuration file /etc/freeradius/sites-enabled/default including configuration file /etc/freeradius/sites-enabled/inner-tunnel main { user = "freerad" group = "freerad" allow_core_dumps = no } including dictionary file /etc/freeradius/dictionary main { prefix = "/usr" localstatedir = "/var" logdir = "/var/log/freeradius" libdir = "/usr/lib/freeradius" radacctdir = "/var/log/freeradius/radacct" hostname_lookups = no max_request_time = 30 cleanup_delay = 5 max_requests = 1024 pidfile = "/var/run/freeradius/freeradius.pid" checkrad = "/usr/sbin/checkrad" debug_level = 0 proxy_requests = yes log { stripped_names = no auth = no auth_badpass = no auth_goodpass = no } security { max_attributes = 200 reject_delay = 1 status_server = yes } } radiusd: #### Loading Realms and Home Servers #### proxy server { retry_delay = 5 retry_count = 3 default_fallback = no dead_time = 120 wake_all_if_all_dead = no } home_server localhost { ipaddr = 127.0.0.1 port = 1812 type = "auth" secret = "testing123" response_window = 20 max_outstanding = 65536 require_message_authenticator = no zombie_period = 40 status_check = "status-server" ping_interval = 30 check_interval = 30 num_answers_to_alive = 3 num_pings_to_alive = 3 revive_interval = 120 status_check_timeout = 4 irt = 2 mrt = 16 mrc = 5 mrd = 30 } home_server_pool my_auth_failover { type = fail-over home_server = localhost } realm example.com { auth_pool = my_auth_failover } realm LOCAL { } radiusd: #### Loading Clients #### client localhost { ipaddr = 127.0.0.1 require_message_authenticator = no secret = "testing123" nastype = "other" } radiusd: #### Instantiating modules #### instantiate { Module: Linked to module rlm_exec Module: Instantiating exec exec { wait = no input_pairs = "request" shell_escape = yes } Module: Linked to module rlm_expr Module: Instantiating expr Module: Linked to module rlm_expiration Module: Instantiating expiration expiration { reply-message = "Password Has Expired " } Module: Linked to module rlm_logintime Module: Instantiating logintime logintime { reply-message = "You are calling outside your allowed timespan " minimum-timeout = 60 } } radiusd: #### Loading Virtual Servers #### server inner-tunnel { modules { Module: Checking authenticate {...} for more modules to load Module: Linked to module rlm_pap Module: Instantiating pap pap { encryption_scheme = "auto" auto_header = no } Module: Linked to module rlm_chap Module: Instantiating chap Module: Linked to module rlm_mschap Module: Instantiating mschap mschap { use_mppe = yes require_encryption = no require_strong = no with_ntdomain_hack = no } Module: Linked to module rlm_unix Module: Instantiating unix unix { radwtmp = "/var/log/freeradius/radwtmp" } Module: Linked to module rlm_eap Module: Instantiating eap eap { default_eap_type = "ttls" timer_expire = 60 ignore_unknown_eap_types = no cisco_accounting_username_bug = no max_sessions = 4096 } Module: Linked to sub-module rlm_eap_md5 Module: Instantiating eap-md5 Module: Linked to sub-module rlm_eap_leap Module: Instantiating eap-leap Module: Linked to sub-module rlm_eap_gtc Module: Instantiating eap-gtc gtc { challenge = "Password: " auth_type = "PAP" } Module: Linked to sub-module rlm_eap_tls Module: Instantiating eap-tls tls { rsa_key_exchange = no dh_key_exchange = yes rsa_key_length = 512 dh_key_length = 512 verify_depth = 0 pem_file_type = yes private_key_file = "/etc/freeradius/certs/server.key" certificate_file = "/etc/freeradius/certs/server.pem" CA_file = "/etc/freeradius/certs/ca.pem" private_key_password = "whatever" dh_file = "/etc/freeradius/certs/dh" random_file = "/etc/freeradius/certs/random" fragment_size = 1024 include_length = yes check_crl = no cipher_list = "DEFAULT" make_cert_command = "/etc/freeradius/certs/bootstrap" cache { enable = no lifetime = 24 max_entries = 255 } } Module: Linked to sub-module rlm_eap_ttls Module: Instantiating eap-ttls ttls { default_eap_type = "md5" copy_request_to_tunnel = no use_tunneled_reply = no virtual_server = "inner-tunnel" include_length = yes } Module: Linked to sub-module rlm_eap_peap Module: Instantiating eap-peap peap { default_eap_type = "mschapv2" copy_request_to_tunnel = no use_tunneled_reply = no proxy_tunneled_request_as_eap = yes virtual_server = "inner-tunnel" } Module: Linked to sub-module rlm_eap_mschapv2 Module: Instantiating eap-mschapv2 mschapv2 { with_ntdomain_hack = no } Module: Checking authorize {...} for more modules to load Module: Linked to module rlm_realm Module: Instantiating suffix realm suffix { format = "suffix" delimiter = "@" ignore_default = no ignore_null = no } Module: Linked to module rlm_files Module: Instantiating files files { usersfile = "/etc/freeradius/users" acctusersfile = "/etc/freeradius/acct_users" preproxy_usersfile = "/etc/freeradius/preproxy_users" compat = "no" } Module: Linked to module rlm_sql Module: Instantiating sql sql { driver = "rlm_sql_mysql" server = "localhost" port = "" login = "radius" password = "pxHP7KoX" radius_db = "radius" read_groups = yes sqltrace = no sqltracefile = "/var/log/freeradius/sqltrace.sql" readclients = yes deletestalesessions = yes num_sql_socks = 5 lifetime = 0 max_queries = 0 sql_user_name = "%{User-Name}" default_user_profile = "" nas_query = "SELECT id, nasname, shortname, type, secret FROM nas" authorize_check_query = "SELECT id, username, attribute, value, op FROM radcheck WHERE username = '%{SQL-User-Name}' ORDER BY id" authorize_reply_query = "SELECT id, username, attribute, value, op FROM radreply WHERE username = '%{SQL-User-Name}' ORDER BY id" authorize_group_check_query = "SELECT id, groupname, attribute, Value, op FROM radgroupcheck WHERE groupname = '%{Sql-Group}' ORDER BY id" authorize_group_reply_query = "SELECT id, groupname, attribute, value, op FROM radgroupreply WHERE groupname = '%{Sql-Group}' ORDER BY id" accounting_onoff_query = " UPDATE radacct SET acctstoptime = '%S', acctsessiontime = unix_timestamp('%S') - unix_timestamp(acctstarttime), acctterminatecause = '%{Acct-Terminate-Cause}', acctstopdelay = %{%{Acct-Delay-Time}:-0} WHERE acctstoptime IS NULL AND nasipaddress = '%{NAS-IP-Address}' AND acctstarttime <= '%S'" accounting_update_query = " UPDATE radacct SET framedipaddress = '%{Framed-IP-Address}', acctsessiontime = '%{Acct-Session-Time}', acctinputoctets = '%{%{Acct-Input-Gigawords}:-0}' << 32 | '%{%{Acct-Input-Octets}:-0}', acctoutputoctets = '%{%{Acct-Output-Gigawords}:-0}' << 32 | '%{%{Acct-Output-Octets}:-0}' WHERE acctsessionid = '%{Acct-Session-Id}' AND username = '%{SQL-User-Name}' AND nasipaddress = '%{NAS-IP-Address}'" accounting_update_query_alt = " INSERT INTO radacct (acctsessionid, acctuniqueid, username, realm, nasipaddress, nasportid, nasporttype, acctstarttime, acctsessiontime, acctauthentic, connectinfo_start, acctinputoctets, acctoutputoctets, calledstationid, callingstationid, servicetype, framedprotocol, framedipaddress, acctstartdelay, xascendsessionsvrkey) VALUES ('%{Acct-Session-Id}', '%{Acct-Unique-Session-Id}', '%{SQL-User-Name}', '%{Realm}', '%{NAS-IP-Address}', '%{NAS-Port}', '%{NAS-Port-Type}', DATE_SUB('%S', INTERVAL (%{%{Acct-Session-Time}:-0} + %{%{Acct-Delay-Time}:-0}) SECOND), '%{Acct-Session-Time}', '%{Acct-Authentic}', '', '%{%{Acct-Input-Gigawords}:-0}' << 32 | '%{%{Acct-Input-Octets}:-0}', '%{%{Acct-Output-Gigawords}:-0}' << 32 | '%{%{Acct-Output-Octets}:-0}', '%{Called-Station-Id}', '%{Calling-Station-Id}', '%{Service-Type}', '%{Framed-Protocol}', '%{Framed-IP-Address}', '0', '%{X-Ascend-Session-Svr-Key}')" accounting_start_query = " INSERT INTO radacct (acctsessionid, acctuniqueid, username, realm, nasipaddress, nasportid, nasporttype, acctstarttime, acctstoptime, acctsessiontime, acctauthentic, connectinfo_start, connectinfo_stop, acctinputoctets, acctoutputoctets, calledstationid, callingstationid, acctterminatecause, servicetype, framedprotocol, framedipaddress, acctstartdelay, acctstopdelay, xascendsessionsvrkey) VALUES ('%{Acct-Session-Id}', '%{Acct-Unique-Session-Id}', '%{SQL-User-Name}', '%{Realm}', '%{NAS-IP-Address}', '%{NAS-Port}', '%{NAS-Port-Type}', '%S', NULL, '0', '%{Acct-Authentic}', '%{Connect-Info}', '', '0', '0', '%{Called-Station-Id}', '%{Calling-Station-Id}', '', '%{Service-Type}', '%{Framed-Protocol}', '%{Framed-IP-Address}', '%{%{Acct-Delay-Time}:-0}', '0', '%{X-Ascend-Session-Svr-Key}')" accounting_start_query_alt = " UPDATE radacct SET acctstarttime = '%S', acctstartdelay = '%{%{Acct-Delay-Time}:-0}', connectinfo_start = '%{Connect-Info}' WHERE acctsessionid = '%{Acct-Session-Id}' AND username = '%{SQL-User-Name}' AND nasipaddress = '%{NAS-IP-Address}'" accounting_stop_query = " UPDATE radacct SET acctstoptime = '%S', acctsessiontime = '%{Acct-Session-Time}', acctinputoctets = '%{%{Acct-Input-Gigawords}:-0}' << 32 | '%{%{Acct-Input-Octets}:-0}', acctoutputoctets = '%{%{Acct-Output-Gigawords}:-0}' << 32 | '%{%{Acct-Output-Octets}:-0}', acctterminatecause = '%{Acct-Terminate-Cause}', acctstopdelay = '%{%{Acct-Delay-Time}:-0}', connectinfo_stop = '%{Connect-Info}' WHERE acctsessionid = '%{Acct-Session-Id}' AND username = '%{SQL-User-Name}' AND nasipaddress = '%{NAS-IP-Address}'" accounting_stop_query_alt = " INSERT INTO radacct (acctsessionid, acctuniqueid, username, realm, nasipaddress, nasportid, nasporttype, acctstarttime, acctstoptime, acctsessiontime, acctauthentic, connectinfo_start, connectinfo_stop, acctinputoctets, acctoutputoctets, calledstationid, callingstationid, acctterminatecause, servicetype, framedprotocol, framedipaddress, acctstartdelay, acctstopdelay) VALUES ('%{Acct-Session-Id}', '%{Acct-Unique-Session-Id}', '%{SQL-User-Name}', '%{Realm}', '%{NAS-IP-Address}', '%{NAS-Port}', '%{NAS-Port-Type}', DATE_SUB('%S', INTERVAL (%{%{Acct-Session-Time}:-0} + %{%{Acct-Delay-Time}:-0}) SECOND), '%S', '%{Acct-Session-Time}', '%{Acct-Authentic}', '', '%{Connect-Info}', '%{%{Acct-Input-Gigawords}:-0}' << 32 | '%{%{Acct-Input-Octets}:-0}', '%{%{Acct-Output-Gigawords}:-0}' << 32 | '%{%{Acct-Output-Octets}:-0}', '%{Called-Station-Id}', '%{Calling-Station-Id}', '%{Acct-Terminate-Cause}', '%{Service-Type}', '%{Framed-Protocol}', '%{Framed-IP-Address}', '0', '%{%{Acct-Delay-Time}:-0}')" group_membership_query = "SELECT groupname FROM radusergroup WHERE username = '%{SQL-User-Name}' ORDER BY priority" connect_failure_retry_delay = 60 simul_count_query = "" simul_verify_query = "SELECT radacctid, acctsessionid, username, nasipaddress, nasportid, framedipaddress, callingstationid, framedprotocol FROM radacct WHERE username = '%{SQL-User-Name}' AND acctstoptime IS NULL" postauth_query = "INSERT INTO radpostauth (username, pass, reply, authdate) VALUES ( '%{User-Name}', '%{%{User-Password}:-%{Chap-Password}}', '%{reply:Packet-Type}', '%S')" safe-characters = "@abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789.-_: /" } rlm_sql (sql): Driver rlm_sql_mysql (module rlm_sql_mysql) loaded and linked rlm_sql (sql): Attempting to connect to radius@localhost:/radius rlm_sql (sql): starting 0 rlm_sql (sql): Attempting to connect rlm_sql_mysql #0 rlm_sql_mysql: Starting connect to MySQL server for #0 rlm_sql (sql): Connected new DB handle, #0 rlm_sql (sql): starting 1 rlm_sql (sql): Attempting to connect rlm_sql_mysql #1 rlm_sql_mysql: Starting connect to MySQL server for #1 rlm_sql (sql): Connected new DB handle, #1 rlm_sql (sql): starting 2 rlm_sql (sql): Attempting to connect rlm_sql_mysql #2 rlm_sql_mysql: Starting connect to MySQL server for #2 rlm_sql (sql): Connected new DB handle, #2 rlm_sql (sql): starting 3 rlm_sql (sql): Attempting to connect rlm_sql_mysql #3 rlm_sql_mysql: Starting connect to MySQL server for #3 rlm_sql (sql): Connected new DB handle, #3 rlm_sql (sql): starting 4 rlm_sql (sql): Attempting to connect rlm_sql_mysql #4 rlm_sql_mysql: Starting connect to MySQL server for #4 rlm_sql (sql): Connected new DB handle, #4 rlm_sql (sql): Processing generate_sql_clients rlm_sql (sql) in generate_sql_clients: query is SELECT id, nasname, shortname, type, secret FROM nas rlm_sql (sql): Reserving sql socket id: 4 rlm_sql (sql): Read entry nasname=192.168.1.170,shortname=testap-test,secret=testing123 rlm_sql (sql): Adding client 192.168.1.170 (testap-test, server=<none>) to clients list rlm_sql (sql): Released sql socket id: 4 Module: Checking session {...} for more modules to load Module: Linked to module rlm_radutmp Module: Instantiating radutmp radutmp { filename = "/var/log/freeradius/radutmp" username = "%{User-Name}" case_sensitive = yes check_with_nas = yes perm = 384 callerid = yes } Module: Checking post-proxy {...} for more modules to load Module: Checking post-auth {...} for more modules to load Module: Linked to module rlm_attr_filter Module: Instantiating attr_filter.access_reject attr_filter attr_filter.access_reject { attrsfile = "/etc/freeradius/attrs.access_reject" key = "%{User-Name}" } } # modules } # server server { modules { Module: Checking authenticate {...} for more modules to load Module: Checking authorize {...} for more modules to load Module: Linked to module rlm_preprocess Module: Instantiating preprocess preprocess { huntgroups = "/etc/freeradius/huntgroups" hints = "/etc/freeradius/hints" with_ascend_hack = no ascend_channels_per_line = 23 with_ntdomain_hack = no with_specialix_jetstream_hack = no with_cisco_vsa_hack = no with_alvarion_vsa_hack = no } Module: Checking preacct {...} for more modules to load Module: Linked to module rlm_acct_unique Module: Instantiating acct_unique acct_unique { key = "User-Name, Acct-Session-Id, NAS-IP-Address, Client-IP-Address, NAS-Port" } Module: Checking accounting {...} for more modules to load Module: Linked to module rlm_detail Module: Instantiating detail detail { detailfile = "/var/log/freeradius/radacct/%{Client-IP-Address}/detail-%Y%m%d" header = "%t" detailperm = 384 dirperm = 493 locking = no log_packet_header = no } Module: Instantiating attr_filter.accounting_response attr_filter attr_filter.accounting_response { attrsfile = "/etc/freeradius/attrs.accounting_response" key = "%{User-Name}" } Module: Checking session {...} for more modules to load Module: Checking post-proxy {...} for more modules to load Module: Checking post-auth {...} for more modules to load } # modules } # server radiusd: #### Opening IP addresses and Ports #### listen { type = "auth" ipaddr = * port = 0 } listen { type = "acct" ipaddr = * port = 0 } Listening on authentication address * port 1812 Listening on accounting address * port 1813 Listening on proxy address * port 1814 Ready to process requests. rad_recv: Access-Request packet from host 192.168.1.170 port 3074, id=1, length=272 User-Name = "krijn" NAS-Identifier = "00-0b-6b-4f-80-65:testap" NAS-IP-Address = 192.168.1.170 NAS-Port = 5 NAS-Port-Id = "ath0" NAS-Port-Type = Wireless-802.11 Service-Type = Framed-User Framed-MTU = 1400 Called-Station-Id = "00-0B-6B-4F-80-65:testap" Calling-Station-Id = "00-0B-6B-D9-D0-14" Event-Timestamp = "Oct 5 2010 08:59:07 CEST" WISPr-Location-ID = "isocc=(null),cc=(null),ac=(null),network=(null)" WISPr-Location-Name = "(null),(null)" Connect-Info = "CONNECT 11Mbps 802.11b" EAP-Message = 0x0200000a016b72696a6e Message-Authenticator = 0xa74b44261469ee92ecf675d56836dabc +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "krijn", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 0 length 10 [eap] No EAP Start, assuming it's an on-going EAP conversation ++[eap] returns updated ++[unix] returns notfound ++[files] returns noop [sql] expand: %{User-Name} -> krijn [sql] sql_set_user escaped user --> 'krijn' rlm_sql (sql): Reserving sql socket id: 3 [sql] expand: SELECT id, username, attribute, value, op FROM radcheck WHERE username = '%{SQL-User-Name}' ORDER BY id -> SELECT id, username, attribute, value, op FROM radcheck WHERE username = 'krijn' ORDER BY id [sql] User found in radcheck table [sql] expand: SELECT id, username, attribute, value, op FROM radreply WHERE username = '%{SQL-User-Name}' ORDER BY id -> SELECT id, username, attribute, value, op FROM radreply WHERE username = 'krijn' ORDER BY id [sql] expand: SELECT groupname FROM radusergroup WHERE username = '%{SQL-User-Name}' ORDER BY priority -> SELECT groupname FROM radusergroup WHERE username = 'krijn' ORDER BY priority [sql] expand: SELECT id, groupname, attribute, Value, op FROM radgroupcheck WHERE groupname = '%{Sql-Group}' ORDER BY id -> SELECT id, groupname, attribute, Value, op FROM radgroupcheck WHERE groupname = '1' ORDER BY id [sql] User found in group 1 [sql] expand: SELECT id, groupname, attribute, value, op FROM radgroupreply WHERE groupname = '%{Sql-Group}' ORDER BY id -> SELECT id, groupname, attribute, value, op FROM radgroupreply WHERE groupname = '1' ORDER BY id rlm_sql (sql): Released sql socket id: 3 ++[sql] returns ok ++[expiration] returns noop ++[logintime] returns noop [pap] Found existing Auth-Type, not changing it. ++[pap] returns noop Found Auth-Type = EAP +- entering group authenticate {...} [eap] EAP Identity [eap] processing type tls [tls] Initiate [tls] Start returned 1 ++[eap] returns handled Sending Access-Challenge of id 1 to 192.168.1.170 port 3074 WISPr-Bandwidth-Max-Down = 1024000 WISPr-Bandwidth-Max-Up = 256000 Acct-Interim-Interval = 600 Idle-Timeout = 2628000 EAP-Message = 0x010100061520 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x3c19f5cd3c18e0363152d338edbf53e8 Finished request 0. Going to the next request Waking up in 4.9 seconds. rad_recv: Access-Request packet from host 192.168.1.170 port 3074, id=2, length=286 User-Name = "krijn" NAS-Identifier = "00-0b-6b-4f-80-65:testap" NAS-IP-Address = 192.168.1.170 NAS-Port = 5 NAS-Port-Id = "ath0" NAS-Port-Type = Wireless-802.11 Service-Type = Framed-User Framed-MTU = 1400 Called-Station-Id = "00-0B-6B-4F-80-65:testap" Calling-Station-Id = "00-0B-6B-D9-D0-14" Event-Timestamp = "Oct 5 2010 08:59:07 CEST" WISPr-Location-ID = "isocc=(null),cc=(null),ac=(null),network=(null)" WISPr-Location-Name = "(null),(null)" Connect-Info = "CONNECT 11Mbps 802.11b" EAP-Message = 0x020100060319 State = 0x3c19f5cd3c18e0363152d338edbf53e8 Message-Authenticator = 0xa37663f649567f230f75a8fb1cc7cb1b +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "krijn", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 1 length 6 [eap] No EAP Start, assuming it's an on-going EAP conversation ++[eap] returns updated ++[unix] returns notfound ++[files] returns noop [sql] expand: %{User-Name} -> krijn [sql] sql_set_user escaped user --> 'krijn' rlm_sql (sql): Reserving sql socket id: 2 [sql] expand: SELECT id, username, attribute, value, op FROM radcheck WHERE username = '%{SQL-User-Name}' ORDER BY id -> SELECT id, username, attribute, value, op FROM radcheck WHERE username = 'krijn' ORDER BY id [sql] User found in radcheck table [sql] expand: SELECT id, username, attribute, value, op FROM radreply WHERE username = '%{SQL-User-Name}' ORDER BY id -> SELECT id, username, attribute, value, op FROM radreply WHERE username = 'krijn' ORDER BY id [sql] expand: SELECT groupname FROM radusergroup WHERE username = '%{SQL-User-Name}' ORDER BY priority -> SELECT groupname FROM radusergroup WHERE username = 'krijn' ORDER BY priority [sql] expand: SELECT id, groupname, attribute, Value, op FROM radgroupcheck WHERE groupname = '%{Sql-Group}' ORDER BY id -> SELECT id, groupname, attribute, Value, op FROM radgroupcheck WHERE groupname = '1' ORDER BY id [sql] User found in group 1 [sql] expand: SELECT id, groupname, attribute, value, op FROM radgroupreply WHERE groupname = '%{Sql-Group}' ORDER BY id -> SELECT id, groupname, attribute, value, op FROM radgroupreply WHERE groupname = '1' ORDER BY id rlm_sql (sql): Released sql socket id: 2 ++[sql] returns ok ++[expiration] returns noop ++[logintime] returns noop [pap] Found existing Auth-Type, not changing it. ++[pap] returns noop Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP NAK [eap] EAP-NAK asked for EAP-Type/peap [eap] processing type tls [tls] Initiate [tls] Start returned 1 ++[eap] returns handled Sending Access-Challenge of id 2 to 192.168.1.170 port 3074 WISPr-Bandwidth-Max-Down = 1024000 WISPr-Bandwidth-Max-Up = 256000 Acct-Interim-Interval = 600 Idle-Timeout = 2628000 EAP-Message = 0x010200061920 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x3c19f5cd3d1bec363152d338edbf53e8 Finished request 1. Going to the next request Waking up in 4.9 seconds. rad_recv: Access-Request packet from host 192.168.1.170 port 3074, id=3, length=386 User-Name = "krijn" NAS-Identifier = "00-0b-6b-4f-80-65:testap" NAS-IP-Address = 192.168.1.170 NAS-Port = 5 NAS-Port-Id = "ath0" NAS-Port-Type = Wireless-802.11 Service-Type = Framed-User Framed-MTU = 1400 Called-Station-Id = "00-0B-6B-4F-80-65:testap" Calling-Station-Id = "00-0B-6B-D9-D0-14" Event-Timestamp = "Oct 5 2010 08:59:07 CEST" WISPr-Location-ID = "isocc=(null),cc=(null),ac=(null),network=(null)" WISPr-Location-Name = "(null),(null)" Connect-Info = "CONNECT 11Mbps 802.11b" EAP-Message = 0x0202006a1900160301005f0100005b03010000001340e29ad00b6989cd564d258938da96c8 39029d5a5d1c2d4d8619182500003400390038003500160013000a00330032002f0066000500 04006300620061001500120009006500640060001400110008000600030100 State = 0x3c19f5cd3d1bec363152d338edbf53e8 Message-Authenticator = 0x3efeb0cfcfbf6419b4dc2dc8792caa02 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "krijn", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 2 length 106 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] eaptls_verify returned 7 [peap] Done initial handshake [peap] (other): before/accept initialization [peap] TLS_accept: before/accept initialization [peap] <<< TLS 1.0 Handshake [length 005f], ClientHello [peap] TLS_accept: SSLv3 read client hello A [peap] >>> TLS 1.0 Handshake [length 002a], ServerHello [peap] TLS_accept: SSLv3 write server hello A [peap] >>> TLS 1.0 Handshake [length 01af], Certificate [peap] TLS_accept: SSLv3 write certificate A [peap] >>> TLS 1.0 Handshake [length 018d], ServerKeyExchange [peap] TLS_accept: SSLv3 write key exchange A [peap] >>> TLS 1.0 Handshake [length 0004], ServerHelloDone [peap] TLS_accept: SSLv3 write server done A [peap] TLS_accept: SSLv3 flush data [peap] TLS_accept: Need to read more data: SSLv3 read client certificate A In SSL Handshake Phase In SSL Accept mode [peap] eaptls_process returned 13 [peap] EAPTLS_HANDLED ++[eap] returns handled Sending Access-Challenge of id 3 to 192.168.1.170 port 3074 EAP-Message = 0x010303841900160301002a0200002603014caaccbc9c615b2f095fd11045adac321956ffcb 3f36352a2b6fd272306d35610000390016030101af0b0001ab0001a80001a5308201a1308201 0a020900fff668e689d331e6300d06092a864886f70d01010505003015311330110603550403 130a74657374736572766572301e170d3130313030343134303132335a170d32303130303131 34303132335a3015311330110603550403130a7465737473657276657230819f300d06092a86 4886f70d010101050003818d0030818902818100bf167df6f931627b07b69e4cc3dd25ae815a 4ae7c793c14abdf53a8a6caa06bf79fd93347e5b37b332827265 EAP-Message = 0x4842529d400d5dda7f8b3bbe950cfc113c7328263fb130ddf251f8faccfb58d4856c46faf7 9d7568ba233cf53022e910ab7cb77b62e8e508ee739db47cc844d5f00a6e95792dda8ed46008 52e5a8d3741304b3110203010001300d06092a864886f70d0101050500038181000c40ac1712 69e1329682dedffe00461c757886790d10da107d8f719c810f8244974859efdcbfa0a83645b9 2e069dd2b92ab5839786ad555893500fc46d61d3bd3519801fcabe048066189ea53131b6a1e9 f1c23e6bdf9b4dc97ccea591cbeb15460206c1b732c0fd1e2a00d6a1895569eb9d19cbd55530 dcea610bf14d8da233160301018d0c0001890080a4cc8a888c39 EAP-Message = 0xd932f9736364485a8a4f05da0076078f715322c76ef3051582dd449f484828a098c9eefd33 4501c12cde6e3471793ab92bdc3b39e765430532347d4a7d10fd58a56285e25bc1998ecf3fa3 a7b2b0f65f637e951315a3a0640fda0adbbfbd91663c79b34ca08989a3b3f62c0c49fdae0409 44c973a45a8c9557bb00010200800c9fb5f3617363c9ea77ecd84a286a29a623d3281f7b6e45 2d15d99e196204c9929f407c3dfeaab7690b20c34bad504ffbcf277caa82cb379bf1c28a5aa9 6c3f432201f5c715212e1bde165547d20fcf558af7581ed010669868defe48d88aa8bf889b96 835e0869be83b843810f65a1fe24a78594a884fd7b216f0e72bf EAP-Message = 0x3af9008011ed2ced9838a73dd729b91d2012cef0d25c348dbc945cedf586399077cf16c6ae f1204691f759daf8ba507d8405e573b3df86f886a118c0ba68e96b3b1ed6b24914ec333da4d0 3e93efff746a37b1bbfced477b0408b3f2bc568d90a1862f56fcb3719074c7c306f32e51423a 5edfee699c66c28df279bc4f94827b6c74a7a616030100040e000000 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x3c19f5cd3e1aec363152d338edbf53e8 Finished request 2. Going to the next request Waking up in 4.9 seconds. rad_recv: Access-Request packet from host 192.168.1.170 port 3074, id=4, length=484 User-Name = "krijn" NAS-Identifier = "00-0b-6b-4f-80-65:testap" NAS-IP-Address = 192.168.1.170 NAS-Port = 5 NAS-Port-Id = "ath0" NAS-Port-Type = Wireless-802.11 Service-Type = Framed-User Framed-MTU = 1400 Called-Station-Id = "00-0B-6B-4F-80-65:testap" Calling-Station-Id = "00-0B-6B-D9-D0-14" Event-Timestamp = "Oct 5 2010 08:59:07 CEST" WISPr-Location-ID = "isocc=(null),cc=(null),ac=(null),network=(null)" WISPr-Location-Name = "(null),(null)" Connect-Info = "CONNECT 11Mbps 802.11b" EAP-Message = 0x020300cc19001603010086100000820080318e590a5503e2ddf48b0e50d7f340dad2c95989 c507667565c59550b76aa16bf7d198ef91316fda591ee1b57c9f2c6eb882889ec7b9481cf0c9 a5ea2ea1be98a5d0ddc25b1edd561207be2d6e3b78d8b143d49dddfc47503475a9a7179f4795 923193c588e253b9785ca611a4fc2af00204363ea63cc48d2d810657c39a3468140301000101 1603010030dc3a4a1546859b9ddcf794712f0286d6d19c5a95567c6331add2bb3ca37f61cf6e ced76a13ae6a803d7a881238ec1d28 State = 0x3c19f5cd3e1aec363152d338edbf53e8 Message-Authenticator = 0xa3d18fa48823e8ccf2c5815d6a02d0f1 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "krijn", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 3 length 204 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] eaptls_verify returned 7 [peap] Done initial handshake [peap] <<< TLS 1.0 Handshake [length 0086], ClientKeyExchange [peap] TLS_accept: SSLv3 read client key exchange A [peap] <<< TLS 1.0 ChangeCipherSpec [length 0001] [peap] <<< TLS 1.0 Handshake [length 0010], Finished [peap] TLS_accept: SSLv3 read finished A [peap] >>> TLS 1.0 ChangeCipherSpec [length 0001] [peap] TLS_accept: SSLv3 write change cipher spec A [peap] >>> TLS 1.0 Handshake [length 0010], Finished [peap] TLS_accept: SSLv3 write finished A [peap] TLS_accept: SSLv3 flush data [peap] (other): SSL negotiation finished successfully SSL Connection Established [peap] eaptls_process returned 13 [peap] EAPTLS_HANDLED ++[eap] returns handled Sending Access-Challenge of id 4 to 192.168.1.170 port 3074 EAP-Message = 0x0104004119001403010001011603010030d2ff0895d7bd3dbfb00c502ec0f31537846179e0 7565c8723b4c6a88009d5441159e8c2b99c402cc37a5f0b64dc423c6 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x3c19f5cd3f1dec363152d338edbf53e8 Finished request 3. Going to the next request Waking up in 4.6 seconds. rad_recv: Access-Request packet from host 192.168.1.170 port 3074, id=5, length=286 User-Name = "krijn" NAS-Identifier = "00-0b-6b-4f-80-65:testap" NAS-IP-Address = 192.168.1.170 NAS-Port = 5 NAS-Port-Id = "ath0" NAS-Port-Type = Wireless-802.11 Service-Type = Framed-User Framed-MTU = 1400 Called-Station-Id = "00-0B-6B-4F-80-65:testap" Calling-Station-Id = "00-0B-6B-D9-D0-14" Event-Timestamp = "Oct 5 2010 08:59:07 CEST" WISPr-Location-ID = "isocc=(null),cc=(null),ac=(null),network=(null)" WISPr-Location-Name = "(null),(null)" Connect-Info = "CONNECT 11Mbps 802.11b" EAP-Message = 0x020400061900 State = 0x3c19f5cd3f1dec363152d338edbf53e8 Message-Authenticator = 0x9480a0249666b1883c1d8d21790ee596 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "krijn", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 4 length 6 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] Received TLS ACK [peap] ACK handshake is finished [peap] eaptls_verify returned 3 [peap] eaptls_process returned 3 [peap] EAPTLS_SUCCESS ++[eap] returns handled Sending Access-Challenge of id 5 to 192.168.1.170 port 3074 EAP-Message = 0x0105002b190017030100206eb3dd0c9c1e6680187097d6b6c76fc25af638d497b21010791e b62e4379b828 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x3c19f5cd381cec363152d338edbf53e8 Finished request 4. Going to the next request Waking up in 4.5 seconds. rad_recv: Access-Request packet from host 192.168.1.170 port 3074, id=6, length=360 User-Name = "krijn" NAS-Identifier = "00-0b-6b-4f-80-65:testap" NAS-IP-Address = 192.168.1.170 NAS-Port = 5 NAS-Port-Id = "ath0" NAS-Port-Type = Wireless-802.11 Service-Type = Framed-User Framed-MTU = 1400 Called-Station-Id = "00-0B-6B-4F-80-65:testap" Calling-Station-Id = "00-0B-6B-D9-D0-14" Event-Timestamp = "Oct 5 2010 08:59:07 CEST" WISPr-Location-ID = "isocc=(null),cc=(null),ac=(null),network=(null)" WISPr-Location-Name = "(null),(null)" Connect-Info = "CONNECT 11Mbps 802.11b" EAP-Message = 0x0205005019001703010020ee4ae6ada5a1487568b96cacf7a321d4d5b139175b480b1b6ebf 00b1c60b400c1703010020c3bf8ea38d3341efbc2c626b0ec6bfb8969d1eeda7cf512f1f4df3 a0c8e9f653 State = 0x3c19f5cd381cec363152d338edbf53e8 Message-Authenticator = 0x65107b1e03cbdd968ac88ef37c9ca744 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "krijn", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 5 length 80 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] eaptls_verify returned 7 [peap] Done initial handshake [peap] eaptls_process returned 7 [peap] EAPTLS_OK [peap] Session established. Decoding tunneled attributes. [peap] Identity - krijn [peap] Got tunneled request EAP-Message = 0x0205000a016b72696a6e server { PEAP: Got tunneled identity of krijn PEAP: Setting default EAP type for tunneled EAP session. PEAP: Setting User-Name to krijn Sending tunneled request EAP-Message = 0x0205000a016b72696a6e FreeRADIUS-Proxied-To = 127.0.0.1 User-Name = "krijn" server inner-tunnel { +- entering group authorize {...} ++[chap] returns noop ++[mschap] returns noop ++[unix] returns notfound [suffix] No '@' in User-Name = "krijn", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop ++[control] returns noop [eap] EAP packet type response id 5 length 10 [eap] No EAP Start, assuming it's an on-going EAP conversation ++[eap] returns updated ++[files] returns noop [sql] expand: %{User-Name} -> krijn [sql] sql_set_user escaped user --> 'krijn' rlm_sql (sql): Reserving sql socket id: 1 [sql] expand: SELECT id, username, attribute, value, op FROM radcheck WHERE username = '%{SQL-User-Name}' ORDER BY id -> SELECT id, username, attribute, value, op FROM radcheck WHERE username = 'krijn' ORDER BY id [sql] expand: SELECT groupname FROM radusergroup WHERE username = '%{SQL-User-Name}' ORDER BY priority -> SELECT groupname FROM radusergroup WHERE username = 'krijn' ORDER BY priority [sql] expand: SELECT id, groupname, attribute, Value, op FROM radgroupcheck WHERE groupname = '%{Sql-Group}' ORDER BY id -> SELECT id, groupname, attribute, Value, op FROM radgroupcheck WHERE groupname = '1' ORDER BY id [sql] User found in group 1 [sql] expand: SELECT id, groupname, attribute, value, op FROM radgroupreply WHERE groupname = '%{Sql-Group}' ORDER BY id -> SELECT id, groupname, attribute, value, op FROM radgroupreply WHERE groupname = '1' ORDER BY id rlm_sql (sql): Released sql socket id: 1 ++[sql] returns ok ++[expiration] returns noop ++[logintime] returns noop ++[pap] returns noop Found Auth-Type = EAP +- entering group authenticate {...} [eap] EAP Identity [eap] processing type mschapv2 rlm_eap_mschapv2: Issuing Challenge ++[eap] returns handled } # server inner-tunnel [peap] Got tunneled reply code 11 WISPr-Bandwidth-Max-Down = 1024000 WISPr-Bandwidth-Max-Up = 256000 Acct-Interim-Interval = 600 Idle-Timeout = 2628000 EAP-Message = 0x0106001f1a0106001a104752aad57bdcf603b76fc7d381e3cbac6b72696a6e Message-Authenticator = 0x00000000000000000000000000000000 State = 0x10b696e910b08c0331cee5911baf4ebf [peap] Got tunneled reply RADIUS code 11 WISPr-Bandwidth-Max-Down = 1024000 WISPr-Bandwidth-Max-Up = 256000 Acct-Interim-Interval = 600 Idle-Timeout = 2628000 EAP-Message = 0x0106001f1a0106001a104752aad57bdcf603b76fc7d381e3cbac6b72696a6e Message-Authenticator = 0x00000000000000000000000000000000 State = 0x10b696e910b08c0331cee5911baf4ebf [peap] Got tunneled Access-Challenge ++[eap] returns handled Sending Access-Challenge of id 6 to 192.168.1.170 port 3074 EAP-Message = 0x0106003b19001703010030195145a7f72a64ee47341aebba21d21b357960da36d402cd5468 9637b0e5f0902010c3a810c109a03ae6ec2ac0ae1e48 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x3c19f5cd391fec363152d338edbf53e8 Finished request 5. Going to the next request Waking up in 4.5 seconds. rad_recv: Access-Request packet from host 192.168.1.170 port 3074, id=7, length=424 User-Name = "krijn" NAS-Identifier = "00-0b-6b-4f-80-65:testap" NAS-IP-Address = 192.168.1.170 NAS-Port = 5 NAS-Port-Id = "ath0" NAS-Port-Type = Wireless-802.11 Service-Type = Framed-User Framed-MTU = 1400 Called-Station-Id = "00-0B-6B-4F-80-65:testap" Calling-Station-Id = "00-0B-6B-D9-D0-14" Event-Timestamp = "Oct 5 2010 08:59:07 CEST" WISPr-Location-ID = "isocc=(null),cc=(null),ac=(null),network=(null)" WISPr-Location-Name = "(null),(null)" Connect-Info = "CONNECT 11Mbps 802.11b" EAP-Message = 0x0206009019001703010020ea062db644dea720958cbdc60e4c7115b480effb316048421dce 1216cbad9eb11703010060d1be7119d5dd8ad98bd310ab62689a8445e3ea4cc69c9224227b98 14f986b73ea3143a2a1d4b33663e79cec39119261fda39294f2afb89c5c79bc1c03999f19a25 0d7dd9e9da3ddab2774756f0d7e4feac639d40ae700bd31d00a9dbe88736ca State = 0x3c19f5cd391fec363152d338edbf53e8 Message-Authenticator = 0x263cb5ad490289263be856060f09a796 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "krijn", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 6 length 144 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] eaptls_verify returned 7 [peap] Done initial handshake [peap] eaptls_process returned 7 [peap] EAPTLS_OK [peap] Session established. Decoding tunneled attributes. [peap] EAP type mschapv2 [peap] Got tunneled request EAP-Message = 0x020600401a0206003b311cbe232ecce24ed01afc751b15d832940000000000000000b346e2 afc1fb55e292226807a2f6b6219fb5adef860b91d6006b72696a6e server { PEAP: Setting User-Name to krijn Sending tunneled request EAP-Message = 0x020600401a0206003b311cbe232ecce24ed01afc751b15d832940000000000000000b346e2 afc1fb55e292226807a2f6b6219fb5adef860b91d6006b72696a6e FreeRADIUS-Proxied-To = 127.0.0.1 User-Name = "krijn" State = 0x10b696e910b08c0331cee5911baf4ebf server inner-tunnel { +- entering group authorize {...} ++[chap] returns noop ++[mschap] returns noop ++[unix] returns notfound [suffix] No '@' in User-Name = "krijn", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop ++[control] returns noop [eap] EAP packet type response id 6 length 64 [eap] No EAP Start, assuming it's an on-going EAP conversation ++[eap] returns updated ++[files] returns noop [sql] expand: %{User-Name} -> krijn [sql] sql_set_user escaped user --> 'krijn' rlm_sql (sql): Reserving sql socket id: 0 [sql] expand: SELECT id, username, attribute, value, op FROM radcheck WHERE username = '%{SQL-User-Name}' ORDER BY id -> SELECT id, username, attribute, value, op FROM radcheck WHERE username = 'krijn' ORDER BY id [sql] expand: SELECT groupname FROM radusergroup WHERE username = '%{SQL-User-Name}' ORDER BY priority -> SELECT groupname FROM radusergroup WHERE username = 'krijn' ORDER BY priority [sql] expand: SELECT id, groupname, attribute, Value, op FROM radgroupcheck WHERE groupname = '%{Sql-Group}' ORDER BY id -> SELECT id, groupname, attribute, Value, op FROM radgroupcheck WHERE groupname = '1' ORDER BY id [sql] User found in group 1 [sql] expand: SELECT id, groupname, attribute, value, op FROM radgroupreply WHERE groupname = '%{Sql-Group}' ORDER BY id -> SELECT id, groupname, attribute, value, op FROM radgroupreply WHERE groupname = '1' ORDER BY id rlm_sql (sql): Released sql socket id: 0 ++[sql] returns ok ++[expiration] returns noop ++[logintime] returns noop ++[pap] returns noop Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/mschapv2 [eap] processing type mschapv2 [mschapv2] +- entering group MS-CHAP {...} [mschap] No Cleartext-Password configured. Cannot create LM-Password. [mschap] No Cleartext-Password configured. Cannot create NT-Password. [mschap] Told to do MS-CHAPv2 for krijn with NT-Password [mschap] FAILED: No NT/LM-Password. Cannot perform authentication. [mschap] FAILED: MS-CHAP2-Response is incorrect ++[mschap] returns reject [eap] Freeing handler ++[eap] returns reject Failed to authenticate the user. } # server inner-tunnel [peap] Got tunneled reply code 3 WISPr-Bandwidth-Max-Down = 1024000 WISPr-Bandwidth-Max-Up = 256000 Acct-Interim-Interval = 600 Idle-Timeout = 2628000 MS-CHAP-Error = "\006E=691 R=1" EAP-Message = 0x04060004 Message-Authenticator = 0x00000000000000000000000000000000 [peap] Got tunneled reply RADIUS code 3 WISPr-Bandwidth-Max-Down = 1024000 WISPr-Bandwidth-Max-Up = 256000 Acct-Interim-Interval = 600 Idle-Timeout = 2628000 MS-CHAP-Error = "\006E=691 R=1" EAP-Message = 0x04060004 Message-Authenticator = 0x00000000000000000000000000000000 [peap] Tunneled authentication was rejected. [peap] FAILURE ++[eap] returns handled Sending Access-Challenge of id 7 to 192.168.1.170 port 3074 EAP-Message = 0x0107002b190017030100205e533de7969e5baa6274637054e3f62cff457c0764a24e44a460 6e0336bca402 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x3c19f5cd3a1eec363152d338edbf53e8 Finished request 6. Going to the next request Waking up in 4.5 seconds. rad_recv: Access-Request packet from host 192.168.1.170 port 3074, id=8, length=360 User-Name = "krijn" NAS-Identifier = "00-0b-6b-4f-80-65:testap" NAS-IP-Address = 192.168.1.170 NAS-Port = 5 NAS-Port-Id = "ath0" NAS-Port-Type = Wireless-802.11 Service-Type = Framed-User Framed-MTU = 1400 Called-Station-Id = "00-0B-6B-4F-80-65:testap" Calling-Station-Id = "00-0B-6B-D9-D0-14" Event-Timestamp = "Oct 5 2010 08:59:07 CEST" WISPr-Location-ID = "isocc=(null),cc=(null),ac=(null),network=(null)" WISPr-Location-Name = "(null),(null)" Connect-Info = "CONNECT 11Mbps 802.11b" EAP-Message = 0x0207005019001703010020ce731a7886af7bb4012bb7ff88b77637f2cef3aa2c726aff851f 2203e2a2237d1703010020b4bbb54590801f14f26b8e1f5a3add5038eacf4c5cb528b3a7c2b4 eef7f48e3f State = 0x3c19f5cd3a1eec363152d338edbf53e8 Message-Authenticator = 0xd90d51b254d2b36a1271fb2c22a94c03 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "krijn", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 7 length 80 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] eaptls_verify returned 7 [peap] Done initial handshake [peap] eaptls_process returned 7 [peap] EAPTLS_OK [peap] Session established. Decoding tunneled attributes. [peap] Received EAP-TLV response. [peap] Had sent TLV failure. User was rejected earlier in this session. [eap] Handler failed in EAP/peap [eap] Failed in EAP select ++[eap] returns invalid Failed to authenticate the user. Using Post-Auth-Type Reject +- entering group REJECT {...} [attr_filter.access_reject] expand: %{User-Name} -> krijn attr_filter: Matched entry DEFAULT at line 11 ++[attr_filter.access_reject] returns updated Delaying reject of request 7 for 1 seconds Going to the next request Waking up in 0.9 seconds. Sending delayed reject for request 7 Sending Access-Reject of id 8 to 192.168.1.170 port 3074 EAP-Message = 0x04070004 Message-Authenticator = 0x00000000000000000000000000000000 Waking up in 3.5 seconds. Cleaning up request 0 ID 1 with timestamp +31 Cleaning up request 1 ID 2 with timestamp +31 Cleaning up request 2 ID 3 with timestamp +31 Waking up in 0.3 seconds. Cleaning up request 3 ID 4 with timestamp +32 Cleaning up request 4 ID 5 with timestamp +32 Cleaning up request 5 ID 6 with timestamp +32 Cleaning up request 6 ID 7 with timestamp +32 Waking up in 1.0 seconds. Cleaning up request 7 ID 8 with timestamp +32 Ready to process requests. ^C root@testserver:/etc/freeradius/sites-enabled# Kind regards,   Krijn Tanis WiMood -----Oorspronkelijk bericht----- Van: Tim Sylvester [mailto:tim.sylvester.at.network.radius@gmail.com] Namens Tim Sylvester Verzonden: maandag 4 oktober 2010 20:51 Aan: 'Krijn Tanis | WiMood'; 'FreeRadius users mailing list' Onderwerp: RE: Check multiple attributes for one user

I ran Freeradius in debug mode already to check this:

Send the rest of the debug out so that we can see why the request was rejected. Tim

rad_recv: Access-Request packet from host 192.168.1.170 port 3098, id=201, length=286 User-Name = "krijn" NAS-Identifier = "00-0b-6b-4f-80-65:isiline" NAS-IP-Address = 192.168.1.170 NAS-Port = 5 NAS-Port-Id = "ath0" NAS-Port-Type = Wireless-802.11 Service-Type = Framed-User Framed-MTU = 1400 Called-Station-Id = "00-0B-6B-4F-80-65:isiline" Calling-Station-Id = "00-0B-6B-D9-D0-14" Event-Timestamp = "Oct 4 2010 19:10:41 CEST" WISPr-Location-ID = "isocc=(null),cc=(null),ac=(null),network=(null)" WISPr-Location-Name = "(null),(null)" Connect-Info = "CONNECT 11Mbps 802.11b" EAP-Message = 0x020100060319 State = 0x697a4088697b55320faa946fa7f606af Message-Authenticator = 0x73ade7409a1c7def5027792de162bd0b

Met vriendelijke groet/Kind regards,

Krijn Tanis WiMood Kerkstraat 8/10 3252 AX  Goedereede

Tel.: +31 (0) 187 82 0204 Fax: +31 (0) 187 49 1596 Mob.: +31 (0) 6 10923259 Mail: info@wimood.nl Web: http://www.wimood.nl

-----Oorspronkelijk bericht----- Van: freeradius-users-bounces+krijntanis=wimood.nl@lists.freeradius.org [mailto:freeradius-users- bounces+krijntanis=wimood.nl@lists.freeradius.org] Namens Tim Sylvester Verzonden: maandag 4 oktober 2010 20:16 Aan: 'FreeRadius users mailing list' Onderwerp: RE: Check multiple attributes for one user

Run the server in debug mode (radiusd -X) and check the attributes sent by the NAS. The NAS may not be sending the Calling-Station-Id or it may be in a different format. Either way, the debug output is going to give you more information.

Tim

...

| 1 | krijn | Calling-Station-Id | 00-0B-6B-D9-D0-14| == | | 2 | krijn | Cleartext-Password | test123 | := |

But this doesnt work, the user is rejected. Can somebody point me into the right direction?

Kind regards,

Krijn Tanis WiMood

- List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html

...

| id | UserName | Attribute | Value | Op | +----+----------------+--------------------+------------------+------

...

-----Original Message----- From: freeradius-users- bounces+tim.sylvester=networkradius.com@lists.freeradius.org [mailto:freeradius-users- bounces+tim.sylvester=networkradius.com@lists.freeradius.org] On bounces+Behalf Of Krijn Tanis | WiMood Sent: Monday, October 04, 2010 10:59 AM To: freeradius-users@lists.freeradius.org Subject: Check multiple attributes for one user

Hello all,

For a project I am working on 802.1x WPA-EAP authentication and for this I use a Freeradius server. This part of authentication works perfect.

Now I also want to check the Calling-Station-Id for the user, in this case it is MAC address of the wireless client. I want this because I want to allow the user to connect only from one MAC address (else user is able to use a other device that is not in our control, I want to prevent this. So I want to check the Password and Calling-Station-Id in one and the same Access Request. If both match an Access-Accept is sent, in all other cases (when password or Calling-Station-Id do not match for the user) an Access-Reject.

I tried to do this:

+----+----------------+--------------------+------------------+------

Hi, I only enabled SQL in inner-tunnel section authorize. It is not possible to enable it in authenticate, I get error: /etc/freeradius/sites-enabled/inner-tunnel[200]: "SQL" modules aren't allowed in 'authenticate' sections -- they have no such method Kind regards,   Krijn Tanis WiMood -----Oorspronkelijk bericht----- Van: freeradius-users-bounces+krijntanis=wimood.nl@lists.freeradius.org [mailto:freeradius-users-bounces+krijntanis=wimood.nl@lists.freeradius.org] Namens Alan Buxey Verzonden: dinsdag 5 oktober 2010 10:08 Aan: FreeRadius users mailing list Onderwerp: Re: Check multiple attributes for one user hi, you dont have any authenticationsuitable in the inner-tunnel ? perhaps ensure that sql is called in there? alan - List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html

Hello,

okay....well, inner-tunnel EAP section doesnt have a Cleartext-Password for your user - are your authorize queries okay in dialup.conf? What do you mean exactly. I didn't change anything yet in Radius config besides enabling EAP-TTLS and SQL.

Met vriendelijke groet/Kind regards,   Krijn Tanis WiMood -----Oorspronkelijk bericht----- Van: freeradius-users-bounces+krijntanis=wimood.nl@lists.freeradius.org [mailto:freeradius-users-bounces+krijntanis=wimood.nl@lists.freeradius.org] Namens Alan Buxey Verzonden: dinsdag 5 oktober 2010 12:07 Aan: FreeRadius users mailing list Onderwerp: Re: Check multiple attributes for one user Hi,

I only enabled SQL in inner-tunnel section authorize. It is not possible to enable it in authenticate, I get error:

oops. yes. silly me. you cannot authenticate because its a query not challenge method. okay....well, inner-tunnel EAP section doesnt have a Cleartext-Password for your user - are your authorize queries okay in dialup.conf? alan - List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html