Access-Accept but condition isn't correct

[Marcin Romanowski]

Hello,
I'd like to check mac condition with ISG cisco.

in users file:
192.168.10.100 Cleartext-Password := "cisco", *Calling-Station-Id :=
"00:50:79:66:68:01"*
               Cisco-Service-info = "QU;200000;D;600000",
                            Cisco-Avpair +=
'subscriber:accounting-list=BRAS',
               Cisco-Avpair += 'subscriber:keepalive=interval 10',
               Cisco-Avpair += 'subscriber:idle-timeout-direction=inbound'

debug:

(0) Received Access-Request Id 60 from 1.1.1.3:1645 to 1.1.1.2:1812 length
135
(0)   User-Name = "192.168.10.100"
(0)   User-Password = "cisco"
(0)   Framed-IP-Address = 192.168.10.100
(0)   *Calling-Station-Id = "00:50:79:66:68:00"*
(0)   NAS-Port-Type = Virtual
(0)   NAS-Port = 0
(0)   NAS-Port-Id = "0/0/0/0"
(0)   Service-Type = Outbound-User
(0)   NAS-IP-Address = 1.1.1.3
(0)   Acct-Session-Id = "00000FDE"
(0)   NAS-Identifier = "ASR_1"
(0)   Event-Timestamp = "Jan 26 2020 18:54:55 UTC"
(0) # Executing section authorize from file
/etc/freeradius/3.0/sites-enabled/default
(0)   authorize {
(0)     policy filter_username {
(0)       if (&User-Name) {
(0)       if (&User-Name)  -> TRUE
(0)       if (&User-Name)  {
(0)         if (&User-Name =~ / /) {
(0)         if (&User-Name =~ / /)  -> FALSE
(0)         if (&User-Name =~ /@[^@]*@/ ) {
(0)         if (&User-Name =~ /@[^@]*@/ )  -> FALSE
(0)         if (&User-Name =~ /\.\./ ) {
(0)         if (&User-Name =~ /\.\./ )  -> FALSE
(0)         if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/))  {
(0)         if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/))   ->
FALSE
(0)         if (&User-Name =~ /\.$/)  {
(0)         if (&User-Name =~ /\.$/)   -> FALSE
(0)         if (&User-Name =~ /@\./)  {
(0)         if (&User-Name =~ /@\./)   -> FALSE
(0)       } # if (&User-Name)  = notfound
(0)     } # policy filter_username = notfound
(0)     [preprocess] = ok
(0)     [chap] = noop
(0)     [mschap] = noop
(0)     [digest] = noop
(0) suffix: Checking for suffix after "@"
(0) suffix: No '@' in User-Name = "192.168.10.100", looking up realm NULL
(0) suffix: No such realm "NULL"
(0)     [suffix] = noop
(0) eap: No EAP-Message, not doing EAP
(0)     [eap] = noop
(0) files: users: Matched entry 192.168.10.100 at line 37
(0)     [files] = ok
(0)     [expiration] = noop
(0)     [logintime] = noop
(0)     [pap] = updated
(0)   } # authorize = updated
(0) Found Auth-Type = PAP
(0) # Executing group from file /etc/freeradius/3.0/sites-enabled/default
(0)   Auth-Type PAP {
(0) pap: Login attempt with password
(0) pap: Comparing with "known good" Cleartext-Password
(0) pap: User authenticated successfully
(0)     [pap] = ok
(0)   } # Auth-Type PAP = ok
(0) # Executing section post-auth from file
/etc/freeradius/3.0/sites-enabled/default
(0)   post-auth {
(0)     update {
(0)       No attributes updated
(0)     } # update = noop
(0)     [exec] = noop
(0)     policy remove_reply_message_if_eap {
(0)       if (&reply:EAP-Message && &reply:Reply-Message) {
(0)       if (&reply:EAP-Message && &reply:Reply-Message)  -> FALSE
(0)       else {
(0)         [noop] = noop
(0)       } # else = noop
(0)     } # policy remove_reply_message_if_eap = noop
(0)   } # post-auth = noop
(0) Sent Access-Accept Id 60 from 1.1.1.2:1812 to 1.1.1.3:1645 length 0
(0)   Cisco-Service-Info = "QU;200000;D;600000"
(0)   Cisco-AVPair = "subscriber:accounting-list=BRAS"
(0)   Cisco-AVPair = "subscriber:keepalive=interval 10"
(0)   Cisco-AVPair = "subscriber:idle-timeout-direction=inbound"
(0) Finished request

Calling-Station-Id is different than in config but i get Access-Accept.

Where I'm doing wrong?

Best Regards
Marcin