On Apr 15, 2024, at 1:18 AM, Jack Carter <jack_carter94@hotmail.com> wrote:

Apologies… lets try again… ... Listening on proxy address :: port 56191 Ready to process requests

And....? http://wiki.freeradius.org/list-help Please read and follow the documentation. When you make it difficult for people to help you, people are less inclined to help you. Alan DeKok.

On Apr 15, 2024, at 1:43 PM, Jack Carter <jack_carter94@hotmail.com> wrote:

Ok.. lets start again…

The link I posted documents what information we need in order to help you. It explicitly says do NOT post the configuration files. It also says to show the server receiving packets. The message you posted didn't follow either recommendation.

I am trying to remove the depreciated use_tunneled_reply in place of updating the outer.session-state but can’t seem to get it working. Users are not authorised after adjusting the config to the following… what am I missing?

Read the documentation and follow it.

I am testing this with: radtest -t mschap test.user password 127.0.0.1:18120 0 testing123

Which doesn't test the process you're trying to debug. If you send packets directly to the inner tunnel, then there's no outer tunnel. If you're doing to test inner/outer tunnel policies, then you have to send the server EAP traffic which will run both the inner and outer policies.

Thanks in advance for any assistance you can provide.

I'm trying. It's not working well.

Jack

Output from freeradisu -X: ... Ready to process requests

And nothing about the server processing packets. How are you going to debug the server packet processing when the logs don't show it processing any packets? Perhaps there's a documentation page you could follow which says exactly what to do. If you're not going to read or follow the documentation, it will be very difficult to solve any configuration problems. Alan DeKok.

Jack Carter <jack_carter94@hotmail.com>:

If I’m using the wrong test method are you able to assist with the correct one? If I run radtest from another instance (having set it up as a client) would that be a valid test?

To test EAP-PEAP or EAP-TLS or EAP-TTLS you need eapol_test, which is packaged with or alongside wpa_supplicant

Ok so firstly… properly read the help wiki and can therefore see your frustrations… apologies. Turns out, thanks to Alan pointing out radtest was only dealing with the inner-tunnel (I’m learning… slowly!), and to Brian for the testing tip, that everything was working after all (two days I won’t get back again!). I have also been able to add a custom attribute to the dictionary allowing me to assign VLANs based on UserGroups. I am seeing a couple of warnings in the debug log… (7)(8)(9) WARNING: Outer and inner identities are the same. User privacy is compromised. (8)(9) pap: WARNING: Auth-Type already set. Not setting to PAP I’m assuming the pap warning is more of an FYI as i’m using eap so can be ignored? How can I resolve the outer and inner identities being the same? Many thanks again for the assistance. Jack FreeRADIUS Version 3.0.21 Copyright (C) 1999-2019 The FreeRADIUS server project and contributors There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE You may redistribute copies of FreeRADIUS under the terms of the GNU General Public License For more information about these matters, see the file named COPYRIGHT Starting - reading configuration files ... including dictionary file /usr/share/freeradius/dictionary including dictionary file /usr/share/freeradius/dictionary.dhcp including dictionary file /usr/share/freeradius/dictionary.vqp including dictionary file /etc/freeradius/3.0/dictionary including configuration file /etc/freeradius/3.0/radiusd.conf including configuration file /etc/freeradius/3.0/proxy.conf including configuration file /etc/freeradius/3.0/clients.conf including files in directory /etc/freeradius/3.0/mods-enabled/ including configuration file /etc/freeradius/3.0/mods-enabled/radutmp including configuration file /etc/freeradius/3.0/mods-enabled/replicate including configuration file /etc/freeradius/3.0/mods-enabled/chap including configuration file /etc/freeradius/3.0/mods-enabled/mschap including configuration file /etc/freeradius/3.0/mods-enabled/ntlm_auth including configuration file /etc/freeradius/3.0/mods-enabled/cache_eap including configuration file /etc/freeradius/3.0/mods-enabled/dynamic_clients including configuration file /etc/freeradius/3.0/mods-enabled/digest including configuration file /etc/freeradius/3.0/mods-enabled/expr including configuration file /etc/freeradius/3.0/mods-enabled/logintime including configuration file /etc/freeradius/3.0/mods-enabled/soh including configuration file /etc/freeradius/3.0/mods-enabled/preprocess including configuration file /etc/freeradius/3.0/mods-enabled/sradutmp including configuration file /etc/freeradius/3.0/mods-enabled/unpack including configuration file /etc/freeradius/3.0/mods-enabled/echo including configuration file /etc/freeradius/3.0/mods-enabled/expiration including configuration file /etc/freeradius/3.0/mods-enabled/pap including configuration file /etc/freeradius/3.0/mods-enabled/always including configuration file /etc/freeradius/3.0/mods-enabled/utf8 including configuration file /etc/freeradius/3.0/mods-enabled/unix including configuration file /etc/freeradius/3.0/mods-enabled/passwd including configuration file /etc/freeradius/3.0/mods-enabled/detail including configuration file /etc/freeradius/3.0/mods-enabled/attr_filter including configuration file /etc/freeradius/3.0/mods-enabled/linelog including configuration file /etc/freeradius/3.0/mods-enabled/eap including configuration file /etc/freeradius/3.0/mods-enabled/detail.log including configuration file /etc/freeradius/3.0/mods-enabled/files including configuration file /etc/freeradius/3.0/mods-enabled/exec including configuration file /etc/freeradius/3.0/mods-enabled/realm including files in directory /etc/freeradius/3.0/policy.d/ including configuration file /etc/freeradius/3.0/policy.d/canonicalization including configuration file /etc/freeradius/3.0/policy.d/dhcp including configuration file /etc/freeradius/3.0/policy.d/debug including configuration file /etc/freeradius/3.0/policy.d/control including configuration file /etc/freeradius/3.0/policy.d/moonshot-targeted-ids including configuration file /etc/freeradius/3.0/policy.d/rfc7542 including configuration file /etc/freeradius/3.0/policy.d/filter including configuration file /etc/freeradius/3.0/policy.d/accounting including configuration file /etc/freeradius/3.0/policy.d/operator-name including configuration file /etc/freeradius/3.0/policy.d/abfab-tr including configuration file /etc/freeradius/3.0/policy.d/cui including configuration file /etc/freeradius/3.0/policy.d/eap including files in directory /etc/freeradius/3.0/sites-enabled/ including configuration file /etc/freeradius/3.0/sites-enabled/inner-tunnel including configuration file /etc/freeradius/3.0/sites-enabled/default main { security { user = "freerad" group = "freerad" allow_core_dumps = no } name = "freeradius" prefix = "/usr" localstatedir = "/var" logdir = "/var/log/freeradius" run_dir = "/var/run/freeradius" } main { name = "freeradius" prefix = "/usr" localstatedir = "/var" sbindir = "/usr/sbin" logdir = "/var/log/freeradius" run_dir = "/var/run/freeradius" libdir = "/usr/lib/freeradius" radacctdir = "/var/log/freeradius/radacct" hostname_lookups = no max_request_time = 30 cleanup_delay = 5 max_requests = 16384 pidfile = "/var/run/freeradius/freeradius.pid" checkrad = "/usr/sbin/checkrad" debug_level = 0 proxy_requests = yes log { stripped_names = no auth = no auth_badpass = no auth_goodpass = no colourise = yes msg_denied = "You are already logged in - access denied" } resources { } security { max_attributes = 200 reject_delay = 1.000000 status_server = yes } } radiusd: #### Loading Realms and Home Servers #### proxy server { retry_delay = 5 retry_count = 3 default_fallback = no dead_time = 120 wake_all_if_all_dead = no } home_server localhost { ipaddr = 127.0.0.1 port = 1812 type = "auth" secret = <<< secret >>> response_window = 20.000000 response_timeouts = 1 max_outstanding = 65536 zombie_period = 40 status_check = "status-server" ping_interval = 30 check_interval = 30 check_timeout = 4 num_answers_to_alive = 3 revive_interval = 120 limit { max_connections = 16 max_requests = 0 lifetime = 0 idle_timeout = 0 } coa { irt = 2 mrt = 16 mrc = 5 mrd = 30 } } home_server_pool my_auth_failover { type = fail-over home_server = localhost } realm example.com <http://example.com/> { auth_pool = my_auth_failover } realm LOCAL { } radiusd: #### Loading Clients #### client localhost { ipaddr = 127.0.0.1 require_message_authenticator = no secret = <<< secret >>> nas_type = "other" proto = "*" limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } client localhost_ipv6 { ipv6addr = ::1 require_message_authenticator = no secret = <<< secret >>> limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } client 3KL-Management { ipaddr = 10.165.11.0/27 require_message_authenticator = yes secret = <<< secret >>> limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } Debugger not attached systemd watchdog is disabled # Creating Auth-Type = mschap # Creating Auth-Type = eap # Creating Auth-Type = PAP # Creating Auth-Type = CHAP # Creating Auth-Type = MS-CHAP # Creating Auth-Type = digest radiusd: #### Instantiating modules #### modules { # Loaded module rlm_radutmp # Loading module "radutmp" from file /etc/freeradius/3.0/mods-enabled/radutmp radutmp { filename = "/var/log/freeradius/radutmp" username = "%{User-Name}" case_sensitive = yes check_with_nas = yes permissions = 384 caller_id = yes } # Loaded module rlm_replicate # Loading module "replicate" from file /etc/freeradius/3.0/mods-enabled/replicate # Loaded module rlm_chap # Loading module "chap" from file /etc/freeradius/3.0/mods-enabled/chap # Loaded module rlm_mschap # Loading module "mschap" from file /etc/freeradius/3.0/mods-enabled/mschap mschap { use_mppe = yes require_encryption = no require_strong = no with_ntdomain_hack = yes passchange { } allow_retry = yes winbind_retry_with_normalised_username = no } # Loaded module rlm_exec # Loading module "ntlm_auth" from file /etc/freeradius/3.0/mods-enabled/ntlm_auth exec ntlm_auth { wait = yes program = "/path/to/ntlm_auth --request-nt-key --domain=MYDOMAIN --username=%{mschap:User-Name} --password=%{User-Password}" shell_escape = yes } # Loaded module rlm_cache # Loading module "cache_eap" from file /etc/freeradius/3.0/mods-enabled/cache_eap cache cache_eap { driver = "rlm_cache_rbtree" key = "%{%{control:State}:-%{%{reply:State}:-%{State}}}" ttl = 15 max_entries = 0 epoch = 0 add_stats = no } # Loaded module rlm_dynamic_clients # Loading module "dynamic_clients" from file /etc/freeradius/3.0/mods-enabled/dynamic_clients # Loaded module rlm_digest # Loading module "digest" from file /etc/freeradius/3.0/mods-enabled/digest # Loaded module rlm_expr # Loading module "expr" from file /etc/freeradius/3.0/mods-enabled/expr expr { safe_characters = "@abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789.-_: /äéöüàâæçèéêëîïôœùûüaÿÄÉÖÜßÀÂÆÇÈÉÊËÎÏÔŒÙÛÜŸ" } # Loaded module rlm_logintime # Loading module "logintime" from file /etc/freeradius/3.0/mods-enabled/logintime logintime { minimum_timeout = 60 } # Loaded module rlm_soh # Loading module "soh" from file /etc/freeradius/3.0/mods-enabled/soh soh { dhcp = yes } # Loaded module rlm_preprocess # Loading module "preprocess" from file /etc/freeradius/3.0/mods-enabled/preprocess preprocess { huntgroups = "/etc/freeradius/3.0/mods-config/preprocess/huntgroups" hints = "/etc/freeradius/3.0/mods-config/preprocess/hints" with_ascend_hack = no ascend_channels_per_line = 23 with_ntdomain_hack = no with_specialix_jetstream_hack = no with_cisco_vsa_hack = no with_alvarion_vsa_hack = no } # Loading module "sradutmp" from file /etc/freeradius/3.0/mods-enabled/sradutmp radutmp sradutmp { filename = "/var/log/freeradius/sradutmp" username = "%{User-Name}" case_sensitive = yes check_with_nas = yes permissions = 420 caller_id = no } # Loaded module rlm_unpack # Loading module "unpack" from file /etc/freeradius/3.0/mods-enabled/unpack # Loading module "echo" from file /etc/freeradius/3.0/mods-enabled/echo exec echo { wait = yes program = "/bin/echo %{User-Name}" input_pairs = "request" output_pairs = "reply" shell_escape = yes } # Loaded module rlm_expiration # Loading module "expiration" from file /etc/freeradius/3.0/mods-enabled/expiration # Loaded module rlm_pap # Loading module "pap" from file /etc/freeradius/3.0/mods-enabled/pap pap { normalise = yes } # Loaded module rlm_always # Loading module "reject" from file /etc/freeradius/3.0/mods-enabled/always always reject { rcode = "reject" simulcount = 0 mpp = no } # Loading module "fail" from file /etc/freeradius/3.0/mods-enabled/always always fail { rcode = "fail" simulcount = 0 mpp = no } # Loading module "ok" from file /etc/freeradius/3.0/mods-enabled/always always ok { rcode = "ok" simulcount = 0 mpp = no } # Loading module "handled" from file /etc/freeradius/3.0/mods-enabled/always always handled { rcode = "handled" simulcount = 0 mpp = no } # Loading module "invalid" from file /etc/freeradius/3.0/mods-enabled/always always invalid { rcode = "invalid" simulcount = 0 mpp = no } # Loading module "userlock" from file /etc/freeradius/3.0/mods-enabled/always always userlock { rcode = "userlock" simulcount = 0 mpp = no } # Loading module "notfound" from file /etc/freeradius/3.0/mods-enabled/always always notfound { rcode = "notfound" simulcount = 0 mpp = no } # Loading module "noop" from file /etc/freeradius/3.0/mods-enabled/always always noop { rcode = "noop" simulcount = 0 mpp = no } # Loading module "updated" from file /etc/freeradius/3.0/mods-enabled/always always updated { rcode = "updated" simulcount = 0 mpp = no } # Loaded module rlm_utf8 # Loading module "utf8" from file /etc/freeradius/3.0/mods-enabled/utf8 # Loaded module rlm_unix # Loading module "unix" from file /etc/freeradius/3.0/mods-enabled/unix unix { radwtmp = "/var/log/freeradius/radwtmp" } Creating attribute Unix-Group # Loaded module rlm_passwd # Loading module "etc_passwd" from file /etc/freeradius/3.0/mods-enabled/passwd passwd etc_passwd { filename = "/etc/passwd" format = "*User-Name:Crypt-Password:" delimiter = ":" ignore_nislike = no ignore_empty = yes allow_multiple_keys = no hash_size = 100 } # Loaded module rlm_detail # Loading module "detail" from file /etc/freeradius/3.0/mods-enabled/detail detail { filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loaded module rlm_attr_filter # Loading module "attr_filter.post-proxy" from file /etc/freeradius/3.0/mods-enabled/attr_filter attr_filter attr_filter.post-proxy { filename = "/etc/freeradius/3.0/mods-config/attr_filter/post-proxy" key = "%{Realm}" relaxed = no } # Loading module "attr_filter.pre-proxy" from file /etc/freeradius/3.0/mods-enabled/attr_filter attr_filter attr_filter.pre-proxy { filename = "/etc/freeradius/3.0/mods-config/attr_filter/pre-proxy" key = "%{Realm}" relaxed = no } # Loading module "attr_filter.access_reject" from file /etc/freeradius/3.0/mods-enabled/attr_filter attr_filter attr_filter.access_reject { filename = "/etc/freeradius/3.0/mods-config/attr_filter/access_reject" key = "%{User-Name}" relaxed = no } # Loading module "attr_filter.access_challenge" from file /etc/freeradius/3.0/mods-enabled/attr_filter attr_filter attr_filter.access_challenge { filename = "/etc/freeradius/3.0/mods-config/attr_filter/access_challenge" key = "%{User-Name}" relaxed = no } # Loading module "attr_filter.accounting_response" from file /etc/freeradius/3.0/mods-enabled/attr_filter attr_filter attr_filter.accounting_response { filename = "/etc/freeradius/3.0/mods-config/attr_filter/accounting_response" key = "%{User-Name}" relaxed = no } # Loaded module rlm_linelog # Loading module "linelog" from file /etc/freeradius/3.0/mods-enabled/linelog linelog { filename = "/var/log/freeradius/linelog" escape_filenames = no syslog_severity = "info" permissions = 384 format = "This is a log message for %{User-Name}" reference = "messages.%{%{reply:Packet-Type}:-default}" } # Loading module "log_accounting" from file /etc/freeradius/3.0/mods-enabled/linelog linelog log_accounting { filename = "/var/log/freeradius/linelog-accounting" escape_filenames = no syslog_severity = "info" permissions = 384 format = "" reference = "Accounting-Request.%{%{Acct-Status-Type}:-unknown}" } # Loaded module rlm_eap # Loading module "eap" from file /etc/freeradius/3.0/mods-enabled/eap eap { default_eap_type = "peap" timer_expire = 60 ignore_unknown_eap_types = no cisco_accounting_username_bug = no max_sessions = 16384 } # Loading module "auth_log" from file /etc/freeradius/3.0/mods-enabled/detail.log detail auth_log { filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loading module "reply_log" from file /etc/freeradius/3.0/mods-enabled/detail.log detail reply_log { filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/reply-detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loading module "pre_proxy_log" from file /etc/freeradius/3.0/mods-enabled/detail.log detail pre_proxy_log { filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/pre-proxy-detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loading module "post_proxy_log" from file /etc/freeradius/3.0/mods-enabled/detail.log detail post_proxy_log { filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/post-proxy-detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loaded module rlm_files # Loading module "files" from file /etc/freeradius/3.0/mods-enabled/files files { filename = "/etc/freeradius/3.0/mods-config/files/authorize" acctusersfile = "/etc/freeradius/3.0/mods-config/files/accounting" preproxy_usersfile = "/etc/freeradius/3.0/mods-config/files/pre-proxy" } # Loading module "exec" from file /etc/freeradius/3.0/mods-enabled/exec exec { wait = no input_pairs = "request" shell_escape = yes timeout = 10 } # Loaded module rlm_realm # Loading module "IPASS" from file /etc/freeradius/3.0/mods-enabled/realm realm IPASS { format = "prefix" delimiter = "/" ignore_default = no ignore_null = no } # Loading module "suffix" from file /etc/freeradius/3.0/mods-enabled/realm realm suffix { format = "suffix" delimiter = "@" ignore_default = no ignore_null = no } # Loading module "bangpath" from file /etc/freeradius/3.0/mods-enabled/realm realm bangpath { format = "prefix" delimiter = "!" ignore_default = no ignore_null = no } # Loading module "realmpercent" from file /etc/freeradius/3.0/mods-enabled/realm realm realmpercent { format = "suffix" delimiter = "%" ignore_default = no ignore_null = no } # Loading module "ntdomain" from file /etc/freeradius/3.0/mods-enabled/realm realm ntdomain { format = "prefix" delimiter = "\\" ignore_default = no ignore_null = no } instantiate { } # Instantiating module "mschap" from file /etc/freeradius/3.0/mods-enabled/mschap rlm_mschap (mschap): using internal authentication # Instantiating module "cache_eap" from file /etc/freeradius/3.0/mods-enabled/cache_eap rlm_cache (cache_eap): Driver rlm_cache_rbtree (module rlm_cache_rbtree) loaded and linked # Instantiating module "logintime" from file /etc/freeradius/3.0/mods-enabled/logintime # Instantiating module "preprocess" from file /etc/freeradius/3.0/mods-enabled/preprocess reading pairlist file /etc/freeradius/3.0/mods-config/preprocess/huntgroups reading pairlist file /etc/freeradius/3.0/mods-config/preprocess/hints # Instantiating module "expiration" from file /etc/freeradius/3.0/mods-enabled/expiration # Instantiating module "pap" from file /etc/freeradius/3.0/mods-enabled/pap # Instantiating module "reject" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "fail" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "ok" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "handled" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "invalid" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "userlock" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "notfound" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "noop" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "updated" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "etc_passwd" from file /etc/freeradius/3.0/mods-enabled/passwd rlm_passwd: nfields: 3 keyfield 0(User-Name) listable: no # Instantiating module "detail" from file /etc/freeradius/3.0/mods-enabled/detail # Instantiating module "attr_filter.post-proxy" from file /etc/freeradius/3.0/mods-enabled/attr_filter reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/post-proxy # Instantiating module "attr_filter.pre-proxy" from file /etc/freeradius/3.0/mods-enabled/attr_filter reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/pre-proxy # Instantiating module "attr_filter.access_reject" from file /etc/freeradius/3.0/mods-enabled/attr_filter reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/access_reject # Instantiating module "attr_filter.access_challenge" from file /etc/freeradius/3.0/mods-enabled/attr_filter reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/access_challenge # Instantiating module "attr_filter.accounting_response" from file /etc/freeradius/3.0/mods-enabled/attr_filter reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/accounting_response # Instantiating module "linelog" from file /etc/freeradius/3.0/mods-enabled/linelog # Instantiating module "log_accounting" from file /etc/freeradius/3.0/mods-enabled/linelog # Instantiating module "eap" from file /etc/freeradius/3.0/mods-enabled/eap # Linked to sub-module rlm_eap_tls tls { tls = "tls-common" } tls-config tls-common { verify_depth = 0 ca_path = "/etc/freeradius/3.0/certs" pem_file_type = yes private_key_file = "/etc/ssl/private/ssl-cert-snakeoil.key" certificate_file = "/etc/ssl/certs/ssl-cert-snakeoil.pem" ca_file = "/etc/ssl/certs/ca-certificates.crt" private_key_password = <<< secret >>> dh_file = "/etc/freeradius/3.0/certs/dh" fragment_size = 1024 include_length = yes auto_chain = yes check_crl = no check_all_crl = no cipher_list = "HIGH" ecdh_curve = "prime256v1" tls_max_version = "1.2" tls_min_version = "1.2" cache { enable = yes lifetime = 24 max_entries = 255 } verify { skip_if_ocsp_ok = no } ocsp { enable = no override_cert_url = yes url = "http://127.0.0.1/ocsp/ <http://127.0.0.1/ocsp/>" use_nonce = yes timeout = 0 softfail = no } } # Linked to sub-module rlm_eap_ttls ttls { tls = "tls-common" default_eap_type = "md5" copy_request_to_tunnel = no use_tunneled_reply = no virtual_server = "inner-tunnel" include_length = yes require_client_cert = no } tls: Using cached TLS configuration from previous invocation # Linked to sub-module rlm_eap_peap peap { tls = "tls-peap" default_eap_type = "mschapv2" copy_request_to_tunnel = no use_tunneled_reply = no proxy_tunneled_request_as_eap = yes virtual_server = "inner-tunnel" soh = no require_client_cert = no } tls-config tls-peap { verify_depth = 0 ca_path = "/etc/freeradius/3.0/certs" pem_file_type = yes private_key_file = "/etc/freeradius/3.0/certs/letsencrypt/privkey.pem" certificate_file = "/etc/freeradius/3.0/certs/letsencrypt/fullchain.pem" dh_file = "/etc/freeradius/3.0/certs/dh" fragment_size = 1024 include_length = yes auto_chain = yes check_crl = no check_all_crl = no cipher_list = "HIGH" ecdh_curve = "prime256v1" tls_max_version = "1.2" tls_min_version = "1.2" cache { enable = yes lifetime = 24 max_entries = 255 } verify { skip_if_ocsp_ok = no } ocsp { enable = no override_cert_url = yes url = "http://127.0.0.1/ocsp/ <http://127.0.0.1/ocsp/>" use_nonce = yes timeout = 0 softfail = no } } # Linked to sub-module rlm_eap_mschapv2 mschapv2 { with_ntdomain_hack = no send_error = no } # Instantiating module "auth_log" from file /etc/freeradius/3.0/mods-enabled/detail.log rlm_detail (auth_log): 'User-Password' suppressed, will not appear in detail output # Instantiating module "reply_log" from file /etc/freeradius/3.0/mods-enabled/detail.log # Instantiating module "pre_proxy_log" from file /etc/freeradius/3.0/mods-enabled/detail.log # Instantiating module "post_proxy_log" from file /etc/freeradius/3.0/mods-enabled/detail.log # Instantiating module "files" from file /etc/freeradius/3.0/mods-enabled/files reading pairlist file /etc/freeradius/3.0/mods-config/files/authorize reading pairlist file /etc/freeradius/3.0/mods-config/files/accounting reading pairlist file /etc/freeradius/3.0/mods-config/files/pre-proxy # Instantiating module "IPASS" from file /etc/freeradius/3.0/mods-enabled/realm # Instantiating module "suffix" from file /etc/freeradius/3.0/mods-enabled/realm # Instantiating module "bangpath" from file /etc/freeradius/3.0/mods-enabled/realm # Instantiating module "realmpercent" from file /etc/freeradius/3.0/mods-enabled/realm # Instantiating module "ntdomain" from file /etc/freeradius/3.0/mods-enabled/realm } # modules radiusd: #### Loading Virtual Servers #### server { # from file /etc/freeradius/3.0/radiusd.conf } # server server inner-tunnel { # from file /etc/freeradius/3.0/sites-enabled/inner-tunnel # Loading authenticate {...} # Loading authorize {...} Ignoring "sql" (see raddb/mods-available/README.rst) Ignoring "ldap" (see raddb/mods-available/README.rst) # Loading session {...} # Loading post-proxy {...} # Loading post-auth {...} } # server inner-tunnel server default { # from file /etc/freeradius/3.0/sites-enabled/default # Loading authenticate {...} # Loading authorize {...} # Loading preacct {...} # Loading accounting {...} # Loading post-proxy {...} # Loading post-auth {...} } # server default radiusd: #### Opening IP addresses and Ports #### listen { type = "auth" ipaddr = 127.0.0.1 port = 18120 } listen { type = "auth" ipaddr = * port = 0 limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } listen { type = "acct" ipaddr = * port = 0 limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } listen { type = "auth" ipv6addr = :: port = 0 limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } listen { type = "acct" ipv6addr = :: port = 0 limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } Listening on auth address 127.0.0.1 port 18120 bound to server inner-tunnel Listening on auth address * port 1812 bound to server default Listening on acct address * port 1813 bound to server default Listening on auth address :: port 1812 bound to server default Listening on acct address :: port 1813 bound to server default Listening on proxy address * port 38684 Listening on proxy address :: port 34119 Ready to process requests (0) Received Accounting-Request Id 62 from 10.165.11.22:36835 to 10.165.11.10:1813 length 282 (0) Acct-Status-Type = Stop (0) Acct-Authentic = RADIUS (0) User-Name = "jack.carter" (0) NAS-IP-Address = 10.165.11.22 (0) Framed-IP-Address = 10.165.3.53 (0) NAS-Identifier = "f69fc26a572e" (0) Called-Station-Id = "F6-9F-C2-6A-57-2E:3 Kiln Lane" (0) NAS-Port-Type = Wireless-802.11 (0) Service-Type = Framed-User (0) Calling-Station-Id = "C4-C1-7D-A3-4A-9D" (0) Connect-Info = "CONNECT 0Mbps 802.11b" (0) Acct-Session-Id = "9DA924B0334CF415" (0) Acct-Multi-Session-Id = "932745FB80A23149" (0) Mobility-Domain-Id = 20677 (0) WLAN-Pairwise-Cipher = 1027076 (0) WLAN-Group-Cipher = 1027076 (0) WLAN-AKM-Suite = 1027075 (0) WLAN-Group-Mgmt-Cipher = 1027078 (0) Event-Timestamp = "Apr 16 2024 11:11:38 BST" (0) Acct-Delay-Time = 0 (0) Acct-Session-Time = 1257 (0) Acct-Input-Packets = 4840 (0) Acct-Output-Packets = 9025 (0) Acct-Input-Octets = 578291 (0) Acct-Input-Gigawords = 0 (0) Acct-Output-Octets = 5997969 (0) Acct-Output-Gigawords = 0 (0) Acct-Terminate-Cause = User-Request (0) # Executing section preacct from file /etc/freeradius/3.0/sites-enabled/default (0) preacct { (0) [preprocess] = ok (0) policy acct_unique { (0) update request { (0) &Tmp-String-9 := "ai:" (0) } # update request = noop (0) if (("%{hex:&Class}" =~ /^%{hex:&Tmp-String-9}/) && ("%{string:&Class}" =~ /^ai:([0-9a-f]{32})/i)) { (0) EXPAND %{hex:&Class} (0) --> (0) EXPAND ^%{hex:&Tmp-String-9} (0) --> ^61693a (0) if (("%{hex:&Class}" =~ /^%{hex:&Tmp-String-9}/) && ("%{string:&Class}" =~ /^ai:([0-9a-f]{32})/i)) -> FALSE (0) else { (0) update request { (0) EXPAND %{md5:%{User-Name},%{Acct-Session-ID},%{%{NAS-IPv6-Address}:-%{NAS-IP-Address}},%{NAS-Identifier},%{NAS-Port-ID},%{NAS-Port}} (0) --> 529a7f11865343244101483d511a3368 (0) &Acct-Unique-Session-Id := 529a7f11865343244101483d511a3368 (0) } # update request = noop (0) } # else = noop (0) } # policy acct_unique = noop (0) suffix: Checking for suffix after "@" (0) suffix: No '@' in User-Name = "jack.carter", looking up realm NULL (0) suffix: No such realm "NULL" (0) [suffix] = noop (0) [files] = noop (0) } # preacct = ok (0) # Executing section accounting from file /etc/freeradius/3.0/sites-enabled/default (0) accounting { (0) detail: EXPAND /var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/detail-%Y%m%d (0) detail: --> /var/log/freeradius/radacct/10.165.11.22/detail-20240416 (0) detail: /var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/detail-%Y%m%d expands to /var/log/freeradius/radacct/10.165.11.22/detail-20240416 (0) detail: EXPAND %t (0) detail: --> Tue Apr 16 11:11:38 2024 (0) [detail] = ok (0) [unix] = ok (0) [exec] = noop (0) attr_filter.accounting_response: EXPAND %{User-Name} (0) attr_filter.accounting_response: --> jack.carter (0) attr_filter.accounting_response: Matched entry DEFAULT at line 12 (0) [attr_filter.accounting_response] = updated (0) } # accounting = updated (0) Sent Accounting-Response Id 62 from 10.165.11.10:1813 to 10.165.11.22:36835 length 0 (0) Finished request (0) Cleaning up request packet ID 62 with timestamp +6 Ready to process requests (1) Received Access-Request Id 63 from 10.165.11.22:60615 to 10.165.11.10:1812 length 255 (1) User-Name = "jack.carter" (1) NAS-IP-Address = 10.165.11.22 (1) NAS-Identifier = "f69fc26a572e" (1) Called-Station-Id = "F6-9F-C2-6A-57-2E:3 Kiln Lane" (1) NAS-Port-Type = Wireless-802.11 (1) Service-Type = Framed-User (1) Calling-Station-Id = "C4-C1-7D-A3-4A-9D" (1) Connect-Info = "CONNECT 0Mbps 802.11b" (1) Acct-Session-Id = "52716E330C1C872A" (1) Acct-Multi-Session-Id = "F0FA9E0972743E4E" (1) Mobility-Domain-Id = 20677 (1) WLAN-Pairwise-Cipher = 1027076 (1) WLAN-Group-Cipher = 1027076 (1) WLAN-AKM-Suite = 1027075 (1) WLAN-Group-Mgmt-Cipher = 1027078 (1) Filter-Id = "wpa-eap" (1) Framed-MTU = 1002 (1) EAP-Message = 0x02e60010016a61636b2e636172746572 (1) Message-Authenticator = 0x0d8d94451b553e8f2361583ebee78b1e (1) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (1) authorize { (1) policy filter_username { (1) if (&User-Name) { (1) if (&User-Name) -> TRUE (1) if (&User-Name) { (1) if (&User-Name =~ / /) { (1) if (&User-Name =~ / /) -> FALSE (1) if (&User-Name =~ /@[^@]*@/ ) { (1) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (1) if (&User-Name =~ /\.\./ ) { (1) if (&User-Name =~ /\.\./ ) -> FALSE (1) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) { (1) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE (1) if (&User-Name =~ /\.$/) { (1) if (&User-Name =~ /\.$/) -> FALSE (1) if (&User-Name =~ /@\./) { (1) if (&User-Name =~ /@\./) -> FALSE (1) } # if (&User-Name) = notfound (1) } # policy filter_username = notfound (1) [preprocess] = ok (1) [chap] = noop (1) [mschap] = noop (1) [digest] = noop (1) suffix: Checking for suffix after "@" (1) suffix: No '@' in User-Name = "jack.carter", looking up realm NULL (1) suffix: No such realm "NULL" (1) [suffix] = noop (1) eap: Peer sent EAP Response (code 2) ID 230 length 16 (1) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize (1) [eap] = ok (1) } # authorize = ok (1) Found Auth-Type = eap (1) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (1) authenticate { (1) eap: Peer sent packet with method EAP Identity (1) (1) eap: Calling submodule eap_peap to process data (1) eap_peap: Initiating new TLS session (1) eap_peap: [eaptls start] = request (1) eap: Sending EAP Request (code 1) ID 231 length 6 (1) eap: EAP session adding &reply:State = 0xce3ea9c4ced9b078 (1) [eap] = handled (1) } # authenticate = handled (1) Using Post-Auth-Type Challenge (1) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (1) Challenge { ... } # empty sub-section is ignored (1) Sent Access-Challenge Id 63 from 10.165.11.10:1812 to 10.165.11.22:60615 length 0 (1) EAP-Message = 0x01e700061920 (1) Message-Authenticator = 0x00000000000000000000000000000000 (1) State = 0xce3ea9c4ced9b0788bc56028040d79d2 (1) Finished request Waking up in 4.9 seconds. (2) Received Access-Request Id 64 from 10.165.11.22:60615 to 10.165.11.10:1812 length 418 (2) User-Name = "jack.carter" (2) NAS-IP-Address = 10.165.11.22 (2) NAS-Identifier = "f69fc26a572e" (2) Called-Station-Id = "F6-9F-C2-6A-57-2E:3 Kiln Lane" (2) NAS-Port-Type = Wireless-802.11 (2) Service-Type = Framed-User (2) Calling-Station-Id = "C4-C1-7D-A3-4A-9D" (2) Connect-Info = "CONNECT 0Mbps 802.11b" (2) Acct-Session-Id = "52716E330C1C872A" (2) Acct-Multi-Session-Id = "F0FA9E0972743E4E" (2) Mobility-Domain-Id = 20677 (2) WLAN-Pairwise-Cipher = 1027076 (2) WLAN-Group-Cipher = 1027076 (2) WLAN-AKM-Suite = 1027075 (2) WLAN-Group-Mgmt-Cipher = 1027078 (2) Filter-Id = "wpa-eap" (2) Framed-MTU = 1002 (2) EAP-Message = 0x02e700a119800000009716030100920100008e0303661e4ee708bddb3f74f679ea27704191589fae320191a5596b7ce622204245e300002c00ffc02cc02bc024c023c00ac009c008c030c02fc028c027c014c013c012009d009c003d003c0035002f000a01000039000a00080006001700180019000b00020100000d00120010040102010501060104030203050306030005000501000000000012000000170000 (2) State = 0xce3ea9c4ced9b0788bc56028040d79d2 (2) Message-Authenticator = 0xe370bb65986b9a0370fa874cb614b995 (2) session-state: No cached attributes (2) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (2) authorize { (2) policy filter_username { (2) if (&User-Name) { (2) if (&User-Name) -> TRUE (2) if (&User-Name) { (2) if (&User-Name =~ / /) { (2) if (&User-Name =~ / /) -> FALSE (2) if (&User-Name =~ /@[^@]*@/ ) { (2) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (2) if (&User-Name =~ /\.\./ ) { (2) if (&User-Name =~ /\.\./ ) -> FALSE (2) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) { (2) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE (2) if (&User-Name =~ /\.$/) { (2) if (&User-Name =~ /\.$/) -> FALSE (2) if (&User-Name =~ /@\./) { (2) if (&User-Name =~ /@\./) -> FALSE (2) } # if (&User-Name) = notfound (2) } # policy filter_username = notfound (2) [preprocess] = ok (2) [chap] = noop (2) [mschap] = noop (2) [digest] = noop (2) suffix: Checking for suffix after "@" (2) suffix: No '@' in User-Name = "jack.carter", looking up realm NULL (2) suffix: No such realm "NULL" (2) [suffix] = noop (2) eap: Peer sent EAP Response (code 2) ID 231 length 161 (2) eap: Continuing tunnel setup (2) [eap] = ok (2) } # authorize = ok (2) Found Auth-Type = eap (2) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (2) authenticate { (2) eap: Expiring EAP session with state 0xce3ea9c4ced9b078 (2) eap: Finished EAP session with state 0xce3ea9c4ced9b078 (2) eap: Previous EAP request found for state 0xce3ea9c4ced9b078, released from the list (2) eap: Peer sent packet with method EAP PEAP (25) (2) eap: Calling submodule eap_peap to process data (2) eap_peap: Continuing EAP-TLS (2) eap_peap: Peer indicated complete TLS record size will be 151 bytes (2) eap_peap: Got complete TLS record (151 bytes) (2) eap_peap: [eaptls verify] = length included (2) eap_peap: (other): before SSL initialization (2) eap_peap: TLS_accept: before SSL initialization (2) eap_peap: TLS_accept: before SSL initialization (2) eap_peap: <<< recv TLS 1.3 [length 0092] (2) eap_peap: TLS_accept: SSLv3/TLS read client hello (2) eap_peap: >>> send TLS 1.2 [length 005d] (2) eap_peap: TLS_accept: SSLv3/TLS write server hello (2) eap_peap: >>> send TLS 1.2 [length 095b] (2) eap_peap: TLS_accept: SSLv3/TLS write certificate (2) eap_peap: >>> send TLS 1.2 [length 0094] (2) eap_peap: TLS_accept: SSLv3/TLS write key exchange (2) eap_peap: >>> send TLS 1.2 [length 0004] (2) eap_peap: TLS_accept: SSLv3/TLS write server done (2) eap_peap: TLS_accept: Need to read more data: SSLv3/TLS write server done (2) eap_peap: TLS - In Handshake Phase (2) eap_peap: TLS - got 2660 bytes of data (2) eap_peap: [eaptls process] = handled (2) eap: Sending EAP Request (code 1) ID 232 length 1012 (2) eap: EAP session adding &reply:State = 0xce3ea9c4cfd6b078 (2) [eap] = handled (2) } # authenticate = handled (2) Using Post-Auth-Type Challenge (2) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (2) Challenge { ... } # empty sub-section is ignored (2) Sent Access-Challenge Id 64 from 10.165.11.10:1812 to 10.165.11.22:60615 length 0 (2) EAP-Message = 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 (2) Message-Authenticator = 0x00000000000000000000000000000000 (2) State = 0xce3ea9c4cfd6b0788bc56028040d79d2 (2) Finished request Waking up in 4.9 seconds. —— (7) Received Access-Request Id 69 from 10.165.11.22:60615 to 10.165.11.10:1812 length 304 (7) User-Name = "jack.carter" (7) NAS-IP-Address = 10.165.11.22 (7) NAS-Identifier = "f69fc26a572e" (7) Called-Station-Id = "F6-9F-C2-6A-57-2E:3 Kiln Lane" (7) NAS-Port-Type = Wireless-802.11 (7) Service-Type = Framed-User (7) Calling-Station-Id = "C4-C1-7D-A3-4A-9D" (7) Connect-Info = "CONNECT 0Mbps 802.11b" (7) Acct-Session-Id = "52716E330C1C872A" (7) Acct-Multi-Session-Id = "F0FA9E0972743E4E" (7) Mobility-Domain-Id = 20677 (7) WLAN-Pairwise-Cipher = 1027076 (7) WLAN-Group-Cipher = 1027076 (7) WLAN-AKM-Suite = 1027075 (7) WLAN-Group-Mgmt-Cipher = 1027078 (7) Filter-Id = "wpa-eap" (7) Framed-MTU = 1002 (7) EAP-Message = 0x02ec002f190017030300243ec52a65400bea8b1f0a6c2c7b6f6c4d83cad95b595a987cf72f0e7234312d38a55b3be2 (7) State = 0xce3ea9c4cbd2b0788bc56028040d79d2 (7) Message-Authenticator = 0x2ef79cf3e053c384b786948a6a22974f (7) Restoring &session-state (7) &session-state:TLS-Session-Cipher-Suite = "ECDHE-ECDSA-AES256-GCM-SHA384" (7) &session-state:TLS-Session-Version = "TLS 1.2" (7) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (7) authorize { (7) policy filter_username { (7) if (&User-Name) { (7) if (&User-Name) -> TRUE (7) if (&User-Name) { (7) if (&User-Name =~ / /) { (7) if (&User-Name =~ / /) -> FALSE (7) if (&User-Name =~ /@[^@]*@/ ) { (7) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (7) if (&User-Name =~ /\.\./ ) { (7) if (&User-Name =~ /\.\./ ) -> FALSE (7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) { (7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE (7) if (&User-Name =~ /\.$/) { (7) if (&User-Name =~ /\.$/) -> FALSE (7) if (&User-Name =~ /@\./) { (7) if (&User-Name =~ /@\./) -> FALSE (7) } # if (&User-Name) = notfound (7) } # policy filter_username = notfound (7) [preprocess] = ok (7) [chap] = noop (7) [mschap] = noop (7) [digest] = noop (7) suffix: Checking for suffix after "@" (7) suffix: No '@' in User-Name = "jack.carter", looking up realm NULL (7) suffix: No such realm "NULL" (7) [suffix] = noop (7) eap: Peer sent EAP Response (code 2) ID 236 length 47 (7) eap: Continuing tunnel setup (7) [eap] = ok (7) } # authorize = ok (7) Found Auth-Type = eap (7) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (7) authenticate { (7) eap: Expiring EAP session with state 0xce3ea9c4cbd2b078 (7) eap: Finished EAP session with state 0xce3ea9c4cbd2b078 (7) eap: Previous EAP request found for state 0xce3ea9c4cbd2b078, released from the list (7) eap: Peer sent packet with method EAP PEAP (25) (7) eap: Calling submodule eap_peap to process data (7) eap_peap: Continuing EAP-TLS (7) eap_peap: [eaptls verify] = ok (7) eap_peap: Done initial handshake (7) eap_peap: [eaptls process] = ok (7) eap_peap: Session established. Decoding tunneled attributes (7) eap_peap: PEAP state WAITING FOR INNER IDENTITY (7) eap_peap: Identity - jack.carter (7) eap_peap: Got inner identity 'jack.carter' (7) eap_peap: Setting default EAP type for tunneled EAP session (7) eap_peap: Got tunneled request (7) eap_peap: EAP-Message = 0x02ec0010016a61636b2e636172746572 (7) eap_peap: Setting User-Name to jack.carter (7) eap_peap: Sending tunneled request to inner-tunnel (7) eap_peap: EAP-Message = 0x02ec0010016a61636b2e636172746572 (7) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1 (7) eap_peap: User-Name = "jack.carter" (7) Virtual server inner-tunnel received request (7) EAP-Message = 0x02ec0010016a61636b2e636172746572 (7) FreeRADIUS-Proxied-To = 127.0.0.1 (7) User-Name = "jack.carter" (7) WARNING: Outer and inner identities are the same. User privacy is compromised. (7) server inner-tunnel { (7) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/inner-tunnel (7) authorize { (7) policy filter_username { (7) if (&User-Name) { (7) if (&User-Name) -> TRUE (7) if (&User-Name) { (7) if (&User-Name =~ / /) { (7) if (&User-Name =~ / /) -> FALSE (7) if (&User-Name =~ /@[^@]*@/ ) { (7) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (7) if (&User-Name =~ /\.\./ ) { (7) if (&User-Name =~ /\.\./ ) -> FALSE (7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) { (7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE (7) if (&User-Name =~ /\.$/) { (7) if (&User-Name =~ /\.$/) -> FALSE (7) if (&User-Name =~ /@\./) { (7) if (&User-Name =~ /@\./) -> FALSE (7) } # if (&User-Name) = notfound (7) } # policy filter_username = notfound (7) [chap] = noop (7) [mschap] = noop (7) suffix: Checking for suffix after "@" (7) suffix: No '@' in User-Name = "jack.carter", looking up realm NULL (7) suffix: No such realm "NULL" (7) [suffix] = noop (7) update control { (7) &Proxy-To-Realm := LOCAL (7) } # update control = noop (7) eap: Peer sent EAP Response (code 2) ID 236 length 16 (7) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize (7) [eap] = ok (7) } # authorize = ok (7) Found Auth-Type = eap (7) # Executing group from file /etc/freeradius/3.0/sites-enabled/inner-tunnel (7) authenticate { (7) eap: Peer sent packet with method EAP Identity (1) (7) eap: Calling submodule eap_mschapv2 to process data (7) eap_mschapv2: Issuing Challenge (7) eap: Sending EAP Request (code 1) ID 237 length 43 (7) eap: EAP session adding &reply:State = 0x4944d27f49a9c81c (7) [eap] = handled (7) } # authenticate = handled (7) } # server inner-tunnel (7) Virtual server sending reply (7) EAP-Message = 0x01ed002b1a01ed002610d3fe9ff9fcf9151f4c65b34113d160cf667265657261646975732d332e302e3231 (7) Message-Authenticator = 0x00000000000000000000000000000000 (7) State = 0x4944d27f49a9c81c0486e93b4a708ee8 (7) eap_peap: Got tunneled reply code 11 (7) eap_peap: EAP-Message = 0x01ed002b1a01ed002610d3fe9ff9fcf9151f4c65b34113d160cf667265657261646975732d332e302e3231 (7) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (7) eap_peap: State = 0x4944d27f49a9c81c0486e93b4a708ee8 (7) eap_peap: Got tunneled reply RADIUS code 11 (7) eap_peap: EAP-Message = 0x01ed002b1a01ed002610d3fe9ff9fcf9151f4c65b34113d160cf667265657261646975732d332e302e3231 (7) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (7) eap_peap: State = 0x4944d27f49a9c81c0486e93b4a708ee8 (7) eap_peap: Got tunneled Access-Challenge (7) eap: Sending EAP Request (code 1) ID 237 length 74 (7) eap: EAP session adding &reply:State = 0xce3ea9c4c8d3b078 (7) [eap] = handled (7) } # authenticate = handled (7) Using Post-Auth-Type Challenge (7) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (7) Challenge { ... } # empty sub-section is ignored (7) session-state: Saving cached attributes (7) TLS-Session-Cipher-Suite = "ECDHE-ECDSA-AES256-GCM-SHA384" (7) TLS-Session-Version = "TLS 1.2" (7) Sent Access-Challenge Id 69 from 10.165.11.10:1812 to 10.165.11.22:60615 length 0 (7) EAP-Message = 0x01ed004a1900170303003f1fae96bad6e00d48ce7ad2e1b929c90528c30fd32609c3c2118f3340a6907e96614b12ebc2b6ba149650d61a2c472a80075e0dd215e590cdfab2a14815e4be (7) Message-Authenticator = 0x00000000000000000000000000000000 (7) State = 0xce3ea9c4c8d3b0788bc56028040d79d2 (7) Finished request —— (9) Received Access-Request Id 71 from 10.165.11.22:60615 to 10.165.11.10:1812 length 294 (9) User-Name = "jack.carter" (9) NAS-IP-Address = 10.165.11.22 (9) NAS-Identifier = "f69fc26a572e" (9) Called-Station-Id = "F6-9F-C2-6A-57-2E:3 Kiln Lane" (9) NAS-Port-Type = Wireless-802.11 (9) Service-Type = Framed-User (9) Calling-Station-Id = "C4-C1-7D-A3-4A-9D" (9) Connect-Info = "CONNECT 0Mbps 802.11b" (9) Acct-Session-Id = "52716E330C1C872A" (9) Acct-Multi-Session-Id = "F0FA9E0972743E4E" (9) Mobility-Domain-Id = 20677 (9) WLAN-Pairwise-Cipher = 1027076 (9) WLAN-Group-Cipher = 1027076 (9) WLAN-AKM-Suite = 1027075 (9) WLAN-Group-Mgmt-Cipher = 1027078 (9) Filter-Id = "wpa-eap" (9) Framed-MTU = 1002 (9) EAP-Message = 0x02ee00251900170303001a3ec52a65400bea8d4fbc8b448ae8a913a68d895fc728d476d969 (9) State = 0xce3ea9c4c9d0b0788bc56028040d79d2 (9) Message-Authenticator = 0xf8240d1d2963814affbbbd133ac71376 (9) Restoring &session-state (9) &session-state:TLS-Session-Cipher-Suite = "ECDHE-ECDSA-AES256-GCM-SHA384" (9) &session-state:TLS-Session-Version = "TLS 1.2" (9) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (9) authorize { (9) policy filter_username { (9) if (&User-Name) { (9) if (&User-Name) -> TRUE (9) if (&User-Name) { (9) if (&User-Name =~ / /) { (9) if (&User-Name =~ / /) -> FALSE (9) if (&User-Name =~ /@[^@]*@/ ) { (9) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (9) if (&User-Name =~ /\.\./ ) { (9) if (&User-Name =~ /\.\./ ) -> FALSE (9) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) { (9) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE (9) if (&User-Name =~ /\.$/) { (9) if (&User-Name =~ /\.$/) -> FALSE (9) if (&User-Name =~ /@\./) { (9) if (&User-Name =~ /@\./) -> FALSE (9) } # if (&User-Name) = notfound (9) } # policy filter_username = notfound (9) [preprocess] = ok (9) [chap] = noop (9) [mschap] = noop (9) [digest] = noop (9) suffix: Checking for suffix after "@" (9) suffix: No '@' in User-Name = "jack.carter", looking up realm NULL (9) suffix: No such realm "NULL" (9) [suffix] = noop (9) eap: Peer sent EAP Response (code 2) ID 238 length 37 (9) eap: Continuing tunnel setup (9) [eap] = ok (9) } # authorize = ok (9) Found Auth-Type = eap (9) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (9) authenticate { (9) eap: Expiring EAP session with state 0x4944d27f48aac81c (9) eap: Finished EAP session with state 0xce3ea9c4c9d0b078 (9) eap: Previous EAP request found for state 0xce3ea9c4c9d0b078, released from the list (9) eap: Peer sent packet with method EAP PEAP (25) (9) eap: Calling submodule eap_peap to process data (9) eap_peap: Continuing EAP-TLS (9) eap_peap: [eaptls verify] = ok (9) eap_peap: Done initial handshake (9) eap_peap: [eaptls process] = ok (9) eap_peap: Session established. Decoding tunneled attributes (9) eap_peap: PEAP state phase2 (9) eap_peap: EAP method MSCHAPv2 (26) (9) eap_peap: Got tunneled request (9) eap_peap: EAP-Message = 0x02ee00061a03 (9) eap_peap: Setting User-Name to jack.carter (9) eap_peap: Sending tunneled request to inner-tunnel (9) eap_peap: EAP-Message = 0x02ee00061a03 (9) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1 (9) eap_peap: User-Name = "jack.carter" (9) eap_peap: State = 0x4944d27f48aac81c0486e93b4a708ee8 (9) Virtual server inner-tunnel received request (9) EAP-Message = 0x02ee00061a03 (9) FreeRADIUS-Proxied-To = 127.0.0.1 (9) User-Name = "jack.carter" (9) State = 0x4944d27f48aac81c0486e93b4a708ee8 (9) WARNING: Outer and inner identities are the same. User privacy is compromised. (9) server inner-tunnel { (9) session-state: No cached attributes (9) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/inner-tunnel (9) authorize { (9) policy filter_username { (9) if (&User-Name) { (9) if (&User-Name) -> TRUE (9) if (&User-Name) { (9) if (&User-Name =~ / /) { (9) if (&User-Name =~ / /) -> FALSE (9) if (&User-Name =~ /@[^@]*@/ ) { (9) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (9) if (&User-Name =~ /\.\./ ) { (9) if (&User-Name =~ /\.\./ ) -> FALSE (9) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) { (9) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE (9) if (&User-Name =~ /\.$/) { (9) if (&User-Name =~ /\.$/) -> FALSE (9) if (&User-Name =~ /@\./) { (9) if (&User-Name =~ /@\./) -> FALSE (9) } # if (&User-Name) = notfound (9) } # policy filter_username = notfound (9) [chap] = noop (9) [mschap] = noop (9) suffix: Checking for suffix after "@" (9) suffix: No '@' in User-Name = "jack.carter", looking up realm NULL (9) suffix: No such realm "NULL" (9) [suffix] = noop (9) update control { (9) &Proxy-To-Realm := LOCAL (9) } # update control = noop (9) eap: Peer sent EAP Response (code 2) ID 238 length 6 (9) eap: No EAP Start, assuming it's an on-going EAP conversation (9) [eap] = updated (9) files: users: Matched entry jack.carter at line 211 (9) [files] = ok (9) [expiration] = noop (9) [logintime] = noop (9) pap: Normalizing NT-Password from hex encoding, 32 bytes -> 16 bytes (9) pap: WARNING: Auth-Type already set. Not setting to PAP (9) [pap] = noop (9) } # authorize = updated (9) Found Auth-Type = eap (9) # Executing group from file /etc/freeradius/3.0/sites-enabled/inner-tunnel (9) authenticate { (9) eap: Expiring EAP session with state 0x4944d27f48aac81c (9) eap: Finished EAP session with state 0x4944d27f48aac81c (9) eap: Previous EAP request found for state 0x4944d27f48aac81c, released from the list (9) eap: Peer sent packet with method EAP MSCHAPv2 (26) (9) eap: Calling submodule eap_mschapv2 to process data (9) eap: Sending EAP Success (code 3) ID 238 length 4 (9) eap: Freeing handler (9) [eap] = ok (9) } # authenticate = ok (9) # Executing section post-auth from file /etc/freeradius/3.0/sites-enabled/inner-tunnel (9) post-auth { (9) if (1) { (9) if (1) -> TRUE (9) if (1) { (9) update reply { (9) User-Name !* ANY (9) Message-Authenticator !* ANY (9) EAP-Message !* ANY (9) Proxy-State !* ANY (9) MS-MPPE-Encryption-Types !* ANY (9) MS-MPPE-Encryption-Policy !* ANY (9) MS-MPPE-Send-Key !* ANY (9) MS-MPPE-Recv-Key !* ANY (9) } # update reply = noop (9) if (&control:UserGroup == "3KL") { (9) if (&control:UserGroup == "3KL") -> TRUE (9) if (&control:UserGroup == "3KL") { (9) update reply { (9) &Tunnel-Type := VLAN (9) &Tunnel-Medium-Type := IEEE-802 (9) &Tunnel-Private-Group-Id := "3" (9) } # update reply = noop (9) } # if (&control:UserGroup == "3KL") = noop (9) ... skipping elsif: Preceding "if" was taken (9) ... skipping else: Preceding "if" was taken (9) update { (9) &outer.session-state::Tunnel-Type += &reply:Tunnel-Type[*] -> VLAN (9) &outer.session-state::Tunnel-Medium-Type += &reply:Tunnel-Medium-Type[*] -> IEEE-802 (9) &outer.session-state::Tunnel-Private-Group-Id += &reply:Tunnel-Private-Group-Id[*] -> '3' (9) } # update = noop (9) } # if (1) = noop (9) } # post-auth = noop (9) } # server inner-tunnel (9) Virtual server sending reply (9) Tunnel-Type := VLAN (9) Tunnel-Medium-Type := IEEE-802 (9) Tunnel-Private-Group-Id := "3" (9) eap_peap: Got tunneled reply code 2 (9) eap_peap: Tunnel-Type := VLAN (9) eap_peap: Tunnel-Medium-Type := IEEE-802 (9) eap_peap: Tunnel-Private-Group-Id := "3" (9) eap_peap: Got tunneled reply RADIUS code 2 (9) eap_peap: Tunnel-Type := VLAN (9) eap_peap: Tunnel-Medium-Type := IEEE-802 (9) eap_peap: Tunnel-Private-Group-Id := "3" (9) eap_peap: Tunneled authentication was successful (9) eap_peap: SUCCESS (9) eap: Sending EAP Request (code 1) ID 239 length 46 (9) eap: EAP session adding &reply:State = 0xce3ea9c4c6d1b078 (9) [eap] = handled (9) } # authenticate = handled (9) Using Post-Auth-Type Challenge (9) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (9) Challenge { ... } # empty sub-section is ignored (9) session-state: Saving cached attributes (9) TLS-Session-Cipher-Suite = "ECDHE-ECDSA-AES256-GCM-SHA384" (9) TLS-Session-Version = "TLS 1.2" (9) Tunnel-Type += VLAN (9) Tunnel-Medium-Type += IEEE-802 (9) Tunnel-Private-Group-Id += "3" (9) Sent Access-Challenge Id 71 from 10.165.11.10:1812 to 10.165.11.22:60615 length 0 (9) EAP-Message = 0x01ef002e190017030300231fae96bad6e00d4ae741c0c47665f9e618130e7171a70aee2ff88f94beb21ce4054156 (9) Message-Authenticator = 0x00000000000000000000000000000000 (9) State = 0xce3ea9c4c6d1b0788bc56028040d79d2 (9) Finished request Waking up in 4.7 seconds. (10) Received Access-Request Id 72 from 10.165.11.22:60615 to 10.165.11.10:1812 length 303 (10) User-Name = "jack.carter" (10) NAS-IP-Address = 10.165.11.22 (10) NAS-Identifier = "f69fc26a572e" (10) Called-Station-Id = "F6-9F-C2-6A-57-2E:3 Kiln Lane" (10) NAS-Port-Type = Wireless-802.11 (10) Service-Type = Framed-User (10) Calling-Station-Id = "C4-C1-7D-A3-4A-9D" (10) Connect-Info = "CONNECT 0Mbps 802.11b" (10) Acct-Session-Id = "52716E330C1C872A" (10) Acct-Multi-Session-Id = "F0FA9E0972743E4E" (10) Mobility-Domain-Id = 20677 (10) WLAN-Pairwise-Cipher = 1027076 (10) WLAN-Group-Cipher = 1027076 (10) WLAN-AKM-Suite = 1027075 (10) WLAN-Group-Mgmt-Cipher = 1027078 (10) Filter-Id = "wpa-eap" (10) Framed-MTU = 1002 (10) EAP-Message = 0x02ef002e190017030300233ec52a65400bea8e440ad4e481478c0257205e3eaa7c1b023bc1087cbb415619b99cc3 (10) State = 0xce3ea9c4c6d1b0788bc56028040d79d2 (10) Message-Authenticator = 0x6d81dd1c99540ca93495b6301b6327b8 (10) Restoring &session-state (10) &session-state:TLS-Session-Cipher-Suite = "ECDHE-ECDSA-AES256-GCM-SHA384" (10) &session-state:TLS-Session-Version = "TLS 1.2" (10) &session-state:Tunnel-Type += VLAN (10) &session-state:Tunnel-Medium-Type += IEEE-802 (10) &session-state:Tunnel-Private-Group-Id += "3" (10) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (10) authorize { (10) policy filter_username { (10) if (&User-Name) { (10) if (&User-Name) -> TRUE (10) if (&User-Name) { (10) if (&User-Name =~ / /) { (10) if (&User-Name =~ / /) -> FALSE (10) if (&User-Name =~ /@[^@]*@/ ) { (10) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (10) if (&User-Name =~ /\.\./ ) { (10) if (&User-Name =~ /\.\./ ) -> FALSE (10) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) { (10) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE (10) if (&User-Name =~ /\.$/) { (10) if (&User-Name =~ /\.$/) -> FALSE (10) if (&User-Name =~ /@\./) { (10) if (&User-Name =~ /@\./) -> FALSE (10) } # if (&User-Name) = notfound (10) } # policy filter_username = notfound (10) [preprocess] = ok (10) [chap] = noop (10) [mschap] = noop (10) [digest] = noop (10) suffix: Checking for suffix after "@" (10) suffix: No '@' in User-Name = "jack.carter", looking up realm NULL (10) suffix: No such realm "NULL" (10) [suffix] = noop (10) eap: Peer sent EAP Response (code 2) ID 239 length 46 (10) eap: Continuing tunnel setup (10) [eap] = ok (10) } # authorize = ok (10) Found Auth-Type = eap (10) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (10) authenticate { (10) eap: Expiring EAP session with state 0xce3ea9c4c6d1b078 (10) eap: Finished EAP session with state 0xce3ea9c4c6d1b078 (10) eap: Previous EAP request found for state 0xce3ea9c4c6d1b078, released from the list (10) eap: Peer sent packet with method EAP PEAP (25) (10) eap: Calling submodule eap_peap to process data (10) eap_peap: Continuing EAP-TLS (10) eap_peap: [eaptls verify] = ok (10) eap_peap: Done initial handshake (10) eap_peap: [eaptls process] = ok (10) eap_peap: Session established. Decoding tunneled attributes (10) eap_peap: PEAP state send tlv success (10) eap_peap: Received EAP-TLV response (10) eap_peap: Success (10) eap_peap: No information to cache: session caching will be disabled for session fde03729712b1736de0ff733e84c1db062aa9305e46565842e1afdb4f851df61 (10) eap: Sending EAP Success (code 3) ID 239 length 4 (10) eap: Freeing handler (10) [eap] = ok (10) } # authenticate = ok (10) # Executing section post-auth from file /etc/freeradius/3.0/sites-enabled/default (10) post-auth { (10) if (session-state:User-Name && reply:User-Name && request:User-Name && (reply:User-Name == request:User-Name)) { (10) if (session-state:User-Name && reply:User-Name && request:User-Name && (reply:User-Name == request:User-Name)) -> FALSE (10) update { (10) &reply::TLS-Session-Cipher-Suite += &session-state:TLS-Session-Cipher-Suite[*] -> 'ECDHE-ECDSA-AES256-GCM-SHA384' (10) &reply::TLS-Session-Version += &session-state:TLS-Session-Version[*] -> 'TLS 1.2' (10) &reply::Tunnel-Type += &session-state:Tunnel-Type[*] -> VLAN (10) &reply::Tunnel-Medium-Type += &session-state:Tunnel-Medium-Type[*] -> IEEE-802 (10) &reply::Tunnel-Private-Group-Id += &session-state:Tunnel-Private-Group-Id[*] -> '3' (10) } # update = noop (10) [exec] = noop (10) policy remove_reply_message_if_eap { (10) if (&reply:EAP-Message && &reply:Reply-Message) { (10) if (&reply:EAP-Message && &reply:Reply-Message) -> FALSE (10) else { (10) [noop] = noop (10) } # else = noop (10) } # policy remove_reply_message_if_eap = noop (10) } # post-auth = noop (10) Sent Access-Accept Id 72 from 10.165.11.10:1812 to 10.165.11.22:60615 length 0 (10) MS-MPPE-Recv-Key = 0x5bc678f0622afa2f329c442f5e58b7fb3dcd0215fbb5ed423f71b9678acc5f2f (10) MS-MPPE-Send-Key = 0xaca7502a2c2210d5bde3adceef15bd3d3a08fe6fbdc1b19cd94f270a6ef5d7a4 (10) EAP-Message = 0x03ef0004 (10) Message-Authenticator = 0x00000000000000000000000000000000 (10) User-Name = "jack.carter" (10) Tunnel-Type += VLAN (10) Tunnel-Medium-Type += IEEE-802 (10) Tunnel-Private-Group-Id += "3" (10) Finished request

Thanks for following up Alan… I have since updated the Apple configuration profiles I use on devices so the inner and outer identity is different and that warning has gone. Thanks again for your help and apologies for the initial hopeless reports. Jack On 21 Apr 2024, at 13:29, Alan DeKok <aland@deployingradius.com> wrote: On Apr 16, 2024, at 7:08 AM, Jack Carter <jack_carter94@hotmail.com> wrote:

(7)(8)(9) WARNING: Outer and inner identities are the same. User privacy is compromised.

It's a warning. You're free to ignore it, or fix it.

(8)(9) pap: WARNING: Auth-Type already set. Not setting to PAP

That's another warning. It's fine.

I’m assuming the pap warning is more of an FYI as i’m using eap so can be ignored? How can I resolve the outer and inner identities being the same?

The identities warning comes about because you configured the supplicant to send the same inner and outer identity. If you want to fix that, you can't fix it on the FreeRADIUS side. Alan DeKok. - List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html