Hello everyone! I’m writing here because of a problem I’m having trying to do a specific thing with FreeRADIUS 3.0.17. For a university project, I need to setup a malicious access point that lets everyone connect to its Wi-Fi network in order to perform some traffic analysis. Previously, using FreeRADIUS v2.2.8 I managed to do this by simply putting update control { Auth-Type := Accept } in the authorize section of the inner-tunnel. Everything worked fine and I could connect to the Wi-Fi network using any combination of username, password and authentication method (PEAP/TTLS for phase 1 and any other method in phase 2). Recently, however, I had to switch to a Raspberry Pi 3B+ to use as access point. Here I downloaded the 3.0.17 version, which is the only one available through apt-get. Configuring v3.0.17 in the same way I did with v.2.2.8, however, I get really weird results. Basically, using iOS (14, but I don’t think it’s a matter of version) I can still connect to the same Wi-Fi using any username and password. If I use Android, instead, I can’t connect even using the correct password. A subportion of the logs I get from running in debug mode is this one: (8) eap_peap: Session established. Decoding tunneled attributes (8) eap_peap: PEAP state send tlv success (8) eap_peap: Received EAP-TLV response (8) eap_peap: Client rejected our response. The password is probably incorrect (8) eap_peap: ERROR: We sent a success, but the client did not agree (8) eap: ERROR: Failed continuing EAP PEAP (25) session. EAP sub-module failed (8) eap: Sending EAP Failure (code 4) ID 179 length 4 The log in its entirety is attached at the end of this post. So FreeRADIUS sends an Access Accept, but the mobile phone rejects it. Again, this only happens with Android smartphones, not with iPhones. The method I use, now only works for TTLS/PAP, not for PEAP or TTLS/MSCHAP. Is there still a way to accomplish what I could do in v2.2.8 but in v.3.0.17? Did anybody notice a different behavior between iOS and Android smartphones? Thanks everyone! pi@raspberrypi:/etc/freeradius/3.0 $ sudo freeradius -X FreeRADIUS Version 3.0.17 Copyright (C) 1999-2017 The FreeRADIUS server project and contributors There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE You may redistribute copies of FreeRADIUS under the terms of the GNU General Public License For more information about these matters, see the file named COPYRIGHT Starting - reading configuration files ... including dictionary file /usr/share/freeradius/dictionary including dictionary file /usr/share/freeradius/dictionary.dhcp including dictionary file /usr/share/freeradius/dictionary.vqp including dictionary file /etc/freeradius/3.0/dictionary including configuration file /etc/freeradius/3.0/radiusd.conf including configuration file /etc/freeradius/3.0/proxy.conf including configuration file /etc/freeradius/3.0/clients.conf including files in directory /etc/freeradius/3.0/mods-enabled/ including configuration file /etc/freeradius/3.0/mods-enabled/eap including configuration file /etc/freeradius/3.0/mods-enabled/utf8 including configuration file /etc/freeradius/3.0/mods-enabled/expr including configuration file /etc/freeradius/3.0/mods-enabled/detail including configuration file /etc/freeradius/3.0/mods-enabled/attr_filter including configuration file /etc/freeradius/3.0/mods-enabled/exec including configuration file /etc/freeradius/3.0/mods-enabled/soh including configuration file /etc/freeradius/3.0/mods-enabled/dynamic_clients including configuration file /etc/freeradius/3.0/mods-enabled/add_user including configuration file /etc/freeradius/3.0/mods-enabled/passwd including configuration file /etc/freeradius/3.0/mods-enabled/detail.log including configuration file /etc/freeradius/3.0/mods-enabled/unpack including configuration file /etc/freeradius/3.0/mods-enabled/always including configuration file /etc/freeradius/3.0/mods-enabled/cache_eap including configuration file /etc/freeradius/3.0/mods-enabled/digest including configuration file /etc/freeradius/3.0/mods-enabled/pap including configuration file /etc/freeradius/3.0/mods-enabled/mschap including configuration file /etc/freeradius/3.0/mods-enabled/ntlm_auth including configuration file /etc/freeradius/3.0/mods-enabled/realm including configuration file /etc/freeradius/3.0/mods-enabled/logintime including configuration file /etc/freeradius/3.0/mods-enabled/linelog including configuration file /etc/freeradius/3.0/mods-enabled/expiration including configuration file /etc/freeradius/3.0/mods-enabled/chap including configuration file /etc/freeradius/3.0/mods-enabled/files including configuration file /etc/freeradius/3.0/mods-enabled/replicate including configuration file /etc/freeradius/3.0/mods-enabled/add_user_pap including configuration file /etc/freeradius/3.0/mods-enabled/radutmp including configuration file /etc/freeradius/3.0/mods-enabled/unix including configuration file /etc/freeradius/3.0/mods-enabled/echo including configuration file /etc/freeradius/3.0/mods-enabled/preprocess including configuration file /etc/freeradius/3.0/mods-enabled/sradutmp including files in directory /etc/freeradius/3.0/policy.d/ including configuration file /etc/freeradius/3.0/policy.d/eap including configuration file /etc/freeradius/3.0/policy.d/canonicalization including configuration file /etc/freeradius/3.0/policy.d/cui including configuration file /etc/freeradius/3.0/policy.d/operator-name including configuration file /etc/freeradius/3.0/policy.d/filter including configuration file /etc/freeradius/3.0/policy.d/moonshot-targeted-ids including configuration file /etc/freeradius/3.0/policy.d/dhcp including configuration file /etc/freeradius/3.0/policy.d/debug including configuration file /etc/freeradius/3.0/policy.d/control including configuration file /etc/freeradius/3.0/policy.d/abfab-tr including configuration file /etc/freeradius/3.0/policy.d/accounting including files in directory /etc/freeradius/3.0/sites-enabled/ including configuration file /etc/freeradius/3.0/sites-enabled/default including configuration file /etc/freeradius/3.0/sites-enabled/inner-tunnel main { security { user = "freerad" group = "freerad" allow_core_dumps = no } name = "freeradius" prefix = "/usr" localstatedir = "/var" logdir = "/var/log/freeradius" run_dir = "/var/run/freeradius" } main { name = "freeradius" prefix = "/usr" localstatedir = "/var" sbindir = "/usr/sbin" logdir = "/var/log/freeradius" run_dir = "/var/run/freeradius" libdir = "/usr/lib/freeradius" radacctdir = "/var/log/freeradius/radacct" hostname_lookups = no max_request_time = 30 cleanup_delay = 5 max_requests = 16384 pidfile = "/var/run/freeradius/freeradius.pid" checkrad = "/usr/sbin/checkrad" debug_level = 0 proxy_requests = yes log { stripped_names = no auth = no auth_badpass = no auth_goodpass = no colourise = yes msg_denied = "You are already logged in - access denied" } resources { } security { max_attributes = 200 reject_delay = 1.000000 status_server = yes } } radiusd: #### Loading Realms and Home Servers #### proxy server { retry_delay = 5 retry_count = 3 default_fallback = no dead_time = 120 wake_all_if_all_dead = no } home_server localhost { ipaddr = 127.0.0.1 port = 1812 type = "auth" secret = <<< secret >>> response_window = 20.000000 response_timeouts = 1 max_outstanding = 65536 zombie_period = 40 status_check = "status-server" ping_interval = 30 check_interval = 30 check_timeout = 4 num_answers_to_alive = 3 revive_interval = 120 limit { max_connections = 16 max_requests = 0 lifetime = 0 idle_timeout = 0 } coa { irt = 2 mrt = 16 mrc = 5 mrd = 30 } } home_server_pool my_auth_failover { type = fail-over home_server = localhost } realm example.com { auth_pool = my_auth_failover } realm LOCAL { } radiusd: #### Loading Clients #### client localhost { ipaddr = 127.0.0.1 require_message_authenticator = no secret = <<< secret >>> nas_type = "other" proto = "*" limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } client localhost_ipv6 { ipv6addr = ::1 require_message_authenticator = no secret = <<< secret >>> limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } Debugger not attached # Creating Auth-Type = mschap # Creating Auth-Type = digest # Creating Auth-Type = eap # Creating Auth-Type = PAP # Creating Auth-Type = CHAP # Creating Auth-Type = MS-CHAP radiusd: #### Instantiating modules #### modules { # Loaded module rlm_eap # Loading module "eap" from file /etc/freeradius/3.0/mods-enabled/eap eap { default_eap_type = "peap" timer_expire = 60 ignore_unknown_eap_types = no cisco_accounting_username_bug = no max_sessions = 16384 } # Loaded module rlm_utf8 # Loading module "utf8" from file /etc/freeradius/3.0/mods-enabled/utf8 # Loaded module rlm_expr # Loading module "expr" from file /etc/freeradius/3.0/mods-enabled/expr expr { safe_characters = "@abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789.-_: /äéöüàâæçèéêëîïôœùûüaÿÄÉÖÜßÀÂÆÇÈÉÊËÎÏÔŒÙÛÜŸ" } # Loaded module rlm_detail # Loading module "detail" from file /etc/freeradius/3.0/mods-enabled/detail detail { filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loaded module rlm_attr_filter # Loading module "attr_filter.post-proxy" from file /etc/freeradius/3.0/mods-enabled/attr_filter attr_filter attr_filter.post-proxy { filename = "/etc/freeradius/3.0/mods-config/attr_filter/post-proxy" key = "%{Realm}" relaxed = no } # Loading module "attr_filter.pre-proxy" from file /etc/freeradius/3.0/mods-enabled/attr_filter attr_filter attr_filter.pre-proxy { filename = "/etc/freeradius/3.0/mods-config/attr_filter/pre-proxy" key = "%{Realm}" relaxed = no } # Loading module "attr_filter.access_reject" from file /etc/freeradius/3.0/mods-enabled/attr_filter attr_filter attr_filter.access_reject { filename = "/etc/freeradius/3.0/mods-config/attr_filter/access_reject" key = "%{User-Name}" relaxed = no } # Loading module "attr_filter.access_challenge" from file /etc/freeradius/3.0/mods-enabled/attr_filter attr_filter attr_filter.access_challenge { filename = "/etc/freeradius/3.0/mods-config/attr_filter/access_challenge" key = "%{User-Name}" relaxed = no } # Loading module "attr_filter.accounting_response" from file /etc/freeradius/3.0/mods-enabled/attr_filter attr_filter attr_filter.accounting_response { filename = "/etc/freeradius/3.0/mods-config/attr_filter/accounting_response" key = "%{User-Name}" relaxed = no } # Loaded module rlm_exec # Loading module "exec" from file /etc/freeradius/3.0/mods-enabled/exec exec { wait = no input_pairs = "request" shell_escape = yes timeout = 10 } # Loaded module rlm_soh # Loading module "soh" from file /etc/freeradius/3.0/mods-enabled/soh soh { dhcp = yes } # Loaded module rlm_dynamic_clients # Loading module "dynamic_clients" from file /etc/freeradius/3.0/mods-enabled/dynamic_clients # Loading module "add_user" from file /etc/freeradius/3.0/mods-enabled/add_user exec add_user { wait = no program = "/usr/bin/python3 /usr/local/add_user.py %{User-Name} %{outer.request:Calling-Station-Id} %{outer.request:EAP-Type} %{&control:Auth-Type}" input_pairs = "request" shell_escape = yes timeout = 1 } # Loaded module rlm_passwd # Loading module "etc_passwd" from file /etc/freeradius/3.0/mods-enabled/passwd passwd etc_passwd { filename = "/etc/passwd" format = "*User-Name:Crypt-Password:" delimiter = ":" ignore_nislike = no ignore_empty = yes allow_multiple_keys = no hash_size = 100 } # Loading module "auth_log" from file /etc/freeradius/3.0/mods-enabled/detail.log detail auth_log { filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loading module "reply_log" from file /etc/freeradius/3.0/mods-enabled/detail.log detail reply_log { filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/reply-detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loading module "pre_proxy_log" from file /etc/freeradius/3.0/mods-enabled/detail.log detail pre_proxy_log { filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/pre-proxy-detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loading module "post_proxy_log" from file /etc/freeradius/3.0/mods-enabled/detail.log detail post_proxy_log { filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/post-proxy-detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loaded module rlm_unpack # Loading module "unpack" from file /etc/freeradius/3.0/mods-enabled/unpack # Loaded module rlm_always # Loading module "reject" from file /etc/freeradius/3.0/mods-enabled/always always reject { rcode = "reject" simulcount = 0 mpp = no } # Loading module "fail" from file /etc/freeradius/3.0/mods-enabled/always always fail { rcode = "fail" simulcount = 0 mpp = no } # Loading module "ok" from file /etc/freeradius/3.0/mods-enabled/always always ok { rcode = "ok" simulcount = 0 mpp = no } # Loading module "handled" from file /etc/freeradius/3.0/mods-enabled/always always handled { rcode = "handled" simulcount = 0 mpp = no } # Loading module "invalid" from file /etc/freeradius/3.0/mods-enabled/always always invalid { rcode = "invalid" simulcount = 0 mpp = no } # Loading module "userlock" from file /etc/freeradius/3.0/mods-enabled/always always userlock { rcode = "userlock" simulcount = 0 mpp = no } # Loading module "notfound" from file /etc/freeradius/3.0/mods-enabled/always always notfound { rcode = "notfound" simulcount = 0 mpp = no } # Loading module "noop" from file /etc/freeradius/3.0/mods-enabled/always always noop { rcode = "noop" simulcount = 0 mpp = no } # Loading module "updated" from file /etc/freeradius/3.0/mods-enabled/always always updated { rcode = "updated" simulcount = 0 mpp = no } # Loaded module rlm_cache # Loading module "cache_eap" from file /etc/freeradius/3.0/mods-enabled/cache_eap cache cache_eap { driver = "rlm_cache_rbtree" key = "%{%{control:State}:-%{%{reply:State}:-%{State}}}" ttl = 15 max_entries = 0 epoch = 0 add_stats = no } # Loaded module rlm_digest # Loading module "digest" from file /etc/freeradius/3.0/mods-enabled/digest # Loaded module rlm_pap # Loading module "pap" from file /etc/freeradius/3.0/mods-enabled/pap pap { normalise = yes } # Loaded module rlm_mschap # Loading module "mschap" from file /etc/freeradius/3.0/mods-enabled/mschap mschap { use_mppe = yes require_encryption = no require_strong = no with_ntdomain_hack = yes passchange { } allow_retry = yes winbind_retry_with_normalised_username = no } # Loading module "ntlm_auth" from file /etc/freeradius/3.0/mods-enabled/ntlm_auth exec ntlm_auth { wait = yes program = "/path/to/ntlm_auth --request-nt-key --domain=MYDOMAIN --username=%{mschap:User-Name} --password=%{User-Password}" shell_escape = yes } # Loaded module rlm_realm # Loading module "IPASS" from file /etc/freeradius/3.0/mods-enabled/realm realm IPASS { format = "prefix" delimiter = "/" ignore_default = no ignore_null = no } # Loading module "suffix" from file /etc/freeradius/3.0/mods-enabled/realm realm suffix { format = "suffix" delimiter = "@" ignore_default = no ignore_null = no } # Loading module "realmpercent" from file /etc/freeradius/3.0/mods-enabled/realm realm realmpercent { format = "suffix" delimiter = "%" ignore_default = no ignore_null = no } # Loading module "ntdomain" from file /etc/freeradius/3.0/mods-enabled/realm realm ntdomain { format = "prefix" delimiter = "\\" ignore_default = no ignore_null = no } # Loaded module rlm_logintime # Loading module "logintime" from file /etc/freeradius/3.0/mods-enabled/logintime logintime { minimum_timeout = 60 } # Loaded module rlm_linelog # Loading module "linelog" from file /etc/freeradius/3.0/mods-enabled/linelog linelog { filename = "/var/log/freeradius/linelog" escape_filenames = no syslog_severity = "info" permissions = 384 format = "This is a log message for %{User-Name}" reference = "messages.%{%{reply:Packet-Type}:-default}" } # Loading module "log_accounting" from file /etc/freeradius/3.0/mods-enabled/linelog linelog log_accounting { filename = "/var/log/freeradius/linelog-accounting" escape_filenames = no syslog_severity = "info" permissions = 384 format = "" reference = "Accounting-Request.%{%{Acct-Status-Type}:-unknown}" } # Loaded module rlm_expiration # Loading module "expiration" from file /etc/freeradius/3.0/mods-enabled/expiration # Loaded module rlm_chap # Loading module "chap" from file /etc/freeradius/3.0/mods-enabled/chap # Loaded module rlm_files # Loading module "files" from file /etc/freeradius/3.0/mods-enabled/files files { filename = "/etc/freeradius/3.0/mods-config/files/authorize" acctusersfile = "/etc/freeradius/3.0/mods-config/files/accounting" preproxy_usersfile = "/etc/freeradius/3.0/mods-config/files/pre-proxy" } # Loaded module rlm_replicate # Loading module "replicate" from file /etc/freeradius/3.0/mods-enabled/replicate # Loading module "add_user_pap" from file /etc/freeradius/3.0/mods-enabled/add_user_pap exec add_user_pap { wait = no program = "/usr/bin/python3 /usr/local/add_user_pap.py %{User-Name} %{User-Password} %{outer.request:Calling-Station-Id}" input_pairs = "request" shell_escape = yes timeout = 1 } # Loaded module rlm_radutmp # Loading module "radutmp" from file /etc/freeradius/3.0/mods-enabled/radutmp radutmp { filename = "/var/log/freeradius/radutmp" username = "%{User-Name}" case_sensitive = yes check_with_nas = yes permissions = 384 caller_id = yes } # Loaded module rlm_unix # Loading module "unix" from file /etc/freeradius/3.0/mods-enabled/unix unix { radwtmp = "/var/log/freeradius/radwtmp" } Creating attribute Unix-Group # Loading module "echo" from file /etc/freeradius/3.0/mods-enabled/echo exec echo { wait = yes program = "/bin/echo %{User-Name}" input_pairs = "request" output_pairs = "reply" shell_escape = yes } # Loaded module rlm_preprocess # Loading module "preprocess" from file /etc/freeradius/3.0/mods-enabled/preprocess preprocess { huntgroups = "/etc/freeradius/3.0/mods-config/preprocess/huntgroups" hints = "/etc/freeradius/3.0/mods-config/preprocess/hints" with_ascend_hack = no ascend_channels_per_line = 23 with_ntdomain_hack = no with_specialix_jetstream_hack = no with_cisco_vsa_hack = no with_alvarion_vsa_hack = no } # Loading module "sradutmp" from file /etc/freeradius/3.0/mods-enabled/sradutmp radutmp sradutmp { filename = "/var/log/freeradius/sradutmp" username = "%{User-Name}" case_sensitive = yes check_with_nas = yes permissions = 420 caller_id = no } instantiate { } # Instantiating module "eap" from file /etc/freeradius/3.0/mods-enabled/eap # Linked to sub-module rlm_eap_md5 # Linked to sub-module rlm_eap_leap # Linked to sub-module rlm_eap_gtc gtc { challenge = "Password: " auth_type = "PAP" } # Linked to sub-module rlm_eap_tls tls { tls = "tls-common" } tls-config tls-common { verify_depth = 0 ca_path = "/etc/freeradius/3.0/certs" pem_file_type = yes private_key_file = "/etc/freeradius/3.0/certs/server.key" certificate_file = "/etc/freeradius/3.0/certs/server.pem" ca_file = "/etc/freeradius/3.0/certs/ca.pem" private_key_password = <<< secret >>> dh_file = "/etc/freeradius/3.0/certs/dh" random_file = "/dev/urandom" fragment_size = 1024 include_length = yes auto_chain = yes check_crl = no check_all_crl = no cipher_list = "DEFAULT" cipher_server_preference = no ecdh_curve = "prime256v1" tls_max_version = "" tls_min_version = "1.0" cache { enable = no lifetime = 24 max_entries = 255 } verify { skip_if_ocsp_ok = no } ocsp { enable = no override_cert_url = yes url = "http://127.0.0.1/ocsp/" use_nonce = yes timeout = 0 softfail = no } } # Linked to sub-module rlm_eap_ttls ttls { tls = "tls-common" default_eap_type = "mschapv2" copy_request_to_tunnel = yes use_tunneled_reply = yes virtual_server = "inner-tunnel" include_length = yes require_client_cert = no } tls: Using cached TLS configuration from previous invocation # Linked to sub-module rlm_eap_peap peap { tls = "tls-common" default_eap_type = "mschapv2" copy_request_to_tunnel = yes use_tunneled_reply = yes proxy_tunneled_request_as_eap = no virtual_server = "inner-tunnel" soh = no require_client_cert = no } tls: Using cached TLS configuration from previous invocation # Linked to sub-module rlm_eap_mschapv2 mschapv2 { with_ntdomain_hack = no send_error = no } # Instantiating module "detail" from file /etc/freeradius/3.0/mods-enabled/detail # Instantiating module "attr_filter.post-proxy" from file /etc/freeradius/3.0/mods-enabled/attr_filter reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/post-proxy # Instantiating module "attr_filter.pre-proxy" from file /etc/freeradius/3.0/mods-enabled/attr_filter reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/pre-proxy # Instantiating module "attr_filter.access_reject" from file /etc/freeradius/3.0/mods-enabled/attr_filter reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/access_reject [/etc/freeradius/3.0/mods-config/attr_filter/access_reject]:11 Check item "FreeRADIUS-Response-Delay" found in filter list for realm "DEFAULT". [/etc/freeradius/3.0/mods-config/attr_filter/access_reject]:11 Check item "FreeRADIUS-Response-Delay-USec" found in filter list for realm "DEFAULT". # Instantiating module "attr_filter.access_challenge" from file /etc/freeradius/3.0/mods-enabled/attr_filter reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/access_challenge # Instantiating module "attr_filter.accounting_response" from file /etc/freeradius/3.0/mods-enabled/attr_filter reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/accounting_response # Instantiating module "etc_passwd" from file /etc/freeradius/3.0/mods-enabled/passwd rlm_passwd: nfields: 3 keyfield 0(User-Name) listable: no # Instantiating module "auth_log" from file /etc/freeradius/3.0/mods-enabled/detail.log rlm_detail (auth_log): 'User-Password' suppressed, will not appear in detail output # Instantiating module "reply_log" from file /etc/freeradius/3.0/mods-enabled/detail.log # Instantiating module "pre_proxy_log" from file /etc/freeradius/3.0/mods-enabled/detail.log # Instantiating module "post_proxy_log" from file /etc/freeradius/3.0/mods-enabled/detail.log # Instantiating module "reject" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "fail" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "ok" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "handled" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "invalid" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "userlock" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "notfound" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "noop" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "updated" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "cache_eap" from file /etc/freeradius/3.0/mods-enabled/cache_eap rlm_cache (cache_eap): Driver rlm_cache_rbtree (module rlm_cache_rbtree) loaded and linked # Instantiating module "pap" from file /etc/freeradius/3.0/mods-enabled/pap # Instantiating module "mschap" from file /etc/freeradius/3.0/mods-enabled/mschap rlm_mschap (mschap): using internal authentication # Instantiating module "IPASS" from file /etc/freeradius/3.0/mods-enabled/realm # Instantiating module "suffix" from file /etc/freeradius/3.0/mods-enabled/realm # Instantiating module "realmpercent" from file /etc/freeradius/3.0/mods-enabled/realm # Instantiating module "ntdomain" from file /etc/freeradius/3.0/mods-enabled/realm # Instantiating module "logintime" from file /etc/freeradius/3.0/mods-enabled/logintime # Instantiating module "linelog" from file /etc/freeradius/3.0/mods-enabled/linelog # Instantiating module "log_accounting" from file /etc/freeradius/3.0/mods-enabled/linelog # Instantiating module "expiration" from file /etc/freeradius/3.0/mods-enabled/expiration # Instantiating module "files" from file /etc/freeradius/3.0/mods-enabled/files reading pairlist file /etc/freeradius/3.0/mods-config/files/authorize reading pairlist file /etc/freeradius/3.0/mods-config/files/accounting reading pairlist file /etc/freeradius/3.0/mods-config/files/pre-proxy # Instantiating module "preprocess" from file /etc/freeradius/3.0/mods-enabled/preprocess reading pairlist file /etc/freeradius/3.0/mods-config/preprocess/huntgroups reading pairlist file /etc/freeradius/3.0/mods-config/preprocess/hints } # modules radiusd: #### Loading Virtual Servers #### server { # from file /etc/freeradius/3.0/radiusd.conf } # server server default { # from file /etc/freeradius/3.0/sites-enabled/default # Loading authenticate {...} # Loading authorize {...} Ignoring "sql" (see raddb/mods-available/README.rst) Ignoring "ldap" (see raddb/mods-available/README.rst) # Loading preacct {...} # Loading accounting {...} # Loading post-proxy {...} # Loading post-auth {...} } # server default server inner-tunnel { # from file /etc/freeradius/3.0/sites-enabled/inner-tunnel # Loading authenticate {...} # Loading authorize {...} # Loading session {...} # Loading post-proxy {...} # Loading post-auth {...} # Skipping contents of 'if' as it is always 'false' -- /etc/freeradius/3.0/sites-enabled/inner-tunnel:344 } # server inner-tunnel radiusd: #### Opening IP addresses and Ports #### listen { type = "auth" ipaddr = * port = 0 limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } listen { type = "acct" ipaddr = * port = 0 limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } listen { type = "auth" ipv6addr = :: port = 0 limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } listen { type = "acct" ipv6addr = :: port = 0 limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } listen { type = "auth" ipaddr = 127.0.0.1 port = 18120 } Listening on auth address * port 1812 bound to server default Listening on acct address * port 1813 bound to server default Listening on auth address :: port 1812 bound to server default Listening on acct address :: port 1813 bound to server default Listening on auth address 127.0.0.1 port 18120 bound to server inner-tunnel Listening on proxy address * port 55244 Listening on proxy address :: port 49183 Ready to process requests (0) Received Access-Request Id 120 from 127.0.0.1:46839 to 127.0.0.1:1812 length 211 (0) User-Name = "GalaxyS4" (0) NAS-IP-Address = 127.0.0.1 (0) Called-Station-Id = "98-48-27-C7-D3-CF:eduroam" (0) NAS-Port-Type = Wireless-802.11 (0) Service-Type = Framed-User (0) Calling-Station-Id = "CC-3A-61-98-18-B5" (0) Connect-Info = "CONNECT 11Mbps 802.11g" (0) Acct-Session-Id = "09E72C4CDC778796" (0) Acct-Multi-Session-Id = "E0705DD1DE6F9FEF" (0) WLAN-Pairwise-Cipher = 1027076 (0) WLAN-Group-Cipher = 1027076 (0) WLAN-AKM-Suite = 1027073 (0) Framed-MTU = 1400 (0) EAP-Message = 0x022e000d0147616c6178795334 (0) Message-Authenticator = 0x7aaba9eee275f0464fab2c30ccc068e9 (0) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (0) authorize { (0) policy filter_username { (0) if (&User-Name) { (0) if (&User-Name) -> TRUE (0) if (&User-Name) { (0) if (&User-Name =~ / /) { (0) if (&User-Name =~ / /) -> FALSE (0) if (&User-Name =~ /@[^@]*@/ ) { (0) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (0) if (&User-Name =~ /\.\./ ) { (0) if (&User-Name =~ /\.\./ ) -> FALSE (0) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) { (0) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE (0) if (&User-Name =~ /\.$/) { (0) if (&User-Name =~ /\.$/) -> FALSE (0) if (&User-Name =~ /@\./) { (0) if (&User-Name =~ /@\./) -> FALSE (0) } # if (&User-Name) = notfound (0) } # policy filter_username = notfound (0) [preprocess] = ok (0) [chap] = noop (0) [mschap] = noop (0) [digest] = noop (0) suffix: Checking for suffix after "@" (0) suffix: No '@' in User-Name = "GalaxyS4", looking up realm NULL (0) suffix: No such realm "NULL" (0) [suffix] = noop (0) eap: Peer sent EAP Response (code 2) ID 46 length 13 (0) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize (0) [eap] = ok (0) } # authorize = ok (0) Found Auth-Type = eap (0) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (0) authenticate { (0) eap: Peer sent packet with method EAP Identity (1) (0) eap: Calling submodule eap_peap to process data (0) eap_peap: Initiating new EAP-TLS session (0) eap_peap: [eaptls start] = request (0) eap: Sending EAP Request (code 1) ID 47 length 6 (0) eap: EAP session adding &reply:State = 0xf1d1cadff1fed394 (0) [eap] = handled (0) } # authenticate = handled (0) Using Post-Auth-Type Challenge (0) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (0) Challenge { ... } # empty sub-section is ignored (0) Sent Access-Challenge Id 120 from 127.0.0.1:1812 to 127.0.0.1:46839 length 0 (0) EAP-Message = 0x012f00061920 (0) Message-Authenticator = 0x00000000000000000000000000000000 (0) State = 0xf1d1cadff1fed394ae57fe37bedc2af7 (0) Finished request Waking up in 4.9 seconds. (1) Received Access-Request Id 121 from 127.0.0.1:46839 to 127.0.0.1:1812 length 384 (1) User-Name = "GalaxyS4" (1) NAS-IP-Address = 127.0.0.1 (1) Called-Station-Id = "98-48-27-C7-D3-CF:eduroam" (1) NAS-Port-Type = Wireless-802.11 (1) Service-Type = Framed-User (1) Calling-Station-Id = "CC-3A-61-98-18-B5" (1) Connect-Info = "CONNECT 11Mbps 802.11g" (1) Acct-Session-Id = "09E72C4CDC778796" (1) Acct-Multi-Session-Id = "E0705DD1DE6F9FEF" (1) WLAN-Pairwise-Cipher = 1027076 (1) WLAN-Group-Cipher = 1027076 (1) WLAN-AKM-Suite = 1027073 (1) Framed-MTU = 1400 (1) EAP-Message = 0x022f00a819800000009e1603010099010000950303b852f07dd0922a13737811ae1391e9b73d73c8c8418574d27029364723203be100003cc02cc030009fc02bc02f009ec00ac024c014c0280039006bc009c023c013c02700330067c007c011009d009c0035003d002f003c00050004000a00ff010000 (1) State = 0xf1d1cadff1fed394ae57fe37bedc2af7 (1) Message-Authenticator = 0xa7d200bc9585674e1236f4f744bc6bf0 (1) session-state: No cached attributes (1) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (1) authorize { (1) policy filter_username { (1) if (&User-Name) { (1) if (&User-Name) -> TRUE (1) if (&User-Name) { (1) if (&User-Name =~ / /) { (1) if (&User-Name =~ / /) -> FALSE (1) if (&User-Name =~ /@[^@]*@/ ) { (1) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (1) if (&User-Name =~ /\.\./ ) { (1) if (&User-Name =~ /\.\./ ) -> FALSE (1) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) { (1) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE (1) if (&User-Name =~ /\.$/) { (1) if (&User-Name =~ /\.$/) -> FALSE (1) if (&User-Name =~ /@\./) { (1) if (&User-Name =~ /@\./) -> FALSE (1) } # if (&User-Name) = notfound (1) } # policy filter_username = notfound (1) [preprocess] = ok (1) [chap] = noop (1) [mschap] = noop (1) [digest] = noop (1) suffix: Checking for suffix after "@" (1) suffix: No '@' in User-Name = "GalaxyS4", looking up realm NULL (1) suffix: No such realm "NULL" (1) [suffix] = noop (1) eap: Peer sent EAP Response (code 2) ID 47 length 168 (1) eap: Continuing tunnel setup (1) [eap] = ok (1) } # authorize = ok (1) Found Auth-Type = eap (1) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (1) authenticate { (1) eap: Expiring EAP session with state 0xf1d1cadff1fed394 (1) eap: Finished EAP session with state 0xf1d1cadff1fed394 (1) eap: Previous EAP request found for state 0xf1d1cadff1fed394, released from the list (1) eap: Peer sent packet with method EAP PEAP (25) (1) eap: Calling submodule eap_peap to process data (1) eap_peap: Continuing EAP-TLS (1) eap_peap: Peer indicated complete TLS record size will be 158 bytes (1) eap_peap: Got complete TLS record (158 bytes) (1) eap_peap: [eaptls verify] = length included (1) eap_peap: (other): before SSL initialization (1) eap_peap: TLS_accept: before SSL initialization (1) eap_peap: TLS_accept: before SSL initialization (1) eap_peap: <<< recv UNKNOWN TLS VERSION ?0304? [length 0099] (1) eap_peap: TLS_accept: SSLv3/TLS read client hello (1) eap_peap: >>> send TLS 1.2 [length 003d] (1) eap_peap: TLS_accept: SSLv3/TLS write server hello (1) eap_peap: >>> send TLS 1.2 [length 0953] (1) eap_peap: TLS_accept: SSLv3/TLS write certificate (1) eap_peap: >>> send TLS 1.2 [length 014d] (1) eap_peap: TLS_accept: SSLv3/TLS write key exchange (1) eap_peap: >>> send TLS 1.2 [length 0004] (1) eap_peap: TLS_accept: SSLv3/TLS write server done (1) eap_peap: TLS_accept: Need to read more data: SSLv3/TLS write server done (1) eap_peap: In SSL Handshake Phase (1) eap_peap: In SSL Accept mode (1) eap_peap: [eaptls process] = handled (1) eap: Sending EAP Request (code 1) ID 48 length 1004 (1) eap: EAP session adding &reply:State = 0xf1d1cadff0e1d394 (1) [eap] = handled (1) } # authenticate = handled (1) Using Post-Auth-Type Challenge (1) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (1) Challenge { ... } # empty sub-section is ignored (1) Sent Access-Challenge Id 121 from 127.0.0.1:1812 to 127.0.0.1:46839 length 0 (1) EAP-Message = 0x013003ec19c000000af5160303003d0200003903034c6b31ad1308ed121b66e56a1c643d659c197136bc1bf600444f574e4752440100c030000011ff01000100000b0004030001020017000016030309530b00094f00094c00041930820415308202fda003020102020101300d06092a864886f70d0101 (1) Message-Authenticator = 0x00000000000000000000000000000000 (1) State = 0xf1d1cadff0e1d394ae57fe37bedc2af7 (1) Finished request Waking up in 4.9 seconds. (2) Received Access-Request Id 122 from 127.0.0.1:46839 to 127.0.0.1:1812 length 222 (2) User-Name = "GalaxyS4" (2) NAS-IP-Address = 127.0.0.1 (2) Called-Station-Id = "98-48-27-C7-D3-CF:eduroam" (2) NAS-Port-Type = Wireless-802.11 (2) Service-Type = Framed-User (2) Calling-Station-Id = "CC-3A-61-98-18-B5" (2) Connect-Info = "CONNECT 11Mbps 802.11g" (2) Acct-Session-Id = "09E72C4CDC778796" (2) Acct-Multi-Session-Id = "E0705DD1DE6F9FEF" (2) WLAN-Pairwise-Cipher = 1027076 (2) WLAN-Group-Cipher = 1027076 (2) WLAN-AKM-Suite = 1027073 (2) Framed-MTU = 1400 (2) EAP-Message = 0x023000061900 (2) State = 0xf1d1cadff0e1d394ae57fe37bedc2af7 (2) Message-Authenticator = 0xd84be54680f0318614d37ab88a74e399 (2) session-state: No cached attributes (2) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (2) authorize { (2) policy filter_username { (2) if (&User-Name) { (2) if (&User-Name) -> TRUE (2) if (&User-Name) { (2) if (&User-Name =~ / /) { (2) if (&User-Name =~ / /) -> FALSE (2) if (&User-Name =~ /@[^@]*@/ ) { (2) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (2) if (&User-Name =~ /\.\./ ) { (2) if (&User-Name =~ /\.\./ ) -> FALSE (2) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) { (2) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE (2) if (&User-Name =~ /\.$/) { (2) if (&User-Name =~ /\.$/) -> FALSE (2) if (&User-Name =~ /@\./) { (2) if (&User-Name =~ /@\./) -> FALSE (2) } # if (&User-Name) = notfound (2) } # policy filter_username = notfound (2) [preprocess] = ok (2) [chap] = noop (2) [mschap] = noop (2) [digest] = noop (2) suffix: Checking for suffix after "@" (2) suffix: No '@' in User-Name = "GalaxyS4", looking up realm NULL (2) suffix: No such realm "NULL" (2) [suffix] = noop (2) eap: Peer sent EAP Response (code 2) ID 48 length 6 (2) eap: Continuing tunnel setup (2) [eap] = ok (2) } # authorize = ok (2) Found Auth-Type = eap (2) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (2) authenticate { (2) eap: Expiring EAP session with state 0xf1d1cadff0e1d394 (2) eap: Finished EAP session with state 0xf1d1cadff0e1d394 (2) eap: Previous EAP request found for state 0xf1d1cadff0e1d394, released from the list (2) eap: Peer sent packet with method EAP PEAP (25) (2) eap: Calling submodule eap_peap to process data (2) eap_peap: Continuing EAP-TLS (2) eap_peap: Peer ACKed our handshake fragment (2) eap_peap: [eaptls verify] = request (2) eap_peap: [eaptls process] = handled (2) eap: Sending EAP Request (code 1) ID 49 length 1000 (2) eap: EAP session adding &reply:State = 0xf1d1cadff3e0d394 (2) [eap] = handled (2) } # authenticate = handled (2) Using Post-Auth-Type Challenge (2) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (2) Challenge { ... } # empty sub-section is ignored (2) Sent Access-Challenge Id 122 from 127.0.0.1:1812 to 127.0.0.1:46839 length 0 (2) EAP-Message = 0x013103e81940a97c446585ebe1d4435a82267edecc13e1d7302b291588b848d40d4d414e4fcab0b868bc110fe2862b2023554cecd6920123a2809dfaa2d105e5f29e53af2c0a317751ff4baeaa9a02fcf65405a66cfaf86fe601e9eeccddf1cba618a2b16d2bea3531f48bcdd6edb58c683a0b7b254fa7 (2) Message-Authenticator = 0x00000000000000000000000000000000 (2) State = 0xf1d1cadff3e0d394ae57fe37bedc2af7 (2) Finished request Waking up in 4.9 seconds. (3) Received Access-Request Id 123 from 127.0.0.1:46839 to 127.0.0.1:1812 length 222 (3) User-Name = "GalaxyS4" (3) NAS-IP-Address = 127.0.0.1 (3) Called-Station-Id = "98-48-27-C7-D3-CF:eduroam" (3) NAS-Port-Type = Wireless-802.11 (3) Service-Type = Framed-User (3) Calling-Station-Id = "CC-3A-61-98-18-B5" (3) Connect-Info = "CONNECT 11Mbps 802.11g" (3) Acct-Session-Id = "09E72C4CDC778796" (3) Acct-Multi-Session-Id = "E0705DD1DE6F9FEF" (3) WLAN-Pairwise-Cipher = 1027076 (3) WLAN-Group-Cipher = 1027076 (3) WLAN-AKM-Suite = 1027073 (3) Framed-MTU = 1400 (3) EAP-Message = 0x023100061900 (3) State = 0xf1d1cadff3e0d394ae57fe37bedc2af7 (3) Message-Authenticator = 0x08798dad5a4c17a35a81ba3efe3e2572 (3) session-state: No cached attributes (3) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (3) authorize { (3) policy filter_username { (3) if (&User-Name) { (3) if (&User-Name) -> TRUE (3) if (&User-Name) { (3) if (&User-Name =~ / /) { (3) if (&User-Name =~ / /) -> FALSE (3) if (&User-Name =~ /@[^@]*@/ ) { (3) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (3) if (&User-Name =~ /\.\./ ) { (3) if (&User-Name =~ /\.\./ ) -> FALSE (3) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) { (3) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE (3) if (&User-Name =~ /\.$/) { (3) if (&User-Name =~ /\.$/) -> FALSE (3) if (&User-Name =~ /@\./) { (3) if (&User-Name =~ /@\./) -> FALSE (3) } # if (&User-Name) = notfound (3) } # policy filter_username = notfound (3) [preprocess] = ok (3) [chap] = noop (3) [mschap] = noop (3) [digest] = noop (3) suffix: Checking for suffix after "@" (3) suffix: No '@' in User-Name = "GalaxyS4", looking up realm NULL (3) suffix: No such realm "NULL" (3) [suffix] = noop (3) eap: Peer sent EAP Response (code 2) ID 49 length 6 (3) eap: Continuing tunnel setup (3) [eap] = ok (3) } # authorize = ok (3) Found Auth-Type = eap (3) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (3) authenticate { (3) eap: Expiring EAP session with state 0xf1d1cadff3e0d394 (3) eap: Finished EAP session with state 0xf1d1cadff3e0d394 (3) eap: Previous EAP request found for state 0xf1d1cadff3e0d394, released from the list (3) eap: Peer sent packet with method EAP PEAP (25) (3) eap: Calling submodule eap_peap to process data (3) eap_peap: Continuing EAP-TLS (3) eap_peap: Peer ACKed our handshake fragment (3) eap_peap: [eaptls verify] = request (3) eap_peap: [eaptls process] = handled (3) eap: Sending EAP Request (code 1) ID 50 length 823 (3) eap: EAP session adding &reply:State = 0xf1d1cadff2e3d394 (3) [eap] = handled (3) } # authenticate = handled (3) Using Post-Auth-Type Challenge (3) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (3) Challenge { ... } # empty sub-section is ignored (3) Sent Access-Challenge Id 123 from 127.0.0.1:1812 to 127.0.0.1:46839 length 0 (3) EAP-Message = 0x0132033719006976657273697461206465676c692053747564692064692042726573636961202d20552e4f2e432e205265746920652053697374656d693122302006092a864886f70d0109011613686f73746d617374657240756e6962732e69743111300f06035504030c08756e6962732e6974820900 (3) Message-Authenticator = 0x00000000000000000000000000000000 (3) State = 0xf1d1cadff2e3d394ae57fe37bedc2af7 (3) Finished request Waking up in 4.9 seconds. (4) Received Access-Request Id 124 from 127.0.0.1:46839 to 127.0.0.1:1812 length 352 (4) User-Name = "GalaxyS4" (4) NAS-IP-Address = 127.0.0.1 (4) Called-Station-Id = "98-48-27-C7-D3-CF:eduroam" (4) NAS-Port-Type = Wireless-802.11 (4) Service-Type = Framed-User (4) Calling-Station-Id = "CC-3A-61-98-18-B5" (4) Connect-Info = "CONNECT 11Mbps 802.11g" (4) Acct-Session-Id = "09E72C4CDC778796" (4) Acct-Multi-Session-Id = "E0705DD1DE6F9FEF" (4) WLAN-Pairwise-Cipher = 1027076 (4) WLAN-Group-Cipher = 1027076 (4) WLAN-AKM-Suite = 1027073 (4) Framed-MTU = 1400 (4) EAP-Message = 0x0232008819800000007e1603030046100000424104162861bf684570d5aa1139a59bf9f87633d00aac51b5add196157e95608a8af09bec9fa25144a432aad462a03f62c4642334fd5ed0af3a3000416e22f31b780f14030300010116030300280000000000000000c5584650b0bd5edb9a4723cc311969 (4) State = 0xf1d1cadff2e3d394ae57fe37bedc2af7 (4) Message-Authenticator = 0xbe40379c3514e40d13442693c5e72fd0 (4) session-state: No cached attributes (4) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (4) authorize { (4) policy filter_username { (4) if (&User-Name) { (4) if (&User-Name) -> TRUE (4) if (&User-Name) { (4) if (&User-Name =~ / /) { (4) if (&User-Name =~ / /) -> FALSE (4) if (&User-Name =~ /@[^@]*@/ ) { (4) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (4) if (&User-Name =~ /\.\./ ) { (4) if (&User-Name =~ /\.\./ ) -> FALSE (4) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) { (4) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE (4) if (&User-Name =~ /\.$/) { (4) if (&User-Name =~ /\.$/) -> FALSE (4) if (&User-Name =~ /@\./) { (4) if (&User-Name =~ /@\./) -> FALSE (4) } # if (&User-Name) = notfound (4) } # policy filter_username = notfound (4) [preprocess] = ok (4) [chap] = noop (4) [mschap] = noop (4) [digest] = noop (4) suffix: Checking for suffix after "@" (4) suffix: No '@' in User-Name = "GalaxyS4", looking up realm NULL (4) suffix: No such realm "NULL" (4) [suffix] = noop (4) eap: Peer sent EAP Response (code 2) ID 50 length 136 (4) eap: Continuing tunnel setup (4) [eap] = ok (4) } # authorize = ok (4) Found Auth-Type = eap (4) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (4) authenticate { (4) eap: Expiring EAP session with state 0xf1d1cadff2e3d394 (4) eap: Finished EAP session with state 0xf1d1cadff2e3d394 (4) eap: Previous EAP request found for state 0xf1d1cadff2e3d394, released from the list (4) eap: Peer sent packet with method EAP PEAP (25) (4) eap: Calling submodule eap_peap to process data (4) eap_peap: Continuing EAP-TLS (4) eap_peap: Peer indicated complete TLS record size will be 126 bytes (4) eap_peap: Got complete TLS record (126 bytes) (4) eap_peap: [eaptls verify] = length included (4) eap_peap: TLS_accept: SSLv3/TLS write server done (4) eap_peap: <<< recv TLS 1.2 [length 0046] (4) eap_peap: TLS_accept: SSLv3/TLS read client key exchange (4) eap_peap: TLS_accept: SSLv3/TLS read change cipher spec (4) eap_peap: <<< recv TLS 1.2 [length 0010] (4) eap_peap: TLS_accept: SSLv3/TLS read finished (4) eap_peap: >>> send TLS 1.2 [length 0001] (4) eap_peap: TLS_accept: SSLv3/TLS write change cipher spec (4) eap_peap: >>> send TLS 1.2 [length 0010] (4) eap_peap: TLS_accept: SSLv3/TLS write finished (4) eap_peap: (other): SSL negotiation finished successfully (4) eap_peap: SSL Connection Established (4) eap_peap: [eaptls process] = handled (4) eap: Sending EAP Request (code 1) ID 51 length 57 (4) eap: EAP session adding &reply:State = 0xf1d1cadff5e2d394 (4) [eap] = handled (4) } # authenticate = handled (4) Using Post-Auth-Type Challenge (4) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (4) Challenge { ... } # empty sub-section is ignored (4) Sent Access-Challenge Id 124 from 127.0.0.1:1812 to 127.0.0.1:46839 length 0 (4) EAP-Message = 0x013300391900140303000101160303002881d0ed97f89fd2f2812ee124f794a3df5843695ccbf562c7a47b548bd369e5bfa87e0afbf18e4b85 (4) Message-Authenticator = 0x00000000000000000000000000000000 (4) State = 0xf1d1cadff5e2d394ae57fe37bedc2af7 (4) Finished request Waking up in 4.8 seconds. (5) Received Access-Request Id 125 from 127.0.0.1:46839 to 127.0.0.1:1812 length 222 (5) User-Name = "GalaxyS4" (5) NAS-IP-Address = 127.0.0.1 (5) Called-Station-Id = "98-48-27-C7-D3-CF:eduroam" (5) NAS-Port-Type = Wireless-802.11 (5) Service-Type = Framed-User (5) Calling-Station-Id = "CC-3A-61-98-18-B5" (5) Connect-Info = "CONNECT 11Mbps 802.11g" (5) Acct-Session-Id = "09E72C4CDC778796" (5) Acct-Multi-Session-Id = "E0705DD1DE6F9FEF" (5) WLAN-Pairwise-Cipher = 1027076 (5) WLAN-Group-Cipher = 1027076 (5) WLAN-AKM-Suite = 1027073 (5) Framed-MTU = 1400 (5) EAP-Message = 0x023300061900 (5) State = 0xf1d1cadff5e2d394ae57fe37bedc2af7 (5) Message-Authenticator = 0xb74e34f967e3c44e7b02eaf018171408 (5) session-state: No cached attributes (5) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (5) authorize { (5) policy filter_username { (5) if (&User-Name) { (5) if (&User-Name) -> TRUE (5) if (&User-Name) { (5) if (&User-Name =~ / /) { (5) if (&User-Name =~ / /) -> FALSE (5) if (&User-Name =~ /@[^@]*@/ ) { (5) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (5) if (&User-Name =~ /\.\./ ) { (5) if (&User-Name =~ /\.\./ ) -> FALSE (5) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) { (5) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE (5) if (&User-Name =~ /\.$/) { (5) if (&User-Name =~ /\.$/) -> FALSE (5) if (&User-Name =~ /@\./) { (5) if (&User-Name =~ /@\./) -> FALSE (5) } # if (&User-Name) = notfound (5) } # policy filter_username = notfound (5) [preprocess] = ok (5) [chap] = noop (5) [mschap] = noop (5) [digest] = noop (5) suffix: Checking for suffix after "@" (5) suffix: No '@' in User-Name = "GalaxyS4", looking up realm NULL (5) suffix: No such realm "NULL" (5) [suffix] = noop (5) eap: Peer sent EAP Response (code 2) ID 51 length 6 (5) eap: Continuing tunnel setup (5) [eap] = ok (5) } # authorize = ok (5) Found Auth-Type = eap (5) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (5) authenticate { (5) eap: Expiring EAP session with state 0xf1d1cadff5e2d394 (5) eap: Finished EAP session with state 0xf1d1cadff5e2d394 (5) eap: Previous EAP request found for state 0xf1d1cadff5e2d394, released from the list (5) eap: Peer sent packet with method EAP PEAP (25) (5) eap: Calling submodule eap_peap to process data (5) eap_peap: Continuing EAP-TLS (5) eap_peap: Peer ACKed our handshake fragment. handshake is finished (5) eap_peap: [eaptls verify] = success (5) eap_peap: [eaptls process] = success (5) eap_peap: Session established. Decoding tunneled attributes (5) eap_peap: PEAP state TUNNEL ESTABLISHED (5) eap: Sending EAP Request (code 1) ID 52 length 40 (5) eap: EAP session adding &reply:State = 0xf1d1cadff4e5d394 (5) [eap] = handled (5) } # authenticate = handled (5) Using Post-Auth-Type Challenge (5) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (5) Challenge { ... } # empty sub-section is ignored (5) Sent Access-Challenge Id 125 from 127.0.0.1:1812 to 127.0.0.1:46839 length 0 (5) EAP-Message = 0x013400281900170303001d81d0ed97f89fd2f35976e559b14c5911d8d2d9949749aa0d0fd60690f3 (5) Message-Authenticator = 0x00000000000000000000000000000000 (5) State = 0xf1d1cadff4e5d394ae57fe37bedc2af7 (5) Finished request Waking up in 4.8 seconds. (6) Received Access-Request Id 126 from 127.0.0.1:46839 to 127.0.0.1:1812 length 260 (6) User-Name = "GalaxyS4" (6) NAS-IP-Address = 127.0.0.1 (6) Called-Station-Id = "98-48-27-C7-D3-CF:eduroam" (6) NAS-Port-Type = Wireless-802.11 (6) Service-Type = Framed-User (6) Calling-Station-Id = "CC-3A-61-98-18-B5" (6) Connect-Info = "CONNECT 11Mbps 802.11g" (6) Acct-Session-Id = "09E72C4CDC778796" (6) Acct-Multi-Session-Id = "E0705DD1DE6F9FEF" (6) WLAN-Pairwise-Cipher = 1027076 (6) WLAN-Group-Cipher = 1027076 (6) WLAN-AKM-Suite = 1027073 (6) Framed-MTU = 1400 (6) EAP-Message = 0x0234002c19001703030021000000000000000133297eabb2643a0e7cb8ab60326cd80dc31e354a107d5265ac (6) State = 0xf1d1cadff4e5d394ae57fe37bedc2af7 (6) Message-Authenticator = 0x858e647c453500902daae45e3a5df69f (6) session-state: No cached attributes (6) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (6) authorize { (6) policy filter_username { (6) if (&User-Name) { (6) if (&User-Name) -> TRUE (6) if (&User-Name) { (6) if (&User-Name =~ / /) { (6) if (&User-Name =~ / /) -> FALSE (6) if (&User-Name =~ /@[^@]*@/ ) { (6) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (6) if (&User-Name =~ /\.\./ ) { (6) if (&User-Name =~ /\.\./ ) -> FALSE (6) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) { (6) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE (6) if (&User-Name =~ /\.$/) { (6) if (&User-Name =~ /\.$/) -> FALSE (6) if (&User-Name =~ /@\./) { (6) if (&User-Name =~ /@\./) -> FALSE (6) } # if (&User-Name) = notfound (6) } # policy filter_username = notfound (6) [preprocess] = ok (6) [chap] = noop (6) [mschap] = noop (6) [digest] = noop (6) suffix: Checking for suffix after "@" (6) suffix: No '@' in User-Name = "GalaxyS4", looking up realm NULL (6) suffix: No such realm "NULL" (6) [suffix] = noop (6) eap: Peer sent EAP Response (code 2) ID 52 length 44 (6) eap: Continuing tunnel setup (6) [eap] = ok (6) } # authorize = ok (6) Found Auth-Type = eap (6) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (6) authenticate { (6) eap: Expiring EAP session with state 0xf1d1cadff4e5d394 (6) eap: Finished EAP session with state 0xf1d1cadff4e5d394 (6) eap: Previous EAP request found for state 0xf1d1cadff4e5d394, released from the list (6) eap: Peer sent packet with method EAP PEAP (25) (6) eap: Calling submodule eap_peap to process data (6) eap_peap: Continuing EAP-TLS (6) eap_peap: [eaptls verify] = ok (6) eap_peap: Done initial handshake (6) eap_peap: [eaptls process] = ok (6) eap_peap: Session established. Decoding tunneled attributes (6) eap_peap: PEAP state WAITING FOR INNER IDENTITY (6) eap_peap: Identity - GalaxyS4 (6) eap_peap: Got inner identity 'GalaxyS4' (6) eap_peap: Setting default EAP type for tunneled EAP session (6) eap_peap: Got tunneled request (6) eap_peap: EAP-Message = 0x0234000d0147616c6178795334 (6) eap_peap: Setting User-Name to GalaxyS4 (6) eap_peap: Sending tunneled request to inner-tunnel (6) eap_peap: EAP-Message = 0x0234000d0147616c6178795334 (6) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1 (6) eap_peap: User-Name = "GalaxyS4" (6) eap_peap: NAS-IP-Address = 127.0.0.1 (6) eap_peap: Called-Station-Id = "98-48-27-C7-D3-CF:eduroam" (6) eap_peap: NAS-Port-Type = Wireless-802.11 (6) eap_peap: Service-Type = Framed-User (6) eap_peap: Calling-Station-Id = "CC-3A-61-98-18-B5" (6) eap_peap: Connect-Info = "CONNECT 11Mbps 802.11g" (6) eap_peap: Acct-Session-Id = "09E72C4CDC778796" (6) eap_peap: Acct-Multi-Session-Id = "E0705DD1DE6F9FEF" (6) eap_peap: WLAN-Pairwise-Cipher = 1027076 (6) eap_peap: WLAN-Group-Cipher = 1027076 (6) eap_peap: WLAN-AKM-Suite = 1027073 (6) eap_peap: Framed-MTU = 1400 (6) eap_peap: Event-Timestamp = "Oct 6 2021 17:48:25 CEST" (6) Virtual server inner-tunnel received request (6) EAP-Message = 0x0234000d0147616c6178795334 (6) FreeRADIUS-Proxied-To = 127.0.0.1 (6) User-Name = "GalaxyS4" (6) NAS-IP-Address = 127.0.0.1 (6) Called-Station-Id = "98-48-27-C7-D3-CF:eduroam" (6) NAS-Port-Type = Wireless-802.11 (6) Service-Type = Framed-User (6) Calling-Station-Id = "CC-3A-61-98-18-B5" (6) Connect-Info = "CONNECT 11Mbps 802.11g" (6) Acct-Session-Id = "09E72C4CDC778796" (6) Acct-Multi-Session-Id = "E0705DD1DE6F9FEF" (6) WLAN-Pairwise-Cipher = 1027076 (6) WLAN-Group-Cipher = 1027076 (6) WLAN-AKM-Suite = 1027073 (6) Framed-MTU = 1400 (6) Event-Timestamp = "Oct 6 2021 17:48:25 CEST" (6) WARNING: Outer and inner identities are the same. User privacy is compromised. (6) server inner-tunnel { (6) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/inner-tunnel (6) authorize { (6) policy filter_username { (6) if (&User-Name) { (6) if (&User-Name) -> TRUE (6) if (&User-Name) { (6) if (&User-Name =~ / /) { (6) if (&User-Name =~ / /) -> FALSE (6) if (&User-Name =~ /@[^@]*@/ ) { (6) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (6) if (&User-Name =~ /\.\./ ) { (6) if (&User-Name =~ /\.\./ ) -> FALSE (6) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) { (6) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE (6) if (&User-Name =~ /\.$/) { (6) if (&User-Name =~ /\.$/) -> FALSE (6) if (&User-Name =~ /@\./) { (6) if (&User-Name =~ /@\./) -> FALSE (6) } # if (&User-Name) = notfound (6) } # policy filter_username = notfound (6) [chap] = noop (6) [mschap] = noop (6) suffix: Checking for suffix after "@" (6) suffix: No '@' in User-Name = "GalaxyS4", looking up realm NULL (6) suffix: No such realm "NULL" (6) [suffix] = noop (6) eap: Peer sent EAP Response (code 2) ID 52 length 13 (6) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize (6) [eap] = ok (6) } # authorize = ok (6) Found Auth-Type = eap (6) # Executing group from file /etc/freeradius/3.0/sites-enabled/inner-tunnel (6) authenticate { (6) eap: Peer sent packet with method EAP Identity (1) (6) eap: Calling submodule eap_mschapv2 to process data (6) eap_mschapv2: Issuing Challenge (6) eap: Sending EAP Request (code 1) ID 53 length 43 (6) eap: EAP session adding &reply:State = 0x4eeeca7f4edbd02d (6) [eap] = handled (6) } # authenticate = handled (6) } # server inner-tunnel (6) Virtual server sending reply (6) EAP-Message = 0x0135002b1a0135002610c402d971e7c9a5f13f28273c8b945a20667265657261646975732d332e302e3137 (6) Message-Authenticator = 0x00000000000000000000000000000000 (6) State = 0x4eeeca7f4edbd02d7e30d0f206300d85 (6) eap_peap: Got tunneled reply code 11 (6) eap_peap: EAP-Message = 0x0135002b1a0135002610c402d971e7c9a5f13f28273c8b945a20667265657261646975732d332e302e3137 (6) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (6) eap_peap: State = 0x4eeeca7f4edbd02d7e30d0f206300d85 (6) eap_peap: Got tunneled reply RADIUS code 11 (6) eap_peap: EAP-Message = 0x0135002b1a0135002610c402d971e7c9a5f13f28273c8b945a20667265657261646975732d332e302e3137 (6) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (6) eap_peap: State = 0x4eeeca7f4edbd02d7e30d0f206300d85 (6) eap_peap: Got tunneled Access-Challenge (6) eap: Sending EAP Request (code 1) ID 53 length 74 (6) eap: EAP session adding &reply:State = 0xf1d1cadff7e4d394 (6) [eap] = handled (6) } # authenticate = handled (6) Using Post-Auth-Type Challenge (6) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (6) Challenge { ... } # empty sub-section is ignored (6) Sent Access-Challenge Id 126 from 127.0.0.1:1812 to 127.0.0.1:46839 length 0 (6) EAP-Message = 0x0135004a1900170303003f81d0ed97f89fd2f40394c8db41c255f1db3d5ffbfeea2c3def5ee43f729eb345063c678ab9ff96195a3994d7b05989c2835efdbfaa1d50d543f6ac17a9f86e (6) Message-Authenticator = 0x00000000000000000000000000000000 (6) State = 0xf1d1cadff7e4d394ae57fe37bedc2af7 (6) Finished request Waking up in 4.7 seconds. (7) Received Access-Request Id 127 from 127.0.0.1:46839 to 127.0.0.1:1812 length 314 (7) User-Name = "GalaxyS4" (7) NAS-IP-Address = 127.0.0.1 (7) Called-Station-Id = "98-48-27-C7-D3-CF:eduroam" (7) NAS-Port-Type = Wireless-802.11 (7) Service-Type = Framed-User (7) Calling-Station-Id = "CC-3A-61-98-18-B5" (7) Connect-Info = "CONNECT 11Mbps 802.11g" (7) Acct-Session-Id = "09E72C4CDC778796" (7) Acct-Multi-Session-Id = "E0705DD1DE6F9FEF" (7) WLAN-Pairwise-Cipher = 1027076 (7) WLAN-Group-Cipher = 1027076 (7) WLAN-AKM-Suite = 1027073 (7) Framed-MTU = 1400 (7) EAP-Message = 0x0235006219001703030057000000000000000243ac9e502b9baa546f286796d9586c9071947fb5a4e4165555cdb7488b72f25d5bc56695b2e42aa393376016762495b6269455dd24070c5322c8aeccac4e9c123cfcd473a483898f7ce051713d40fe (7) State = 0xf1d1cadff7e4d394ae57fe37bedc2af7 (7) Message-Authenticator = 0xe206fc169cc058271acc0a5c8c75179d (7) session-state: No cached attributes (7) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (7) authorize { (7) policy filter_username { (7) if (&User-Name) { (7) if (&User-Name) -> TRUE (7) if (&User-Name) { (7) if (&User-Name =~ / /) { (7) if (&User-Name =~ / /) -> FALSE (7) if (&User-Name =~ /@[^@]*@/ ) { (7) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (7) if (&User-Name =~ /\.\./ ) { (7) if (&User-Name =~ /\.\./ ) -> FALSE (7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) { (7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE (7) if (&User-Name =~ /\.$/) { (7) if (&User-Name =~ /\.$/) -> FALSE (7) if (&User-Name =~ /@\./) { (7) if (&User-Name =~ /@\./) -> FALSE (7) } # if (&User-Name) = notfound (7) } # policy filter_username = notfound (7) [preprocess] = ok (7) [chap] = noop (7) [mschap] = noop (7) [digest] = noop (7) suffix: Checking for suffix after "@" (7) suffix: No '@' in User-Name = "GalaxyS4", looking up realm NULL (7) suffix: No such realm "NULL" (7) [suffix] = noop (7) eap: Peer sent EAP Response (code 2) ID 53 length 98 (7) eap: Continuing tunnel setup (7) [eap] = ok (7) } # authorize = ok (7) Found Auth-Type = eap (7) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (7) authenticate { (7) eap: Expiring EAP session with state 0x4eeeca7f4edbd02d (7) eap: Finished EAP session with state 0xf1d1cadff7e4d394 (7) eap: Previous EAP request found for state 0xf1d1cadff7e4d394, released from the list (7) eap: Peer sent packet with method EAP PEAP (25) (7) eap: Calling submodule eap_peap to process data (7) eap_peap: Continuing EAP-TLS (7) eap_peap: [eaptls verify] = ok (7) eap_peap: Done initial handshake (7) eap_peap: [eaptls process] = ok (7) eap_peap: Session established. Decoding tunneled attributes (7) eap_peap: PEAP state phase2 (7) eap_peap: EAP method MSCHAPv2 (26) (7) eap_peap: Got tunneled request (7) eap_peap: EAP-Message = 0x023500431a0235003e313729dccbcf5207838b72c87d5eca018b00000000000000003b589d07adcd449ad1166846a23308004c626261203bf3a50047616c6178795334 (7) eap_peap: Setting User-Name to GalaxyS4 (7) eap_peap: Sending tunneled request to inner-tunnel (7) eap_peap: EAP-Message = 0x023500431a0235003e313729dccbcf5207838b72c87d5eca018b00000000000000003b589d07adcd449ad1166846a23308004c626261203bf3a50047616c6178795334 (7) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1 (7) eap_peap: User-Name = "GalaxyS4" (7) eap_peap: State = 0x4eeeca7f4edbd02d7e30d0f206300d85 (7) eap_peap: NAS-IP-Address = 127.0.0.1 (7) eap_peap: Called-Station-Id = "98-48-27-C7-D3-CF:eduroam" (7) eap_peap: NAS-Port-Type = Wireless-802.11 (7) eap_peap: Service-Type = Framed-User (7) eap_peap: Calling-Station-Id = "CC-3A-61-98-18-B5" (7) eap_peap: Connect-Info = "CONNECT 11Mbps 802.11g" (7) eap_peap: Acct-Session-Id = "09E72C4CDC778796" (7) eap_peap: Acct-Multi-Session-Id = "E0705DD1DE6F9FEF" (7) eap_peap: WLAN-Pairwise-Cipher = 1027076 (7) eap_peap: WLAN-Group-Cipher = 1027076 (7) eap_peap: WLAN-AKM-Suite = 1027073 (7) eap_peap: Framed-MTU = 1400 (7) eap_peap: Event-Timestamp = "Oct 6 2021 17:48:25 CEST" (7) Virtual server inner-tunnel received request (7) EAP-Message = 0x023500431a0235003e313729dccbcf5207838b72c87d5eca018b00000000000000003b589d07adcd449ad1166846a23308004c626261203bf3a50047616c6178795334 (7) FreeRADIUS-Proxied-To = 127.0.0.1 (7) User-Name = "GalaxyS4" (7) State = 0x4eeeca7f4edbd02d7e30d0f206300d85 (7) NAS-IP-Address = 127.0.0.1 (7) Called-Station-Id = "98-48-27-C7-D3-CF:eduroam" (7) NAS-Port-Type = Wireless-802.11 (7) Service-Type = Framed-User (7) Calling-Station-Id = "CC-3A-61-98-18-B5" (7) Connect-Info = "CONNECT 11Mbps 802.11g" (7) Acct-Session-Id = "09E72C4CDC778796" (7) Acct-Multi-Session-Id = "E0705DD1DE6F9FEF" (7) WLAN-Pairwise-Cipher = 1027076 (7) WLAN-Group-Cipher = 1027076 (7) WLAN-AKM-Suite = 1027073 (7) Framed-MTU = 1400 (7) Event-Timestamp = "Oct 6 2021 17:48:25 CEST" (7) WARNING: Outer and inner identities are the same. User privacy is compromised. (7) server inner-tunnel { (7) session-state: No cached attributes (7) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/inner-tunnel (7) authorize { (7) policy filter_username { (7) if (&User-Name) { (7) if (&User-Name) -> TRUE (7) if (&User-Name) { (7) if (&User-Name =~ / /) { (7) if (&User-Name =~ / /) -> FALSE (7) if (&User-Name =~ /@[^@]*@/ ) { (7) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (7) if (&User-Name =~ /\.\./ ) { (7) if (&User-Name =~ /\.\./ ) -> FALSE (7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) { (7) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE (7) if (&User-Name =~ /\.$/) { (7) if (&User-Name =~ /\.$/) -> FALSE (7) if (&User-Name =~ /@\./) { (7) if (&User-Name =~ /@\./) -> FALSE (7) } # if (&User-Name) = notfound (7) } # policy filter_username = notfound (7) [chap] = noop (7) [mschap] = noop (7) suffix: Checking for suffix after "@" (7) suffix: No '@' in User-Name = "GalaxyS4", looking up realm NULL (7) suffix: No such realm "NULL" (7) [suffix] = noop (7) eap: Peer sent EAP Response (code 2) ID 53 length 67 (7) eap: No EAP Start, assuming it's an on-going EAP conversation (7) [eap] = updated (7) files: users: Matched entry DEFAULT at line 1 (7) [files] = ok (7) [expiration] = noop (7) [logintime] = noop (7) pap: WARNING: Auth-Type already set. Not setting to PAP (7) [pap] = noop (7) if (&control:Auth-Type == "pap") { (7) if (&control:Auth-Type == "pap") -> FALSE (7) else { (7) add_user: Executing: /usr/bin/python3 /usr/local/add_user.py %{User-Name} %{outer.request:Calling-Station-Id} %{outer.request:EAP-Type} %{&control:Auth-Type}: (7) add_user: EXPAND %{User-Name} (7) add_user: --> GalaxyS4 (7) add_user: EXPAND %{outer.request:Calling-Station-Id} (7) add_user: --> CC-3A-61-98-18-B5 (7) add_user: EXPAND %{outer.request:EAP-Type} (7) add_user: --> PEAP (7) add_user: EXPAND %{&control:Auth-Type} (7) add_user: --> eap (7) add_user: Program executed successfully (7) [add_user] = ok (7) } # else = ok (7) update control { (7) Auth-Type := Accept (7) } # update control = noop (7) } # authorize = updated (7) Found Auth-Type = Accept (7) Auth-Type = Accept, accepting the user (7) # Executing section post-auth from file /etc/freeradius/3.0/sites-enabled/inner-tunnel (7) post-auth { (7) if (0) { (7) if (0) -> FALSE (7) } # post-auth = noop (7) } # server inner-tunnel (7) Virtual server sending reply (7) eap_peap: Got tunneled reply code 2 (7) eap_peap: Got tunneled reply RADIUS code 2 (7) eap_peap: Tunneled authentication was successful (7) eap_peap: SUCCESS (7) eap_peap: Saving tunneled attributes for later (7) eap: Sending EAP Request (code 1) ID 54 length 46 (7) eap: EAP session adding &reply:State = 0xf1d1cadff6e7d394 (7) [eap] = handled (7) } # authenticate = handled (7) Using Post-Auth-Type Challenge (7) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (7) Challenge { ... } # empty sub-section is ignored (7) Sent Access-Challenge Id 127 from 127.0.0.1:1812 to 127.0.0.1:46839 length 0 (7) EAP-Message = 0x0136002e1900170303002381d0ed97f89fd2f5e40d6a38f5c38f3096efc060887214b61dc93afb5651f4e60f4ded (7) Message-Authenticator = 0x00000000000000000000000000000000 (7) State = 0xf1d1cadff6e7d394ae57fe37bedc2af7 (7) Finished request Waking up in 4.7 seconds. (8) Received Access-Request Id 128 from 127.0.0.1:46839 to 127.0.0.1:1812 length 262 (8) User-Name = "GalaxyS4" (8) NAS-IP-Address = 127.0.0.1 (8) Called-Station-Id = "98-48-27-C7-D3-CF:eduroam" (8) NAS-Port-Type = Wireless-802.11 (8) Service-Type = Framed-User (8) Calling-Station-Id = "CC-3A-61-98-18-B5" (8) Connect-Info = "CONNECT 11Mbps 802.11g" (8) Acct-Session-Id = "09E72C4CDC778796" (8) Acct-Multi-Session-Id = "E0705DD1DE6F9FEF" (8) WLAN-Pairwise-Cipher = 1027076 (8) WLAN-Group-Cipher = 1027076 (8) WLAN-AKM-Suite = 1027073 (8) Framed-MTU = 1400 (8) EAP-Message = 0x0236002e19001703030023000000000000000375264be4aae1607a62de7b804ef400c9bbf5f1eb57aaad849e75e0 (8) State = 0xf1d1cadff6e7d394ae57fe37bedc2af7 (8) Message-Authenticator = 0xd5d65ed538bbbdfb134e46c149439caa (8) session-state: No cached attributes (8) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (8) authorize { (8) policy filter_username { (8) if (&User-Name) { (8) if (&User-Name) -> TRUE (8) if (&User-Name) { (8) if (&User-Name =~ / /) { (8) if (&User-Name =~ / /) -> FALSE (8) if (&User-Name =~ /@[^@]*@/ ) { (8) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (8) if (&User-Name =~ /\.\./ ) { (8) if (&User-Name =~ /\.\./ ) -> FALSE (8) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) { (8) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE (8) if (&User-Name =~ /\.$/) { (8) if (&User-Name =~ /\.$/) -> FALSE (8) if (&User-Name =~ /@\./) { (8) if (&User-Name =~ /@\./) -> FALSE (8) } # if (&User-Name) = notfound (8) } # policy filter_username = notfound (8) [preprocess] = ok (8) [chap] = noop (8) [mschap] = noop (8) [digest] = noop (8) suffix: Checking for suffix after "@" (8) suffix: No '@' in User-Name = "GalaxyS4", looking up realm NULL (8) suffix: No such realm "NULL" (8) [suffix] = noop (8) eap: Peer sent EAP Response (code 2) ID 54 length 46 (8) eap: Continuing tunnel setup (8) [eap] = ok (8) } # authorize = ok (8) Found Auth-Type = eap (8) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (8) authenticate { (8) eap: Expiring EAP session with state 0x4eeeca7f4edbd02d (8) eap: Finished EAP session with state 0xf1d1cadff6e7d394 (8) eap: Previous EAP request found for state 0xf1d1cadff6e7d394, released from the list (8) eap: Peer sent packet with method EAP PEAP (25) (8) eap: Calling submodule eap_peap to process data (8) eap_peap: Continuing EAP-TLS (8) eap_peap: [eaptls verify] = ok (8) eap_peap: Done initial handshake (8) eap_peap: [eaptls process] = ok (8) eap_peap: Session established. Decoding tunneled attributes (8) eap_peap: PEAP state send tlv success (8) eap_peap: Received EAP-TLV response (8) eap_peap: Client rejected our response. The password is probably incorrect (8) eap_peap: ERROR: We sent a success, but the client did not agree (8) eap: ERROR: Failed continuing EAP PEAP (25) session. EAP sub-module failed (8) eap: Sending EAP Failure (code 4) ID 54 length 4 (8) eap: Failed in EAP select (8) [eap] = invalid (8) } # authenticate = invalid (8) Failed to authenticate the user (8) Using Post-Auth-Type Reject (8) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (8) Post-Auth-Type REJECT { (8) attr_filter.access_reject: EXPAND %{User-Name} (8) attr_filter.access_reject: --> GalaxyS4 (8) attr_filter.access_reject: Matched entry DEFAULT at line 11 (8) [attr_filter.access_reject] = updated (8) [eap] = noop (8) policy remove_reply_message_if_eap { (8) if (&reply:EAP-Message && &reply:Reply-Message) { (8) if (&reply:EAP-Message && &reply:Reply-Message) -> FALSE (8) else { (8) [noop] = noop (8) } # else = noop (8) } # policy remove_reply_message_if_eap = noop (8) } # Post-Auth-Type REJECT = updated (8) Delaying response for 1.000000 seconds Waking up in 0.3 seconds. Waking up in 0.6 seconds. (8) Sending delayed response (8) Sent Access-Reject Id 128 from 127.0.0.1:1812 to 127.0.0.1:46839 length 44 (8) EAP-Message = 0x04360004 (8) Message-Authenticator = 0x00000000000000000000000000000000 Waking up in 3.7 seconds. (0) Cleaning up request packet ID 120 with timestamp +12 (1) Cleaning up request packet ID 121 with timestamp +12 (2) Cleaning up request packet ID 122 with timestamp +12 (3) Cleaning up request packet ID 123 with timestamp +12 (4) Cleaning up request packet ID 124 with timestamp +12 (5) Cleaning up request packet ID 125 with timestamp +12 (6) Cleaning up request packet ID 126 with timestamp +12 (7) Cleaning up request packet ID 127 with timestamp +12 (8) Cleaning up request packet ID 128 with timestamp +12 Ready to process requests -- Informativa sulla Privacy: https://www.unibs.it/it/node/1452 <https://www.unibs.it/it/node/1452>