If u really want 2 knw the issue, undo the changes one by one until it breaks again. ----- Original Message ----- From: freeradius-users-bounces+ggatten=waddell.com@lists.freeradius.org <freeradius-users-bounces+ggatten=waddell.com@lists.freeradius.org> To: FreeRadius users mailing list <freeradius-users@lists.freeradius.org> Sent: Wed Mar 24 04:56:19 2010 Subject: Re: Freeradius says it is listening on port 1812, but isn't Hi, I believe the problem is now resolved The only things I changed was that my hosts file was wrong, the IP for the servers FQDN was incorrect but I'm not sure this is what it was I also turned off ip forwarding with sysctl -w net.inet.ip.forwarding=0 Even though natd, and the firewall have been disabled. must be a weird OSX thing Sorry for wasting your time guys and thanks for the help Regards, Matt Harlum On 24/03/2010, at 8:27 PM, Matt Harlum wrote:
On 24/03/2010, at 8:21 PM, Fajar A. Nugraha wrote:
On Wed, Mar 24, 2010 at 3:51 PM, Matt Harlum <matt@cactuar.net> wrote:
Hi,
I'm running Freeradius 2.1.6 on MacOSX 10.5.7 on a Dual-G4 867Mhz PowerMac
Since march last year I've had 2.1.6 installed however it's been switched off for the last few months. Recently I powered it back on and have run system updates etc and got to the point I am now
When I launch FreeRadius it says it is listening on *:1812 for auth however my AP is unable to connect,
"unable to connect" is the result. Many things can cause it, from incorrent radius IP/secret settings on AP to firewalls blocking packets.
Checked both which are correct, no firewalls enabled
and trying telnet on port 1812 results in "Connection Refused"
you can't test UDP with telnet. Try the included radtest and radclient
Ahh ok, I'll give those a try
I've tried reverting the configuration to default but it hasn't worked. running radiusd -x does not throw any errors
does it print incoming packets and process it? does tcpdump (or whatever packet capture tools you have) shows incoming packets?
It doesn't show anything when connection attempts are made, I'll let you know how I go with netcat and the radtest tools Thanks
-- Fajar - List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
- List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
- List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
After my previous email I've successfully re-installed my custom config and am able to auth my clients again Regards, Matt Harlum On 25/03/2010, at 12:11 AM, Gary Gatten wrote:
If u really want 2 knw the issue, undo the changes one by one until it breaks again.
----- Original Message ----- From: freeradius-users-bounces+ggatten=waddell.com@lists.freeradius.org <freeradius-users-bounces+ggatten=waddell.com@lists.freeradius.org> To: FreeRadius users mailing list <freeradius-users@lists.freeradius.org> Sent: Wed Mar 24 04:56:19 2010 Subject: Re: Freeradius says it is listening on port 1812, but isn't
Hi,
I believe the problem is now resolved
The only things I changed was that my hosts file was wrong, the IP for the servers FQDN was incorrect but I'm not sure this is what it was I also turned off ip forwarding with sysctl -w net.inet.ip.forwarding=0 Even though natd, and the firewall have been disabled. must be a weird OSX thing
Sorry for wasting your time guys and thanks for the help
Regards, Matt Harlum
On 24/03/2010, at 8:27 PM, Matt Harlum wrote:
On 24/03/2010, at 8:21 PM, Fajar A. Nugraha wrote:
On Wed, Mar 24, 2010 at 3:51 PM, Matt Harlum <matt@cactuar.net> wrote:
Hi,
I'm running Freeradius 2.1.6 on MacOSX 10.5.7 on a Dual-G4 867Mhz PowerMac
Since march last year I've had 2.1.6 installed however it's been switched off for the last few months. Recently I powered it back on and have run system updates etc and got to the point I am now
When I launch FreeRadius it says it is listening on *:1812 for auth however my AP is unable to connect,
"unable to connect" is the result. Many things can cause it, from incorrent radius IP/secret settings on AP to firewalls blocking packets.
Checked both which are correct, no firewalls enabled
and trying telnet on port 1812 results in "Connection Refused"
you can't test UDP with telnet. Try the included radtest and radclient
Ahh ok, I'll give those a try
I've tried reverting the configuration to default but it hasn't worked. running radiusd -x does not throw any errors
does it print incoming packets and process it? does tcpdump (or whatever packet capture tools you have) shows incoming packets?
It doesn't show anything when connection attempts are made, I'll let you know how I go with netcat and the radtest tools Thanks
-- Fajar - List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
- List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
- List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
- List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
Hi, I am using 2.1.3 freeradius server and found memory leak. I use ttls+mschapv2 for authentication. After each authentication, the memory usage increases. Is there a patch fix for this? Thanks, Gina Zhang
participants (3)
-
Gary Gatten -
Matt Harlum -
Zhang, Ge (Gina)