June 2019 - Freeradius-Users - lists.freeradius.org

Strange behaviour after AD password reset
by Richard Letuma 14 Jun '19

14 Jun '19

Hi, Could you please advise me what could be the issue here. These are the steps that I followed: 1) I have set "winbind offline logon = no" in /etc/samba/smb.conf under global 2) I have set /etc/raddb/mods-enabled/eap to "enable = no" in cache section. It is default behaviour. I just set it to be 100% sure that it is set. 3) Then I restarted smb and nmb with systemctl status smb nmb 4) Also I have restarted the radiusd 5) I then reset a password from AD and use radtest and wbinfo to test The problem is that after password reset OLD and NEW password works with radtest (also with eapol_test). After AD password reset if I type "radtest -t mschap myuserid PasswordOLD <IP Address> 0 testing123" and I type "radtest radtest -t mschap myuserid PasswordNEW <IP Address> 0 testing123" they both work. After approximately 5 minutes, the "radtest -t mschap myuserid PasswordOLD <IP Address> 0 testing123" will stop working and authentication fail. This is what I expect. The new password will remain working even. *Why is the old password works for approximately 5 minutes with radtest? I have also checked with eapol_test and the old password still works for 5 minutes before failing ( i.e Access-Reject ).* *The command "wbinfo -a <DOMAN USER and password>" immediately reflects that the password was changed. With "wbinfo -a", I do not have a problem where an old password work for 5 minutes.* In /etc/raddb/mods-enabled/ntlm_auth is there a possibility of using strictly wbinfo instead of ntlm_auth? I am on samba 4.8.3 and it is running on latest Centos 7. Please advise. Thank you.

2 1

Google Secure LDAP
by eko＠flyingtongue.io 13 Jun '19

13 Jun '19

I'm attempting to use Google Secure LDAP solution for authentication and authorization. I'm not able to use this with a supplicant such as a laptop/phone, radtest is working fine which leads me to believe it's an issue of the password being hashed by mschap. I understand from reading previous threads that I need to use EAP-TTLS-PAP or PEAP-GTC. How can I get freeradius to work with Google Secure LDAP? When freeradius does do an ldap bind which user attribute is it looking for? I think userPassword but in this case I don't think it exists. Full debug: FreeRADIUS Version 3.0.12 Copyright (C) 1999-2016 The FreeRADIUS server project and contributors There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE You may redistribute copies of FreeRADIUS under the terms of the GNU General Public License For more information about these matters, see the file named COPYRIGHT Starting - reading configuration files ... including dictionary file /usr/share/freeradius/dictionary including dictionary file /usr/share/freeradius/dictionary.dhcp including dictionary file /usr/share/freeradius/dictionary.vqp including dictionary file /etc/freeradius/3.0/dictionary including configuration file /etc/freeradius/3.0/radiusd.conf including configuration file /etc/freeradius/3.0/proxy.conf including configuration file /etc/freeradius/3.0/clients.conf including files in directory /etc/freeradius/3.0/mods-enabled/ including configuration file /etc/freeradius/3.0/mods-enabled/cache_eap including configuration file /etc/freeradius/3.0/mods-enabled/linelog including configuration file /etc/freeradius/3.0/mods-enabled/sradutmp including configuration file /etc/freeradius/3.0/mods-enabled/exec including configuration file /etc/freeradius/3.0/mods-enabled/detail including configuration file /etc/freeradius/3.0/mods-enabled/realm including configuration file /etc/freeradius/3.0/mods-enabled/chap including configuration file /etc/freeradius/3.0/mods-enabled/soh including configuration file /etc/freeradius/3.0/mods-enabled/preprocess including configuration file /etc/freeradius/3.0/mods-enabled/always including configuration file /etc/freeradius/3.0/mods-enabled/digest including configuration file /etc/freeradius/3.0/mods-enabled/attr_filter including configuration file /etc/freeradius/3.0/mods-enabled/unpack including configuration file /etc/freeradius/3.0/mods-enabled/logintime including configuration file /etc/freeradius/3.0/mods-enabled/pap including configuration file /etc/freeradius/3.0/mods-enabled/ldap including configuration file /etc/freeradius/3.0/mods-enabled/ntlm_auth including configuration file /etc/freeradius/3.0/mods-enabled/echo including configuration file /etc/freeradius/3.0/mods-enabled/files including configuration file /etc/freeradius/3.0/mods-enabled/unix including configuration file /etc/freeradius/3.0/mods-enabled/expiration including configuration file /etc/freeradius/3.0/mods-enabled/utf8 including configuration file /etc/freeradius/3.0/mods-enabled/dynamic_clients including configuration file /etc/freeradius/3.0/mods-enabled/expr including configuration file /etc/freeradius/3.0/mods-enabled/detail.log including configuration file /etc/freeradius/3.0/mods-enabled/eap including configuration file /etc/freeradius/3.0/mods-enabled/replicate including configuration file /etc/freeradius/3.0/mods-enabled/mschap including configuration file /etc/freeradius/3.0/mods-enabled/radutmp including configuration file /etc/freeradius/3.0/mods-enabled/passwd including files in directory /etc/freeradius/3.0/policy.d/ including configuration file /etc/freeradius/3.0/policy.d/moonshot-targeted-ids including configuration file /etc/freeradius/3.0/policy.d/accounting including configuration file /etc/freeradius/3.0/policy.d/debug including configuration file /etc/freeradius/3.0/policy.d/cui including configuration file /etc/freeradius/3.0/policy.d/canonicalization including configuration file /etc/freeradius/3.0/policy.d/eap including configuration file /etc/freeradius/3.0/policy.d/filter including configuration file /etc/freeradius/3.0/policy.d/abfab-tr including configuration file /etc/freeradius/3.0/policy.d/operator-name including configuration file /etc/freeradius/3.0/policy.d/dhcp including configuration file /etc/freeradius/3.0/policy.d/control including files in directory /etc/freeradius/3.0/sites-enabled/ including configuration file /etc/freeradius/3.0/sites-enabled/inner-tunnel including configuration file /etc/freeradius/3.0/sites-enabled/default main { security { user = "freerad" group = "freerad" allow_core_dumps = no } name = "freeradius" prefix = "/usr" localstatedir = "/var" logdir = "/var/log/freeradius" run_dir = "/var/run/freeradius" } main { name = "freeradius" prefix = "/usr" localstatedir = "/var" sbindir = "/usr/sbin" logdir = "/var/log/freeradius" run_dir = "/var/run/freeradius" libdir = "/usr/lib/freeradius" radacctdir = "/var/log/freeradius/radacct" hostname_lookups = no max_request_time = 30 cleanup_delay = 5 max_requests = 16384 pidfile = "/var/run/freeradius/freeradius.pid" checkrad = "/usr/sbin/checkrad" debug_level = 0 proxy_requests = yes log { stripped_names = no auth = no auth_badpass = no auth_goodpass = no colourise = yes msg_denied = "You are already logged in - access denied" } resources { } security { max_attributes = 200 reject_delay = 1.000000 status_server = yes } } radiusd: #### Loading Realms and Home Servers #### proxy server { retry_delay = 5 retry_count = 3 default_fallback = no dead_time = 120 wake_all_if_all_dead = no } home_server localhost { ipaddr = 127.0.0.1 port = 1812 type = "auth" secret = <<< secret >>> response_window = 20.000000 response_timeouts = 1 max_outstanding = 65536 zombie_period = 40 status_check = "status-server" ping_interval = 30 check_interval = 30 check_timeout = 4 num_answers_to_alive = 3 revive_interval = 120 limit { max_connections = 16 max_requests = 0 lifetime = 0 idle_timeout = 0 } coa { irt = 2 mrt = 16 mrc = 5 mrd = 30 } } home_server_pool my_auth_failover { type = fail-over home_server = localhost } realm example.com { auth_pool = my_auth_failover } realm LOCAL { } radiusd: #### Loading Clients #### client localhost { ipaddr = 127.0.0.1 require_message_authenticator = no secret = <<< secret >>> nas_type = "other" proto = "*" limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } client localhost_ipv6 { ipv6addr = ::1 require_message_authenticator = no secret = <<< secret >>> limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } client sz { ipaddr = 10.0.32.55 require_message_authenticator = no secret = <<< secret >>> limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } client wap1 { ipaddr = 10.1.25.208 require_message_authenticator = no secret = <<< secret >>> shortname = "name" limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } Debugger not attached # Creating Auth-Type = ldap # Creating Auth-Type = mschap # Creating Auth-Type = eap # Creating Auth-Type = PAP # Creating Auth-Type = CHAP # Creating Auth-Type = MS-CHAP # Creating Auth-Type = digest radiusd: #### Instantiating modules #### modules { # Loaded module rlm_cache # Loading module "cache_eap" from file /etc/freeradius/3.0/mods-enabled/cache_eap cache cache_eap { driver = "rlm_cache_rbtree" key = "%{%{control:State}:-%{%{reply:State}:-%{State}}}" ttl = 15 max_entries = 0 epoch = 0 add_stats = no } # Loaded module rlm_linelog # Loading module "linelog" from file /etc/freeradius/3.0/mods-enabled/linelog linelog { filename = "/var/log/freeradius/linelog" escape_filenames = no syslog_severity = "info" permissions = 384 format = "This is a log message for %{User-Name}" reference = "messages.%{%{reply:Packet-Type}:-default}" } # Loading module "log_accounting" from file /etc/freeradius/3.0/mods-enabled/linelog linelog log_accounting { filename = "/var/log/freeradius/linelog-accounting" escape_filenames = no syslog_severity = "info" permissions = 384 format = "" reference = "Accounting-Request.%{%{Acct-Status-Type}:-unknown}" } # Loaded module rlm_radutmp # Loading module "sradutmp" from file /etc/freeradius/3.0/mods-enabled/sradutmp radutmp sradutmp { filename = "/var/log/freeradius/sradutmp" username = "%{User-Name}" case_sensitive = yes check_with_nas = yes permissions = 420 caller_id = no } # Loaded module rlm_exec # Loading module "exec" from file /etc/freeradius/3.0/mods-enabled/exec exec { wait = no input_pairs = "request" shell_escape = yes timeout = 10 } # Loaded module rlm_detail # Loading module "detail" from file /etc/freeradius/3.0/mods-enabled/detail detail { filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loaded module rlm_realm # Loading module "IPASS" from file /etc/freeradius/3.0/mods-enabled/realm realm IPASS { format = "prefix" delimiter = "/" ignore_default = no ignore_null = no } # Loading module "suffix" from file /etc/freeradius/3.0/mods-enabled/realm realm suffix { format = "suffix" delimiter = "@" ignore_default = no ignore_null = no } # Loading module "realmpercent" from file /etc/freeradius/3.0/mods-enabled/realm realm realmpercent { format = "suffix" delimiter = "%" ignore_default = no ignore_null = no } # Loading module "ntdomain" from file /etc/freeradius/3.0/mods-enabled/realm realm ntdomain { format = "prefix" delimiter = "\\" ignore_default = no ignore_null = no } # Loaded module rlm_chap # Loading module "chap" from file /etc/freeradius/3.0/mods-enabled/chap # Loaded module rlm_soh # Loading module "soh" from file /etc/freeradius/3.0/mods-enabled/soh soh { dhcp = yes } # Loaded module rlm_preprocess # Loading module "preprocess" from file /etc/freeradius/3.0/mods-enabled/preprocess preprocess { huntgroups = "/etc/freeradius/3.0/mods-config/preprocess/huntgroups" hints = "/etc/freeradius/3.0/mods-config/preprocess/hints" with_ascend_hack = no ascend_channels_per_line = 23 with_ntdomain_hack = no with_specialix_jetstream_hack = no with_cisco_vsa_hack = no with_alvarion_vsa_hack = no } # Loaded module rlm_always # Loading module "reject" from file /etc/freeradius/3.0/mods-enabled/always always reject { rcode = "reject" simulcount = 0 mpp = no } # Loading module "fail" from file /etc/freeradius/3.0/mods-enabled/always always fail { rcode = "fail" simulcount = 0 mpp = no } # Loading module "ok" from file /etc/freeradius/3.0/mods-enabled/always always ok { rcode = "ok" simulcount = 0 mpp = no } # Loading module "handled" from file /etc/freeradius/3.0/mods-enabled/always always handled { rcode = "handled" simulcount = 0 mpp = no } # Loading module "invalid" from file /etc/freeradius/3.0/mods-enabled/always always invalid { rcode = "invalid" simulcount = 0 mpp = no } # Loading module "userlock" from file /etc/freeradius/3.0/mods-enabled/always always userlock { rcode = "userlock" simulcount = 0 mpp = no } # Loading module "notfound" from file /etc/freeradius/3.0/mods-enabled/always always notfound { rcode = "notfound" simulcount = 0 mpp = no } # Loading module "noop" from file /etc/freeradius/3.0/mods-enabled/always always noop { rcode = "noop" simulcount = 0 mpp = no } # Loading module "updated" from file /etc/freeradius/3.0/mods-enabled/always always updated { rcode = "updated" simulcount = 0 mpp = no } # Loaded module rlm_digest # Loading module "digest" from file /etc/freeradius/3.0/mods-enabled/digest # Loaded module rlm_attr_filter # Loading module "attr_filter.post-proxy" from file /etc/freeradius/3.0/mods-enabled/attr_filter attr_filter attr_filter.post-proxy { filename = "/etc/freeradius/3.0/mods-config/attr_filter/post-proxy" key = "%{Realm}" relaxed = no } # Loading module "attr_filter.pre-proxy" from file /etc/freeradius/3.0/mods-enabled/attr_filter attr_filter attr_filter.pre-proxy { filename = "/etc/freeradius/3.0/mods-config/attr_filter/pre-proxy" key = "%{Realm}" relaxed = no } # Loading module "attr_filter.access_reject" from file /etc/freeradius/3.0/mods-enabled/attr_filter attr_filter attr_filter.access_reject { filename = "/etc/freeradius/3.0/mods-config/attr_filter/access_reject" key = "%{User-Name}" relaxed = no } # Loading module "attr_filter.access_challenge" from file /etc/freeradius/3.0/mods-enabled/attr_filter attr_filter attr_filter.access_challenge { filename = "/etc/freeradius/3.0/mods-config/attr_filter/access_challenge" key = "%{User-Name}" relaxed = no } # Loading module "attr_filter.accounting_response" from file /etc/freeradius/3.0/mods-enabled/attr_filter attr_filter attr_filter.accounting_response { filename = "/etc/freeradius/3.0/mods-config/attr_filter/accounting_response" key = "%{User-Name}" relaxed = no } # Loaded module rlm_unpack # Loading module "unpack" from file /etc/freeradius/3.0/mods-enabled/unpack # Loaded module rlm_logintime # Loading module "logintime" from file /etc/freeradius/3.0/mods-enabled/logintime logintime { minimum_timeout = 60 } # Loaded module rlm_pap # Loading module "pap" from file /etc/freeradius/3.0/mods-enabled/pap pap { normalise = yes } # Loaded module rlm_ldap # Loading module "ldap" from file /etc/freeradius/3.0/mods-enabled/ldap ldap { server = "ldaps://ldap.google.com:636" identity = "SomethingCrazy" password = <<< secret >>> sasl { } user { scope = "sub" access_positive = yes sasl { } } group { filter = "(objectClass=posixGroup)" scope = "sub" name_attribute = "cn" membership_attribute = "memberOf" cacheable_name = no cacheable_dn = no } client { filter = "(objectClass=radiusClient)" scope = "sub" base_dn = "dc=burro,dc=org" } profile { } options { ldap_debug = 40 chase_referrals = yes rebind = yes net_timeout = 1 res_timeout = 10 srv_timelimit = 3 idle = 60 probes = 3 interval = 3 } tls { certificate_file = "/etc/freeradius/3.0/certs/ldap-client.crt" private_key_file = "/etc/freeradius/3.0/certs/ldap-client.key" start_tls = no require_cert = "allow" } } Creating attribute LDAP-Group # Loading module "ntlm_auth" from file /etc/freeradius/3.0/mods-enabled/ntlm_auth exec ntlm_auth { wait = yes program = "/path/to/ntlm_auth --request-nt-key --domain=MYDOMAIN --username=%{mschap:User-Name} --password=%{User-Password}" shell_escape = yes } # Loading module "echo" from file /etc/freeradius/3.0/mods-enabled/echo exec echo { wait = yes program = "/bin/echo %{User-Name}" input_pairs = "request" output_pairs = "reply" shell_escape = yes } # Loaded module rlm_files # Loading module "files" from file /etc/freeradius/3.0/mods-enabled/files files { filename = "/etc/freeradius/3.0/mods-config/files/authorize" acctusersfile = "/etc/freeradius/3.0/mods-config/files/accounting" preproxy_usersfile = "/etc/freeradius/3.0/mods-config/files/pre-proxy" } # Loaded module rlm_unix # Loading module "unix" from file /etc/freeradius/3.0/mods-enabled/unix unix { radwtmp = "/var/log/freeradius/radwtmp" } Creating attribute Unix-Group # Loaded module rlm_expiration # Loading module "expiration" from file /etc/freeradius/3.0/mods-enabled/expiration # Loaded module rlm_utf8 # Loading module "utf8" from file /etc/freeradius/3.0/mods-enabled/utf8 # Loaded module rlm_dynamic_clients # Loading module "dynamic_clients" from file /etc/freeradius/3.0/mods-enabled/dynamic_clients # Loaded module rlm_expr # Loading module "expr" from file /etc/freeradius/3.0/mods-enabled/expr expr { safe_characters = "@abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789.-_: /äéöüàâæçèéêëîïôœùûüaÿÄÉÖÜßÀÂÆÇÈÉÊËÎÏÔŒÙÛÜŸ" } # Loading module "auth_log" from file /etc/freeradius/3.0/mods-enabled/detail.log detail auth_log { filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loading module "reply_log" from file /etc/freeradius/3.0/mods-enabled/detail.log detail reply_log { filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/reply-detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loading module "pre_proxy_log" from file /etc/freeradius/3.0/mods-enabled/detail.log detail pre_proxy_log { filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/pre-proxy-detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loading module "post_proxy_log" from file /etc/freeradius/3.0/mods-enabled/detail.log detail post_proxy_log { filename = "/var/log/freeradius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/post-proxy-detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loaded module rlm_eap # Loading module "eap" from file /etc/freeradius/3.0/mods-enabled/eap eap { default_eap_type = "md5" timer_expire = 60 ignore_unknown_eap_types = no cisco_accounting_username_bug = no max_sessions = 16384 } # Loaded module rlm_replicate # Loading module "replicate" from file /etc/freeradius/3.0/mods-enabled/replicate # Loaded module rlm_mschap # Loading module "mschap" from file /etc/freeradius/3.0/mods-enabled/mschap mschap { use_mppe = yes require_encryption = no require_strong = no with_ntdomain_hack = yes passchange { } allow_retry = yes } # Loading module "radutmp" from file /etc/freeradius/3.0/mods-enabled/radutmp radutmp { filename = "/var/log/freeradius/radutmp" username = "%{User-Name}" case_sensitive = yes check_with_nas = yes permissions = 384 caller_id = yes } # Loaded module rlm_passwd # Loading module "etc_passwd" from file /etc/freeradius/3.0/mods-enabled/passwd passwd etc_passwd { filename = "/etc/passwd" format = "*User-Name:Crypt-Password:" delimiter = ":" ignore_nislike = no ignore_empty = yes allow_multiple_keys = no hash_size = 100 } instantiate { } # Instantiating module "cache_eap" from file /etc/freeradius/3.0/mods-enabled/cache_eap rlm_cache (cache_eap): Driver rlm_cache_rbtree (module rlm_cache_rbtree) loaded and linked # Instantiating module "linelog" from file /etc/freeradius/3.0/mods-enabled/linelog # Instantiating module "log_accounting" from file /etc/freeradius/3.0/mods-enabled/linelog # Instantiating module "detail" from file /etc/freeradius/3.0/mods-enabled/detail # Instantiating module "IPASS" from file /etc/freeradius/3.0/mods-enabled/realm # Instantiating module "suffix" from file /etc/freeradius/3.0/mods-enabled/realm # Instantiating module "realmpercent" from file /etc/freeradius/3.0/mods-enabled/realm # Instantiating module "ntdomain" from file /etc/freeradius/3.0/mods-enabled/realm # Instantiating module "preprocess" from file /etc/freeradius/3.0/mods-enabled/preprocess reading pairlist file /etc/freeradius/3.0/mods-config/preprocess/huntgroups reading pairlist file /etc/freeradius/3.0/mods-config/preprocess/hints # Instantiating module "reject" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "fail" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "ok" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "handled" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "invalid" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "userlock" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "notfound" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "noop" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "updated" from file /etc/freeradius/3.0/mods-enabled/always # Instantiating module "attr_filter.post-proxy" from file /etc/freeradius/3.0/mods-enabled/attr_filter reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/post-proxy # Instantiating module "attr_filter.pre-proxy" from file /etc/freeradius/3.0/mods-enabled/attr_filter reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/pre-proxy # Instantiating module "attr_filter.access_reject" from file /etc/freeradius/3.0/mods-enabled/attr_filter reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/access_reject [/etc/freeradius/3.0/mods-config/attr_filter/access_reject]:11 Check item "FreeRADIUS-Response-Delay" found in filter list for realm "DEFAULT". [/etc/freeradius/3.0/mods-config/attr_filter/access_reject]:11 Check item "FreeRADIUS-Response-Delay-USec" found in filter list for realm "DEFAULT". # Instantiating module "attr_filter.access_challenge" from file /etc/freeradius/3.0/mods-enabled/attr_filter reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/access_challenge # Instantiating module "attr_filter.accounting_response" from file /etc/freeradius/3.0/mods-enabled/attr_filter reading pairlist file /etc/freeradius/3.0/mods-config/attr_filter/accounting_response # Instantiating module "logintime" from file /etc/freeradius/3.0/mods-enabled/logintime # Instantiating module "pap" from file /etc/freeradius/3.0/mods-enabled/pap # Instantiating module "ldap" from file /etc/freeradius/3.0/mods-enabled/ldap rlm_ldap: libldap vendor: OpenLDAP, version: 20444 accounting { reference = "%{tolower:type.%{Acct-Status-Type}}" } post-auth { reference = "." } rlm_ldap (ldap): Initialising connection pool pool { start = 5 min = 3 max = 32 spare = 10 uses = 0 lifetime = 0 cleanup_interval = 30 idle_timeout = 60 retry_delay = 30 spread = no } rlm_ldap (ldap): Opening additional connection (0), 1 of 32 pending slots used rlm_ldap (ldap): Connecting to ldaps://ldap.google.com:636 rlm_ldap (ldap): Waiting for bind result... rlm_ldap (ldap): Bind successful rlm_ldap (ldap): Opening additional connection (1), 1 of 31 pending slots used rlm_ldap (ldap): Connecting to ldaps://ldap.google.com:636 rlm_ldap (ldap): Waiting for bind result... rlm_ldap (ldap): Bind successful rlm_ldap (ldap): Opening additional connection (2), 1 of 30 pending slots used rlm_ldap (ldap): Connecting to ldaps://ldap.google.com:636 rlm_ldap (ldap): Waiting for bind result... rlm_ldap (ldap): Bind successful rlm_ldap (ldap): Opening additional connection (3), 1 of 29 pending slots used rlm_ldap (ldap): Connecting to ldaps://ldap.google.com:636 rlm_ldap (ldap): Waiting for bind result... rlm_ldap (ldap): Bind successful rlm_ldap (ldap): Opening additional connection (4), 1 of 28 pending slots used rlm_ldap (ldap): Connecting to ldaps://ldap.google.com:636 rlm_ldap (ldap): Waiting for bind result... rlm_ldap (ldap): Bind successful # Instantiating module "files" from file /etc/freeradius/3.0/mods-enabled/files reading pairlist file /etc/freeradius/3.0/mods-config/files/authorize reading pairlist file /etc/freeradius/3.0/mods-config/files/accounting reading pairlist file /etc/freeradius/3.0/mods-config/files/pre-proxy # Instantiating module "expiration" from file /etc/freeradius/3.0/mods-enabled/expiration # Instantiating module "auth_log" from file /etc/freeradius/3.0/mods-enabled/detail.log rlm_detail (auth_log): 'User-Password' suppressed, will not appear in detail output # Instantiating module "reply_log" from file /etc/freeradius/3.0/mods-enabled/detail.log # Instantiating module "pre_proxy_log" from file /etc/freeradius/3.0/mods-enabled/detail.log # Instantiating module "post_proxy_log" from file /etc/freeradius/3.0/mods-enabled/detail.log # Instantiating module "eap" from file /etc/freeradius/3.0/mods-enabled/eap # Linked to sub-module rlm_eap_md5 # Linked to sub-module rlm_eap_leap # Linked to sub-module rlm_eap_gtc gtc { challenge = "Password: " auth_type = "PAP" } # Linked to sub-module rlm_eap_tls tls { tls = "tls-common" } tls-config tls-common { verify_depth = 0 ca_path = "/etc/freeradius/3.0/certs" pem_file_type = yes private_key_file = "/etc/ssl/private/ssl-cert-snakeoil.key" certificate_file = "/etc/ssl/certs/ssl-cert-snakeoil.pem" ca_file = "/etc/ssl/certs/ca-certificates.crt" private_key_password = <<< secret >>> dh_file = "/etc/freeradius/3.0/certs/dh" fragment_size = 1024 include_length = yes auto_chain = yes check_crl = no check_all_crl = no cipher_list = "DEFAULT" ecdh_curve = "prime256v1" cache { enable = yes lifetime = 24 max_entries = 255 } verify { skip_if_ocsp_ok = no } ocsp { enable = no override_cert_url = yes url = "http://127.0.0.1/ocsp/" use_nonce = yes timeout = 0 softfail = no } } # Linked to sub-module rlm_eap_ttls ttls { tls = "tls-common" default_eap_type = "md5" copy_request_to_tunnel = no use_tunneled_reply = no virtual_server = "inner-tunnel" include_length = yes require_client_cert = no } tls: Using cached TLS configuration from previous invocation # Linked to sub-module rlm_eap_peap peap { tls = "tls-common" default_eap_type = "mschapv2" copy_request_to_tunnel = no use_tunneled_reply = no proxy_tunneled_request_as_eap = yes virtual_server = "inner-tunnel" soh = no require_client_cert = no } tls: Using cached TLS configuration from previous invocation # Linked to sub-module rlm_eap_mschapv2 mschapv2 { with_ntdomain_hack = no send_error = no } # Instantiating module "mschap" from file /etc/freeradius/3.0/mods-enabled/mschap rlm_mschap (mschap): using internal authentication # Instantiating module "etc_passwd" from file /etc/freeradius/3.0/mods-enabled/passwd rlm_passwd: nfields: 3 keyfield 0(User-Name) listable: no } # modules radiusd: #### Loading Virtual Servers #### server { # from file /etc/freeradius/3.0/radiusd.conf } # server server inner-tunnel { # from file /etc/freeradius/3.0/sites-enabled/inner-tunnel # Loading authenticate {...} # Loading authorize {...} Ignoring "sql" (see raddb/mods-available/README.rst) # Loading session {...} # Loading post-proxy {...} # Loading post-auth {...} } # server inner-tunnel server default { # from file /etc/freeradius/3.0/sites-enabled/default # Loading authenticate {...} # Loading authorize {...} # Loading preacct {...} # Loading accounting {...} # Loading post-proxy {...} # Loading post-auth {...} } # server default radiusd: #### Opening IP addresses and Ports #### listen { type = "auth" ipaddr = 127.0.0.1 port = 18120 } listen { type = "auth" ipaddr = * port = 0 limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } listen { type = "acct" ipaddr = * port = 0 limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } listen { type = "auth" ipv6addr = :: port = 0 limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } listen { type = "acct" ipv6addr = :: port = 0 limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } Listening on auth address 127.0.0.1 port 18120 bound to server inner-tunnel Listening on auth address * port 1812 bound to server default Listening on acct address * port 1813 bound to server default Listening on auth address :: port 1812 bound to server default Listening on acct address :: port 1813 bound to server default Listening on proxy address * port 40729 Listening on proxy address :: port 42721 Ready to process requests (0) Received Access-Request Id 82 from 10.1.25.208:58067 to 10.251.16.50:1812 length 289 (0) Acct-Session-Id = "5CFEDE60-1B69AD04" (0) User-Name = "donkey" (0) NAS-IP-Address = 10.1.25.208 (0) NAS-Identifier = "18-7C-0B-59-10-6C" (0) NAS-Port = 1 (0) Called-Station-Id = "18-7C-0B-59-10-6C:STAFF1" (0) Calling-Station-Id = "28-F0-76-1A-05-C6" (0) Service-Type = Framed-User (0) Chargeable-User-Identity = 0x00 (0) NAS-Port-Type = Wireless-802.11 (0) Connect-Info = "CONNECT 802.11a/n/ac" (0) EAP-Message = 0x0200000f016367726f73736b6f7066 (0) Ruckus-SSID = "STAFF1" (0) Ruckus-BSSID = 0x187c0b59106c (0) Ruckus-Wlan-Id = 5 (0) Ruckus-VLAN-ID = 16 (0) Ruckus-SCG-CBlade-IP = 167844299 (0) Ruckus-Zone-Name = "MAIN" (0) Ruckus-Wlan-Name = "STAFF1" (0) Message-Authenticator = 0xabb37aec732768bf882d3b1baf6df572 (0) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (0) authorize { (0) policy filter_username { (0) if (&User-Name) { (0) if (&User-Name) -> TRUE (0) if (&User-Name) { (0) if (&User-Name =~ / /) { (0) if (&User-Name =~ / /) -> FALSE (0) if (&User-Name =~ /@[^@]*@/ ) { (0) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (0) if (&User-Name =~ /\.\./ ) { (0) if (&User-Name =~ /\.\./ ) -> FALSE (0) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (0) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (0) if (&User-Name =~ /\.$/) { (0) if (&User-Name =~ /\.$/) -> FALSE (0) if (&User-Name =~ /(a)\./) { (0) if (&User-Name =~ /(a)\./) -> FALSE (0) } # if (&User-Name) = notfound (0) } # policy filter_username = notfound (0) [preprocess] = ok (0) [chap] = noop (0) [mschap] = noop (0) [digest] = noop (0) suffix: Checking for suffix after "@" (0) suffix: No '@' in User-Name = "donkey", looking up realm NULL (0) suffix: No such realm "NULL" (0) [suffix] = noop (0) eap: Peer sent EAP Response (code 2) ID 0 length 15 (0) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize (0) [eap] = ok (0) } # authorize = ok (0) Found Auth-Type = eap (0) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (0) authenticate { (0) eap: Peer sent packet with method EAP Identity (1) (0) eap: Calling submodule eap_md5 to process data (0) eap_md5: Issuing MD5 Challenge (0) eap: Sending EAP Request (code 1) ID 1 length 22 (0) eap: EAP session adding &reply:State = 0xeb0f33f9eb0e3761 (0) [eap] = handled (0) } # authenticate = handled (0) Using Post-Auth-Type Challenge (0) Post-Auth-Type sub-section not found. Ignoring. (0) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (0) Sent Access-Challenge Id 82 from 10.251.16.50:1812 to 10.1.25.208:58067 length 0 (0) EAP-Message = 0x010100160410b8b468348e0a4daf0ecc04e6949ae826 (0) Message-Authenticator = 0x00000000000000000000000000000000 (0) State = 0xeb0f33f9eb0e3761ce83e6b60363ea34 (0) Finished request Waking up in 4.9 seconds. (1) Received Access-Request Id 83 from 10.1.25.208:58067 to 10.251.16.50:1812 length 300 (1) Acct-Session-Id = "5CFEDE60-1B69AD04" (1) User-Name = "donkey" (1) NAS-IP-Address = 10.1.25.208 (1) NAS-Identifier = "18-7C-0B-59-10-6C" (1) NAS-Port = 1 (1) Called-Station-Id = "18-7C-0B-59-10-6C:STAFF1" (1) Calling-Station-Id = "28-F0-76-1A-05-C6" (1) Service-Type = Framed-User (1) Chargeable-User-Identity = 0x00 (1) NAS-Port-Type = Wireless-802.11 (1) Connect-Info = "CONNECT 802.11a/n/ac" (1) EAP-Message = 0x020100080319152b (1) State = 0xeb0f33f9eb0e3761ce83e6b60363ea34 (1) Ruckus-SSID = "STAFF1" (1) Ruckus-BSSID = 0x187c0b59106c (1) Ruckus-Wlan-Id = 5 (1) Ruckus-VLAN-ID = 16 (1) Ruckus-SCG-CBlade-IP = 167844299 (1) Ruckus-Zone-Name = "MAIN" (1) Ruckus-Wlan-Name = "STAFF1" (1) Message-Authenticator = 0x0b8b5b7266ea8d8f483e6f71936f9d69 (1) session-state: No cached attributes (1) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (1) authorize { (1) policy filter_username { (1) if (&User-Name) { (1) if (&User-Name) -> TRUE (1) if (&User-Name) { (1) if (&User-Name =~ / /) { (1) if (&User-Name =~ / /) -> FALSE (1) if (&User-Name =~ /@[^@]*@/ ) { (1) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (1) if (&User-Name =~ /\.\./ ) { (1) if (&User-Name =~ /\.\./ ) -> FALSE (1) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (1) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (1) if (&User-Name =~ /\.$/) { (1) if (&User-Name =~ /\.$/) -> FALSE (1) if (&User-Name =~ /(a)\./) { (1) if (&User-Name =~ /(a)\./) -> FALSE (1) } # if (&User-Name) = notfound (1) } # policy filter_username = notfound (1) [preprocess] = ok (1) [chap] = noop (1) [mschap] = noop (1) [digest] = noop (1) suffix: Checking for suffix after "@" (1) suffix: No '@' in User-Name = "donkey", looking up realm NULL (1) suffix: No such realm "NULL" (1) [suffix] = noop (1) eap: Peer sent EAP Response (code 2) ID 1 length 8 (1) eap: No EAP Start, assuming it's an on-going EAP conversation (1) [eap] = updated (1) [files] = noop rlm_ldap (ldap): Reserved connection (0) (1) ldap: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (1) ldap: --> (uid=donkey) (1) ldap: Performing search in "dc=burro,dc=org" with filter "(uid=donkey)", scope "sub" (1) ldap: Waiting for search result... (1) ldap: User object found at DN "uid=donkey,ou=Animals,ou=Users,dc=burro,dc=org" (1) ldap: Processing user attributes (1) ldap: WARNING: No "known good" password added. Ensure the admin user has permission to read the password attribute (1) ldap: WARNING: PAP authentication will *NOT* work with Active Directory (if that is what you were trying to configure) rlm_ldap (ldap): Released connection (0) rlm_ldap (ldap): Need 5 more connections to reach 10 spares rlm_ldap (ldap): Opening additional connection (5), 1 of 27 pending slots used rlm_ldap (ldap): Connecting to ldaps://ldap.google.com:636 rlm_ldap (ldap): Waiting for bind result... rlm_ldap (ldap): Bind successful (1) [ldap] = ok (1) [expiration] = noop (1) [logintime] = noop (1) pap: WARNING: No "known good" password found for the user. Not setting Auth-Type (1) pap: WARNING: Authentication will fail unless a "known good" password is available (1) [pap] = noop (1) if (User-Password) { (1) if (User-Password) -> FALSE (1) } # authorize = updated (1) Found Auth-Type = eap (1) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (1) authenticate { (1) eap: Expiring EAP session with state 0xeb0f33f9eb0e3761 (1) eap: Finished EAP session with state 0xeb0f33f9eb0e3761 (1) eap: Previous EAP request found for state 0xeb0f33f9eb0e3761, released from the list (1) eap: Peer sent packet with method EAP NAK (3) (1) eap: Found mutually acceptable type PEAP (25) (1) eap: Calling submodule eap_peap to process data (1) eap_peap: Initiating new EAP-TLS session (1) eap_peap: [eaptls start] = request (1) eap: Sending EAP Request (code 1) ID 2 length 6 (1) eap: EAP session adding &reply:State = 0xeb0f33f9ea0d2a61 (1) [eap] = handled (1) } # authenticate = handled (1) Using Post-Auth-Type Challenge (1) Post-Auth-Type sub-section not found. Ignoring. (1) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (1) Sent Access-Challenge Id 83 from 10.251.16.50:1812 to 10.1.25.208:58067 length 0 (1) EAP-Message = 0x010200061920 (1) Message-Authenticator = 0x00000000000000000000000000000000 (1) State = 0xeb0f33f9ea0d2a61ce83e6b60363ea34 (1) Finished request Waking up in 4.1 seconds. (2) Received Access-Request Id 84 from 10.1.25.208:58067 to 10.251.16.50:1812 length 453 (2) Acct-Session-Id = "5CFEDE60-1B69AD04" (2) User-Name = "donkey" (2) NAS-IP-Address = 10.1.25.208 (2) NAS-Identifier = "18-7C-0B-59-10-6C" (2) NAS-Port = 1 (2) Called-Station-Id = "18-7C-0B-59-10-6C:STAFF1" (2) Calling-Station-Id = "28-F0-76-1A-05-C6" (2) Service-Type = Framed-User (2) Chargeable-User-Identity = 0x00 (2) NAS-Port-Type = Wireless-802.11 (2) Connect-Info = "CONNECT 802.11a/n/ac" (2) EAP-Message = 0x020200a119800000009716030100920100008e03035cfede6254095d49bd63bd295e703470aa11619b0acf539a1e28ac5cc475f25100002c00ffc02cc02bc024c023c00ac009c008c030c02fc028c027c014c013c012009d009c003d003c0035002f000a01000039000a000 (2) State = 0xeb0f33f9ea0d2a61ce83e6b60363ea34 (2) Ruckus-SSID = "STAFF1" (2) Ruckus-BSSID = 0x187c0b59106c (2) Ruckus-Wlan-Id = 5 (2) Ruckus-VLAN-ID = 16 (2) Ruckus-SCG-CBlade-IP = 167844299 (2) Ruckus-Zone-Name = "MAIN" (2) Ruckus-Wlan-Name = "STAFF1" (2) Message-Authenticator = 0xd60bcb324cd87ecd8dfec4a8e4a58544 (2) session-state: No cached attributes (2) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (2) authorize { (2) policy filter_username { (2) if (&User-Name) { (2) if (&User-Name) -> TRUE (2) if (&User-Name) { (2) if (&User-Name =~ / /) { (2) if (&User-Name =~ / /) -> FALSE (2) if (&User-Name =~ /@[^@]*@/ ) { (2) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (2) if (&User-Name =~ /\.\./ ) { (2) if (&User-Name =~ /\.\./ ) -> FALSE (2) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (2) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (2) if (&User-Name =~ /\.$/) { (2) if (&User-Name =~ /\.$/) -> FALSE (2) if (&User-Name =~ /(a)\./) { (2) if (&User-Name =~ /(a)\./) -> FALSE (2) } # if (&User-Name) = notfound (2) } # policy filter_username = notfound (2) [preprocess] = ok (2) [chap] = noop (2) [mschap] = noop (2) [digest] = noop (2) suffix: Checking for suffix after "@" (2) suffix: No '@' in User-Name = "donkey", looking up realm NULL (2) suffix: No such realm "NULL" (2) [suffix] = noop (2) eap: Peer sent EAP Response (code 2) ID 2 length 161 (2) eap: Continuing tunnel setup (2) [eap] = ok (2) } # authorize = ok (2) Found Auth-Type = eap (2) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (2) authenticate { (2) eap: Expiring EAP session with state 0xeb0f33f9ea0d2a61 (2) eap: Finished EAP session with state 0xeb0f33f9ea0d2a61 (2) eap: Previous EAP request found for state 0xeb0f33f9ea0d2a61, released from the list (2) eap: Peer sent packet with method EAP PEAP (25) (2) eap: Calling submodule eap_peap to process data (2) eap_peap: Continuing EAP-TLS (2) eap_peap: Peer indicated complete TLS record size will be 151 bytes (2) eap_peap: Got complete TLS record (151 bytes) (2) eap_peap: [eaptls verify] = length included (2) eap_peap: (other): before SSL initialization (2) eap_peap: TLS_accept: before SSL initialization (2) eap_peap: TLS_accept: before SSL initialization (2) eap_peap: <<< recv TLS 1.2 [length 0092] (2) eap_peap: TLS_accept: SSLv3/TLS read client hello (2) eap_peap: >>> send TLS 1.2 [length 003d] (2) eap_peap: TLS_accept: SSLv3/TLS write server hello (2) eap_peap: >>> send TLS 1.2 [length 02f1] (2) eap_peap: TLS_accept: SSLv3/TLS write certificate (2) eap_peap: >>> send TLS 1.2 [length 014d] (2) eap_peap: TLS_accept: SSLv3/TLS write key exchange (2) eap_peap: >>> send TLS 1.2 [length 0004] (2) eap_peap: TLS_accept: SSLv3/TLS write server done (2) eap_peap: TLS_accept: Need to read more data: SSLv3/TLS write server done (2) eap_peap: In SSL Handshake Phase (2) eap_peap: In SSL Accept mode (2) eap_peap: [eaptls process] = handled (2) eap: Sending EAP Request (code 1) ID 3 length 1004 (2) eap: EAP session adding &reply:State = 0xeb0f33f9e90c2a61 (2) [eap] = handled (2) } # authenticate = handled (2) Using Post-Auth-Type Challenge (2) Post-Auth-Type sub-section not found. Ignoring. (2) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (2) Sent Access-Challenge Id 84 from 10.251.16.50:1812 to 10.1.25.208:58067 length 0 (2) EAP-Message = 0x010303ec19c000000493160303003d020000390303ec4487452b5f1fb5ba794059ea0d6d5b877ae2e899921074222b5d1f847af2d600c030000011ff01000100000b0004030001020017000016030302f10b0002ed0002ea0002e7308202e3308201cba0030201020209009 (2) Message-Authenticator = 0x00000000000000000000000000000000 (2) State = 0xeb0f33f9e90c2a61ce83e6b60363ea34 (2) Finished request Waking up in 4.1 seconds. (3) Received Access-Request Id 85 from 10.1.25.208:58067 to 10.251.16.50:1812 length 298 (3) Acct-Session-Id = "5CFEDE60-1B69AD04" (3) User-Name = "donkey" (3) NAS-IP-Address = 10.1.25.208 (3) NAS-Identifier = "18-7C-0B-59-10-6C" (3) NAS-Port = 1 (3) Called-Station-Id = "18-7C-0B-59-10-6C:STAFF1" (3) Calling-Station-Id = "28-F0-76-1A-05-C6" (3) Service-Type = Framed-User (3) Chargeable-User-Identity = 0x00 (3) NAS-Port-Type = Wireless-802.11 (3) Connect-Info = "CONNECT 802.11a/n/ac" (3) EAP-Message = 0x020300061900 (3) State = 0xeb0f33f9e90c2a61ce83e6b60363ea34 (3) Ruckus-SSID = "STAFF1" (3) Ruckus-BSSID = 0x187c0b59106c (3) Ruckus-Wlan-Id = 5 (3) Ruckus-VLAN-ID = 16 (3) Ruckus-SCG-CBlade-IP = 167844299 (3) Ruckus-Zone-Name = "MAIN" (3) Ruckus-Wlan-Name = "STAFF1" (3) Message-Authenticator = 0x00bfef65f6da6de45b7e7c344ca914fd (3) session-state: No cached attributes (3) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (3) authorize { (3) policy filter_username { (3) if (&User-Name) { (3) if (&User-Name) -> TRUE (3) if (&User-Name) { (3) if (&User-Name =~ / /) { (3) if (&User-Name =~ / /) -> FALSE (3) if (&User-Name =~ /@[^@]*@/ ) { (3) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (3) if (&User-Name =~ /\.\./ ) { (3) if (&User-Name =~ /\.\./ ) -> FALSE (3) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (3) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (3) if (&User-Name =~ /\.$/) { (3) if (&User-Name =~ /\.$/) -> FALSE (3) if (&User-Name =~ /(a)\./) { (3) if (&User-Name =~ /(a)\./) -> FALSE (3) } # if (&User-Name) = notfound (3) } # policy filter_username = notfound (3) [preprocess] = ok (3) [chap] = noop (3) [mschap] = noop (3) [digest] = noop (3) suffix: Checking for suffix after "@" (3) suffix: No '@' in User-Name = "donkey", looking up realm NULL (3) suffix: No such realm "NULL" (3) [suffix] = noop (3) eap: Peer sent EAP Response (code 2) ID 3 length 6 (3) eap: Continuing tunnel setup (3) [eap] = ok (3) } # authorize = ok (3) Found Auth-Type = eap (3) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (3) authenticate { (3) eap: Expiring EAP session with state 0xeb0f33f9e90c2a61 (3) eap: Finished EAP session with state 0xeb0f33f9e90c2a61 (3) eap: Previous EAP request found for state 0xeb0f33f9e90c2a61, released from the list (3) eap: Peer sent packet with method EAP PEAP (25) (3) eap: Calling submodule eap_peap to process data (3) eap_peap: Continuing EAP-TLS (3) eap_peap: Peer ACKed our handshake fragment (3) eap_peap: [eaptls verify] = request (3) eap_peap: [eaptls process] = handled (3) eap: Sending EAP Request (code 1) ID 4 length 183 (3) eap: EAP session adding &reply:State = 0xeb0f33f9e80b2a61 (3) [eap] = handled (3) } # authenticate = handled (3) Using Post-Auth-Type Challenge (3) Post-Auth-Type sub-section not found. Ignoring. (3) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (3) Sent Access-Challenge Id 85 from 10.251.16.50:1812 to 10.1.25.208:58067 length 0 (3) EAP-Message = 0x010400b71900a1a29b66f95de8004c8245181cbf9f23b4a7d479292bfa74962a915dd8774a2523676d92f7dfa80932789370c76b891e274a0344206e5d5072ada0c21a8921e6b74fcf47341dc2c57863a6c600eba45681356a575c5953296da0275684325a4ac411b224b64 (3) Message-Authenticator = 0x00000000000000000000000000000000 (3) State = 0xeb0f33f9e80b2a61ce83e6b60363ea34 (3) Finished request Waking up in 4.1 seconds. (4) Received Access-Request Id 86 from 10.1.25.208:58067 to 10.251.16.50:1812 length 428 (4) Acct-Session-Id = "5CFEDE60-1B69AD04" (4) User-Name = "donkey" (4) NAS-IP-Address = 10.1.25.208 (4) NAS-Identifier = "18-7C-0B-59-10-6C" (4) NAS-Port = 1 (4) Called-Station-Id = "18-7C-0B-59-10-6C:STAFF1" (4) Calling-Station-Id = "28-F0-76-1A-05-C6" (4) Service-Type = Framed-User (4) Chargeable-User-Identity = 0x00 (4) NAS-Port-Type = Wireless-802.11 (4) Connect-Info = "CONNECT 802.11a/n/ac" (4) EAP-Message = 0x0204008819800000007e16030300461000004241046a8ce96dd2e79dcf4274695af82e3429db8cf218baea8842e877d8e53d5af5ad90d0ca34a7bedd750d51282438e22b40376bb2c7658ea62e5e44a9a0b364d1611403030001011603030028ac32e57bfad56383076dd17 (4) State = 0xeb0f33f9e80b2a61ce83e6b60363ea34 (4) Ruckus-SSID = "STAFF1" (4) Ruckus-BSSID = 0x187c0b59106c (4) Ruckus-Wlan-Id = 5 (4) Ruckus-VLAN-ID = 16 (4) Ruckus-SCG-CBlade-IP = 167844299 (4) Ruckus-Zone-Name = "MAIN" (4) Ruckus-Wlan-Name = "STAFF1" (4) Message-Authenticator = 0x91fe336e00013ce58b87218e146eb362 (4) session-state: No cached attributes (4) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (4) authorize { (4) policy filter_username { (4) if (&User-Name) { (4) if (&User-Name) -> TRUE (4) if (&User-Name) { (4) if (&User-Name =~ / /) { (4) if (&User-Name =~ / /) -> FALSE (4) if (&User-Name =~ /@[^@]*@/ ) { (4) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (4) if (&User-Name =~ /\.\./ ) { (4) if (&User-Name =~ /\.\./ ) -> FALSE (4) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (4) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (4) if (&User-Name =~ /\.$/) { (4) if (&User-Name =~ /\.$/) -> FALSE (4) if (&User-Name =~ /(a)\./) { (4) if (&User-Name =~ /(a)\./) -> FALSE (4) } # if (&User-Name) = notfound (4) } # policy filter_username = notfound (4) [preprocess] = ok (4) [chap] = noop (4) [mschap] = noop (4) [digest] = noop (4) suffix: Checking for suffix after "@" (4) suffix: No '@' in User-Name = "donkey", looking up realm NULL (4) suffix: No such realm "NULL" (4) [suffix] = noop (4) eap: Peer sent EAP Response (code 2) ID 4 length 136 (4) eap: Continuing tunnel setup (4) [eap] = ok (4) } # authorize = ok (4) Found Auth-Type = eap (4) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (4) authenticate { (4) eap: Expiring EAP session with state 0xeb0f33f9e80b2a61 (4) eap: Finished EAP session with state 0xeb0f33f9e80b2a61 (4) eap: Previous EAP request found for state 0xeb0f33f9e80b2a61, released from the list (4) eap: Peer sent packet with method EAP PEAP (25) (4) eap: Calling submodule eap_peap to process data (4) eap_peap: Continuing EAP-TLS (4) eap_peap: Peer indicated complete TLS record size will be 126 bytes (4) eap_peap: Got complete TLS record (126 bytes) (4) eap_peap: [eaptls verify] = length included (4) eap_peap: TLS_accept: SSLv3/TLS write server done (4) eap_peap: <<< recv TLS 1.2 [length 0046] (4) eap_peap: TLS_accept: SSLv3/TLS read client key exchange (4) eap_peap: TLS_accept: SSLv3/TLS read change cipher spec (4) eap_peap: <<< recv TLS 1.2 [length 0010] (4) eap_peap: TLS_accept: SSLv3/TLS read finished (4) eap_peap: >>> send TLS 1.2 [length 0001] (4) eap_peap: TLS_accept: SSLv3/TLS write change cipher spec (4) eap_peap: >>> send TLS 1.2 [length 0010] (4) eap_peap: TLS_accept: SSLv3/TLS write finished (4) eap_peap: (other): SSL negotiation finished successfully (4) eap_peap: SSL Connection Established (4) eap_peap: [eaptls process] = handled (4) eap: Sending EAP Request (code 1) ID 5 length 57 (4) eap: EAP session adding &reply:State = 0xeb0f33f9ef0a2a61 (4) [eap] = handled (4) } # authenticate = handled (4) Using Post-Auth-Type Challenge (4) Post-Auth-Type sub-section not found. Ignoring. (4) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (4) Sent Access-Challenge Id 86 from 10.251.16.50:1812 to 10.1.25.208:58067 length 0 (4) EAP-Message = 0x01050039190014030300010116030300280b2330975c35e8e635f254e800229cae0fe90eb8b7fe5ddccc04fa2a79902a3a72ee710e8af88deb (4) Message-Authenticator = 0x00000000000000000000000000000000 (4) State = 0xeb0f33f9ef0a2a61ce83e6b60363ea34 (4) Finished request Waking up in 4.1 seconds. (5) Received Access-Request Id 87 from 10.1.25.208:58067 to 10.251.16.50:1812 length 298 (5) Acct-Session-Id = "5CFEDE60-1B69AD04" (5) User-Name = "donkey" (5) NAS-IP-Address = 10.1.25.208 (5) NAS-Identifier = "18-7C-0B-59-10-6C" (5) NAS-Port = 1 (5) Called-Station-Id = "18-7C-0B-59-10-6C:STAFF1" (5) Calling-Station-Id = "28-F0-76-1A-05-C6" (5) Service-Type = Framed-User (5) Chargeable-User-Identity = 0x00 (5) NAS-Port-Type = Wireless-802.11 (5) Connect-Info = "CONNECT 802.11a/n/ac" (5) EAP-Message = 0x020500061900 (5) State = 0xeb0f33f9ef0a2a61ce83e6b60363ea34 (5) Ruckus-SSID = "STAFF1" (5) Ruckus-BSSID = 0x187c0b59106c (5) Ruckus-Wlan-Id = 5 (5) Ruckus-VLAN-ID = 16 (5) Ruckus-SCG-CBlade-IP = 167844299 (5) Ruckus-Zone-Name = "MAIN" (5) Ruckus-Wlan-Name = "STAFF1" (5) Message-Authenticator = 0x482575750aa8d6d755fec98b2f0e9b5c (5) session-state: No cached attributes (5) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (5) authorize { (5) policy filter_username { (5) if (&User-Name) { (5) if (&User-Name) -> TRUE (5) if (&User-Name) { (5) if (&User-Name =~ / /) { (5) if (&User-Name =~ / /) -> FALSE (5) if (&User-Name =~ /@[^@]*@/ ) { (5) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (5) if (&User-Name =~ /\.\./ ) { (5) if (&User-Name =~ /\.\./ ) -> FALSE (5) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (5) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (5) if (&User-Name =~ /\.$/) { (5) if (&User-Name =~ /\.$/) -> FALSE (5) if (&User-Name =~ /(a)\./) { (5) if (&User-Name =~ /(a)\./) -> FALSE (5) } # if (&User-Name) = notfound (5) } # policy filter_username = notfound (5) [preprocess] = ok (5) [chap] = noop (5) [mschap] = noop (5) [digest] = noop (5) suffix: Checking for suffix after "@" (5) suffix: No '@' in User-Name = "donkey", looking up realm NULL (5) suffix: No such realm "NULL" (5) [suffix] = noop (5) eap: Peer sent EAP Response (code 2) ID 5 length 6 (5) eap: Continuing tunnel setup (5) [eap] = ok (5) } # authorize = ok (5) Found Auth-Type = eap (5) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (5) authenticate { (5) eap: Expiring EAP session with state 0xeb0f33f9ef0a2a61 (5) eap: Finished EAP session with state 0xeb0f33f9ef0a2a61 (5) eap: Previous EAP request found for state 0xeb0f33f9ef0a2a61, released from the list (5) eap: Peer sent packet with method EAP PEAP (25) (5) eap: Calling submodule eap_peap to process data (5) eap_peap: Continuing EAP-TLS (5) eap_peap: Peer ACKed our handshake fragment. handshake is finished (5) eap_peap: [eaptls verify] = success (5) eap_peap: [eaptls process] = success (5) eap_peap: Session established. Decoding tunneled attributes (5) eap_peap: PEAP state TUNNEL ESTABLISHED (5) eap: Sending EAP Request (code 1) ID 6 length 40 (5) eap: EAP session adding &reply:State = 0xeb0f33f9ee092a61 (5) [eap] = handled (5) } # authenticate = handled (5) Using Post-Auth-Type Challenge (5) Post-Auth-Type sub-section not found. Ignoring. (5) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (5) Sent Access-Challenge Id 87 from 10.251.16.50:1812 to 10.1.25.208:58067 length 0 (5) EAP-Message = 0x010600281900170303001d0b2330975c35e8e771c29d08efbd904f285fc7913a39771a0666079800 (5) Message-Authenticator = 0x00000000000000000000000000000000 (5) State = 0xeb0f33f9ee092a61ce83e6b60363ea34 (5) Finished request Waking up in 4.1 seconds. (6) Received Access-Request Id 88 from 10.1.25.208:58067 to 10.251.16.50:1812 length 338 (6) Acct-Session-Id = "5CFEDE60-1B69AD04" (6) User-Name = "donkey" (6) NAS-IP-Address = 10.1.25.208 (6) NAS-Identifier = "18-7C-0B-59-10-6C" (6) NAS-Port = 1 (6) Called-Station-Id = "18-7C-0B-59-10-6C:STAFF1" (6) Calling-Station-Id = "28-F0-76-1A-05-C6" (6) Service-Type = Framed-User (6) Chargeable-User-Identity = 0x00 (6) NAS-Port-Type = Wireless-802.11 (6) Connect-Info = "CONNECT 802.11a/n/ac" (6) EAP-Message = 0x0206002e19001703030023ac32e57bfad5638438fe9d07fadaa4d125b8ba070d562d74853d930c154f60657b8f76 (6) State = 0xeb0f33f9ee092a61ce83e6b60363ea34 (6) Ruckus-SSID = "STAFF1" (6) Ruckus-BSSID = 0x187c0b59106c (6) Ruckus-Wlan-Id = 5 (6) Ruckus-VLAN-ID = 16 (6) Ruckus-SCG-CBlade-IP = 167844299 (6) Ruckus-Zone-Name = "MAIN" (6) Ruckus-Wlan-Name = "STAFF1" (6) Message-Authenticator = 0x6f6fa288d194d0df748524c52c8d175a (6) session-state: No cached attributes (6) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (6) authorize { (6) policy filter_username { (6) if (&User-Name) { (6) if (&User-Name) -> TRUE (6) if (&User-Name) { (6) if (&User-Name =~ / /) { (6) if (&User-Name =~ / /) -> FALSE (6) if (&User-Name =~ /@[^@]*@/ ) { (6) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (6) if (&User-Name =~ /\.\./ ) { (6) if (&User-Name =~ /\.\./ ) -> FALSE (6) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (6) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (6) if (&User-Name =~ /\.$/) { (6) if (&User-Name =~ /\.$/) -> FALSE (6) if (&User-Name =~ /(a)\./) { (6) if (&User-Name =~ /(a)\./) -> FALSE (6) } # if (&User-Name) = notfound (6) } # policy filter_username = notfound (6) [preprocess] = ok (6) [chap] = noop (6) [mschap] = noop (6) [digest] = noop (6) suffix: Checking for suffix after "@" (6) suffix: No '@' in User-Name = "donkey", looking up realm NULL (6) suffix: No such realm "NULL" (6) [suffix] = noop (6) eap: Peer sent EAP Response (code 2) ID 6 length 46 (6) eap: Continuing tunnel setup (6) [eap] = ok (6) } # authorize = ok (6) Found Auth-Type = eap (6) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (6) authenticate { (6) eap: Expiring EAP session with state 0xeb0f33f9ee092a61 (6) eap: Finished EAP session with state 0xeb0f33f9ee092a61 (6) eap: Previous EAP request found for state 0xeb0f33f9ee092a61, released from the list (6) eap: Peer sent packet with method EAP PEAP (25) (6) eap: Calling submodule eap_peap to process data (6) eap_peap: Continuing EAP-TLS (6) eap_peap: [eaptls verify] = ok (6) eap_peap: Done initial handshake (6) eap_peap: [eaptls process] = ok (6) eap_peap: Session established. Decoding tunneled attributes (6) eap_peap: PEAP state WAITING FOR INNER IDENTITY (6) eap_peap: Identity - donkey (6) eap_peap: Got inner identity 'donkey' (6) eap_peap: Setting default EAP type for tunneled EAP session (6) eap_peap: Got tunneled request (6) eap_peap: EAP-Message = 0x0206000f016367726f73736b6f7066 (6) eap_peap: Setting User-Name to donkey (6) eap_peap: Sending tunneled request to inner-tunnel (6) eap_peap: EAP-Message = 0x0206000f016367726f73736b6f7066 (6) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1 (6) eap_peap: User-Name = "donkey" (6) Virtual server inner-tunnel received request (6) EAP-Message = 0x0206000f016367726f73736b6f7066 (6) FreeRADIUS-Proxied-To = 127.0.0.1 (6) User-Name = "donkey" (6) WARNING: Outer and inner identities are the same. User privacy is compromised. (6) server inner-tunnel { (6) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/inner-tunnel (6) authorize { (6) policy filter_username { (6) if (&User-Name) { (6) if (&User-Name) -> TRUE (6) if (&User-Name) { (6) if (&User-Name =~ / /) { (6) if (&User-Name =~ / /) -> FALSE (6) if (&User-Name =~ /@[^@]*@/ ) { (6) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (6) if (&User-Name =~ /\.\./ ) { (6) if (&User-Name =~ /\.\./ ) -> FALSE (6) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (6) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (6) if (&User-Name =~ /\.$/) { (6) if (&User-Name =~ /\.$/) -> FALSE (6) if (&User-Name =~ /(a)\./) { (6) if (&User-Name =~ /(a)\./) -> FALSE (6) } # if (&User-Name) = notfound (6) } # policy filter_username = notfound (6) suffix: Checking for suffix after "@" (6) suffix: No '@' in User-Name = "donkey", looking up realm NULL (6) suffix: No such realm "NULL" (6) [suffix] = noop (6) update control { (6) &Proxy-To-Realm := LOCAL (6) } # update control = noop (6) eap: Peer sent EAP Response (code 2) ID 6 length 15 (6) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize (6) [eap] = ok (6) } # authorize = ok (6) Found Auth-Type = eap (6) # Executing group from file /etc/freeradius/3.0/sites-enabled/inner-tunnel (6) authenticate { (6) eap: Peer sent packet with method EAP Identity (1) (6) eap: Calling submodule eap_mschapv2 to process data (6) eap_mschapv2: Issuing Challenge (6) eap: Sending EAP Request (code 1) ID 7 length 43 (6) eap: EAP session adding &reply:State = 0x51e14a5951e65099 (6) [eap] = handled (6) } # authenticate = handled (6) } # server inner-tunnel (6) Virtual server sending reply (6) EAP-Message = 0x0107002b1a0107002610f20e6c7657e18ddf266e1644efa62536667265657261646975732d332e302e3132 (6) Message-Authenticator = 0x00000000000000000000000000000000 (6) State = 0x51e14a5951e650990b18921f653a810f (6) eap_peap: Got tunneled reply code 11 (6) eap_peap: EAP-Message = 0x0107002b1a0107002610f20e6c7657e18ddf266e1644efa62536667265657261646975732d332e302e3132 (6) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (6) eap_peap: State = 0x51e14a5951e650990b18921f653a810f (6) eap_peap: Got tunneled reply RADIUS code 11 (6) eap_peap: EAP-Message = 0x0107002b1a0107002610f20e6c7657e18ddf266e1644efa62536667265657261646975732d332e302e3132 (6) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (6) eap_peap: State = 0x51e14a5951e650990b18921f653a810f (6) eap_peap: Got tunneled Access-Challenge (6) eap: Sending EAP Request (code 1) ID 7 length 74 (6) eap: EAP session adding &reply:State = 0xeb0f33f9ed082a61 (6) [eap] = handled (6) } # authenticate = handled (6) Using Post-Auth-Type Challenge (6) Post-Auth-Type sub-section not found. Ignoring. (6) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (6) Sent Access-Challenge Id 88 from 10.251.16.50:1812 to 10.1.25.208:58067 length 0 (6) EAP-Message = 0x0107004a1900170303003f0b2330975c35e8e8b2276f20245b6124662b9bd8da19f4c47411a4d7d0d6e10d45ba35319ae5c54e0246619deb19b66b16242f32cd16f225578e40dc8a3e98 (6) Message-Authenticator = 0x00000000000000000000000000000000 (6) State = 0xeb0f33f9ed082a61ce83e6b60363ea34 (6) Finished request Waking up in 4.1 seconds. (7) Received Access-Request Id 89 from 10.1.25.208:58067 to 10.251.16.50:1812 length 392 (7) Acct-Session-Id = "5CFEDE60-1B69AD04" (7) User-Name = "donkey" (7) NAS-IP-Address = 10.1.25.208 (7) NAS-Identifier = "18-7C-0B-59-10-6C" (7) NAS-Port = 1 (7) Called-Station-Id = "18-7C-0B-59-10-6C:STAFF1" (7) Calling-Station-Id = "28-F0-76-1A-05-C6" (7) Service-Type = Framed-User (7) Chargeable-User-Identity = 0x00 (7) NAS-Port-Type = Wireless-802.11 (7) Connect-Info = "CONNECT 802.11a/n/ac" (7) EAP-Message = 0x0207006419001703030059ac32e57bfad563851bc9fd7df25ee6a60f93167a11020bd796065bbd01c5b3b3ee291d68be4e15fc291bb850fd90b90f39b0f7b13da7ea3ab0474b00e2d57f275110390d0cc8e1f1ee29a05a06fa88a88c8a785e6bb8d34bad (7) State = 0xeb0f33f9ed082a61ce83e6b60363ea34 (7) Ruckus-SSID = "STAFF1" (7) Ruckus-BSSID = 0x187c0b59106c (7) Ruckus-Wlan-Id = 5 (7) Ruckus-VLAN-ID = 16 (7) Ruckus-SCG-CBlade-IP = 167844299 (7) Ruckus-Zone-Name = "MAIN" (7) Ruckus-Wlan-Name = "STAFF1" (7) Message-Authenticator = 0xdf8fc6ae10cd2b42cd387a757861c295 (7) session-state: No cached attributes (7) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (7) authorize { (7) policy filter_username { (7) if (&User-Name) { (7) if (&User-Name) -> TRUE (7) if (&User-Name) { (7) if (&User-Name =~ / /) { (7) if (&User-Name =~ / /) -> FALSE (7) if (&User-Name =~ /@[^@]*@/ ) { (7) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (7) if (&User-Name =~ /\.\./ ) { (7) if (&User-Name =~ /\.\./ ) -> FALSE (7) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (7) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (7) if (&User-Name =~ /\.$/) { (7) if (&User-Name =~ /\.$/) -> FALSE (7) if (&User-Name =~ /(a)\./) { (7) if (&User-Name =~ /(a)\./) -> FALSE (7) } # if (&User-Name) = notfound (7) } # policy filter_username = notfound (7) [preprocess] = ok (7) [chap] = noop (7) [mschap] = noop (7) [digest] = noop (7) suffix: Checking for suffix after "@" (7) suffix: No '@' in User-Name = "donkey", looking up realm NULL (7) suffix: No such realm "NULL" (7) [suffix] = noop (7) eap: Peer sent EAP Response (code 2) ID 7 length 100 (7) eap: Continuing tunnel setup (7) [eap] = ok (7) } # authorize = ok (7) Found Auth-Type = eap (7) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (7) authenticate { (7) eap: Expiring EAP session with state 0x51e14a5951e65099 (7) eap: Finished EAP session with state 0xeb0f33f9ed082a61 (7) eap: Previous EAP request found for state 0xeb0f33f9ed082a61, released from the list (7) eap: Peer sent packet with method EAP PEAP (25) (7) eap: Calling submodule eap_peap to process data (7) eap_peap: Continuing EAP-TLS (7) eap_peap: [eaptls verify] = ok (7) eap_peap: Done initial handshake (7) eap_peap: [eaptls process] = ok (7) eap_peap: Session established. Decoding tunneled attributes (7) eap_peap: PEAP state phase2 (7) eap_peap: EAP method MSCHAPv2 (26) (7) eap_peap: Got tunneled request (7) eap_peap: EAP-Message = 0x020700451a02070040317e26162a2707abeccaa28862ac0e39fa0000000000000000012a7f3c674b2789fe5f5cbc6218f4bb866415ba3d123f94006367726f73736b6f7066 (7) eap_peap: Setting User-Name to donkey (7) eap_peap: Sending tunneled request to inner-tunnel (7) eap_peap: EAP-Message = 0x020700451a02070040317e26162a2707abeccaa28862ac0e39fa0000000000000000012a7f3c674b2789fe5f5cbc6218f4bb866415ba3d123f94006367726f73736b6f7066 (7) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1 (7) eap_peap: User-Name = "donkey" (7) eap_peap: State = 0x51e14a5951e650990b18921f653a810f (7) Virtual server inner-tunnel received request (7) EAP-Message = 0x020700451a02070040317e26162a2707abeccaa28862ac0e39fa0000000000000000012a7f3c674b2789fe5f5cbc6218f4bb866415ba3d123f94006367726f73736b6f7066 (7) FreeRADIUS-Proxied-To = 127.0.0.1 (7) User-Name = "donkey" (7) State = 0x51e14a5951e650990b18921f653a810f (7) WARNING: Outer and inner identities are the same. User privacy is compromised. (7) server inner-tunnel { (7) session-state: No cached attributes (7) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/inner-tunnel (7) authorize { (7) policy filter_username { (7) if (&User-Name) { (7) if (&User-Name) -> TRUE (7) if (&User-Name) { (7) if (&User-Name =~ / /) { (7) if (&User-Name =~ / /) -> FALSE (7) if (&User-Name =~ /@[^@]*@/ ) { (7) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (7) if (&User-Name =~ /\.\./ ) { (7) if (&User-Name =~ /\.\./ ) -> FALSE (7) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (7) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (7) if (&User-Name =~ /\.$/) { (7) if (&User-Name =~ /\.$/) -> FALSE (7) if (&User-Name =~ /(a)\./) { (7) if (&User-Name =~ /(a)\./) -> FALSE (7) } # if (&User-Name) = notfound (7) } # policy filter_username = notfound (7) suffix: Checking for suffix after "@" (7) suffix: No '@' in User-Name = "donkey", looking up realm NULL (7) suffix: No such realm "NULL" (7) [suffix] = noop (7) update control { (7) &Proxy-To-Realm := LOCAL (7) } # update control = noop (7) eap: Peer sent EAP Response (code 2) ID 7 length 69 (7) eap: No EAP Start, assuming it's an on-going EAP conversation (7) [eap] = updated (7) [files] = noop rlm_ldap (ldap): Reserved connection (1) (7) ldap: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (7) ldap: --> (uid=donkey) (7) ldap: Performing search in "dc=burro,dc=org" with filter "(uid=donkey)", scope "sub" (7) ldap: Waiting for search result... (7) ldap: User object found at DN "uid=donkey,ou=Animals,ou=Users,dc=burro,dc=org" (7) ldap: Processing user attributes (7) ldap: WARNING: No "known good" password added. Ensure the admin user has permission to read the password attribute (7) ldap: WARNING: PAP authentication will *NOT* work with Active Directory (if that is what you were trying to configure) rlm_ldap (ldap): Released connection (1) (7) [ldap] = ok (7) [expiration] = noop (7) [logintime] = noop (7) [pap] = noop (7) if (User-Password) { (7) if (User-Password) -> FALSE (7) [mschap] = noop (7) } # authorize = updated (7) Found Auth-Type = eap (7) # Executing group from file /etc/freeradius/3.0/sites-enabled/inner-tunnel (7) authenticate { (7) eap: Expiring EAP session with state 0x51e14a5951e65099 (7) eap: Finished EAP session with state 0x51e14a5951e65099 (7) eap: Previous EAP request found for state 0x51e14a5951e65099, released from the list (7) eap: Peer sent packet with method EAP MSCHAPv2 (26) (7) eap: Calling submodule eap_mschapv2 to process data (7) eap_mschapv2: # Executing group from file /etc/freeradius/3.0/sites-enabled/inner-tunnel (7) eap_mschapv2: authenticate { (7) mschap: WARNING: No Cleartext-Password configured. Cannot create NT-Password (7) mschap: WARNING: No Cleartext-Password configured. Cannot create LM-Password (7) mschap: Creating challenge hash with username: donkey (7) mschap: Client is using MS-CHAPv2 (7) mschap: ERROR: FAILED: No NT/LM-Password. Cannot perform authentication (7) mschap: ERROR: MS-CHAP2-Response is incorrect (7) [mschap] = reject (7) } # authenticate = reject (7) eap: Sending EAP Failure (code 4) ID 7 length 4 (7) eap: Freeing handler (7) [eap] = reject (7) } # authenticate = reject (7) Failed to authenticate the user (7) Using Post-Auth-Type Reject (7) # Executing group from file /etc/freeradius/3.0/sites-enabled/inner-tunnel (7) Post-Auth-Type REJECT { (7) attr_filter.access_reject: EXPAND %{User-Name} (7) attr_filter.access_reject: --> donkey (7) attr_filter.access_reject: Matched entry DEFAULT at line 11 (7) [attr_filter.access_reject] = updated (7) update outer.session-state { (7) &Module-Failure-Message := &request:Module-Failure-Message -> 'mschap: FAILED: No NT/LM-Password. Cannot perform authentication' (7) } # update outer.session-state = noop (7) } # Post-Auth-Type REJECT = updated (7) } # server inner-tunnel (7) Virtual server sending reply (7) MS-CHAP-Error = "\007E=691 R=1 C=5655d99e064e2256aa10e59df3860df7 V=3 M=Authentication failed" (7) EAP-Message = 0x04070004 (7) Message-Authenticator = 0x00000000000000000000000000000000 (7) eap_peap: Got tunneled reply code 3 (7) eap_peap: MS-CHAP-Error = "\007E=691 R=1 C=5655d99e064e2256aa10e59df3860df7 V=3 M=Authentication failed" (7) eap_peap: EAP-Message = 0x04070004 (7) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (7) eap_peap: Got tunneled reply RADIUS code 3 (7) eap_peap: MS-CHAP-Error = "\007E=691 R=1 C=5655d99e064e2256aa10e59df3860df7 V=3 M=Authentication failed" (7) eap_peap: EAP-Message = 0x04070004 (7) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (7) eap_peap: Tunneled authentication was rejected (7) eap_peap: FAILURE (7) eap: Sending EAP Request (code 1) ID 8 length 46 (7) eap: EAP session adding &reply:State = 0xeb0f33f9ec072a61 (7) [eap] = handled (7) } # authenticate = handled (7) Using Post-Auth-Type Challenge (7) Post-Auth-Type sub-section not found. Ignoring. (7) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (7) session-state: Saving cached attributes (7) Module-Failure-Message := "mschap: FAILED: No NT/LM-Password. Cannot perform authentication" (7) Sent Access-Challenge Id 89 from 10.251.16.50:1812 to 10.1.25.208:58067 length 0 (7) EAP-Message = 0x0108002e190017030300230b2330975c35e8e9ddf79f42ef6e7756557b1d7292d8d6a7939dba671186bc3157b4e5 (7) Message-Authenticator = 0x00000000000000000000000000000000 (7) State = 0xeb0f33f9ec072a61ce83e6b60363ea34 (7) Finished request Waking up in 3.8 seconds. (8) Received Access-Request Id 90 from 10.1.25.208:58067 to 10.251.16.50:1812 length 338 (8) Acct-Session-Id = "5CFEDE60-1B69AD04" (8) User-Name = "donkey" (8) NAS-IP-Address = 10.1.25.208 (8) NAS-Identifier = "18-7C-0B-59-10-6C" (8) NAS-Port = 1 (8) Called-Station-Id = "18-7C-0B-59-10-6C:STAFF1" (8) Calling-Station-Id = "28-F0-76-1A-05-C6" (8) Service-Type = Framed-User (8) Chargeable-User-Identity = 0x00 (8) NAS-Port-Type = Wireless-802.11 (8) Connect-Info = "CONNECT 802.11a/n/ac" (8) EAP-Message = 0x0208002e19001703030023ac32e57bfad5638652a9471fbb614c7521ccdcdcf2cb7b6bb38d0350bcc3f6c0bc0c64 (8) State = 0xeb0f33f9ec072a61ce83e6b60363ea34 (8) Ruckus-SSID = "STAFF1" (8) Ruckus-BSSID = 0x187c0b59106c (8) Ruckus-Wlan-Id = 5 (8) Ruckus-VLAN-ID = 16 (8) Ruckus-SCG-CBlade-IP = 167844299 (8) Ruckus-Zone-Name = "MAIN" (8) Ruckus-Wlan-Name = "STAFF1" (8) Message-Authenticator = 0x3103c46759b6d6f8e2b7b6241363c9cc (8) Restoring &session-state (8) &session-state:Module-Failure-Message := "mschap: FAILED: No NT/LM-Password. Cannot perform authentication" (8) # Executing section authorize from file /etc/freeradius/3.0/sites-enabled/default (8) authorize { (8) policy filter_username { (8) if (&User-Name) { (8) if (&User-Name) -> TRUE (8) if (&User-Name) { (8) if (&User-Name =~ / /) { (8) if (&User-Name =~ / /) -> FALSE (8) if (&User-Name =~ /@[^@]*@/ ) { (8) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (8) if (&User-Name =~ /\.\./ ) { (8) if (&User-Name =~ /\.\./ ) -> FALSE (8) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (8) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (8) if (&User-Name =~ /\.$/) { (8) if (&User-Name =~ /\.$/) -> FALSE (8) if (&User-Name =~ /(a)\./) { (8) if (&User-Name =~ /(a)\./) -> FALSE (8) } # if (&User-Name) = notfound (8) } # policy filter_username = notfound (8) [preprocess] = ok (8) [chap] = noop (8) [mschap] = noop (8) [digest] = noop (8) suffix: Checking for suffix after "@" (8) suffix: No '@' in User-Name = "donkey", looking up realm NULL (8) suffix: No such realm "NULL" (8) [suffix] = noop (8) eap: Peer sent EAP Response (code 2) ID 8 length 46 (8) eap: Continuing tunnel setup (8) [eap] = ok (8) } # authorize = ok (8) Found Auth-Type = eap (8) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (8) authenticate { (8) eap: Expiring EAP session with state 0xeb0f33f9ec072a61 (8) eap: Finished EAP session with state 0xeb0f33f9ec072a61 (8) eap: Previous EAP request found for state 0xeb0f33f9ec072a61, released from the list (8) eap: Peer sent packet with method EAP PEAP (25) (8) eap: Calling submodule eap_peap to process data (8) eap_peap: Continuing EAP-TLS (8) eap_peap: [eaptls verify] = ok (8) eap_peap: Done initial handshake (8) eap_peap: [eaptls process] = ok (8) eap_peap: Session established. Decoding tunneled attributes (8) eap_peap: PEAP state send tlv failure (8) eap_peap: Received EAP-TLV response (8) eap_peap: The users session was previously rejected: returning reject (again.) (8) eap_peap: This means you need to read the PREVIOUS messages in the debug output (8) eap_peap: to find out the reason why the user was rejected (8) eap_peap: Look for "reject" or "fail". Those earlier messages will tell you (8) eap_peap: what went wrong, and how to fix the problem (8) eap: ERROR: Failed continuing EAP PEAP (25) session. EAP sub-module failed (8) eap: Sending EAP Failure (code 4) ID 8 length 4 (8) eap: Failed in EAP select (8) [eap] = invalid (8) } # authenticate = invalid (8) Failed to authenticate the user (8) Using Post-Auth-Type Reject (8) # Executing group from file /etc/freeradius/3.0/sites-enabled/default (8) Post-Auth-Type REJECT { (8) attr_filter.access_reject: EXPAND %{User-Name} (8) attr_filter.access_reject: --> donkey (8) attr_filter.access_reject: Matched entry DEFAULT at line 11 (8) [attr_filter.access_reject] = updated (8) [eap] = noop (8) policy remove_reply_message_if_eap { (8) if (&reply:EAP-Message && &reply:Reply-Message) { (8) if (&reply:EAP-Message && &reply:Reply-Message) -> FALSE (8) else { (8) [noop] = noop (8) } # else = noop (8) } # policy remove_reply_message_if_eap = noop (8) } # Post-Auth-Type REJECT = updated (8) Delaying response for 1.000000 seconds Waking up in 0.3 seconds. Waking up in 0.6 seconds. (8) Sending delayed response (8) Sent Access-Reject Id 90 from 10.251.16.50:1812 to 10.1.25.208:58067 length 44 (8) EAP-Message = 0x04080004 (8) Message-Authenticator = 0x00000000000000000000000000000000 Waking up in 2.8 seconds. (0) Cleaning up request packet ID 82 with timestamp +11 Waking up in 0.8 seconds. (1) Cleaning up request packet ID 83 with timestamp +11 (2) Cleaning up request packet ID 84 with timestamp +12 (3) Cleaning up request packet ID 85 with timestamp +12 (4) Cleaning up request packet ID 86 with timestamp +12 (5) Cleaning up request packet ID 87 with timestamp +12 (6) Cleaning up request packet ID 88 with timestamp +12 Waking up in 0.2 seconds. (7) Cleaning up request packet ID 89 with timestamp +12 (8) Cleaning up request packet ID 90 with timestamp +12 Ready to process requests

3 3

Re: User + Device Authentication to Specific Network
by Duncan X Simpson 12 Jun '19

12 Jun '19

On Jun 8, 2019, at 3:11 AM, Alan DeKok <aland(a)deployingradius.com> wrote: > That should be pretty simple. Put the MAC addresses into a database, and have FreeRADIUS check the database. > > if ("%{sql:SELECT MAC from known_macs WHERE MAC = %{Calling-Station-Id}") { > ... add to VLAN 2 ... > } > else { > ... add to VLAN 1 ... > } > > You'll have to create your own table, and do some more tests. But that's the basic idea. Thank you for the help! I seem to almost have it working, but I've run into one problem: Attributes don't seem to be expanding. I have the following in my post-auth section for testing: update reply { Unix-FTP-Shell := "%{Calling-Station-Id}" } Every time, Unix-FTP-Shell is set, but it's set to "": (22) # Executing section post-auth from file /etc/raddb/sites-enabled/inner-tunnel (22) post-auth { (22) update reply { (22) &Tunnel-Type := VLAN (22) &Tunnel-Medium-Type := IEEE-802 (22) } # update reply = noop (22) update reply { (22) EXPAND %{Calling-Station-Id} (22) --> (22) Unix-FTP-Shell := (22) } # update reply = noop I've swapped out Calling-Station-Id for a couple other things to test (Tunnel-Type (which I set about 3 lines up) and Service-Type (which came in with the request)), both with the same results. Why are these not getting expanded? Is post-auth the wrong place to do this?

2 5

Invalid vendor name in attribute name "0"
by Kyle Parrish 10 Jun '19

10 Jun '19

Hello, Seeking assistance troubleshooting the following error when running radiusd via Systemd. Error is: EXIT(1) CALLED src/main/mainconfig.c[955]. Last error was: Invalid vendor name in attribute name "0" Fresh install of FreeRADIUS 3.0.20. Compiled with "--localstatedir=/var --sysconfdir=/etc --with-rlm_sql_freetds --with-systemd" Operating System: Ubuntu 16.04.6 LTS Kernel: Linux 4.4.0-150-generic Architecture: x86-64 All configuration is default (aside from changing the user it is to run as to "Radiusd" in radiusd.conf). Running "radiusd -X" as root works as expected. Running "radiusd -X" as radiusd user manually works as expected. Only receive the error when running via Systemd. Systemd unit file is: [Unit] Description=FreeRADIUS multi-protocol policy server After=network-online.target Documentation=man:radiusd(8) man:radiusd.conf(5) http://wiki.freeradius.org/ http://networkradius.com/doc/ [Service] Type=notify WatchdogSec=60 NotifyAccess=all PIDFile=/var/run/radiusd/radiusd.pid EnvironmentFile=-/etc/default/radiusd # FreeRADIUS can do static evaluation of policy language rules based # on environmental variables which is very useful for doing per-host # customization. # Unfortunately systemd does not allow variable substitutions such # as %H or $(hostname) in the EnvironmentFile. # We provide HOSTNAME here for convenience. Environment=HOSTNAME=%H # Limit memory to 2G this is fine for %99.99 of deployments. FreeRADIUS # is not memory hungry, if it's using more than this, then there's probably # a leak somewhere. MemoryLimit=2G RuntimeDirectory=radiusd RuntimeDirectoryMode=0775 ExecStartPre=/usr/sbin/radiusd $FREERADIUS_OPTIONS -Cx -lstdout ExecStartPre=/bin/chown radiusd:radiusd /var/run/radiusd ExecStart=/usr/sbin/radiusd $FREERADIUS_OPTIONS Restart=on-failure RestartSec=5 # Don't elevate privileges after starting NoNewPrivileges=true # Allow binding to secure ports, broadcast addresses, and raw interfaces. CapabilityBoundingSet=CAP_NET_ADMIN CAP_NET_BIND_SERVICE CAP_NET_BROADCAST CAP_NET_RAW # Private /tmp that isn't shared by other processes PrivateTmp=true # cgroups are readable only by radiusd, and child processes ProtectControlGroups=true # don't load new kernel modules ProtectKernelModules=true # don't tune kernel parameters ProtectKernelTunables=true # Only allow native system calls SystemCallArchitectures=native # We shouldn't be writing to the configuration directory ReadOnlyDirectories=/etc/raddb/ # We can read and write to the log directory. ReadWriteDirectories=/var/log/radius/ [Install] WantedBy=multi-user.target Please let me know if there is any additional information that may help. Thank you. -- *Kyle Parrish* KyleParrish.com *living life to the fullest*

3 7

LDAP group checking stopping before the whole group list is checked
by Adam Bishop 10 Jun '19

10 Jun '19

I'm having an issue with ldap group checking where FreeRADIUS appears to bail out early if it encounters a group DN it can't resolve. The LDAP server (FreeIPA) has a very restrictive set of ACL's; the group which cannot be resolved (Replication Administrators) is not readable by standard accounts. I'd like to avoid messing with the ACL's, or granting FreeRADIUS more privileges if possible. If I run ldapsearch, the group I'm looking for is definitely in the memberOf list. Can I get it to continue reading the list of groups if it fails to resolve one, or is this intended (or something I've screwed up in the config)? Adam Bishop gpg: E75B 1F92 6407 DFDF 9F1C BF10 C993 2504 6609 D460 jisc.ac.uk --- # raddebug (3) Debug: Received Access-Request Id 154 from [1:2:3:4:5::6]:55794 to [1:2:3:4:5::7]:1812 length 93 (3) Debug: User-Name = "adam" (3) Debug: User-Password = "asdf" (3) Debug: NAS-Identifier = "esw-001" (3) Debug: Calling-Station-Id = "8.8.8.8" (3) Debug: NAS-IPv6-Address = 1:2:3:4:5::6 (3) Debug: # Executing section authorize from file /etc/raddb/sites-enabled/infrastructure (3) Debug: authorize { (3) Debug: update request { (3) Debug: } # update request = noop (3) Debug: ldap: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (3) Debug: ldap: --> (uid=adam) (3) Debug: ldap: Performing search in "cn=users,cn=accounts,dc=example,dc=org" with filter "(uid=adam)", scope "sub" (3) Debug: ldap: Waiting for search result... (3) Debug: ldap: User object found at DN "uid=adam,cn=users,cn=accounts,dc=example,dc=org" (3) Debug: ldap: Processing user attributes (3) Debug: [ldap] = ok (3) Debug: if ((ok || updated) && User-Password) { (3) Debug: if ((ok || updated) && User-Password) -> TRUE (3) Debug: if ((ok || updated) && User-Password) { (3) Debug: update { (3) Debug: } # update = noop (3) Debug: } # if ((ok || updated) && User-Password) = noop (3) Debug: if (&LDAP-Group[*] == "%{client:ldap_group}") { (3) Debug: EXPAND %{client:ldap_group} (3) Debug: --> switching-admins (3) Debug: Searching for user in group "switching-admins" (3) Debug: Using user DN from request "uid=adam,cn=users,cn=accounts,dc=example,dc=org" (3) Debug: Checking user object's memberOf attributes (3) Debug: Performing unfiltered search in "uid=adam,cn=users,cn=accounts,dc=example,dc=org", scope "base" (3) Debug: Waiting for search result... (3) Debug: Processing memberOf value "cn=servicea-admins,cn=groups,cn=accounts,dc=example,dc=org" as a DN (3) Debug: Resolving group DN "cn=servicea-admins,cn=groups,cn=accounts,dc=example,dc=org" to group name (3) Debug: Performing unfiltered search in "cn=servicea-admins,cn=groups,cn=accounts,dc=example,dc=org", scope "base" (3) Debug: Waiting for search result... (3) Debug: Group DN "cn=servicea-admins,cn=groups,cn=accounts,dc=example,dc=org" resolves to name "servicea-admins" (3) Debug: Processing memberOf value "cn=serviceb-admins,cn=groups,cn=accounts,dc=example,dc=org" as a DN (3) Debug: Resolving group DN "cn=serviceb-admins,cn=groups,cn=accounts,dc=example,dc=org" to group name (3) Debug: Performing unfiltered search in "cn=serviceb-admins,cn=groups,cn=accounts,dc=example,dc=org", scope "base" (3) Debug: Waiting for search result... (3) Debug: Group DN "cn=serviceb-admins,cn=groups,cn=accounts,dc=example,dc=org" resolves to name "serviceb-admins" <snip 10+ other groups> (3) Debug: Processing memberOf value "cn=Replication Administrators,cn=privileges,cn=pbac,dc=example,dc=org" as a DN (3) Debug: Resolving group DN "cn=Replication Administrators,cn=privileges,cn=pbac,dc=example,dc=org" to group name (3) Debug: Performing unfiltered search in "cn=Replication Administrators,cn=privileges,cn=pbac,dc=example,dc=org", scope "base" (3) Debug: Waiting for search result... (3) Debug: Search returned no results (3) ERROR: Group DN "cn=Replication Administrators,cn=privileges,cn=pbac,dc=example,dc=org" did not resolve to an object (3) Debug: User is not a member of "switching-admins" (3) Debug: if (&LDAP-Group[*] == "%{client:ldap_group}") -> FALSE (3) Debug: else { (3) Debug: update reply { (3) Debug: } # update reply = noop (3) Debug: [reject] = reject (3) Debug: } # else = reject (3) Debug: } # authorize = reject (3) Debug: Using Post-Auth-Type Reject (3) Debug: # Executing group from file /etc/raddb/sites-enabled/infrastructure (3) Debug: Post-Auth-Type REJECT { (3) Debug: attr_filter.access_reject: EXPAND %{User-Name} (3) Debug: attr_filter.access_reject: --> adam (3) Debug: attr_filter.access_reject: Matched entry DEFAULT at line 11 (3) Debug: [attr_filter.access_reject] = updated (3) Debug: [eap] = noop (3) Debug: rp_log: EXPAND rp_log.%{%{reply:Packet-Type}:-format} (3) Debug: rp_log: --> rp_log.Access-Reject (3) Debug: rp_log: EXPAND radiusd-rp-log#DOMAIN=VIRT#LOCATION=ATL#SERVICE=%{%{Service-Class}:-NONE}#ORG=%{%{request:operator-name}:-%{request:Stripped-User-Domain}}#USER=%{User-Name}#CSI=%{Calling-Station-Id}#NAS=%{Called-Station-Id}#CUI=%{reply:Chargeable-User-Identity}#RESULT=FAIL#VLAN=%{%{reply:Tunnel-Private-Group-ID}:-NONE}#CLIENT=%{client:shortname}#REPLY_MESSAGE=%{%{reply:reply-message}:-NONE}#MODULE_MESSAGE=%{%{%{request:Module-Failure-Message}:-%{session-state:Module-Failure-Message}}:-NONE}# (3) Mon Jun 10 01:17:34 2019: Debug: rp_log: --> radiusd-rp-log#DOMAIN=VIRT#LOCATION=ATL#SERVICE=infrastructure#ORG=#USER=adam#CSI=8.8.8.8#NAS=#CUI=#RESULT=FAIL#VLAN=NONE#CLIENT=esw-001.inf#REPLY_MESSAGE=Not Authorised#MODULE_MESSAGE=Group DN "cn=Replication Administrators,cn=privileges,cn=pbac,dc=example,dc=org" did not resolve to an object# (3) Debug: [rp_log] = ok (3) Debug: policy remove_reply_message_if_eap { (3) Debug: if (&reply:EAP-Message && &reply:Reply-Message) { (3) Debug: if (&reply:EAP-Message && &reply:Reply-Message) -> FALSE (3) Debug: else { (3) Debug: [noop] = noop (3) Debug: } # else = noop (3) Debug: } # policy remove_reply_message_if_eap = noop (3) Debug: } # Post-Auth-Type REJECT = updated (3) Debug: Delaying response for 1.000000 seconds (3) Debug: Sending delayed response (3) Debug: Sent Access-Reject Id 154 from [1:2:3:4:5::7]:1812 to [1:2:3:4:5::6]:55794 length 36 (3) Debug: Reply-Message := "Not Authorised" (3) Debug: Cleaning up request packet ID 154 with timestamp +1036 Jisc is a registered charity (number 1149740) and a company limited by guarantee which is registered in England under Company No. 5747339, VAT No. GB 197 0632 86. Jisc’s registered office is: One Castlepark, Tower Hill, Bristol, BS2 0JA. T 0203 697 5800. Jisc Services Limited is a wholly owned Jisc subsidiary and a company limited by guarantee which is registered in England under company number 2881024, VAT number GB 197 0632 86. The registered office is: One Castle Park, Tower Hill, Bristol BS2 0JA. T 0203 697 5800.

3 2

Re: Re: Data convertion and pre-defined variables for Dhcp site.
by CpServiceSPb 10 Jun '19

10 Jun '19

> Because DHCP-SIP-Servers-DHCP-Option is an "octets" data type, so you have to feed it octets. e.g. > &DHCP-SIP-Servers-DHCP-Option = 0x01c0a800fe > That will work. >* Dhcpdump shows: *> >* OPTION: 120 ( 12) SIP Servers DHCP Option *3131302e31302e302e323534* *> Because you gave the attribute a text string. Which isn't hex, and it isn't an IP address. But option 43 - DHCP-Vendor is octet also. However &DHCP-Vendor = "http://user:pass@%{listen:src_ipaddr}/pbx" works fine. > You just typed it there. You can add that as hex to the "update" statement. >* I specified this option at isc-dhcp-server simply *>* *option sip-pbx-servers 1 192.168.0.254;* *> That's nice for them. I added it &DHCP-SIP-Servers-DHCP-Option = "0x01c0a800fe" to update section. If you talked about it. But it would be easy that it is in human readable/clear format. > That's unfortunately more difficult to do in FreeRADIUS. Your best bet is to just use hex. Is there string to hex convertion ? Look like %{hex:%{listen:str_ipaddr}} ? But what about your previous words: > I looked into a lot of docs but didn' t find any success resolution. > So, how is the best way at unlang to: > - convert ipaddr type to octet; > - convert string to octet; > - convert string to ipaddr ? > You don't. The server should automatically do this. As I understood, in case of 120 option conversion in particular is made automatically, is it ?

2 3

Conditional variable references
by Adam Bishop 10 Jun '19

10 Jun '19

I store some settings like the redis password, and localhost shared secrets as variables, i.e.: ldap { ... identity = ${bind_dn} ... } as I'm running a single set of configuration shared across 3 different sets of servers, with a file called 'variables' generated by puppet that contains the instance specific settings. Is there any way to have a default value for these kinds of variables so I don't have to populate unused ones with dummy values? Or to have the server ignore missing variable references? I tried instantiating the variables as empty strings, then redefining them like: # cat /etc/raddb/radius.conf ... $INCLUDE defaults $INCLUDE variables ... # cat /etc/raddb/defaults ... bind_dn = "" # cat /etc/raddb/variables ... bind_dn = "dc=jisc,dc=ac,dc=uk" Which loaded without error, but returned an empty string. Adam Bishop gpg: E75B 1F92 6407 DFDF 9F1C BF10 C993 2504 6609 D460 jisc.ac.uk Jisc is a registered charity (number 1149740) and a company limited by guarantee which is registered in England under Company No. 5747339, VAT No. GB 197 0632 86. Jisc’s registered office is: One Castlepark, Tower Hill, Bristol, BS2 0JA. T 0203 697 5800. Jisc Services Limited is a wholly owned Jisc subsidiary and a company limited by guarantee which is registered in England under company number 2881024, VAT number GB 197 0632 86. The registered office is: One Castle Park, Tower Hill, Bristol BS2 0JA. T 0203 697 5800.

2 2

Can I gracefully handle radius requests if all home servers are down?
by work vlpl 10 Jun '19

10 Jun '19

Hello, Is it possible to detect that home server is not available and gracefully process radius request locally? I tried to use `Post-Proxy-Type Fail-Authentication {}` section but it seems that FreeRadius server will not expect ``` update control { Auth-Type := Accept } ``` instruction in that section and reject request. This is a fragment from debug log ``` (30) Post-Proxy-Type Fail-Authentication { (30) update reply { (30) Tunnel-Type := VLAN (30) Tunnel-Medium-Type := IEEE-802 (30) Tunnel-Private-Group-id := 333 (30) Idle-Timeout := 1800 (30) } # update reply = noop (30) update control { (30) Auth-Type := Accept (30) } # update control = noop (30) } # Post-Proxy-Type Fail-Authentication = noop (30) There was no response configured: rejecting request (30) Using Post-Auth-Type Reject ``` -- Vladimir

3 6

Port/mac/IP authentication, authorization, auditing. Is it possible ?
by CpServiceSPb 09 Jun '19

09 Jun '19

Is it possible by default or by using additional modules to authentice, authorize devices plugged to managed switch not only by mac, btu also by mac/ip or port/mac/ip, especially for statically assigned devices ?

3 8

Data convertion and pre-defined variables for Dhcp site.
by CpServiceSPb 09 Jun '19

09 Jun '19

I try to set up Dhcp Option 120 - freeradius DHCP-SIP-Servers-DHCP-Option and Dhcp Option 43 - DHCP-Vendor using unlang, both are octet type. But is still faulted. I looked into a lot of docs but didn' t find any success resolution. So, how is the best way at unlang to: - convert ipaddr type to octet; - convert string to octet; - convert string to ipaddr ? I tried to use %{hex:192.168.0.254} and %{ipaddr: 192.168.0.254} but there is nothing. Also, I investigate that %{listen:src_ipaddr} is possible to use as some of pre-defined variable with Dcp IP. But its type is string. Also I tried %{hex: :%{listen:src_ipaddr}} and %{ipaddr:%{listen:src_ipaddr}} , there is no positive result. So, is there predefined variables, providing for example IP of Dhcp which I can use anywhere instead of specifying of 192.168.0.254 directly ? For example &DHCP-Domain-Name-Server += %{ipaddr:&some_variable}

2 3