User get after few minute

[Sokphak TOUCH]

Dear All,

I have issue with configure radius. I have one Juniper MX80 for doing as
LNS in my lab and FreeRADIUS Version 2.1.12 installed. I can see there is
successful connected log to radius but after around 1mn it connect again
and again. I have check in MX80 but has no any significant log.
Below is the full log in debug mode of radius during connect. Please advice

rad_recv: Access-Request packet from host 22.0.0.77 port 51280, id=32,
length=237
        User-Name = "testuser at intel.com"
        Service-Type = Framed-User
        CHAP-Password = 0x6424072271437b7df6f638bd05496fe856
        CHAP-Challenge =
0xcf44cbf713aedaac40824ffc535532d96e7b109b025cb2a3b0
        Chargeable-User-Identity = ""
        Acct-Session-Id = "491"
        ERX-Dhcp-Mac-Addr = "0000.0000.0000"
        NAS-Identifier = "MX80-LAB-LNS"
        NAS-Port = 4095
        NAS-Port-Id = "Ip:192.168.77.1:192
.168.77.2:55776:38107:10971:4534:2765160448"
        NAS-Port-Type = Virtual
        ERX-Attr-162 = 0x05f5e1
        ERX-Attr-163 = 0x05f5e1
        NAS-IP-Address = 22.0.0.77
# Executing section authorize from file /etc/raddb/sites-enabled/default
+- entering group authorize {...}
++[preprocess] returns ok
[chap] Setting 'Auth-Type := CHAP'
++[chap] returns ok
++[mschap] returns noop
++[digest] returns noop
[suffix] Looking up realm "eintel.com" for User-Name = "testuser at intel.com"
[suffix] No such realm "eintel.com"
++[suffix] returns noop
[eap] No EAP-Message, not doing EAP
++[eap] returns noop
++[files] returns noop
[sql]   expand: %{User-Name} -> testuser at intel.com
[sql] sql_set_user escaped user --> 'testuser at intel.com'
rlm_sql (sql): Reserving sql socket id: 4
[sql]   expand: SELECT id, username, attribute, value, op           FROM
radcheck           WHERE username = '%{SQL-User-Name}'           ORDER BY
id -> SELECT id, username, attribute, value, op           FROM
radcheck           WHERE username = 'testuser at intel.com'           ORDER BY
id
[sql] User found in radcheck table
[sql]   expand: SELECT id, username, attribute, value, op           FROM
radreply           WHERE username = '%{SQL-User-Name}'           ORDER BY
id -> SELECT id, username, attribute, value, op           FROM
radreply           WHERE username = 'testuser at intel.com'           ORDER BY
id
[sql]   expand: SELECT groupname           FROM radusergroup
WHERE username = '%{SQL-User-Name}'           ORDER BY priority -> SELECT
groupname           FROM radusergroup           WHERE username = '
testuser at intel.com'           ORDER BY priority
rlm_sql (sql): Released sql socket id: 4
++[sql] returns ok
++[expiration] returns noop
++[logintime] returns noop
[pap] WARNING: Auth-Type already set.  Not setting to PAP
++[pap] returns noop
Found Auth-Type = CHAP
# Executing group from file /etc/raddb/sites-enabled/default
+- entering group CHAP {...}
[chap] login attempt by "testuser at intel.com" with CHAP password
[chap] Using clear text password "saba" for user
testuser at intel.comauthentication.
[chap] chap user testuser at intel.com authenticated succesfully
++[chap] returns ok
# Executing section post-auth from file /etc/raddb/sites-enabled/default
+- entering group post-auth {...}
[sql]   expand: %{User-Name} -> testuser at intel.com
[sql] sql_set_user escaped user --> 'testuser at intel.com'
[sql]   expand: %{User-Password} ->
[sql]   ... expanding second conditional
[sql]   expand: %{Chap-Password} -> 0x6424072271437b7df6f638bd05496fe856
[sql]   expand: INSERT INTO radpostauth
(username, pass, reply, authdate)                           VALUES
(                           '%{User-Name}',
'%{%{User-Password}:-%{Chap-Password}}',
'%{reply:Packet-Type}', '%S') -> INSERT INTO
radpostauth                           (username, pass, reply,
authdate)                           VALUES (                           '
testuser at intel.com',
'0x6424072271437b7df6f638bd05496fe856',
'Access-Accept', '2013-08-22 15:51:05')
rlm_sql (sql) in sql_postauth: query is INSERT INTO
radpostauth                           (username, pass, reply,
authdate)                           VALUES (                           '
testuser at intel.com',
'0x6424072271437b7df6f638bd05496fe856',
'Access-Accept', '2013-08-22 15:51:05')
rlm_sql (sql): Reserving sql socket id: 3
rlm_sql (sql): Released sql socket id: 3
++[sql] returns ok
++[exec] returns noop
Sending Access-Accept of id 32 to 22.0.0.77 port 51280
        Framed-IP-Address = 10.1.1.123
Finished request 2.
Going to the next request
Waking up in 4.9 seconds.
Cleaning up request 2 ID 32 with timestamp +177
Ready to process requests.

Regards,
SP
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.freeradius.org/pipermail/freeradius-users/attachments/20130822/6e54bae5/attachment-0001.html>