- Freeradius-Users - lists.freeradius.org

Ippool giving gateway addresses
by Alejandro Gandara 17 Oct '11

17 Oct '11

Hi List, I have two doubts which I couldn't resolv properly. I'll be so pleased if someone could give me a hand. 1º There is any way to configure ippool to give a gateway for each configured pool? 2º How I could check the bind addresses in db.* files? 3º Radiuis-Framed-Routing is used to configure a gateway for each profile? Thanks for your time and your patience.

2 4

RE: EAP Testing - Newbie
by Tim Sylvester 17 Oct '11

17 Oct '11

> Thanks for your prompt response. eapol_test has been built with all EAP > modules. See log below: > > Do you know what the problem can be? I've tried almost everything now! It's hard to tell what's going on with only a portion of the log. Send the logs for both eapol_test and FreeRADIUS in debug mode. Send it to the list. It's better to have multiple people look at the problem. Tim > > Thanks again. > > Sergio. > > > --- o --- > > eapol_test -c md5.conf -s testing123 > > > Reading configuration file 'md5.conf' > Line: 1 - start of a new network block > ssid - hexdump_ascii(len=7): > 45 78 61 6d 70 6c 65 Example > eap methods - hexdump(len=16): 00 00 00 00 0d 00 00 00 00 00 00 00 00 00 00 > 00 > eapol_flags=0 (0x0) > key_mgmt: 0x1 > identity - hexdump_ascii(len=8): > 74 65 73 74 75 73 65 72 testuser > password - hexdump_ascii(len=6): > 74 65 73 74 70 77 testpw > ca_cert - hexdump_ascii(len=40): > 63 3a 2f 46 72 65 65 52 41 44 49 55 53 2f 65 74 c:/FreeRADIUS/et > 63 2f 72 61 64 64 62 2f 63 65 72 74 73 2f 52 6f c/raddb/certs/Ro > 6f 74 43 41 2e 70 65 6d otCA.pem > client_cert - hexdump_ascii(len=38): > 63 3a 2f 46 72 65 65 52 41 44 49 55 53 2f 65 74 c:/FreeRADIUS/et > 63 2f 72 61 64 64 62 2f 63 65 72 74 73 2f 75 73 c/raddb/certs/us > 65 72 2e 64 65 72 er.der > private_key - hexdump_ascii(len=42): > 63 3a 2f 46 72 65 65 52 41 44 49 55 53 2f 65 74 c:/FreeRADIUS/et > 63 2f 72 61 64 64 62 2f 63 65 72 74 73 2f 75 73 c/raddb/certs/us > 65 72 2d 6b 65 79 2e 64 65 72 er-key.der > phase2 - hexdump_ascii(len=11): > 61 75 74 68 65 61 70 3d 4d 44 35 autheap=MD5 > anonymous_identity - hexdump_ascii(len=9): > 61 6e 6f 6e 79 6d 6f 75 73 anonymous > Priority group 0 > id=0 ssid='Example' > Authentication server 127.0.0.1:1812 > EAPOL: SUPP_PAE entering state DISCONNECTED > EAPOL: KEY_RX entering state NO_KEY_RECEIVE > EAPOL: SUPP_BE entering state INITIALIZE > EAP: EAP entering state DISABLED > EAPOL: External notification - portValid=0 > EAPOL: External notification - portEnabled=1 > EAPOL: SUPP_PAE entering state CONNECTING > EAPOL: SUPP_BE entering state IDLE > EAP: EAP entering state INITIALIZE > EAP: EAP entering state IDLE > CTRL_IFACE - test - wait for monitor > Sending fake EAP-Request-Identity > EAPOL: Received EAP-Packet frame > EAPOL: SUPP_PAE entering state RESTART > EAP: EAP entering state INITIALIZE > EAP: EAP entering state IDLE > EAPOL: SUPP_PAE entering state AUTHENTICATING > EAPOL: SUPP_BE entering state REQUEST > EAPOL: getSuppRsp > EAP: EAP entering state RECEIVED > EAP: Received EAP-Request id=0 method=1 vendor=0 vendorMethod=0 > EAP: EAP entering state IDENTITY > CTRL-EVENT-EAP-STARTED EAP authentication started > EAP: EAP-Request Identity data - hexdump_ascii(len=0): > EAP: using anonymous identity - hexdump_ascii(len=9): > 61 6e 6f 6e 79 6d 6f 75 73 anonymous > EAP: EAP entering state SEND_RESPONSE > EAP: EAP entering state IDLE > EAPOL: SUPP_BE entering state RESPONSE > EAPOL: txSuppRsp > WPA: eapol_test_eapol_send(type=0 len=14) TX EAP -> RADIUS - > hexdump(len=14): 02 00 00 0e 01 61 6e 6f 6e 79 6d 6f 75 73 Encapsulating EAP > message into a RADIUS packet Learned identity from EAP-Response-Identity > - hexdump(len=9): 61 6e 6f 6e 79 6d 6f 75 73 Sending RADIUS message to > authentication server RADIUS message: code=1 (Access-Request) > identifier=0 length=126 > Attribute 1 (User-Name) length=11 > Value: 'anonymous' > Attribute 4 (NAS-IP-Address) length=6 > Value: 127.0.0.1 > Attribute 31 (Calling-Station-Id) length=19 > Value: '02-00-00-00-00-01' > Attribute 12 (Framed-MTU) length=6 > Value: 1400 > Attribute 61 (NAS-Port-Type) length=6 > Value: 19 > Attribute 77 (Connect-Info) length=24 > Value: 'CONNECT 11Mbps 802.11b' > Attribute 79 (EAP-Message) length=16 > Value: 02 00 00 0e 01 61 6e 6f 6e 79 6d 6f 75 73 > Attribute 80 (Message-Authenticator) length=18 > Value: 29 8c 2f d2 bc e7 e4 4f 38 ff 02 28 4f 38 f5 61 Next RADIUS client > retransmit in 3 seconds > > EAPOL: SUPP_BE entering state RECEIVE > Received 64 bytes from RADIUS server > Received RADIUS message > RADIUS message: code=11 (Access-Challenge) identifier=0 length=64 > Attribute 79 (EAP-Message) length=8 > Value: 01 01 00 06 0d 20 > Attribute 80 (Message-Authenticator) length=18 > Value: ca c5 9f c8 7c a3 4f 44 0a ab b1 3b f2 7c 1f 17 > Attribute 24 (State) length=18 > Value: 6d 9b 65 d3 6d 9a 68 84 2b 53 ce 97 ac 1c e2 81 STA 02:00:00:00:00:01: > Received RADIUS packet matched with a pending request, round trip time > 0.00 sec > > RADIUS packet matching with station > decapsulated EAP packet (code=1 id=1 len=6) from RADIUS server: EAP- > Request-TLS (13) > EAPOL: Received EAP-Packet frame > EAPOL: SUPP_BE entering state REQUEST > EAPOL: getSuppRsp > EAP: EAP entering state RECEIVED > EAP: Received EAP-Request id=1 method=13 vendor=0 vendorMethod=0 > EAP: EAP entering state GET_METHOD > CTRL-EVENT-EAP-PROPOSED-METHOD vendor=0 method=13 > EAP: Initialize selected EAP method: vendor 0 method 13 (TLS) > TLS: using phase1 config options > TLS: Trusted root certificate(s) loaded > OpenSSL: SSL_use_certificate_file (DER) --> OK > OpenSSL: SSL_use_PrivateKey_File (DER) --> OK > SSL: Private key loaded successfully > CTRL-EVENT-EAP-METHOD EAP vendor 0 method 13 (TLS) selected > EAP: EAP entering state METHOD > SSL: Received packet(len=6) - Flags 0x20 > EAP-TLS: Start > SSL: (where=0x10 ret=0x1) > SSL: (where=0x1001 ret=0x1) > SSL: SSL_connect:before/connect initialization > SSL: (where=0x1001 ret=0x1) > SSL: SSL_connect:SSLv3 write client hello A > SSL: (where=0x1002 ret=0xffffffff) > SSL: SSL_connect:error in SSLv3 read server hello A > SSL: SSL_connect - want more data > SSL: 210 bytes pending from ssl_out > SSL: 210 bytes left to be sent out (of total 210 bytes) > EAP: method process -> ignore=FALSE methodState=MAY_CONT > decision=FAIL > EAP: EAP entering state SEND_RESPONSE > EAP: EAP entering state IDLE > EAPOL: SUPP_BE entering state RESPONSE > EAPOL: txSuppRsp > WPA: eapol_test_eapol_send(type=0 len=216) TX EAP -> RADIUS - > hexdump(len=216): 02 01 00 d8 0d 00 16 03 01 00 cd 01 00 00 c9 03 01 4e 9b 60 > 82 ce 26 51 18 1a 0f fd 61 c0 4c 56 44 2e a2 ed da d9 cd 0b a9 3f f4 97 dd 76 0a > 58 be 00 00 5c c0 14 c0 0a 00 39 00 38 00 88 00 87 c0 0f c0 05 00 35 00 84 c0 12 c0 > 08 00 16 00 13 c0 0d c0 03 00 0a c0 13 c0 09 00 33 00 32 00 9a 00 99 00 45 00 44 c0 > 0e c0 04 00 2f 00 96 00 41 00 07 c0 11 c0 07 c0 0c c0 02 00 05 00 04 00 15 00 12 00 > 09 00 14 00 11 00 08 00 06 00 03 00 ff 01 00 00 44 00 0b 00 04 03 00 01 02 00 0a 00 > 34 00 32 00 01 00 02 00 03 00 04 00 05 00 06 00 07 00 08 00 09 00 0a 00 0b 00 0c > 00 0d 00 0e 00 0f 00 10 00 11 00 12 00 13 00 14 00 15 00 16 00 17 00 18 00 19 00 > 23 00 00 Encapsulating EAP message into a RADIUS packet > Copied RADIUS State Attribute > Sending RADIUS message to authentication server RADIUS message: code=1 > (Access-Request) identifier=1 length=346 > Attribute 1 (User-Name) length=11 > Value: 'anonymous' > Attribute 4 (NAS-IP-Address) length=6 > Value: 127.0.0.1 > Attribute 31 (Calling-Station-Id) length=19 > Value: '02-00-00-00-00-01' > Attribute 12 (Framed-MTU) length=6 > Value: 1400 > Attribute 61 (NAS-Port-Type) length=6 > Value: 19 > Attribute 77 (Connect-Info) length=24 > Value: 'CONNECT 11Mbps 802.11b' > Attribute 79 (EAP-Message) length=218 > Value: 02 01 00 d8 0d 00 16 03 01 00 cd 01 00 00 c9 03 01 4e 9b 60 82 ce 26 51 > 18 1a 0f fd 61 c0 4c 56 44 2e a2 ed da d9 cd 0b a9 3f f4 97 dd 76 0a 58 be 00 00 > 5c c0 14 c0 0a 00 39 00 38 00 88 00 87 c0 0f c0 05 00 35 00 84 c0 12 c0 08 00 16 00 > 13 c0 0d c0 03 00 0a c0 13 c0 09 00 33 00 32 00 9a 00 99 00 45 00 44 c0 0e c0 04 00 > 2f 00 96 00 41 00 07 c0 11 c0 07 c0 0c c0 02 00 05 00 04 00 15 00 12 00 09 00 14 00 > 11 00 08 00 06 00 03 00 ff 01 00 00 44 00 0b 00 04 03 00 01 02 00 0a 00 34 00 32 00 > 01 00 02 00 03 00 04 00 05 00 06 00 07 00 08 00 09 00 0a 00 0b 00 0c 00 0d 00 0e > 00 0f 00 10 00 11 00 12 00 13 00 14 00 15 00 16 00 17 00 18 00 19 00 23 00 00 > Attribute 24 (State) length=18 > Value: 6d 9b 65 d3 6d 9a 68 84 2b 53 ce 97 ac 1c e2 81 > Attribute 80 (Message-Authenticator) length=18 > Value: 9e c4 a4 f0 55 8c 2a 18 4e 44 ee 10 2d 97 5d 0d Next RADIUS client > retransmit in 3 seconds > > EAPOL: SUPP_BE entering state RECEIVE > Received 1090 bytes from RADIUS server > Received RADIUS message > RADIUS message: code=11 (Access-Challenge) identifier=1 length=1090 > Attribute 79 (EAP-Message) length=255 > Value: 01 02 04 00 0d c0 00 00 0e af 16 03 01 00 31 02 00 00 2d 03 01 4e 9b 60 > 82 70 e6 76 5a ef e2 e5 37 6c d6 08 dd ee 9f b6 70 66 d2 df a8 0e 1f 2c e8 33 f3 > 07 f5 00 00 39 00 00 05 ff 01 00 01 00 16 03 01 0b eb 0b 00 0b e7 00 0b e4 00 06 > 5f 30 82 06 5b 30 82 05 43 a0 03 02 01 02 02 01 02 30 0d 06 09 2a 86 48 86 f7 0d > 01 01 05 05 00 30 81 dd 31 0b 30 09 06 03 55 04 06 13 02 47 42 31 0f 30 0d 06 03 > 55 04 08 13 06 4c 6f 6e 64 6f 6e 31 14 30 12 06 03 55 04 07 13 0b 57 65 73 74 6d > 69 6e 73 74 65 72 31 1c 30 1a 06 03 55 04 0a 13 13 4d 61 74 65 41 52 20 49 54 20 > 53 6f 6c 75 74 69 6f 6e 73 31 17 30 15 06 03 55 04 0b 13 0e 50 4b 49 20 44 65 70 > 61 72 74 6d 65 6e 74 31 22 30 20 06 03 55 04 03 13 19 54 65 73 74 20 52 6f 6f 74 > 20 43 41 20 28 46 72 65 65 52 41 44 49 > Attribute 79 (EAP-Message) length=255 > Value: 55 53 29 31 20 30 1e 06 03 55 04 0d 13 17 54 65 73 74 20 52 6f 6f 74 43 > 41 20 43 65 72 74 69 66 69 63 61 74 65 31 1d 30 1b 06 09 2a 86 48 86 f7 0d 01 09 > 01 16 0e 69 6e 66 6f 40 6d 61 74 65 61 72 2e 65 75 31 0b 30 09 06 03 55 04 05 13 > 02 30 31 30 1e 17 0d 31 31 31 30 31 36 31 34 32 37 35 32 5a 17 0d 31 32 31 30 31 > 35 31 34 32 37 35 32 5a 30 81 f2 31 23 30 21 06 03 55 04 03 13 1a 55 4b 57 49 4e > 32 30 30 38 52 32 2e 63 6f 72 70 2e 6d 61 74 65 61 72 2e 65 75 31 12 30 10 06 0a > 09 92 26 89 93 f2 2c 64 01 19 16 02 45 55 31 1d 30 1b 06 09 2a 86 48 86 f7 0d 01 > 09 01 16 0e 69 6e 66 6f 40 6d 61 74 65 61 72 2e 65 75 31 0b 30 09 06 03 55 04 06 > 13 02 47 42 31 0f 30 0d 06 03 55 04 08 13 06 4c 6f 6e 64 6f 6e 31 14 30 12 06 03 55 > 04 07 13 0b 57 65 73 74 6d 69 6e 73 > Attribute 79 (EAP-Message) length=255 > Value: 74 65 72 31 16 30 14 06 03 55 04 0b 13 0d 49 54 20 44 65 70 61 72 74 6d > 65 6e 74 31 16 30 14 06 03 55 04 05 13 0d 55 4b 4c 4f 4e 44 4f 4e 53 52 56 30 31 > 31 34 30 32 06 03 55 04 0d 13 2b 54 65 73 74 20 53 65 72 76 65 72 20 43 65 72 74 > 69 66 69 63 61 74 65 20 28 50 45 41 50 20 2d 20 46 72 65 65 52 41 44 49 55 53 29 > 30 81 9f 30 0d 06 09 2a 86 48 86 f7 0d 01 01 01 05 00 03 81 8d 00 30 81 89 02 81 > 81 00 d0 91 2b e9 29 81 af 2f 9e e8 e1 c8 27 c3 0b 70 a9 71 04 63 fb e0 52 bd e4 > 1c 7a 96 af 52 bc 77 0a 83 da a7 bb c2 86 da 3b ef f1 f7 f7 13 94 c8 06 f0 21 4b 2b > 1f ae 41 aa fb 04 5e fc 1e 49 b5 a7 00 82 fd 2e ac e9 f7 c0 98 db ea 77 7b 6b d8 > d6 d8 0c 99 d4 2a 2a 61 84 f7 63 75 68 38 fa ff 97 04 87 37 f9 2b db c4 1c d8 03 e1 > 2e d1 7c c4 cf ed 29 57 97 d6 f6 > Attribute 79 (EAP-Message) length=255 > Value: db 79 9f 5b bc 4b 53 ce 81 02 03 01 00 01 a3 82 02 91 30 82 02 8d 30 0f > 06 03 55 1d 13 01 01 ff 04 05 30 03 02 01 00 30 0e 06 03 55 1d 0f 01 01 ff 04 04 03 > 02 03 f8 30 1d 06 03 55 1d 0e 04 16 04 14 c7 c5 14 ad 16 23 77 01 f6 29 bf 2c 1d 18 > c2 4c 81 86 18 8f 30 82 01 0b 06 03 55 1d 23 04 82 01 02 30 81 ff 80 14 8c 04 28 72 > c8 60 3f 29 a5 8a c1 4f db 9a 62 ff 9a ad c3 fa a1 81 e3 a4 81 e0 30 81 dd 31 0b 30 > 09 06 03 55 04 06 13 02 47 42 31 0f 30 0d 06 03 55 04 08 13 06 4c 6f 6e 64 6f 6e 31 > 14 30 12 06 03 55 04 07 13 0b 57 65 73 74 6d 69 6e 73 74 65 72 31 1c 30 1a 06 03 > 55 04 0a 13 13 4d 61 74 65 41 52 20 49 54 20 53 6f 6c 75 74 69 6f 6e 73 31 17 30 15 > 06 03 55 04 0b 13 0e 50 4b 49 20 44 65 70 61 72 74 6d 65 6e 74 31 22 30 20 06 03 > 55 04 03 13 19 54 65 > Attribute 79 (EAP-Message) length=14 > Value: 73 74 20 52 6f 6f 74 20 43 41 20 28 > Attribute 80 (Message-Authenticator) length=18 > Value: eb 77 c8 8e ab 89 28 65 cf 6b ea d1 ce 32 b6 2e > Attribute 24 (State) length=18 > Value: 6d 9b 65 d3 6c 99 68 84 2b 53 ce 97 ac 1c e2 81 STA 02:00:00:00:00:01: > Received RADIUS packet matched with a pending request, round trip time > 0.00 sec > > RADIUS packet matching with station > decapsulated EAP packet (code=1 id=2 len=1024) from RADIUS server: EAP- > Request-TLS (13) > EAPOL: Received EAP-Packet frame > EAPOL: SUPP_BE entering state REQUEST > EAPOL: getSuppRsp > EAP: EAP entering state RECEIVED > EAP: Received EAP-Request id=2 method=13 vendor=0 vendorMethod=0 > EAP: EAP entering state METHOD > SSL: Received packet(len=1024) - Flags 0xc0 > SSL: TLS Message Length: 3759 > SSL: Need 2745 bytes more input data > SSL: Building ACK (type=13 id=2 ver=0) > EAP: method process -> ignore=FALSE methodState=MAY_CONT > decision=FAIL > EAP: EAP entering state SEND_RESPONSE > EAP: EAP entering state IDLE > EAPOL: SUPP_BE entering state RESPONSE > EAPOL: txSuppRsp > WPA: eapol_test_eapol_send(type=0 len=6) TX EAP -> RADIUS - > hexdump(len=6): 02 02 00 06 0d 00 Encapsulating EAP message into a RADIUS > packet > Copied RADIUS State Attribute > Sending RADIUS message to authentication server RADIUS message: code=1 > (Access-Request) identifier=2 length=136 > Attribute 1 (User-Name) length=11 > Value: 'anonymous' > Attribute 4 (NAS-IP-Address) length=6 > Value: 127.0.0.1 > Attribute 31 (Calling-Station-Id) length=19 > Value: '02-00-00-00-00-01' > Attribute 12 (Framed-MTU) length=6 > Value: 1400 > Attribute 61 (NAS-Port-Type) length=6 > Value: 19 > Attribute 77 (Connect-Info) length=24 > Value: 'CONNECT 11Mbps 802.11b' > Attribute 79 (EAP-Message) length=8 > Value: 02 02 00 06 0d 00 > Attribute 24 (State) length=18 > Value: 6d 9b 65 d3 6c 99 68 84 2b 53 ce 97 ac 1c e2 81 > Attribute 80 (Message-Authenticator) length=18 > Value: a9 7e 43 1c 85 51 4b 08 e5 45 69 b9 85 a6 a6 16 Next RADIUS client > retransmit in 3 seconds > > EAPOL: SUPP_BE entering state RECEIVE > EAPOL: startWhen --> 0 > STA 02:00:00:00:00:01: Resending RADIUS message (id=2) > > Next RADIUS client retransmit in 6 seconds STA 02:00:00:00:00:01: Resending > RADIUS message (id=2) > > Next RADIUS client retransmit in 12 seconds STA 02:00:00:00:00:01: > Resending RADIUS message (id=2) > > Next RADIUS client retransmit in 24 seconds EAPOL test timed out > EAPOL: EAP key not available > EAP: deinitialize previously used EAP method (13, TLS) at EAP deinit > ENGINE: engine deinit > MPPE keys OK: 0 mismatch: 0 > FAILURE > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > From: tim.sylvester(a)networkradius.com > > To: freeradius-users(a)lists.freeradius.org > > Subject: RE: EAP Testing - Newbie > > Date: Sun, 16 Oct 2011 12:37:20 -0700 > > > > > I'm in the process of testing FreeRADIUS 2.1.11, just basic/standard > > setup. > > > I've been following the following user guide: > > > http://deployingradius.com/documents/configuration/pap.html. Very > > > useful, by the way. > > > > > > PAP, MSCHAP and MSCHAPv2 work ok, but I'm unable to get any EAP > > > tests to pass. I've tries almost everything, including: > > > http://deployingradius.com/documents/configuration/eap- > problems.html > > > > > > radtest -t eap-md5 ....... (it works ok) > > > > > > > OK. The means the eap-md5 worked for radtest and FreeRADIUS. > > > > > --------- EAP-MD5 test --------- > > > > > > http://deployingradius.com/scripts/eapol_test/ > > > > > > > > > eapol_test.exe -c md5.conf -s testing123 ( it doesn't > > work!) > > > > OK. Since eap-md5 worked for FreeRADIUS and radeaptest above, but not > > for eapol_test and FreeRADIUS, this is most likely a problem with > > eapol_test not supporting eap-md5. > > > > > EAPOL: SUPP_BE entering state RECEIVE Received 80 bytes from RADIUS > > > server Received RADIUS message RADIUS message: code=11 > > > (Access-Challenge) identifier=0 length=80 Attribute 79 (EAP-Message) > > > length=24 > > > Value: 01 01 00 16 04 10 2d 5a 5e ca fd 46 31 37 33 67 ef 5f ec 14 > > 64 c3 > > > Attribute 80 (Message-Authenticator) length=18 > > > Value: 37 83 06 12 9c 7b 2d 98 9a e8 6b 81 79 03 ce 63 Attribute 24 > > > (State) length=18 > > > Value: cb 7a ce 96 cb 7b ca 0b 07 a3 2c 75 4a 0c c4 c6 STA > > 02:00:00:00:00:01: > > > Received RADIUS packet matched with a pending request, round trip > > > time > > > 0.00 sec > > > > > > RADIUS packet matching with station > > > decapsulated EAP packet (code=1 id=1 len=22) from RADIUS server: > > > EAP- > > > Request-MD5 (4) > > > > RADIUS Server proposed using eap-md5. > > > > > > > EAPOL: Received EAP-Packet frame > > > EAPOL: SUPP_BE entering state REQUEST > > > EAPOL: getSuppRsp > > > EAP: EAP entering state RECEIVED > > > EAP: Received EAP-Request id=1 method=4 vendor=0 vendorMethod=0 > > > EAP: EAP entering state GET_METHOD > > > EAP: configuration does not allow: vendor 0 method 4 > > > EAP: vendor 0 method 4 not allowed > > > > eapol_test said it's configuration does not support "method 4" (aka > > eap-md5). > > > > > > > CTRL-EVENT-EAP-PROPOSED-METHOD vendor=0 method=4 -> NAK > > > EAP: Building EAP-Nak (requested type 4 vendor=0 method=0 not > > > allowed) > > > EAP: allowed methods - hexdump(len=1): 15 > > > EAP: EAP entering state SEND_RESPONSE > > > > eapol_test sends a NAK back to the FreeRADIUS because it does not > > support > > eap-md5 (or any other eap method sent back by FR). > > > > Verify that eapol_test was successfully built with support for > > eap-md5. Look for error messages during the build process. You will > > probably see error messages saying that it could not find the OpenSSL > libraries and/or headers. > > > > Tim > > > > - > > List info/subscribe/unsubscribe? See > > http://www.freeradius.org/list/users.html

3 4

how to configure
by Harish Mandowara 17 Oct '11

17 Oct '11

Dear all, How to configure freeradius server with netgear WNR3500L access point with these three entities. Authentication server (Freeradius)----- Access Pint(Netgear)--------Mobile Terminal (My PC). -- Warm Regards Harish Mandowara -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean.

1 0

How to Determine Whether an Attribute is a Check Item or Reply Item
by Det Det 16 Oct '11

16 Oct '11

Hi there, how to find out whether the attribute is a check/reply attribute? thanks! det

4 5

Re: FreeRadius with Eduroam - Accounting
by Mike Diggins 16 Oct '11

16 Oct '11

On Tue, 4 Oct 2011, Mike Diggins wrote: > > I'm running FreeRadius 2.1.3 on RedHat Enterprise Linux configured as an > Eduroam Radius proxy server. My Cisco Wireless Lan Controllers are constantly > failing over the Accounting Servers, due to lack of response from the Home > Servers, or so says the log. However, I believe the issue is that some remote > institutions Radius Servers are ignoring the Accounting packets, and timing > out my end, making it believe the Home Servers have failed to respond. > FreeRadius responds by marking the Home server dead. It then sends a > status-server query, to which is gets a reply, and enables the Dead Home > server. I believe that's the sequence of events anyway. I captured some of > that in debug mode: > > Rejecting request 288 due to lack of any response from home server x.x.x.x > port 1813 > > Finished request 288. > > Cleaning up request 288 ID 205 with timestamp +1161 > > PROXY: Marking home server x.x.x.x port 1813 as zombie (it looks like it is > dead). > > Sending Status-Server of id 55 to x.x.x.x port 1813 > Message-Authenticator := 0x00000000000000000000000000000000 > NAS-Identifier := "Status Check. Are you alive?" > Waking up in 3.9 seconds. > > rad_recv: Access-Accept packet from host x.x.x.x port 1813, id=55, length=806 > > I don't have any control over Accounting Packets being accepted, or not, by > other Eduroam members. Some do, some don't I imagine. Is there a > configuration for FreeRadius that handles this situation cleanly? Seems to me > that FR should check the Home server first, before marking it dead (at > least). Accounting feature on the WLAN controllers (for now), I noticed that a similar failure is a happening on the Authentication side. Some authentication requests proxied to other radius servers (via Eduroam) are either failing or taking a long time to respond, which also causes my FreeRadius to mark the Home Server as DOWN. That also seems to cause a chain reaction of backed up requests, causing my WLAN controllers to failover the radius server. So, similar to my Accounting problem, is there anyway to prevent a single Authentication failure from backing up the works!? Does FR answer queries in sequence only? I don't really understand why this sort of failure has such a nasty consequence. -Mike

3 5

Policy construct for string "concatenation"
by Ray Scholl 15 Oct '11

15 Oct '11

Good afternoon: I was hoping to see if anyone could provide the best syntax to concatenate two strings being used in a comparison (policy.conf). Synopsis: We intend to compare an LDAP group name to a Freeradius shortname, but we want the shortname to be "shortname" ++ "otp". The existing syntax (which we believe will work) is : if ( clients_ldap-Ldap-Group == FreeRadius-Client-Shortname) New syntax : if ( clients_ldap-Ldap-Group == ) The Manpage for unlang references double quotes around variable, but one is a constant. Should I declare a variable and then quote them - "FreeRadius-Client-Shortname vOTP" Thanks in advance, Ray

4 7

(no subject)
by OzSpots - Carl Sawers 15 Oct '11

15 Oct '11

Hi All, I have searched high and low for a Radacct Terminate cause description for Freeradius, the terminate cause states "Lost-Session" , anyone know what it refers too? Regards Carl

3 2

Re: Newbie starting up - with problem, of course; and questions
by Dale Grice 14 Oct '11

14 Oct '11

>> I am running freeradius 2.1.10 on Debian 6.0.3. >> >> What startup script in Debian starts freeradius? I would like to add the >> -X option to it. >> >> My first problem is I can't get radtest to work. The only thing I have >> modified is the User file. I searched the FAQs and maillist archives to no >> avail. >> >> Top lines in User file: >> bob Cleartext-Password := "hello" >> Reply-Message = "Hello, BOB" >> testing Cleartext-Password := "password" >> Reply-Message = "Testing in Progress" >> # >> >> My radtest: >> root@Mikado:/etc/freeradius# radtest bob hello localhost 0 testing123 >> Sending Access-Request of id 171 to 127.0.0.1 port 1812 >> User-Name = "bob" >> User-Password = "hello" >> NAS-IP-Address = 10.56.1.11 >> NAS-Port = 0 >> radclient: Failed to send packet for ID 171: (unknown error) >> Sending Access-Request of id 171 to 127.0.0.1 port 1812 >> User-Name = "bob" >> User-Password = "hello" >> NAS-IP-Address = 10.56.1.11 >> NAS-Port = 0 >> radclient: Failed to send packet for ID 171: (unknown error) >> Sending Access-Request of id 171 to 127.0.0.1 port 1812 >> User-Name = "bob" >> User-Password = "hello" >> NAS-IP-Address = 10.56.1.11 >> NAS-Port = 0 >> radclient: Failed to send packet for ID 171: (unknown error) >> radclient: no response from server for ID 171 socket 3 >> >> >> Debug output: >> >> FreeRADIUS Version 2.1.10, for host i486-pc-kfreebsd-gnu, built on Nov 15 >> 2010 at 09:02:02 >> Copyright (C) 1999-2009 The FreeRADIUS server project and contributors. >> There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A >> PARTICULAR PURPOSE. >> You may redistribute copies of FreeRADIUS under the terms of the >> GNU General Public License v2. >> Starting - reading configuration files ... >> including configuration file /etc/freeradius/radiusd.conf >> including configuration file /etc/freeradius/proxy.conf >> including configuration file /etc/freeradius/clients.conf >> including files in directory /etc/freeradius/modules/ >> including configuration file /etc/freeradius/modules/always >> including configuration file /etc/freeradius/modules/attr_filter >> including configuration file /etc/freeradius/modules/attr_rewrite >> including configuration file /etc/freeradius/modules/chap >> including configuration file /etc/freeradius/modules/checkval >> including configuration file /etc/freeradius/modules/counter >> including configuration file /etc/freeradius/modules/cui >> including configuration file /etc/freeradius/modules/detail >> including configuration file /etc/freeradius/modules/detail.example.com >> including configuration file /etc/freeradius/modules/detail.log >> including configuration file /etc/freeradius/modules/digest >> including configuration file /etc/freeradius/modules/dynamic_clients >> including configuration file /etc/freeradius/modules/echo >> including configuration file /etc/freeradius/modules/etc_group >> including configuration file /etc/freeradius/modules/exec >> including configuration file /etc/freeradius/modules/expiration >> including configuration file /etc/freeradius/modules/expr >> including configuration file /etc/freeradius/modules/files >> including configuration file /etc/freeradius/modules/inner-eap >> including configuration file /etc/freeradius/modules/ippool >> including configuration file /etc/freeradius/modules/krb5 >> including configuration file /etc/freeradius/modules/ldap >> including configuration file /etc/freeradius/modules/linelog >> including configuration file /etc/freeradius/modules/logintime >> including configuration file /etc/freeradius/modules/mac2ip >> including configuration file /etc/freeradius/modules/mschap >> including configuration file /etc/freeradius/modules/mac2vlan >> including configuration file /etc/freeradius/modules/ntlm_auth >> including configuration file /etc/freeradius/modules/opendirectory >> including configuration file /etc/freeradius/modules/otp >> including configuration file /etc/freeradius/modules/pam >> including configuration file /etc/freeradius/modules/pap >> including configuration file /etc/freeradius/modules/passwd >> including configuration file /etc/freeradius/modules/perl >> including configuration file /etc/freeradius/modules/policy >> including configuration file /etc/freeradius/modules/preprocess >> including configuration file /etc/freeradius/modules/radutmp >> including configuration file /etc/freeradius/modules/realm >> including configuration file /etc/freeradius/modules/smbpasswd >> including configuration file /etc/freeradius/modules/smsotp >> including configuration file /etc/freeradius/modules/sql_log >> including configuration file >> /etc/freeradius/modules/sqlcounter_expire_on_login >> including configuration file /etc/freeradius/modules/sradutmp >> including configuration file /etc/freeradius/modules/unix >> including configuration file /etc/freeradius/modules/wimax >> including configuration file /etc/freeradius/modules/acct_unique >> including configuration file /etc/freeradius/eap.conf >> including configuration file /etc/freeradius/policy.conf >> including files in directory /etc/freeradius/sites-enabled/ >> including configuration file /etc/freeradius/sites-enabled/default >> including configuration file /etc/freeradius/sites-enabled/inner-tunnel >> main { >> user = "freerad" >> group = "freerad" >> allow_core_dumps = no >> } >> including dictionary file /etc/freeradius/dictionary >> main { >> prefix = "/usr" >> localstatedir = "/var" >> logdir = "/var/log/freeradius" >> libdir = "/usr/lib/freeradius" >> radacctdir = "/var/log/freeradius/radacct" >> hostname_lookups = no >> max_request_time = 30 >> cleanup_delay = 5 >> max_requests = 1024 >> pidfile = "/var/run/freeradius/freeradius.pid" >> checkrad = "/usr/sbin/checkrad" >> debug_level = 0 >> proxy_requests = yes >> log { >> stripped_names = no >> auth = no >> auth_badpass = no >> auth_goodpass = no >> } >> security { >> max_attributes = 200 >> reject_delay = 1 >> status_server = yes >> } >> } >> radiusd: #### Loading Realms and Home Servers #### >> proxy server { >> retry_delay = 5 >> retry_count = 3 >> default_fallback = no >> dead_time = 120 >> wake_all_if_all_dead = no >> } >> home_server localhost { >> ipaddr = 127.0.0.1 >> port = 1812 >> type = "auth" >> secret = "testing123" >> response_window = 20 >> max_outstanding = 65536 >> require_message_authenticator = yes >> zombie_period = 40 >> status_check = "status-server" >> ping_interval = 30 >> check_interval = 30 >> num_answers_to_alive = 3 >> num_pings_to_alive = 3 >> revive_interval = 120 >> status_check_timeout = 4 >> irt = 2 >> mrt = 16 >> mrc = 5 >> mrd = 30 >> } >> home_server_pool my_auth_failover { >> type = fail-over >> home_server = localhost >> } >> realm example.com { >> auth_pool = my_auth_failover >> } >> realm LOCAL { >> } >> radiusd: #### Loading Clients #### >> client localhost { >> ipaddr = 127.0.0.1 >> require_message_authenticator = no >> secret = "testing123" >> nastype = "other" >> } >> radiusd: #### Instantiating modules #### >> instantiate { >> Module: Linked to module rlm_exec >> Module: Instantiating module "exec" from file >> /etc/freeradius/modules/exec >> exec { >> wait = no >> input_pairs = "request" >> shell_escape = yes >> } >> Module: Linked to module rlm_expr >> Module: Instantiating module "expr" from file >> /etc/freeradius/modules/expr >> Module: Linked to module rlm_expiration >> Module: Instantiating module "expiration" from file >> /etc/freeradius/modules/expiration >> expiration { >> reply-message = "Password Has Expired " >> } >> Module: Linked to module rlm_logintime >> Module: Instantiating module "logintime" from file >> /etc/freeradius/modules/logintime >> logintime { >> reply-message = "You are calling outside your allowed timespan " >> minimum-timeout = 60 >> } >> } >> radiusd: #### Loading Virtual Servers #### >> server inner-tunnel { # from file >> /etc/freeradius/sites-enabled/inner-tunnel >> modules { >> Module: Checking authenticate {...} for more modules to load >> Module: Linked to module rlm_pap >> Module: Instantiating module "pap" from file /etc/freeradius/modules/pap >> pap { >> encryption_scheme = "auto" >> auto_header = no >> } >> Module: Linked to module rlm_chap >> Module: Instantiating module "chap" from file >> /etc/freeradius/modules/chap >> Module: Linked to module rlm_mschap >> Module: Instantiating module "mschap" from file >> /etc/freeradius/modules/mschap >> mschap { >> use_mppe = yes >> require_encryption = no >> require_strong = no >> with_ntdomain_hack = no >> } >> Module: Linked to module rlm_unix >> Module: Instantiating module "unix" from file >> /etc/freeradius/modules/unix >> unix { >> radwtmp = "/var/log/freeradius/radwtmp" >> } >> Module: Linked to module rlm_eap >> Module: Instantiating module "eap" from file /etc/freeradius/eap.conf >> eap { >> default_eap_type = "md5" >> timer_expire = 60 >> ignore_unknown_eap_types = no >> cisco_accounting_username_bug = no >> max_sessions = 4096 >> } >> Module: Linked to sub-module rlm_eap_md5 >> Module: Instantiating eap-md5 >> Module: Linked to sub-module rlm_eap_leap >> Module: Instantiating eap-leap >> Module: Linked to sub-module rlm_eap_gtc >> Module: Instantiating eap-gtc >> gtc { >> challenge = "Password: " >> auth_type = "PAP" >> } >> Module: Linked to sub-module rlm_eap_tls >> Module: Instantiating eap-tls >> tls { >> rsa_key_exchange = no >> dh_key_exchange = yes >> rsa_key_length = 512 >> dh_key_length = 512 >> verify_depth = 0 >> CA_path = "/etc/freeradius/certs" >> pem_file_type = yes >> private_key_file = "/etc/freeradius/certs/server.key" >> certificate_file = "/etc/freeradius/certs/server.pem" >> CA_file = "/etc/freeradius/certs/ca.pem" >> private_key_password = "whatever" >> dh_file = "/etc/freeradius/certs/dh" >> random_file = "/dev/urandom" >> fragment_size = 1024 >> include_length = yes >> check_crl = no >> cipher_list = "DEFAULT" >> make_cert_command = "/etc/freeradius/certs/bootstrap" >> cache { >> enable = no >> lifetime = 24 >> max_entries = 255 >> } >> verify { >> } >> } >> Module: Linked to sub-module rlm_eap_ttls >> Module: Instantiating eap-ttls >> ttls { >> default_eap_type = "md5" >> copy_request_to_tunnel = no >> use_tunneled_reply = no >> virtual_server = "inner-tunnel" >> include_length = yes >> } >> Module: Linked to sub-module rlm_eap_peap >> Module: Instantiating eap-peap >> peap { >> default_eap_type = "mschapv2" >> copy_request_to_tunnel = no >> use_tunneled_reply = no >> proxy_tunneled_request_as_eap = yes >> virtual_server = "inner-tunnel" >> } >> Module: Linked to sub-module rlm_eap_mschapv2 >> Module: Instantiating eap-mschapv2 >> mschapv2 { >> with_ntdomain_hack = no >> } >> Module: Checking authorize {...} for more modules to load >> Module: Linked to module rlm_realm >> Module: Instantiating module "suffix" from file >> /etc/freeradius/modules/realm >> realm suffix { >> format = "suffix" >> delimiter = "@" >> ignore_default = no >> ignore_null = no >> } >> Module: Linked to module rlm_files >> Module: Instantiating module "files" from file >> /etc/freeradius/modules/files >> files { >> usersfile = "/etc/freeradius/users" >> acctusersfile = "/etc/freeradius/acct_users" >> preproxy_usersfile = "/etc/freeradius/preproxy_users" >> compat = "no" >> } >> Module: Checking session {...} for more modules to load >> Module: Linked to module rlm_radutmp >> Module: Instantiating module "radutmp" from file >> /etc/freeradius/modules/radutmp >> radutmp { >> filename = "/var/log/freeradius/radutmp" >> username = "%{User-Name}" >> case_sensitive = yes >> check_with_nas = yes >> perm = 384 >> callerid = yes >> } >> Module: Checking post-proxy {...} for more modules to load >> Module: Checking post-auth {...} for more modules to load >> Module: Linked to module rlm_attr_filter >> Module: Instantiating module "attr_filter.access_reject" from file >> /etc/freeradius/modules/attr_filter >> attr_filter attr_filter.access_reject { >> attrsfile = "/etc/freeradius/attrs.access_reject" >> key = "%{User-Name}" >> } >> } # modules >> } # server >> server { # from file /etc/freeradius/radiusd.conf >> modules { >> Module: Checking authenticate {...} for more modules to load >> Module: Linked to module rlm_digest >> Module: Instantiating module "digest" from file >> /etc/freeradius/modules/digest >> Module: Checking authorize {...} for more modules to load >> Module: Linked to module rlm_preprocess >> Module: Instantiating module "preprocess" from file >> /etc/freeradius/modules/preprocess >> preprocess { >> huntgroups = "/etc/freeradius/huntgroups" >> hints = "/etc/freeradius/hints" >> with_ascend_hack = no >> ascend_channels_per_line = 23 >> with_ntdomain_hack = no >> with_specialix_jetstream_hack = no >> with_cisco_vsa_hack = no >> with_alvarion_vsa_hack = no >> } >> Module: Checking preacct {...} for more modules to load >> Module: Linked to module rlm_acct_unique >> Module: Instantiating module "acct_unique" from file >> /etc/freeradius/modules/acct_unique >> acct_unique { >> key = "User-Name, Acct-Session-Id, NAS-IP-Address, >> Client-IP-Address, NAS-Port" >> } >> Module: Checking accounting {...} for more modules to load >> Module: Linked to module rlm_detail >> Module: Instantiating module "detail" from file >> /etc/freeradius/modules/detail >> detail { >> detailfile = >> "/var/log/freeradius/radacct/%{Client-IP-Address}/detail-%Y%m%d" >> header = "%t" >> detailperm = 384 >> dirperm = 493 >> locking = no >> log_packet_header = no >> } >> Module: Instantiating module "attr_filter.accounting_response" from file >> /etc/freeradius/modules/attr_filter >> attr_filter attr_filter.accounting_response { >> attrsfile = "/etc/freeradius/attrs.accounting_response" >> key = "%{User-Name}" >> } >> Module: Checking session {...} for more modules to load >> Module: Checking post-proxy {...} for more modules to load >> Module: Checking post-auth {...} for more modules to load >> } # modules >> } # server >> radiusd: #### Opening IP addresses and Ports #### >> listen { >> type = "auth" >> ipaddr = * >> port = 0 >> } >> listen { >> type = "acct" >> ipaddr = * >> port = 0 >> } >> listen { >> type = "auth" >> ipaddr = 127.0.0.1 >> port = 18120 >> } >> Listening on authentication address * port 1812 >> Listening on accounting address * port 1813 >> Listening on authentication address 127.0.0.1 port 18120 as server >> inner-tunnel >> Listening on proxy address * port 1814 >> Ready to process requests. >> >> >> Thanks for your patience and replies, >> >> Dale >> >> -- >> >> Dale Grice >> >> Staff Engineer, Lab Architect; Motorola >> >> >> >> > > >

3 3

EAP-TLS + Symbian = weird behaviour
by Zeus V Panchenko 14 Oct '11

14 Oct '11

Hi, may somebody advice, please i have: > uname FreeBSD 8.1-RELEASE amd64 > radiusd -v radiusd: FreeRADIUS Version 2.1.10, for host amd64-portbld-freebsd8.1, built on Apr 4 2011 at 22:44:15 radiusd configured with EAP-TLS only and works fine with xNIX-es, WinXP, Android and Maemo with Symbian (Nokia E51, E52) i face much weird picture ... the same device works fine (getting authorized well) via one AP in my LAN and remote VPN, but receiving !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !! EAP session for state ... did not finish! !! Please read http://wiki.freeradius.org/Certificate_Compatibility !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! via another AP (in remote VPN, while other OS still authorized well) AP are the same models and configured the same way what can cause this behaviour? -- Zeus V. Panchenko IT Dpt., IBS ltd GMT+2 (EET)

2 6

terminate session
by OzSpots - Carl Sawers 14 Oct '11

14 Oct '11

Hi All, I am using the latest freeradius and coovachilli and am having a terminate session problem. Some user sessions are not stopping, the session time shown in the DB stops but the user does not logout and there is also no reason given in the DB for termination... The user can also go over the ChilliSpot-Max-Total-Octets quota and the Idle-Timeout does not appear to work. How does radius send a stop session command to the coovachilli router, perhaps that's where the issues is? Regards Carl

3 3