With the following setup to use eap-tls,do i need to enable mschap? i have noticed that mschap is enabled as indicated in this document http://www.tldp.org/HOWTO/8021X-HOWTO/. Fedora core 3 FreeRadius 1.0.4 openssl .098 Dell TrueMobile 1170 Access Pointv2.3.3 802.11b/g cards for AP and supplicant Windows XP SP2 also i have attached my radiusd.conf, eap.conf and output of radius in debug mode...i would appreciate if you guys can take a look at it and see if i am missing anything. your help is very much appreciated ! thanks.... the problem is that the radius is not receiving any requests from the client! Hamid. radiusd.conf: ## ## radiusd.conf -- FreeRADIUS server configuration file. ## ## http://www.freeradius.org/ ## $Id: radiusd.conf.in,v 1.188.2.3 2005/02/07 19:52:05 aland Exp $ ## # The location of other config files and # logfiles are declared in this file # # Also general configuration for modules can be done # in this file, it is exported through the API to # modules that ask for it. # # The configuration variables defined here are of the form ${foo} # They are local to this file, and do not change from request to # request. # # The per-request variables are of the form %{Attribute-Name}, and # are taken from the values of the attribute in the incoming # request. See 'doc/variables.txt' for more information. prefix = /opt/radiusd exec_prefix = ${prefix} sysconfdir = ${prefix}/etc localstatedir = ${prefix}/var sbindir = ${exec_prefix}/sbin logdir = ${localstatedir}/log/radius raddbdir = ${sysconfdir}/raddb radacctdir = ${logdir}/radacct # Location of config and logfiles. confdir = ${raddbdir} run_dir = ${localstatedir}/run/radiusd # # The logging messages for the server are appended to the # tail of this file. # log_file = ${logdir}/radius.log # # libdir: Where to find the rlm_* modules. # # This should be automatically set at configuration time. # # If the server builds and installs, but fails at execution time # with an 'undefined symbol' error, then you can use the libdir # directive to work around the problem. # # The cause is usually that a library has been installed on your # system in a place where the dynamic linker CANNOT find it. When # executing as root (or another user), your personal environment MAY # be set up to allow the dynamic linker to find the library. When # executing as a daemon, FreeRADIUS MAY NOT have the same # personalized configuration. # # To work around the problem, find out which library contains that symbol, # and add the directory containing that library to the end of 'libdir', # with a colon separating the directory names. NO spaces are allowed. # # e.g. libdir = /usr/local/lib:/opt/package/lib # # You can also try setting the LD_LIBRARY_PATH environment variable # in a script which starts the server. # # If that does not work, then you can re-configure and re-build the # server to NOT use shared libraries, via: # # ./configure --disable-shared # make # make install # libdir = ${exec_prefix}/lib # pidfile: Where to place the PID of the RADIUS server. # # The server may be signalled while it's running by using this # file. # # This file is written when ONLY running in daemon mode. # # e.g.: kill -HUP `cat /var/run/radiusd/radiusd.pid` # pidfile = ${run_dir}/radiusd.pid # user/group: The name (or #number) of the user/group to run radiusd as. # # If these are commented out, the server will run as the user/group # that started it. In order to change to a different user/group, you # MUST be root ( or have root privleges ) to start the server. # # We STRONGLY recommend that you run the server with as few permissions # as possible. That is, if you're not using shadow passwords, the # user and group items below should be set to 'nobody'. # # On SCO (ODT 3) use "user = nouser" and "group = nogroup". # # NOTE that some kernels refuse to setgid(group) when the value of # (unsigned)group is above 60000; don't use group nobody on these systems! # # On systems with shadow passwords, you might have to set 'group = shadow' # for the server to be able to read the shadow password file. If you can # authenticate users while in debug mode, but not in daemon mode, it may be # that the debugging mode server is running as a user that can read the # shadow info, and the user listed below can not. # #user = nobody #group = nobody # max_request_time: The maximum time (in seconds) to handle a request. # # Requests which take more time than this to process may be killed, and # a REJECT message is returned. # # WARNING: If you notice that requests take a long time to be handled, # then this MAY INDICATE a bug in the server, in one of the modules # used to handle a request, OR in your local configuration. # # This problem is most often seen when using an SQL database. If it takes # more than a second or two to receive an answer from the SQL database, # then it probably means that you haven't indexed the database. See your # SQL server documentation for more information. # # Useful range of values: 5 to 120 # max_request_time = 30 # delete_blocked_requests: If the request takes MORE THAN 'max_request_time' # to be handled, then maybe the server should delete it. # # If you're running in threaded, or thread pool mode, this setting # should probably be 'no'. Setting it to 'yes' when using a threaded # server MAY cause the server to crash! # delete_blocked_requests = no # cleanup_delay: The time to wait (in seconds) before cleaning up # a reply which was sent to the NAS. # # The RADIUS request is normally cached internally for a short period # of time, after the reply is sent to the NAS. The reply packet may be # lost in the network, and the NAS will not see it. The NAS will then # re-send the request, and the server will respond quickly with the # cached reply. # # If this value is set too low, then duplicate requests from the NAS # MAY NOT be detected, and will instead be handled as seperate requests. # # If this value is set too high, then the server will cache too many # requests, and some new requests may get blocked. (See 'max_requests'.) # # Useful range of values: 2 to 10 # cleanup_delay = 5 # max_requests: The maximum number of requests which the server keeps # track of. This should be 256 multiplied by the number of clients. # e.g. With 4 clients, this number should be 1024. # # If this number is too low, then when the server becomes busy, # it will not respond to any new requests, until the 'cleanup_delay' # time has passed, and it has removed the old requests. # # If this number is set too high, then the server will use a bit more # memory for no real benefit. # # If you aren't sure what it should be set to, it's better to set it # too high than too low. Setting it to 1000 per client is probably # the highest it should be. # # Useful range of values: 256 to infinity # max_requests = 1024 # bind_address: Make the server listen on a particular IP address, and # send replies out from that address. This directive is most useful # for machines with multiple IP addresses on one interface. # # It can either contain "*", or an IP address, or a fully qualified # Internet domain name. The default is "*" # # As of 1.0, you can also use the "listen" directive. See below for # more information. # bind_address = radiusd.ece.neu.edu # port: Allows you to bind FreeRADIUS to a specific port. # # The default port that most NAS boxes use is 1645, which is historical. # RFC 2138 defines 1812 to be the new port. Many new servers and # NAS boxes use 1812, which can create interoperability problems. # # The port is defined here to be 0 so that the server will pick up # the machine's local configuration for the radius port, as defined # in /etc/services. # # If you want to use the default RADIUS port as defined on your server, # (usually through 'grep radius /etc/services') set this to 0 (zero). # # A port given on the command-line via '-p' over-rides this one. # # As of 1.0, you can also use the "listen" directive. See below for # more information. # port = 0 # # By default, the server uses "bind_address" to listen to all IP's # on a machine, or just one IP. The "port" configuration is used # to select the authentication port used when listening on those # addresses. # # If you want the server to listen on additional addresses, you can # use the "listen" section. A sample section (commented out) is included # below. This "listen" section duplicates the functionality of the # "bind_address" and "port" configuration entries, but it only listens # for authentication packets. # # If you comment out the "bind_address" and "port" configuration entries, # then it becomes possible to make the server accept only accounting, # or authentication packets. Previously, it always listened for both # types of packets, and it was impossible to make it listen for only # one type of packet. # #listen { # IP address on which to listen. # Allowed values are: # dotted quad (1.2.3.4) # hostname (radius.example.com) # wildcard (*) # ipaddr = * # Port on which to listen. # Allowed values are: # integer port number (1812) # 0 means "use /etc/services for the proper port" # port = 0 # Type of packets to listen for. # Allowed values are: # auth listen for authentication packets # acct listen for accounting packets # # type = auth #} # hostname_lookups: Log the names of clients or just their IP addresses # e.g., www.freeradius.org (on) or 206.47.27.232 (off). # # The default is 'off' because it would be overall better for the net # if people had to knowingly turn this feature on, since enabling it # means that each client request will result in AT LEAST one lookup # request to the nameserver. Enabling hostname_lookups will also # mean that your server may stop randomly for 30 seconds from time # to time, if the DNS requests take too long. # # Turning hostname lookups off also means that the server won't block # for 30 seconds, if it sees an IP address which has no name associated # with it. # # allowed values: {no, yes} # hostname_lookups = no # Core dumps are a bad thing. This should only be set to 'yes' # if you're debugging a problem with the server. # # allowed values: {no, yes} # allow_core_dumps = no # Regular expressions # # These items are set at configure time. If they're set to "yes", # then setting them to "no" turns off regular expression support. # # If they're set to "no" at configure time, then setting them to "yes" # WILL NOT WORK. It will give you an error. # regular_expressions = yes extended_expressions = yes # Log the full User-Name attribute, as it was found in the request. # # allowed values: {no, yes} # log_stripped_names = no # Log authentication requests to the log file. # # allowed values: {no, yes} # log_auth = yes # Log passwords with the authentication requests. # log_auth_badpass - logs password if it's rejected # log_auth_goodpass - logs password if it's correct # # allowed values: {no, yes} # log_auth_badpass = yes log_auth_goodpass = yes # usercollide: Turn "username collision" code on and off. See the # "doc/duplicate-users" file # # WARNING # !!!!!!! Setting this to "yes" may result in the server behaving # !!!!!!! strangely. The "username collision" code will ONLY work # !!!!!!! with clear-text passwords. Even then, it may not do what # !!!!!!! you want, or what you expect. # !!!!!!! # !!!!!!! We STRONGLY RECOMMEND that you do not use this feature, # !!!!!!! and that you find another way of acheiving the same goal. # !!!!!!! # !!!!!!! e,g. module fail-over. See 'doc/configurable_failover' # WARNING # usercollide = no # lower_user / lower_pass: # Lower case the username/password "before" or "after" # attempting to authenticate. # # If "before", the server will first modify the request and then try # to auth the user. If "after", the server will first auth using the # values provided by the user. If that fails it will reprocess the # request after modifying it as you specify below. # # This is as close as we can get to case insensitivity. It is the # admin's job to ensure that the username on the auth db side is # *also* lowercase to make this work # # Default is 'no' (don't lowercase values) # Valid values = "before" / "after" / "no" # lower_user = no lower_pass = no # nospace_user / nospace_pass: # # Some users like to enter spaces in their username or password # incorrectly. To save yourself the tech support call, you can # eliminate those spaces here: # # Default is 'no' (don't remove spaces) # Valid values = "before" / "after" / "no" (explanation above) # nospace_user = no nospace_pass = no # The program to execute to do concurrency checks. checkrad = ${sbindir}/checkrad # SECURITY CONFIGURATION # # There may be multiple methods of attacking on the server. This # section holds the configuration items which minimize the impact # of those attacks # security { # # max_attributes: The maximum number of attributes # permitted in a RADIUS packet. Packets which have MORE # than this number of attributes in them will be dropped. # # If this number is set too low, then no RADIUS packets # will be accepted. # # If this number is set too high, then an attacker may be # able to send a small number of packets which will cause # the server to use all available memory on the machine. # # Setting this number to 0 means "allow any number of attributes" max_attributes = 200 # # delayed_reject: When sending an Access-Reject, it can be # delayed for a few seconds. This may help slow down a DoS # attack. It also helps to slow down people trying to brute-force # crack a users password. # # Setting this number to 0 means "send rejects immediately" # # If this number is set higher than 'cleanup_delay', then the # rejects will be sent at 'cleanup_delay' time, when the request # is deleted from the internal cache of requests. # # Useful ranges: 1 to 5 reject_delay = 1 # # status_server: Whether or not the server will respond # to Status-Server requests. # # Normally this should be set to "no", because they're useless. # See: http://www.freeradius.org/rfc/rfc2865.html#Keep-Alives # # However, certain NAS boxes may require them. # # When sent a Status-Server message, the server responds with # an Access-Accept packet, containing a Reply-Message attribute, # which is a string describing how long the server has been # running. # status_server = no } # PROXY CONFIGURATION # # proxy_requests: Turns proxying of RADIUS requests on or off. # # The server has proxying turned on by default. If your system is NOT # set up to proxy requests to another server, then you can turn proxying # off here. This will save a small amount of resources on the server. # # If you have proxying turned off, and your configuration files say # to proxy a request, then an error message will be logged. # # To disable proxying, change the "yes" to "no", and comment the # $INCLUDE line. # # allowed values: {no, yes} # proxy_requests = no #$INCLUDE ${confdir}/proxy.conf # CLIENTS CONFIGURATION # # Client configuration is defined in "clients.conf". # # The 'clients.conf' file contains all of the information from the old # 'clients' and 'naslist' configuration files. We recommend that you # do NOT use 'client's or 'naslist', although they are still # supported. # # Anything listed in 'clients.conf' will take precedence over the # information from the old-style configuration files. # $INCLUDE ${confdir}/clients.conf # SNMP CONFIGURATION # # Snmp configuration is only valid if SNMP support was enabled # at compile time. # # To enable SNMP querying of the server, set the value of the # 'snmp' attribute to 'yes' # snmp = no $INCLUDE ${confdir}/snmp.conf # THREAD POOL CONFIGURATION # # The thread pool is a long-lived group of threads which # take turns (round-robin) handling any incoming requests. # # You probably want to have a few spare threads around, # so that high-load situations can be handled immediately. If you # don't have any spare threads, then the request handling will # be delayed while a new thread is created, and added to the pool. # # You probably don't want too many spare threads around, # otherwise they'll be sitting there taking up resources, and # not doing anything productive. # # The numbers given below should be adequate for most situations. # thread pool { # Number of servers to start initially --- should be a reasonable # ballpark figure. start_servers = 5 # Limit on the total number of servers running. # # If this limit is ever reached, clients will be LOCKED OUT, so it # should NOT BE SET TOO LOW. It is intended mainly as a brake to # keep a runaway server from taking the system with it as it spirals # down... # # You may find that the server is regularly reaching the # 'max_servers' number of threads, and that increasing # 'max_servers' doesn't seem to make much difference. # # If this is the case, then the problem is MOST LIKELY that # your back-end databases are taking too long to respond, and # are preventing the server from responding in a timely manner. # # The solution is NOT do keep increasing the 'max_servers' # value, but instead to fix the underlying cause of the # problem: slow database, or 'hostname_lookups=yes'. # # For more information, see 'max_request_time', above. # max_servers = 32 # Server-pool size regulation. Rather than making you guess # how many servers you need, FreeRADIUS dynamically adapts to # the load it sees, that is, it tries to maintain enough # servers to handle the current load, plus a few spare # servers to handle transient load spikes. # # It does this by periodically checking how many servers are # waiting for a request. If there are fewer than # min_spare_servers, it creates a new spare. If there are # more than max_spare_servers, some of the spares die off. # The default values are probably OK for most sites. # min_spare_servers = 3 max_spare_servers = 10 # There may be memory leaks or resource allocation problems with # the server. If so, set this value to 300 or so, so that the # resources will be cleaned up periodically. # # This should only be necessary if there are serious bugs in the # server which have not yet been fixed. # # '0' is a special value meaning 'infinity', or 'the servers never # exit' max_requests_per_server = 0 } # MODULE CONFIGURATION # # The names and configuration of each module is located in this section. # # After the modules are defined here, they may be referred to by name, # in other sections of this configuration file. # modules { # # Each module has a configuration as follows: # # name [ instance ] { # config_item = value # ... # } # # The 'name' is used to load the 'rlm_name' library # which implements the functionality of the module. # # The 'instance' is optional. To have two different instances # of a module, it first must be referred to by 'name'. # The different copies of the module are then created by # inventing two 'instance' names, e.g. 'instance1' and 'instance2' # # The instance names can then be used in later configuration # INSTEAD of the original 'name'. See the 'radutmp' configuration # below for an example. # # PAP module to authenticate users based on their stored password # # Supports multiple encryption schemes # clear: Clear text # crypt: Unix crypt # md5: MD5 ecnryption # sha1: SHA1 encryption. # DEFAULT: crypt #pap { # encryption_scheme = crypt #} # CHAP module # # To authenticate requests containing a CHAP-Password attribute. # #chap { # authtype = CHAP #} # Pluggable Authentication Modules # # For Linux, see: # http://www.kernel.org/pub/linux/libs/pam/index.html # # WARNING: On many systems, the system PAM libraries have # memory leaks! We STRONGLY SUGGEST that you do not # use PAM for authentication, due to those memory leaks. # #pam { # # The name to use for PAM authentication. # PAM looks in /etc/pam.d/${pam_auth_name} # for it's configuration. See 'redhat/radiusd-pam' # for a sample PAM configuration file. # # Note that any Pam-Auth attribute set in the 'authorize' # section will over-ride this one. # # pam_auth = radiusd #} # Unix /etc/passwd style authentication # unix { # # Cache /etc/passwd, /etc/shadow, and /etc/group # # The default is to NOT cache them. # # For FreeBSD and NetBSD, you do NOT want to enable # the cache, as it's password lookups are done via a # database, so set this value to 'no'. # # Some systems (e.g. RedHat Linux with pam_pwbd) can # take *seconds* to check a password, when th passwd # file containing 1000's of entries. For those systems, # you should set the cache value to 'yes', and set # the locations of the 'passwd', 'shadow', and 'group' # files, below. # # allowed values: {no, yes} cache = no # Reload the cache every 600 seconds (10mins). 0 to disable. cache_reload = 600 # # Define the locations of the normal passwd, shadow, and # group files. # # 'shadow' is commented out by default, because not all # systems have shadow passwords. # # To force the module to use the system password functions, # instead of reading the files, leave the following entries # commented out. # # This is required for some systems, like FreeBSD, # and Mac OSX. # # passwd = /etc/passwd # shadow = /etc/shadow # group = /etc/group # # The location of the "wtmp" file. # This should be moved to it's own module soon. # # The only use for 'radlast'. If you don't use # 'radlast', then you can comment out this item. # radwtmp = ${logdir}/radwtmp } # Extensible Authentication Protocol # # For all EAP related authentications. # Now in another file, because it is very large. # $INCLUDE ${confdir}/eap.conf # Microsoft CHAP authentication # # This module supports MS-CHAP and MS-CHAPv2 authentication. # It also enforces the SMB-Account-Ctrl attribute. # #mschap { # # As of 0.9, the mschap module does NOT support # reading from /etc/smbpasswd. # # If you are using /etc/smbpasswd, see the 'passwd' # module for an example of how to use /etc/smbpasswd # authtype value, if present, will be used # to overwrite (or add) Auth-Type during # authorization. Normally should be MS-CHAP # authtype = MS-CHAP # if use_mppe is not set to no mschap will # add MS-CHAP-MPPE-Keys for MS-CHAPv1 and # MS-MPPE-Recv-Key/MS-MPPE-Send-Key for MS-CHAPv2 # #use_mppe = no # if mppe is enabled require_encryption makes # encryption moderate # #require_encryption = yes # require_strong always requires 128 bit key # encryption # #require_strong = yes # Windows sends us a username in the form of # DOMAIN\user, but sends the challenge response # based on only the user portion. This hack # corrects for that incorrect behavior. # #with_ntdomain_hack = no # The module can perform authentication itself, OR # use a Windows Domain Controller. This configuration # directive tells the module to call the ntlm_auth # program, which will do the authentication, and return # the NT-Key. Note that you MUST have "winbindd" and # "nmbd" running on the local machine for ntlm_auth # to work. See the ntlm_auth program documentation # for details. # # Be VERY careful when editing the following line! # #ntlm_auth = "/path/to/ntlm_auth --request-nt-key --username=%{Stripped-User-Name:-%{User-Name:-None}} --challenge=%{mschap:Challenge:-00} --nt-response=%{mschap:NT-Response:-00}" #} # Lightweight Directory Access Protocol (LDAP) # # This module definition allows you to use LDAP for # authorization and authentication (Auth-Type := LDAP) # # See doc/rlm_ldap for description of configuration options # and sample authorize{} and authenticate{} blocks #ldap { # server = "ldap.your.domain" # identity = "cn=admin,o=My Org,c=UA" # password = mypass #basedn = "o=My Org,c=UA" #filter = "(uid=%{Stripped-User-Name:-%{User-Name}})" # base_filter = "(objectclass=radiusprofile)" # set this to 'yes' to use TLS encrypted connections # to the LDAP database by using the StartTLS extended # operation. # The StartTLS operation is supposed to be used with normal # ldap connections instead of using ldaps (port 689) connections #start_tls = no # tls_cacertfile = /path/to/cacert.pem # tls_cacertdir = /path/to/ca/dir/ # tls_certfile = /path/to/radius.crt # tls_keyfile = /path/to/radius.key # tls_randfile = /path/to/rnd # tls_require_cert = "demand" # default_profile = "cn=radprofile,ou=dialup,o=My Org,c=UA" # profile_attribute = "radiusProfileDn" #access_attr = "dialupAccess" # Mapping of RADIUS dictionary attributes to LDAP # directory attributes. #dictionary_mapping = ${raddbdir}/ldap.attrmap #ldap_connections_number = 5 # # NOTICE: The password_header directive is NOT case insensitive # # password_header = "{clear}" # # Set: # password_attribute = nspmPassword # # to get the user's password from a Novell eDirectory # backend. This will work *only if* freeRADIUS is # configured to build with --with-edir option. # # # The server can usually figure this out on its own, and pull # the correct User-Password or NT-Password from the database. # # Note that NT-Passwords MUST be stored as a 32-digit hex # string, and MUST start off with "0x", such as: # # 0x000102030405060708090a0b0c0d0e0f # # Without the leading "0x", NT-Passwords will not work. # This goes for NT-Passwords stored in SQL, too. # # password_attribute = userPassword # # Un-comment the following to disable Novell eDirectory account # policy check and intruder detection. This will work *only if* # FreeRADIUS is configured to build with --with-edir option. # # edir_account_policy_check=no # # groupname_attribute = cn # groupmembership_filter = "(|(&(objectClass=GroupOfNames)(member=%{Ldap-UserDn}))(&(objectClass=Gr oupOfUniqueNames)(uniquemember=%{Ldap-UserDn})))" # groupmembership_attribute = radiusGroupName #timeout = 4 #timelimit = 3 #net_timeout = 1 # compare_check_items = yes # do_xlat = yes # access_attr_used_for_allow = yes #} # passwd module allows to do authorization via any passwd-like # file and to extract any attributes from these modules # # parameters are: # filename - path to filename # format - format for filename record. This parameters # correlates record in the passwd file and RADIUS # attributes. # # Field marked as '*' is key field. That is, the parameter # with this name from the request is used to search for # the record from passwd file # Attribute marked as '=' is added to reply_itmes instead # of default configure_itmes # Attribute marked as '~' is added to request_items # # Field marked as ',' may contain a comma separated list # of attributes. # authtype - if record found this Auth-Type is used to authenticate # user # hashsize - hashtable size. If 0 or not specified records are not # stored in memory and file is red on every request. # allowmultiplekeys - if few records for every key are allowed # ignorenislike - ignore NIS-related records # delimiter - symbol to use as a field separator in passwd file, # for format ':' symbol is always used. '\0', '\n' are # not allowed # # An example configuration for using /etc/smbpasswd. # #passwd etc_smbpasswd { # filename = /etc/smbpasswd # format = "*User-Name::LM-Password:NT-Password:SMB-Account-CTRL-TEXT::" # authtype = MS-CHAP # hashsize = 100 # ignorenislike = no # allowmultiplekeys = no #} # Similar configuration, for the /etc/group file. Adds a Group-Name # attribute for every group that the user is member of. # #passwd etc_group { # filename = /etc/group # format = "=Group-Name:::*,User-Name" # hashsize = 50 # ignorenislike = yes # allowmultiplekeys = yes # delimiter = ":" #} # Realm module, for proxying. # # You can have multiple instances of the realm module to # support multiple realm syntaxs at the same time. The # search order is defined by the order in the authorize and # preacct sections. # # Four config options: # format - must be 'prefix' or 'suffix' # delimiter - must be a single character # ignore_default - set to 'yes' or 'no' # ignore_null - set to 'yes' or 'no' # # ignore_default and ignore_null can be set to 'yes' to prevent # the module from matching against DEFAULT or NULL realms. This # may be useful if you have have multiple instances of the # realm module. # # They both default to 'no'. # # 'realm/username' # # Using this entry, IPASS users have their realm set to "IPASS". realm IPASS { format = prefix delimiter = "/" ignore_default = no ignore_null = no } # 'username@realm' # realm suffix { format = suffix delimiter = "@" ignore_default = no ignore_null = no } # 'username%realm' # realm realmpercent { format = suffix delimiter = "%" ignore_default = no ignore_null = no } # # 'domain\user' # realm ntdomain { format = prefix delimiter = "\\" ignore_default = no ignore_null = no } # A simple value checking module # # It can be used to check if an attribute value in the request # matches a (possibly multi valued) attribute in the check # items This can be used for example for caller-id # authentication. For the module to run, both the request # attribute and the check items attribute must exist # # i.e. # A user has an ldap entry with 2 radiusCallingStationId # attributes with values "12345678" and "12345679". If we # enable rlm_checkval, then any request which contains a # Calling-Station-Id with one of those two values will be # accepted. Requests with other values for # Calling-Station-Id will be rejected. # # Regular expressions in the check attribute value are allowed # as long as the operator is '=~' # #checkval { # The attribute to look for in the request # item-name = Calling-Station-Id # The attribute to look for in check items. Can be multi valued # check-name = Calling-Station-Id # The data type. Can be # string,integer,ipaddr,date,abinary,octets # data-type = string # If set to yes and we dont find the item-name attribute in the # request then we send back a reject # DEFAULT is no #notfound-reject = no #} # rewrite arbitrary packets. Useful in accounting and authorization. # # # The module can also use the Rewrite-Rule attribute. If it # is set and matches the name of the module instance, then # that module instance will be the only one which runs. # # Also if new_attribute is set to yes then a new attribute # will be created containing the value replacewith and it # will be added to searchin (packet, reply, proxy, proxy_reply or config). # searchfor,ignore_case and max_matches will be ignored in that case. # # Backreferences are supported: %{0} will contain the string the whole match # and %{1} to %{8} will contain the contents of the 1st to the 8th parentheses # # If max_matches is greater than one the backreferences will correspond to the # first match # #attr_rewrite sanecallerid { # attribute = Called-Station-Id # may be "packet", "reply", "proxy", "proxy_reply" or "config" # searchin = packet # searchfor = "[+ ]" # replacewith = "" # ignore_case = no # new_attribute = no # max_matches = 10 # ## If set to yes then the replace string will be appended to the original string # append = no #} # Preprocess the incoming RADIUS request, before handing it off # to other modules. # # This module processes the 'huntgroups' and 'hints' files. # In addition, it re-writes some weird attributes created # by some NASes, and converts the attributes into a form which # is a little more standard. # preprocess { huntgroups = ${confdir}/huntgroups hints = ${confdir}/hints # This hack changes Ascend's wierd port numberings # to standard 0-??? port numbers so that the "+" works # for IP address assignments. with_ascend_hack = no ascend_channels_per_line = 23 # Windows NT machines often authenticate themselves as # NT_DOMAIN\username # # If this is set to 'yes', then the NT_DOMAIN portion # of the user-name is silently discarded. # # This configuration entry SHOULD NOT be used. # See the "realms" module for a better way to handle # NT domains. with_ntdomain_hack = no # Specialix Jetstream 8500 24 port access server. # # If the user name is 10 characters or longer, a "/" # and the excess characters after the 10th are # appended to the user name. # # If you're not running that NAS, you don't need # this hack. with_specialix_jetstream_hack = no # Cisco (and Quintum in Cisco mode) sends it's VSA attributes # with the attribute name *again* in the string, like: # # H323-Attribute = "h323-attribute=value". # # If this configuration item is set to 'yes', then # the redundant data in the the attribute text is stripped # out. The result is: # # H323-Attribute = "value" # # If you're not running a Cisco or Quintum NAS, you don't # need this hack. with_cisco_vsa_hack = no } # Livingston-style 'users' file # files { usersfile = ${confdir}/users acctusersfile = ${confdir}/acct_users # If you want to use the old Cistron 'users' file # with FreeRADIUS, you should change the next line # to 'compat = cistron'. You can the copy your 'users' # file from Cistron. compat = no } # Write a detailed log of all accounting records received. # detail { # Note that we do NOT use NAS-IP-Address here, as # that attribute MAY BE from the originating NAS, and # NOT from the proxy which actually sent us the # request. The Client-IP-Address attribute is ALWAYS # the address of the client which sent us the # request. # # The following line creates a new detail file for # every radius client (by IP address or hostname). # In addition, a new detail file is created every # day, so that the detail file doesn't have to go # through a 'log rotation' # # If your detail files are large, you may also want # to add a ':%H' (see doc/variables.txt) to the end # of it, to create a new detail file every hour, e.g.: # # ..../detail-%Y%m%d:%H # # This will create a new detail file for every hour. # detailfile = ${radacctdir}/%{Client-IP-Address}/detail-%Y%m%d # # The Unix-style permissions on the 'detail' file. # # The detail file often contains secret or private # information about users. So by keeping the file # permissions restrictive, we can prevent unwanted # people from seeing that information. detailperm = 0600 } # Commented in orig. file HS # # Many people want to log authentication requests. # Rather than modifying the server core to print out more # messages, we can use a different instance of the 'detail' # module, to log the authentication requests to a file. # # You will also need to un-comment the 'auth_log' line # in the 'authorize' section, below. # detail auth_log { detailfile = ${radacctdir}/%{Client-IP-Address}/auth-detail-%Y%m%d # # This MUST be 0600, otherwise anyone can read # the users passwords! # detailperm = 0600 } # # This module logs authentication reply packets sent # to a NAS. Both Access-Accept and Access-Reject packets # are logged. # # You will also need to un-comment the 'reply_log' line # in the 'post-auth' section, below. # # detail reply_log { # detailfile = ${radacctdir}/%{Client-IP-Address}/reply-detail-%Y%m%d # # This MUST be 0600, otherwise anyone can read # the users passwords! # detailperm = 0600 # } # # This module logs packets proxied to a home server. # # You will also need to un-comment the 'pre_proxy_log' line # in the 'pre-proxy' section, below. # # detail pre_proxy_log { # detailfile = ${radacctdir}/%{Client-IP-Address}/pre-proxy-detail-%Y%m%d # # This MUST be 0600, otherwise anyone can read # the users passwords! # detailperm = 0600 # } # # This module logs response packets from a home server. # # You will also need to un-comment the 'post_proxy_log' line # in the 'post-proxy' section, below. # # detail post_proxy_log { # detailfile = ${radacctdir}/%{Client-IP-Address}/post-proxy-detail-%Y%m%d # # This MUST be 0600, otherwise anyone can read # the users passwords! # detailperm = 0600 # } # Uncommented in orig. file - HS # Create a unique accounting session Id. Many NASes re-use or # repeat values for Acct-Session-Id, causing no end of # confusion. # # This module will add a (probably) unique session id # to an accounting packet based on the attributes listed # below found in the packet. See doc/rlm_acct_unique for # more information. # #acct_unique { # key = "User-Name, Acct-Session-Id, NAS-IP-Address, Client-IP-Address, NAS-Port" #} # Uncommented in orig. file HS # Include another file that has the SQL-related configuration. # This is another file only because it tends to be big. # # The following configuration file is for use with MySQL. # # For Postgresql, use: ${confdir}/postgresql.conf # For MS-SQL, use: ${confdir}/mssql.conf # For Oracle, use: ${confdir}/oraclesql.conf # #$INCLUDE ${confdir}/sql.conf # For Cisco VoIP specific accounting with Postgresql, # use: ${confdir}/pgsql-voip.conf # # You will also need the sql schema from: # src/billing/cisco_h323_db_schema-postgres.sql # Note: This config can be use AS WELL AS the standard sql # config if you need SQL based Auth # Write a 'utmp' style file, of which users are currently # logged in, and where they've logged in from. # # This file is used mainly for Simultaneous-Use checking, # and also 'radwho', to see who's currently logged in. # radutmp { # Where the file is stored. It's not a log file, # so it doesn't need rotating. # filename = ${logdir}/radutmp # The field in the packet to key on for the # 'user' name, If you have other fields which you want # to use to key on to control Simultaneous-Use, # then you can use them here. # # Note, however, that the size of the field in the # 'utmp' data structure is small, around 32 # characters, so that will limit the possible choices # of keys. # # You may want instead: %{Stripped-User-Name:-%{User-Name}} username = %{User-Name} # Whether or not we want to treat "user" the same # as "USER", or "User". Some systems have problems # with case sensitivity, so this should be set to # 'no' to enable the comparisons of the key attribute # to be case insensitive. # case_sensitive = yes # Accounting information may be lost, so the user MAY # have logged off of the NAS, but we haven't noticed. # If so, we can verify this information with the NAS, # # If we want to believe the 'utmp' file, then this # configuration entry can be set to 'no'. # # yes in orig. file HS check_with_nas = no # Set the file permissions, as the contents of this file # are usually private. perm = 0600 callerid = "yes" } # "Safe" radutmp - does not contain caller ID, so it can be # world-readable, and radwho can work for normal users, without # exposing any information that isn't already exposed by who(1). # # This is another 'instance' of the radutmp module, but it is given # then name "sradutmp" to identify it later in the "accounting" # section. radutmp sradutmp { filename = ${logdir}/sradutmp perm = 0644 callerid = "no" } # attr_filter - filters the attributes received in replies from # proxied servers, to make sure we send back to our RADIUS client # only allowed attributes. attr_filter { attrsfile = ${confdir}/attrs } # counter module: # This module takes an attribute (count-attribute). # It also takes a key, and creates a counter for each unique # key. The count is incremented when accounting packets are # received by the server. The value of the increment depends # on the attribute type. # If the attribute is Acct-Session-Time or of an integer type we add the # value of the attribute. If it is anything else we increase the # counter by one. # # The 'reset' parameter defines when the counters are all reset to # zero. It can be hourly, daily, weekly, monthly or never. # # hourly: Reset on 00:00 of every hour # daily: Reset on 00:00:00 every day # weekly: Reset on 00:00:00 on sunday # monthly: Reset on 00:00:00 of the first day of each month # # It can also be user defined. It should be of the form: # num[hdwm] where: # h: hours, d: days, w: weeks, m: months # If the letter is ommited days will be assumed. In example: # reset = 10h (reset every 10 hours) # reset = 12 (reset every 12 days) # # # The check-name attribute defines an attribute which will be # registered by the counter module and can be used to set the # maximum allowed value for the counter after which the user # is rejected. # Something like: # # DEFAULT Max-Daily-Session := 36000 # Fall-Through = 1 # # You should add the counter module in the instantiate # section so that it registers check-name before the files # module reads the users file. # # If check-name is set and the user is to be rejected then we # send back a Reply-Message and we log a Failure-Message in # the radius.log # If the count attribute is Acct-Session-Time then on each login # we send back the remaining online time as a Session-Timeout attribute # # The counter-name can also be used instead of using the check-name # like below: # # DEFAULT Daily-Session-Time > 3600, Auth-Type = Reject # Reply-Message = "You've used up more than one hour today" # # The allowed-servicetype attribute can be used to only take # into account specific sessions. For example if a user first # logs in through a login menu and then selects ppp there will # be two sessions. One for Login-User and one for Framed-User # service type. We only need to take into account the second one. # # The module should be added in the instantiate, authorize and # accounting sections. Make sure that in the authorize # section it comes after any module which sets the # 'check-name' attribute. # counter daily { filename = ${raddbdir}/db.daily key = User-Name count-attribute = Acct-Session-Time reset = daily counter-name = Daily-Session-Time check-name = Max-Daily-Session allowed-servicetype = Framed-User cache-size = 5000 } # The "always" module is here for debugging purposes. Each # instance simply returns the same result, always, without # doing anything. always fail { rcode = fail } always reject { rcode = reject } always ok { rcode = ok simulcount = 0 mpp = no } # # The 'expression' module currently has no configuration. # # This module is useful only for 'xlat'. To use it, # put 'exec' into the 'instantiate' section. You can then # do dynamic translation of attributes like: # # Attribute-Name = `%{expr:2 + 3 + %{exec: uid -u}}` # # The value of the attribute will be replaced with the output # of the program which is executed. Due to RADIUS protocol # limitations, any output over 253 bytes will be ignored. expr { } # # The 'digest' module currently has no configuration. # # "Digest" authentication against a Cisco SIP server. # See 'doc/rfc/draft-sterman-aaa-sip-00.txt' for details # on performing digest authentication for Cisco SIP servers. # digest { } # # Execute external programs # # This module is useful only for 'xlat'. To use it, # put 'exec' into the 'instantiate' section. You can then # do dynamic translation of attributes like: # # Attribute-Name = `%{exec:/path/to/program args}` # # The value of the attribute will be replaced with the output # of the program which is executed. Due to RADIUS protocol # limitations, any output over 253 bytes will be ignored. # # The RADIUS attributes from the user request will be placed # into environment variables of the executed program, as # described in 'doc/variables.txt' # exec { wait = yes input_pairs = request } # # This is a more general example of the execute module. # # This one is called "echo". # # Attribute-Name = `%{echo:/path/to/program args}` # # If you wish to execute an external program in more than # one section (e.g. 'authorize', 'pre_proxy', etc), then it # is probably best to define a different instance of the # 'exec' module for every section. # exec echo { # # Wait for the program to finish. # # If we do NOT wait, then the program is "fire and # forget", and any output attributes from it are ignored. # # If we are looking for the program to output # attributes, and want to add those attributes to the # request, then we MUST wait for the program to # finish, and therefore set 'wait=yes' # # allowed values: {no, yes} wait = yes # # The name of the program to execute, and it's # arguments. Dynamic translation is done on this # field, so things like the following example will # work. # program = "/bin/echo %{User-Name}" # # The attributes which are placed into the # environment variables for the program. # # Allowed values are: # # request attributes from the request # config attributes from the configuration items list # reply attributes from the reply # proxy-request attributes from the proxy request # proxy-reply attributes from the proxy reply # # Note that some attributes may not exist at some # stages. e.g. There may be no proxy-reply # attributes if this module is used in the # 'authorize' section. # input_pairs = request # # Where to place the output attributes (if any) from # the executed program. The values allowed, and the # restrictions as to availability, are the same as # for the input_pairs. # output_pairs = reply # # When to execute the program. If the packet # type does NOT match what's listed here, then # the module does NOT execute the program. # # For a list of allowed packet types, see # the 'dictionary' file, and look for VALUEs # of the Packet-Type attribute. # # By default, the module executes on ANY packet. # Un-comment out the following line to tell the # module to execute only if an Access-Accept is # being sent to the NAS. # packet_type = Access-Accept } #Uncommented in orig. file HS # Do server side ip pool management. Should be added in post-auth and # accounting sections. # # The module also requires the existance of the Pool-Name # attribute. That way the administrator can add the Pool-Name # attribute in the user profiles and use different pools # for different users. The Pool-Name attribute is a *check* item not # a reply item. # # Example: # radiusd.conf: ippool students { [...] } # users file : DEFAULT Group == students, Pool-Name := "students" # # ********* IF YOU CHANGE THE RANGE PARAMETERS YOU MUST ********* # ********* THEN ERASE THE DB FILES ********* # #ippool main_pool { # range-start,range-stop: The start and end ip # addresses for the ip pool # range-start = 192.168.1.1 # range-stop = 192.168.3.254 # netmask: The network mask used for the ip's # netmask = 255.255.255.0 # cache-size: The gdbm cache size for the db # files. Should be equal to the number of ip's # available in the ip pool # cache-size = 800 # session-db: The main db file used to allocate ip's to clients # session-db = ${raddbdir}/db.ippool # ip-index: Helper db index file used in multilink # ip-index = ${raddbdir}/db.ipindex # override: Will this ippool override a Framed-IP-Address already set # override = no # maximum-timeout: If not zero specifies the maximum time in seconds an # entry may be active. Default: 0 # maximum-timeout = 0 #} # ANSI X9.9 token support. Not included by default. # $INCLUDE ${confdir}/x99.conf } # Instantiation # # This section orders the loading of the modules. Modules # listed here will get loaded BEFORE the later sections like # authorize, authenticate, etc. get examined. # # This section is not strictly needed. When a section like # authorize refers to a module, it's automatically loaded and # initialized. However, some modules may not be listed in any # of the following sections, so they can be listed here. # # Also, listing modules here ensures that you have control over # the order in which they are initalized. If one module needs # something defined by another module, you can list them in order # here, and ensure that the configuration will be OK. # instantiate { # # Allows the execution of external scripts. # The entire command line (and output) must fit into 253 bytes. # # e.g. Framed-Pool = `%{exec:/bin/echo foo}` exec # # The expression module doesn't do authorization, # authentication, or accounting. It only does dynamic # translation, of the form: # # Session-Timeout = `%{expr:2 + 3}` # # So the module needs to be instantiated, but CANNOT be # listed in any other section. See 'doc/rlm_expr' for # more information. # expr # # We add the counter module here so that it registers # the check-name attribute before any module which sets # it # daily } # Authorization. First preprocess (hints and huntgroups files), # then realms, and finally look in the "users" file. # # The order of the realm modules will determine the order that # we try to find a matching realm. # # Make *sure* that 'preprocess' comes before any realm if you # need to setup hints for the remote radius server authorize { # # The preprocess module takes care of sanitizing some bizarre # attributes in the request, and turning them into attributes # which are more standard. # # It takes care of processing the 'raddb/hints' and the # 'raddb/huntgroups' files. # # It also adds the %{Client-IP-Address} attribute to the request. preprocess # # If you want to have a log of authentication requests, # un-comment the following line, and the 'detail auth_log' # section, above. auth_log # attr_filter # # The chap module will set 'Auth-Type := CHAP' if we are # handling a CHAP request and Auth-Type has not already been set # chap # # If the users are logging in with an MS-CHAP-Challenge # attribute for authentication, the mschap module will find # the MS-CHAP-Challenge attribute, and add 'Auth-Type := MS-CHAP' # to the request, which will cause the server to then use # the mschap module for authentication. # mschap # # If you have a Cisco SIP server authenticating against # FreeRADIUS, uncomment the following line, and the 'digest' # line in the 'authenticate' section. # digest # # Look for IPASS style 'realm/', and if not found, look for # '@realm', and decide whether or not to proxy, based on # that. # IPASS # # If you are using multiple kinds of realms, you probably # want to set "ignore_null = yes" for all of them. # Otherwise, when the first style of realm doesn't match, # the other styles won't be checked. # suffix # ntdomain # # This module takes care of EAP-MD5, EAP-TLS, and EAP-LEAP # authentication. # # It also sets the EAP-Type attribute in the request # attribute list to the EAP type from the packet. eap # # Read the 'users' file files # # Look in an SQL database. The schema of the database # is meant to mirror the "users" file. # # See "Authorization Queries" in sql.conf # sql # # If you are using /etc/smbpasswd, and are also doing # mschap authentication, the un-comment this line, and # configure the 'etc_smbpasswd' module, above. # etc_smbpasswd # # The ldap module will set Auth-Type to LDAP if it has not # already been set # ldap # # Enforce daily limits on time spent logged in. # daily # # Use the checkval module # checkval } # Authentication. # # # This section lists which modules are available for authentication. # Note that it does NOT mean 'try each module in order'. It means # that a module from the 'authorize' section adds a configuration # attribute 'Auth-Type := FOO'. That authentication type is then # used to pick the apropriate module from the list below. # # In general, you SHOULD NOT set the Auth-Type attribute. The server # will figure it out on its own, and will do the right thing. The # most common side effect of erroneously setting the Auth-Type # attribute is that one authentication method will work, but the # others will not. # # The common reasons to set the Auth-Type attribute by hand # is to either forcibly reject the user, or forcibly accept him. # authenticate { # # PAP authentication, when a back-end database listed # in the 'authorize' section supplies a password. The # password can be clear-text, or encrypted. #Auth-Type PAP { # pap #} # # Most people want CHAP authentication # A back-end database listed in the 'authorize' section # MUST supply a CLEAR TEXT password. Encrypted passwords # won't work. #Auth-Type CHAP { # chap #} # # MSCHAP authentication. #Auth-Type MS-CHAP { # mschap #} # # If you have a Cisco SIP server authenticating against # FreeRADIUS, uncomment the following line, and the 'digest' # line in the 'authorize' section. # digest # # Pluggable Authentication Modules. # pam # # See 'man getpwent' for information on how the 'unix' # module checks the users password. Note that packets # containing CHAP-Password attributes CANNOT be authenticated # against /etc/passwd! See the FAQ for details. # # unix # Uncomment it if you want to use ldap for authentication # # Note that this means "check plain-text password against # the ldap database", which means that EAP won't work, # as it does not supply a plain-text password. # Auth-Type LDAP { # ldap # } # # Allow EAP authentication. eap } # # Pre-accounting. Decide which accounting type to use. # #preacct { # preprocess # # Ensure that we have a semi-unique identifier for every # request, and many NAS boxes are broken. # acct_unique # # Look for IPASS-style 'realm/', and if not found, look for # '@realm', and decide whether or not to proxy, based on # that. # # Accounting requests are generally proxied to the same # home server as authentication requests. # IPASS # suffix # ntdomain # # Read the 'acct_users' file # files #} # # Accounting. Log the accounting data. # accounting { # # Create a 'detail'ed log of the packets. # Note that accounting requests which are proxied # are also logged in the detail file. detail # daily # Update the wtmp file # # If you don't use "radlast", you can delete this line. unix # # For Simultaneous-Use tracking. # # Due to packet losses in the network, the data here # may be incorrect. There is little we can do about it. radutmp # sradutmp # Return an address to the IP Pool when we see a stop record. # main_pool # # Log traffic to an SQL database. # # See "Accounting queries" in sql.conf # sql # Cisco VoIP specific bulk accounting # pgsql-voip } # Session database, used for checking Simultaneous-Use. Either the radutmp # or rlm_sql module can handle this. # The rlm_sql module is *much* faster session { radutmp # # See "Simultaneous Use Checking Querie" in sql.conf # sql } # Post-Authentication # Once we KNOW that the user has been authenticated, there are # additional steps we can take. post-auth { # Get an address from the IP Pool. # main_pool # # If you want to have a log of authentication replies, # un-comment the following line, and the 'detail reply_log' # section, above. # reply_log # # After authenticating the user, do another SQL qeury. # # See "Authentication Logging Queries" in sql.conf # sql # # Un-comment the following if you have set # 'edir_account_policy_check = yes' in the ldap module sub-section of # the 'modules' section. # # ldap # # Access-Reject packets are sent through the REJECT sub-section of the # post-auth section. # Uncomment the following and set the module name to the ldap instance # name if you have set 'edir_account_policy_check = yes' in the ldap # module sub-section of the 'modules' section. # # Post-Auth-Type REJECT { # insert-module-name-here # } } # # When the server decides to proxy a request to a home server, # the proxied request is first passed through the pre-proxy # stage. This stage can re-write the request, or decide to # cancel the proxy. # # Only a few modules currently have this method. # pre-proxy { # attr_rewrite # Uncomment the following line if you want to change attributes # as defined in the preproxy_users file. # files # If you want to have a log of packets proxied to a home # server, un-comment the following line, and the # 'detail pre_proxy_log' section, above. # pre_proxy_log } # # When the server receives a reply to a request it proxied # to a home server, the request may be massaged here, in the # post-proxy stage. # post-proxy { # # If you want to have a log of replies from a home server, # un-comment the following line, and the 'detail post_proxy_log' # section, above. # post_proxy_log # attr_rewrite # Uncomment the following line if you want to filter replies from # remote proxies based on the rules defined in the 'attrs' file. # attr_filter # # If you are proxying LEAP, you MUST configure the EAP # module, and you MUST list it here, in the post-proxy # stage. # # You MUST also use the 'nostrip' option in the 'realm' # configuration. Otherwise, the User-Name attribute # in the proxied request will not match the user name # hidden inside of the EAP packet, and the end server will # reject the EAP request. # eap } eap.conf: # # Whatever you do, do NOT set 'Auth-Type := EAP'. The server # is smart enough to figure this out on its own. The most # common side effect of setting 'Auth-Type := EAP' is that the # users then cannot use ANY other authentication method. # # $Id: eap.conf,v 1.4 2004/04/15 18:34:41 aland Exp $ # eap { # Invoke the default supported EAP type when # EAP-Identity response is received. # # The incoming EAP messages DO NOT specify which EAP # type they will be using, so it MUST be set here. # # For now, only one default EAP type may be used at a time. # # If the EAP-Type attribute is set by another module, # then that EAP type takes precedence over the # default type configured here. # default_eap_type = md5 # A list is maintained to correlate EAP-Response # packets with EAP-Request packets. After a # configurable length of time, entries in the list # expire, and are deleted. # timer_expire = 60 # There are many EAP types, but the server has support # for only a limited subset. If the server receives # a request for an EAP type it does not support, then # it normally rejects the request. By setting this # configuration to "yes", you can tell the server to # instead keep processing the request. Another module # MUST then be configured to proxy the request to # another RADIUS server which supports that EAP type. # # If another module is NOT configured to handle the # request, then the request will still end up being # rejected. ignore_unknown_eap_types = no # Cisco AP1230B firmware 12.2(13)JA1 has a bug. When given # a User-Name attribute in an Access-Accept, it copies one # more byte than it should. # # We can work around it by configurably adding an extra # zero byte. cisco_accounting_username_bug = no # Supported EAP-types # # We do NOT recommend using EAP-MD5 authentication # for wireless connections. It is insecure, and does # not provide for dynamic WEP keys. # md5 { } # Cisco LEAP # # We do not recommend using LEAP in new deployments. See: # http://www.securiteam.com/tools/5TP012ACKE.html # # Cisco LEAP uses the MS-CHAP algorithm (but not # the MS-CHAP attributes) to perform it's authentication. # # As a result, LEAP *requires* access to the plain-text # User-Password, or the NT-Password attributes. # 'System' authentication is impossible with LEAP. # leap { } # Generic Token Card. # # Currently, this is only permitted inside of EAP-TTLS, # or EAP-PEAP. The module "challenges" the user with # text, and the response from the user is taken to be # the User-Password. # # Proxying the tunneled EAP-GTC session is a bad idea, # the users password will go over the wire in plain-text, # for anyone to see. # gtc { # The default challenge, which many clients # ignore.. #challenge = "Password: " # The plain-text response which comes back # is put into a User-Password attribute, # and passed to another module for # authentication. This allows the EAP-GTC # response to be checked against plain-text, # or crypt'd passwords. # # If you say "Local" instead of "PAP", then # the module will look for a User-Password # configured for the request, and do the # authentication itself. # auth_type = PAP } ## EAP-TLS # # To generate ctest certificates, run the script # # ../scripts/certs.sh # # The documents on http://www.freeradius.org/doc # are old, but may be helpful. # # See also: # # http://www.dslreports.com/forum/remark,9286052~mode=flat # #tls { # private_key_password = whatever # private_key_file = ${raddbdir}/certs/cert-srv.pem # If Private key & Certificate are located in # the same file, then private_key_file & # certificate_file must contain the same file # name. # certificate_file = ${raddbdir}/certs/cert-srv.pem # Trusted Root CA list # CA_file = ${raddbdir}/certs/demoCA/cacert.pem # dh_file = ${raddbdir}/certs/dh # random_file = ${raddbdir}/certs/random # # This can never exceed the size of a RADIUS # packet (4096 bytes), and is preferably half # that, to accomodate other attributes in # RADIUS packet. On most APs the MAX packet # length is configured between 1500 - 1600 # In these cases, fragment size should be # 1024 or less. # # fragment_size = 1024 # include_length is a flag which is # by default set to yes If set to # yes, Total Length of the message is # included in EVERY packet we send. # If set to no, Total Length of the # message is included ONLY in the # First packet of a fragment series. # # include_length = yes # Check the Certificate Revocation List # # 1) Copy CA certificates and CRLs to same directory. # 2) Execute 'c_rehash <CA certs&CRLs Directory>'. # 'c_rehash' is OpenSSL's command. # 3) Add 'CA_path=<CA certs&CRLs directory>' # to radiusd.conf's tls section. # 4) uncomment the line below. # 5) Restart radiusd # check_crl = yes # # If check_cert_cn is set, the value will # be xlat'ed and checked against the CN # in the client certificate. If the values # do not match, the certificate verification # will fail rejecting the user. # # check_cert_cn = %{User-Name} #} # The TTLS module implements the EAP-TTLS protocol, # which can be described as EAP inside of Diameter, # inside of TLS, inside of EAP, inside of RADIUS... # # Surprisingly, it works quite well. # # The TTLS module needs the TLS module to be installed # and configured, in order to use the TLS tunnel # inside of the EAP packet. You will still need to # configure the TLS module, even if you do not want # to deploy EAP-TLS in your network. Users will not # be able to request EAP-TLS, as it requires them to # have a client certificate. EAP-TTLS does not # require a client certificate. # #ttls { # The tunneled EAP session needs a default # EAP type which is separate from the one for # the non-tunneled EAP module. Inside of the # TTLS tunnel, we recommend using EAP-MD5. # If the request does not contain an EAP # conversation, then this configuration entry # is ignored. # default_eap_type = md5 # The tunneled authentication request does # not usually contain useful attributes # like 'Calling-Station-Id', etc. These # attributes are outside of the tunnel, # and normally unavailable to the tunneled # authentication request. # # By setting this configuration entry to # 'yes', any attribute which NOT in the # tunneled authentication request, but # which IS available outside of the tunnel, # is copied to the tunneled request. # # allowed values: {no, yes} # copy_request_to_tunnel = no # The reply attributes sent to the NAS are # usually based on the name of the user # 'outside' of the tunnel (usually # 'anonymous'). If you want to send the # reply attributes based on the user name # inside of the tunnel, then set this # configuration entry to 'yes', and the reply # to the NAS will be taken from the reply to # the tunneled request. # # allowed values: {no, yes} # use_tunneled_reply = no #} # # The tunneled EAP session needs a default EAP type # which is separate from the one for the non-tunneled # EAP module. Inside of the TLS/PEAP tunnel, we # recommend using EAP-MS-CHAPv2. # # The PEAP module needs the TLS module to be installed # and configured, in order to use the TLS tunnel # inside of the EAP packet. You will still need to # configure the TLS module, even if you do not want # to deploy EAP-TLS in your network. Users will not # be able to request EAP-TLS, as it requires them to # have a client certificate. EAP-PEAP does not # require a client certificate. # # peap { # The tunneled EAP session needs a default # EAP type which is separate from the one for # the non-tunneled EAP module. Inside of the # PEAP tunnel, we recommend using MS-CHAPv2, # as that is the default type supported by # Windows clients. # default_eap_type = mschapv2 #} # # This takes no configuration. # # Note that it is the EAP MS-CHAPv2 sub-module, not # the main 'mschap' module. # # Note also that in order for this sub-module to work, # the main 'mschap' module MUST ALSO be configured. # # This module is the *Microsoft* implementation of MS-CHAPv2 # in EAP. There is another (incompatible) implementation # of MS-CHAPv2 in EAP by Cisco, which FreeRADIUS does not # currently support. # mschapv2 { } } FreeRadius output: [root@radiusd raddb]# /opt/radiusd/sbin/runradiusd -X + LD_LIBRARY_PATH=/opt/openssl/lib + LD_PRELOAD=/opt/openssl/lib/libcrypto.so + export LD_LIBRARY_PATH + export LD_PRELOAD + /opt/radiusd/sbin/radiusd -X Starting - reading configuration files ... reread_config: reading radiusd.conf Config: including file: /opt/radiusd/etc/raddb/clients.conf Config: including file: /opt/radiusd/etc/raddb/snmp.conf Config: including file: /opt/radiusd/etc/raddb/eap.conf main: prefix = "/opt/radiusd" main: localstatedir = "/opt/radiusd/var" main: logdir = "/opt/radiusd/var/log/radius" main: libdir = "/opt/radiusd/lib" main: radacctdir = "/opt/radiusd/var/log/radius/radacct" main: hostname_lookups = no main: max_request_time = 30 main: cleanup_delay = 5 main: max_requests = 1024 main: delete_blocked_requests = 0 main: port = 0 main: allow_core_dumps = no main: log_stripped_names = no main: log_file = "/opt/radiusd/var/log/radius/radius.log" main: log_auth = yes main: log_auth_badpass = yes main: log_auth_goodpass = yes main: pidfile = "/opt/radiusd/var/run/radiusd/radiusd.pid" main: bind_address = radiusd.ece.neu.edu IP address [127.0.0.1] main: user = "(null)" main: group = "(null)" main: usercollide = no main: lower_user = "no" main: lower_pass = "no" main: nospace_user = "no" main: nospace_pass = "no" main: checkrad = "/opt/radiusd/sbin/checkrad" main: proxy_requests = no security: max_attributes = 200 security: reject_delay = 1 security: status_server = no main: debug_level = 0 read_config_files: reading dictionary read_config_files: reading naslist Using deprecated naslist file. Support for this will go away soon. read_config_files: reading clients read_config_files: reading realms radiusd: entering modules setup Module: Library search path is /opt/radiusd/lib Module: Loaded exec exec: wait = yes exec: program = "(null)" exec: input_pairs = "request" exec: output_pairs = "(null)" exec: packet_type = "(null)" rlm_exec: Wait=yes but no output defined. Did you mean output=none? Module: Instantiated exec (exec) Module: Loaded expr Module: Instantiated expr (expr) Module: Loaded eap eap: default_eap_type = "tls" eap: timer_expire = 60 eap: ignore_unknown_eap_types = no eap: cisco_accounting_username_bug = no tls: rsa_key_exchange = no tls: dh_key_exchange = yes tls: rsa_key_length = 512 tls: dh_key_length = 512 tls: verify_depth = 0 tls: CA_path = "(null)" tls: pem_file_type = yes tls: private_key_file = "/opt/radiusd/etc/1x/radiusd.ece.neu.edu.pem" tls: certificate_file = "/opt/radiusd/etc/1x/radiusd.ece.neu.edu.pem" tls: CA_file = "/opt/radiusd/etc/1x/root.pem" tls: private_key_password = "serverpwd" tls: dh_file = "/opt/radiusd/etc/1x/dh" tls: random_file = "/opt/radiusd/etc/1x/random" tls: fragment_size = 1024 tls: include_length = yes tls: check_crl = no tls: check_cert_cn = "(null)" rlm_eap: Loaded and initialized type tls Module: Instantiated eap (eap) Module: Loaded preprocess preprocess: huntgroups = "/opt/radiusd/etc/raddb/huntgroups" preprocess: hints = "/opt/radiusd/etc/raddb/hints" preprocess: with_ascend_hack = no preprocess: ascend_channels_per_line = 23 preprocess: with_ntdomain_hack = no preprocess: with_specialix_jetstream_hack = no preprocess: with_cisco_vsa_hack = no Module: Instantiated preprocess (preprocess) Module: Loaded detail detail: detailfile = "/opt/radiusd/var/log/radius/radacct/%{Client-IP-Address}/auth-detail-%Y %m%d" detail: detailperm = 384 detail: dirperm = 493 detail: locking = no Module: Instantiated detail (auth_log) Module: Loaded realm realm: format = "suffix" realm: delimiter = "@" realm: ignore_default = no realm: ignore_null = no Module: Instantiated realm (suffix) Module: Loaded files files: usersfile = "/opt/radiusd/etc/raddb/users" files: acctusersfile = "/opt/radiusd/etc/raddb/acct_users" files: preproxy_usersfile = "/opt/radiusd/etc/raddb/preproxy_users" files: compat = "no" Module: Instantiated files (files) detail: detailfile = "/opt/radiusd/var/log/radius/radacct/%{Client-IP-Address}/detail-%Y%m%d" detail: detailperm = 384 detail: dirperm = 493 detail: locking = no Module: Instantiated detail (detail) Module: Loaded System unix: cache = no unix: passwd = "(null)" unix: shadow = "(null)" unix: group = "(null)" unix: radwtmp = "/opt/radiusd/var/log/radius/radwtmp" unix: usegroup = no unix: cache_reload = 600 Module: Instantiated unix (unix) Module: Loaded radutmp radutmp: filename = "/opt/radiusd/var/log/radius/radutmp" radutmp: username = "%{User-Name}" radutmp: case_sensitive = yes radutmp: check_with_nas = no radutmp: perm = 384 radutmp: callerid = yes Module: Instantiated radutmp (radutmp) Listening on authentication 127.0.0.1:1812 Listening on accounting 127.0.0.1:1813 Ready to process requests.