Freeradius 3.0.17 EAP-TLS Authentication with LDAP Authorization

Kevin Virk Kevin.Virk at faithlife.com
Tue Aug 21 21:29:55 CEST 2018


Hello all I have followed previous advice given to me and upgraded my install to FreeRADIUS 3.0.17 . I am trying to achieve a setup where computers are let onto company internet via eap-tls and then are separated into VLANS with ldap after this. Currently I believe I have eap-tls working as my eapol test has been successful. However after adding in the ldap module I am getting a bind error which I know is an LDAP error and not a freeradius one. I was hoping someone here could take a look at my debug info and see if I have overlooked anything. Thank you in advance for the help. I also refrenced this previous thread to help out with some of the configs http://freeradius.1045715.n5.nabble.com/Freeradius-3-x-with-LDAP-authentication-td5746729.html.

FreeRADIUS Version 3.0.17
Copyright (C) 1999-2017 The FreeRADIUS server project and contributors
There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A
PARTICULAR PURPOSE
You may redistribute copies of FreeRADIUS under the terms of the
GNU General Public License
For more information about these matters, see the file named COPYRIGHT
Starting - reading configuration files ...
including dictionary file /usr/local/share/freeradius/dictionary
including dictionary file /usr/local/share/freeradius/dictionary.dhcp
including dictionary file /usr/local/share/freeradius/dictionary.vqp
including dictionary file /usr/local/etc/raddb/dictionary
including configuration file /usr/local/etc/raddb/radiusd.conf
including configuration file /usr/local/etc/raddb/proxy.conf
including configuration file /usr/local/etc/raddb/clients.conf
including files in directory /usr/local/etc/raddb/mods-enabled/
including configuration file /usr/local/etc/raddb/mods-enabled/detail
including configuration file /usr/local/etc/raddb/mods-enabled/files
including configuration file /usr/local/etc/raddb/mods-enabled/cache_eap
including configuration file /usr/local/etc/raddb/mods-enabled/mschap
including configuration file /usr/local/etc/raddb/mods-enabled/realm
including configuration file /usr/local/etc/raddb/mods-enabled/utf8
including configuration file /usr/local/etc/raddb/mods-enabled/attr_filter
including configuration file /usr/local/etc/raddb/mods-enabled/dynamic_clients
including configuration file /usr/local/etc/raddb/mods-enabled/digest
including configuration file /usr/local/etc/raddb/mods-enabled/ntlm_auth
including configuration file /usr/local/etc/raddb/mods-enabled/radutmp
including configuration file /usr/local/etc/raddb/mods-enabled/echo
including configuration file /usr/local/etc/raddb/mods-enabled/linelog
including configuration file /usr/local/etc/raddb/mods-enabled/eap
including configuration file /usr/local/etc/raddb/mods-enabled/pap
including configuration file /usr/local/etc/raddb/mods-enabled/unpack
including configuration file /usr/local/etc/raddb/mods-enabled/detail.log
including configuration file /usr/local/etc/raddb/mods-enabled/exec
including configuration file /usr/local/etc/raddb/mods-enabled/unix
including configuration file /usr/local/etc/raddb/mods-enabled/logintime
including configuration file /usr/local/etc/raddb/mods-enabled/sradutmp
including configuration file /usr/local/etc/raddb/mods-enabled/chap
including configuration file /usr/local/etc/raddb/mods-enabled/soh
including configuration file /usr/local/etc/raddb/mods-enabled/date
including configuration file /usr/local/etc/raddb/mods-enabled/always
including configuration file /usr/local/etc/raddb/mods-enabled/preprocess
including configuration file /usr/local/etc/raddb/mods-enabled/expr
including configuration file /usr/local/etc/raddb/mods-enabled/replicate
including configuration file /usr/local/etc/raddb/mods-enabled/ldap
including configuration file /usr/local/etc/raddb/mods-enabled/expiration
including configuration file /usr/local/etc/raddb/mods-enabled/passwd
including files in directory /usr/local/etc/raddb/policy.d/
including configuration file /usr/local/etc/raddb/policy.d/cui
including configuration file /usr/local/etc/raddb/policy.d/accounting
including configuration file /usr/local/etc/raddb/policy.d/abfab-tr
including configuration file /usr/local/etc/raddb/policy.d/control
including configuration file /usr/local/etc/raddb/policy.d/dhcp
including configuration file /usr/local/etc/raddb/policy.d/eap
including configuration file /usr/local/etc/raddb/policy.d/operator-name
including configuration file /usr/local/etc/raddb/policy.d/canonicalization
including configuration file /usr/local/etc/raddb/policy.d/debug
including configuration file /usr/local/etc/raddb/policy.d/filter
including configuration file /usr/local/etc/raddb/policy.d/moonshot-targeted-ids
including files in directory /usr/local/etc/raddb/sites-enabled/
including configuration file /usr/local/etc/raddb/sites-enabled/inner-tunnel
including configuration file /usr/local/etc/raddb/sites-enabled/default
main {
 security {
        allow_core_dumps = no
 }
        name = "radiusd"
        prefix = "/usr/local"
        localstatedir = "/usr/local/var"
        logdir = "/usr/local/var/log/radius"
        run_dir = "/usr/local/var/run/radiusd"
}
main {
        name = "radiusd"
        prefix = "/usr/local"
        localstatedir = "/usr/local/var"
        sbindir = "/usr/local/sbin"
        logdir = "/usr/local/var/log/radius"
        run_dir = "/usr/local/var/run/radiusd"
        libdir = "/usr/local/lib"
        radacctdir = "/usr/local/var/log/radius/radacct"
        hostname_lookups = no
        max_request_time = 30
        cleanup_delay = 5
        max_requests = 16384
        pidfile = "/usr/local/var/run/radiusd/radiusd.pid"
        checkrad = "/usr/local/sbin/checkrad"
        debug_level = 0
        proxy_requests = yes
 log {
        stripped_names = no
        auth = no
        auth_badpass = no
        auth_goodpass = no
        colourise = yes
        msg_denied = "You are already logged in - access denied"
 }
 resources {
 }
 security {
        max_attributes = 200
        reject_delay = 1.000000
        status_server = yes
        allow_vulnerable_openssl = "yes"
 }
}
radiusd: #### Loading Realms and Home Servers ####
 proxy server {
        retry_delay = 5
        retry_count = 3
        default_fallback = no
        dead_time = 120
        wake_all_if_all_dead = no
 }
 home_server localhost {
        ipaddr = 127.0.0.1
        port = 1812
        type = "auth"
        secret = <<< secret >>>
        response_window = 20.000000
        response_timeouts = 1
        max_outstanding = 65536
        zombie_period = 40
        status_check = "status-server"
        ping_interval = 30
        check_interval = 30
        check_timeout = 4
        num_answers_to_alive = 3
        revive_interval = 120
  limit {
        max_connections = 16
        max_requests = 0
        lifetime = 0
        idle_timeout = 0
  }
  coa {
        irt = 2
        mrt = 16
        mrc = 5
        mrd = 30
  }
 }
 home_server_pool my_auth_failover {
        type = fail-over
        home_server = localhost
 }
 realm example.com {
        auth_pool = my_auth_failover
 }
 realm LOCAL {
 }
radiusd: #### Loading Clients ####
 client kevintest {
        ipaddr = 172.17.17.227
        require_message_authenticator = no
        secret = <<< secret >>>
  limit {
        max_connections = 16
        lifetime = 0
        idle_timeout = 30
  }
 }
 client localhost {
        ipaddr = 127.0.0.1
        require_message_authenticator = no
        secret = <<< secret >>>
        nas_type = "other"
        proto = "*"
  limit {
        max_connections = 16
        lifetime = 0
        idle_timeout = 30
  }
 }
 client localhost_ipv6 {
        ipv6addr = ::1
        require_message_authenticator = no
        secret = <<< secret >>>
  limit {
        max_connections = 16
        lifetime = 0
        idle_timeout = 30
  }
 }
Debugger not attached
 # Creating Auth-Type = ntlm_auth
 # Creating Auth-Type = mschap
 # Creating Auth-Type = eap
 # Creating Auth-Type = PAP
 # Creating Auth-Type = CHAP
 # Creating Auth-Type = MS-CHAP
radiusd: #### Instantiating modules ####
 modules {
  # Loaded module rlm_detail
  # Loading module "detail" from file /usr/local/etc/raddb/mods-enabled/detail
  detail {
        filename = "/usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/detail-%Y%m%d"
        header = "%t"
        permissions = 384
        locking = no
        escape_filenames = no
        log_packet_header = no
  }
  # Loaded module rlm_files
  # Loading module "files" from file /usr/local/etc/raddb/mods-enabled/files
  files {
        filename = "/usr/local/etc/raddb/mods-config/files/authorize"
        acctusersfile = "/usr/local/etc/raddb/mods-config/files/accounting"
        preproxy_usersfile = "/usr/local/etc/raddb/mods-config/files/pre-proxy"
  }
  # Loaded module rlm_cache
  # Loading module "cache_eap" from file /usr/local/etc/raddb/mods-enabled/cache_eap
  cache cache_eap {
        driver = "rlm_cache_rbtree"
        key = "%{%{control:State}:-%{%{reply:State}:-%{State}}}"
        ttl = 15
        max_entries = 0
        epoch = 0
        add_stats = no
  }
  # Loaded module rlm_mschap
  # Loading module "mschap" from file /usr/local/etc/raddb/mods-enabled/mschap
  mschap {
        use_mppe = yes
        require_encryption = no
        require_strong = no
        with_ntdomain_hack = yes
   passchange {
   }
        allow_retry = yes
        winbind_retry_with_normalised_username = no
  }
  # Loaded module rlm_realm
  # Loading module "IPASS" from file /usr/local/etc/raddb/mods-enabled/realm
  realm IPASS {
        format = "prefix"
        delimiter = "/"
        ignore_default = no
        ignore_null = no
  }
  # Loading module "suffix" from file /usr/local/etc/raddb/mods-enabled/realm
  realm suffix {
        format = "suffix"
        delimiter = "@"
        ignore_default = no
        ignore_null = no
  }
  # Loading module "realmpercent" from file /usr/local/etc/raddb/mods-enabled/realm
  realm realmpercent {
        format = "suffix"
        delimiter = "%"
        ignore_default = no
        ignore_null = no
  }
  # Loading module "ntdomain" from file /usr/local/etc/raddb/mods-enabled/realm
  realm ntdomain {
        format = "prefix"
        delimiter = "\\"
        ignore_default = no
        ignore_null = no
  }
  # Loaded module rlm_utf8
  # Loading module "utf8" from file /usr/local/etc/raddb/mods-enabled/utf8
  # Loaded module rlm_attr_filter
  # Loading module "attr_filter.post-proxy" from file /usr/local/etc/raddb/mods-enabled/attr_filter
  attr_filter attr_filter.post-proxy {
        filename = "/usr/local/etc/raddb/mods-config/attr_filter/post-proxy"
        key = "%{Realm}"
        relaxed = no
  }
  # Loading module "attr_filter.pre-proxy" from file /usr/local/etc/raddb/mods-enabled/attr_filter
  attr_filter attr_filter.pre-proxy {
        filename = "/usr/local/etc/raddb/mods-config/attr_filter/pre-proxy"
        key = "%{Realm}"
        relaxed = no
  }
  # Loading module "attr_filter.access_reject" from file /usr/local/etc/raddb/mods-enabled/attr_filter
  attr_filter attr_filter.access_reject {
        filename = "/usr/local/etc/raddb/mods-config/attr_filter/access_reject"
        key = "%{User-Name}"
        relaxed = no
  }
  # Loading module "attr_filter.access_challenge" from file /usr/local/etc/raddb/mods-enabled/attr_filter
  attr_filter attr_filter.access_challenge {
        filename = "/usr/local/etc/raddb/mods-config/attr_filter/access_challenge"
        key = "%{User-Name}"
        relaxed = no
  }
  # Loading module "attr_filter.accounting_response" from file /usr/local/etc/raddb/mods-enabled/attr_filter
  attr_filter attr_filter.accounting_response {
        filename = "/usr/local/etc/raddb/mods-config/attr_filter/accounting_response"
        key = "%{User-Name}"
        relaxed = no
  }
  # Loaded module rlm_dynamic_clients
  # Loading module "dynamic_clients" from file /usr/local/etc/raddb/mods-enabled/dynamic_clients
  # Loaded module rlm_digest
  # Loading module "digest" from file /usr/local/etc/raddb/mods-enabled/digest
  # Loaded module rlm_exec
  # Loading module "ntlm_auth" from file /usr/local/etc/raddb/mods-enabled/ntlm_auth
  exec ntlm_auth {
        wait = yes
        program = "/usr/bin/ntlm_auth --request-nt-key --domain=DOMAIN.net --username=%{mschap:User-Name} --password=%{User-Password}"
        shell_escape = yes
  }
  # Loaded module rlm_radutmp
  # Loading module "radutmp" from file /usr/local/etc/raddb/mods-enabled/radutmp
  radutmp {
        filename = "/usr/local/var/log/radius/radutmp"
        username = "%{User-Name}"
        case_sensitive = yes
        check_with_nas = yes
        permissions = 384
        caller_id = yes
  }
  # Loading module "echo" from file /usr/local/etc/raddb/mods-enabled/echo
  exec echo {
        wait = yes
        program = "/bin/echo %{User-Name}"
        input_pairs = "request"
        output_pairs = "reply"
        shell_escape = yes
  }
  # Loaded module rlm_linelog
  # Loading module "linelog" from file /usr/local/etc/raddb/mods-enabled/linelog
  linelog {
        filename = "/usr/local/var/log/radius/linelog"
        escape_filenames = no
        syslog_severity = "info"
        permissions = 384
        format = "This is a log message for %{User-Name}"
        reference = "messages.%{%{reply:Packet-Type}:-default}"
  }
  # Loading module "log_accounting" from file /usr/local/etc/raddb/mods-enabled/linelog
  linelog log_accounting {
        filename = "/usr/local/var/log/radius/linelog-accounting"
        escape_filenames = no
        syslog_severity = "info"
        permissions = 384
        format = ""
        reference = "Accounting-Request.%{%{Acct-Status-Type}:-unknown}"
  }
  # Loaded module rlm_eap
  # Loading module "eap" from file /usr/local/etc/raddb/mods-enabled/eap
  eap {
        default_eap_type = "tls"
        timer_expire = 60
        ignore_unknown_eap_types = no
        cisco_accounting_username_bug = no
        max_sessions = 16384
  }
  # Loaded module rlm_pap
  # Loading module "pap" from file /usr/local/etc/raddb/mods-enabled/pap
  pap {
        normalise = yes
  }
  # Loaded module rlm_unpack
  # Loading module "unpack" from file /usr/local/etc/raddb/mods-enabled/unpack
  # Loading module "auth_log" from file /usr/local/etc/raddb/mods-enabled/detail.log
  detail auth_log {
        filename = "/usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d"
        header = "%t"
        permissions = 384
        locking = no
        escape_filenames = no
        log_packet_header = no
  }
  # Loading module "reply_log" from file /usr/local/etc/raddb/mods-enabled/detail.log
  detail reply_log {
        filename = "/usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/reply-detail-%Y%m%d"
        header = "%t"
        permissions = 384
        locking = no
        escape_filenames = no
        log_packet_header = no
  }
  # Loading module "pre_proxy_log" from file /usr/local/etc/raddb/mods-enabled/detail.log
  detail pre_proxy_log {
        filename = "/usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/pre-proxy-detail-%Y%m%d"
        header = "%t"
        permissions = 384
        locking = no
        escape_filenames = no
        log_packet_header = no
  }
  # Loading module "post_proxy_log" from file /usr/local/etc/raddb/mods-enabled/detail.log
  detail post_proxy_log {
        filename = "/usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/post-proxy-detail-%Y%m%d"
        header = "%t"
        permissions = 384
        locking = no
        escape_filenames = no
        log_packet_header = no
  }
  # Loading module "exec" from file /usr/local/etc/raddb/mods-enabled/exec
  exec {
        wait = no
        input_pairs = "request"
        shell_escape = yes
        timeout = 10
  }
  # Loaded module rlm_unix
  # Loading module "unix" from file /usr/local/etc/raddb/mods-enabled/unix
  unix {
        radwtmp = "/usr/local/var/log/radius/radwtmp"
  }
Creating attribute Unix-Group
  # Loaded module rlm_logintime
  # Loading module "logintime" from file /usr/local/etc/raddb/mods-enabled/logintime
  logintime {
        minimum_timeout = 60
  }
  # Loading module "sradutmp" from file /usr/local/etc/raddb/mods-enabled/sradutmp
  radutmp sradutmp {
        filename = "/usr/local/var/log/radius/sradutmp"
        username = "%{User-Name}"
        case_sensitive = yes
        check_with_nas = yes
        permissions = 420
        caller_id = no
  }
  # Loaded module rlm_chap
  # Loading module "chap" from file /usr/local/etc/raddb/mods-enabled/chap
  # Loaded module rlm_soh
  # Loading module "soh" from file /usr/local/etc/raddb/mods-enabled/soh
  soh {
        dhcp = yes
  }
  # Loaded module rlm_date
  # Loading module "date" from file /usr/local/etc/raddb/mods-enabled/date
  date {
        format = "%b %e %Y %H:%M:%S %Z"
        utc = no
  }
  # Loaded module rlm_always
  # Loading module "reject" from file /usr/local/etc/raddb/mods-enabled/always
  always reject {
        rcode = "reject"
        simulcount = 0
        mpp = no
  }
  # Loading module "fail" from file /usr/local/etc/raddb/mods-enabled/always
  always fail {
        rcode = "fail"
        simulcount = 0
        mpp = no
  }
  # Loading module "ok" from file /usr/local/etc/raddb/mods-enabled/always
  always ok {
        rcode = "ok"
        simulcount = 0
        mpp = no
  }
  # Loading module "handled" from file /usr/local/etc/raddb/mods-enabled/always
  always handled {
        rcode = "handled"
        simulcount = 0
        mpp = no
  }
  # Loading module "invalid" from file /usr/local/etc/raddb/mods-enabled/always
  always invalid {
        rcode = "invalid"
        simulcount = 0
        mpp = no
  }
  # Loading module "userlock" from file /usr/local/etc/raddb/mods-enabled/always
  always userlock {
        rcode = "userlock"
        simulcount = 0
        mpp = no
  }
  # Loading module "notfound" from file /usr/local/etc/raddb/mods-enabled/always
  always notfound {
        rcode = "notfound"
        simulcount = 0
        mpp = no
  }
  # Loading module "noop" from file /usr/local/etc/raddb/mods-enabled/always
  always noop {
        rcode = "noop"
        simulcount = 0
        mpp = no
  }
  # Loading module "updated" from file /usr/local/etc/raddb/mods-enabled/always
  always updated {
        rcode = "updated"
        simulcount = 0
        mpp = no
  }
  # Loaded module rlm_preprocess
  # Loading module "preprocess" from file /usr/local/etc/raddb/mods-enabled/preprocess
  preprocess {
        huntgroups = "/usr/local/etc/raddb/mods-config/preprocess/huntgroups"
        hints = "/usr/local/etc/raddb/mods-config/preprocess/hints"
        with_ascend_hack = no
        ascend_channels_per_line = 23
        with_ntdomain_hack = no
        with_specialix_jetstream_hack = no
        with_cisco_vsa_hack = no
        with_alvarion_vsa_hack = no
  }
  # Loaded module rlm_expr
  # Loading module "expr" from file /usr/local/etc/raddb/mods-enabled/expr
  expr {
        safe_characters = "@abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789.-_: /äéöüàâæçèéêëîïôœùûüaÿÄÉÖÜßÀÂÆÇÈÉÊËÎÏÔŒÙÛÜŸ"
  }
  # Loaded module rlm_replicate
  # Loading module "replicate" from file /usr/local/etc/raddb/mods-enabled/replicate
  # Loaded module rlm_ldap
  # Loading module "ldap" from file /usr/local/etc/raddb/mods-enabled/ldap
  ldap {
        server = "Domain.net"
        identity = "cn=ldap.query,ou=service.accounts,ou=Users,ou=operations,ou=departments,dc=Domain,dc=net"
        password = <<< secret >>>
   sasl {
   }
   user {
        scope = "sub"
        access_positive = yes
    sasl {
    }
   }
   group {
        filter = "(objectClass=posixGroup)"
        scope = "sub"
        name_attribute = "cn"
        membership_attribute = "memberOf"
        cacheable_name = no
        cacheable_dn = no
   }
   client {
        filter = "(objectClass=radiusClient)"
        scope = "sub"
        base_dn = "dc=Domain,dc=net"
   }
   profile {
   }
   options {
        ldap_debug = 40
        chase_referrals = yes
        rebind = yes
        net_timeout = 1
        res_timeout = 10
        srv_timelimit = 3
        idle = 60
        probes = 3
        interval = 3
   }
   tls {
        start_tls = no
   }
  }
Creating attribute LDAP-Group
  # Loaded module rlm_expiration
  # Loading module "expiration" from file /usr/local/etc/raddb/mods-enabled/expiration
  # Loaded module rlm_passwd
  # Loading module "etc_passwd" from file /usr/local/etc/raddb/mods-enabled/passwd
  passwd etc_passwd {
        filename = "/etc/passwd"
        format = "*User-Name:Crypt-Password:"
        delimiter = ":"
        ignore_nislike = no
        ignore_empty = yes
        allow_multiple_keys = no
        hash_size = 100
  }
  instantiate {
  }
  # Instantiating module "detail" from file /usr/local/etc/raddb/mods-enabled/detail
  # Instantiating module "files" from file /usr/local/etc/raddb/mods-enabled/files
reading pairlist file /usr/local/etc/raddb/mods-config/files/authorize
reading pairlist file /usr/local/etc/raddb/mods-config/files/accounting
reading pairlist file /usr/local/etc/raddb/mods-config/files/pre-proxy
  # Instantiating module "cache_eap" from file /usr/local/etc/raddb/mods-enabled/cache_eap
rlm_cache (cache_eap): Driver rlm_cache_rbtree (module rlm_cache_rbtree) loaded and linked
  # Instantiating module "mschap" from file /usr/local/etc/raddb/mods-enabled/mschap
rlm_mschap (mschap): using internal authentication
  # Instantiating module "IPASS" from file /usr/local/etc/raddb/mods-enabled/realm
  # Instantiating module "suffix" from file /usr/local/etc/raddb/mods-enabled/realm
  # Instantiating module "realmpercent" from file /usr/local/etc/raddb/mods-enabled/realm
  # Instantiating module "ntdomain" from file /usr/local/etc/raddb/mods-enabled/realm
  # Instantiating module "attr_filter.post-proxy" from file /usr/local/etc/raddb/mods-enabled/attr_filter
reading pairlist file /usr/local/etc/raddb/mods-config/attr_filter/post-proxy
  # Instantiating module "attr_filter.pre-proxy" from file /usr/local/etc/raddb/mods-enabled/attr_filter
reading pairlist file /usr/local/etc/raddb/mods-config/attr_filter/pre-proxy
  # Instantiating module "attr_filter.access_reject" from file /usr/local/etc/raddb/mods-enabled/attr_filter
reading pairlist file /usr/local/etc/raddb/mods-config/attr_filter/access_reject
[/usr/local/etc/raddb/mods-config/attr_filter/access_reject]:11 Check item "FreeRADIUS-Response-Delay"   found in filter list for realm "DEFAULT".
[/usr/local/etc/raddb/mods-config/attr_filter/access_reject]:11 Check item "FreeRADIUS-Response-Delay-USec"      found in filter list for realm "DEFAULT".
  # Instantiating module "attr_filter.access_challenge" from file /usr/local/etc/raddb/mods-enabled/attr_filter
reading pairlist file /usr/local/etc/raddb/mods-config/attr_filter/access_challenge
  # Instantiating module "attr_filter.accounting_response" from file /usr/local/etc/raddb/mods-enabled/attr_filter
reading pairlist file /usr/local/etc/raddb/mods-config/attr_filter/accounting_response
  # Instantiating module "linelog" from file /usr/local/etc/raddb/mods-enabled/linelog
  # Instantiating module "log_accounting" from file /usr/local/etc/raddb/mods-enabled/linelog
  # Instantiating module "eap" from file /usr/local/etc/raddb/mods-enabled/eap
   # Linked to sub-module rlm_eap_tls
   tls {
        tls = "tls-common"
   }
   tls-config tls-common {
        verify_depth = 0
        ca_path = "/usr/local/etc/raddb/certs"
        pem_file_type = yes
        private_key_file = "/usr/local/etc/raddb/certs/server.pem"
        certificate_file = "/usr/local/etc/raddb/certs/server.pem"
        ca_file = "/usr/local/etc/raddb/certs/ca.pem"
        private_key_password = <<< secret >>>
        dh_file = "/usr/local/etc/raddb/certs/dh"
        fragment_size = 1024
        include_length = yes
        auto_chain = yes
        check_crl = no
        check_all_crl = no
        cipher_list = "HIGH"
        cipher_server_preference = no
        ecdh_curve = "prime256v1"
        tls_max_version = ""
        tls_min_version = "1.0"
    cache {
        enable = no
        lifetime = 24
        max_entries = 255
    }
    verify {
        skip_if_ocsp_ok = no
        tmpdir = "/tmp/radiusd"
        client = "/usr/bin/openssl verify -CApath /usr/local/etc/raddb/certs %{TLS-Client-Cert-Filename}"
    }
    ocsp {
        enable = no
        override_cert_url = yes
        url = "http://127.0.0.1/ocsp/"
        use_nonce = yes
        timeout = 0
        softfail = no
    }
   }
  # Instantiating module "pap" from file /usr/local/etc/raddb/mods-enabled/pap
  # Instantiating module "auth_log" from file /usr/local/etc/raddb/mods-enabled/detail.log
rlm_detail (auth_log): 'User-Password' suppressed, will not appear in detail output
  # Instantiating module "reply_log" from file /usr/local/etc/raddb/mods-enabled/detail.log
  # Instantiating module "pre_proxy_log" from file /usr/local/etc/raddb/mods-enabled/detail.log
  # Instantiating module "post_proxy_log" from file /usr/local/etc/raddb/mods-enabled/detail.log
  # Instantiating module "logintime" from file /usr/local/etc/raddb/mods-enabled/logintime
  # Instantiating module "reject" from file /usr/local/etc/raddb/mods-enabled/always
  # Instantiating module "fail" from file /usr/local/etc/raddb/mods-enabled/always
  # Instantiating module "ok" from file /usr/local/etc/raddb/mods-enabled/always
  # Instantiating module "handled" from file /usr/local/etc/raddb/mods-enabled/always
  # Instantiating module "invalid" from file /usr/local/etc/raddb/mods-enabled/always
  # Instantiating module "userlock" from file /usr/local/etc/raddb/mods-enabled/always
  # Instantiating module "notfound" from file /usr/local/etc/raddb/mods-enabled/always
  # Instantiating module "noop" from file /usr/local/etc/raddb/mods-enabled/always
  # Instantiating module "updated" from file /usr/local/etc/raddb/mods-enabled/always
  # Instantiating module "preprocess" from file /usr/local/etc/raddb/mods-enabled/preprocess
reading pairlist file /usr/local/etc/raddb/mods-config/preprocess/huntgroups
reading pairlist file /usr/local/etc/raddb/mods-config/preprocess/hints
  # Instantiating module "ldap" from file /usr/local/etc/raddb/mods-enabled/ldap
rlm_ldap: libldap vendor: OpenLDAP, version: 20442
   accounting {
        reference = "%{tolower:type.%{Acct-Status-Type}}"
   }
   post-auth {
        reference = "."
   }
rlm_ldap (ldap): Initialising connection pool
   pool {
        start = 5
        min = 3
        max = 32
        spare = 10
        uses = 0
        lifetime = 0
        cleanup_interval = 30
        idle_timeout = 60
        retry_delay = 30
        spread = no
   }
rlm_ldap (ldap): Opening additional connection (0), 1 of 32 pending slots used
rlm_ldap (ldap): Connecting to ldap://Domain.net:389
rlm_ldap (ldap): Waiting for bind result...
rlm_ldap (ldap): Bind successful
rlm_ldap (ldap): Opening additional connection (1), 1 of 31 pending slots used
rlm_ldap (ldap): Connecting to ldap://Domain.net:389
rlm_ldap (ldap): Waiting for bind result...
rlm_ldap (ldap): Bind successful
rlm_ldap (ldap): Opening additional connection (2), 1 of 30 pending slots used
rlm_ldap (ldap): Connecting to ldap://Domain.net:389
rlm_ldap (ldap): Waiting for bind result...
rlm_ldap (ldap): Bind successful
rlm_ldap (ldap): Opening additional connection (3), 1 of 29 pending slots used
rlm_ldap (ldap): Connecting to ldap://Domain.net:389
rlm_ldap (ldap): Waiting for bind result...
rlm_ldap (ldap): Bind successful
rlm_ldap (ldap): Opening additional connection (4), 1 of 28 pending slots used
rlm_ldap (ldap): Connecting to ldap://Domain.net:389
rlm_ldap (ldap): Waiting for bind result...
rlm_ldap (ldap): Bind successful
  # Instantiating module "expiration" from file /usr/local/etc/raddb/mods-enabled/expiration
  # Instantiating module "etc_passwd" from file /usr/local/etc/raddb/mods-enabled/passwd
rlm_passwd: nfields: 3 keyfield 0(User-Name) listable: no
 } # modules
radiusd: #### Loading Virtual Servers ####
server { # from file /usr/local/etc/raddb/radiusd.conf
} # server
server inner-tunnel { # from file /usr/local/etc/raddb/sites-enabled/inner-tunnel
 # Loading authenticate {...}
 # Loading authorize {...}
Ignoring "sql" (see raddb/mods-available/README.rst)
 # Loading session {...}
 # Loading post-proxy {...}
 # Loading post-auth {...}
 # Skipping contents of 'if' as it is always 'false' -- /usr/local/etc/raddb/sites-enabled/inner-tunnel:332
} # server inner-tunnel
server default { # from file /usr/local/etc/raddb/sites-enabled/default
 # Loading authenticate {...}
 # Loading authorize {...}
 # Loading preacct {...}
 # Loading accounting {...}
 # Loading post-proxy {...}
 # Loading post-auth {...}
} # server default
radiusd: #### Opening IP addresses and Ports ####
listen {
        type = "auth"
        ipaddr = 127.0.0.1
        port = 18120
}
listen {
        type = "auth"
        ipaddr = *
        port = 0
   limit {
        max_connections = 16
        lifetime = 0
        idle_timeout = 30
   }
}
listen {
        type = "acct"
        ipaddr = *
        port = 0
   limit {
        max_connections = 16
        lifetime = 0
        idle_timeout = 30
   }
}
listen {
        type = "auth"
        ipv6addr = ::
        port = 0
   limit {
        max_connections = 16
        lifetime = 0
        idle_timeout = 30
   }
}
listen {
        type = "acct"
        ipv6addr = ::
        port = 0
   limit {
        max_connections = 16
        lifetime = 0
        idle_timeout = 30
   }
}
Listening on auth address 127.0.0.1 port 18120 bound to server inner-tunnel
Listening on auth address * port 1812 bound to server default
Listening on acct address * port 1813 bound to server default
Listening on auth address :: port 1812 bound to server default
Listening on acct address :: port 1813 bound to server default
Listening on proxy address * port 36409
Listening on proxy address :: port 64651
Ready to process requests
(0) Received Access-Request Id 0 from 127.0.0.1:36789 to 127.0.0.1:1812 length 134
(0)   User-Name = "client.pem"
(0)   NAS-IP-Address = 127.0.0.1
(0)   Calling-Station-Id = "02-00-00-00-00-01"
(0)   Framed-MTU = 1400
(0)   NAS-Port-Type = Wireless-802.11
(0)   Service-Type = Framed-User
(0)   Connect-Info = "CONNECT 11Mbps 802.11b"
(0)   EAP-Message = 0x0200000f01636c69656e742e70656d
(0)   Message-Authenticator = 0xd00906a3d0648e3a771145edfd1b9f36
(0) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default
(0)   authorize {
(0)     policy filter_username {
(0)       if (&User-Name) {
(0)       if (&User-Name)  -> TRUE
(0)       if (&User-Name)  {
(0)         if (&User-Name =~ / /) {
(0)         if (&User-Name =~ / /)  -> FALSE
(0)         if (&User-Name =~ /@[^@]*@/ ) {
(0)         if (&User-Name =~ /@[^@]*@/ )  -> FALSE
(0)         if (&User-Name =~ /\.\./ ) {
(0)         if (&User-Name =~ /\.\./ )  -> FALSE
(0)         if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/))  {
(0)         if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/))   -> FALSE
(0)         if (&User-Name =~ /\.$/)  {
(0)         if (&User-Name =~ /\.$/)   -> FALSE
(0)         if (&User-Name =~ /@\./)  {
(0)         if (&User-Name =~ /@\./)   -> FALSE
(0)       } # if (&User-Name)  = notfound
(0)     } # policy filter_username = notfound
(0)     [preprocess] = ok
(0) auth_log: EXPAND /usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d
(0) auth_log:    --> /usr/local/var/log/radius/radacct/127.0.0.1/auth-detail-20180821
(0) auth_log: /usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d expands to /usr/local/var/log/radius/radacct/127.0.0.1/auth-detail-20180821
(0) auth_log: EXPAND %t
(0) auth_log:    --> Tue Aug 21 19:09:39 2018
(0)     [auth_log] = ok
(0) eap: Peer sent EAP Response (code 2) ID 0 length 15
(0) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize
(0)     [eap] = ok
(0)   } # authorize = ok
(0) Found Auth-Type = eap
(0) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(0)   authenticate {
(0) eap: Peer sent packet with method EAP Identity (1)
(0) eap: Calling submodule eap_tls to process data
(0) eap_tls: Initiating new EAP-TLS session
(0) eap_tls: Setting verify mode to require certificate from client
(0) eap_tls: [eaptls start] = request
(0) eap: Sending EAP Request (code 1) ID 1 length 6
(0) eap: EAP session adding &reply:State = 0x8db2a5328db3a858
(0)     [eap] = handled
(0)   } # authenticate = handled
(0) Using Post-Auth-Type Challenge
(0) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(0)   Challenge { ... } # empty sub-section is ignored
(0) Sent Access-Challenge Id 0 from 127.0.0.1:1812 to 127.0.0.1:36789 length 0
(0)   EAP-Message = 0x010100060d20
(0)   Message-Authenticator = 0x00000000000000000000000000000000
(0)   State = 0x8db2a5328db3a858fbbf5fa81909ec3c
(0) Finished request
Waking up in 4.9 seconds.
(1) Received Access-Request Id 1 from 127.0.0.1:36789 to 127.0.0.1:1812 length 446
(1)   User-Name = "client.pem"
(1)   NAS-IP-Address = 127.0.0.1
(1)   Calling-Station-Id = "02-00-00-00-00-01"
(1)   Framed-MTU = 1400
(1)   NAS-Port-Type = Wireless-802.11
(1)   Service-Type = Framed-User
(1)   Connect-Info = "CONNECT 11Mbps 802.11b"
(1)   EAP-Message = 0x020101330d0016030101280100012403039c4469b54ea5c4edd45618780c24fa5ca5f8897d2e475569a1553c51469fb9470000aac030c02cc028c024c014c00a00a500a300a1009f006b006a0069006800390038003700360088008700860085c032c02ec02ac026c00fc005009d003d00350084c02fc0
(1)   State = 0x8db2a5328db3a858fbbf5fa81909ec3c
(1)   Message-Authenticator = 0xae86ca804883a58af655d7ad8ce39609
(1) session-state: No cached attributes
(1) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default
(1)   authorize {
(1)     policy filter_username {
(1)       if (&User-Name) {
(1)       if (&User-Name)  -> TRUE
(1)       if (&User-Name)  {
(1)         if (&User-Name =~ / /) {
(1)         if (&User-Name =~ / /)  -> FALSE
(1)         if (&User-Name =~ /@[^@]*@/ ) {
(1)         if (&User-Name =~ /@[^@]*@/ )  -> FALSE
(1)         if (&User-Name =~ /\.\./ ) {
(1)         if (&User-Name =~ /\.\./ )  -> FALSE
(1)         if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/))  {
(1)         if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/))   -> FALSE
(1)         if (&User-Name =~ /\.$/)  {
(1)         if (&User-Name =~ /\.$/)   -> FALSE
(1)         if (&User-Name =~ /@\./)  {
(1)         if (&User-Name =~ /@\./)   -> FALSE
(1)       } # if (&User-Name)  = notfound
(1)     } # policy filter_username = notfound
(1)     [preprocess] = ok
(1) auth_log: EXPAND /usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d
(1) auth_log:    --> /usr/local/var/log/radius/radacct/127.0.0.1/auth-detail-20180821
(1) auth_log: /usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d expands to /usr/local/var/log/radius/radacct/127.0.0.1/auth-detail-20180821
(1) auth_log: EXPAND %t
(1) auth_log:    --> Tue Aug 21 19:09:39 2018
(1)     [auth_log] = ok
(1) eap: Peer sent EAP Response (code 2) ID 1 length 307
(1) eap: No EAP Start, assuming it's an on-going EAP conversation
(1)     [eap] = updated
(1) files: users: Matched entry DEFAULT at line 1
(1)     [files] = ok
(1)     [expiration] = noop
(1)     [logintime] = noop
(1)   } # authorize = updated
(1) Found Auth-Type = eap
(1) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(1)   authenticate {
(1) eap: Expiring EAP session with state 0x8db2a5328db3a858
(1) eap: Finished EAP session with state 0x8db2a5328db3a858
(1) eap: Previous EAP request found for state 0x8db2a5328db3a858, released from the list
(1) eap: Peer sent packet with method EAP TLS (13)
(1) eap: Calling submodule eap_tls to process data
(1) eap_tls: Continuing EAP-TLS
(1) eap_tls: Got final TLS record fragment (301 bytes)
(1) eap_tls: WARNING: Total received TLS record fragments (301 bytes), does not equal indicated TLS record length (0 bytes)
(1) eap_tls: [eaptls verify] = ok
(1) eap_tls: Done initial handshake
(1) eap_tls: (other): before/accept initialization
(1) eap_tls: TLS_accept: before/accept initialization
(1) eap_tls: <<< recv TLS 1.2  [length 0128]
(1) eap_tls: TLS_accept: unknown state
(1) eap_tls: >>> send TLS 1.2  [length 003e]
(1) eap_tls: TLS_accept: unknown state
(1) eap_tls: >>> send TLS 1.2  [length 0885]
(1) eap_tls: TLS_accept: unknown state
(1) eap_tls: >>> send TLS 1.2  [length 014d]
(1) eap_tls: TLS_accept: unknown state
(1) eap_tls: >>> send TLS 1.2  [length 00b6]
(1) eap_tls: TLS_accept: unknown state
(1) eap_tls: TLS_accept: unknown state
(1) eap_tls: TLS_accept: Need to read more data: unknown state
(1) eap_tls: TLS_accept: Need to read more data: unknown state
(1) eap_tls: In SSL Handshake Phase
(1) eap_tls: In SSL Accept mode
(1) eap_tls: [eaptls process] = handled
(1) eap: Sending EAP Request (code 1) ID 2 length 1024
(1) eap: EAP session adding &reply:State = 0x8db2a5328cb0a858
(1)     [eap] = handled
(1)   } # authenticate = handled
(1) Using Post-Auth-Type Challenge
(1) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(1)   Challenge { ... } # empty sub-section is ignored
(1) Sent Access-Challenge Id 1 from 127.0.0.1:1812 to 127.0.0.1:36789 length 0
(1)   EAP-Message = 0x010204000dc000000ada160303003e0200003a03031b79870f786030224aafaf12faf3cb11780b455b25fcdd8f3be3c65bd5d54eb400c030000012ff01000100000b000403000102000f00010116030308850b00088100087e0003c0308203bc308202a4a003020102020101300d06092a864886f70d01
(1)   Message-Authenticator = 0x00000000000000000000000000000000
(1)   State = 0x8db2a5328cb0a858fbbf5fa81909ec3c
(1) Finished request
Waking up in 4.9 seconds.
(2) Received Access-Request Id 2 from 127.0.0.1:36789 to 127.0.0.1:1812 length 143
(2)   User-Name = "client.pem"
(2)   NAS-IP-Address = 127.0.0.1
(2)   Calling-Station-Id = "02-00-00-00-00-01"
(2)   Framed-MTU = 1400
(2)   NAS-Port-Type = Wireless-802.11
(2)   Service-Type = Framed-User
(2)   Connect-Info = "CONNECT 11Mbps 802.11b"
(2)   EAP-Message = 0x020200060d00
(2)   State = 0x8db2a5328cb0a858fbbf5fa81909ec3c
(2)   Message-Authenticator = 0x09374abbc754eba45442ae669e219bc7
(2) session-state: No cached attributes
(2) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default
(2)   authorize {
(2)     policy filter_username {
(2)       if (&User-Name) {
(2)       if (&User-Name)  -> TRUE
(2)       if (&User-Name)  {
(2)         if (&User-Name =~ / /) {
(2)         if (&User-Name =~ / /)  -> FALSE
(2)         if (&User-Name =~ /@[^@]*@/ ) {
(2)         if (&User-Name =~ /@[^@]*@/ )  -> FALSE
(2)         if (&User-Name =~ /\.\./ ) {
(2)         if (&User-Name =~ /\.\./ )  -> FALSE
(2)         if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/))  {
(2)         if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/))   -> FALSE
(2)         if (&User-Name =~ /\.$/)  {
(2)         if (&User-Name =~ /\.$/)   -> FALSE
(2)         if (&User-Name =~ /@\./)  {
(2)         if (&User-Name =~ /@\./)   -> FALSE
(2)       } # if (&User-Name)  = notfound
(2)     } # policy filter_username = notfound
(2)     [preprocess] = ok
(2) auth_log: EXPAND /usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d
(2) auth_log:    --> /usr/local/var/log/radius/radacct/127.0.0.1/auth-detail-20180821
(2) auth_log: /usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d expands to /usr/local/var/log/radius/radacct/127.0.0.1/auth-detail-20180821
(2) auth_log: EXPAND %t
(2) auth_log:    --> Tue Aug 21 19:09:39 2018
(2)     [auth_log] = ok
(2) eap: Peer sent EAP Response (code 2) ID 2 length 6
(2) eap: No EAP Start, assuming it's an on-going EAP conversation
(2)     [eap] = updated
(2) files: users: Matched entry DEFAULT at line 1
(2)     [files] = ok
(2)     [expiration] = noop
(2)     [logintime] = noop
(2)   } # authorize = updated
(2) Found Auth-Type = eap
(2) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(2)   authenticate {
(2) eap: Expiring EAP session with state 0x8db2a5328cb0a858
(2) eap: Finished EAP session with state 0x8db2a5328cb0a858
(2) eap: Previous EAP request found for state 0x8db2a5328cb0a858, released from the list
(2) eap: Peer sent packet with method EAP TLS (13)
(2) eap: Calling submodule eap_tls to process data
(2) eap_tls: Continuing EAP-TLS
(2) eap_tls: Peer ACKed our handshake fragment
(2) eap_tls: [eaptls verify] = request
(2) eap_tls: [eaptls process] = handled
(2) eap: Sending EAP Request (code 1) ID 3 length 1024
(2) eap: EAP session adding &reply:State = 0x8db2a5328fb1a858
(2)     [eap] = handled
(2)   } # authenticate = handled
(2) Using Post-Auth-Type Challenge
(2) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(2)   Challenge { ... } # empty sub-section is ignored
(2) Sent Access-Challenge Id 2 from 127.0.0.1:1812 to 127.0.0.1:36789 length 0
(2)   EAP-Message = 0x010304000dc000000ada3fc6f74e554b65096cf1c9576d66e5a1b19b053f667702d6acbfd8730004b8308204b43082039ca003020102020900c600a5ee176d055c300d06092a864886f70d01010b0500308183310b3009060355040613025553310b300906035504080c0257413113301106035504070c
(2)   Message-Authenticator = 0x00000000000000000000000000000000
(2)   State = 0x8db2a5328fb1a858fbbf5fa81909ec3c
(2) Finished request
Waking up in 4.9 seconds.
(3) Received Access-Request Id 3 from 127.0.0.1:36789 to 127.0.0.1:1812 length 143
(3)   User-Name = "client.pem"
(3)   NAS-IP-Address = 127.0.0.1
(3)   Calling-Station-Id = "02-00-00-00-00-01"
(3)   Framed-MTU = 1400
(3)   NAS-Port-Type = Wireless-802.11
(3)   Service-Type = Framed-User
(3)   Connect-Info = "CONNECT 11Mbps 802.11b"
(3)   EAP-Message = 0x020300060d00
(3)   State = 0x8db2a5328fb1a858fbbf5fa81909ec3c
(3)   Message-Authenticator = 0x32b0f0985f480c56b06736c57595844b
(3) session-state: No cached attributes
(3) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default
(3)   authorize {
(3)     policy filter_username {
(3)       if (&User-Name) {
(3)       if (&User-Name)  -> TRUE
(3)       if (&User-Name)  {
(3)         if (&User-Name =~ / /) {
(3)         if (&User-Name =~ / /)  -> FALSE
(3)         if (&User-Name =~ /@[^@]*@/ ) {
(3)         if (&User-Name =~ /@[^@]*@/ )  -> FALSE
(3)         if (&User-Name =~ /\.\./ ) {
(3)         if (&User-Name =~ /\.\./ )  -> FALSE
(3)         if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/))  {
(3)         if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/))   -> FALSE
(3)         if (&User-Name =~ /\.$/)  {
(3)         if (&User-Name =~ /\.$/)   -> FALSE
(3)         if (&User-Name =~ /@\./)  {
(3)         if (&User-Name =~ /@\./)   -> FALSE
(3)       } # if (&User-Name)  = notfound
(3)     } # policy filter_username = notfound
(3)     [preprocess] = ok
(3) auth_log: EXPAND /usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d
(3) auth_log:    --> /usr/local/var/log/radius/radacct/127.0.0.1/auth-detail-20180821
(3) auth_log: /usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d expands to /usr/local/var/log/radius/radacct/127.0.0.1/auth-detail-20180821
(3) auth_log: EXPAND %t
(3) auth_log:    --> Tue Aug 21 19:09:39 2018
(3)     [auth_log] = ok
(3) eap: Peer sent EAP Response (code 2) ID 3 length 6
(3) eap: No EAP Start, assuming it's an on-going EAP conversation
(3)     [eap] = updated
(3) files: users: Matched entry DEFAULT at line 1
(3)     [files] = ok
(3)     [expiration] = noop
(3)     [logintime] = noop
(3)   } # authorize = updated
(3) Found Auth-Type = eap
(3) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(3)   authenticate {
(3) eap: Expiring EAP session with state 0x8db2a5328fb1a858
(3) eap: Finished EAP session with state 0x8db2a5328fb1a858
(3) eap: Previous EAP request found for state 0x8db2a5328fb1a858, released from the list
(3) eap: Peer sent packet with method EAP TLS (13)
(3) eap: Calling submodule eap_tls to process data
(3) eap_tls: Continuing EAP-TLS
(3) eap_tls: Peer ACKed our handshake fragment
(3) eap_tls: [eaptls verify] = request
(3) eap_tls: [eaptls process] = handled
(3) eap: Sending EAP Request (code 1) ID 4 length 760
(3) eap: EAP session adding &reply:State = 0x8db2a5328eb6a858
(3)     [eap] = handled
(3)   } # authenticate = handled
(3) Using Post-Auth-Type Challenge
(3) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(3)   Challenge { ... } # empty sub-section is ignored
(3) Sent Access-Challenge Id 3 from 127.0.0.1:1812 to 127.0.0.1:36789 length 0
(3)   EAP-Message = 0x010402f80d8000000adaa158fd0cacf5726c80718dfbaa6c75fa64462d6736903610eb5f1638a7ba7c925b858636296265568e5076bed345f273aaa1d83a2e064f5e6d266da1b233d94533b8803e497f4f37900c0cb829a3f04bc6d4b610dee50a8a47dad71eec9a5ba6538c81bf9bb7fae723a0a61b23
(3)   Message-Authenticator = 0x00000000000000000000000000000000
(3)   State = 0x8db2a5328eb6a858fbbf5fa81909ec3c
(3) Finished request
Waking up in 4.9 seconds.
(4) Received Access-Request Id 4 from 127.0.0.1:36789 to 127.0.0.1:1812 length 1555
(4)   User-Name = "client.pem"
(4)   NAS-IP-Address = 127.0.0.1
(4)   Calling-Station-Id = "02-00-00-00-00-01"
(4)   Framed-MTU = 1400
(4)   NAS-Port-Type = Wireless-802.11
(4)   Service-Type = Framed-User
(4)   Connect-Info = "CONNECT 11Mbps 802.11b"
(4)   EAP-Message = 0x020405800dc000000a1316030308830b00087f00087c0003be308203ba308202a2a003020102020102300d06092a864886f70d01010b0500308183310b3009060355040613025553310b300906035504080c0257413113301106035504070c0a42656c6c696e6768616d31123010060355040a0c094661
(4)   State = 0x8db2a5328eb6a858fbbf5fa81909ec3c
(4)   Message-Authenticator = 0x9073f436730652ec433ae776fd3f8183
(4) session-state: No cached attributes
(4) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default
(4)   authorize {
(4)     policy filter_username {
(4)       if (&User-Name) {
(4)       if (&User-Name)  -> TRUE
(4)       if (&User-Name)  {
(4)         if (&User-Name =~ / /) {
(4)         if (&User-Name =~ / /)  -> FALSE
(4)         if (&User-Name =~ /@[^@]*@/ ) {
(4)         if (&User-Name =~ /@[^@]*@/ )  -> FALSE
(4)         if (&User-Name =~ /\.\./ ) {
(4)         if (&User-Name =~ /\.\./ )  -> FALSE
(4)         if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/))  {
(4)         if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/))   -> FALSE
(4)         if (&User-Name =~ /\.$/)  {
(4)         if (&User-Name =~ /\.$/)   -> FALSE
(4)         if (&User-Name =~ /@\./)  {
(4)         if (&User-Name =~ /@\./)   -> FALSE
(4)       } # if (&User-Name)  = notfound
(4)     } # policy filter_username = notfound
(4)     [preprocess] = ok
(4) auth_log: EXPAND /usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d
(4) auth_log:    --> /usr/local/var/log/radius/radacct/127.0.0.1/auth-detail-20180821
(4) auth_log: /usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d expands to /usr/local/var/log/radius/radacct/127.0.0.1/auth-detail-20180821
(4) auth_log: EXPAND %t
(4) auth_log:    --> Tue Aug 21 19:09:39 2018
(4)     [auth_log] = ok
(4) eap: Peer sent EAP Response (code 2) ID 4 length 1408
(4) eap: No EAP Start, assuming it's an on-going EAP conversation
(4)     [eap] = updated
(4) files: users: Matched entry DEFAULT at line 1
(4)     [files] = ok
(4)     [expiration] = noop
(4)     [logintime] = noop
(4)   } # authorize = updated
(4) Found Auth-Type = eap
(4) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(4)   authenticate {
(4) eap: Expiring EAP session with state 0x8db2a5328eb6a858
(4) eap: Finished EAP session with state 0x8db2a5328eb6a858
(4) eap: Previous EAP request found for state 0x8db2a5328eb6a858, released from the list
(4) eap: Peer sent packet with method EAP TLS (13)
(4) eap: Calling submodule eap_tls to process data
(4) eap_tls: Continuing EAP-TLS
(4) eap_tls: Peer indicated complete TLS record size will be 2579 bytes
(4) eap_tls: Expecting 2 TLS record fragments
(4) eap_tls: Got first TLS record fragment (1398 bytes).  Peer indicated more fragments to follow
(4) eap_tls: [eaptls verify] = first fragment
(4) eap_tls: ACKing Peer's TLS record fragment
(4) eap_tls: [eaptls process] = handled
(4) eap: Sending EAP Request (code 1) ID 5 length 6
(4) eap: EAP session adding &reply:State = 0x8db2a53289b7a858
(4)     [eap] = handled
(4)   } # authenticate = handled
(4) Using Post-Auth-Type Challenge
(4) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(4)   Challenge { ... } # empty sub-section is ignored
(4) Sent Access-Challenge Id 4 from 127.0.0.1:1812 to 127.0.0.1:36789 length 0
(4)   EAP-Message = 0x010500060d00
(4)   Message-Authenticator = 0x00000000000000000000000000000000
(4)   State = 0x8db2a53289b7a858fbbf5fa81909ec3c
(4) Finished request
Waking up in 4.9 seconds.
(5) Received Access-Request Id 5 from 127.0.0.1:36789 to 127.0.0.1:1812 length 1332
(5)   User-Name = "client.pem"
(5)   NAS-IP-Address = 127.0.0.1
(5)   Calling-Station-Id = "02-00-00-00-00-01"
(5)   Framed-MTU = 1400
(5)   NAS-Port-Type = Wireless-802.11
(5)   Service-Type = Framed-User
(5)   Connect-Info = "CONNECT 11Mbps 802.11b"
(5)   EAP-Message = 0x020504a30d009fd708c7fc4135e2c21b17e472a506e56bec63fd54772c0a3de87ec11d4dac88eeaf28e4c60bb8d1437218453166810fe18d87ca8ea690e9b386b211e159030d338d9af4acfc6b71505764594c6c1b85eced7cf21301ca8c1eca8f2752f3c06098f8efcab9203bb480391976249f12e805
(5)   State = 0x8db2a53289b7a858fbbf5fa81909ec3c
(5)   Message-Authenticator = 0x2b66063c58bd994f19a3dcc4fae8afdc
(5) session-state: No cached attributes
(5) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default
(5)   authorize {
(5)     policy filter_username {
(5)       if (&User-Name) {
(5)       if (&User-Name)  -> TRUE
(5)       if (&User-Name)  {
(5)         if (&User-Name =~ / /) {
(5)         if (&User-Name =~ / /)  -> FALSE
(5)         if (&User-Name =~ /@[^@]*@/ ) {
(5)         if (&User-Name =~ /@[^@]*@/ )  -> FALSE
(5)         if (&User-Name =~ /\.\./ ) {
(5)         if (&User-Name =~ /\.\./ )  -> FALSE
(5)         if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/))  {
(5)         if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/))   -> FALSE
(5)         if (&User-Name =~ /\.$/)  {
(5)         if (&User-Name =~ /\.$/)   -> FALSE
(5)         if (&User-Name =~ /@\./)  {
(5)         if (&User-Name =~ /@\./)   -> FALSE
(5)       } # if (&User-Name)  = notfound
(5)     } # policy filter_username = notfound
(5)     [preprocess] = ok
(5) auth_log: EXPAND /usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d
(5) auth_log:    --> /usr/local/var/log/radius/radacct/127.0.0.1/auth-detail-20180821
(5) auth_log: /usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d expands to /usr/local/var/log/radius/radacct/127.0.0.1/auth-detail-20180821
(5) auth_log: EXPAND %t
(5) auth_log:    --> Tue Aug 21 19:09:39 2018
(5)     [auth_log] = ok
(5) eap: Peer sent EAP Response (code 2) ID 5 length 1187
(5) eap: No EAP Start, assuming it's an on-going EAP conversation
(5)     [eap] = updated
(5) files: users: Matched entry DEFAULT at line 1
(5)     [files] = ok
(5)     [expiration] = noop
(5)     [logintime] = noop
(5)   } # authorize = updated
(5) Found Auth-Type = eap
(5) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(5)   authenticate {
(5) eap: Expiring EAP session with state 0x8db2a53289b7a858
(5) eap: Finished EAP session with state 0x8db2a53289b7a858
(5) eap: Previous EAP request found for state 0x8db2a53289b7a858, released from the list
(5) eap: Peer sent packet with method EAP TLS (13)
(5) eap: Calling submodule eap_tls to process data
(5) eap_tls: Continuing EAP-TLS
(5) eap_tls: Got final TLS record fragment (1181 bytes)
(5) eap_tls: [eaptls verify] = ok
(5) eap_tls: Done initial handshake
(5) eap_tls: <<< recv TLS 1.2  [length 0883]
(5) eap_tls: Creating attributes from certificate OIDs
(5) eap_tls:   TLS-Cert-Serial := "c600a5ee176d055c"
(5) eap_tls:   TLS-Cert-Expiration := "181019201014Z"
(5) eap_tls:   TLS-Cert-Subject := "/C=US/ST=WA/L=Town/O=company/emailAddress=admintest at email.com/CN=Radius Server"
(5) eap_tls:   TLS-Cert-Issuer := "/C=US/ST=WA/L=Town/O=company/emailAddress=admintest at email.com/CN=Radius Server"
(5) eap_tls:   TLS-Cert-Common-Name := "Radius Server"
(5) eap_tls: Creating attributes from certificate OIDs
(5) eap_tls:   TLS-Client-Cert-Serial := "02"
(5) eap_tls:   TLS-Client-Cert-Expiration := "181019201107Z"
(5) eap_tls:   TLS-Client-Cert-Subject := "/C=US/ST=WA/O=company/CN=kevin.test/emailAddress=kevin.test at email.com"
(5) eap_tls:   TLS-Client-Cert-Issuer := "/C=US/ST=WA/L=Town/O=company/emailAddress=admintest at email.com/CN=Radius Server"
(5) eap_tls:   TLS-Client-Cert-Common-Name := "kevin.test"
(5) eap_tls:   TLS-Client-Cert-X509v3-Extended-Key-Usage += "TLS Web Client Authentication"
(5) eap_tls:   TLS-Client-Cert-X509v3-Extended-Key-Usage-OID += "1.3.6.1.5.5.7.3.2"
(5) eap_tls: Verifying client certificate: /usr/bin/openssl verify -CApath /usr/local/etc/raddb/certs %{TLS-Client-Cert-Filename}
(5) eap_tls: Executing: /usr/bin/openssl verify -CApath /usr/local/etc/raddb/certs %{TLS-Client-Cert-Filename}:
(5) eap_tls: EXPAND %{TLS-Client-Cert-Filename}
(5) eap_tls:    --> /tmp/radiusd/radiusd.client.XX6sVjt9
(5) eap_tls: Program returned code (0) and output '/tmp/radiusd/radiusd.client.XX6sVjt9: OK'
(5) eap_tls: Client certificate CN kevin.test passed external validation
(5) eap_tls: TLS_accept: unknown state
(5) eap_tls: <<< recv TLS 1.2  [length 0046]
(5) eap_tls: TLS_accept: unknown state
(5) eap_tls: <<< recv TLS 1.2  [length 0108]
(5) eap_tls: TLS_accept: unknown state
(5) eap_tls: <<< recv TLS 1.2  [length 0001]
(5) eap_tls: <<< recv TLS 1.2  [length 0010]
(5) eap_tls: TLS_accept: unknown state
(5) eap_tls: >>> send TLS 1.2  [length 0001]
(5) eap_tls: TLS_accept: unknown state
(5) eap_tls: >>> send TLS 1.2  [length 0010]
(5) eap_tls: TLS_accept: unknown state
(5) eap_tls: TLS_accept: unknown state
(5) eap_tls: (other): SSL negotiation finished successfully
(5) eap_tls: SSL Connection Established
(5) eap_tls: [eaptls process] = handled
(5) eap: Sending EAP Request (code 1) ID 6 length 61
(5) eap: EAP session adding &reply:State = 0x8db2a53288b4a858
(5)     [eap] = handled
(5)   } # authenticate = handled
(5) Using Post-Auth-Type Challenge
(5) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(5)   Challenge { ... } # empty sub-section is ignored
(5) Sent Access-Challenge Id 5 from 127.0.0.1:1812 to 127.0.0.1:36789 length 0
(5)   EAP-Message = 0x0106003d0d80000000331403030001011603030028381c7e1783d65af09f05df42d3f1b2fed20f91d132889dc662acf7908c7b8dd2a1a9530889f2030a
(5)   Message-Authenticator = 0x00000000000000000000000000000000
(5)   State = 0x8db2a53288b4a858fbbf5fa81909ec3c
(5) Finished request
Waking up in 4.9 seconds.
(6) Received Access-Request Id 6 from 127.0.0.1:36789 to 127.0.0.1:1812 length 143
(6)   User-Name = "client.pem"
(6)   NAS-IP-Address = 127.0.0.1
(6)   Calling-Station-Id = "02-00-00-00-00-01"
(6)   Framed-MTU = 1400
(6)   NAS-Port-Type = Wireless-802.11
(6)   Service-Type = Framed-User
(6)   Connect-Info = "CONNECT 11Mbps 802.11b"
(6)   EAP-Message = 0x020600060d00
(6)   State = 0x8db2a53288b4a858fbbf5fa81909ec3c
(6)   Message-Authenticator = 0x3ffc0b16b3614022609b9f298eafda17
(6) session-state: No cached attributes
(6) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default
(6)   authorize {
(6)     policy filter_username {
(6)       if (&User-Name) {
(6)       if (&User-Name)  -> TRUE
(6)       if (&User-Name)  {
(6)         if (&User-Name =~ / /) {
(6)         if (&User-Name =~ / /)  -> FALSE
(6)         if (&User-Name =~ /@[^@]*@/ ) {
(6)         if (&User-Name =~ /@[^@]*@/ )  -> FALSE
(6)         if (&User-Name =~ /\.\./ ) {
(6)         if (&User-Name =~ /\.\./ )  -> FALSE
(6)         if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/))  {
(6)         if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/))   -> FALSE
(6)         if (&User-Name =~ /\.$/)  {
(6)         if (&User-Name =~ /\.$/)   -> FALSE
(6)         if (&User-Name =~ /@\./)  {
(6)         if (&User-Name =~ /@\./)   -> FALSE
(6)       } # if (&User-Name)  = notfound
(6)     } # policy filter_username = notfound
(6)     [preprocess] = ok
(6) auth_log: EXPAND /usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d
(6) auth_log:    --> /usr/local/var/log/radius/radacct/127.0.0.1/auth-detail-20180821
(6) auth_log: /usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d expands to /usr/local/var/log/radius/radacct/127.0.0.1/auth-detail-20180821
(6) auth_log: EXPAND %t
(6) auth_log:    --> Tue Aug 21 19:09:39 2018
(6)     [auth_log] = ok
(6) eap: Peer sent EAP Response (code 2) ID 6 length 6
(6) eap: No EAP Start, assuming it's an on-going EAP conversation
(6)     [eap] = updated
(6) files: users: Matched entry DEFAULT at line 1
(6)     [files] = ok
(6)     [expiration] = noop
(6)     [logintime] = noop
(6)   } # authorize = updated
(6) Found Auth-Type = eap
(6) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(6)   authenticate {
(6) eap: Expiring EAP session with state 0x8db2a53288b4a858
(6) eap: Finished EAP session with state 0x8db2a53288b4a858
(6) eap: Previous EAP request found for state 0x8db2a53288b4a858, released from the list
(6) eap: Peer sent packet with method EAP TLS (13)
(6) eap: Calling submodule eap_tls to process data
(6) eap_tls: Continuing EAP-TLS
(6) eap_tls: Peer ACKed our handshake fragment.  handshake is finished
(6) eap_tls: [eaptls verify] = success
(6) eap_tls: [eaptls process] = success
(6) eap: Sending EAP Success (code 3) ID 6 length 4
(6) eap: Freeing handler
(6)     [eap] = ok
(6)   } # authenticate = ok
(6) # Executing section post-auth from file /usr/local/etc/raddb/sites-enabled/default
(6)   post-auth {
(6)     update {
(6)       No attributes updated
(6)     } # update = noop
(6) ldap: EXPAND .
(6) ldap:    --> .
(6) ldap: EXPAND Authenticated at %S
(6) ldap:    --> Authenticated at 2018-08-21 19:09:39
rlm_ldap (ldap): Reserved connection (0)
(6) ldap: EXPAND (samaccountname=%{%{Stripped-User-Name}:-%{User-Name}})
(6) ldap:    --> (samaccountname=client.pem)
(6) ldap: Performing search in "dc=Domain,dc=net" with filter "(samaccountname=client.pem)", scope "sub"
(6) ldap: Waiting for search result...
(6) ldap: ERROR: Failed performing search: Operations error with LDAP database.  Please see the LDAP server configuration / documentation for more information.
(6) ldap: ERROR: Server said: 000004DC: LdapErr: DSID-0C0907C2, comment: In order to perform this operation a successful bind must be completed on the connection., data 0, v2580.
rlm_ldap (ldap): Released connection (0)
Need 5 more connections to reach 10 spares
rlm_ldap (ldap): Opening additional connection (5), 1 of 27 pending slots used
rlm_ldap (ldap): Connecting to ldap://Domain.net:389
rlm_ldap (ldap): Waiting for bind result...
rlm_ldap (ldap): Bind successful
(6)     [ldap] = fail
(6)   } # post-auth = fail
(6) Using Post-Auth-Type Reject
(6) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(6)   Post-Auth-Type REJECT {
(6) attr_filter.access_reject: EXPAND %{User-Name}
(6) attr_filter.access_reject:    --> client.pem
(6) attr_filter.access_reject: Matched entry DEFAULT at line 11
(6)     [attr_filter.access_reject] = updated
(6)     [eap] = noop
(6)     policy remove_reply_message_if_eap {
(6)       if (&reply:EAP-Message && &reply:Reply-Message) {
(6)       if (&reply:EAP-Message && &reply:Reply-Message)  -> FALSE
(6)       else {
(6)         [noop] = noop
(6)       } # else = noop
(6)     } # policy remove_reply_message_if_eap = noop
(6)   } # Post-Auth-Type REJECT = updated
(6) Delaying response for 1.000000 seconds
Waking up in 0.3 seconds.
Waking up in 0.6 seconds.
(6) Sending delayed response
(6) Sent Access-Reject Id 6 from 127.0.0.1:1812 to 127.0.0.1:36789 length 44
(6)   EAP-Message = 0x03060004
(6)   Message-Authenticator = 0x00000000000000000000000000000000
Waking up in 3.9 seconds.
(0) Cleaning up request packet ID 0 with timestamp +4
(1) Cleaning up request packet ID 1 with timestamp +4
(2) Cleaning up request packet ID 2 with timestamp +4
(3) Cleaning up request packet ID 3 with timestamp +4
(4) Cleaning up request packet ID 4 with timestamp +4
(5) Cleaning up request packet ID 5 with timestamp +4
(6) Cleaning up request packet ID 6 with timestamp +4
Ready to process requests



From: Freeradius-Users <freeradius-users-bounces+kevin.virk=faithlife.com at lists.freeradius.org> on behalf of freeradius-users-request at lists.freeradius.org  <freeradius-users-request at lists.freeradius.org>
Sent: Tuesday, August 21, 2018 3:00 AM
To: freeradius-users at lists.freeradius.org
Subject: Freeradius-Users Digest, Vol 160, Issue 41
  
Send Freeradius-Users mailing list submissions to
freeradius-users at lists.freeradius.org

To subscribe or unsubscribe via the World Wide Web, visit
http://lists.freeradius.org/mailman/listinfo/freeradius-users
or, via email, send a message with subject or body 'help' to
freeradius-users-request at lists.freeradius.org

You can reach the person managing the list at
freeradius-users-owner at lists.freeradius.org

When replying, please edit your Subject line so it is more specific
than "Re: Contents of Freeradius-Users digest..."


Today's Topics:

1. Re: Re: Apache with mod_auth_radius starts X requests
(Fajar A. Nugraha)


----------------------------------------------------------------------

Message: 1
Date: Tue, 21 Aug 2018 16:25:50 +0700
From: "Fajar A. Nugraha" <list at fajar.net>
To: FreeRadius users mailing list
<freeradius-users at lists.freeradius.org>
Subject: Re: Re: Apache with mod_auth_radius starts X requests
Message-ID:
<CAG1y0sda1T+K+gGYotwihfd+Ly2RLkPrZd_fCt2Ciiz31q-jQQ at mail.gmail.com>
Content-Type: text/plain; charset="UTF-8"

On Tue, Aug 21, 2018 at 4:22 PM, Carsten Schulze <
carsten.schulze at leuphana.de> wrote:

> Hi,
>
> to finalize.
>
> I installed a PHP Directory Listner to that folder, with that, only one
> request was generated.
>
> If its not possible, you can reduce the index.* (checks) in apache, which
> will reduce the total amount of Radius-Reuqests.
>
> /etc/apache2/mods-enabled/dir.conf
> <IfModule mod_dir.c>
> #DirectoryIndex index.html index.cgi  index.pl index.php
> index.xhtml index.htm
> DirectoryIndex index.php
> </IfModule>
>
>
Isn't that basically what
https://github.com/FreeRADIUS/mod_auth_radius#4-some-warnings says?

-- 
Fajar


------------------------------

Subject: Digest Footer

-
List info/subscribe/unsubscribe? See  http://www.freeradius.org/list/users.html

------------------------------

End of Freeradius-Users Digest, Vol 160, Issue 41
*************************************************
   




More information about the Freeradius-Users mailing list