Hi, i have trouble, dialing out with a lucent max1800 isdn router, using freeradius under sles9. Here is an extract of the users file: <<< user-in Password == "xxx" Service-Type == Framed-User, Framed-Protocol = ASCEND-MPP, Framed-Address = yyy.yyy.yyy.yyy, Framed-Netmask = zzz.zzz.zzz.zzz, Framed-Route = None user-out Password == "xxxx", Service-Type == Dialout-Framed-User User-Name = "user", Ascend-Send-Auth = Send-Auth-CHAP, Ascend-Send-Secret = "xxxx", Ascend-Dial-Number = 0123456789, Ascend-Data-Svc = Nailed-64K, Framed-Protocol = ASCEND-MPP, Framed-Address = yyy.yyy.yyy.yyy., Framed-Netmask = zzz.zzz.zzz.zzz, Ascend-Expect-Callback = Expect-Callback-Yes, Ascend-Idle-Limit = 300
With this config, dialing in is no problem and works fine. But dialing out with callback doesn't work. The call goes out and is terminated without any call back. I'm running freeradius in debug mode an getting the following output: <<< rad_recv: Access-Request packet from host xxx.xxx.xxx.xxx:1025, id=145, length=67 User-Name = "user-out" User-Password = "xxx" NAS-IP-Address = yyy.yyy.yyy.yyy NAS-Port = 0 NAS-Port-Type = Virtual Service-Type = Outbound-User State = 0x Processing the authorize section of radiusd.conf Processing the authorize section of radiusd.conf modcall: entering group authorize for request 0 modcall[authorize]: module "preprocess" returns ok for request 0 radius_xlat: '/var/log/radius/radacct/xxx.xxx.xxx.xxx/auth-detail-20061204' rlm_detail: /var/log/radius/radacct/%{Client-IP-Address}/auth-detail-%Y%m%d expands to /var/log/radius/radacct/xxx.xxx.xxx.xxx/auth-detail-20061204 modcall[authorize]: module "auth_log" returns ok for request 0 modcall[authorize]: module "chap" returns noop for request 0 modcall[authorize]: module "mschap" returns noop for request 0 rlm_realm: No '@' in User-Name = "cxdmg-out", looking up realm NULL rlm_realm: No such realm "NULL" modcall[authorize]: module "suffix" returns noop for request 0 rlm_eap: No EAP-Message, not doing EAP modcall[authorize]: module "eap" returns noop for request 0 users: Matched entry cxdmg-out at line 1291 modcall[authorize]: module "files" returns ok for request 0 modcall: group authorize returns ok for request 0 auth: type Local auth: user supplied User-Password matches local User-Password Processing the post-auth section of radiusd.conf modcall: entering group post-auth for request 0 radius_xlat: '/var/log/radius/radacct/xxx.xxx.xxx.xxx/reply-detail-20061204' rlm_detail: /var/log/radius/radacct/%{Client-IP-Address}/reply-detail-%Y%m%d expands to /var/log/radius/radacct/xxx.xxx.xxx.xxx/reply-detail-20061204 modcall[post-auth]: module "reply_log" returns ok for request 0 modcall: group post-auth returns ok for request 0 Sending Access-Accept of id 145 to xxx.xxx.xxx.xxx:1025 User-Name = "user" Ascend-Send-Auth = Send-Auth-CHAP Ascend-Send-Secret = "9" Ascend-Dial-Number = "0123456789" Ascend-Data-Svc = Nailed-64K Framed-Protocol = Ascend-MPP Framed-Address = yyy.yyy.yyy.yyy Framed-Netmask = zzz.zzz.zzz.zzz Ascend-Expect-Callback = Expect-Callback-Yes Ascend-Idle-Limit = 300 Finished request 0 Going to the next request
I dont't see any errors. The lucent retries several times and then gives up. As you can see, I allready includes the dictionary.ascend. Without any success. I also switched between OLD and VSA on the lucent and the freeradius. But without success. Are there any issues, between lucent and freeradius? Ore are there any errors in the config? Thanks in advance. Kind Regards, Andreas