December 2009 - Freeradius-Users - lists.freeradius.org

Re: rlm_perl authentication override
by Henry 20 Nov '12

20 Nov '12

Quoting tnt(a)kalik.net: >>>> Is there a way to change the reply from Access-Reject, to Access-Accept? >>>> > > Change freeradius.internal attribute Packet-Type in Post-Auth-Type Reject > section. Changing freeradius.internal Packet-Type from Access-Reject to Access-Accept would affect ALL logins - even logins which *should* be rejected. I'm referring to changing Access-Reject to Access-Accept under certain circumstances only -- not globally for all logins. ...or am I misunderstanding what you're suggesting? Thanks Henry

5 13

Freeradius 2 , TTLS/PAP, multiples questions
by Jérôme BERTHIER 19 Jun '12

19 Jun '12

Hi, I'm trying to configure Freeradius 2 to implement EAP/TTLS-PAP authentication method on my Cisco AP1242. It works but I'd like some precisions to get configuration files as small as possible. What is the shortest way to configure it ? authorize { preprocess auth_log suffix eap { ok = return } files ldap pap } authenticate { Auth-Type PAP { pap } Auth-Type LDAP { ldap } eap } Are the lines correct ? Moreover, I've got trouble to implement few functions. First, what's the right way to implement check for Simultaneous-Use ? For cisco nas type, Freeradius seems to use snmp check but where should I configure SNMP read community in order to make it possible ? Then, during EAP process, is it possible to check if inner identity equal outer identity and if not to reject request ? Finally, I've got problem with NetworkManager under Fedora 9 (not tested on other distribution). If Session resumption / fast reauthentication cache is not enabled, clients can't reassociate and ask for session resumption again. Is there a workaround ? Thanks -- Jérôme BERTHIER Network administrator INRIA Bordeaux - Sud-Ouest Service des Moyens Informatiques 05 24 57 40 50

4 8

EAP-TTLS-PAP-LDAP
by Rohaizam Abu Bakar 12 Jun '12

12 Jun '12

Trying to do EAP-TTLS-PAP with CRYPT passwd in LDAP.. The tunelling seems fine.. but up to comparing the password it will failed. Refer below logs & config Some says (http://felipe-alfaro.org/blog/category/radius/) PAP is tunneled inside EAP-TTLS through EAP-GTC... Tried that as well.. still same error.. gtc { auth_type = PAP [even trying to change to LDAP/OCE - still same error) } Error ==== auth: type Local auth: user supplied User-Password does NOT match local User-Password auth: Failed to validate the user. Login incorrect: [jaroce2(a)ocemy015.com] (from client localhost port 0) TTLS: Got tunneled Access-Reject rlm_eap: Handler failed in EAP/ttls rlm_eap: Failed in EAP select modcall[authenticate]: module "eap" returns invalid for request 9 modcall: leaving group authenticate (returns invalid) for request 9 auth: Failed to validate the user. Login incorrect: [jaroce2(a)ocemy015.com] (from client OCE_JARING port 241 cli 00-11-5b-2d-b2-8e) With setting:- a) radiusd.conf ldapOCE { --some setting } authorize { eap Autz-Type OCE { ldapOCE } } authenticate { Auth-Type OCE { ldapOCE } eap } b) eap.conf eap { default_eap_type = ttls tls { --some setting } ttls { default_eap_type = md5 } c) users:- DEFAULT Realm == "my015.com", Autz-Type := OCE

9 16

Daily accounting
by David Roze 02 Dec '11

02 Dec '11

Hi everyone, I have seen a lot of people who are trying to get traffic accounting collected at regular intervals to generate graphs and view per day/month etc... I have made a few modifications in order to achieve this. You can see it at http://www.netexpertise.eu/en/FreeRadius/DailyAcct.html It works on Mysql setup but can be adapted to any db. I'd be grateful to get some feedback on this. A lot of ISPs are running into this problem. Hope this helps Regards, David

2 1

ldap+freeradius
by David N'DAKPAZE 09 Nov '11

09 Nov '11

Hello, Please I 'd to know how to use an ldap as a database of freeradius. I use freeradius-server-2.1.3. Is it possible to use more than one nas in clients.conf ? If yes how to do it? How to configure EAP-TLS ? Thank you for your help. Rato

9 61

rlm_sql: "NUMERIC VALUE OUT OF RANGE" error
by Vegard Svanberg 07 Jul '11

07 Jul '11

Freeradius 2.1.0. I have a NAS which sends a NAS-Port-Id attribute in the range 2147483648..2164260863. PostgreSQL doesn't like the query Freeradius performs. It's choking when trying to insert for instance '2163214239::integer' into the radacct table. $ select 2163214239::integer; ERROR: integer out of range Example: INSERT INTO radacct (AcctSessionId, AcctUniqueId, UserName, Realm, NASIPAddress, NASPortId, NASPortType, AcctStartTime, AcctStopTime, AcctSessionTime, AcctAuthentic, ConnectInfo_stop, AcctInputOctets, AcctOutputOctets, CalledStationId, CallingStationId, AcctTerminateCause, ServiceType, FramedProtocol, FramedIPAddress, AcctStopDelay) values('80f0079f', '5c9f0b7076dcc9c0', 'username', NULLIF('', ''), '1.2.3.4', 2163214239::integer, 'Wireless-802.11', ('2008-09-26 09:52:52'::timestamp - '1'::interval - '3382'::interval), ('2008-09-26 09:52:52'::timestamp - '1'::interval), NULLIF('3382', '')::bigint, '', '', (('0'::bigint << 32) + '57743'::bigint), (('0'::bigint << 32) + '294709'::bigint), 'hotspot', 'XX:XX:XX:XX:XX:XX', 'Lost-Service', '', '', NULLIF('192.168.12.94', '')::inet, 0) rlm_sql_postgresql: Status: PGRES_FATAL_ERROR rlm_sql_postgresql: Error integer out of range rlm_sql_postgresql: Postgresql Fatal Error: [22003: NUMERIC VALUE OUT OF RANGE] Occurred!! [sql] Couldn't insert SQL accounting STOP record - ERROR: integer out of range rlm_sql (sql): Released sql socket id: 3 ++[sql] returns fail Quick fixes...? -- Vegard Svanberg <vegard(a)svanberg.no> [*Takapa@IRC (EFnet)]

6 6

Re: Unable to find module....
by Bryan Graham 23 Jun '11

23 Jun '11

Bryan Graham wrote: >> /opt/csg/etc/raddb/sites-enabled/default[198]: Failed to find module >> "attr_rewrite". >> /opt/csg/etc/raddb/sites-enabled/default[62]: Errors parsing authorize >> section. Alan DeKok wrote: > That message is produced when the module doesn't exist, OR when it has >failed to initialize properly. > > e.g. There is an error in it's configuration, or in the files that it >is reading. The error WILL be printed just above the lines you quoted. > > Alan DeKok. Well, I didn't want to include the whole thing, because it's long, but here goes: /opt/csg/sbin/radiusd -X FreeRADIUS Version 2.1.5, for host sparc-sun-solaris2.10, built on Mar 10 2009 at 15:36:40 Copyright (C) 1999-2008 The FreeRADIUS server project and contributors. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. You may redistribute copies of FreeRADIUS under the terms of the GNU General Public License v2. Starting - reading configuration files ... including configuration file /opt/csg/etc/raddb/radiusd.conf including configuration file /opt/csg/etc/raddb/clients.conf including files in directory /opt/csg/etc/raddb/modules/ including configuration file /opt/csg/etc/raddb/modules/acct_unique including configuration file /opt/csg/etc/raddb/modules/always including configuration file /opt/csg/etc/raddb/modules/attr_filter including configuration file /opt/csg/etc/raddb/modules/attr_rewrite including configuration file /opt/csg/etc/raddb/modules/chap including configuration file /opt/csg/etc/raddb/modules/checkval including configuration file /opt/csg/etc/raddb/modules/counter including configuration file /opt/csg/etc/raddb/modules/detail including configuration file /opt/csg/etc/raddb/modules/detail.example.com including configuration file /opt/csg/etc/raddb/modules/detail.log including configuration file /opt/csg/etc/raddb/modules/digest including configuration file /opt/csg/etc/raddb/modules/echo including configuration file /opt/csg/etc/raddb/modules/etc_group including configuration file /opt/csg/etc/raddb/modules/exec including configuration file /opt/csg/etc/raddb/modules/expiration including configuration file /opt/csg/etc/raddb/modules/expr including configuration file /opt/csg/etc/raddb/modules/files including configuration file /opt/csg/etc/raddb/modules/inner-eap including configuration file /opt/csg/etc/raddb/modules/ippool including configuration file /opt/csg/etc/raddb/modules/krb5 including configuration file /opt/csg/etc/raddb/modules/ldap including configuration file /opt/csg/etc/raddb/modules/linelog including configuration file /opt/csg/etc/raddb/modules/logintime including configuration file /opt/csg/etc/raddb/modules/mac2ip including configuration file /opt/csg/etc/raddb/modules/mac2vlan including configuration file /opt/csg/etc/raddb/modules/otp including configuration file /opt/csg/etc/raddb/modules/mschap including configuration file /opt/csg/etc/raddb/modules/pam including configuration file /opt/csg/etc/raddb/modules/pap including configuration file /opt/csg/etc/raddb/modules/passwd including configuration file /opt/csg/etc/raddb/modules/perl including configuration file /opt/csg/etc/raddb/modules/policy including configuration file /opt/csg/etc/raddb/modules/preprocess including configuration file /opt/csg/etc/raddb/modules/radutmp including configuration file /opt/csg/etc/raddb/modules/realm including configuration file /opt/csg/etc/raddb/modules/smbpasswd including configuration file /opt/csg/etc/raddb/modules/smsotp including configuration file /opt/csg/etc/raddb/modules/sql_log including configuration file /opt/csg/etc/raddb/modules/sqlcounter_expire_on_login including configuration file /opt/csg/etc/raddb/modules/sradutmp including configuration file /opt/csg/etc/raddb/modules/unix including configuration file /opt/csg/etc/raddb/modules/wimax including configuration file /opt/csg/etc/raddb/policy.conf including files in directory /opt/csg/etc/raddb/sites-enabled/ including configuration file /opt/csg/etc/raddb/sites-enabled/default including dictionary file /opt/csg/etc/raddb/dictionary main { prefix = "/opt/csg" localstatedir = "/opt/csg/var" logdir = "/opt/csg/var/log/radius" libdir = "/opt/csg/lib" radacctdir = "/opt/csg/var/log/radius/radacct" hostname_lookups = no max_request_time = 30 cleanup_delay = 5 max_requests = 1024 allow_core_dumps = no pidfile = "/opt/csg/var/run/radiusd/radiusd.pid" checkrad = "/opt/csg/sbin/checkrad" debug_level = 0 proxy_requests = no log { stripped_names = no auth = yes auth_badpass = no auth_goodpass = no } security { max_attributes = 200 reject_delay = 1 status_server = yes } } radiusd: #### Loading Realms and Home Servers #### radiusd: #### Loading Clients #### client localhost { ipaddr = xxx.xxx.xxx.xxx require_message_authenticator = no secret = "ihatetesting" shortname = "localhost" nastype = "other" } radiusd: #### Instantiating modules #### instantiate { Module: Linked to module rlm_exec Module: Instantiating exec exec { wait = no input_pairs = "request" shell_escape = yes } Module: Linked to module rlm_expr Module: Instantiating expr Module: Linked to module rlm_expiration Module: Instantiating expiration expiration { reply-message = "Password Has Expired " } Module: Linked to module rlm_logintime Module: Instantiating logintime logintime { reply-message = "You are calling outside your allowed timespan " minimum-timeout = 60 } } radiusd: #### Loading Virtual Servers #### modules { Module: Checking authenticate {...} for more modules to load Module: Linked to module rlm_krb5 Module: Instantiating krb5 krb5 { keytab = "/opt/csg/etc/raddb/radius.keytab" service_principal = "admin/radius" } rlm_krb5: krb5_init ok Module: Checking authorize {...} for more modules to load Module: Linked to module rlm_preprocess Module: Instantiating preprocess preprocess { huntgroups = "/opt/csg/etc/raddb/huntgroups" hints = "/opt/csg/etc/raddb/hints" with_ascend_hack = no ascend_channels_per_line = 23 with_ntdomain_hack = no with_specialix_jetstream_hack = no with_cisco_vsa_hack = no with_alvarion_vsa_hack = no } Module: Linked to module rlm_files Module: Instantiating files files { usersfile = "/opt/csg/etc/raddb/users" acctusersfile = "/opt/csg/etc/raddb/acct_users" preproxy_usersfile = "/opt/csg/etc/raddb/preproxy_users" compat = "no" } Module: Linked to module rlm_ldap Module: Instantiating ldap ldap { server = "ldap.somedomain.com" port = 389 password = "AequieCi8" identity = "cn=radius,ou=Special,dc=cs,dc=tamu,dc=edu" net_timeout = 1 timeout = 4 timelimit = 3 tls_mode = no start_tls = no tls_require_cert = "allow" tls { start_tls = yes require_cert = "allow" } basedn = "ou=People,dc=cs,dc=tamu,dc=edu" filter = "(uid=%{%{Callback-Number}:-%{User-Name}})" base_filter = "(objectclass=radiusprofile)" auto_header = no access_attr_used_for_allow = yes groupname_attribute = "cn" groupmembership_filter = "(|(&(objectClass=GroupOfNames)(member=%{Ldap-UserDn}))(&(objectClass=GroupOfUniqueNames)(uniquemember=%{Ldap-UserDn})))" dictionary_mapping = "/opt/csg/etc/raddb/ldap.attrmap" ldap_debug = 0 ldap_connections_number = 5 compare_check_items = no do_xlat = yes set_auth_type = no } rlm_ldap: Registering ldap_groupcmp for Ldap-Group rlm_ldap: Registering ldap_xlat with xlat_name ldap rlm_ldap: reading ldap<->radius mappings from file /opt/csg/etc/raddb/ldap.attrmap rlm_ldap: LDAP radiusCheckItem mapped to RADIUS $GENERIC$ rlm_ldap: LDAP radiusReplyItem mapped to RADIUS $GENERIC$ rlm_ldap: LDAP radiusAuthType mapped to RADIUS Auth-Type rlm_ldap: LDAP radiusSimultaneousUse mapped to RADIUS Simultaneous-Use rlm_ldap: LDAP radiusCalledStationId mapped to RADIUS Called-Station-Id rlm_ldap: LDAP radiusCallingStationId mapped to RADIUS Calling-Station-Id rlm_ldap: LDAP lmPassword mapped to RADIUS LM-Password rlm_ldap: LDAP ntPassword mapped to RADIUS NT-Password rlm_ldap: LDAP sambaLmPassword mapped to RADIUS LM-Password rlm_ldap: LDAP sambaNtPassword mapped to RADIUS NT-Password rlm_ldap: LDAP dBCSPwd mapped to RADIUS LM-Password rlm_ldap: LDAP acctFlags mapped to RADIUS SMB-Account-CTRL-TEXT rlm_ldap: LDAP radiusExpiration mapped to RADIUS Expiration rlm_ldap: LDAP radiusNASIpAddress mapped to RADIUS NAS-IP-Address rlm_ldap: LDAP radiusServiceType mapped to RADIUS Service-Type rlm_ldap: LDAP radiusFramedProtocol mapped to RADIUS Framed-Protocol rlm_ldap: LDAP radiusFramedIPAddress mapped to RADIUS Framed-IP-Address rlm_ldap: LDAP radiusFramedIPNetmask mapped to RADIUS Framed-IP-Netmask rlm_ldap: LDAP radiusFramedRoute mapped to RADIUS Framed-Route rlm_ldap: LDAP radiusFramedRouting mapped to RADIUS Framed-Routing rlm_ldap: LDAP radiusFilterId mapped to RADIUS Filter-Id rlm_ldap: LDAP radiusFramedMTU mapped to RADIUS Framed-MTU rlm_ldap: LDAP radiusFramedCompression mapped to RADIUS Framed-Compression rlm_ldap: LDAP radiusLoginIPHost mapped to RADIUS Login-IP-Host rlm_ldap: LDAP radiusLoginService mapped to RADIUS Login-Service rlm_ldap: LDAP radiusLoginTCPPort mapped to RADIUS Login-TCP-Port rlm_ldap: LDAP radiusCallbackNumber mapped to RADIUS Callback-Number rlm_ldap: LDAP radiusCallbackId mapped to RADIUS Callback-Id rlm_ldap: LDAP radiusFramedIPXNetwork mapped to RADIUS Framed-IPX-Network rlm_ldap: LDAP radiusClass mapped to RADIUS Class rlm_ldap: LDAP radiusSessionTimeout mapped to RADIUS Session-Timeout rlm_ldap: LDAP radiusIdleTimeout mapped to RADIUS Idle-Timeout rlm_ldap: LDAP radiusTerminationAction mapped to RADIUS Termination-Action rlm_ldap: LDAP radiusLoginLATService mapped to RADIUS Login-LAT-Service rlm_ldap: LDAP radiusLoginLATNode mapped to RADIUS Login-LAT-Node rlm_ldap: LDAP radiusLoginLATGroup mapped to RADIUS Login-LAT-Group rlm_ldap: LDAP radiusFramedAppleTalkLink mapped to RADIUS Framed-AppleTalk-Link rlm_ldap: LDAP radiusFramedAppleTalkNetwork mapped to RADIUS Framed-AppleTalk-Network rlm_ldap: LDAP radiusFramedAppleTalkZone mapped to RADIUS Framed-AppleTalk-Zone rlm_ldap: LDAP radiusPortLimit mapped to RADIUS Port-Limit rlm_ldap: LDAP radiusLoginLATPort mapped to RADIUS Login-LAT-Port rlm_ldap: LDAP radiusReplyMessage mapped to RADIUS Reply-Message conns: 87848 /opt/csg/etc/raddb/sites-enabled/default[198]: Failed to find module "attr_rewrite". /opt/csg/etc/raddb/sites-enabled/default[62]: Errors parsing authorize section. } Errors initializing modules That's my radiusd output, and I don't see anything about attr_rewrite at all. In addition, here's the contents of some of my lib dir (the whole thing is long): [root]@radius /opt/csg/lib> (08:03:07 04/07/09) :: ls rlm_attr* rlm_attr_filter-2.1.5.la rlm_attr_filter.a rlm_attr_filter.so rlm_attr_rewrite-2.1.5.so rlm_attr_rewrite.la rlm_attr_filter-2.1.5.so rlm_attr_filter.la rlm_attr_rewrite-2.1.5.la rlm_attr_rewrite.a rlm_attr_rewrite.so This is the same dir were rlm_ldap and rlm_krb5 (successfully loaded) all reside as well, so you can understand my confusion. thanks, Bryan Graham

3 2

Calling-Station-ID not sent by pam_radius_auth.
by Christiaan Ehlers 25 May '11

25 May '11

Hi I currently running the following system: Server: FreeRadius, MySQL Client: pam_radius_auth, libnss_mysql.so I use the freeradius to auth and account ssh logins, here is my pam.d/sshd file on the client. #%PAM-1.0 auth sufficient /lib/security/pam_radius_auth.so debug auth required /lib/security/pam_stack.so service=system-auth auth required /lib/security/pam_nologin.so account sufficient /lib/security/pam_radius_auth.so debug account required /lib/security/pam_stack.so service=system-auth password required /lib/security/pam_stack.so service=system-auth session required /lib/security/pam_mkhomedir.so skel=/etc/skel/ umask=0022 session sufficient /lib/security/pam_radius_auth.so debug conf=/etc/radiusclient/servers session required /lib/security/pam_stack.so service=system-auth session required /lib/security/pam_limits.so session optional /lib/security/pam_console.so Now when I authenticate I can see that the Calling-Station-ID gets passed, but when I do authentication that field seems to be missing. Here is the output of radiusd -X Ready to process requests. rad_recv: Access-Request packet from host 10.0.0.1:3698, id=220, length=89 User-Name = "test" User-Password = "123pass" NAS-IP-Address = 10.0.0.1 NAS-Identifier = "sshd" NAS-Port = 2673 NAS-Port-Type = Virtual Service-Type = Authenticate-Only Calling-Station-Id = "10.1.1.1" Processing the authorize section of radiusd.conf modcall: entering group authorize for request 0 modcall[authorize]: module "preprocess" returns ok for request 0 modcall[authorize]: module "chap" returns noop for request 0 modcall[authorize]: module "mschap" returns noop for request 0 rlm_realm: No '@' in User-Name = "test", looking up realm NULL rlm_realm: No such realm "NULL" modcall[authorize]: module "suffix" returns noop for request 0 rlm_eap: No EAP-Message, not doing EAP modcall[authorize]: module "eap" returns noop for request 0 users: Matched entry DEFAULT at line 153 modcall[authorize]: module "files" returns ok for request 0 radius_xlat: 'test' rlm_sql (sql): sql_set_user escaped user --> 'test' radius_xlat: 'SELECT id,UserName,Attribute,Value,op FROM radcheck WHERE Username = 'test' ORDER BY id' rlm_sql (sql): Reserving sql socket id: 7 radius_xlat: 'SELECT radgroupcheck.id,radgroupcheck.GroupName,radgroupcheck.Attribute,radgroupche ck.Value,radgroupcheck.op FROM radgroupcheck,usergroup WHERE usergroup.Username = 'test' AND usergroup.GroupName = radgroupcheck.GroupName ORDER BY radgroupcheck.id' radius_xlat: 'SELECT id,UserName,Attribute,Value,op FROM radreply WHERE Username = 'test' ORDER BY id' radius_xlat: 'SELECT radgroupreply.id,radgroupreply.GroupName,radgroupreply.Attribute,radgrouprep ly.Value,radgroupreply.op FROM radgroupreply,usergroup WHERE usergroup.Username = 'test' AND usergroup.GroupName = radgroupreply.GroupName ORDER BY radgroupreply.id' rlm_sql (sql): Released sql socket id: 7 modcall[authorize]: module "sql" returns ok for request 0 modcall: group authorize returns ok for request 0 rad_check_password: Found Auth-Type pap auth: type "PAP" Processing the authenticate section of radiusd.conf modcall: entering group Auth-Type for request 0 rlm_pap: login attempt by "test" with password 123pass rlm_pap: Using password "$1$n/uxpq.r$FBKqAEC8KvsK13QVHRwAf/" for user test authentication. rlm_pap: Using CRYPT encryption. rlm_pap: User authenticated succesfully modcall[authenticate]: module "pap" returns ok for request 0 modcall: group Auth-Type returns ok for request 0 Sending Access-Accept of id 220 to 10.0.0.1:3698 Framed-IP-Address := 10.1.1.1 Framed-Protocol := PPP Service-Type := Framed-User Framed-Compression := Van-Jacobson-TCP-IP Finished request 0 Going to the next request --- Walking the entire request list --- Waking up in 6 seconds... rad_recv: Accounting-Request packet from host 10.0.0.1:3698, id=66, length=72 User-Name = "test" NAS-IP-Address = 10.0.0.1 NAS-Identifier = "sshd" NAS-Port = 2673 NAS-Port-Type = Virtual Acct-Status-Type = Start Acct-Session-Id = "00002673" Acct-Authentic = RADIUS Processing the preacct section of radiusd.conf modcall: entering group preacct for request 1 modcall[preacct]: module "preprocess" returns noop for request 1 rlm_acct_unique: Hashing 'NAS-Port = 2673,Client-IP-Address = 10.0.0.1,NAS-IP-Address = 10.0.0.1,Acct-Session-Id = "00002673",User-Name = "test"' rlm_acct_unique: Acct-Unique-Session-ID = "a0ec8ab13c262f56". modcall[preacct]: module "acct_unique" returns ok for request 1 rlm_realm: No '@' in User-Name = "test", looking up realm NULL rlm_realm: No such realm "NULL" modcall[preacct]: module "suffix" returns noop for request 1 modcall[preacct]: module "files" returns noop for request 1 modcall: group preacct returns ok for request 1 Processing the accounting section of radiusd.conf modcall: entering group accounting for request 1 radius_xlat: '/usr/local/var/log/radius/radacct/10.0.0.1/detail-20050603' rlm_detail: /usr/local/var/log/radius/radacct/%{Client-IP-Address}/detail-%Y%m%d expands to /usr/local/var/log/radius/radacct/10.0.0.1/detail-20050603 modcall[accounting]: module "detail" returns ok for request 1 modcall[accounting]: module "unix" returns ok for request 1 radius_xlat: '/usr/local/var/log/radius/radutmp' radius_xlat: 'test' modcall[accounting]: module "radutmp" returns ok for request 1 radius_xlat: 'test' rlm_sql (sql): sql_set_user escaped user --> 'test' radius_xlat: 'INSERT into radacct (AcctSessionId, AcctUniqueId, UserName, Realm, NASIPAddress, NASPortId, NASPortType, AcctStartTime, AcctStopTime, AcctSessionTime, AcctAuthentic, ConnectInfo_start, ConnectInfo_stop, AcctInputOctets, AcctOutputOctets, CalledStationId, CallingStationId, AcctTerminateCause, ServiceType, FramedProtocol, FramedIPAddress, AcctStartDelay, AcctStopDelay) values('00002673', 'a0ec8ab13c262f56', 'test', '', '10.0.0.1', '2673', 'Virtual', '2005-06-03 14:20:01', '0', '0', 'RADIUS', '', '', '0', '0', '', '', '', '', '', '', '', '0')' rlm_sql (sql): Reserving sql socket id: 6 rlm_sql (sql): Released sql socket id: 6 modcall[accounting]: module "sql" returns ok for request 1 modcall: group accounting returns ok for request 1 Sending Accounting-Response of id 66 to 10.0.0.1:3698 Finished request 1 Going to the next request Cleaning up request 1 ID 66 with timestamp 42a05901 Waking up in 6 seconds... --- Walking the entire request list --- Cleaning up request 0 ID 220 with timestamp 42a05901 Nothing to do. Sleeping until we see a request. As you can see the CallingStationId is empty, also there is no mention of it in the Accounting request packet. If this is not supported by the accounting, is there a way to get it from the authentication section? Would also like to say that I know this is more related to the PAM module and I assume this makes this mail a bit out of context in this mail group, but any help would be most appreciated. Kind Regards Christiaan Ehlers

4 3

FR 2.1.0 (ubuntu) proxying to NPS/IAS.
by Ville Leinonen 02 Feb '11

02 Feb '11

Hi, I try to use FR to forwarding access-request to NPS servers, but some reason FR/NPS gives "User password is incorrect" message. I have tripple check that password is correct. When i test IAS to NPS proxy it works. I have enable in NPS side MS-CHAP-v2, MS-CHAP, CHAP and PAP/SPAP methods. Any clue what is wrong? Here is some logs: rad_recv: Access-Request packet from host 192.168.21.150 port 1025, id=57, length=154 User-Name = "vle" User-Password = "\2063\261m\301\344J\216sCÑ \035\003\2328" NAS-Port = 626688 Called-Station-Id = "192.168.21.150" Calling-Station-Id = "192.168.1.114" NAS-Port-Type = Virtual Tunnel-Client-Endpoint:0 = "192.168.1.114" NAS-IP-Address = 192.168.21.150 Cisco-AVPair = "ip:source-ip=192.168.1.114" +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "vle", looking up realm NULL [suffix] Found realm "NULL" [suffix] Adding Stripped-User-Name = "vle" [suffix] Adding Realm = "NULL" [suffix] Proxying request from user vle to realm NULL [suffix] Preparing to proxy authentication request to realm "NULL" ++[suffix] returns updated [eap] No EAP-Message, not doing EAP ++[eap] returns noop ++[unix] returns notfound ++[files] returns noop ++[expiration] returns noop ++[logintime] returns noop ++[pap] returns noop +- entering group pre-proxy {...} ++[files] returns noop Sending Access-Request of id 118 to 192.168.21.200 port 1812 User-Name = "vle" User-Password = "\2063\261m\301\344J\216sCÑ \035\003\2328" NAS-Port = 626688 Called-Station-Id = "192.168.21.150" Calling-Station-Id = "192.168.1.114" NAS-Port-Type = Virtual Tunnel-Client-Endpoint:0 = "192.168.1.114" NAS-IP-Address = 192.168.21.150 Cisco-AVPair = "ip:source-ip=192.168.1.114" Proxy-State = 0x3537 Proxying request 0 to home server 192.168.21.200 port 1812 Sending Access-Request of id 118 to 192.168.21.200 port 1812 User-Name = "vle" User-Password = "\2063\261m\301\344J\216sCÑ \035\003\2328" NAS-Port = 626688 Called-Station-Id = "192.168.21.150" Calling-Station-Id = "192.168.1.114" NAS-Port-Type = Virtual Tunnel-Client-Endpoint:0 = "192.168.1.114" NAS-IP-Address = 192.168.21.150 Cisco-AVPair = "ip:source-ip=192.168.1.114" Proxy-State = 0x3537 Going to the next request Waking up in 0.9 seconds. rad_recv: Access-Reject packet from host 192.168.21.200 port 1812, id=118, length=52 Proxy-State = 0x3537 Reply-Message = "User password is incorrect" Br, Ville

6 11

Certificate-based client side authentication towards a website with freeradius
by Martin Schneider 01 Dec '10

01 Dec '10

Hello all, we're trying to setup a freeradius / apache installation that allows us to authenticate and authorize users with *certificates* towards a website. Is there a good tutorial out there somewhere? We did only finde partial information that seems to be quite old unfortunately. Or could somebody who is deep into this matter please give some advice or ideas how we can solve our task? Best regards M

5 10