June 2012 - Freeradius-Users - lists.freeradius.org

FreeRadius2 & Krb
by Lisa Besko 25 Jun '12

25 Jun '12

I'm trying to get FreeRadius2 to authenicate with MIT Kerberos. When radius enters kerberos, it dies with no message. Any suggestions on where to look for clues? OS: FreeBSD 9 Radius: FreeRadius 2.1.12 Kerberos: MIT Kbr5 1.9.2 I'm not seeing obvious errors in Debug output. [pap] WARNING! No "known good" password found for the user. Authentication may fail because of this. ++[pap] returns noop Found Auth-Type = Kerberos # Executing group from file /usr/local/etc/raddb/sites-enabled/default +- entering group Kerberos {...} I have experience configuring FreeRadius the original but was hoping to move to 2. LB

4 8

Re: EAP-TLS used to be working, replaced Wifi AP, reimported backed-up config, EAP-TLS not working anymore
by Alan Buxey 25 Jun '12

25 Jun '12

If you haven't touched FR then don't look there as that's not what has changed. Tour problem has already been identified - the bit that got changed. No changes should be made on FR or on the clients alan

3 4

Re: FreeRadius2(certos)+cisco2950+wpa_supplicant(win7) can't work with EAP-TLS
by 关旭 24 Jun '12

24 Jun '12

Thank you for your reply! Your means is WARNING: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! WARNING: !! EAP session for state 0x24e5fa322535f760 did not finish! WARNING: !! Please read http://wiki.freeradius.org/Certificate_Compatibility WARNING: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! ? I don't think is this,beause my client is wpa_supplicant not MS client, and eapol_test work fine. On wpa_supplicant log,we can see: EAP-TLS: Start SSL: (where=0x10 ret=0x1) SSL: (where=0x1001 ret=0x1) SSL: SSL_connect:before/connect initialization SSL: (where=0x1001 ret=0x1) SSL: SSL_connect:SSLv3 write client hello A SSL: (where=0x1002 ret=0xffffffff) SSL: SSL_connect:error in SSLv3 read server hello A SSL: SSL_connect - want more data SSL: 88 bytes pending from ssl_out SSL: 88 bytes left to be sent out (of total 88 bytes) The TLS just begin , and no certificate be used. By wireshark,I catch these: 62 24.202360000 Cisco_f5:47:d1 WistronI_20:c6:3d EAP 60 Unknown code (0x56) 127 54.201965000 Cisco_f5:47:d1 WistronI_20:c6:3d EAP 60 Failure 128 54.203784000 Cisco_f5:47:d1 WistronI_20:c6:3d EAP 60 Failure 129 54.204412000 Cisco_f5:47:d1 WistronI_20:c6:3d EAP 60 Request, Identity [RFC3748] 130 54.291453000 WistronI_20:c6:3d Nearest EAP 28 Response, Identity [RFC3748] 131 54.307143000 Cisco_f5:47:d1 WistronI_20:c6:3d EAP 60 Request, EAP-TLS [RFC5216] [Aboba] 132 54.338037000 WistronI_20:c6:3d Nearest SSL 118 Client Hello 133 54.366527000 Cisco_f5:47:d1 WistronI_20:c6:3d EAP 60 Unknown code (0x56) 200 84.364442000 Cisco_f5:47:d1 WistronI_20:c6:3d EAP 60 Unknown code (0x56) -----邮件原件----- 发件人: freeradius-users-bounces+guanxu=aotuis.com(a)lists.freeradius.org [mailto:freeradius-users-bounces+guanxu=aotuis.com@lists.freeradius.org] 代表 Alan DeKok 发送时间: 2012年6月24日 19:28 收件人: FreeRadius users mailing list 主题: Re: FreeRadius2(certos)+cisco2950+wpa_supplicant(win7) can't work with EAP-TLS 关旭 wrote: > Just like the title,it work fine when I use MSCHAPV2 or MD5, > But PEAP and EAP-TLS not works. > > I test Radius with eapol_test,It also work fine. > > Who can tell me the reason? The debug log you posted has the answer. In big bold letters. Read it. Alan DeKok. - List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html

2 1

FreeRadius2(certos)+cisco2950+wpa_supplicant(win7) can't work with EAP-TLS
by 关旭 24 Jun '12

24 Jun '12

Hi! Just like the title,it work fine when I use MSCHAPV2 or MD5, But PEAP and EAP-TLS not works. I test Radius with eapol_test,It also work fine. Who can tell me the reason? WPA_supplicant config file ,Radius log, WPA_supplicant log as follow: The WPA_supplicant config: network={ eap=TLS eapol_flags=0 key_mgmt=IEEE8021X identity="steve" ca_cert="d:/certs/ca.pem" client_cert="d:/certs/client.pem" private_key="d:/certs/client.key" private_key_passwd="whatever" } Radius Log: FreeRADIUS Version 2.1.12, for host i686-redhat-linux-gnu, built on Feb 22 2012 at 15:07:38 Copyright (C) 1999-2009 The FreeRADIUS server project and contributors. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. You may redistribute copies of FreeRADIUS under the terms of the GNU General Public License v2. Starting - reading configuration files ... including configuration file /etc/raddb/radiusd.conf …… radiusd: #### Instantiating modules #### instantiate { Module: Linked to module rlm_exec Module: Instantiating module "exec" from file /etc/raddb/modules/exec exec { wait = no input_pairs = "request" shell_escape = yes } Module: Linked to module rlm_expr Module: Instantiating module "expr" from file /etc/raddb/modules/expr Module: Linked to module rlm_expiration Module: Instantiating module "expiration" from file /etc/raddb/modules/expiration expiration { reply-message = "Password Has Expired " } Module: Linked to module rlm_logintime Module: Instantiating module "logintime" from file /etc/raddb/modules/logintime logintime { reply-message = "You are calling outside your allowed timespan " minimum-timeout = 60 } } radiusd: #### Loading Virtual Servers #### server { # from file /etc/raddb/radiusd.conf modules { Module: Creating Auth-Type = digest Module: Creating Post-Auth-Type = REJECT Module: Checking authenticate {...} for more modules to load Module: Linked to module rlm_pap Module: Instantiating module "pap" from file /etc/raddb/modules/pap pap { encryption_scheme = "auto" auto_header = no } Module: Linked to module rlm_chap Module: Instantiating module "chap" from file /etc/raddb/modules/chap Module: Linked to module rlm_mschap Module: Instantiating module "mschap" from file /etc/raddb/modules/mschap mschap { use_mppe = yes require_encryption = no require_strong = no with_ntdomain_hack = no allow_retry = yes } Module: Linked to module rlm_digest Module: Instantiating module "digest" from file /etc/raddb/modules/digest Module: Linked to module rlm_unix Module: Instantiating module "unix" from file /etc/raddb/modules/unix unix { radwtmp = "/var/log/radius/radwtmp" } Module: Linked to module rlm_eap Module: Instantiating module "eap" from file /etc/raddb/eap.conf eap { default_eap_type = "tls" timer_expire = 60 ignore_unknown_eap_types = no cisco_accounting_username_bug = no max_sessions = 4096 } Module: Linked to sub-module rlm_eap_md5 Module: Instantiating eap-md5 Module: Linked to sub-module rlm_eap_leap Module: Instantiating eap-leap Module: Linked to sub-module rlm_eap_gtc Module: Instantiating eap-gtc gtc { challenge = "Password: " auth_type = "PAP" } Module: Linked to sub-module rlm_eap_tls Module: Instantiating eap-tls tls { rsa_key_exchange = no dh_key_exchange = yes rsa_key_length = 512 dh_key_length = 512 verify_depth = 0 CA_path = "/etc/raddb/certs" pem_file_type = yes private_key_file = "/etc/raddb/certs/server.pem" certificate_file = "/etc/raddb/certs/server.pem" CA_file = "/etc/raddb/certs/ca.pem" private_key_password = "whatever" dh_file = "/etc/raddb/certs/dh" random_file = "/etc/raddb/certs/random" fragment_size = 1024 include_length = yes check_crl = no cipher_list = "DEFAULT" cache { enable = no lifetime = 24 max_entries = 255 } verify { } ocsp { enable = no override_cert_url = yes url = "http://127.0.0.1/ocsp/" } } Module: Linked to sub-module rlm_eap_ttls Module: Instantiating eap-ttls ttls { default_eap_type = "md5" copy_request_to_tunnel = no use_tunneled_reply = no virtual_server = "inner-tunnel" include_length = yes } Module: Linked to sub-module rlm_eap_peap Module: Instantiating eap-peap peap { default_eap_type = "mschapv2" copy_request_to_tunnel = no use_tunneled_reply = no proxy_tunneled_request_as_eap = yes virtual_server = "inner-tunnel" soh = no } Module: Linked to sub-module rlm_eap_mschapv2 Module: Instantiating eap-mschapv2 mschapv2 { with_ntdomain_hack = no send_error = no } Module: Checking authorize {...} for more modules to load Module: Linked to module rlm_preprocess Module: Instantiating module "preprocess" from file /etc/raddb/modules/preprocess preprocess { huntgroups = "/etc/raddb/huntgroups" hints = "/etc/raddb/hints" with_ascend_hack = no ascend_channels_per_line = 23 with_ntdomain_hack = no with_specialix_jetstream_hack = no with_cisco_vsa_hack = no with_alvarion_vsa_hack = no } Module: Linked to module rlm_realm Module: Instantiating module "suffix" from file /etc/raddb/modules/realm realm suffix { format = "suffix" delimiter = "@" ignore_default = no ignore_null = no } Module: Linked to module rlm_files Module: Instantiating module "files" from file /etc/raddb/modules/files files { usersfile = "/etc/raddb/users" acctusersfile = "/etc/raddb/acct_users" preproxy_usersfile = "/etc/raddb/preproxy_users" compat = "no" } Module: Checking preacct {...} for more modules to load Module: Linked to module rlm_acct_unique Module: Instantiating module "acct_unique" from file /etc/raddb/modules/acct_unique acct_unique { key = "User-Name, Acct-Session-Id, NAS-IP-Address, Client-IP-Address, NAS-Port" } Module: Checking accounting {...} for more modules to load Module: Linked to module rlm_detail Module: Instantiating module "detail" from file /etc/raddb/modules/detail detail { detailfile = "/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Addre ss}}/detail-%Y%m%d" header = "%t" detailperm = 384 dirperm = 493 locking = no log_packet_header = no } Module: Linked to module rlm_radutmp Module: Instantiating module "radutmp" from file /etc/raddb/modules/radutmp radutmp { filename = "/var/log/radius/radutmp" username = "%{User-Name}" case_sensitive = yes check_with_nas = yes perm = 384 callerid = yes } Module: Linked to module rlm_attr_filter Module: Instantiating module "attr_filter.accounting_response" from file /etc/raddb/modules/attr_filter attr_filter attr_filter.accounting_response { attrsfile = "/etc/raddb/attrs.accounting_response" key = "%{User-Name}" relaxed = no } Module: Checking session {...} for more modules to load Module: Checking post-proxy {...} for more modules to load Module: Checking post-auth {...} for more modules to load Module: Instantiating module "attr_filter.access_reject" from file /etc/raddb/modules/attr_filter attr_filter attr_filter.access_reject { attrsfile = "/etc/raddb/attrs.access_reject" key = "%{User-Name}" relaxed = no } } # modules } # server server inner-tunnel { # from file /etc/raddb/sites-enabled/inner-tunnel modules { Module: Checking authenticate {...} for more modules to load Module: Checking authorize {...} for more modules to load Module: Checking session {...} for more modules to load Module: Checking post-proxy {...} for more modules to load Module: Checking post-auth {...} for more modules to load } # modules } # server radiusd: #### Opening IP addresses and Ports #### listen { type = "auth" ipaddr = * port = 0 } listen { type = "acct" ipaddr = * port = 0 } listen { type = "control" listen { socket = "/var/run/radiusd/radiusd.sock" } } listen { type = "auth" ipaddr = 127.0.0.1 port = 18120 } ... adding new socket proxy address * port 56269 Listening on authentication address * port 1812 Listening on accounting address * port 1813 Listening on command file /var/run/radiusd/radiusd.sock Listening on authentication address 127.0.0.1 port 18120 as server inner-tunnel Listening on proxy address * port 1814 Ready to process requests. rad_recv: Access-Request packet from host 192.168.2.119 port 1812, id=11, length=100 NAS-IP-Address = 192.168.2.119 NAS-Port = 50017 NAS-Port-Type = Ethernet User-Name = "steve" Calling-Station-Id = "F0-DE-F1-20-C6-3D" Service-Type = Framed-User EAP-Message = 0x02ce000a017374657665 Message-Authenticator = 0xa802ef2a8a207c74b987a437d14bfec3 # Executing section authorize from file /etc/raddb/sites-enabled/default +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop ++[digest] returns noop [suffix] No '@' in User-Name = "steve", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 206 length 10 [eap] No EAP Start, assuming it's an on-going EAP conversation ++[eap] returns updated [files] users: Matched entry steve at line 76 ++[files] returns ok ++[expiration] returns noop ++[logintime] returns noop [pap] WARNING: Auth-Type already set. Not setting to PAP ++[pap] returns noop Found Auth-Type = EAP # Executing group from file /etc/raddb/sites-enabled/default +- entering group authenticate {...} [eap] EAP Identity [eap] processing type tls [tls] Requiring client certificate [tls] Initiate [tls] Start returned 1 ++[eap] returns handled Sending Access-Challenge of id 11 to 192.168.2.119 port 1812 EAP-Message = 0x01cf00060d20 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x24e5fa32242af760fa8fb1e8a324f118 Finished request 0. Going to the next request Waking up in 4.9 seconds. rad_recv: Access-Request packet from host 192.168.2.119 port 1812, id=12, length=202 NAS-IP-Address = 192.168.2.119 NAS-Port = 50017 NAS-Port-Type = Ethernet User-Name = "steve" Calling-Station-Id = "F0-DE-F1-20-C6-3D" Service-Type = Framed-User State = 0x24e5fa32242af760fa8fb1e8a324f118 EAP-Message = 0x02cf005e0d0016030100530100004f03014fe96c1e5a95f9ffae41bacd53fb9213b64e2595 1f0c2a7252fcd4f52bf5c79300002800390038003500160013000a00330032002f0007000500 04001500120009001400110008000600030100 Message-Authenticator = 0xcc735903cd9168219e2b60b44bedb881 # Executing section authorize from file /etc/raddb/sites-enabled/default +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop ++[digest] returns noop [suffix] No '@' in User-Name = "steve", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 207 length 94 [eap] No EAP Start, assuming it's an on-going EAP conversation ++[eap] returns updated [files] users: Matched entry steve at line 76 ++[files] returns ok ++[expiration] returns noop ++[logintime] returns noop [pap] WARNING: Auth-Type already set. Not setting to PAP ++[pap] returns noop Found Auth-Type = EAP # Executing group from file /etc/raddb/sites-enabled/default +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/tls [eap] processing type tls [tls] Authenticate [tls] processing EAP-TLS [tls] eaptls_verify returned 7 [tls] Done initial handshake [tls] (other): before/accept initialization [tls] TLS_accept: before/accept initialization [tls] <<< TLS 1.0 Handshake [length 0053], ClientHello [tls] TLS_accept: SSLv3 read client hello A [tls] >>> TLS 1.0 Handshake [length 002a], ServerHello [tls] TLS_accept: SSLv3 write server hello A [tls] >>> TLS 1.0 Handshake [length 054a], Certificate [tls] TLS_accept: SSLv3 write certificate A [tls] >>> TLS 1.0 Handshake [length 014d], ServerKeyExchange [tls] TLS_accept: SSLv3 write key exchange A [tls] >>> TLS 1.0 Handshake [length 00a7], CertificateRequest [tls] TLS_accept: SSLv3 write certificate request A [tls] TLS_accept: SSLv3 flush data [tls] TLS_accept: Need to read more data: SSLv3 read client certificate A In SSL Handshake Phase In SSL Accept mode [tls] eaptls_process returned 13 ++[eap] returns handled Sending Access-Challenge of id 12 to 192.168.2.119 port 1812 EAP-Message = 0x01d004000dc00000077c160301002a0200002603014fe973361dedff4cc5e6b2cca729a372 41878411a4b105ef552a918a14b6969900003900160301054a0b00054600054300021c308202 18308201c2a003020102020108300d06092a864886f70d0101050500308193310b3009060355 040613024652310f300d060355040813065261646975733112301006035504071309536f6d65 776865726531153013060355040a130c4578616d706c6520496e632e3120301e06092a864886 f70d010901161161646d696e406578616d706c652e636f6d312630240603550403131d457861 6d706c6520436572746966696361746520417574686f72697479 EAP-Message = 0x301e170d3132303631383036333330395a170d3232303432373036333330395a307c310b30 09060355040613024652310f300d0603550408130652616469757331153013060355040a130c 4578616d706c6520496e632e312330210603550403131a4578616d706c652053657276657220 43657274696669636174653120301e06092a864886f70d010901161161646d696e406578616d 706c652e636f6d305c300d06092a864886f70d0101010500034b003048024100bb7ff06cdb39 45ac7fbd8545ccf7b279b761a5772b9f959d9c9885f97008c2a4b88231d6341bc956d5909960 511ffcbd7adddbc38b78b38c2bb5359300b233ef0203010001a3 EAP-Message = 0x17301530130603551d25040c300a06082b06010505070301300d06092a864886f70d010105 050003410062f482f928bbf6f40379a11e2b4a810974aa2a1c1a0172cc5b28ebca870fd312dd 651a1609b821f5476d4b8d0685d2baa81ebaf6ee16bae85c1345f8c4985a8a0003213082031d 308202c7a0030201020209008218224f35e2e485300d06092a864886f70d0101050500308193 310b3009060355040613024652310f300d060355040813065261646975733112301006035504 071309536f6d65776865726531153013060355040a130c4578616d706c6520496e632e312030 1e06092a864886f70d010901161161646d696e406578616d706c EAP-Message = 0x652e636f6d312630240603550403131d4578616d706c652043657274696669636174652041 7574686f72697479301e170d3132303631383036333333315a170d3133303631333036333333 315a308193310b3009060355040613024652310f300d06035504081306526164697573311230 1006035504071309536f6d65776865726531153013060355040a130c4578616d706c6520496e 632e3120301e06092a864886f70d010901161161646d696e406578616d706c652e636f6d3126 30240603550403131d4578616d706c6520436572746966696361746520417574686f72697479 305c300d06092a864886f70d0101010500034b003048024100bf EAP-Message = 0x56ccd33e388350ce4e4fdf78 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x24e5fa322535f760fa8fb1e8a324f118 Finished request 1. Going to the next request Waking up in 4.6 seconds. Cleaning up request 0 ID 11 with timestamp +6 Cleaning up request 1 ID 12 with timestamp +6 WARNING: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! WARNING: !! EAP session for state 0x24e5fa322535f760 did not finish! WARNING: !! Please read http://wiki.freeradius.org/Certificate_Compatibility WARNING: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Ready to process requests. The WPA_supplicant log: …… OpenSSL: SSL_use_PrivateKey_File (PEM) --> OK SSL: Private key loaded successfully CTRL-EVENT-EAP-METHOD EAP vendor 0 method 13 (TLS) selected EAP: EAP entering state METHOD SSL: Received packet(len=6) - Flags 0x20 EAP-TLS: Start SSL: (where=0x10 ret=0x1) SSL: (where=0x1001 ret=0x1) SSL: SSL_connect:before/connect initialization SSL: (where=0x1001 ret=0x1) SSL: SSL_connect:SSLv3 write client hello A SSL: (where=0x1002 ret=0xffffffff) SSL: SSL_connect:error in SSLv3 read server hello A SSL: SSL_connect - want more data SSL: 88 bytes pending from ssl_out SSL: 88 bytes left to be sent out (of total 88 bytes) EAP: method process -> ignore=FALSE methodState=MAY_CONT decision=FAIL EAP: EAP entering state SEND_RESPONSE EAP: EAP entering state IDLE EAPOL: SUPP_BE entering state RESPONSE EAPOL: txSuppRsp TX EAPOL: dst=01:80:c2:00:00:03 TX EAPOL - hexdump(len=98): 01 00 00 5e 02 0d 00 5e 0d 00 16 03 01 00 53 01 00 00 4f 03 01 4f e9 6a bc 62 4d ad 5b 77 af a7 9a d9 b4 10 ab 6e 73 5e 05 1b 1c 8a 09 29 f6 38 aa c9 52 5f 59 00 00 28 00 39 00 38 00 35 00 16 00 13 00 0a 00 33 00 32 00 2f 00 07 00 05 00 04 00 15 00 12 00 09 00 14 00 11 00 08 00 06 00 03 01 00 EAPOL: SUPP_BE entering state RECEIVE RX EAPOL from 00:09:b7:f5:47:d1 RX EAPOL - hexdump(len=46): 01 00 00 04 04 0d 00 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 EAPOL: Received EAP-Packet frame EAPOL: SUPP_BE entering state REQUEST EAPOL: getSuppRsp EAP: EAP entering state RECEIVED EAP: Received EAP-Failure EAP: EAP entering state FAILURE CTRL-EVENT-EAP-FAILURE EAP authentication failed EAPOL: SUPP_PAE entering state HELD EAPOL: Supplicant port status: Unauthorized EAPOL: SUPP_BE entering state RECEIVE EAPOL: SUPP_BE entering state FAIL EAPOL: SUPP_BE entering state IDLE EAPOL authentication completed unsuccessfully EAPOL: startWhen --> 0 EAPOL: authWhile --> 0 EAPOL: idleWhile --> 0 EAPOL: heldWhile --> 0 EAPOL: disable timer tick EAPOL: SUPP_PAE entering state CONNECTING EAPOL: enable timer tick EAPOL: SUPP_PAE entering state AUTHENTICATING EAPOL: SUPP_BE entering state FAIL EAPOL: SUPP_PAE entering state HELD EAPOL: Supplicant port status: Unauthorized EAPOL: SUPP_BE entering state IDLE EAPOL authentication completed unsuccessfully RX EAPOL from 00:09:b7:f5:47:d1 RX EAPOL - hexdump(len=46): 01 00 00 04 04 0e 00 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 EAPOL: Received EAP-Packet frame EAPOL: SUPP_PAE entering state RESTART EAP: EAP entering state INITIALIZE EAP: deinitialize previously used EAP method (13, TLS) at INITIALIZE EAP: EAP entering state IDLE EAPOL: SUPP_PAE entering state AUTHENTICATING EAPOL: SUPP_BE entering state REQUEST EAPOL: getSuppRsp EAP: EAP entering state RECEIVED EAP: Received EAP-Failure EAP: EAP-Success Id mismatch - reqId=14 lastId=-1 EAP: EAP entering state DISCARD EAP: EAP entering state IDLE EAPOL: SUPP_BE entering state RECEIVE RX EAPOL from 00:09:b7:f5:47:d1 RX EAPOL - hexdump(len=46): 01 00 00 05 01 0f 00 05 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 EAPOL: Received EAP-Packet frame EAPOL: SUPP_BE entering state REQUEST EAPOL: getSuppRsp EAP: EAP entering state RECEIVED EAP: Received EAP-Request id=15 method=1 vendor=0 vendorMethod=0 EAP: EAP entering state IDENTITY CTRL-EVENT-EAP-STARTED EAP authentication started EAP: EAP-Request Identity data - hexdump_ascii(len=0): EAP: using real identity - hexdump_ascii(len=5): 73 74 65 76 65 steve EAP: EAP entering state SEND_RESPONSE EAP: EAP entering state IDLE EAPOL: SUPP_BE entering state RESPONSE EAPOL: txSuppRsp TX EAPOL: dst=01:80:c2:00:00:03 TX EAPOL - hexdump(len=14): 01 00 00 0a 02 0f 00 0a 01 73 74 65 76 65 EAPOL: SUPP_BE entering state RECEIVE RX EAPOL from 00:09:b7:f5:47:d1 RX EAPOL - hexdump(len=46): 01 00 00 06 01 10 00 06 0d 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 EAPOL: Received EAP-Packet frame EAPOL: SUPP_BE entering state REQUEST EAPOL: getSuppRsp EAP: EAP entering state RECEIVED EAP: Received EAP-Request id=16 method=13 vendor=0 vendorMethod=0 EAP: EAP entering state GET_METHOD CTRL-EVENT-EAP-PROPOSED-METHOD vendor=0 method=13 EAP: Initialize selected EAP method: vendor 0 method 13 (TLS) TLS: using phase1 config options TLS: Trusted root certificate(s) loaded OpenSSL: tls_connection_client_cert - SSL_use_certificate_file (DER) failed error:0D0680A8:asn1 encoding routines:ASN1_CHECK_TLEN:wrong tag OpenSSL: pending error: error:0D07803A:asn1 encoding routines:ASN1_ITEM_EX_D2I:nested asn1 error OpenSSL: pending error: error:140C800D:SSL routines:SSL_use_certificate_file:ASN1 lib OpenSSL: SSL_use_certificate_file (PEM) --> OK OpenSSL: tls_connection_private_key - SSL_use_PrivateKey_File (DER) failed error:0D094068:asn1 encoding routines:d2i_ASN1_SET:bad tag OpenSSL: pending error: error:0D0680A8:asn1 encoding routines:ASN1_CHECK_TLEN:wrong tag OpenSSL: pending error: error:0D07803A:asn1 encoding routines:ASN1_ITEM_EX_D2I:nested asn1 error OpenSSL: pending error: error:0D09A00D:asn1 encoding routines:d2i_PrivateKey:ASN1 lib OpenSSL: pending error: error:140CB00D:SSL routines:SSL_use_PrivateKey_file:ASN1 lib OpenSSL: SSL_use_PrivateKey_File (PEM) --> OK SSL: Private key loaded successfully CTRL-EVENT-EAP-METHOD EAP vendor 0 method 13 (TLS) selected EAP: EAP entering state METHOD SSL: Received packet(len=6) - Flags 0x20 EAP-TLS: Start SSL: (where=0x10 ret=0x1) SSL: (where=0x1001 ret=0x1) SSL: SSL_connect:before/connect initialization SSL: (where=0x1001 ret=0x1) SSL: SSL_connect:SSLv3 write client hello A SSL: (where=0x1002 ret=0xffffffff) SSL: SSL_connect:error in SSLv3 read server hello A SSL: SSL_connect - want more data SSL: 88 bytes pending from ssl_out SSL: 88 bytes left to be sent out (of total 88 bytes) EAP: method process -> ignore=FALSE methodState=MAY_CONT decision=FAIL EAP: EAP entering state SEND_RESPONSE EAP: EAP entering state IDLE EAPOL: SUPP_BE entering state RESPONSE EAPOL: txSuppRsp TX EAPOL: dst=01:80:c2:00:00:03 TX EAPOL - hexdump(len=98): 01 00 00 5e 02 10 00 5e 0d 00 16 03 01 00 53 01 00 00 4f 03 01 4f e9 6a f9 99 22 ae 19 c9 55 85 82 e4 cb 9d 95 e2 1b 9b 99 f4 13 d2 6c 8c 9d 48 5e ac 51 53 1f 00 00 28 00 39 00 38 00 35 00 16 00 13 00 0a 00 33 00 32 00 2f 00 07 00 05 00 04 00 15 00 12 00 09 00 14 00 11 00 08 00 06 00 03 01 00 EAPOL: SUPP_BE entering state RECEIVE EAPOL: startWhen --> 0 RX EAPOL from 00:09:b7:f5:47:d1 RX EAPOL - hexdump(len=46): 01 00 00 04 04 10 00 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 EAPOL: Received EAP-Packet frame EAPOL: SUPP_BE entering state REQUEST EAPOL: getSuppRsp EAP: EAP entering state RECEIVED EAP: Received EAP-Failure EAP: EAP entering state FAILURE CTRL-EVENT-EAP-FAILURE EAP authentication failed EAPOL: SUPP_PAE entering state HELD EAPOL: Supplicant port status: Unauthorized EAPOL: SUPP_BE entering state RECEIVE EAPOL: SUPP_BE entering state FAIL EAPOL: SUPP_BE entering state IDLE EAPOL authentication completed unsuccessfully CTRL-EVENT-TERMINATING - signal 0 received Removing interface {5B7842B2-12D2-4B22-8600-4AA17EFCD322} NDIS: Set OID 0d010102 - hexdump(len=36): [REMOVED] ndis_set_oid: oid=0xd010102 len (36) failed No keys have been configured - skip key clearing State: ASSOCIATED -> DISCONNECTED EAPOL: External notification - portEnabled=0 EAPOL: SUPP_PAE entering state DISCONNECTED EAPOL: Supplicant port status: Unauthorized EAPOL: SUPP_BE entering state INITIALIZE EAP: EAP entering state DISABLED EAPOL: Supplicant port status: Unauthorized EAPOL: External notification - portValid=0 EAPOL: Supplicant port status: Unauthorized No keys have been configured - skip key clearing EAP: deinitialize previously used EAP method (13, TLS) at EAP deinit Cancelling scan request Cancelling authentication timeout ndis_events: terminated NDIS: Set OID 0d010102 - hexdump(len=36): [REMOVED] ndis_set_oid: oid=0xd010102 len (36) failed NDIS: Set OID 0d010115 - hexdump(len=4): [REMOVED] ndis_set_oid: oid=0xd010115 len (4) failed NDIS: failed to disassociate and turn radio off CTRL: close pipe 005E3258 Thank you!

2 1

Question on Cisco-AVPair = "device-traffic-class=voice"
by John 23 Jun '12

23 Jun '12

Hi, Is there a way that freeradius can tell it is a VOICE device? Like ACS server: Cisco-AVPair = "device-traffic-class=voice". Here is a link to IP Telephony In IEEE 802.1X ... http://www.cisco.com/en/US/prod/collateral/iosswrel/ps6537/ps6586/ps6638/co… Thanks a lot, Hangjun

2 3

Adding domain names to user logins
by Kriston 23 Jun '12

23 Jun '12

I have many domain names but my users log in with just their usernames. How do I append the correct domainname to it? In FreeRadius 1.x I used "%{User-Name}%{atdomain:%n}" but what's the equivalent in FreeRadius 2.x?. Thank you, Kriston

2 4

radwho
by Luo, Frank Y.F. Mr. 23 Jun '12

23 Jun '12

I have noticed that radwho command only return one entry at any time but obviously there are more than one people logged in $ sudo radwho Login Name What TTY When From Location d0c1b122dc d0c1b122dc75 shell S29 Fri 11:43 172.18.47.242 172.24.192.42 Any hint? Thanks Frank

2 1

Re: Can't figure out Group Authentication
by Alan Buxey 22 Jun '12

22 Jun '12

You've got to set up some group checking...you haven't, so ldap-group means nothing to the server so you hit the default reject that you added... alan

3 3

Re: Reg: Accept the user without Mysql check.
by Fajar A. Nugraha 22 Jun '12

22 Jun '12

Please keep cc to the list. On Fri, Jun 22, 2012 at 9:45 PM, Malla reddy Sama <mallareddy.sama(a)yahoo.com> wrote: > Dear Fajar, > > I am facing a problem like below. please help where I am doing mistake. > > Ignoring request to authentication address * port 1812 from unknown client > 172.20.68.97 port 59268 Let's find out what's wrong from the debug log. > ******************** Clients.conf ************* > > > client 172.20.68.0/24 { //ip of server > secret=secret > } > at a glance that looks correct ... > radiusd: #### Loading Clients #### > client localhost { > ipaddr = 127.0.0.1 > require_message_authenticator = no > secret = "secret" > nastype = "other" > } > client 170.20.68.0/24 { > require_message_authenticator = no > secret = "secret" > } ... but that's not what the debug log says. Notice the difference, 170 instead of 172? Did you edit the debug log? Or perhaps you edited the wrong copy of configuration files? Either way, you can see which files the server parses by looking at the debug log. You can also see what the server thinks the configuration values are, which might different from what you think they should be. Notice how easy that was to debug problems when you provide the complete debug log? And PS, if you have a different problem, better start a new thread with a new subject. It will be easier for others to follow. Also please always cc the list, so others with the same problem can benefit as well. -- Fajar

3 2

Upgrade or migration away from VMPS - what are my options?
by Kaya Saman 22 Jun '12

22 Jun '12

Hi, since I've been having issues with the latest Cisco OS (version 15) and VMPS not connecting properly what are my alternatives? Sure I can stay on version 12.x if need be however, if we purchase some new kit that **only** comes with version 15 I will have the same issue as previously had with IP phones not registering etc.... I have been Google'ing a bit to attempt try to understand the difference as I was told that VMPS was a subset of FreeRADIUS; the only thing is that I'm quite new to this and just need some advice and/or to be pointed in the right direction as of to what material to start reading - additionally what I should be looking for. So really to summarize, since VMPS is old and I have been told to move away from it which system should I be looking at to automate vlan distribution throughout the network and is there any chance of using the already built MySQL VMPS database?? Regards, Kaya

4 13