alvarion not receiving Filter-Id parameters

6 Jan 2012

      I am trying to get freeradius to authorize the services on an Alvarion

BreezeMax 5000 system ver 1.7.
I have gotten the cpe authenticated but services are not assigned.

I have downloaded on 1/5/2012 the Master from git.
I modified the dictionary file such that
$INCLUDE dictionary.alvarion.wimax.v2_2 replaced $INCLUDE
dictionary.alvarion
$INCLUDE dictionary.wimax.alvarion replaced $INCLUDE dictionary.wimax
I ran configure  using ./configure --with-experimental-modules
I ran make and make install (it compiled, installed and ran)
wimax was uncommented in 2 places in default file
     one in the authorize section and one in the post-auth section
     (the wimax module indicates there should also be one in the
"preacct" section but I do not find that one nor can I figure where it
should be)
and the following were uncommented in default file
         update request {
                WiMAX-MN-NAI = "%{User-Name}"
         }
          update reply {
             WiMAX-FA-RK-Key = 0x00
             WiMAX-MSK = "%{EAP-MSK}"
         }
the following users were defined with these replies in the user file
"wimax1@WIMAX.COM" Cleartext-Password := "wimax"
         Filter-Id = "SP=sp1:MSF=msf1;SP=sp_data_eth:MSF=msf_data_eth;",
Session-Timeout = 1200, Termination-Action = RADIUS-Request
"KeepAliveUserNameAndPassword" Cleartext-Password :=
"KeepAliveUserNameAndPassword"
         Filter-Id = "SP=sp1:MSF=msf1;SP=sp_data_eth:MSF=msf_data_eth;",
Session-Timeout = 1200, Termination-Action = RADIUS-Request

(I don't think I needed the keepalive one but I put it there anyways.)
in the above filters I have tried both with and without a trailing ;
after msf_data_eth and before the " mark
no changes were made in the inner-tunnel file
delete_mppe_keys = yes  in the wimax module (I've tried with both yes
and no)

fr seems to work. I see that the Filter-Id is indicated for the reply
(see below).
The Alvarion CPE does get authenticated according to the CPE but there
are no services defined for the CPE

sp1, msf1, sp_data_eth, and msf_data_eth are all defined in the BTS.
What is it that I am missing in configuration of the FreeRadius?

below is a radiusd -X run

FreeRADIUS Version 3.0.0, for host x86_64-unknown-linux-gnu, built on
Jan  6 2012 at 15:07:59
Copyright (C) 1999-2009 The FreeRADIUS server project and contributors.
There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A
PARTICULAR PURPOSE.
You may redistribute copies of FreeRADIUS under the terms of the
GNU General Public License v2.

Starting - reading configuration files ...
including configuration file /usr/local/etc/raddb/radiusd.conf
including configuration file /usr/local/etc/raddb/proxy.conf
including configuration file /usr/local/etc/raddb/clients.conf
including files in directory /usr/local/etc/raddb/modules/
including configuration file /usr/local/etc/raddb/modules/pam
including configuration file /usr/local/etc/raddb/modules/wimax
including configuration file /usr/local/etc/raddb/modules/always
including configuration file /usr/local/etc/raddb/modules/attr_filter
including configuration file /usr/local/etc/raddb/modules/ntlm_auth
including configuration file /usr/local/etc/raddb/modules/attr_rewrite
including configuration file /usr/local/etc/raddb/modules/smsotp
including configuration file /usr/local/etc/raddb/modules/inner-eap
including configuration file /usr/local/etc/raddb/modules/exec
including configuration file /usr/local/etc/raddb/modules/rediswho
including configuration file /usr/local/etc/raddb/modules/counter
including configuration file /usr/local/etc/raddb/modules/detail
including configuration file /usr/local/etc/raddb/modules/pap
including configuration file /usr/local/etc/raddb/modules/mschap
including configuration file /usr/local/etc/raddb/modules/expiration
including configuration file /usr/local/etc/raddb/modules/krb5
including configuration file /usr/local/etc/raddb/modules/soh
including configuration file /usr/local/etc/raddb/modules/preprocess
including configuration file /usr/local/etc/raddb/modules/sqlippool
including configuration file /usr/local/etc/raddb/sql/postgresql/ippool.conf
including configuration file /usr/local/etc/raddb/modules/expr
including configuration file /usr/local/etc/raddb/modules/sql
including configuration file /usr/local/etc/raddb/sql/mysql/dialup.conf
including configuration file /usr/local/etc/raddb/modules/ippool
including configuration file /usr/local/etc/raddb/modules/smbpasswd
including configuration file /usr/local/etc/raddb/modules/sradutmp
including configuration file /usr/local/etc/raddb/modules/opendirectory
including configuration file /usr/local/etc/raddb/modules/ldap
including configuration file /usr/local/etc/raddb/modules/etc_group
including configuration file /usr/local/etc/raddb/modules/eap
including configuration file /usr/local/etc/raddb/modules/policy
including configuration file /usr/local/etc/raddb/modules/linelog
including configuration file /usr/local/etc/raddb/modules/radutmp
including configuration file /usr/local/etc/raddb/modules/dynamic_clients
including configuration file /usr/local/etc/raddb/modules/mac2vlan
including configuration file /usr/local/etc/raddb/modules/detail.example.com
including configuration file
/usr/local/etc/raddb/modules/sqlcounter_expire_on_login
including configuration file /usr/local/etc/raddb/modules/realm
including configuration file /usr/local/etc/raddb/modules/files
including configuration file /usr/local/etc/raddb/modules/logintime
including configuration file /usr/local/etc/raddb/modules/cui
including configuration file /usr/local/etc/raddb/modules/otp
including configuration file /usr/local/etc/raddb/modules/digest
including configuration file /usr/local/etc/raddb/modules/acct_unique
including configuration file /usr/local/etc/raddb/modules/checkval
including configuration file /usr/local/etc/raddb/modules/sql_log
including configuration file /usr/local/etc/raddb/modules/perl
including configuration file /usr/local/etc/raddb/modules/redis
including configuration file /usr/local/etc/raddb/modules/replicate
including configuration file /usr/local/etc/raddb/modules/chap
including configuration file /usr/local/etc/raddb/modules/echo
including configuration file /usr/local/etc/raddb/modules/unix
including configuration file /usr/local/etc/raddb/modules/utf8
including configuration file /usr/local/etc/raddb/modules/passwd
including configuration file /usr/local/etc/raddb/modules/detail.log
including configuration file /usr/local/etc/raddb/modules/mac2ip
including configuration file /usr/local/etc/raddb/policy.conf
including files in directory /usr/local/etc/raddb/sites-enabled/
including configuration file /usr/local/etc/raddb/sites-enabled/default
including configuration file
/usr/local/etc/raddb/sites-enabled/control-socket
including configuration file /usr/local/etc/raddb/sites-enabled/inner-tunnel
main {
  security {
     allow_core_dumps = no
  }
}
including dictionary file /usr/local/etc/raddb/dictionary
main {
     name = "radiusd"
     prefix = "/usr/local"
     localstatedir = "/usr/local/var"
     sbindir = "/usr/local/sbin"
     logdir = "/usr/local/var/log/radius"
     run_dir = "/usr/local/var/run/radiusd"
     libdir = "/usr/local/lib"
     radacctdir = "/usr/local/var/log/radius/radacct"
     hostname_lookups = no
     max_request_time = 30
     cleanup_delay = 5
     max_requests = 1024
     pidfile = "/usr/local/var/run/radiusd/radiusd.pid"
     checkrad = "/usr/local/sbin/checkrad"
     debug_level = 0
     proxy_requests = yes
  log {
     stripped_names = no
     auth = no
     auth_badpass = no
     auth_goodpass = no
  }
  security {
     max_attributes = 200
     reject_delay = 1
     status_server = yes
  }
}
radiusd: #### Loading Realms and Home Servers ####
  proxy server {
     retry_delay = 5
     retry_count = 3
     default_fallback = no
     dead_time = 120
     wake_all_if_all_dead = no
  }
  home_server localhost {
     ipaddr = 127.0.0.1
     port = 1812
     type = "auth"
     secret = "testing123"
     response_window = 20
     max_outstanding = 65536
     require_message_authenticator = yes
     zombie_period = 40
     status_check = "status-server"
     ping_interval = 30
     check_interval = 30
     num_answers_to_alive = 3
     num_pings_to_alive = 3
     revive_interval = 120
     status_check_timeout = 4
   coa {
     irt = 2
     mrt = 16
     mrc = 5
     mrd = 30
   }
   limit {
     max_connections = 16
     max_requests = 0
     lifetime = 0
     idle_timeout = 0
   }
  }
  home_server_pool my_auth_failover {
     type = fail-over
     home_server = localhost
  }
  realm example.com {
     auth_pool = my_auth_failover
  }
  realm LOCAL {
  }
radiusd: #### Loading Clients ####
  client localhost {
     ipaddr = 127.0.0.1
     require_message_authenticator = no
     secret = "testing123"
     nastype = "other"
     proto = "*"
     max_connections = 16
  }
  client 10.97.0.0/24 {
     require_message_authenticator = no
     secret = "testing123"
     shortname = "private-network-1"
     max_connections = 16
  }
radiusd: #### Instantiating modules ####
  instantiate {
  Module: Linked to module rlm_exec
  Module: Instantiating module "exec" from file
/usr/local/etc/raddb/modules/exec
   exec {
     wait = no
     input_pairs = "request"
     shell_escape = yes
   }
  Module: Linked to module rlm_expr
  Module: Instantiating module "expr" from file
/usr/local/etc/raddb/modules/expr
  Module: Linked to module rlm_expiration
  Module: Instantiating module "expiration" from file
/usr/local/etc/raddb/modules/expiration
   expiration {
     reply-message = "Password Has Expired  "
   }
  Module: Linked to module rlm_logintime
  Module: Instantiating module "logintime" from file
/usr/local/etc/raddb/modules/logintime
   logintime {
     reply-message = "You are calling outside your allowed timespan  "
     minimum-timeout = 60
   }
  }
radiusd: #### Loading Virtual Servers ####
server { # from file /usr/local/etc/raddb/radiusd.conf
  modules {
   Module: Creating Auth-Type = digest
  Module: Checking authenticate {...} for more modules to load
  Module: Linked to module rlm_pap
  Module: Instantiating module "pap" from file
/usr/local/etc/raddb/modules/pap
   pap {
     encryption_scheme = "auto"
     auto_header = no
   }
  Module: Linked to module rlm_chap
  Module: Instantiating module "chap" from file
/usr/local/etc/raddb/modules/chap
  Module: Linked to module rlm_mschap
  Module: Instantiating module "mschap" from file
/usr/local/etc/raddb/modules/mschap
   mschap {
     use_mppe = yes
     require_encryption = no
     require_strong = no
     with_ntdomain_hack = no
    passchange {
    }
     allow_retry = yes
   }
  Module: Linked to module rlm_digest
  Module: Instantiating module "digest" from file
/usr/local/etc/raddb/modules/digest
  Module: Linked to module rlm_unix
  Module: Instantiating module "unix" from file
/usr/local/etc/raddb/modules/unix
   unix {
     radwtmp = "/usr/local/var/log/radius/radwtmp"
   }
  Module: Linked to module rlm_eap
  Module: Instantiating module "eap" from file
/usr/local/etc/raddb/modules/eap
   eap {
     default_eap_type = "md5"
     timer_expire = 60
     ignore_unknown_eap_types = no
     cisco_accounting_username_bug = no
     max_sessions = 4096
   }
  Module: Linked to sub-module rlm_eap_md5
  Module: Instantiating eap-md5
  Module: Linked to sub-module rlm_eap_leap
  Module: Instantiating eap-leap
  Module: Linked to sub-module rlm_eap_gtc
  Module: Instantiating eap-gtc
    gtc {
     challenge = "Password: "
     auth_type = "PAP"
    }
  Module: Linked to sub-module rlm_eap_tls
  Module: Instantiating eap-tls
    tls {
     rsa_key_exchange = no
     dh_key_exchange = yes
     rsa_key_length = 512
     dh_key_length = 512
     verify_depth = 0
     CA_path = "/usr/local/etc/raddb/certs"
     pem_file_type = yes
     private_key_file = "/usr/local/etc/raddb/certs/server.pem"
     certificate_file = "/usr/local/etc/raddb/certs/server.pem"
     CA_file = "/usr/local/etc/raddb/certs/ca.pem"
     private_key_password = "whatever"
     dh_file = "/usr/local/etc/raddb/certs/dh"
     random_file = "/usr/local/etc/raddb/certs/random"
     fragment_size = 1024
     include_length = yes
     check_crl = no
     cipher_list = "DEFAULT"
     make_cert_command = "/usr/local/etc/raddb/certs/bootstrap"
     cache {
     enable = no
     lifetime = 24
     max_entries = 255
     }
     verify {
     }
     ocsp {
     enable = no
     override_cert_url = yes
     url = "http://127.0.0.1/ocsp/"
     }
    }
  Module: Linked to sub-module rlm_eap_ttls
  Module: Instantiating eap-ttls
    ttls {
     default_eap_type = "md5"
     copy_request_to_tunnel = no
     use_tunneled_reply = no
     virtual_server = "inner-tunnel"
     include_length = yes
    }
  Module: Linked to sub-module rlm_eap_peap
  Module: Instantiating eap-peap
    peap {
     default_eap_type = "mschapv2"
     copy_request_to_tunnel = no
     use_tunneled_reply = no
     proxy_tunneled_request_as_eap = yes
     virtual_server = "inner-tunnel"
     soh = no
    }
  Module: Linked to sub-module rlm_eap_mschapv2
  Module: Instantiating eap-mschapv2
    mschapv2 {
     with_ntdomain_hack = no
     send_error = no
    }
  Module: Checking authorize {...} for more modules to load
  Module: Linked to module rlm_preprocess
  Module: Instantiating module "preprocess" from file
/usr/local/etc/raddb/modules/preprocess
   preprocess {
     huntgroups = "/usr/local/etc/raddb/huntgroups"
     hints = "/usr/local/etc/raddb/hints"
     with_ascend_hack = no
     ascend_channels_per_line = 23
     with_ntdomain_hack = no
     with_specialix_jetstream_hack = no
     with_cisco_vsa_hack = no
     with_alvarion_vsa_hack = no
   }
  Module: Linked to module rlm_wimax
  Module: Instantiating module "wimax" from file
/usr/local/etc/raddb/modules/wimax
   wimax {
     delete_mppe_keys = yes
   }
  Module: Linked to module rlm_realm
  Module: Instantiating module "suffix" from file
/usr/local/etc/raddb/modules/realm
   realm suffix {
     format = "suffix"
     delimiter = "@"
     ignore_default = no
     ignore_null = no
   }
  Module: Linked to module rlm_files
  Module: Instantiating module "files" from file
/usr/local/etc/raddb/modules/files
   files {
     usersfile = "/usr/local/etc/raddb/users"
     acctusersfile = "/usr/local/etc/raddb/acct_users"
     preproxy_usersfile = "/usr/local/etc/raddb/preproxy_users"
     compat = "no"
   }
  Module: Checking preacct {...} for more modules to load
  Module: Loading virtual module acct_unique
  Module: Checking accounting {...} for more modules to load
  Module: Linked to module rlm_detail
  Module: Instantiating module "detail" from file
/usr/local/etc/raddb/modules/detail
   detail {
     detailfile =
"/usr/local/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/detail-%Y%m%d"
     header = "%t"
     detailperm = 384
     dirperm = 493
     locking = no
     log_packet_header = no
   }
  Module: Linked to module rlm_radutmp
  Module: Instantiating module "radutmp" from file
/usr/local/etc/raddb/modules/radutmp
   radutmp {
     filename = "/usr/local/var/log/radius/radutmp"
     username = "%{User-Name}"
     case_sensitive = yes
     check_with_nas = yes
     perm = 384
     callerid = yes
   }
  Module: Linked to module rlm_attr_filter
  Module: Instantiating module "attr_filter.accounting_response" from
file /usr/local/etc/raddb/modules/attr_filter
   attr_filter attr_filter.accounting_response {
     attrsfile = "/usr/local/etc/raddb/attrs.accounting_response"
     key = "%{User-Name}"
     relaxed = no
   }
  Module: Checking session {...} for more modules to load
  Module: Checking post-proxy {...} for more modules to load
  Module: Checking post-auth {...} for more modules to load
  Module: Loading virtual module remove_reply_message_if_eap
  Module: Linked to module rlm_always
  Module: Instantiating module "noop" from file
/usr/local/etc/raddb/modules/always
   always noop {
     rcode = "noop"
     simulcount = 0
     mpp = no
   }
  Module: Instantiating module "attr_filter.access_reject" from file
/usr/local/etc/raddb/modules/attr_filter
   attr_filter attr_filter.access_reject {
     attrsfile = "/usr/local/etc/raddb/attrs.access_reject"
     key = "%{User-Name}"
     relaxed = no
   }
  Module: Loading virtual module remove_reply_message_if_eap
  } # modules
} # server
server inner-tunnel { # from file
/usr/local/etc/raddb/sites-enabled/inner-tunnel
  modules {
  Module: Checking authenticate {...} for more modules to load
  Module: Checking authorize {...} for more modules to load
  Module: Checking session {...} for more modules to load
  Module: Checking post-proxy {...} for more modules to load
  Module: Checking post-auth {...} for more modules to load
  } # modules
} # server
radiusd: #### Opening IP addresses and Ports ####
listen {
     type = "auth"
     ipaddr = *
     port = 0
}
listen {
     type = "acct"
     ipaddr = *
     port = 0
}
listen {
     type = "control"
  listen {
     socket = "/usr/local/var/run/radiusd/radiusd.sock"
  }
}
listen {
     type = "auth"
     ipaddr = 127.0.0.1
     port = 18120
}
Listening on authentication address * port 1812
Listening on accounting address * port 1813
Listening on command file /usr/local/var/run/radiusd/radiusd.sock
Listening on authentication address 127.0.0.1 port 18120 as server
inner-tunnel
Opening new proxy address * port 1814
Listening on proxy address * port 1814
Ready to process requests.
rad_recv: Access-Request packet from host 10.97.0.51 port 49154, id=252,
length=181
     User-Name = "KeepAliveUserNameAndPassword"
     NAS-IP-Address = 10.97.0.51
     NAS-Port-Type = Wireless-802.16
     NAS-Port = 0
     Calling-Station-Id = "\000\000\000\000\000"
     NAS-Identifier = "001001003000096000"
     WiMAX-GMT-Timezone-offset = 0
     Message-Authenticator = 0x07dfa70c37088f55baade217a16d54fc
     Acct-Session-Id = "KeepAliveSessionId"
     User-Password = "KeepAliveUserNameAndPassword"
(0) # Executing section authorize from file
/usr/local/etc/raddb/sites-enabled/default
(0)   group authorize {
(0)  - entering group authorize {...}
(0)   [preprocess] = ok
(0)   [chap] = noop
(0)   [mschap] = noop
(0)   [digest] = noop
rlm_wimax: Fixing WiMAX binary Calling-Station-Id to 00-00-00-00-00-00
(0)   [wimax] = ok
(0) suffix : No '@' in User-Name = "KeepAliveUserNameAndPassword",
looking up realm NULL
(0) suffix : No such realm "NULL"
(0)   [suffix] = noop
(0) eap : No EAP-Message, not doing EAP
(0)   [eap] = noop
(0) files : users: Matched entry KeepAliveUserNameAndPassword at line 7
(0)   [files] = ok
(0)   [expiration] = noop
(0)   [logintime] = noop
(0)   [pap] = updated
(0) Found Auth-Type = PAP
(0) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(0)   group PAP {
(0)  - entering group PAP {...}
(0) pap : login attempt with password "KeepAliveUserNameAndPassword"
(0) pap : Using clear text password "KeepAliveUserNameAndPassword"
(0) pap : User authenticated successfully
(0)   [pap] = ok
(0) # Executing section post-auth from file
/usr/local/etc/raddb/sites-enabled/default
(0)   group post-auth {
(0)  - entering group post-auth {...}
(0)   [exec] = noop
(0)   update request {
(0)     expand: %{User-Name} ->  KeepAliveUserNameAndPassword
(0)   } # update request = noop
(0)   update reply {
(0)     expand: %{EAP-MSK} ->
(0)   } # update reply = noop
(0) wimax : No EAP-MSK or EAP-EMSK.  Cannot create WiMAX keys.
(0)   [wimax] = noop
(0)    policy remove_reply_message_if_eap {
(0)   - entering policy remove_reply_message_if_eap {...}
(0)    ? if (reply:EAP-Message&&  reply:Reply-Message)
(0) ? Evaluating (reply:EAP-Message ) ->  FALSE
(0) ? Skipping (reply:Reply-Message)
(0)    ? if (reply:EAP-Message&&  reply:Reply-Message) ->  FALSE
(0)     else else {
(0)    - entering else else {...}
(0)     [noop] = noop
(0)    - else else returns noop
(0)   - policy remove_reply_message_if_eap returns noop
Sending Access-Accept of id 252 to 10.97.0.51 port 49154
     Filter-Id = "SP=sp1:MSF=msf1;SP=sp_data_eth:MSF=msf_data_eth;"
     Session-Timeout = 1200
     Termination-Action = RADIUS-Request
     WiMAX-FA-RK-Key = 0x00
     WiMAX-MSK = 0x
WARNING: Skipping zero-length attribute WiMAX-MSK
(0) Finished request 0.
Waking up in 0.3 seconds.
Waking up in 4.6 seconds.
(0) Cleaning up request packet ID 252 with timestamp +1
Ready to process requests.
rad_recv: Access-Request packet from host 10.97.0.51 port 49154, id=253,
length=258
     User-Name = "{am=1}8ea39298d98b6189e0aad92594970151@WIMAX.COM"
     NAS-IP-Address = 10.97.0.51
     NAS-Port-Type = Wireless-802.16
     NAS-Port = 1
     Calling-Station-Id = "\000\020\347a\r\226"
     NAS-Identifier = "001001003000096000"
     WiMAX-GMT-Timezone-offset = 0
     Framed-MTU = 1490
     Service-Type = Framed-User
     WiMAX-Release = "1.0"
     WiMAX-Accounting-Capabilities = IP-Session-Based
     WiMAX-BS-Id = 0x303031303031303033303030303936303030
     EAP-Message =
0x02010035017b616d3d317d38656133393239386439386236313839653061616439323539343937303135314057494d41582e434f4d
     Message-Authenticator = 0x6a08e376952afbaf0740a456767bfe80
(1) # Executing section authorize from file
/usr/local/etc/raddb/sites-enabled/default
(1)   group authorize {
(1)  - entering group authorize {...}
(1)   [preprocess] = ok
(1)   [chap] = noop
(1)   [mschap] = noop
(1)   [digest] = noop
rlm_wimax: Fixing WiMAX binary Calling-Station-Id to 00-10-e7-61-0d-96
(1)   [wimax] = ok
(1) suffix : Looking up realm "WIMAX.COM" for User-Name =
"{am=1}8ea39298d98b6189e0aad92594970151@WIMAX.COM"
(1) suffix : No such realm "WIMAX.COM"
(1)   [suffix] = noop
(1) eap : EAP packet type response id 1 length 53
(1) eap : EAP-Identity reply, returning 'ok' so we can short-circuit the
rest of authorize
(1)   [eap] = ok
(1) Found Auth-Type = EAP
(1) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(1)   group authenticate {
(1)  - entering group authenticate {...}
(1) eap : EAP Identity
(1) eap : processing type md5
rlm_eap_md5: Issuing Challenge
(1)   [eap] = handled
Sending Access-Challenge of id 253 to 10.97.0.51 port 49154
     EAP-Message = 0x010200160410d780646d179a777255c505dfbee44ab4
     Message-Authenticator = 0x00000000000000000000000000000000
     State = 0xee37a64fee35a255d3718fb2df57c86c
(1) Finished request 1.
Waking up in 0.3 seconds.
rad_recv: Access-Request packet from host 10.97.0.51 port 49154, id=254,
length=229
     User-Name = "{am=1}8ea39298d98b6189e0aad92594970151@WIMAX.COM"
     NAS-IP-Address = 10.97.0.51
     NAS-Port-Type = Wireless-802.16
     NAS-Port = 1
     Calling-Station-Id = "\000\020\347a\r\226"
     NAS-Identifier = "001001003000096000"
     WiMAX-GMT-Timezone-offset = 0
     Framed-MTU = 1490
     Service-Type = Framed-User
     State = 0xee37a64fee35a255d3718fb2df57c86c
     WiMAX-Release = "1.0"
     WiMAX-Accounting-Capabilities = IP-Session-Based
     WiMAX-BS-Id = 0x303031303031303033303030303936303030
     EAP-Message = 0x020200060315
     Message-Authenticator = 0x94447e93f95cc98a8a6c227ccd901efe
(2) # Executing section authorize from file
/usr/local/etc/raddb/sites-enabled/default
(2)   group authorize {
(2)  - entering group authorize {...}
(2)   [preprocess] = ok
(2)   [chap] = noop
(2)   [mschap] = noop
(2)   [digest] = noop
rlm_wimax: Fixing WiMAX binary Calling-Station-Id to 00-10-e7-61-0d-96
(2)   [wimax] = ok
(2) suffix : Looking up realm "WIMAX.COM" for User-Name =
"{am=1}8ea39298d98b6189e0aad92594970151@WIMAX.COM"
(2) suffix : No such realm "WIMAX.COM"
(2)   [suffix] = noop
(2) eap : EAP packet type response id 2 length 6
(2) eap : No EAP Start, assuming it's an on-going EAP conversation
(2)   [eap] = updated
(2)   [files] = noop
(2)   [expiration] = noop
(2)   [logintime] = noop
(2) pap : WARNING! No "known good" password found for the user.
Authentication may fail because of this.
(2)   [pap] = noop
(2) Found Auth-Type = EAP
(2) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(2)   group authenticate {
(2)  - entering group authenticate {...}
(2) eap : Request found, released from the list
(2) eap : EAP NAK
(2) eap : EAP-NAK asked for EAP-Type/ttls
(2) eap : processing type tls
(2) tls : Initiate
(2) tls : Start returned 1
(2)   [eap] = handled
Sending Access-Challenge of id 254 to 10.97.0.51 port 49154
     EAP-Message = 0x010300061520
     Message-Authenticator = 0x00000000000000000000000000000000
     State = 0xee37a64fef34b355d3718fb2df57c86c
(2) Finished request 2.
Waking up in 0.1 seconds.
rad_recv: Access-Request packet from host 10.97.0.51 port 49154, id=255,
length=285
     User-Name = "{am=1}8ea39298d98b6189e0aad92594970151@WIMAX.COM"
     NAS-IP-Address = 10.97.0.51
     NAS-Port-Type = Wireless-802.16
     NAS-Port = 1
     Calling-Station-Id = "\000\020\347a\r\226"
     NAS-Identifier = "001001003000096000"
     WiMAX-GMT-Timezone-offset = 0
     Framed-MTU = 1490
     Service-Type = Framed-User
     State = 0xee37a64fef34b355d3718fb2df57c86c
     WiMAX-Release = "1.0"
     WiMAX-Accounting-Capabilities = IP-Session-Based
     WiMAX-BS-Id = 0x303031303031303033303030303936303030
     EAP-Message =
0x0203003e150016030100330100002f0301000006dea50c9829a6d3f565bcdf7456521cc6099d8b828e302b1e2dce4a70e7000008002f000a000500040100
     Message-Authenticator = 0xd86dddc0e2ef35284fb32302bf1daedf
(3) # Executing section authorize from file
/usr/local/etc/raddb/sites-enabled/default
(3)   group authorize {
(3)  - entering group authorize {...}
(3)   [preprocess] = ok
(3)   [chap] = noop
(3)   [mschap] = noop
(3)   [digest] = noop
rlm_wimax: Fixing WiMAX binary Calling-Station-Id to 00-10-e7-61-0d-96
(3)   [wimax] = ok
(3) suffix : Looking up realm "WIMAX.COM" for User-Name =
"{am=1}8ea39298d98b6189e0aad92594970151@WIMAX.COM"
(3) suffix : No such realm "WIMAX.COM"
(3)   [suffix] = noop
(3) eap : EAP packet type response id 3 length 62
(3) eap : Continuing tunnel setup.
(3)   [eap] = ok
(3) Found Auth-Type = EAP
(3) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(3)   group authenticate {
(3)  - entering group authenticate {...}
(3) eap : Request found, released from the list
(3) eap : EAP/ttls
(3) eap : processing type ttls
(3) ttls : Authenticate
(3) ttls : processing EAP-TLS
(3) ttls : eaptls_verify returned 7
(3) ttls : Done initial handshake
(3) ttls :     (other): before/accept initialization
(3) ttls :     TLS_accept: before/accept initialization
(3) ttls :<<<  TLS 1.0 Handshake [length 0033], ClientHello
(3) ttls :     TLS_accept: SSLv3 read client hello A
(3) ttls :>>>  TLS 1.0 Handshake [length 002a], ServerHello
(3) ttls :     TLS_accept: SSLv3 write server hello A
(3) ttls :>>>  TLS 1.0 Handshake [length 085e], Certificate
(3) ttls :     TLS_accept: SSLv3 write certificate A
(3) ttls :>>>  TLS 1.0 Handshake [length 0004], ServerHelloDone
(3) ttls :     TLS_accept: SSLv3 write server done A
(3) ttls :     TLS_accept: SSLv3 flush data
(3) ttls :     TLS_accept: Need to read more data: SSLv3 read client
certificate A
In SSL Handshake Phase
In SSL Accept mode
(3) ttls : eaptls_process returned 13
(3)   [eap] = handled
Sending Access-Challenge of id 255 to 10.97.0.51 port 49154
     EAP-Message =
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
     EAP-Message =
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
     EAP-Message =
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
     EAP-Message =
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
     EAP-Message = 0xa73082038fa0030201020209
     Message-Authenticator = 0x00000000000000000000000000000000
     State = 0xee37a64fec33b355d3718fb2df57c86c
(3) Finished request 3.
Waking up in 0.1 seconds.
rad_recv: Access-Request packet from host 10.97.0.51 port 49154, id=0,
length=229
     User-Name = "{am=1}8ea39298d98b6189e0aad92594970151@WIMAX.COM"
     NAS-IP-Address = 10.97.0.51
     NAS-Port-Type = Wireless-802.16
     NAS-Port = 1
     Calling-Station-Id = "\000\020\347a\r\226"
     NAS-Identifier = "001001003000096000"
     WiMAX-GMT-Timezone-offset = 0
     Framed-MTU = 1490
     Service-Type = Framed-User
     State = 0xee37a64fec33b355d3718fb2df57c86c
     WiMAX-Release = "1.0"
     WiMAX-Accounting-Capabilities = IP-Session-Based
     WiMAX-BS-Id = 0x303031303031303033303030303936303030
     EAP-Message = 0x020400061500
     Message-Authenticator = 0xd9761a90cc87c962fd3b1d9ba3d5c37b
(4) # Executing section authorize from file
/usr/local/etc/raddb/sites-enabled/default
(4)   group authorize {
(4)  - entering group authorize {...}
(4)   [preprocess] = ok
(4)   [chap] = noop
(4)   [mschap] = noop
(4)   [digest] = noop
rlm_wimax: Fixing WiMAX binary Calling-Station-Id to 00-10-e7-61-0d-96
(4)   [wimax] = ok
(4) suffix : Looking up realm "WIMAX.COM" for User-Name =
"{am=1}8ea39298d98b6189e0aad92594970151@WIMAX.COM"
(4) suffix : No such realm "WIMAX.COM"
(4)   [suffix] = noop
(4) eap : EAP packet type response id 4 length 6
(4) eap : Continuing tunnel setup.
(4)   [eap] = ok
(4) Found Auth-Type = EAP
(4) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(4)   group authenticate {
(4)  - entering group authenticate {...}
(4) eap : Request found, released from the list
(4) eap : EAP/ttls
(4) eap : processing type ttls
(4) ttls : Authenticate
(4) ttls : processing EAP-TLS
(4) ttls : Received TLS ACK
(4) ttls : Received TLS ACK
(4) ttls : ACK handshake fragment handler
(4) ttls : eaptls_verify returned 1
(4) ttls : eaptls_process returned 13
(4)   [eap] = handled
Sending Access-Challenge of id 0 to 10.97.0.51 port 49154
     EAP-Message =
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
     EAP-Message =
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
     EAP-Message =
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
     EAP-Message =
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
     EAP-Message = 0xf882cb62abfb0d6232ed28a9
     Message-Authenticator = 0x00000000000000000000000000000000
     State = 0xee37a64fed32b355d3718fb2df57c86c
(4) Finished request 4.
Waking up in 0.1 seconds.
Waking up in 0.1 seconds.
rad_recv: Access-Request packet from host 10.97.0.51 port 49154, id=1,
length=229
     User-Name = "{am=1}8ea39298d98b6189e0aad92594970151@WIMAX.COM"
     NAS-IP-Address = 10.97.0.51
     NAS-Port-Type = Wireless-802.16
     NAS-Port = 1
     Calling-Station-Id = "\000\020\347a\r\226"
     NAS-Identifier = "001001003000096000"
     WiMAX-GMT-Timezone-offset = 0
     Framed-MTU = 1490
     Service-Type = Framed-User
     State = 0xee37a64fed32b355d3718fb2df57c86c
     WiMAX-Release = "1.0"
     WiMAX-Accounting-Capabilities = IP-Session-Based
     WiMAX-BS-Id = 0x303031303031303033303030303936303030
     EAP-Message = 0x020500061500
     Message-Authenticator = 0xef737a5a4bd7ccef3fc0193c76fed73d
(5) # Executing section authorize from file
/usr/local/etc/raddb/sites-enabled/default
(5)   group authorize {
(5)  - entering group authorize {...}
(5)   [preprocess] = ok
(5)   [chap] = noop
(5)   [mschap] = noop
(5)   [digest] = noop
rlm_wimax: Fixing WiMAX binary Calling-Station-Id to 00-10-e7-61-0d-96
(5)   [wimax] = ok
(5) suffix : Looking up realm "WIMAX.COM" for User-Name =
"{am=1}8ea39298d98b6189e0aad92594970151@WIMAX.COM"
(5) suffix : No such realm "WIMAX.COM"
(5)   [suffix] = noop
(5) eap : EAP packet type response id 5 length 6
(5) eap : Continuing tunnel setup.
(5)   [eap] = ok
(5) Found Auth-Type = EAP
(5) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(5)   group authenticate {
(5)  - entering group authenticate {...}
(5) eap : Request found, released from the list
(5) eap : EAP/ttls
(5) eap : processing type ttls
(5) ttls : Authenticate
(5) ttls : processing EAP-TLS
(5) ttls : Received TLS ACK
(5) ttls : Received TLS ACK
(5) ttls : ACK handshake fragment handler
(5) ttls : eaptls_verify returned 1
(5) ttls : eaptls_process returned 13
(5)   [eap] = handled
Sending Access-Challenge of id 1 to 10.97.0.51 port 49154
     EAP-Message =
0x010600b915800000089b3d2597e37be612302c51251c809caf06efe13344d68deb5cfd8abbb0ccb8daabe346f1179e51544bb2960cedde88c033d1f68539aaad5f0078a4144e8441407e8f86570400d136f23320d86712d4dbd9887b5d892b7bf71c7fc3862e967c7f8cbfe752971cd38a7a895000823e4166edfe4442df305d728337b4dcd7e4f6d7be981bf5e48730b79fb5500dd8da4ad2db24cda20ad7723b61dd6526cb5d5f724d15c1d73eef0c16030100040e000000
     Message-Authenticator = 0x00000000000000000000000000000000
     State = 0xee37a64fea31b355d3718fb2df57c86c
(5) Finished request 5.
Waking up in 0.1 seconds.
Waking up in 0.1 seconds.
Waking up in 4.0 seconds.
rad_recv: Access-Request packet from host 10.97.0.51 port 49154, id=2,
length=557
     User-Name = "{am=1}8ea39298d98b6189e0aad92594970151@WIMAX.COM"
     NAS-IP-Address = 10.97.0.51
     NAS-Port-Type = Wireless-802.16
     NAS-Port = 1
     Calling-Station-Id = "\000\020\347a\r\226"
     NAS-Identifier = "001001003000096000"
     WiMAX-GMT-Timezone-offset = 0
     Framed-MTU = 1490
     Service-Type = Framed-User
     State = 0xee37a64fea31b355d3718fb2df57c86c
     WiMAX-Release = "1.0"
     WiMAX-Accounting-Capabilities = IP-Session-Based
     WiMAX-BS-Id = 0x303031303031303033303030303936303030
     EAP-Message =
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
     EAP-Message =
0x0edc306e48ce048e02c2add34f74027fdcfb6e271403010001011603010030ea083b041af212a12ae8ffbd04ad129aad64aa9b57e6b0c8a6bcf22be74cababaaa5c3bcd230bab51d055fee3380a470
     Message-Authenticator = 0x5397dd3676e023551a225bcd4c9b4841
(6) # Executing section authorize from file
/usr/local/etc/raddb/sites-enabled/default
(6)   group authorize {
(6)  - entering group authorize {...}
(6)   [preprocess] = ok
(6)   [chap] = noop
(6)   [mschap] = noop
(6)   [digest] = noop
rlm_wimax: Fixing WiMAX binary Calling-Station-Id to 00-10-e7-61-0d-96
(6)   [wimax] = ok
(6) suffix : Looking up realm "WIMAX.COM" for User-Name =
"{am=1}8ea39298d98b6189e0aad92594970151@WIMAX.COM"
(6) suffix : No such realm "WIMAX.COM"
(6)   [suffix] = noop
(6) eap : EAP packet type response id 6 length 253
(6) eap : Continuing tunnel setup.
(6)   [eap] = ok
(6) Found Auth-Type = EAP
(6) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(6)   group authenticate {
(6)  - entering group authenticate {...}
(6) eap : Request found, released from the list
(6) eap : EAP/ttls
(6) eap : processing type ttls
(6) ttls : Authenticate
(6) ttls : processing EAP-TLS
(6) ttls : eaptls_verify returned 7
(6) ttls : Done initial handshake
(6) ttls :<<<  TLS 1.0 Handshake [length 0106], ClientKeyExchange
(6) ttls :     TLS_accept: SSLv3 read client key exchange A
(6) ttls :<<<  TLS 1.0 ChangeCipherSpec [length 0001]
(6) ttls :<<<  TLS 1.0 Handshake [length 0010], Finished
(6) ttls :     TLS_accept: SSLv3 read finished A
(6) ttls :>>>  TLS 1.0 ChangeCipherSpec [length 0001]
(6) ttls :     TLS_accept: SSLv3 write change cipher spec A
(6) ttls :>>>  TLS 1.0 Handshake [length 0010], Finished
(6) ttls :     TLS_accept: SSLv3 write finished A
(6) ttls :     TLS_accept: SSLv3 flush data
(6) ttls :     (other): SSL negotiation finished successfully
SSL Connection Established
(6) ttls : eaptls_process returned 13
(6)   [eap] = handled
Sending Access-Challenge of id 2 to 10.97.0.51 port 49154
     EAP-Message =
0x0107004515800000003b14030100010116030100304d77d31f3558219cd2d5d05b8c42db32a2ce0d6bd1da6e97e38197f17d4eac78e578974e0c3354ea36b515b5476332ab
     Message-Authenticator = 0x00000000000000000000000000000000
     State = 0xee37a64feb30b355d3718fb2df57c86c
(6) Finished request 6.
Waking up in 0.3 seconds.
rad_recv: Access-Request packet from host 10.97.0.51 port 49154, id=3,
length=378
     User-Name = "{am=1}8ea39298d98b6189e0aad92594970151@WIMAX.COM"
     NAS-IP-Address = 10.97.0.51
     NAS-Port-Type = Wireless-802.16
     NAS-Port = 1
     Calling-Station-Id = "\000\020\347a\r\226"
     NAS-Identifier = "001001003000096000"
     WiMAX-GMT-Timezone-offset = 0
     Framed-MTU = 1490
     Service-Type = Framed-User
     State = 0xee37a64feb30b355d3718fb2df57c86c
     WiMAX-Release = "1.0"
     WiMAX-Accounting-Capabilities = IP-Session-Based
     WiMAX-BS-Id = 0x303031303031303033303030303936303030
     EAP-Message =
0x0207009b15001703010090a94a44a2a1a24b0a0392b385be4c524085fc4dfb58cfba7623fc7c790c2d41fc76e98554be526ca2c8006d0a629f426c5d5c33fe724c6ca3081b7c85e42a4d265a64e46174b8351f823a47031ffb562df9f92c6215742d6a8bde1501cbd573142fc18b05197ceb050886a163d0984703554fb9281a249d8037c2e80197f4fc14eca539d1dfa4058805d16490ba6e92cd
     Message-Authenticator = 0x0ea984d0f33d209c0596706209586ebe
(7) # Executing section authorize from file
/usr/local/etc/raddb/sites-enabled/default
(7)   group authorize {
(7)  - entering group authorize {...}
(7)   [preprocess] = ok
(7)   [chap] = noop
(7)   [mschap] = noop
(7)   [digest] = noop
rlm_wimax: Fixing WiMAX binary Calling-Station-Id to 00-10-e7-61-0d-96
(7)   [wimax] = ok
(7) suffix : Looking up realm "WIMAX.COM" for User-Name =
"{am=1}8ea39298d98b6189e0aad92594970151@WIMAX.COM"
(7) suffix : No such realm "WIMAX.COM"
(7)   [suffix] = noop
(7) eap : EAP packet type response id 7 length 155
(7) eap : Continuing tunnel setup.
(7)   [eap] = ok
(7) Found Auth-Type = EAP
(7) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(7)   group authenticate {
(7)  - entering group authenticate {...}
(7) eap : Request found, released from the list
(7) eap : EAP/ttls
(7) eap : processing type ttls
(7) ttls : Authenticate
(7) ttls : processing EAP-TLS
(7) ttls : eaptls_verify returned 7
(7) ttls : Done initial handshake
(7) ttls : eaptls_process returned 7
(7) ttls : Session established.  Proceeding to decode tunneled attributes.
(7) ttls : Got tunneled request
     User-Name = "wimax1@WIMAX.COM"
     MS-CHAP-Challenge = 0x4ff634da70572b920e78e38be8977202
     MS-CHAP2-Response =
0x6c00bb3a20c2232fc139ef8b9c65b557b75400000000000000005bc93665692787af9c594fc9bc1c22709773fbba940e5ba8
     FreeRADIUS-Proxied-To = 127.0.0.1
(7) ttls : Sending tunneled request
     User-Name = "wimax1@WIMAX.COM"
     MS-CHAP-Challenge = 0x4ff634da70572b920e78e38be8977202
     MS-CHAP2-Response =
0x6c00bb3a20c2232fc139ef8b9c65b557b75400000000000000005bc93665692787af9c594fc9bc1c22709773fbba940e5ba8
     FreeRADIUS-Proxied-To = 127.0.0.1
server inner-tunnel {
(7) # Executing section authorize from file
/usr/local/etc/raddb/sites-enabled/inner-tunnel
(7)   group authorize {
(7)  - entering group authorize {...}
(7)   [chap] = noop
(7) mschap : Found MS-CHAP attributes.  Setting 'Auth-Type  = mschap'
(7)   [mschap] = ok
(7) suffix : Looking up realm "WIMAX.COM" for User-Name = "wimax1@WIMAX.COM"
(7) suffix : No such realm "WIMAX.COM"
(7)   [suffix] = noop
(7)   update control {
(7)   } # update control = noop
(7) eap : No EAP-Message, not doing EAP
(7)   [eap] = noop
(7) files : users: Matched entry wimax1@WIMAX.COM at line 4
(7)   [files] = ok
(7)   [expiration] = noop
(7)   [logintime] = noop
(7) pap : WARNING: Auth-Type already set.  Not setting to PAP
(7)   [pap] = noop
(7) Found Auth-Type = MSCHAP
(7) # Executing group from file
/usr/local/etc/raddb/sites-enabled/inner-tunnel
(7)   group MS-CHAP {
(7)  - entering group MS-CHAP {...}
(7) mschap : Creating challenge hash with username: wimax1@WIMAX.COM
(7) mschap : Told to do MS-CHAPv2 for wimax1@WIMAX.COM with NT-Password
(7) mschap : adding MS-CHAPv2 MPPE keys
(7)   [mschap] = ok
(7)   WARNING: Empty post-auth section.  Using default return values.
(7) # Executing section post-auth from file
/usr/local/etc/raddb/sites-enabled/inner-tunnel
} # server inner-tunnel
(7) ttls : Got tunneled reply code 2
     Filter-Id = "SP=sp1:MSF=msf1;SP=sp_data_eth:MSF=msf_data_eth;"
     Session-Timeout = 1200
     Termination-Action = RADIUS-Request
     MS-CHAP2-Success =
0x6c533d30413343343445383339364636373237324330443444433632433932413444393239444146314633
     MS-MPPE-Recv-Key = 0x9efd76988038d3ccf4f6ab6aa211af6c
     MS-MPPE-Send-Key = 0x2b74cab7d6bdc6e763f480864a5c581b
     MS-MPPE-Encryption-Policy = Encryption-Allowed
     MS-MPPE-Encryption-Types = RC4-40or128-bit-Allowed
(7) ttls : Got tunneled Access-Accept
(7) ttls : Got MS-CHAP2-Success, tunneling it to the client in a challenge.
(7)   [eap] = handled
Sending Access-Challenge of id 3 to 10.97.0.51 port 49154
     EAP-Message =
0x0108005f158000000055170301005062cd34a1fec097a2061cc98ee4632f597a42ed4cd80a2d7a7e84c06929acba192114c44395bb6e676d6529843c7618fe2ebe29a179e7ed8f1cfa6692e8c775760daca68609f7893158eef62a49fba9eb
     Message-Authenticator = 0x00000000000000000000000000000000
     State = 0xee37a64fe83fb355d3718fb2df57c86c
(7) Finished request 7.
Waking up in 0.1 seconds.
Waking up in 0.1 seconds.
rad_recv: Access-Request packet from host 10.97.0.51 port 49154, id=4,
length=229
     User-Name = "{am=1}8ea39298d98b6189e0aad92594970151@WIMAX.COM"
     NAS-IP-Address = 10.97.0.51
     NAS-Port-Type = Wireless-802.16
     NAS-Port = 1
     Calling-Station-Id = "\000\020\347a\r\226"
     NAS-Identifier = "001001003000096000"
     WiMAX-GMT-Timezone-offset = 0
     Framed-MTU = 1490
     Service-Type = Framed-User
     State = 0xee37a64fe83fb355d3718fb2df57c86c
     WiMAX-Release = "1.0"
     WiMAX-Accounting-Capabilities = IP-Session-Based
     WiMAX-BS-Id = 0x303031303031303033303030303936303030
     EAP-Message = 0x020800061500
     Message-Authenticator = 0xf409f172ed2561c15ab0cbef54e4d1a2
(8) # Executing section authorize from file
/usr/local/etc/raddb/sites-enabled/default
(8)   group authorize {
(8)  - entering group authorize {...}
(8)   [preprocess] = ok
(8)   [chap] = noop
(8)   [mschap] = noop
(8)   [digest] = noop
rlm_wimax: Fixing WiMAX binary Calling-Station-Id to 00-10-e7-61-0d-96
(8)   [wimax] = ok
(8) suffix : Looking up realm "WIMAX.COM" for User-Name =
"{am=1}8ea39298d98b6189e0aad92594970151@WIMAX.COM"
(8) suffix : No such realm "WIMAX.COM"
(8)   [suffix] = noop
(8) eap : EAP packet type response id 8 length 6
(8) eap : Continuing tunnel setup.
(8)   [eap] = ok
(8) Found Auth-Type = EAP
(8) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(8)   group authenticate {
(8)  - entering group authenticate {...}
(8) eap : Request found, released from the list
(8) eap : EAP/ttls
(8) eap : processing type ttls
(8) ttls : Authenticate
(8) ttls : processing EAP-TLS
(8) ttls : Received TLS ACK
(8) ttls : Received TLS ACK
(8) ttls : ACK handshake is finished
(8) ttls : eaptls_verify returned 3
(8) ttls : eaptls_process returned 3
(8) ttls : Using saved attributes from the original Access-Accept
(8) eap : Freeing handler
(8)   [eap] = ok
(8) # Executing section post-auth from file
/usr/local/etc/raddb/sites-enabled/default
(8)   group post-auth {
(8)  - entering group post-auth {...}
(8)   [exec] = noop
(8)   update request {
(8)     expand: %{User-Name} ->
{am=1}8ea39298d98b6189e0aad92594970151@WIMAX.COM
(8)   } # update request = noop
(8)   update reply {
(8)     expand: %{EAP-MSK} ->
(8)   } # update reply = noop
(8) wimax : MIP-RK =
0xa2cd93eabee4a9a935f0933e2f37c957da9234590d87e33821a353a732f73a28696ae2171e51289b41207e8558e941db6193526d4f6b70ebc740e44c08cae189
(8) wimax : MIP-SPI = d57e2db6
(8) wimax : WARNING: WiMAX-IP-Technology not found in reply.
(8) wimax : WARNING: Not calculating MN-HA keys
(8)   [wimax] = updated
(8)    policy remove_reply_message_if_eap {
(8)   - entering policy remove_reply_message_if_eap {...}
(8)    ? if (reply:EAP-Message&&  reply:Reply-Message)
(8) ? Evaluating (reply:EAP-Message ) ->  TRUE
(8) ? Evaluating (reply:Reply-Message) ->  FALSE
(8)    ? if (reply:EAP-Message&&  reply:Reply-Message) ->  FALSE
(8)     else else {
(8)    - entering else else {...}
(8)     [noop] = noop
(8)    - else else returns noop
(8)   - policy remove_reply_message_if_eap returns noop
Sending Access-Accept of id 4 to 10.97.0.51 port 49154
     EAP-Message = 0x03080004
     Message-Authenticator = 0x00000000000000000000000000000000
     User-Name = "{am=1}8ea39298d98b6189e0aad92594970151@WIMAX.COM"
     WiMAX-FA-RK-Key = 0x9081b1490484318c46d65476645a3ea806798046
     WiMAX-MSK = 0x
WARNING: Skipping zero-length attribute WiMAX-MSK
     WiMAX-MSK =
0x0d156b72753d155483788273ff85ed2c67c724fc8e5cbcacee65caeaf5cfff7c62b3f42371331bc2efc2694834c80ad4ba4fe730f9b434c4726a22b5c2c39ecb
     WiMAX-FA-RK-SPI = 3056434901
(8) Finished request 8.
Waking up in 0.1 seconds.
Waking up in 0.1 seconds.
Waking up in 3.3 seconds.
(1) Cleaning up request packet ID 253 with timestamp +48
Waking up in 0.1 seconds.
(2) Cleaning up request packet ID 254 with timestamp +48
Waking up in 0.1 seconds.
(3) Cleaning up request packet ID 255 with timestamp +48
Waking up in 0.1 seconds.
(4) Cleaning up request packet ID 0 with timestamp +48
Waking up in 0.1 seconds.
(5) Cleaning up request packet ID 1 with timestamp +48
Waking up in 0.3 seconds.
(6) Cleaning up request packet ID 2 with timestamp +49
Waking up in 0.1 seconds.
(7) Cleaning up request packet ID 3 with timestamp +49
Waking up in 0.1 seconds.
(8) Cleaning up request packet ID 4 with timestamp +49
Ready to process requests.

alvarion not receiving Filter-Id parameters

Bruce Eckstein