WIMAX problem

[Dimitris Theofilatos]

How can i configure these attributes? The only information i found about 
WIMAX is that i have to
type "wimax" at the post-auth section.
 
>> I downloaded the last stable version via "git".
>> I typed the command git clone
>> git://git.freeradius.org/freeradius-server.git radiusd. Is that correct?
>>
>> Then i installed freeradius and run radiusd but the same log of radiusd
>> appeared. The log is at the attachment.
>>
>>     
>
> rad_recv: Access-Request packet from host 192.168.10.3 port 1812, id=2,
> length=314
>         User-Name = "{am=1}anonymous at wintegra.com"
>         EAP-Message =
> 0x0202007015800000006616030100610100005d030149502abe282b6324c07315e57a95bd7f42dd38d221a592206f35256651f0c31e00003600390038003500160013000a00330032002f0007006600050004006300620061001500120009006500640060001400110008000600030100
>         Message-Authenticator = 0xe0ef04d2f20e8b07aeec51fef34cb796
>         NAS-IP-Address = 192.168.10.3
>         NAS-Port-Type = 27
>         Calling-Station-Id = "\000!\000\r\302#"
>         Chargeable-User-Identity = ""
>         WiMAX-Release = "1.0"
>         WiMAX-Accounting-Capabilities = IP-Session-Based
>         WiMAX-Hotlining-Capabilities = Not-Supported
>         WiMAX-Idle-Mode-Notification-Cap = Supported
>         WiMAX-Available-In-Client = 3
>         WiMAX-Session-Termination-Capability = Dynamic-Authorization
>         WiMAX-GMT-Timezone-offset = 0
>         WiMAX-BS-Id = 0x0050c21174a4
>         Service-Type = Framed-User
>         Framed-MTU = 2000
>         State = 0xc8679e10c8658b965d7f92904f2ccae1
> ..
> [wimax] WARNING: WiMAX-MN-NAI was not found in the request or in the
> reply.
> [wimax] WARNING: We cannot calculate MN-HA keys.
> [wimax] WARNING: WiMAX-IP-Technology not found in reply.
> [wimax] WARNING: Not calculating MN-HA keys
> ++[wimax] returns updated
> Sending Access-Accept of id 7 to 192.168.10.3 port 1812
>         MS-MPPE-Recv-Key =
> 0x0b807e1db02ccb8eabde63e0d4f7558f80c50fc6c46bf30f0697a8169a279608
>         MS-MPPE-Send-Key =
> 0x52964f865d141e239c4ef6e8528c3b33c0b3db0c78c7eeee565c07563c161c21
>         EAP-Message = 0x03070004
>         Message-Authenticator = 0x00000000000000000000000000000000
>         User-Name = "{am=1}anonymous at wintegra.com"
>
> So the message is correct! You haven't configured these attributes as
> per instructions in wimax module.
>
> Ivan Kalik
> Kalik Informatika ISP
>
> -
> List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
>
>
>   

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.freeradius.org/pipermail/freeradius-users/attachments/20081222/4e89b3ab/attachment.html>