Hi guys, New to Freeradius. I installed freeradius in a virtualbox but cant get it work. This is the error that I get. rad_recv: Access-Request packet from host 127.0.0.1 port 52378, id=160, length=119 User-Name = "test-01" User-Password = "test-01" NAS-IP-Address = 127.0.1.1 NAS-Port = 1812 Message-Authenticator = 0xb4f32db02020dde2dea54abf00aad93e State = 0x1924712819bb75814c2d329074168479 EAP-Message = 0x029f00160410804938cd9f788564d605731c54d4ceaf # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop ++[digest] returns noop [suffix] No '@' in User-Name = "test-01", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 159 length 22 [eap] No EAP Start, assuming it's an on-going EAP conversation ++[eap] returns updated ++[files] returns noop ++[expiration] returns noop ++[logintime] returns noop [pap] WARNING! No "known good" password found for the user. Authentication may fail because of this. ++[pap] returns noop Found Auth-Type = EAP # Executing group from file /usr/local/etc/raddb/sites-enabled/default +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/md5 [eap] processing type md5 rlm_eap_md5: Cleartext-Password is required for EAP-MD5 authentication [eap] Handler failed in EAP/md5 [eap] Failed in EAP select ++[eap] returns invalid Failed to authenticate the user. Using Post-Auth-Type Reject # Executing group from file /usr/local/etc/raddb/sites-enabled/default +- entering group REJECT {...} [attr_filter.access_reject] expand: %{User-Name} -> test-01 attr_filter: Matched entry DEFAULT at line 11 ++[attr_filter.access_reject] returns updated Delaying reject of request 5 for 1 seconds Going to the next request Waking up in 0.9 seconds. Sending delayed reject for request 5 Sending Access-Reject of id 160 to 127.0.0.1 port 52378 EAP-Message = 0x049f0004 Message-Authenticator = 0x00000000000000000000000000000000 Waking up in 3.9 seconds. Cleaning up request 4 ID 159 with timestamp +5907 Waking up in 0.9 seconds. Cleaning up request 5 ID 160 with timestamp +5907 Ready to process requests. rad_recv: Access-Request packet from host 127.0.0.1 port 37217, id=174, length=91 User-Name = "test-01" User-Password = "test-01" NAS-IP-Address = 127.0.1.1 NAS-Port = 1812 Message-Authenticator = 0x3731176813fa2d963f45aad0433d91ce EAP-Message = 0x02ad000c01746573742d3031 # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop ++[digest] returns noop [suffix] No '@' in User-Name = "test-01", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 173 length 12 [eap] No EAP Start, assuming it's an on-going EAP conversation ++[eap] returns updated ++[files] returns noop ++[expiration] returns noop ++[logintime] returns noop [pap] WARNING! No "known good" password found for the user. Authentication may fail because of this. ++[pap] returns noop Found Auth-Type = EAP # Executing group from file /usr/local/etc/raddb/sites-enabled/default +- entering group authenticate {...} [eap] EAP Identity [eap] processing type md5 rlm_eap_md5: Issuing Challenge ++[eap] returns handled Sending Access-Challenge of id 174 to 127.0.0.1 port 37217 EAP-Message = 0x01ae00160410dd3b9e060bc20ab6c7618dabcbaba135 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x254299cc25ec9d2a127daea22ca93a94 Finished request 6. Going to the next request Waking up in 4.9 seconds. rad_recv: Access-Request packet from host 127.0.0.1 port 37217, id=175, length=119 User-Name = "test-01" User-Password = "test-01" NAS-IP-Address = 127.0.1.1 NAS-Port = 1812 Message-Authenticator = 0x74c8493a76c0fd7a58208e5ea899acfe State = 0x254299cc25ec9d2a127daea22ca93a94 EAP-Message = 0x02ae0016041005754627c66e7e1f2dd289bddf3faede # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop ++[digest] returns noop [suffix] No '@' in User-Name = "test-01", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 174 length 22 [eap] No EAP Start, assuming it's an on-going EAP conversation ++[eap] returns updated ++[files] returns noop ++[expiration] returns noop ++[logintime] returns noop [pap] WARNING! No "known good" password found for the user. Authentication may fail because of this. ++[pap] returns noop Found Auth-Type = EAP # Executing group from file /usr/local/etc/raddb/sites-enabled/default +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/md5 [eap] processing type md5 rlm_eap_md5: Cleartext-Password is required for EAP-MD5 authentication [eap] Handler failed in EAP/md5 [eap] Failed in EAP select ++[eap] returns invalid Failed to authenticate the user. Using Post-Auth-Type Reject # Executing group from file /usr/local/etc/raddb/sites-enabled/default +- entering group REJECT {...} [attr_filter.access_reject] expand: %{User-Name} -> test-01 attr_filter: Matched entry DEFAULT at line 11 ++[attr_filter.access_reject] returns updated Delaying reject of request 7 for 1 seconds Going to the next request Waking up in 0.9 seconds. Sending delayed reject for request 7 Sending Access-Reject of id 175 to 127.0.0.1 port 37217 EAP-Message = 0x04ae0004 Message-Authenticator = 0x00000000000000000000000000000000 Waking up in 3.9 seconds. Cleaning up request 6 ID 174 with timestamp +6089 Waking up in 0.9 seconds. Cleaning up request 7 ID 175 with timestamp +6089 Ready to process requests. Kindly check my users conf. #test-01 Cleartext-Password := "test-01" # # Please read the documentation file ../doc/processing_users_file, # or 'man 5 users' (after installing the server) for more information. # # This file contains authentication security and configuration # information for each user. Accounting requests are NOT processed # through this file. Instead, see 'acct_users', in this directory. # # The first field is the user's name and can be up to # 253 characters in length. This is followed (on the same line) with # the list of authentication requirements for that user. This can # include password, comm server name, comm server port number, protocol # type (perhaps set by the "hints" file), and huntgroup name (set by # the "huntgroups" file). # # If you are not sure why a particular reply is being sent by the # server, then run the server in debugging mode (radiusd -X), and # you will see which entries in this file are matched. # # When an authentication request is received from the comm server, # these values are tested. Only the first match is used unless the # "Fall-Through" variable is set to "Yes". # # A special user named "DEFAULT" matches on all usernames. # You can have several DEFAULT entries. All entries are processed # in the order they appear in this file. The first entry that # matches the login-request will stop processing unless you use # the Fall-Through variable. # # If you use the database support to turn this file into a .db or .dbm # file, the DEFAULT entries _have_ to be at the end of this file and # you can't have multiple entries for one username. # # Indented (with the tab character) lines following the first # line indicate the configuration values to be passed back to # the comm server to allow the initiation of a user session. # This can include things like the PPP configuration values # or the host to log the user onto. # # You can include another `users' file with `$INCLUDE users.other' # # # For a list of RADIUS attributes, and links to their definitions, # see: # # http://www.freeradius.org/rfc/attributes.html # # # Deny access for a specific user. Note that this entry MUST # be before any other 'Auth-Type' attribute which results in the user # being authenticated. # # Note that there is NO 'Fall-Through' attribute, so the user will not # be given any additional resources. # #lameuser Auth-Type := Reject # Reply-Message = "Your account has been disabled." # # Deny access for a group of users. # # Note that there is NO 'Fall-Through' attribute, so the user will not # be given any additional resources. # #DEFAULT Group == "disabled", Auth-Type := Reject # Reply-Message = "Your account has been disabled." # # # This is a complete entry for "steve". Note that there is no Fall-Through # entry so that no DEFAULT entry will be used, and the user will NOT # get any attributes in addition to the ones listed here. # steve Cleartext-Password := "testing" Auth-Type := pap # Service-Type = Framed-User, # Framed-Protocol = PPP, # Framed-IP-Address = 172.16.3.33, # Framed-IP-Netmask = 255.255.255.0, # Framed-Routing = Broadcast-Listen, # Framed-Filter-Id = "std.ppp", # Framed-MTU = 1500, # Framed-Compression = Van-Jacobsen-TCP-IP # Auth-Type := md5, # Service-Type = Administrative-user, # Framed-Protocol = PPP, # Framed-IP-Address = 172.16.3.33, # Framed-IP-Netmask = 255.255.255.0, # Framed-Routing = Broadcast-Listen, # Framed-Filter-Id = "std.ppp", # Framed-MTU = 1500, # Framed-Compression = Van-Jacobsen-TCP-IP # # This is an entry for a user with a space in their name. # Note the double quotes surrounding the name. # #"John Doe" Cleartext-Password := "hello" # Reply-Message = "Hello, %{User-Name}" # # Dial user back and telnet to the default host for that port # #Deg Cleartext-Password := "ge55ged" # Service-Type = Callback-Login-User, # Login-IP-Host = 0.0.0.0, # Callback-Number = "9,5551212", # Login-Service = Telnet, # Login-TCP-Port = Telnet # # Another complete entry. After the user "dialbk" has logged in, the # connection will be broken and the user will be dialed back after which # he will get a connection to the host "timeshare1". # #dialbk Cleartext-Password := "callme" # Service-Type = Callback-Login-User, # Login-IP-Host = timeshare1, # Login-Service = PortMaster, # Callback-Number = "9,1-800-555-1212" # # user "swilson" will only get a static IP number if he logs in with # a framed protocol on a terminal server in Alphen (see the huntgroups file). # # Note that by setting "Fall-Through", other attributes will be added from # the following DEFAULT entries # #swilson Service-Type == Framed-User, Huntgroup-Name == "alphen" # Framed-IP-Address = 192.168.1.65, # Fall-Through = Yes # # If the user logs in as 'username.shell', then authenticate them # using the default method, give them shell access, and stop processing # the rest of the file. # #DEFAULT Suffix == ".shell" # Service-Type = Login-User, # Login-Service = Telnet, # Login-IP-Host = your.shell.machine # # The rest of this file contains the several DEFAULT entries. # DEFAULT entries match with all login names. # Note that DEFAULT entries can also Fall-Through (see first entry). # A name-value pair from a DEFAULT entry will _NEVER_ override # an already existing name-value pair. # # # Set up different IP address pools for the terminal servers. # Note that the "+" behind the IP address means that this is the "base" # IP address. The Port-Id (S0, S1 etc) will be added to it. # #DEFAULT Service-Type == Framed-User, Huntgroup-Name == "alphen" # Framed-IP-Address = 192.168.1.32+, # Fall-Through = Yes #DEFAULT Service-Type == Framed-User, Huntgroup-Name == "delft" # Framed-IP-Address = 192.168.2.32+, # Fall-Through = Yes # # Sample defaults for all framed connections. # #DEFAULT Service-Type == Framed-User # Framed-IP-Address = 255.255.255.254, # Framed-MTU = 576, # Service-Type = Framed-User, # Fall-Through = Yes # # Default for PPP: dynamic IP address, PPP mode, VJ-compression. # NOTE: we do not use Hint = "PPP", since PPP might also be auto-detected # by the terminal server in which case there may not be a "P" suffix. # The terminal server sends "Framed-Protocol = PPP" for auto PPP. # DEFAULT Framed-Protocol == PPP Framed-Protocol = PPP, Framed-Compression = Van-Jacobson-TCP-IP # # Default for CSLIP: dynamic IP address, SLIP mode, VJ-compression. # DEFAULT Hint == "CSLIP" Framed-Protocol = SLIP, Framed-Compression = Van-Jacobson-TCP-IP # # Default for SLIP: dynamic IP address, SLIP mode. # DEFAULT Hint == "SLIP" Framed-Protocol = SLIP # # Last default: rlogin to our main server. # #DEFAULT # Service-Type = Login-User, # Login-Service = Rlogin, # Login-IP-Host = shellbox.ispdomain.com # # # # Last default: shell on the local terminal server. # # # DEFAULT # Service-Type = Administrative-User # On no match, the user is denied access. Thank you. Drei