Hi Alan,
Read doc/Simultaneous-Use. It's a how-to, and most questions are answered there.
Thank you.. I will re-read the Simultaneous-Use Doc again.. I may have to start from a simple configuration, before trying to integrate that with e-Directory.
Ugh. Upgrade to 2.1.10. I'll upgrade to 2.1.10 prior to trying again.
Those look like MAC addresses, perhaps. And that doesn't matter, if you're trying to do Simultaneous-Use for use "ziggy".
Those are not MAC addresses.. They are randomly generated numbers? Why? don't know.. But it doesn't matter I guess. Just makes it hard for me to understand the debug log, since I'm new at it.
Do you get Accounting-Request packets for user "ziggy"? If not, then Simultaneous-Use will be hard to do.
I looked at the debug log again using the http://networkradius.com/freeradius.html debugging output URL (wish I found it sooner). I see Access-Request packets with "Ziggy" from Packets 3-12 for the authentication portion. The next time I see anything with Username = "Ziggy" is the Accounting-Request packet when I disconnect from the SSID as indicated in the Acct-Status-Type = Stop. In this packet, the calling-station-ID becomes 0.0.0.0. though.. Is that how it is suppose to look? Since it should be "00-22-fa-a1-ba-e8" ? rad_recv: Accounting-Request packet from host 10.32.156.5 port 32768, id=111, length=188 User-Name = "ziggy" NAS-Port = 29 NAS-IP-Address = 10.32.156.5 NAS-Identifier = "CW32CE0A" Airespace-Wlan-Id = 3 Acct-Session-Id = "4defbab6/00:22:fa:a1:ba:e8/12404" Acct-Authentic = RADIUS Tunnel-Type:0 = VLAN Tunnel-Medium-Type:0 = IEEE-802 Tunnel-Private-Group-Id:0 = "342" Acct-Status-Type = Stop Acct-Input-Octets = 68833 Acct-Output-Octets = 9551 Acct-Input-Packets = 559 Acct-Output-Packets = 47 Acct-Terminate-Cause = User-Request Acct-Session-Time = 117 Acct-Delay-Time = 0 Calling-Station-Id = "0.0.0.0" Called-Station-Id = "10.32.156.5" On Thu, Jun 9, 2011 at 8:19 PM, Alan DeKok <aland@deployingradius.com> wrote:
Ziggy Bopster wrote:
I am want to enable Simultaneous-Use for our users. I have been stuck for many many days trying to figure this out, any help is greatly appreciated. This is my first time posting, so sorry if my netiquette is not correct
Read doc/Simultaneous-Use. It's a how-to, and most questions are answered there.
I. Configuration of System: FreeRADIUS Version 2.1.1, built on May 9 2010 at 12:09:29
Ugh. Upgrade to 2.1.10.
III. Problem: In looking at the debug logs, randomly generated UserName Accounting-Request packets are being sent from the NAS to the FreeRADIUS, before and after the successful authentication of the UserName (ziggy) using the EAP-PEAP-MSCHAPV2 protocol (during which time the correct UserName is sent by NAS).
Those look like MAC addresses, perhaps. And that doesn't matter, if you're trying to do Simultaneous-Use for use "ziggy".
Do you get Accounting-Request packets for user "ziggy"? If not, then Simultaneous-Use will be hard to do.
Alan DeKok. - List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html