Re: [Help] - How To configure Radius timeout / count retries
Out of topic : All, btw how can i make sure that when i reply in this mailing list it appears after the previous post ? I dont receieve any of your reply in my email and i have to go to the archive list to reply this. Thanks -- Best Regards, Danny
On 1 Mar 2013, at 00:20, Danny Kurniawan <danny.kurniawan@fairchildsemi.com> wrote:
Out of topic : All, btw how can i make sure that when i reply in this mailing list it appears after the previous post ? I dont receieve any of your reply in my email and i have to go to the archive list to reply this.
I'm not sure what you're asking...
No worries, i receive this mailing list on my email now.. OK, so i also understand that we can only configure that from the AP side. But unfortunately we cant find that in the Meraki AP ... let me check with our vendor on it. Thanks Danny On Fri, Mar 1, 2013 at 2:26 PM, Arran Cudbard-Bell < a.cudbardb@freeradius.org> wrote:
On 1 Mar 2013, at 00:20, Danny Kurniawan < danny.kurniawan@fairchildsemi.com> wrote:
Out of topic : All, btw how can i make sure that when i reply in this mailing list it appears after the previous post ? I dont receieve any of your reply in my email and i have to go to the archive list to reply this.
I'm not sure what you're asking... - List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
-- Best Regards, Danny
Arran,
* Let say for example in our Wireless AP (access point) we can put 2 Radius server in sequence, radiusA and radiusB. I know the AP will eventually look at the 1st server, and if its not available (let say server is down) then it will go to the 2nd radius server (I only assume this). *>* *>* So is there any way in Radius conf we can set the retries or timeout, so for example after failed for 2 times (no matter what is the error is) it will goes to the other radius server? * You're asking whether you can configure FreeRADIUS to inform the access point that it should fail over to another server server after a given number of timeouts/retries?
Or are you talking about failing over between upstream proxy servers? -Arran "Or are you talking about failing over between upstream proxy servers?" Does this mean a setup of Radius load balancing? I mean a few Radius server that used by the same AP ? So from AP point of view i just need to point to the "master" Ip address of the first radius server? Thanks Danny On Fri, Mar 1, 2013 at 3:27 PM, Danny Kurniawan < danny.kurniawan@fairchildsemi.com> wrote:
No worries, i receive this mailing list on my email now..
OK, so i also understand that we can only configure that from the AP side. But unfortunately we cant find that in the Meraki AP ... let me check with our vendor on it.
Thanks Danny
On Fri, Mar 1, 2013 at 2:26 PM, Arran Cudbard-Bell < a.cudbardb@freeradius.org> wrote:
On 1 Mar 2013, at 00:20, Danny Kurniawan < danny.kurniawan@fairchildsemi.com> wrote:
Out of topic : All, btw how can i make sure that when i reply in this mailing list it appears after the previous post ? I dont receieve any of your reply in my email and i have to go to the archive list to reply this.
I'm not sure what you're asking... - List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
-- Best Regards, Danny
-- Best Regards, Danny
"Or are you talking about failing over between upstream proxy servers?"
Does this mean a setup of Radius load balancing? I mean a few Radius server that used by the same AP ? So from AP point of view i just need to point to the "master" Ip address of the first radius server?
No. That's talking about when you use FreeRADIUS to forward packets onto another RADIUS server. FreeRADIUS cannot tell the Access Point about alternative RADIUS servers in the same cluster. It's not supported by the protocol. You need to configure them manually on each Access Point. If you want redundancy try using something like VRRP or Anycast. -Arran
Noted, thanks in advance. -Danny On Fri, Mar 1, 2013 at 11:04 PM, Arran Cudbard-Bell < a.cudbardb@freeradius.org> wrote:
"Or are you talking about failing over between upstream proxy servers?"
Does this mean a setup of Radius load balancing? I mean a few Radius
server that used by the same AP ? So from AP point of view i just need to point to the "master" Ip address of the first radius server?
No. That's talking about when you use FreeRADIUS to forward packets onto another RADIUS server.
FreeRADIUS cannot tell the Access Point about alternative RADIUS servers in the same cluster. It's not supported by the protocol.
You need to configure them manually on each Access Point.
If you want redundancy try using something like VRRP or Anycast.
-Arran
- List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
-- Best Regards, Danny
participants (2)
-
Arran Cudbard-Bell -
Danny Kurniawan