- Freeradius-Users - lists.freeradius.org

Problems with installing to /etc and /var
by jck-freeradius＠southwestern.edu 13 Jul '05

13 Jul '05

I am running freeradius-1.0.4 from source, on SLES 9.0. I want to install freeradius so that it uses /etc and /var, and not /usr/local/etc and /usr/local/var. If I do: /usr/local/src/freeradius-1.0.4 # make clean && make distclean /usr/local/src/freeradius-1.0.4 # ./configure --disable-shared --without-rlm_x99_token --prefix=/ --localstatedir=/var --sysconfdir=/etc --exec-prefix=/ --bindir=/usr/local --sbin=/usr/local --libexec=/usr/local --datadir=/usr/local --libdir=/usr/local --includedir=/usr/local --oldincludedir=/usr/local --infodir=/usr/local --mandir=/usr/local && make Why do I receive this error message: /usr/local/src/freeradius-1.0.4 # src/main/radiusd Fri Jul 8 15:49:43 2005 : Info: Starting - reading configuration files ... radiusd: Couldn't open /usr/local/var/log/radius/radius.log for logging: Permission denied (rlm_exec: Wait=yes but no output defined. Did you mean output=none?) There should be no reference to: Couldn't open /usr/local/var/log/radius/radius.log Full logs of configure and make are viewable at: http://www.southwestern.edu/~johnk/freeradius_build_logs.txt Additionaly, why isn't there a Makefile method for deinstallation? Thanks, --johnk

3 2

mpd vpn + freeradius problem
by 王岩 13 Jul '05

13 Jul '05

Hi, I want to use freeradius1.0.4 to auth and acct mpd_3.18_2 PPTP VPN (on FreeBSD). But I have a problem. In the log file, it displayed the following messages: " Jul 13 10:32:53 vpn mpd: [pptp1] RADIUS: using /usr/local/etc/raddb/radiusd.conf Jul 13 10:32:53 vpn mpd: [pptp1] RADIUS: rad_config: /usr/local/etc/raddb/radiusd.conf:23: invalid timeout Jul 13 10:32:53 vpn mpd: [pptp1] CHAP: sending FAILURE Jul 13 10:32:53 vpn mpd: [pptp1] LCP: authorization failed " I check radiusd.conf:23 . " # The per-request variables are of the form %{Attribute-Name}, and # are taken from the values of the attribute in the incoming # request. See 'doc/variables.txt' for more information. prefix = /usr/local <----------------------line 23 exec_prefix = ${prefix} sysconfdir = ${prefix}/etc localstatedir = ${prefix}/var " Anyone can tell me what it means and how can I resolve it? Thanks wangyan

2 1

Re: eDirectory Issues
by Sayantan Bhowmick 13 Jul '05

13 Jul '05

Hi, Comments inlined. On Tue, 2005-07-12 at 11:15 -0700, jp(a)joshmp.com wrote: > I appologize in advance, but I am new to FreeRADIUS and RADIUS in general. > > Here is my setup: > - Server with FreeRADIUS 1.0.4 --with-edir on FreeBSD 4.11 > - Server with NetWare 6.5.4 > > Here is what I am trying to accomplish: > - Get FreeRADIUS to authenticate VPN users (Cisco VPN Contentrator) to LDAP > database in NetWare tree. > > Here is what I DON'T want to do: > - Mess with eDirectory (profiles, extending the schema, etc.) > > Basically, when this configuration is moved into production, FreeRADIUS would > authenticate users who IDs already exist in a complex, mature NetWare eDir tree. > I don't want to mess with Universal Passwords, extending the schema, etc. I > have already sucessfully configured the Cisco VPN Concentrator to authenticate > users using FreeRADIUS and the UNIX users list. However, I can't get FreeRADIUS > to successfully query the LDAP database on the NetWare server. > > I have been through Novell's documentation, but their docs include building > RADIUS profiles, extending the schema, etc. This is something that I am not > going to be able to do. I have also been up and down the web, FreeRADIUS mail > lists, docs, etc. I have found threads where it is mentioned that you can get > FreeRADIUS to authenticate users to a NetWare LDAP directory using cleartext, > but I have not been able to do this myself. > > I would like to take this in stages: > 1. Succesfully query LDAP without security (with the assumption that this would > be the easiest first step). The debug output shows that FreeRADIUS is already doing this, > 2. Get FreeRADIUS to query LDAP securely. This also can be configured. > > Below you will find the following: > - Text from radiusd.conf file > - Output from radiusd -X > - Text from radius.log file > <- Snipped,.... > # Lightweight Directory Access Protocol (LDAP) > # > # This module definition allows you to use LDAP for > # authorization and authentication (Auth-Type := LDAP) > # > # See doc/rlm_ldap for description of configuration options > # and sample authorize{} and authenticate{} blocks > ldap { > server = "10.1.1.71" > identity = "cn=admin,o=radius" > password = pass > basedn = "o=radius" > filter = "(uid=%{Stripped-User-Name:-%{User-Name}})" > base_filter = "(objectclass=radiusprofile)" > > # set this to 'yes' to use TLS encrypted connections > # to the LDAP database by using the StartTLS extended > # operation. > # The StartTLS operation is supposed to be used with normal > # ldap connections instead of using ldaps (port 689) connections > start_tls = no Set start_tls = yes for making a secure connection to eDirectory. > > # tls_cacertfile = /path/to/cacert.pem Set the path to eDirectory CA cert here. > # tls_cacertdir = /path/to/ca/dir/ > # tls_certfile = /path/to/radius.crt > # tls_keyfile = /path/to/radius.key > # tls_randfile = /path/to/rnd > # tls_require_cert = "demand" > > # default_profile = "cn=radprofile,ou=dialup,o=My Org,c=UA" > # profile_attribute = "radiusProfileDn" > # access_attr = "dialupAccess" > > # Mapping of RADIUS dictionary attributes to LDAP > # directory attributes. > dictionary_mapping = ${raddbdir}/ldap.attrmap > > ldap_connections_number = 5 > > # > # NOTICE: The password_header directive is NOT case insensitive > # > # password_header = "{clear}" > # > # Set: > password_attribute = nspmPassword Set password_attribute to anything other than nspmPassword or comment out this attribute. This will make sure FreeRADIUS does not try to read Universal Password. > # > # to get the user's password from a Novell eDirectory > # backend. This will work *only if* freeRADIUS is > # configured to build with --with-edir option. > # > # > # The server can usually figure this out on its own, and pull > # the correct User-Password or NT-Password from the database. > # > # Note that NT-Passwords MUST be stored as a 32-digit hex > # string, and MUST start off with "0x", such as: > # > # 0x000102030405060708090a0b0c0d0e0f > # > # Without the leading "0x", NT-Passwords will not work. > # This goes for NT-Passwords stored in SQL, too. > # > # password_attribute = userPassword > # > # Un-comment the following to disable Novell eDirectory account > # policy check and intruder detection. This will work *only if* > # FreeRADIUS is configured to build with --with-edir option. > # > edir_account_policy_check=yes > # > # groupname_attribute = cn > # groupmembership_filter = > "(|(&(objectClass=GroupOfNames)(member=%{Ldap-UserDn}))(&(objectClass=GroupOfUniqueNames)(uniquemember=%{Ldap-UserDn})))" > # groupmembership_attribute = radiusGroupName > timeout = 4 > timelimit = 3 > net_timeout = 1 > # compare_check_items = yes > # do_xlat = yes > # access_attr_used_for_allow = yes > } > <-Snipped.... > Ready to process requests. > rad_recv: Access-Request packet from host 127.0.0.1:2302, id=75, length=57 > User-Name = "admin" > User-Password = "pass" > NAS-IP-Address = 255.255.255.255 > NAS-Port = 10 > Processing the authorize section of radiusd.conf > modcall: entering group authorize for request 0 > modcall[authorize]: module "preprocess" returns ok for request 0 > modcall[authorize]: module "chap" returns noop for request 0 > modcall[authorize]: module "mschap" returns noop for request 0 > rlm_realm: No '@' in User-Name = "admin", looking up realm NULL > rlm_realm: No such realm "NULL" > modcall[authorize]: module "suffix" returns noop for request 0 > rlm_eap: No EAP-Message, not doing EAP > modcall[authorize]: module "eap" returns noop for request 0 > users: Matched entry DEFAULT at line 152 > modcall[authorize]: module "files" returns ok for request 0 > rlm_ldap: - authorize > rlm_ldap: performing user authorization for admin > radius_xlat: '(uid=admin)' > radius_xlat: 'o=radius' > rlm_ldap: ldap_get_conn: Checking Id: 0 > rlm_ldap: ldap_get_conn: Got Id: 0 > rlm_ldap: attempting LDAP reconnection > rlm_ldap: (re)connect to 10.1.1.71:389, authentication 0 > rlm_ldap: bind as cn=admin,o=radius/pass to 10.1.1.71:389 > rlm_ldap: waiting for bind result ... > rlm_ldap: Bind was successful > rlm_ldap: performing search in o=radius, with filter (uid=admin) As you can see FreeRADIUS is already querying eDirectory for user information. > rlm_ldap: Error reading Universal Password.Return Code = 80 See comments on password_attribute. > rlm_ldap: looking for check items in directory... > rlm_ldap: looking for reply items in directory... > rlm_ldap: user admin authorized to use remote access > rlm_ldap: ldap_release_conn: Release Id: 0 > modcall[authorize]: module "ldap" returns ok for request 0 > modcall: group authorize returns ok for request 0 > rad_check_password: Found Auth-Type System The Auth-Type is set to System. I reckon this is done by one of the default entries in users file. What is the authentication mechanism you want to use? If you want to use authentication methods like CHAP, MS-CHAP, EAP etc you will have to enable Universal Password. However if you just want to authenticate against eDirectory with plain text password then you need not read Universal Password. You must enable the ldap module in the authenticate section. > auth: type "System" > Processing the authenticate section of radiusd.conf > modcall: entering group authenticate for request 0 > modcall[authenticate]: module "unix" returns notfound for request 0 > modcall: group authenticate returns notfound for request 0 > auth: Failed to validate the user. > Processing the post-auth section of radiusd.conf > modcall: entering group Post-Auth-Type for request 0 > modcall[post-auth]: module "ldap" returns noop for request 0 > modcall: group Post-Auth-Type returns noop for request 0 > Delaying request 0 for 1 seconds > Finished request 0 > Going to the next request > --- Walking the entire request list --- > Waking up in 1 seconds... > --- Walking the entire request list --- > Waking up in 1 seconds... > --- Walking the entire request list --- > Sending Access-Reject of id 75 to 127.0.0.1:2302 > Waking up in 4 seconds... > --- Walking the entire request list --- > Cleaning up request 0 ID 75 with timestamp 42d39d5d > Nothing to do. Sleeping until we see a request. > -----END RADIUSD DEBUG----- > > The line that I find disturbing is the "error reading Universal Password" line. > I assume that I must edit my config in some way so that FreeRADIUS is not > attempting to read a Universal Password, or somehow tells NLDAP not to send a > Universal Password. Hope this helps. Get back to me in case you have any further queries. -Sayantan.

1 0

OpenCA Certificates Problem with EAP_TLS
by Pablo Navas 13 Jul '05

13 Jul '05

Hello list, I’m sending this e-mail to ask about a problem with certificates generated by OpenCA and used with FreeRadius. My problem is similar to the one that Tom Tim had using EAP_TLS and the same type of CA. From what I’ve read, the solution was to export the certificates as pcks12 and then convert them to pem with openssl. At first, I made the EAP_TLS work using the test certificates. I had no problem doing this. However, when I used mine, things did not go so well ?. I have tried using the Radius Server Certificate, using two different types: TLS WEB SERVER and VPN SERVER. Also, I have tried using that of the client, such as TLS WEB CLIENT. I have converted them using 2 different methods: 1. openssl pkcs12 -in cert.p12 -out cert.pem (This seems to be similar to cert-srv.pem) 2. openssl pkcs12 -clcerts -nokeys -in cert.p12 -out usercert.pem openssl pkcs12 -nocerts -in cert.p12 -out userkey.pem (These are similar to the one above, except that they are separated.) To confirm this, I looked at the certificates with openssl x509 -in cert.pem –text, and it appears that everything is correct. I have attached the log given by the FreeRadius. The server never sends the Accept-Access, but it doesn’t give many clues as to what is happening either, except: TLS_accept:error in SSLv3 read client certificate A. I hope that someone is able to help me out with this, I am a bit frustrated with it and I need to get it up and running. Best regards. Starting - reading configuration files ... reread_config: reading radiusd.conf Config: including file: /etc/raddb/proxy.conf Config: including file: /etc/raddb/clients.conf Config: including file: /etc/raddb/snmp.conf Config: including file: /etc/raddb/eap.conf Config: including file: /etc/raddb/sql.conf main: prefix = "/usr/local" main: localstatedir = "/usr/local/var" main: logdir = "/usr/local/var/log/radius" main: libdir = "/usr/local/lib" main: radacctdir = "/usr/local/var/log/radius/radacct" main: hostname_lookups = no main: max_request_time = 30 main: cleanup_delay = 5 main: max_requests = 1024 main: delete_blocked_requests = 0 main: port = 0 main: allow_core_dumps = no main: log_stripped_names = yes main: log_file = "/usr/local/var/log/radius/radius.log" main: log_auth = yes main: log_auth_badpass = yes main: log_auth_goodpass = no main: pidfile = "/usr/local/var/run/radiusd/radiusd.pid" main: user = "(null)" main: group = "(null)" main: usercollide = no main: lower_user = "no" main: lower_pass = "no" main: nospace_user = "no" main: nospace_pass = "no" main: checkrad = "/usr/local/sbin/checkrad" main: proxy_requests = yes proxy: retry_delay = 5 proxy: retry_count = 3 proxy: synchronous = no proxy: default_fallback = yes proxy: dead_time = 120 proxy: post_proxy_authorize = yes proxy: wake_all_if_all_dead = no security: max_attributes = 200 security: reject_delay = 1 security: status_server = no main: debug_level = 0 read_config_files: reading dictionary read_config_files: reading naslist Using deprecated naslist file. Support for this will go away soon. read_config_files: reading clients read_config_files: reading realms radiusd: entering modules setup Module: Library search path is /usr/local/lib Module: Loaded exec exec: wait = yes exec: program = "(null)" exec: input_pairs = "request" exec: output_pairs = "(null)" exec: packet_type = "(null)" rlm_exec: Wait=yes but no output defined. Did you mean output=none? Module: Instantiated exec (exec) Module: Loaded expr Module: Instantiated expr (expr) Module: Loaded LDAP ldap: server = "localhost" ldap: port = 389 ldap: net_timeout = 1 ldap: timeout = 4 ldap: timelimit = 3 ldap: identity = "cn=admin,o=uah,c=es" ldap: tls_mode = no ldap: start_tls = no ldap: tls_cacertfile = "(null)" ldap: tls_cacertdir = "(null)" ldap: tls_certfile = "(null)" ldap: tls_keyfile = "(null)" ldap: tls_randfile = "(null)" ldap: tls_require_cert = "allow" ldap: password = "clave" ldap: basedn = "ou=radius,o=uah,c=es" ldap: filter = "(cn=%u)" ldap: base_filter = "(objectclass=radiusprofile)" ldap: default_profile = "(null)" ldap: profile_attribute = "(null)" ldap: password_header = "{clear}" ldap: password_attribute = "(null)" ldap: access_attr = "(null)" ldap: groupname_attribute = "cn" ldap: groupmembership_filter = "(|(&(objectClass=GroupOfNames)(member=%{Ldap-UserDn}))(&(objectClass=GroupOfUniqueNames)(uniquemember=%{Ldap-UserDn})))" ldap: groupmembership_attribute = "(null)" ldap: dictionary_mapping = "/etc/raddb/ldap.attrmap" ldap: ldap_debug = 0 ldap: ldap_connections_number = 5 ldap: compare_check_items = no ldap: access_attr_used_for_allow = yes ldap: do_xlat = yes rlm_ldap: Registering ldap_groupcmp for Ldap-Group rlm_ldap: Registering ldap_xlat with xlat_name ldap rlm_ldap: reading ldap<->radius mappings from file /etc/raddb/ldap.attrmap rlm_ldap: LDAP radiusCheckItem mapped to RADIUS $GENERIC$ rlm_ldap: LDAP radiusReplyItem mapped to RADIUS $GENERIC$ rlm_ldap: LDAP userPassword mapped to RADIUS User-Password rlm_ldap: LDAP radiusAuthType mapped to RADIUS Auth-Type rlm_ldap: LDAP radiusSimultaneousUse mapped to RADIUS Simultaneous-Use rlm_ldap: LDAP radiusCalledStationId mapped to RADIUS Called-Station-Id rlm_ldap: LDAP radiusCallingStationId mapped to RADIUS Calling-Station-Id rlm_ldap: LDAP lmPassword mapped to RADIUS LM-Password rlm_ldap: LDAP ntPassword mapped to RADIUS NT-Password rlm_ldap: LDAP acctFlags mapped to RADIUS SMB-Account-CTRL-TEXT rlm_ldap: LDAP radiusExpiration mapped to RADIUS Expiration rlm_ldap: LDAP radiusServiceType mapped to RADIUS Service-Type rlm_ldap: LDAP radiusFramedProtocol mapped to RADIUS Framed-Protocol rlm_ldap: LDAP radiusFramedIPAddress mapped to RADIUS Framed-IP-Address rlm_ldap: LDAP radiusFramedIPNetmask mapped to RADIUS Framed-IP-Netmask rlm_ldap: LDAP radiusFramedRoute mapped to RADIUS Framed-Route rlm_ldap: LDAP radiusFramedRouting mapped to RADIUS Framed-Routing rlm_ldap: LDAP radiusFilterId mapped to RADIUS Filter-Id rlm_ldap: LDAP radiusFramedMTU mapped to RADIUS Framed-MTU rlm_ldap: LDAP radiusFramedCompression mapped to RADIUS Framed-Compression rlm_ldap: LDAP radiusLoginIPHost mapped to RADIUS Login-IP-Host rlm_ldap: LDAP radiusLoginService mapped to RADIUS Login-Service rlm_ldap: LDAP radiusLoginTCPPort mapped to RADIUS Login-TCP-Port rlm_ldap: LDAP radiusCallbackNumber mapped to RADIUS Callback-Number rlm_ldap: LDAP radiusCallbackId mapped to RADIUS Callback-Id rlm_ldap: LDAP radiusFramedIPXNetwork mapped to RADIUS Framed-IPX-Network rlm_ldap: LDAP radiusClass mapped to RADIUS Class rlm_ldap: LDAP radiusSessionTimeout mapped to RADIUS Session-Timeout rlm_ldap: LDAP radiusIdleTimeout mapped to RADIUS Idle-Timeout rlm_ldap: LDAP radiusTerminationAction mapped to RADIUS Termination-Action rlm_ldap: LDAP radiusLoginLATService mapped to RADIUS Login-LAT-Service rlm_ldap: LDAP radiusLoginLATNode mapped to RADIUS Login-LAT-Node rlm_ldap: LDAP radiusLoginLATGroup mapped to RADIUS Login-LAT-Group rlm_ldap: LDAP radiusFramedAppleTalkLink mapped to RADIUS Framed-AppleTalk-Link rlm_ldap: LDAP radiusFramedAppleTalkNetwork mapped to RADIUS Framed-AppleTalk-Network rlm_ldap: LDAP radiusFramedAppleTalkZone mapped to RADIUS Framed-AppleTalk-Zone rlm_ldap: LDAP radiusPortLimit mapped to RADIUS Port-Limit rlm_ldap: LDAP radiusLoginLATPort mapped to RADIUS Login-LAT-Port conns: 0x8113370 Module: Instantiated ldap (ldap) Module: Loaded eap eap: default_eap_type = "tls" eap: timer_expire = 60 eap: ignore_unknown_eap_types = yes eap: cisco_accounting_username_bug = no rlm_eap: Loaded and initialized type md5 rlm_eap: Loaded and initialized type leap gtc: challenge = "Password: " gtc: auth_type = "PAP" rlm_eap: Loaded and initialized type gtc tls: rsa_key_exchange = no tls: dh_key_exchange = yes tls: rsa_key_length = 512 tls: dh_key_length = 512 tls: verify_depth = 0 tls: CA_path = "/etc/raddb/certs/" tls: pem_file_type = yes tls: private_key_file = "/etc/raddb/certs/vpn.crusa.com.pem" tls: certificate_file = "/etc/raddb/certs/vpn.crusa.com.pem" tls: CA_file = "/etc/raddb/certs/ca.pem" tls: private_key_password = "claveclave" tls: dh_file = "/etc/raddb/certs/dh" tls: random_file = "/etc/raddb/certs/random" tls: fragment_size = 1024 tls: include_length = yes tls: check_crl = no tls: check_cert_cn = "(null)" rlm_eap: Loaded and initialized type tls ttls: default_eap_type = "md5" ttls: copy_request_to_tunnel = no ttls: use_tunneled_reply = no rlm_eap: Loaded and initialized type ttls peap: default_eap_type = "mschapv2" peap: copy_request_to_tunnel = no peap: use_tunneled_reply = no peap: proxy_tunneled_request_as_eap = yes rlm_eap: Loaded and initialized type peap mschapv2: with_ntdomain_hack = no rlm_eap: Loaded and initialized type mschapv2 Module: Instantiated eap (eap) Module: Loaded preprocess preprocess: huntgroups = "/etc/raddb/huntgroups" preprocess: hints = "/etc/raddb/hints" preprocess: with_ascend_hack = no preprocess: ascend_channels_per_line = 23 preprocess: with_ntdomain_hack = no preprocess: with_specialix_jetstream_hack = no preprocess: with_cisco_vsa_hack = no Module: Instantiated preprocess (preprocess) Module: Loaded CHAP Module: Instantiated chap (chap) Module: Loaded MS-CHAP mschap: use_mppe = yes mschap: require_encryption = no mschap: require_strong = no mschap: with_ntdomain_hack = no mschap: passwd = "(null)" mschap: authtype = "MS-CHAP" mschap: ntlm_auth = "(null)" Module: Instantiated mschap (mschap) Module: Loaded realm realm: format = "suffix" realm: delimiter = "@" realm: ignore_default = no realm: ignore_null = no Module: Instantiated realm (suffix) Module: Loaded files files: usersfile = "/etc/raddb/users" files: acctusersfile = "/etc/raddb/acct_users" files: preproxy_usersfile = "/etc/raddb/preproxy_users" files: compat = "no" Module: Instantiated files (files) Module: Loaded SQL sql: driver = "rlm_sql_mysql" sql: server = "localhost" sql: port = "" sql: login = "radius_user" sql: password = "radiuspass" sql: radius_db = "radius" sql: acct_table = "radacct" sql: acct_table2 = "radacct" sql: authcheck_table = "radcheck" sql: authreply_table = "radreply" sql: groupcheck_table = "radgroupcheck" sql: groupreply_table = "radgroupreply" sql: usergroup_table = "usergroup" sql: nas_table = "nas" sql: dict_table = "dictionary" sql: sqltrace = no sql: sqltracefile = "/usr/local/var/log/radius/sqltrace.sql" sql: readclients = no sql: deletestalesessions = yes sql: num_sql_socks = 5 sql: sql_user_name = "%{User-Name}" sql: default_user_profile = "" sql: query_on_not_found = no sql: authorize_check_query = "SELECT id,UserName,Attribute,Value,op FROM radcheck WHERE Username = '%{SQL-User-Name}' ORDER BY id" sql: authorize_reply_query = "SELECT id,UserName,Attribute,Value,op FROM radreply WHERE Username = '%{SQL-User-Name}' ORDER BY id" sql: authorize_group_check_query = "SELECT radgroupcheck.id,radgroupcheck.GroupName,radgroupcheck.Attribute,radgroupcheck.Value,radgroupcheck.op FROM radgroupcheck,usergroup WHERE usergroup.Username = '%{SQL-User-Name}' AND usergroup.GroupName = radgroupcheck.GroupName ORDER BY radgroupcheck.id" sql: authorize_group_reply_query = "SELECT radgroupreply.id,radgroupreply.GroupName,radgroupreply.Attribute,radgroupreply.Value,radgroupreply.op FROM radgroupreply,usergroup WHERE usergroup.Username = '%{SQL-User-Name}' AND usergroup.GroupName = radgroupreply.GroupName ORDER BY radgroupreply.id" sql: accounting_onoff_query = "UPDATE radacct SET AcctStopTime='%S', AcctSessionTime=unix_timestamp('%S') - unix_timestamp(AcctStartTime), AcctTerminateCause='%{Acct-Terminate-Cause}', AcctStopDelay = '%{Acct-Delay-Time}' WHERE AcctSessionTime=0 AND AcctStopTime=0 AND NASIPAddress= '%{NAS-IP-Address}' AND AcctStartTime <= '%S'" sql: accounting_update_query = "UPDATE radacct ? SET FramedIPAddress = '%{Framed-IP-Address}', ? AcctSessionTime = '%{Acct-Session-Time}', ? AcctInputOctets = '%{Acct-Input-Octets}', ? AcctOutputOctets = '%{Acct-Output-Octets}' ? WHERE AcctSessionId = '%{Acct-Session-Id}' ? AND UserName = '%{SQL-User-Name}' ? AND NASIPAddress= '%{NAS-IP-Address}'" sql: accounting_update_query_alt = "INSERT into radacct (AcctSessionId, AcctUniqueId, UserName, Realm, NASIPAddress, NASPortId, NASPortType, AcctStartTime, AcctSessionTime, AcctAuthentic, ConnectInfo_start, AcctInputOctets, AcctOutputOctets, CalledStationId, CallingStationId, ServiceType, FramedProtocol, FramedIPAddress, AcctStartDelay) values('%{Acct-Session-Id}', '%{Acct-Unique-Session-Id}', '%{SQL-User-Name}', '%{Realm}', '%{NAS-IP-Address}', '%{NAS-Port}', '%{NAS-Port-Type}', DATE_SUB('%S',INTERVAL (%{Acct-Session-Time:-0} + %{Acct-Delay-Time:-0}) SECOND), '%{Acct-Session-Time}', '%{Acct-Authentic}', '', '%{Acct-Input-Octets}', '%{Acct-Output-Octets}', '%{Called-Station-Id}', '%{Calling-Station-Id}', '%{Service-Type}', '%{Framed-Protocol}', '%{Framed-IP-Address}', '0')" sql: accounting_start_query = "INSERT into radacct (AcctSessionId, AcctUniqueId, UserName, Realm, NASIPAddress, NASPortId, NASPortType, AcctStartTime, AcctStopTime, AcctSessionTime, AcctAuthentic, ConnectInfo_start, ConnectInfo_stop, AcctInputOctets, AcctOutputOctets, CalledStationId, CallingStationId, AcctTerminateCause, ServiceType, FramedProtocol, FramedIPAddress, AcctStartDelay, AcctStopDelay) values('%{Acct-Session-Id}', '%{Acct-Unique-Session-Id}', '%{SQL-User-Name}', '%{Realm}', '%{NAS-IP-Address}', '%{NAS-Port}', '%{NAS-Port-Type}', '%S', '0', '0', '%{Acct-Authentic}', '%{Connect-Info}', '', '0', '0', '%{Called-Station-Id}', '%{Calling-Station-Id}', '', '%{Service-Type}', '%{Framed-Protocol}', '%{Framed-IP-Address}', '%{Acct-Delay-Time}', '0')" sql: accounting_start_query_alt = "UPDATE radacct SET AcctStartTime = '%S', AcctStartDelay = '%{Acct-Delay-Time}', ConnectInfo_start = '%{Connect-Info}' WHERE AcctSessionId = '%{Acct-Session-Id}' AND UserName = '%{SQL-User-Name}' AND NASIPAddress = '%{NAS-IP-Address}'" sql: accounting_stop_query = "UPDATE radacct SET AcctStopTime = '%S', AcctSessionTime = '%{Acct-Session-Time}', AcctInputOctets = '%{Acct-Input-Octets}', AcctOutputOctets = '%{Acct-Output-Octets}', AcctTerminateCause = '%{Acct-Terminate-Cause}', AcctStopDelay = '%{Acct-Delay-Time}', ConnectInfo_stop = '%{Connect-Info}' WHERE AcctSessionId = '%{Acct-Session-Id}' AND UserName = '%{SQL-User-Name}' AND NASIPAddress = '%{NAS-IP-Address}'" sql: accounting_stop_query_alt = "INSERT into radacct (AcctSessionId, AcctUniqueId, UserName, Realm, NASIPAddress, NASPortId, NASPortType, AcctStartTime, AcctStopTime, AcctSessionTime, AcctAuthentic, ConnectInfo_start, ConnectInfo_stop, AcctInputOctets, AcctOutputOctets, CalledStationId, CallingStationId, AcctTerminateCause, ServiceType, FramedProtocol, FramedIPAddress, AcctStartDelay, AcctStopDelay) values('%{Acct-Session-Id}', '%{Acct-Unique-Session-Id}', '%{SQL-User-Name}', '%{Realm}', '%{NAS-IP-Address}', '%{NAS-Port}', '%{NAS-Port-Type}', DATE_SUB('%S', INTERVAL (%{Acct-Session-Time:-0} + %{Acct-Delay-Time:-0}) SECOND), '%S', '%{Acct-Session-Time}', '%{Acct-Authentic}', '', '%{Connect-Info}', '%{Acct-Input-Octets}', '%{Acct-Output-Octets}', '%{Called-Station-Id}', '%{Calling-Station-Id}', '%{Acct-Terminate-Cause}', '%{Service-Type}', '%{Framed-Protocol}', '%{Framed-IP-Address}', '0', '%{Acct-Delay-Time}')" sql: group_membership_query = "SELECT GroupName FROM usergroup WHERE UserName='%{SQL-User-Name}'" sql: connect_failure_retry_delay = 60 sql: simul_count_query = "" sql: simul_verify_query = "SELECT RadAcctId, AcctSessionId, UserName, NASIPAddress, NASPortId, FramedIPAddress, CallingStationId, FramedProtocol FROM radacct WHERE UserName='%{SQL-User-Name}' AND AcctStopTime = 0" sql: postauth_table = "radpostauth" sql: postauth_query = "INSERT into radpostauth (id, user, pass, reply, date) values ('', '%{User-Name}', '%{User-Password:-Chap-Password}', '%{reply:Packet-Type}', NOW())" sql: safe-characters = "@abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789.-_: /" rlm_sql (sql): Driver rlm_sql_mysql (module rlm_sql_mysql) loaded and linked rlm_sql (sql): Attempting to connect to radius_user@localhost:/radius rlm_sql (sql): starting 0 rlm_sql (sql): Attempting to connect rlm_sql_mysql #0 rlm_sql_mysql: Starting connect to MySQL server for #0 rlm_sql (sql): Connected new DB handle, #0 rlm_sql (sql): starting 1 rlm_sql (sql): Attempting to connect rlm_sql_mysql #1 rlm_sql_mysql: Starting connect to MySQL server for #1 rlm_sql (sql): Connected new DB handle, #1 rlm_sql (sql): starting 2 rlm_sql (sql): Attempting to connect rlm_sql_mysql #2 rlm_sql_mysql: Starting connect to MySQL server for #2 rlm_sql (sql): Connected new DB handle, #2 rlm_sql (sql): starting 3 rlm_sql (sql): Attempting to connect rlm_sql_mysql #3 rlm_sql_mysql: Starting connect to MySQL server for #3 rlm_sql (sql): Connected new DB handle, #3 rlm_sql (sql): starting 4 rlm_sql (sql): Attempting to connect rlm_sql_mysql #4 rlm_sql_mysql: Starting connect to MySQL server for #4 rlm_sql (sql): Connected new DB handle, #4 Module: Instantiated sql (sql) Module: Loaded Acct-Unique-Session-Id acct_unique: key = "User-Name, Acct-Session-Id, NAS-IP-Address, Client-IP-Address, NAS-Port" Module: Instantiated acct_unique (acct_unique) Module: Loaded detail detail: detailfile = "/usr/local/var/log/radius/radacct/%{Client-IP-Address}/detail-%Y%m%d" detail: detailperm = 384 detail: dirperm = 493 detail: locking = no Module: Instantiated detail (detail) Module: Loaded radutmp radutmp: filename = "/usr/local/var/log/radius/radutmp" radutmp: username = "%{User-Name}" radutmp: case_sensitive = yes radutmp: check_with_nas = yes radutmp: perm = 384 radutmp: callerid = yes Module: Instantiated radutmp (radutmp) Listening on authentication *:1812 Listening on accounting *:1813 Listening on proxy *:1814 Ready to process requests. rad_recv: Access-Request packet from host 10.0.0.11:1812, id=138, length=84 User-Name = "mobile" NAS-IP-Address = 10.0.0.11 Calling-Station-Id = "00-0E-35-5D-B5-25" EAP-Message = 0x023e000b016d6f62696c65 Message-Authenticator = 0x362fa760e942a62b4137dd87c2050deb Processing the authorize section of radiusd.conf modcall: entering group authorize for request 0 modcall[authorize]: module "preprocess" returns ok for request 0 modcall[authorize]: module "chap" returns noop for request 0 modcall[authorize]: module "mschap" returns noop for request 0 rlm_realm: No '@' in User-Name = "mobile", looking up realm NULL rlm_realm: No such realm "NULL" modcall[authorize]: module "suffix" returns noop for request 0 users: Matched entry DEFAULT at line 185 users: Matched entry mobile at line 227 modcall[authorize]: module "files" returns ok for request 0 rlm_eap: EAP packet type response id 62 length 11 rlm_eap: No EAP Start, assuming it's an on-going EAP conversation modcall[authorize]: module "eap" returns updated for request 0 radius_xlat: 'mobile' rlm_sql (sql): sql_set_user escaped user --> 'mobile' radius_xlat: 'SELECT id,UserName,Attribute,Value,op FROM radcheck WHERE Username = 'mobile' ORDER BY id' rlm_sql (sql): Reserving sql socket id: 4 rlm_sql (sql): User mobile not found in radcheck radius_xlat: 'SELECT radgroupcheck.id,radgroupcheck.GroupName,radgroupcheck.Attribute,radgroupcheck.Value,radgroupcheck.op FROM radgroupcheck,usergroup WHERE usergroup.Username = 'mobile' AND usergroup.GroupName = radgroupcheck.GroupName ORDER BY radgroupcheck.id' radius_xlat: 'SELECT radgroupreply.id,radgroupreply.GroupName,radgroupreply.Attribute,radgroupreply.Value,radgroupreply.op FROM radgroupreply,usergroup WHERE usergroup.Username = 'mobile' AND usergroup.GroupName = radgroupreply.GroupName ORDER BY radgroupreply.id' rlm_sql (sql): Released sql socket id: 4 modcall[authorize]: module "sql" returns ok for request 0 rlm_ldap: - authorize rlm_ldap: performing user authorization for mobile radius_xlat: '(cn=mobile)' radius_xlat: 'ou=radius,o=uah,c=es' rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: attempting LDAP reconnection rlm_ldap: (re)connect to localhost:389, authentication 0 rlm_ldap: bind as cn=admin,o=uah,c=es/clave to localhost:389 rlm_ldap: waiting for bind result ... rlm_ldap: Bind was successful rlm_ldap: performing search in ou=radius,o=uah,c=es, with filter (cn=mobile) rlm_ldap: object not found or got ambiguous search result rlm_ldap: search failed rlm_ldap: ldap_release_conn: Release Id: 0 modcall[authorize]: module "ldap" returns notfound for request 0 modcall: group authorize returns updated for request 0 rad_check_password: Found Auth-Type EAP rad_check_password: Found Auth-Type EAP Warning: Found 2 auth-types on request for user 'mobile' auth: type "EAP" Processing the authenticate section of radiusd.conf modcall: entering group authenticate for request 0 rlm_eap: EAP Identity rlm_eap: processing type tls rlm_eap_tls: Requiring client certificate rlm_eap_tls: Initiate rlm_eap_tls: Start returned 1 modcall[authenticate]: module "eap" returns handled for request 0 modcall: group authenticate returns handled for request 0 Sending Access-Challenge of id 138 to 10.0.0.11:1812 EAP-Message = 0x013f00060d20 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x468de1ca8a58a4399a5f6a4d5b4e06fd Finished request 0 Going to the next request --- Walking the entire request list --- Waking up in 6 seconds... rad_recv: Access-Request packet from host 10.0.0.11:1812, id=139, length=197 User-Name = "mobile" NAS-IP-Address = 10.0.0.11 Calling-Station-Id = "00-0E-35-5D-B5-25" State = 0x468de1ca8a58a4399a5f6a4d5b4e06fd EAP-Message = 0x023f006a0d8000000060160301005b01000057030142ca471887c23c7bfa361947c335437e2f9064b45923ead412ecbdbdf714facc00003000390038003500160013000a00330032002f0066000500040065006400630062006000150012000900140011000800030100 Message-Authenticator = 0xb84784150e58662d6a5ba31ee84b2c38 Processing the authorize section of radiusd.conf modcall: entering group authorize for request 1 modcall[authorize]: module "preprocess" returns ok for request 1 modcall[authorize]: module "chap" returns noop for request 1 modcall[authorize]: module "mschap" returns noop for request 1 rlm_realm: No '@' in User-Name = "mobile", looking up realm NULL rlm_realm: No such realm "NULL" modcall[authorize]: module "suffix" returns noop for request 1 users: Matched entry DEFAULT at line 185 users: Matched entry mobile at line 227 modcall[authorize]: module "files" returns ok for request 1 rlm_eap: EAP packet type response id 63 length 106 rlm_eap: No EAP Start, assuming it's an on-going EAP conversation modcall[authorize]: module "eap" returns updated for request 1 radius_xlat: 'mobile' rlm_sql (sql): sql_set_user escaped user --> 'mobile' radius_xlat: 'SELECT id,UserName,Attribute,Value,op FROM radcheck WHERE Username = 'mobile' ORDER BY id' rlm_sql (sql): Reserving sql socket id: 3 rlm_sql (sql): User mobile not found in radcheck radius_xlat: 'SELECT radgroupcheck.id,radgroupcheck.GroupName,radgroupcheck.Attribute,radgroupcheck.Value,radgroupcheck.op FROM radgroupcheck,usergroup WHERE usergroup.Username = 'mobile' AND usergroup.GroupName = radgroupcheck.GroupName ORDER BY radgroupcheck.id' radius_xlat: 'SELECT radgroupreply.id,radgroupreply.GroupName,radgroupreply.Attribute,radgroupreply.Value,radgroupreply.op FROM radgroupreply,usergroup WHERE usergroup.Username = 'mobile' AND usergroup.GroupName = radgroupreply.GroupName ORDER BY radgroupreply.id' rlm_sql (sql): Released sql socket id: 3 modcall[authorize]: module "sql" returns ok for request 1 rlm_ldap: - authorize rlm_ldap: performing user authorization for mobile radius_xlat: '(cn=mobile)' radius_xlat: 'ou=radius,o=uah,c=es' rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=radius,o=uah,c=es, with filter (cn=mobile) rlm_ldap: object not found or got ambiguous search result rlm_ldap: search failed rlm_ldap: ldap_release_conn: Release Id: 0 modcall[authorize]: module "ldap" returns notfound for request 1 modcall: group authorize returns updated for request 1 rad_check_password: Found Auth-Type EAP rad_check_password: Found Auth-Type EAP Warning: Found 2 auth-types on request for user 'mobile' auth: type "EAP" Processing the authenticate section of radiusd.conf modcall: entering group authenticate for request 1 rlm_eap: Request found, released from the list rlm_eap: EAP/tls rlm_eap: processing type tls rlm_eap_tls: Authenticate rlm_eap_tls: processing TLS rlm_eap_tls: Length Included eaptls_verify returned 11 (other): before/accept initialization TLS_accept: before/accept initialization rlm_eap_tls: <<< TLS 1.0 Handshake [length 005b], ClientHello TLS_accept: SSLv3 read client hello A rlm_eap_tls: >>> TLS 1.0 Handshake [length 004a], ServerHello TLS_accept: SSLv3 write server hello A rlm_eap_tls: >>> TLS 1.0 Handshake [length 0f5d], Certificate TLS_accept: SSLv3 write certificate A rlm_eap_tls: >>> TLS 1.0 Handshake [length 028d], ServerKeyExchange TLS_accept: SSLv3 write key exchange A rlm_eap_tls: >>> TLS 1.0 Handshake [length 008b], CertificateRequest TLS_accept: SSLv3 write certificate request A TLS_accept: SSLv3 flush data TLS_accept:error in SSLv3 read client certificate A In SSL Handshake Phase In SSL Accept mode eaptls_process returned 13 modcall[authenticate]: module "eap" returns handled for request 1 modcall: group authenticate returns handled for request 1 Sending Access-Challenge of id 139 to 10.0.0.11:1812 EAP-Message = 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 EAP-Message = 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 EAP-Message = 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 EAP-Message = 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 EAP-Message = 0x7474703a2f2f796f64612e6175742e7561682e65732f Message-Authenticator = 0x00000000000000000000000000000000 State = 0x87945d41551fdf29b9808e0bf93b1364 Finished request 1 Going to the next request Waking up in 6 seconds... rad_recv: Access-Request packet from host 10.0.0.11:1812, id=140, length=97 User-Name = "mobile" NAS-IP-Address = 10.0.0.11 Calling-Station-Id = "00-0E-35-5D-B5-25" State = 0x87945d41551fdf29b9808e0bf93b1364 EAP-Message = 0x024000060d00 Message-Authenticator = 0x12b77eb84f2a1926f8492d0219f6a117 Processing the authorize section of radiusd.conf modcall: entering group authorize for request 2 modcall[authorize]: module "preprocess" returns ok for request 2 modcall[authorize]: module "chap" returns noop for request 2 modcall[authorize]: module "mschap" returns noop for request 2 rlm_realm: No '@' in User-Name = "mobile", looking up realm NULL rlm_realm: No such realm "NULL" modcall[authorize]: module "suffix" returns noop for request 2 users: Matched entry DEFAULT at line 185 users: Matched entry mobile at line 227 modcall[authorize]: module "files" returns ok for request 2 rlm_eap: EAP packet type response id 64 length 6 rlm_eap: No EAP Start, assuming it's an on-going EAP conversation modcall[authorize]: module "eap" returns updated for request 2 radius_xlat: 'mobile' rlm_sql (sql): sql_set_user escaped user --> 'mobile' radius_xlat: 'SELECT id,UserName,Attribute,Value,op FROM radcheck WHERE Username = 'mobile' ORDER BY id' rlm_sql (sql): Reserving sql socket id: 2 rlm_sql (sql): User mobile not found in radcheck radius_xlat: 'SELECT radgroupcheck.id,radgroupcheck.GroupName,radgroupcheck.Attribute,radgroupcheck.Value,radgroupcheck.op FROM radgroupcheck,usergroup WHERE usergroup.Username = 'mobile' AND usergroup.GroupName = radgroupcheck.GroupName ORDER BY radgroupcheck.id' radius_xlat: 'SELECT radgroupreply.id,radgroupreply.GroupName,radgroupreply.Attribute,radgroupreply.Value,radgroupreply.op FROM radgroupreply,usergroup WHERE usergroup.Username = 'mobile' AND usergroup.GroupName = radgroupreply.GroupName ORDER BY radgroupreply.id' rlm_sql (sql): Released sql socket id: 2 modcall[authorize]: module "sql" returns ok for request 2 rlm_ldap: - authorize rlm_ldap: performing user authorization for mobile radius_xlat: '(cn=mobile)' radius_xlat: 'ou=radius,o=uah,c=es' rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=radius,o=uah,c=es, with filter (cn=mobile) rlm_ldap: object not found or got ambiguous search result rlm_ldap: search failed rlm_ldap: ldap_release_conn: Release Id: 0 modcall[authorize]: module "ldap" returns notfound for request 2 modcall: group authorize returns updated for request 2 rad_check_password: Found Auth-Type EAP rad_check_password: Found Auth-Type EAP Warning: Found 2 auth-types on request for user 'mobile' auth: type "EAP" Processing the authenticate section of radiusd.conf modcall: entering group authenticate for request 2 rlm_eap: Request found, released from the list rlm_eap: EAP/tls rlm_eap: processing type tls rlm_eap_tls: Authenticate rlm_eap_tls: processing TLS rlm_eap_tls: Received EAP-TLS ACK message rlm_eap_tls: ack handshake fragment handler eaptls_verify returned 1 eaptls_process returned 13 modcall[authenticate]: module "eap" returns handled for request 2 modcall: group authenticate returns handled for request 2 Sending Access-Challenge of id 140 to 10.0.0.11:1812 EAP-Message = 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 EAP-Message = 0x010901160e706b69406175742e7561682e6573820900ae7948d122becdf5301e0603551d1104173015811376706e2d61646d696e4063727573612e636f6d30190603551d1204123010810e706b69406175742e7561682e6573303906096086480186f8420104042c162a687474703a2f2f6f626977616e2e6175742e7561682e65732f7075622f63726c2f636163726c2e63726c303906096086480186f8420103042c162a687474703a2f2f6f626977616e2e6175742e7561682e65732f7075622f63726c2f636163726c2e63726c303b0603551d1f043430323030a02ea02c862a687474703a2f2f6f626977616e2e6175742e7561682e65732f7075 EAP-Message = 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 EAP-Message = 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 EAP-Message = 0x80725ad754035e7b3fcac22ee583c19032270f922f2e Message-Authenticator = 0x00000000000000000000000000000000 State = 0x8de1f909e4a87c97855957e5253bae2c Finished request 2 Going to the next request Waking up in 6 seconds... rad_recv: Access-Request packet from host 10.0.0.11:1812, id=141, length=97 User-Name = "mobile" NAS-IP-Address = 10.0.0.11 Calling-Station-Id = "00-0E-35-5D-B5-25" State = 0x8de1f909e4a87c97855957e5253bae2c EAP-Message = 0x024100060d00 Message-Authenticator = 0x840fbc4d13b0a07288c5d1659371118d Processing the authorize section of radiusd.conf modcall: entering group authorize for request 3 modcall[authorize]: module "preprocess" returns ok for request 3 modcall[authorize]: module "chap" returns noop for request 3 modcall[authorize]: module "mschap" returns noop for request 3 rlm_realm: No '@' in User-Name = "mobile", looking up realm NULL rlm_realm: No such realm "NULL" modcall[authorize]: module "suffix" returns noop for request 3 users: Matched entry DEFAULT at line 185 users: Matched entry mobile at line 227 modcall[authorize]: module "files" returns ok for request 3 rlm_eap: EAP packet type response id 65 length 6 rlm_eap: No EAP Start, assuming it's an on-going EAP conversation modcall[authorize]: module "eap" returns updated for request 3 radius_xlat: 'mobile' rlm_sql (sql): sql_set_user escaped user --> 'mobile' radius_xlat: 'SELECT id,UserName,Attribute,Value,op FROM radcheck WHERE Username = 'mobile' ORDER BY id' rlm_sql (sql): Reserving sql socket id: 1 rlm_sql (sql): User mobile not found in radcheck radius_xlat: 'SELECT radgroupcheck.id,radgroupcheck.GroupName,radgroupcheck.Attribute,radgroupcheck.Value,radgroupcheck.op FROM radgroupcheck,usergroup WHERE usergroup.Username = 'mobile' AND usergroup.GroupName = radgroupcheck.GroupName ORDER BY radgroupcheck.id' radius_xlat: 'SELECT radgroupreply.id,radgroupreply.GroupName,radgroupreply.Attribute,radgroupreply.Value,radgroupreply.op FROM radgroupreply,usergroup WHERE usergroup.Username = 'mobile' AND usergroup.GroupName = radgroupreply.GroupName ORDER BY radgroupreply.id' rlm_sql (sql): Released sql socket id: 1 modcall[authorize]: module "sql" returns ok for request 3 rlm_ldap: - authorize rlm_ldap: performing user authorization for mobile radius_xlat: '(cn=mobile)' radius_xlat: 'ou=radius,o=uah,c=es' rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=radius,o=uah,c=es, with filter (cn=mobile) rlm_ldap: object not found or got ambiguous search result rlm_ldap: search failed rlm_ldap: ldap_release_conn: Release Id: 0 modcall[authorize]: module "ldap" returns notfound for request 3 modcall: group authorize returns updated for request 3 rad_check_password: Found Auth-Type EAP rad_check_password: Found Auth-Type EAP Warning: Found 2 auth-types on request for user 'mobile' auth: type "EAP" Processing the authenticate section of radiusd.conf modcall: entering group authenticate for request 3 rlm_eap: Request found, released from the list rlm_eap: EAP/tls rlm_eap: processing type tls rlm_eap_tls: Authenticate rlm_eap_tls: processing TLS rlm_eap_tls: Received EAP-TLS ACK message rlm_eap_tls: ack handshake fragment handler eaptls_verify returned 1 eaptls_process returned 13 modcall[authenticate]: module "eap" returns handled for request 3 modcall: group authenticate returns handled for request 3 Sending Access-Challenge of id 141 to 10.0.0.11:1812 EAP-Message = 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 EAP-Message = 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 EAP-Message = 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 EAP-Message = 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 EAP-Message = 0x060355040a1303756168310c300a060355040b130350 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x78ebcb20e451da232658604c0f20cec0 Finished request 3 Going to the next request Waking up in 6 seconds... rad_recv: Access-Request packet from host 10.0.0.11:1812, id=142, length=97 User-Name = "mobile" NAS-IP-Address = 10.0.0.11 Calling-Station-Id = "00-0E-35-5D-B5-25" State = 0x78ebcb20e451da232658604c0f20cec0 EAP-Message = 0x024200060d00 Message-Authenticator = 0x56e8c1640961c51340628c5e4113336e Processing the authorize section of radiusd.conf modcall: entering group authorize for request 4 modcall[authorize]: module "preprocess" returns ok for request 4 modcall[authorize]: module "chap" returns noop for request 4 modcall[authorize]: module "mschap" returns noop for request 4 rlm_realm: No '@' in User-Name = "mobile", looking up realm NULL rlm_realm: No such realm "NULL" modcall[authorize]: module "suffix" returns noop for request 4 users: Matched entry DEFAULT at line 185 users: Matched entry mobile at line 227 modcall[authorize]: module "files" returns ok for request 4 rlm_eap: EAP packet type response id 66 length 6 rlm_eap: No EAP Start, assuming it's an on-going EAP conversation modcall[authorize]: module "eap" returns updated for request 4 radius_xlat: 'mobile' rlm_sql (sql): sql_set_user escaped user --> 'mobile' radius_xlat: 'SELECT id,UserName,Attribute,Value,op FROM radcheck WHERE Username = 'mobile' ORDER BY id' rlm_sql (sql): Reserving sql socket id: 0 rlm_sql (sql): User mobile not found in radcheck radius_xlat: 'SELECT radgroupcheck.id,radgroupcheck.GroupName,radgroupcheck.Attribute,radgroupcheck.Value,radgroupcheck.op FROM radgroupcheck,usergroup WHERE usergroup.Username = 'mobile' AND usergroup.GroupName = radgroupcheck.GroupName ORDER BY radgroupcheck.id' radius_xlat: 'SELECT radgroupreply.id,radgroupreply.GroupName,radgroupreply.Attribute,radgroupreply.Value,radgroupreply.op FROM radgroupreply,usergroup WHERE usergroup.Username = 'mobile' AND usergroup.GroupName = radgroupreply.GroupName ORDER BY radgroupreply.id' rlm_sql (sql): Released sql socket id: 0 modcall[authorize]: module "sql" returns ok for request 4 rlm_ldap: - authorize rlm_ldap: performing user authorization for mobile radius_xlat: '(cn=mobile)' radius_xlat: 'ou=radius,o=uah,c=es' rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=radius,o=uah,c=es, with filter (cn=mobile) rlm_ldap: object not found or got ambiguous search result rlm_ldap: search failed rlm_ldap: ldap_release_conn: Release Id: 0 modcall[authorize]: module "ldap" returns notfound for request 4 modcall: group authorize returns updated for request 4 rad_check_password: Found Auth-Type EAP rad_check_password: Found Auth-Type EAP Warning: Found 2 auth-types on request for user 'mobile' auth: type "EAP" Processing the authenticate section of radiusd.conf modcall: entering group authenticate for request 4 rlm_eap: Request found, released from the list rlm_eap: EAP/tls rlm_eap: processing type tls rlm_eap_tls: Authenticate rlm_eap_tls: processing TLS rlm_eap_tls: Received EAP-TLS ACK message rlm_eap_tls: ack handshake fragment handler eaptls_verify returned 1 eaptls_process returned 13 modcall[authenticate]: module "eap" returns handled for request 4 modcall: group authenticate returns handled for request 4 Sending Access-Challenge of id 142 to 10.0.0.11:1812 EAP-Message = 0x0143040a0dc0000012d34b49312e302c060355040313254175746f72696461642064652043657274696669636163696f6e204175746f6d6174696361311d301b06092a864886f70d010901160e706b69406175742e7561682e6573820900ae7948d122becdf5300b0603551d0f04040302010630190603551d1104123010810e706b69406175742e7561682e657330190603551d1204123010810e706b69406175742e7561682e6573301106096086480186f8420101040403020007303606096086480186f842010d042916277561682043657274696669636174696f6e20417574686f72697479204365727469666963617465303b0603551d1f0434 EAP-Message = 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 EAP-Message = 0xa1e64c6b67ace010c40df18456750a07b145d67ef13512ae0dbf3fde758be09c2c3e53fb24890868c7f22ad030a5d0f3df0bd634d9e8e8351d51964ca5df26e24aa3f4a74d830f4645e16ad411b156739767522b7244160969a904cf63891afc5ac9459d4cad8db8b64ca656ea782dd67d0ba6397c850b4ab544e0c24a0e066e3f266495e3e89b6eeef4bd7fe4fe1f9b05472a08a09b0588096467cd7a35d1fbfef138d32b11d5c368bcf55e19a951ef6296e9c965534778e5d7356ca2c53536dd81a7f468be9f3323f5fc04ab2573de0c558d6db2257dac688bd6328956f068b6aba10649848a3a26d5181c13404a392ae7029b3c9c2261fde9afdd99 EAP-Message = 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 EAP-Message = 0x8c2cb604ad76c80fe5cfd0458b9b13b4f4b700010500 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x83a2b0b7088b72dae082b1c920aeb31a Finished request 4 Going to the next request Waking up in 6 seconds... rad_recv: Access-Request packet from host 10.0.0.11:1812, id=143, length=97 User-Name = "mobile" NAS-IP-Address = 10.0.0.11 Calling-Station-Id = "00-0E-35-5D-B5-25" State = 0x83a2b0b7088b72dae082b1c920aeb31a EAP-Message = 0x024300060d00 Message-Authenticator = 0x9da3b46acde71c0446afcb85102c4734 Processing the authorize section of radiusd.conf modcall: entering group authorize for request 5 modcall[authorize]: module "preprocess" returns ok for request 5 modcall[authorize]: module "chap" returns noop for request 5 modcall[authorize]: module "mschap" returns noop for request 5 rlm_realm: No '@' in User-Name = "mobile", looking up realm NULL rlm_realm: No such realm "NULL" modcall[authorize]: module "suffix" returns noop for request 5 users: Matched entry DEFAULT at line 185 users: Matched entry mobile at line 227 modcall[authorize]: module "files" returns ok for request 5 rlm_eap: EAP packet type response id 67 length 6 rlm_eap: No EAP Start, assuming it's an on-going EAP conversation modcall[authorize]: module "eap" returns updated for request 5 radius_xlat: 'mobile' rlm_sql (sql): sql_set_user escaped user --> 'mobile' radius_xlat: 'SELECT id,UserName,Attribute,Value,op FROM radcheck WHERE Username = 'mobile' ORDER BY id' rlm_sql (sql): Reserving sql socket id: 4 rlm_sql (sql): User mobile not found in radcheck radius_xlat: 'SELECT radgroupcheck.id,radgroupcheck.GroupName,radgroupcheck.Attribute,radgroupcheck.Value,radgroupcheck.op FROM radgroupcheck,usergroup WHERE usergroup.Username = 'mobile' AND usergroup.GroupName = radgroupcheck.GroupName ORDER BY radgroupcheck.id' radius_xlat: 'SELECT radgroupreply.id,radgroupreply.GroupName,radgroupreply.Attribute,radgroupreply.Value,radgroupreply.op FROM radgroupreply,usergroup WHERE usergroup.Username = 'mobile' AND usergroup.GroupName = radgroupreply.GroupName ORDER BY radgroupreply.id' rlm_sql (sql): Released sql socket id: 4 modcall[authorize]: module "sql" returns ok for request 5 rlm_ldap: - authorize rlm_ldap: performing user authorization for mobile radius_xlat: '(cn=mobile)' radius_xlat: 'ou=radius,o=uah,c=es' rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=radius,o=uah,c=es, with filter (cn=mobile) rlm_ldap: object not found or got ambiguous search result rlm_ldap: search failed rlm_ldap: ldap_release_conn: Release Id: 0 modcall[authorize]: module "ldap" returns notfound for request 5 modcall: group authorize returns updated for request 5 rad_check_password: Found Auth-Type EAP rad_check_password: Found Auth-Type EAP Warning: Found 2 auth-types on request for user 'mobile' auth: type "EAP" Processing the authenticate section of radiusd.conf modcall: entering group authenticate for request 5 rlm_eap: Request found, released from the list rlm_eap: EAP/tls rlm_eap: processing type tls rlm_eap_tls: Authenticate rlm_eap_tls: processing TLS rlm_eap_tls: Received EAP-TLS ACK message rlm_eap_tls: ack handshake fragment handler eaptls_verify returned 1 eaptls_process returned 13 modcall[authenticate]: module "eap" returns handled for request 5 modcall: group authenticate returns handled for request 5 Sending Access-Challenge of id 143 to 10.0.0.11:1812 EAP-Message = 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 EAP-Message = 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 EAP-Message = 0x34ac50a8eede1098634f56cb0b73cad65e4e1b76efe23d5db1a2b1278a7a70501e5d8ba32564f9324de034ac8ffc23e0fd7b37b482244517c7453c08291b0609d89e9d7c92611dbf2e857025bd98896bb72e15160301008b0d0000830403040102007c007a3078310b3009060355040613026573310c300a060355040a1303756168310c300a060355040b1303504b49312e302c060355040313254175746f72696461642064652043657274696669636163696f6e204175746f6d6174696361311d301b06092a864886f70d010901160e706b69406175742e7561682e65730e000000 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x8114badf17473ee2b9c1d2ac7940e28d Finished request 5 Going to the next request Waking up in 6 seconds... rad_recv: Access-Request packet from host 10.0.0.11:1812, id=144, length=1597 User-Name = "mobile" NAS-IP-Address = 10.0.0.11 Calling-Station-Id = "00-0E-35-5D-B5-25" State = 0x8114badf17473ee2b9c1d2ac7940e28d EAP-Message = 0x024405d80dc000000efe1603010de80b000de4000de10006403082063c30820424a003020102020104300d06092a864886f70d01010505003078310b3009060355040613026573310c300a060355040a1303756168310c300a060355040b1303504b49312e302c060355040313254175746f72696461642064652043657274696669636163696f6e204175746f6d6174696361311d301b06092a864886f70d010901160e706b69406175742e7561682e6573301e170d3035303633303131333833345a170d3039303632383131333833345a304b310b3009060355040613026573310c300a060355040a13037561683110300e060355040b1307416c75 EAP-Message = 0x6d6e6f733110300e06035504031307436c69656e7465310a3008060355040513013430819f300d06092a864886f70d010101050003818d00308189028181009d475e9547b81afa9cfa087cef13d6e90dfaa1eef56fdef756fabdf8685ae8293f01f3c105e6c6ca1c14ac6cb4f92322deb00352b2842068d879c3683562883efa5eadddd275c269593afa9a5d8920b43d413118127213b8674a8837f97730d883f0c79fa54c06f67baf2a39a200106544fd498c58344b8bc20a9940ed10386d0203010001a38202803082027c30090603551d130402300030430603551d20043c303a300606042a030304303006042a0303053028302606082b06010505 EAP-Message = 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 EAP-Message = 0x040b1303504b49312e302c060355040313254175746f72696461642064652043657274696669636163696f6e204175746f6d6174696361311d301b06092a864886f70d010901160e706b69406175742e7561682e6573820900ae7948d122becdf5301d0603551d11041630148112636c69656e7465407072756562612e636f6d30190603551d1204123010810e706b69406175742e7561682e6573303906096086480186f8420104042c162a687474703a2f2f6f626977616e2e6175742e7561682e65732f7075622f63726c2f636163726c2e63726c303906096086480186f8420103042c162a687474703a2f2f6f626977616e2e6175742e7561682e EAP-Message = 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 EAP-Message = 0xd799d71a479e34d17ea091468dbe0f560e7a44ce6d74368bc9dcca4257935e03bb9d755e3a4e178875ca51a32e7019d207268191a812745e2e5cb4b91224776f9aef9f6397ac485da2cd24a0d1c25e02d1f2828a21cbc47c762f86aeb4b44a5af71f013ded4d3a54cba5a49851218577af1c2b90cd27f3b5065a409f3e2644a7425ed3dc17d15a630f860fcc216813bdb0acb2b507f5c8479b280a110eecb858f0ef077a76f14107742ea064e02045789ded712b3eb8aadd9c1209e10757f25e14b900e4e8a111616e66697366586bf57a6f5fa79845021bde33efec2dddc95f3529b3a04ea2b8 Message-Authenticator = 0x8b8598358880bd370a2468c64421fec9 Processing the authorize section of radiusd.conf modcall: entering group authorize for request 6 modcall[authorize]: module "preprocess" returns ok for request 6 modcall[authorize]: module "chap" returns noop for request 6 modcall[authorize]: module "mschap" returns noop for request 6 rlm_realm: No '@' in User-Name = "mobile", looking up realm NULL rlm_realm: No such realm "NULL" modcall[authorize]: module "suffix" returns noop for request 6 users: Matched entry DEFAULT at line 185 users: Matched entry mobile at line 227 modcall[authorize]: module "files" returns ok for request 6 rlm_eap: EAP packet type response id 68 length 253 rlm_eap: No EAP Start, assuming it's an on-going EAP conversation modcall[authorize]: module "eap" returns updated for request 6 radius_xlat: 'mobile' rlm_sql (sql): sql_set_user escaped user --> 'mobile' radius_xlat: 'SELECT id,UserName,Attribute,Value,op FROM radcheck WHERE Username = 'mobile' ORDER BY id' rlm_sql (sql): Reserving sql socket id: 3 rlm_sql (sql): User mobile not found in radcheck radius_xlat: 'SELECT radgroupcheck.id,radgroupcheck.GroupName,radgroupcheck.Attribute,radgroupcheck.Value,radgroupcheck.op FROM radgroupcheck,usergroup WHERE usergroup.Username = 'mobile' AND usergroup.GroupName = radgroupcheck.GroupName ORDER BY radgroupcheck.id' radius_xlat: 'SELECT radgroupreply.id,radgroupreply.GroupName,radgroupreply.Attribute,radgroupreply.Value,radgroupreply.op FROM radgroupreply,usergroup WHERE usergroup.Username = 'mobile' AND usergroup.GroupName = radgroupreply.GroupName ORDER BY radgroupreply.id' rlm_sql (sql): Released sql socket id: 3 modcall[authorize]: module "sql" returns ok for request 6 rlm_ldap: - authorize rlm_ldap: performing user authorization for mobile radius_xlat: '(cn=mobile)' radius_xlat: 'ou=radius,o=uah,c=es' rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=radius,o=uah,c=es, with filter (cn=mobile) rlm_ldap: object not found or got ambiguous search result rlm_ldap: search failed rlm_ldap: ldap_release_conn: Release Id: 0 modcall[authorize]: module "ldap" returns notfound for request 6 modcall: group authorize returns updated for request 6 rad_check_password: Found Auth-Type EAP rad_check_password: Found Auth-Type EAP Warning: Found 2 auth-types on request for user 'mobile' auth: type "EAP" Processing the authenticate section of radiusd.conf modcall: entering group authenticate for request 6 rlm_eap: Request found, released from the list rlm_eap: EAP/tls rlm_eap: processing type tls rlm_eap_tls: Authenticate rlm_eap_tls: processing TLS rlm_eap_tls: Received EAP-TLS First Fragment of the message eaptls_verify returned 9 eaptls_process returned 13 modcall[authenticate]: module "eap" returns handled for request 6 modcall: group authenticate returns handled for request 6 Sending Access-Challenge of id 144 to 10.0.0.11:1812 EAP-Message = 0x014500060d00 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x15011ed049f30b857ce6683156d2b2b9 Finished request 6 Going to the next request Waking up in 6 seconds... rad_recv: Access-Request packet from host 10.0.0.11:1812, id=145, length=1597 User-Name = "mobile" NAS-IP-Address = 10.0.0.11 Calling-Station-Id = "00-0E-35-5D-B5-25" State = 0x15011ed049f30b857ce6683156d2b2b9 EAP-Message = 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 EAP-Message = 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 EAP-Message = 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 EAP-Message = 0x5f44b526317671e633875e40182a7c592a9ad55a00a4c08d591419942e5a590d896e1c351afd3515a5200be219f3e854521b8d5c10f5cfe633975c1e38cf590d7cdf325d53239b88cd483764556dbda3bcb1e8280d01cd782ca228d925e5bec5e25065d7c62fed53214587a49a051ad92f251a131324e4c646461c7b780b7e322403708a758df8d5711d3c609efa5b62f47bc1c4e42f7b38970d944198545cff44fccd58787fc6edbbbd243c0d876c1fe3db89a6fd76f1276faa7a4fddbb7ab54078d69ea6c11289fb032b6d0b58f293e2133dafc7565b9c54d68bcc78d8a2733af103969ba0a0f7b08d40030214f70203010001a38202223082021e30 EAP-Message = 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 EAP-Message = 0x2e7561682e657330190603551d1204123010810e706b69406175742e7561682e6573301106096086480186f8420101040403020007303606096086480186f842010d042916277561682043657274696669636174696f6e20417574686f72697479204365727469666963617465303b0603551d1f043430323030a02ea02c862a687474703a2f2f6f626977616e2e6175742e7561682e65732f7075622f63726c2f636163726c2e63726c303906096086480186f8420104042c162a687474703a2f2f6f626977616e2e6175742e7561682e65732f7075622f63726c2f636163726c2e63726c3039 Message-Authenticator = 0xc5d316d802ac60ec275aff67c255312d Processing the authorize section of radiusd.conf modcall: entering group authorize for request 7 modcall[authorize]: module "preprocess" returns ok for request 7 modcall[authorize]: module "chap" returns noop for request 7 modcall[authorize]: module "mschap" returns noop for request 7 rlm_realm: No '@' in User-Name = "mobile", looking up realm NULL rlm_realm: No such realm "NULL" modcall[authorize]: module "suffix" returns noop for request 7 users: Matched entry DEFAULT at line 185 users: Matched entry mobile at line 227 modcall[authorize]: module "files" returns ok for request 7 rlm_eap: EAP packet type response id 69 length 253 rlm_eap: No EAP Start, assuming it's an on-going EAP conversation modcall[authorize]: module "eap" returns updated for request 7 radius_xlat: 'mobile' rlm_sql (sql): sql_set_user escaped user --> 'mobile' radius_xlat: 'SELECT id,UserName,Attribute,Value,op FROM radcheck WHERE Username = 'mobile' ORDER BY id' rlm_sql (sql): Reserving sql socket id: 2 rlm_sql (sql): User mobile not found in radcheck radius_xlat: 'SELECT radgroupcheck.id,radgroupcheck.GroupName,radgroupcheck.Attribute,radgroupcheck.Value,radgroupcheck.op FROM radgroupcheck,usergroup WHERE usergroup.Username = 'mobile' AND usergroup.GroupName = radgroupcheck.GroupName ORDER BY radgroupcheck.id' radius_xlat: 'SELECT radgroupreply.id,radgroupreply.GroupName,radgroupreply.Attribute,radgroupreply.Value,radgroupreply.op FROM radgroupreply,usergroup WHERE usergroup.Username = 'mobile' AND usergroup.GroupName = radgroupreply.GroupName ORDER BY radgroupreply.id' rlm_sql (sql): Released sql socket id: 2 modcall[authorize]: module "sql" returns ok for request 7 rlm_ldap: - authorize rlm_ldap: performing user authorization for mobile radius_xlat: '(cn=mobile)' radius_xlat: 'ou=radius,o=uah,c=es' rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=radius,o=uah,c=es, with filter (cn=mobile) rlm_ldap: object not found or got ambiguous search result rlm_ldap: search failed rlm_ldap: ldap_release_conn: Release Id: 0 modcall[authorize]: module "ldap" returns notfound for request 7 modcall: group authorize returns updated for request 7 rad_check_password: Found Auth-Type EAP rad_check_password: Found Auth-Type EAP Warning: Found 2 auth-types on request for user 'mobile' auth: type "EAP" Processing the authenticate section of radiusd.conf modcall: entering group authenticate for request 7 rlm_eap: Request found, released from the list rlm_eap: EAP/tls rlm_eap: processing type tls rlm_eap_tls: Authenticate rlm_eap_tls: processing TLS rlm_eap_tls: More fragments to follow eaptls_verify returned 10 eaptls_process returned 13 modcall[authenticate]: module "eap" returns handled for request 7 modcall: group authenticate returns handled for request 7 Sending Access-Challenge of id 145 to 10.0.0.11:1812 EAP-Message = 0x014600060d00 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x60952358c960e539d5816741349ddde1 Finished request 7 Going to the next request Waking up in 6 seconds... rad_recv: Access-Request packet from host 10.0.0.11:1812, id=146, length=965 User-Name = "mobile" NAS-IP-Address = 10.0.0.11 Calling-Station-Id = "00-0E-35-5D-B5-25" State = 0x60952358c960e539d5816741349ddde1 EAP-Message = 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 EAP-Message = 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 EAP-Message = 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 EAP-Message = 0x720647843d80125169fa1fea2a4cf59511da7c7cfc768b88188107033e7fdc7f6491fbd5084fbff1b102260ef4847c81a9e214030100010116030100302a8a7334eaa46ebabd33a1663113ab211dda71bdb26041325de1a11576c410e73b9812ad71e298f238b80452094c7652 Message-Authenticator = 0x86535dbf2d2b52864402b8f0e5619942 Processing the authorize section of radiusd.conf modcall: entering group authorize for request 8 modcall[authorize]: module "preprocess" returns ok for request 8 modcall[authorize]: module "chap" returns noop for request 8 modcall[authorize]: module "mschap" returns noop for request 8 rlm_realm: No '@' in User-Name = "mobile", looking up realm NULL rlm_realm: No such realm "NULL" modcall[authorize]: module "suffix" returns noop for request 8 users: Matched entry DEFAULT at line 185 users: Matched entry mobile at line 227 modcall[authorize]: module "files" returns ok for request 8 rlm_eap: EAP packet type response id 70 length 253 rlm_eap: No EAP Start, assuming it's an on-going EAP conversation modcall[authorize]: module "eap" returns updated for request 8 radius_xlat: 'mobile' rlm_sql (sql): sql_set_user escaped user --> 'mobile' radius_xlat: 'SELECT id,UserName,Attribute,Value,op FROM radcheck WHERE Username = 'mobile' ORDER BY id' rlm_sql (sql): Reserving sql socket id: 1 rlm_sql (sql): User mobile not found in radcheck radius_xlat: 'SELECT radgroupcheck.id,radgroupcheck.GroupName,radgroupcheck.Attribute,radgroupcheck.Value,radgroupcheck.op FROM radgroupcheck,usergroup WHERE usergroup.Username = 'mobile' AND usergroup.GroupName = radgroupcheck.GroupName ORDER BY radgroupcheck.id' radius_xlat: 'SELECT radgroupreply.id,radgroupreply.GroupName,radgroupreply.Attribute,radgroupreply.Value,radgroupreply.op FROM radgroupreply,usergroup WHERE usergroup.Username = 'mobile' AND usergroup.GroupName = radgroupreply.GroupName ORDER BY radgroupreply.id' rlm_sql (sql): Released sql socket id: 1 modcall[authorize]: module "sql" returns ok for request 8 rlm_ldap: - authorize rlm_ldap: performing user authorization for mobile radius_xlat: '(cn=mobile)' radius_xlat: 'ou=radius,o=uah,c=es' rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=radius,o=uah,c=es, with filter (cn=mobile) rlm_ldap: object not found or got ambiguous search result rlm_ldap: search failed rlm_ldap: ldap_release_conn: Release Id: 0 modcall[authorize]: module "ldap" returns notfound for request 8 modcall: group authorize returns updated for request 8 rad_check_password: Found Auth-Type EAP rad_check_password: Found Auth-Type EAP Warning: Found 2 auth-types on request for user 'mobile' auth: type "EAP" Processing the authenticate section of radiusd.conf modcall: entering group authenticate for request 8 rlm_eap: Request found, released from the list rlm_eap: EAP/tls rlm_eap: processing type tls rlm_eap_tls: Authenticate rlm_eap_tls: processing TLS eaptls_verify returned 7 rlm_eap_tls: Done initial handshake rlm_eap_tls: <<< TLS 1.0 Handshake [length 0de8], Certificate chain-depth=1, error=0 --> User-Name = mobile --> BUF-Name = Autoridad de Certificacion Automatica --> subject = /C=es/O=uah/OU=PKI/CN=Autoridad de Certificacion Automatica/emailAddress=pki(a)aut.uah.es --> issuer = /C=es/O=uah/OU=PKI/CN=Autoridad de Certificacion Automatica/emailAddress=pki(a)aut.uah.es --> verify return:1 chain-depth=0, error=0 --> User-Name = mobile --> BUF-Name = Cliente --> subject = /C=es/O=uah/OU=Alumnos/CN=Cliente/serialNumber=4 --> issuer = /C=es/O=uah/OU=PKI/CN=Autoridad de Certificacion Automatica/emailAddress=pki(a)aut.uah.es --> verify return:1 TLS_accept: SSLv3 read client certificate A rlm_eap_tls: <<< TLS 1.0 Handshake [length 0046], ClientKeyExchange TLS_accept: SSLv3 read client key exchange A rlm_eap_tls: <<< TLS 1.0 Handshake [length 0086], CertificateVerify TLS_accept: SSLv3 read certificate verify A rlm_eap_tls: <<< TLS 1.0 ChangeCipherSpec [length 0001] rlm_eap_tls: <<< TLS 1.0 Handshake [length 0010], Finished TLS_accept: SSLv3 read finished A rlm_eap_tls: >>> TLS 1.0 ChangeCipherSpec [length 0001] TLS_accept: SSLv3 write change cipher spec A rlm_eap_tls: >>> TLS 1.0 Handshake [length 0010], Finished TLS_accept: SSLv3 write finished A TLS_accept: SSLv3 flush data (other): SSL negotiation finished successfully SSL Connection Established eaptls_process returned 13 modcall[authenticate]: module "eap" returns handled for request 8 modcall: group authenticate returns handled for request 8 Sending Access-Challenge of id 146 to 10.0.0.11:1812 EAP-Message = 0x014700450d800000003b14030100010116030100306e143f76c8cc466fb5bd2e30eae300820b579ca7d08e6c086fbf2ea0c05a80ab19014fa8ebec699fd9beb87723a81225 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x15ef8e9ca16373521a0d577ee1ced6ba Finished request 8 Going to the next request Waking up in 6 seconds...

1 0

rlm_eap module trouble!
by Andm M 13 Jul '05

13 Jul '05

Hello! I'm trying to compile FreeRadius 1.0.4 on Windows XP machine under Cygwin, but the EAP module doesn't work. I'm compile server with --disable-shared flag. When radiusd -X executes it says that rlm_eap is failded to link and unknown error occur. When I comment all eap definitions in radiusd.conf then all OK. Could anyone help me on this, I am totally new to FreeRadius. Thanks, Andrew Melovatsky

1 0

FreeRadius+Active Directory+Cisco Switch
by Nikolai Belstein 13 Jul '05

13 Jul '05

Hello everyone! Please help me! I need to authorise cisco ports, using Radius. Please tell me, witch parameters I need to put in radiusd.conf for using Active Directory database. Thanks a lot! Nikolai.

1 0

RE: sql counter clarification and issues
by Ross Tsolakidis 13 Jul '05

13 Jul '05

Thanks for responding Marcin, just to double check: I added those details into radgroupcheck: mysql> select * from radgroupcheck; +----+-----------+---------------------+----+-------+ | id | GroupName | Attribute | op | Value | +----+-----------+---------------------+----+-------+ | 1 | 24Hours | Max-Daily-Session | := | 86400 | | 2 | 24Hours | Max-Weekly-Session | := | 86400 | | 3 | 24Hours | Max-Monthly-Session | := | 86400 | | 4 | 24Hours | Max-All-Session | := | 86400 | | 5 | 10Mins | Max-Daily-Session | := | 600 | | 6 | 10Mins | Max-Weekly-Session | := | 600 | | 7 | 10Mins | Max-Monthly-Session | := | 600 | | 8 | 10Mins | Max-All-Session | := | 600 | +----+-----------+---------------------+----+-------+ 8 rows in set (0.00 sec) mysql> == My sqlcounter.conf is exactly the same. I have added this: $INCLUDE ${confdir}/sqlcounter.conf Into the radiusd.conf == When I fire up radius in debug mode I get these messages for sqlcounter: Module: Loaded SQL Counter sqlcounter: counter-name = "Daily-Session-Time" sqlcounter: check-name = "Max-Daily-Session" sqlcounter: key = "User-Name" sqlcounter: sqlmod-inst = "sql" sqlcounter: query = "SELECT SUM(AcctSessionTime - GREATEST((%b - UNIX_TIMESTAMP(AcctStartTime)), 0)) FROM radacct WHERE UserName='%{%k}' AND UNIX_TIMESTAMP(AcctStartTime) + AcctSessionTime > '%b'" sqlcounter: reset = "daily" rlm_sqlcounter: Counter attribute Daily-Session-Time is number 1671 rlm_sqlcounter: Check attribute Max-Daily-Session is number 1672 rlm_sqlcounter: Current Time: 1121220718 [2005-07-13 12:11:58], Next reset 1121263200 [2005-07-14 00:00:00] rlm_sqlcounter: Current Time: 1121220718 [2005-07-13 12:11:58], Prev reset 1121176800 [2005-07-13 00:00:00] Module: Instantiated sqlcounter (dailycounter) == I read the experimental.conf but I can't seem to understand where the counters are reset, which table ? Could you give me an example of the table so I can see what it should look like ? (daily totals) I don't really have any need to disconnect people after a certain period of time, just need daily and monthly totals. Thanks again, greatly appreciated ! :) Regards, -- Ross -----Original Message----- From: Marcin Jessa [mailto:lists@yazzy.org] Sent: Tuesday, 12 July 2005 6:03 PM To: FreeRadius users mailing list Cc: Ross Tsolakidis Subject: Re: sql counter clarification and issues On Tue, 12 Jul 2005 15:21:52 +1000 "Ross Tsolakidis" <Ross.Tsolakidis(a)day3.com.au> wrote: > Ok, now I'm really confused :( > > Can someone please clarify exactly what does the sqlcounter module do ? > Basically I need to calculate the data on a daily basis for each user. sqlcounter works fine. Your radgroupcheck or radcheck needs to have the same attributes you have in your sqlcounter config. Check out mine: http://www.yazzy.org/configs/linux/freeradius/sqlcounter.conf mysql> select * from radgroupcheck; +----+-----------+---------------------+----+-------+ | id | GroupName | Attribute | op | Value | +----+-----------+---------------------+----+-------+ | 1 | 24hours | Max-Daily-Session | := | 86400 | | 2 | 24hours | Max-Weekly-Session | := | 86400 | | 3 | 24hours | Max-Monthly-Session | := | 86400 | | 4 | 24hours | Max-All-Session | := | 86400 | | 5 | 10mins | Max-Daily-Session | := | 600 | | 6 | 10mins | Max-Weekly-Session | := | 600 | | 7 | 10mins | Max-Monthly-Session | := | 600 | | 8 | 10mins | Max-All-Session | := | 600 | +----+-----------+---------------------+----+-------+ 8 rows in set (0.00 sec) Read experimental.conf, it describes the module. It count's user's online time stored in the raddacct table and based on that info allows user to log in if her allowed session time is not exceeded. This can be done on daily, weekly, monthly or total basis. > Thanks for your patience :) Read former postings to the list describing the behaviour and functionality of the module. People tend to be more patient if they know you did some work on your own. Cheers, Marcin Jessa > > -----Original Message----- > From: freeradius-users-bounces(a)lists.freeradius.org > [mailto:freeradius-users-bounces@lists.freeradius.org] On Behalf Of > Ross Tsolakidis > Sent: Tuesday, 5 July 2005 2:14 PM > To: FreeRadius users mailing list > Subject: RE: sql counter clarification and issues > > Yes the server is receiving accounting packets. > The SQL rows are updating every 5 mins, (I have the NAS set to send > accounting packets every 5 mins). > > I run it in debug mode, I see: > Module: Loaded SQL Counter > sqlcounter: counter-name = "Daily-Session-Time" > sqlcounter: check-name = "Max-Daily-Session" > sqlcounter: key = "User-Name" > sqlcounter: sqlmod-inst = "sqlcca3" > sqlcounter: query = "SELECT SUM(AcctSessionTime - GREATEST((%b - > UNIX_TIMESTAMP(AcctStartTime)), 0)) FROM radacct WHERE UserName='%{%k}' > AND UNIX_TIMESTAMP(AcctStartTime) + AcctSessionTime > '%b'" > sqlcounter: reset = "1h" > rlm_sqlcounter: Counter attribute Daily-Session-Time is number 1671 > rlm_sqlcounter: Check attribute Max-Daily-Session is number 1672 > rlm_sqlcounter: num=1, last=h > rlm_sqlcounter: Current Time: 1120532709 [2005-07-05 13:05:09], Next > reset 1120536000 [2005-07-05 14:00:00] > rlm_sqlcounter: num=1, last=h > rlm_sqlcounter: Current Time: 1120532709 [2005-07-05 13:05:09], Prev > reset 1120532400 [2005-07-05 13:00:00] > Module: Instantiated sqlcounter (dailycounter) > > But no reset. > > Does anyone have this working, if so, what am I looking for, what am I > supposed to see ? > > Thanks :) > > Regards, > -- > Ross > > -----Original Message----- > From: freeradius-users-bounces(a)lists.freeradius.org > [mailto:freeradius-users-bounces@lists.freeradius.org] On Behalf Of > Alan DeKok > Sent: Tuesday, 5 July 2005 2:05 AM > To: FreeRadius users mailing list > Subject: Re: sql counter clarification and issues > > "Ross Tsolakidis" <Ross.Tsolakidis(a)day3.com.au> wrote: > > At midnight every night will it begin a new row in SQL ? > > I don't know, I've never used the module. > > > Because at the moment there are no new rows being created, no > > counters > > > being reset. > > Is the server receiving accounting packets? > > Run it in debug mode with "reset=hour", and spend some time looking > at what it's doing. > > Alan DeKok. > - > List info/subscribe/unsubscribe? See > http://www.freeradius.org/list/users.html > > - > List info/subscribe/unsubscribe? See > http://www.freeradius.org/list/users.html > > - > List info/subscribe/unsubscribe? See > http://www.freeradius.org/list/users.html

2 1

Re: eDirectory Issues
by Sayantan Bhowmick 13 Jul '05

13 Jul '05

Hi, Comments inlined. On Tue, 2005-07-12 at 11:15 -0700, jp(a)joshmp.com wrote: > I appologize in advance, but I am new to FreeRADIUS and RADIUS in general. > > Here is my setup: > - Server with FreeRADIUS 1.0.4 --with-edir on FreeBSD 4.11 > - Server with NetWare 6.5.4 > > Here is what I am trying to accomplish: > - Get FreeRADIUS to authenticate VPN users (Cisco VPN Contentrator) to LDAP > database in NetWare tree. > > Here is what I DON'T want to do: > - Mess with eDirectory (profiles, extending the schema, etc.) > > Basically, when this configuration is moved into production, FreeRADIUS would > authenticate users who IDs already exist in a complex, mature NetWare eDir tree. > I don't want to mess with Universal Passwords, extending the schema, etc. I > have already sucessfully configured the Cisco VPN Concentrator to authenticate > users using FreeRADIUS and the UNIX users list. However, I can't get FreeRADIUS > to successfully query the LDAP database on the NetWare server. > > I have been through Novell's documentation, but their docs include building > RADIUS profiles, extending the schema, etc. This is something that I am not > going to be able to do. I have also been up and down the web, FreeRADIUS mail > lists, docs, etc. I have found threads where it is mentioned that you can get > FreeRADIUS to authenticate users to a NetWare LDAP directory using cleartext, > but I have not been able to do this myself. > > I would like to take this in stages: > 1. Succesfully query LDAP without security (with the assumption that this would > be the easiest first step). The debug output shows that FreeRADIUS is already doing this, > 2. Get FreeRADIUS to query LDAP securely. This also can be configured. > > Below you will find the following: > - Text from radiusd.conf file > - Output from radiusd -X > - Text from radius.log file > <- Snipped,.... > # Lightweight Directory Access Protocol (LDAP) > # > # This module definition allows you to use LDAP for > # authorization and authentication (Auth-Type := LDAP) > # > # See doc/rlm_ldap for description of configuration options > # and sample authorize{} and authenticate{} blocks > ldap { > server = "10.1.1.71" > identity = "cn=admin,o=radius" > password = pass > basedn = "o=radius" > filter = "(uid=%{Stripped-User-Name:-%{User-Name}})" > base_filter = "(objectclass=radiusprofile)" > > # set this to 'yes' to use TLS encrypted connections > # to the LDAP database by using the StartTLS extended > # operation. > # The StartTLS operation is supposed to be used with normal > # ldap connections instead of using ldaps (port 689) connections > start_tls = no Set start_tls = yes for making a secure connection to eDirectory. > > # tls_cacertfile = /path/to/cacert.pem Set the path to eDirectory CA cert here. > # tls_cacertdir = /path/to/ca/dir/ > # tls_certfile = /path/to/radius.crt > # tls_keyfile = /path/to/radius.key > # tls_randfile = /path/to/rnd > # tls_require_cert = "demand" > > # default_profile = "cn=radprofile,ou=dialup,o=My Org,c=UA" > # profile_attribute = "radiusProfileDn" > # access_attr = "dialupAccess" > > # Mapping of RADIUS dictionary attributes to LDAP > # directory attributes. > dictionary_mapping = ${raddbdir}/ldap.attrmap > > ldap_connections_number = 5 > > # > # NOTICE: The password_header directive is NOT case insensitive > # > # password_header = "{clear}" > # > # Set: > password_attribute = nspmPassword Set password_attribute to anything other than nspmPassword or comment out this attribute. This will make sure FreeRADIUS does not try to read Universal Password. > # > # to get the user's password from a Novell eDirectory > # backend. This will work *only if* freeRADIUS is > # configured to build with --with-edir option. > # > # > # The server can usually figure this out on its own, and pull > # the correct User-Password or NT-Password from the database. > # > # Note that NT-Passwords MUST be stored as a 32-digit hex > # string, and MUST start off with "0x", such as: > # > # 0x000102030405060708090a0b0c0d0e0f > # > # Without the leading "0x", NT-Passwords will not work. > # This goes for NT-Passwords stored in SQL, too. > # > # password_attribute = userPassword > # > # Un-comment the following to disable Novell eDirectory account > # policy check and intruder detection. This will work *only if* > # FreeRADIUS is configured to build with --with-edir option. > # > edir_account_policy_check=yes > # > # groupname_attribute = cn > # groupmembership_filter = > "(|(&(objectClass=GroupOfNames)(member=%{Ldap-UserDn}))(&(objectClass=GroupOfUniqueNames)(uniquemember=%{Ldap-UserDn})))" > # groupmembership_attribute = radiusGroupName > timeout = 4 > timelimit = 3 > net_timeout = 1 > # compare_check_items = yes > # do_xlat = yes > # access_attr_used_for_allow = yes > } > <-Snipped.... > Ready to process requests. > rad_recv: Access-Request packet from host 127.0.0.1:2302, id=75, length=57 > User-Name = "admin" > User-Password = "pass" > NAS-IP-Address = 255.255.255.255 > NAS-Port = 10 > Processing the authorize section of radiusd.conf > modcall: entering group authorize for request 0 > modcall[authorize]: module "preprocess" returns ok for request 0 > modcall[authorize]: module "chap" returns noop for request 0 > modcall[authorize]: module "mschap" returns noop for request 0 > rlm_realm: No '@' in User-Name = "admin", looking up realm NULL > rlm_realm: No such realm "NULL" > modcall[authorize]: module "suffix" returns noop for request 0 > rlm_eap: No EAP-Message, not doing EAP > modcall[authorize]: module "eap" returns noop for request 0 > users: Matched entry DEFAULT at line 152 > modcall[authorize]: module "files" returns ok for request 0 > rlm_ldap: - authorize > rlm_ldap: performing user authorization for admin > radius_xlat: '(uid=admin)' > radius_xlat: 'o=radius' > rlm_ldap: ldap_get_conn: Checking Id: 0 > rlm_ldap: ldap_get_conn: Got Id: 0 > rlm_ldap: attempting LDAP reconnection > rlm_ldap: (re)connect to 10.1.1.71:389, authentication 0 > rlm_ldap: bind as cn=admin,o=radius/pass to 10.1.1.71:389 > rlm_ldap: waiting for bind result ... > rlm_ldap: Bind was successful > rlm_ldap: performing search in o=radius, with filter (uid=admin) As you can see FreeRADIUS is already querying eDirectory for user information. > rlm_ldap: Error reading Universal Password.Return Code = 80 See comments on password_attribute. > rlm_ldap: looking for check items in directory... > rlm_ldap: looking for reply items in directory... > rlm_ldap: user admin authorized to use remote access > rlm_ldap: ldap_release_conn: Release Id: 0 > modcall[authorize]: module "ldap" returns ok for request 0 > modcall: group authorize returns ok for request 0 > rad_check_password: Found Auth-Type System The Auth-Type is set to System. I reckon this is done by one of the default entries in users file. What is the authentication mechanism you want to use? If you want to use authentication methods like CHAP, MS-CHAP, EAP etc you will have to enable Universal Password. However if you just want to authenticate against eDirectory with plain text password then you need not read Universal Password. You must enable the ldap module in the authenticate section. > auth: type "System" > Processing the authenticate section of radiusd.conf > modcall: entering group authenticate for request 0 > modcall[authenticate]: module "unix" returns notfound for request 0 > modcall: group authenticate returns notfound for request 0 > auth: Failed to validate the user. > Processing the post-auth section of radiusd.conf > modcall: entering group Post-Auth-Type for request 0 > modcall[post-auth]: module "ldap" returns noop for request 0 > modcall: group Post-Auth-Type returns noop for request 0 > Delaying request 0 for 1 seconds > Finished request 0 > Going to the next request > --- Walking the entire request list --- > Waking up in 1 seconds... > --- Walking the entire request list --- > Waking up in 1 seconds... > --- Walking the entire request list --- > Sending Access-Reject of id 75 to 127.0.0.1:2302 > Waking up in 4 seconds... > --- Walking the entire request list --- > Cleaning up request 0 ID 75 with timestamp 42d39d5d > Nothing to do. Sleeping until we see a request. > -----END RADIUSD DEBUG----- > > The line that I find disturbing is the "error reading Universal Password" line. > I assume that I must edit my config in some way so that FreeRADIUS is not > attempting to read a Universal Password, or somehow tells NLDAP not to send a > Universal Password. Hope this helps. Get back to me in case you have any further queries. -Sayantan.

1 0

Win 2000 -> Cisco 3550 -> freeradius
by Michael Langer 13 Jul '05

13 Jul '05

Hi, i try to install 802.1x enviroment (windows 2000 -> Cisco Switch -> freeradius). The switch only allow auhtentificated clients (windows) to send packets to the intranet. All works well, but all the time freeradius reject because no User-Password, but i insert one in the login screen. System: Freeradius 1.0.4, Windows 2000, Cisco 3550 Log: rad_recv: Access-Request packet from host 192.168.1.3:1812, id=6, length=98 NAS-IP-Address = 192.168.1.3 NAS-Port = 50010 NAS-Port-Type = Ethernet User-Name = "test" Calling-Station-Id = "00-04-75-DA-4C-C8" Service-Type = Framed-User EAP-Message = 0x020100090174657374 Message-Authenticator = 0x05ada6b6c1de489b42a378805df01aac Processing the authorize section of radiusd.conf modcall: entering group authorize for request 1 modcall[authorize]: module "preprocess" returns ok for request 1 modcall[authorize]: module "chap" returns noop for request 1 modcall[authorize]: module "mschap" returns noop for request 1 rlm_realm: No '@' in User-Name = "test", looking up realm NULL rlm_realm: No such realm "NULL" modcall[authorize]: module "suffix" returns noop for request 1 rlm_eap: EAP packet type response id 1 length 9 rlm_eap: No EAP Start, assuming it's an on-going EAP conversation modcall[authorize]: module "eap" returns updated for request 1 users: Matched entry test at line 54 modcall[authorize]: module "files" returns ok for request 1 modcall: group authorize returns updated for request 1 rad_check_password: Found Auth-Type Local auth: type Local auth: No User-Password or CHAP-Password attribute in the request auth: Failed to validate the user. User Entry: test Auth-Type := Local, User-Passwort == "xxx" Service-Type = Framed-User And i insert the password in the login screen (windows client) Thx for help and hints -- Weitersagen: GMX DSL-Flatrates mit Tempo-Garantie! Ab 4,99 Euro/Monat: http://www.gmx.net/de/go/dsl

3 5

eDirectory Issues
by jp＠joshmp.com 13 Jul '05

13 Jul '05

I appologize in advance, but I am new to FreeRADIUS and RADIUS in general. Here is my setup: - Server with FreeRADIUS 1.0.4 --with-edir on FreeBSD 4.11 - Server with NetWare 6.5.4 Here is what I am trying to accomplish: - Get FreeRADIUS to authenticate VPN users (Cisco VPN Contentrator) to LDAP database in NetWare tree. Here is what I DON'T want to do: - Mess with eDirectory (profiles, extending the schema, etc.) Basically, when this configuration is moved into production, FreeRADIUS would authenticate users who IDs already exist in a complex, mature NetWare eDir tree. I don't want to mess with Universal Passwords, extending the schema, etc. I have already sucessfully configured the Cisco VPN Concentrator to authenticate users using FreeRADIUS and the UNIX users list. However, I can't get FreeRADIUS to successfully query the LDAP database on the NetWare server. I have been through Novell's documentation, but their docs include building RADIUS profiles, extending the schema, etc. This is something that I am not going to be able to do. I have also been up and down the web, FreeRADIUS mail lists, docs, etc. I have found threads where it is mentioned that you can get FreeRADIUS to authenticate users to a NetWare LDAP directory using cleartext, but I have not been able to do this myself. I would like to take this in stages: 1. Succesfully query LDAP without security (with the assumption that this would be the easiest first step). 2. Get FreeRADIUS to query LDAP securely. Below you will find the following: - Text from radiusd.conf file - Output from radiusd -X - Text from radius.log file Here is my radiusd.conf file. I have included the entire file since I am afraid that if I only include what I deem to be relevant information, I will be leaving out something crucial: -----BEGIN RADIUSD.CONF----- ## ## radiusd.conf -- FreeRADIUS server configuration file. ## ## http://www.freeradius.org/ ## $Id: radiusd.conf.in,v 1.188.2.4 2005/06/11 22:20:40 nbk Exp $ ## # The location of other config files and # logfiles are declared in this file # # Also general configuration for modules can be done # in this file, it is exported through the API to # modules that ask for it. # # The configuration variables defined here are of the form ${foo} # They are local to this file, and do not change from request to # request. # # The per-request variables are of the form %{Attribute-Name}, and # are taken from the values of the attribute in the incoming # request. See 'doc/variables.txt' for more information. prefix = /usr/local exec_prefix = ${prefix} sysconfdir = ${prefix}/etc localstatedir = /var sbindir = ${exec_prefix}/sbin logdir = /var/log raddbdir = ${sysconfdir}/raddb radacctdir = ${logdir}/radacct # Location of config and logfiles. confdir = ${raddbdir} run_dir = ${localstatedir}/run/radiusd # # The logging messages for the server are appended to the # tail of this file. # log_file = ${logdir}/radius.log # # libdir: Where to find the rlm_* modules. # # This should be automatically set at configuration time. # # If the server builds and installs, but fails at execution time # with an 'undefined symbol' error, then you can use the libdir # directive to work around the problem. # # The cause is usually that a library has been installed on your # system in a place where the dynamic linker CANNOT find it. When # executing as root (or another user), your personal environment MAY # be set up to allow the dynamic linker to find the library. When # executing as a daemon, FreeRADIUS MAY NOT have the same # personalized configuration. # # To work around the problem, find out which library contains that symbol, # and add the directory containing that library to the end of 'libdir', # with a colon separating the directory names. NO spaces are allowed. # # e.g. libdir = /usr/local/lib:/opt/package/lib # # You can also try setting the LD_LIBRARY_PATH environment variable # in a script which starts the server. # # If that does not work, then you can re-configure and re-build the # server to NOT use shared libraries, via: # # ./configure --disable-shared # make # make install # libdir = ${exec_prefix}/lib # pidfile: Where to place the PID of the RADIUS server. # # The server may be signalled while it's running by using this # file. # # This file is written when ONLY running in daemon mode. # # e.g.: kill -HUP `cat /var/run/radiusd/radiusd.pid` # pidfile = ${run_dir}/radiusd.pid # user/group: The name (or #number) of the user/group to run radiusd as. # # If these are commented out, the server will run as the user/group # that started it. In order to change to a different user/group, you # MUST be root ( or have root privleges ) to start the server. # # We STRONGLY recommend that you run the server with as few permissions # as possible. That is, if you're not using shadow passwords, the # user and group items below should be set to 'nobody'. # # On SCO (ODT 3) use "user = nouser" and "group = nogroup". # # NOTE that some kernels refuse to setgid(group) when the value of # (unsigned)group is above 60000; don't use group nobody on these systems! # # On systems with shadow passwords, you might have to set 'group = shadow' # for the server to be able to read the shadow password file. If you can # authenticate users while in debug mode, but not in daemon mode, it may be # that the debugging mode server is running as a user that can read the # shadow info, and the user listed below can not. # #user = nobody #group = nobody # max_request_time: The maximum time (in seconds) to handle a request. # # Requests which take more time than this to process may be killed, and # a REJECT message is returned. # # WARNING: If you notice that requests take a long time to be handled, # then this MAY INDICATE a bug in the server, in one of the modules # used to handle a request, OR in your local configuration. # # This problem is most often seen when using an SQL database. If it takes # more than a second or two to receive an answer from the SQL database, # then it probably means that you haven't indexed the database. See your # SQL server documentation for more information. # # Useful range of values: 5 to 120 # max_request_time = 30 # delete_blocked_requests: If the request takes MORE THAN 'max_request_time' # to be handled, then maybe the server should delete it. # # If you're running in threaded, or thread pool mode, this setting # should probably be 'no'. Setting it to 'yes' when using a threaded # server MAY cause the server to crash! # delete_blocked_requests = no # cleanup_delay: The time to wait (in seconds) before cleaning up # a reply which was sent to the NAS. # # The RADIUS request is normally cached internally for a short period # of time, after the reply is sent to the NAS. The reply packet may be # lost in the network, and the NAS will not see it. The NAS will then # re-send the request, and the server will respond quickly with the # cached reply. # # If this value is set too low, then duplicate requests from the NAS # MAY NOT be detected, and will instead be handled as seperate requests. # # If this value is set too high, then the server will cache too many # requests, and some new requests may get blocked. (See 'max_requests'.) # # Useful range of values: 2 to 10 # cleanup_delay = 5 # max_requests: The maximum number of requests which the server keeps # track of. This should be 256 multiplied by the number of clients. # e.g. With 4 clients, this number should be 1024. # # If this number is too low, then when the server becomes busy, # it will not respond to any new requests, until the 'cleanup_delay' # time has passed, and it has removed the old requests. # # If this number is set too high, then the server will use a bit more # memory for no real benefit. # # If you aren't sure what it should be set to, it's better to set it # too high than too low. Setting it to 1000 per client is probably # the highest it should be. # # Useful range of values: 256 to infinity # max_requests = 1024 # bind_address: Make the server listen on a particular IP address, and # send replies out from that address. This directive is most useful # for machines with multiple IP addresses on one interface. # # It can either contain "*", or an IP address, or a fully qualified # Internet domain name. The default is "*" # # As of 1.0, you can also use the "listen" directive. See below for # more information. # bind_address = * # port: Allows you to bind FreeRADIUS to a specific port. # # The default port that most NAS boxes use is 1645, which is historical. # RFC 2138 defines 1812 to be the new port. Many new servers and # NAS boxes use 1812, which can create interoperability problems. # # The port is defined here to be 0 so that the server will pick up # the machine's local configuration for the radius port, as defined # in /etc/services. # # If you want to use the default RADIUS port as defined on your server, # (usually through 'grep radius /etc/services') set this to 0 (zero). # # A port given on the command-line via '-p' over-rides this one. # # As of 1.0, you can also use the "listen" directive. See below for # more information. # port = 0 # # By default, the server uses "bind_address" to listen to all IP's # on a machine, or just one IP. The "port" configuration is used # to select the authentication port used when listening on those # addresses. # # If you want the server to listen on additional addresses, you can # use the "listen" section. A sample section (commented out) is included # below. This "listen" section duplicates the functionality of the # "bind_address" and "port" configuration entries, but it only listens # for authentication packets. # # If you comment out the "bind_address" and "port" configuration entries, # then it becomes possible to make the server accept only accounting, # or authentication packets. Previously, it always listened for both # types of packets, and it was impossible to make it listen for only # one type of packet. # #listen { # IP address on which to listen. # Allowed values are: # dotted quad (1.2.3.4) # hostname (radius.example.com) # wildcard (*) # ipaddr = * # Port on which to listen. # Allowed values are: # integer port number (1812) # 0 means "use /etc/services for the proper port" # port = 0 # Type of packets to listen for. # Allowed values are: # auth listen for authentication packets # acct listen for accounting packets # # type = auth #} # hostname_lookups: Log the names of clients or just their IP addresses # e.g., www.freeradius.org (on) or 206.47.27.232 (off). # # The default is 'off' because it would be overall better for the net # if people had to knowingly turn this feature on, since enabling it # means that each client request will result in AT LEAST one lookup # request to the nameserver. Enabling hostname_lookups will also # mean that your server may stop randomly for 30 seconds from time # to time, if the DNS requests take too long. # # Turning hostname lookups off also means that the server won't block # for 30 seconds, if it sees an IP address which has no name associated # with it. # # allowed values: {no, yes} # hostname_lookups = no # Core dumps are a bad thing. This should only be set to 'yes' # if you're debugging a problem with the server. # # allowed values: {no, yes} # allow_core_dumps = no # Regular expressions # # These items are set at configure time. If they're set to "yes", # then setting them to "no" turns off regular expression support. # # If they're set to "no" at configure time, then setting them to "yes" # WILL NOT WORK. It will give you an error. # regular_expressions = yes extended_expressions = yes # Log the full User-Name attribute, as it was found in the request. # # allowed values: {no, yes} # log_stripped_names = no # Log authentication requests to the log file. # # allowed values: {no, yes} # log_auth = no # Log passwords with the authentication requests. # log_auth_badpass - logs password if it's rejected # log_auth_goodpass - logs password if it's correct # # allowed values: {no, yes} # log_auth_badpass = no log_auth_goodpass = no # usercollide: Turn "username collision" code on and off. See the # "doc/duplicate-users" file # # WARNING # !!!!!!! Setting this to "yes" may result in the server behaving # !!!!!!! strangely. The "username collision" code will ONLY work # !!!!!!! with clear-text passwords. Even then, it may not do what # !!!!!!! you want, or what you expect. # !!!!!!! # !!!!!!! We STRONGLY RECOMMEND that you do not use this feature, # !!!!!!! and that you find another way of acheiving the same goal. # !!!!!!! # !!!!!!! e,g. module fail-over. See 'doc/configurable_failover' # WARNING # usercollide = no # lower_user / lower_pass: # Lower case the username/password "before" or "after" # attempting to authenticate. # # If "before", the server will first modify the request and then try # to auth the user. If "after", the server will first auth using the # values provided by the user. If that fails it will reprocess the # request after modifying it as you specify below. # # This is as close as we can get to case insensitivity. It is the # admin's job to ensure that the username on the auth db side is # *also* lowercase to make this work # # Default is 'no' (don't lowercase values) # Valid values = "before" / "after" / "no" # lower_user = no lower_pass = no # nospace_user / nospace_pass: # # Some users like to enter spaces in their username or password # incorrectly. To save yourself the tech support call, you can # eliminate those spaces here: # # Default is 'no' (don't remove spaces) # Valid values = "before" / "after" / "no" (explanation above) # nospace_user = no nospace_pass = no # The program to execute to do concurrency checks. checkrad = ${sbindir}/checkrad # SECURITY CONFIGURATION # # There may be multiple methods of attacking on the server. This # section holds the configuration items which minimize the impact # of those attacks # security { # # max_attributes: The maximum number of attributes # permitted in a RADIUS packet. Packets which have MORE # than this number of attributes in them will be dropped. # # If this number is set too low, then no RADIUS packets # will be accepted. # # If this number is set too high, then an attacker may be # able to send a small number of packets which will cause # the server to use all available memory on the machine. # # Setting this number to 0 means "allow any number of attributes" max_attributes = 200 # # delayed_reject: When sending an Access-Reject, it can be # delayed for a few seconds. This may help slow down a DoS # attack. It also helps to slow down people trying to brute-force # crack a users password. # # Setting this number to 0 means "send rejects immediately" # # If this number is set higher than 'cleanup_delay', then the # rejects will be sent at 'cleanup_delay' time, when the request # is deleted from the internal cache of requests. # # Useful ranges: 1 to 5 reject_delay = 1 # # status_server: Whether or not the server will respond # to Status-Server requests. # # Normally this should be set to "no", because they're useless. # See: http://www.freeradius.org/rfc/rfc2865.html#Keep-Alives # # However, certain NAS boxes may require them. # # When sent a Status-Server message, the server responds with # an Access-Accept packet, containing a Reply-Message attribute, # which is a string describing how long the server has been # running. # status_server = no } # PROXY CONFIGURATION # # proxy_requests: Turns proxying of RADIUS requests on or off. # # The server has proxying turned on by default. If your system is NOT # set up to proxy requests to another server, then you can turn proxying # off here. This will save a small amount of resources on the server. # # If you have proxying turned off, and your configuration files say # to proxy a request, then an error message will be logged. # # To disable proxying, change the "yes" to "no", and comment the # $INCLUDE line. # # allowed values: {no, yes} # # proxy_requests = yes # $INCLUDE ${confdir}/proxy.conf # CLIENTS CONFIGURATION # # Client configuration is defined in "clients.conf". # # The 'clients.conf' file contains all of the information from the old # 'clients' and 'naslist' configuration files. We recommend that you # do NOT use 'client's or 'naslist', although they are still # supported. # # Anything listed in 'clients.conf' will take precedence over the # information from the old-style configuration files. # $INCLUDE ${confdir}/clients.conf # SNMP CONFIGURATION # # Snmp configuration is only valid if SNMP support was enabled # at compile time. # # To enable SNMP querying of the server, set the value of the # 'snmp' attribute to 'yes' # # snmp = no # $INCLUDE ${confdir}/snmp.conf # THREAD POOL CONFIGURATION # # The thread pool is a long-lived group of threads which # take turns (round-robin) handling any incoming requests. # # You probably want to have a few spare threads around, # so that high-load situations can be handled immediately. If you # don't have any spare threads, then the request handling will # be delayed while a new thread is created, and added to the pool. # # You probably don't want too many spare threads around, # otherwise they'll be sitting there taking up resources, and # not doing anything productive. # # The numbers given below should be adequate for most situations. # thread pool { # Number of servers to start initially --- should be a reasonable # ballpark figure. start_servers = 5 # Limit on the total number of servers running. # # If this limit is ever reached, clients will be LOCKED OUT, so it # should NOT BE SET TOO LOW. It is intended mainly as a brake to # keep a runaway server from taking the system with it as it spirals # down... # # You may find that the server is regularly reaching the # 'max_servers' number of threads, and that increasing # 'max_servers' doesn't seem to make much difference. # # If this is the case, then the problem is MOST LIKELY that # your back-end databases are taking too long to respond, and # are preventing the server from responding in a timely manner. # # The solution is NOT do keep increasing the 'max_servers' # value, but instead to fix the underlying cause of the # problem: slow database, or 'hostname_lookups=yes'. # # For more information, see 'max_request_time', above. # max_servers = 32 # Server-pool size regulation. Rather than making you guess # how many servers you need, FreeRADIUS dynamically adapts to # the load it sees, that is, it tries to maintain enough # servers to handle the current load, plus a few spare # servers to handle transient load spikes. # # It does this by periodically checking how many servers are # waiting for a request. If there are fewer than # min_spare_servers, it creates a new spare. If there are # more than max_spare_servers, some of the spares die off. # The default values are probably OK for most sites. # min_spare_servers = 3 max_spare_servers = 10 # There may be memory leaks or resource allocation problems with # the server. If so, set this value to 300 or so, so that the # resources will be cleaned up periodically. # # This should only be necessary if there are serious bugs in the # server which have not yet been fixed. # # '0' is a special value meaning 'infinity', or 'the servers never # exit' max_requests_per_server = 0 } # MODULE CONFIGURATION # # The names and configuration of each module is located in this section. # # After the modules are defined here, they may be referred to by name, # in other sections of this configuration file. # modules { # # Each module has a configuration as follows: # # name [ instance ] { # config_item = value # ... # } # # The 'name' is used to load the 'rlm_name' library # which implements the functionality of the module. # # The 'instance' is optional. To have two different instances # of a module, it first must be referred to by 'name'. # The different copies of the module are then created by # inventing two 'instance' names, e.g. 'instance1' and 'instance2' # # The instance names can then be used in later configuration # INSTEAD of the original 'name'. See the 'radutmp' configuration # below for an example. # # PAP module to authenticate users based on their stored password # # Supports multiple encryption schemes # clear: Clear text # crypt: Unix crypt # md5: MD5 ecnryption # sha1: SHA1 encryption. # DEFAULT: crypt pap { encryption_scheme = crypt } # CHAP module # # To authenticate requests containing a CHAP-Password attribute. # chap { authtype = CHAP } # Pluggable Authentication Modules # # For Linux, see: # http://www.kernel.org/pub/linux/libs/pam/index.html # # WARNING: On many systems, the system PAM libraries have # memory leaks! We STRONGLY SUGGEST that you do not # use PAM for authentication, due to those memory leaks. # pam { # # The name to use for PAM authentication. # PAM looks in /etc/pam.d/${pam_auth_name} # for it's configuration. See 'redhat/radiusd-pam' # for a sample PAM configuration file. # # Note that any Pam-Auth attribute set in the 'authorize' # section will over-ride this one. # pam_auth = radiusd } # Unix /etc/passwd style authentication # unix { # # Cache /etc/passwd, /etc/shadow, and /etc/group # # The default is to NOT cache them. # # For FreeBSD and NetBSD, you do NOT want to enable # the cache, as it's password lookups are done via a # database, so set this value to 'no'. # # Some systems (e.g. RedHat Linux with pam_pwbd) can # take *seconds* to check a password, when th passwd # file containing 1000's of entries. For those systems, # you should set the cache value to 'yes', and set # the locations of the 'passwd', 'shadow', and 'group' # files, below. # # allowed values: {no, yes} cache = no # Reload the cache every 600 seconds (10mins). 0 to disable. cache_reload = 600 # # Define the locations of the normal passwd, shadow, and # group files. # # 'shadow' is commented out by default, because not all # systems have shadow passwords. # # To force the module to use the system password functions, # instead of reading the files, leave the following entries # commented out. # # This is required for some systems, like FreeBSD, # and Mac OSX. # # passwd = /etc/passwd # shadow = /etc/shadow # group = /etc/group # # The location of the "wtmp" file. # This should be moved to it's own module soon. # # The only use for 'radlast'. If you don't use # 'radlast', then you can comment out this item. # radwtmp = ${logdir}/radwtmp } # Extensible Authentication Protocol # # For all EAP related authentications. # Now in another file, because it is very large. # $INCLUDE ${confdir}/eap.conf # Microsoft CHAP authentication # # This module supports MS-CHAP and MS-CHAPv2 authentication. # It also enforces the SMB-Account-Ctrl attribute. # mschap { # # As of 0.9, the mschap module does NOT support # reading from /etc/smbpasswd. # # If you are using /etc/smbpasswd, see the 'passwd' # module for an example of how to use /etc/smbpasswd # authtype value, if present, will be used # to overwrite (or add) Auth-Type during # authorization. Normally should be MS-CHAP authtype = MS-CHAP # if use_mppe is not set to no mschap will # add MS-CHAP-MPPE-Keys for MS-CHAPv1 and # MS-MPPE-Recv-Key/MS-MPPE-Send-Key for MS-CHAPv2 # #use_mppe = no # if mppe is enabled require_encryption makes # encryption moderate # #require_encryption = yes # require_strong always requires 128 bit key # encryption # #require_strong = yes # Windows sends us a username in the form of # DOMAIN\user, but sends the challenge response # based on only the user portion. This hack # corrects for that incorrect behavior. # #with_ntdomain_hack = no # The module can perform authentication itself, OR # use a Windows Domain Controller. This configuration # directive tells the module to call the ntlm_auth # program, which will do the authentication, and return # the NT-Key. Note that you MUST have "winbindd" and # "nmbd" running on the local machine for ntlm_auth # to work. See the ntlm_auth program documentation # for details. # # Be VERY careful when editing the following line! # #ntlm_auth = "/path/to/ntlm_auth --request-nt-key --username=%{Stripped-User-Name:-%{User-Name:-None}} --challenge=%{mschap:Challenge:-00} --nt-response=%{mschap:NT-Response:-00}" } # Lightweight Directory Access Protocol (LDAP) # # This module definition allows you to use LDAP for # authorization and authentication (Auth-Type := LDAP) # # See doc/rlm_ldap for description of configuration options # and sample authorize{} and authenticate{} blocks ldap { server = "10.1.1.71" identity = "cn=admin,o=radius" password = pass basedn = "o=radius" filter = "(uid=%{Stripped-User-Name:-%{User-Name}})" base_filter = "(objectclass=radiusprofile)" # set this to 'yes' to use TLS encrypted connections # to the LDAP database by using the StartTLS extended # operation. # The StartTLS operation is supposed to be used with normal # ldap connections instead of using ldaps (port 689) connections start_tls = no # tls_cacertfile = /path/to/cacert.pem # tls_cacertdir = /path/to/ca/dir/ # tls_certfile = /path/to/radius.crt # tls_keyfile = /path/to/radius.key # tls_randfile = /path/to/rnd # tls_require_cert = "demand" # default_profile = "cn=radprofile,ou=dialup,o=My Org,c=UA" # profile_attribute = "radiusProfileDn" # access_attr = "dialupAccess" # Mapping of RADIUS dictionary attributes to LDAP # directory attributes. dictionary_mapping = ${raddbdir}/ldap.attrmap ldap_connections_number = 5 # # NOTICE: The password_header directive is NOT case insensitive # # password_header = "{clear}" # # Set: password_attribute = nspmPassword # # to get the user's password from a Novell eDirectory # backend. This will work *only if* freeRADIUS is # configured to build with --with-edir option. # # # The server can usually figure this out on its own, and pull # the correct User-Password or NT-Password from the database. # # Note that NT-Passwords MUST be stored as a 32-digit hex # string, and MUST start off with "0x", such as: # # 0x000102030405060708090a0b0c0d0e0f # # Without the leading "0x", NT-Passwords will not work. # This goes for NT-Passwords stored in SQL, too. # # password_attribute = userPassword # # Un-comment the following to disable Novell eDirectory account # policy check and intruder detection. This will work *only if* # FreeRADIUS is configured to build with --with-edir option. # edir_account_policy_check=yes # # groupname_attribute = cn # groupmembership_filter = "(|(&(objectClass=GroupOfNames)(member=%{Ldap-UserDn}))(&(objectClass=GroupOfUniqueNames)(uniquemember=%{Ldap-UserDn})))" # groupmembership_attribute = radiusGroupName timeout = 4 timelimit = 3 net_timeout = 1 # compare_check_items = yes # do_xlat = yes # access_attr_used_for_allow = yes } # passwd module allows to do authorization via any passwd-like # file and to extract any attributes from these modules # # parameters are: # filename - path to filename # format - format for filename record. This parameters # correlates record in the passwd file and RADIUS # attributes. # # Field marked as '*' is key field. That is, the parameter # with this name from the request is used to search for # the record from passwd file # Attribute marked as '=' is added to reply_itmes instead # of default configure_itmes # Attribute marked as '~' is added to request_items # # Field marked as ',' may contain a comma separated list # of attributes. # authtype - if record found this Auth-Type is used to authenticate # user # hashsize - hashtable size. If 0 or not specified records are not # stored in memory and file is red on every request. # allowmultiplekeys - if few records for every key are allowed # ignorenislike - ignore NIS-related records # delimiter - symbol to use as a field separator in passwd file, # for format ':' symbol is always used. '\0', '\n' are # not allowed # # An example configuration for using /etc/smbpasswd. # #passwd etc_smbpasswd { # filename = /etc/smbpasswd # format = "*User-Name::LM-Password:NT-Password:SMB-Account-CTRL-TEXT::" # authtype = MS-CHAP # hashsize = 100 # ignorenislike = no # allowmultiplekeys = no #} # Similar configuration, for the /etc/group file. Adds a Group-Name # attribute for every group that the user is member of. # #passwd etc_group { # filename = /etc/group # format = "=Group-Name:::*,User-Name" # hashsize = 50 # ignorenislike = yes # allowmultiplekeys = yes # delimiter = ":" #} # Realm module, for proxying. # # You can have multiple instances of the realm module to # support multiple realm syntaxs at the same time. The # search order is defined by the order in the authorize and # preacct sections. # # Four config options: # format - must be 'prefix' or 'suffix' # delimiter - must be a single character # ignore_default - set to 'yes' or 'no' # ignore_null - set to 'yes' or 'no' # # ignore_default and ignore_null can be set to 'yes' to prevent # the module from matching against DEFAULT or NULL realms. This # may be useful if you have have multiple instances of the # realm module. # # They both default to 'no'. # # 'realm/username' # # Using this entry, IPASS users have their realm set to "IPASS". realm IPASS { format = prefix delimiter = "/" ignore_default = no ignore_null = no } # 'username@realm' # realm suffix { format = suffix delimiter = "@" ignore_default = no ignore_null = no } # 'username%realm' # realm realmpercent { format = suffix delimiter = "%" ignore_default = no ignore_null = no } # # 'domain\user' # realm ntdomain { format = prefix delimiter = "\\" ignore_default = no ignore_null = no } # A simple value checking module # # It can be used to check if an attribute value in the request # matches a (possibly multi valued) attribute in the check # items This can be used for example for caller-id # authentication. For the module to run, both the request # attribute and the check items attribute must exist # # i.e. # A user has an ldap entry with 2 radiusCallingStationId # attributes with values "12345678" and "12345679". If we # enable rlm_checkval, then any request which contains a # Calling-Station-Id with one of those two values will be # accepted. Requests with other values for # Calling-Station-Id will be rejected. # # Regular expressions in the check attribute value are allowed # as long as the operator is '=~' # checkval { # The attribute to look for in the request item-name = Calling-Station-Id # The attribute to look for in check items. Can be multi valued check-name = Calling-Station-Id # The data type. Can be # string,integer,ipaddr,date,abinary,octets data-type = string # If set to yes and we dont find the item-name attribute in the # request then we send back a reject # DEFAULT is no #notfound-reject = no } # rewrite arbitrary packets. Useful in accounting and authorization. # # # The module can also use the Rewrite-Rule attribute. If it # is set and matches the name of the module instance, then # that module instance will be the only one which runs. # # Also if new_attribute is set to yes then a new attribute # will be created containing the value replacewith and it # will be added to searchin (packet, reply, proxy, proxy_reply or config). # searchfor,ignore_case and max_matches will be ignored in that case. # # Backreferences are supported: %{0} will contain the string the whole match # and %{1} to %{8} will contain the contents of the 1st to the 8th parentheses # # If max_matches is greater than one the backreferences will correspond to the # first match # #attr_rewrite sanecallerid { # attribute = Called-Station-Id # may be "packet", "reply", "proxy", "proxy_reply" or "config" # searchin = packet # searchfor = "[+ ]" # replacewith = "" # ignore_case = no # new_attribute = no # max_matches = 10 # ## If set to yes then the replace string will be appended to the original string # append = no #} # Preprocess the incoming RADIUS request, before handing it off # to other modules. # # This module processes the 'huntgroups' and 'hints' files. # In addition, it re-writes some weird attributes created # by some NASes, and converts the attributes into a form which # is a little more standard. # preprocess { huntgroups = ${confdir}/huntgroups hints = ${confdir}/hints # This hack changes Ascend's wierd port numberings # to standard 0-??? port numbers so that the "+" works # for IP address assignments. with_ascend_hack = no ascend_channels_per_line = 23 # Windows NT machines often authenticate themselves as # NT_DOMAIN\username # # If this is set to 'yes', then the NT_DOMAIN portion # of the user-name is silently discarded. # # This configuration entry SHOULD NOT be used. # See the "realms" module for a better way to handle # NT domains. with_ntdomain_hack = no # Specialix Jetstream 8500 24 port access server. # # If the user name is 10 characters or longer, a "/" # and the excess characters after the 10th are # appended to the user name. # # If you're not running that NAS, you don't need # this hack. with_specialix_jetstream_hack = no # Cisco (and Quintum in Cisco mode) sends it's VSA attributes # with the attribute name *again* in the string, like: # # H323-Attribute = "h323-attribute=value". # # If this configuration item is set to 'yes', then # the redundant data in the the attribute text is stripped # out. The result is: # # H323-Attribute = "value" # # If you're not running a Cisco or Quintum NAS, you don't # need this hack. with_cisco_vsa_hack = no } # Livingston-style 'users' file # files { usersfile = ${confdir}/users acctusersfile = ${confdir}/acct_users preproxy_usersfile = ${confdir}/preproxy_users # If you want to use the old Cistron 'users' file # with FreeRADIUS, you should change the next line # to 'compat = cistron'. You can the copy your 'users' # file from Cistron. compat = no } # Write a detailed log of all accounting records received. # detail { # Note that we do NOT use NAS-IP-Address here, as # that attribute MAY BE from the originating NAS, and # NOT from the proxy which actually sent us the # request. The Client-IP-Address attribute is ALWAYS # the address of the client which sent us the # request. # # The following line creates a new detail file for # every radius client (by IP address or hostname). # In addition, a new detail file is created every # day, so that the detail file doesn't have to go # through a 'log rotation' # # If your detail files are large, you may also want # to add a ':%H' (see doc/variables.txt) to the end # of it, to create a new detail file every hour, e.g.: # # ..../detail-%Y%m%d:%H # # This will create a new detail file for every hour. # detailfile = ${radacctdir}/%{Client-IP-Address}/detail-%Y%m%d # # The Unix-style permissions on the 'detail' file. # # The detail file often contains secret or private # information about users. So by keeping the file # permissions restrictive, we can prevent unwanted # people from seeing that information. detailperm = 0600 } # # Many people want to log authentication requests. # Rather than modifying the server core to print out more # messages, we can use a different instance of the 'detail' # module, to log the authentication requests to a file. # # You will also need to un-comment the 'auth_log' line # in the 'authorize' section, below. # # detail auth_log { # detailfile = ${radacctdir}/%{Client-IP-Address}/auth-detail-%Y%m%d # # This MUST be 0600, otherwise anyone can read # the users passwords! # detailperm = 0600 # } # # This module logs authentication reply packets sent # to a NAS. Both Access-Accept and Access-Reject packets # are logged. # # You will also need to un-comment the 'reply_log' line # in the 'post-auth' section, below. # # detail reply_log { # detailfile = ${radacctdir}/%{Client-IP-Address}/reply-detail-%Y%m%d # # This MUST be 0600, otherwise anyone can read # the users passwords! # detailperm = 0600 # } # # This module logs packets proxied to a home server. # # You will also need to un-comment the 'pre_proxy_log' line # in the 'pre-proxy' section, below. # # detail pre_proxy_log { # detailfile = ${radacctdir}/%{Client-IP-Address}/pre-proxy-detail-%Y%m%d # # This MUST be 0600, otherwise anyone can read # the users passwords! # detailperm = 0600 # } # # This module logs response packets from a home server. # # You will also need to un-comment the 'post_proxy_log' line # in the 'post-proxy' section, below. # # detail post_proxy_log { # detailfile = ${radacctdir}/%{Client-IP-Address}/post-proxy-detail-%Y%m%d # # This MUST be 0600, otherwise anyone can read # the users passwords! # detailperm = 0600 # } # Create a unique accounting session Id. Many NASes re-use or # repeat values for Acct-Session-Id, causing no end of # confusion. # # This module will add a (probably) unique session id # to an accounting packet based on the attributes listed # below found in the packet. See doc/rlm_acct_unique for # more information. # acct_unique { key = "User-Name, Acct-Session-Id, NAS-IP-Address, Client-IP-Address, NAS-Port" } # Include another file that has the SQL-related configuration. # This is another file only because it tends to be big. # # The following configuration file is for use with MySQL. # # For Postgresql, use: ${confdir}/postgresql.conf # For MS-SQL, use: ${confdir}/mssql.conf # For Oracle, use: ${confdir}/oraclesql.conf # # $INCLUDE ${confdir}/sql.conf # For Cisco VoIP specific accounting with Postgresql, # use: ${confdir}/pgsql-voip.conf # # You will also need the sql schema from: # src/billing/cisco_h323_db_schema-postgres.sql # Note: This config can be use AS WELL AS the standard sql # config if you need SQL based Auth # Write a 'utmp' style file, of which users are currently # logged in, and where they've logged in from. # # This file is used mainly for Simultaneous-Use checking, # and also 'radwho', to see who's currently logged in. # radutmp { # Where the file is stored. It's not a log file, # so it doesn't need rotating. # filename = ${logdir}/radutmp # The field in the packet to key on for the # 'user' name, If you have other fields which you want # to use to key on to control Simultaneous-Use, # then you can use them here. # # Note, however, that the size of the field in the # 'utmp' data structure is small, around 32 # characters, so that will limit the possible choices # of keys. # # You may want instead: %{Stripped-User-Name:-%{User-Name}} username = %{User-Name} # Whether or not we want to treat "user" the same # as "USER", or "User". Some systems have problems # with case sensitivity, so this should be set to # 'no' to enable the comparisons of the key attribute # to be case insensitive. # case_sensitive = yes # Accounting information may be lost, so the user MAY # have logged off of the NAS, but we haven't noticed. # If so, we can verify this information with the NAS, # # If we want to believe the 'utmp' file, then this # configuration entry can be set to 'no'. # check_with_nas = yes # Set the file permissions, as the contents of this file # are usually private. perm = 0600 callerid = "yes" } # "Safe" radutmp - does not contain caller ID, so it can be # world-readable, and radwho can work for normal users, without # exposing any information that isn't already exposed by who(1). # # This is another 'instance' of the radutmp module, but it is given # then name "sradutmp" to identify it later in the "accounting" # section. radutmp sradutmp { filename = ${logdir}/sradutmp perm = 0644 callerid = "no" } # attr_filter - filters the attributes received in replies from # proxied servers, to make sure we send back to our RADIUS client # only allowed attributes. attr_filter { attrsfile = ${confdir}/attrs } # counter module: # This module takes an attribute (count-attribute). # It also takes a key, and creates a counter for each unique # key. The count is incremented when accounting packets are # received by the server. The value of the increment depends # on the attribute type. # If the attribute is Acct-Session-Time or of an integer type we add the # value of the attribute. If it is anything else we increase the # counter by one. # # The 'reset' parameter defines when the counters are all reset to # zero. It can be hourly, daily, weekly, monthly or never. # # hourly: Reset on 00:00 of every hour # daily: Reset on 00:00:00 every day # weekly: Reset on 00:00:00 on sunday # monthly: Reset on 00:00:00 of the first day of each month # # It can also be user defined. It should be of the form: # num[hdwm] where: # h: hours, d: days, w: weeks, m: months # If the letter is ommited days will be assumed. In example: # reset = 10h (reset every 10 hours) # reset = 12 (reset every 12 days) # # # The check-name attribute defines an attribute which will be # registered by the counter module and can be used to set the # maximum allowed value for the counter after which the user # is rejected. # Something like: # # DEFAULT Max-Daily-Session := 36000 # Fall-Through = 1 # # You should add the counter module in the instantiate # section so that it registers check-name before the files # module reads the users file. # # If check-name is set and the user is to be rejected then we # send back a Reply-Message and we log a Failure-Message in # the radius.log # If the count attribute is Acct-Session-Time then on each login # we send back the remaining online time as a Session-Timeout attribute # # The counter-name can also be used instead of using the check-name # like below: # # DEFAULT Daily-Session-Time > 3600, Auth-Type = Reject # Reply-Message = "You've used up more than one hour today" # # The allowed-servicetype attribute can be used to only take # into account specific sessions. For example if a user first # logs in through a login menu and then selects ppp there will # be two sessions. One for Login-User and one for Framed-User # service type. We only need to take into account the second one. # # The module should be added in the instantiate, authorize and # accounting sections. Make sure that in the authorize # section it comes after any module which sets the # 'check-name' attribute. # counter daily { filename = ${raddbdir}/db.daily key = User-Name count-attribute = Acct-Session-Time reset = daily counter-name = Daily-Session-Time check-name = Max-Daily-Session allowed-servicetype = Framed-User cache-size = 5000 } # The "always" module is here for debugging purposes. Each # instance simply returns the same result, always, without # doing anything. always fail { rcode = fail } always reject { rcode = reject } always ok { rcode = ok simulcount = 0 mpp = no } # # The 'expression' module currently has no configuration. # # This module is useful only for 'xlat'. To use it, # put 'exec' into the 'instantiate' section. You can then # do dynamic translation of attributes like: # # Attribute-Name = `%{expr:2 + 3 + %{exec: uid -u}}` # # The value of the attribute will be replaced with the output # of the program which is executed. Due to RADIUS protocol # limitations, any output over 253 bytes will be ignored. expr { } # # The 'digest' module currently has no configuration. # # "Digest" authentication against a Cisco SIP server. # See 'doc/rfc/draft-sterman-aaa-sip-00.txt' for details # on performing digest authentication for Cisco SIP servers. # digest { } # # Execute external programs # # This module is useful only for 'xlat'. To use it, # put 'exec' into the 'instantiate' section. You can then # do dynamic translation of attributes like: # # Attribute-Name = `%{exec:/path/to/program args}` # # The value of the attribute will be replaced with the output # of the program which is executed. Due to RADIUS protocol # limitations, any output over 253 bytes will be ignored. # # The RADIUS attributes from the user request will be placed # into environment variables of the executed program, as # described in 'doc/variables.txt' # exec { wait = yes input_pairs = request } # # This is a more general example of the execute module. # # This one is called "echo". # # Attribute-Name = `%{echo:/path/to/program args}` # # If you wish to execute an external program in more than # one section (e.g. 'authorize', 'pre_proxy', etc), then it # is probably best to define a different instance of the # 'exec' module for every section. # exec echo { # # Wait for the program to finish. # # If we do NOT wait, then the program is "fire and # forget", and any output attributes from it are ignored. # # If we are looking for the program to output # attributes, and want to add those attributes to the # request, then we MUST wait for the program to # finish, and therefore set 'wait=yes' # # allowed values: {no, yes} wait = yes # # The name of the program to execute, and it's # arguments. Dynamic translation is done on this # field, so things like the following example will # work. # program = "/bin/echo %{User-Name}" # # The attributes which are placed into the # environment variables for the program. # # Allowed values are: # # request attributes from the request # config attributes from the configuration items list # reply attributes from the reply # proxy-request attributes from the proxy request # proxy-reply attributes from the proxy reply # # Note that some attributes may not exist at some # stages. e.g. There may be no proxy-reply # attributes if this module is used in the # 'authorize' section. # input_pairs = request # # Where to place the output attributes (if any) from # the executed program. The values allowed, and the # restrictions as to availability, are the same as # for the input_pairs. # output_pairs = reply # # When to execute the program. If the packet # type does NOT match what's listed here, then # the module does NOT execute the program. # # For a list of allowed packet types, see # the 'dictionary' file, and look for VALUEs # of the Packet-Type attribute. # # By default, the module executes on ANY packet. # Un-comment out the following line to tell the # module to execute only if an Access-Accept is # being sent to the NAS. # #packet_type = Access-Accept } # Do server side ip pool management. Should be added in post-auth and # accounting sections. # # The module also requires the existance of the Pool-Name # attribute. That way the administrator can add the Pool-Name # attribute in the user profiles and use different pools # for different users. The Pool-Name attribute is a *check* item not # a reply item. # # Example: # radiusd.conf: ippool students { [...] } # users file : DEFAULT Group == students, Pool-Name := "students" # # ********* IF YOU CHANGE THE RANGE PARAMETERS YOU MUST ********* # ********* THEN ERASE THE DB FILES ********* # ippool main_pool { # range-start,range-stop: The start and end ip # addresses for the ip pool range-start = 192.168.1.1 range-stop = 192.168.3.254 # netmask: The network mask used for the ip's netmask = 255.255.255.0 # cache-size: The gdbm cache size for the db # files. Should be equal to the number of ip's # available in the ip pool cache-size = 800 # session-db: The main db file used to allocate ip's to clients session-db = ${raddbdir}/db.ippool # ip-index: Helper db index file used in multilink ip-index = ${raddbdir}/db.ipindex # override: Will this ippool override a Framed-IP-Address already set override = no # maximum-timeout: If not zero specifies the maximum time in seconds an # entry may be active. Default: 0 maximum-timeout = 0 } # ANSI X9.9 token support. Not included by default. # $INCLUDE ${confdir}/x99.conf } # Instantiation # # This section orders the loading of the modules. Modules # listed here will get loaded BEFORE the later sections like # authorize, authenticate, etc. get examined. # # This section is not strictly needed. When a section like # authorize refers to a module, it's automatically loaded and # initialized. However, some modules may not be listed in any # of the following sections, so they can be listed here. # # Also, listing modules here ensures that you have control over # the order in which they are initalized. If one module needs # something defined by another module, you can list them in order # here, and ensure that the configuration will be OK. # instantiate { # # Allows the execution of external scripts. # The entire command line (and output) must fit into 253 bytes. # # e.g. Framed-Pool = `%{exec:/bin/echo foo}` exec # # The expression module doesn't do authorization, # authentication, or accounting. It only does dynamic # translation, of the form: # # Session-Timeout = `%{expr:2 + 3}` # # So the module needs to be instantiated, but CANNOT be # listed in any other section. See 'doc/rlm_expr' for # more information. # expr # # We add the counter module here so that it registers # the check-name attribute before any module which sets # it # daily } # Authorization. First preprocess (hints and huntgroups files), # then realms, and finally look in the "users" file. # # The order of the realm modules will determine the order that # we try to find a matching realm. # # Make *sure* that 'preprocess' comes before any realm if you # need to setup hints for the remote radius server authorize { # # The preprocess module takes care of sanitizing some bizarre # attributes in the request, and turning them into attributes # which are more standard. # # It takes care of processing the 'raddb/hints' and the # 'raddb/huntgroups' files. # # It also adds the %{Client-IP-Address} attribute to the request. preprocess # # If you want to have a log of authentication requests, # un-comment the following line, and the 'detail auth_log' # section, above. # auth_log # attr_filter # # The chap module will set 'Auth-Type := CHAP' if we are # handling a CHAP request and Auth-Type has not already been set chap # # If the users are logging in with an MS-CHAP-Challenge # attribute for authentication, the mschap module will find # the MS-CHAP-Challenge attribute, and add 'Auth-Type := MS-CHAP' # to the request, which will cause the server to then use # the mschap module for authentication. mschap # # If you have a Cisco SIP server authenticating against # FreeRADIUS, uncomment the following line, and the 'digest' # line in the 'authenticate' section. # digest # # Look for IPASS style 'realm/', and if not found, look for # '@realm', and decide whether or not to proxy, based on # that. # IPASS # # If you are using multiple kinds of realms, you probably # want to set "ignore_null = yes" for all of them. # Otherwise, when the first style of realm doesn't match, # the other styles won't be checked. # suffix # ntdomain # # This module takes care of EAP-MD5, EAP-TLS, and EAP-LEAP # authentication. # # It also sets the EAP-Type attribute in the request # attribute list to the EAP type from the packet. eap # # Read the 'users' file files # # Look in an SQL database. The schema of the database # is meant to mirror the "users" file. # # See "Authorization Queries" in sql.conf # sql # # If you are using /etc/smbpasswd, and are also doing # mschap authentication, the un-comment this line, and # configure the 'etc_smbpasswd' module, above. # etc_smbpasswd # # The ldap module will set Auth-Type to LDAP if it has not # already been set ldap # # Enforce daily limits on time spent logged in. # daily # # Use the checkval module # checkval } # Authentication. # # # This section lists which modules are available for authentication. # Note that it does NOT mean 'try each module in order'. It means # that a module from the 'authorize' section adds a configuration # attribute 'Auth-Type := FOO'. That authentication type is then # used to pick the apropriate module from the list below. # # In general, you SHOULD NOT set the Auth-Type attribute. The server # will figure it out on its own, and will do the right thing. The # most common side effect of erroneously setting the Auth-Type # attribute is that one authentication method will work, but the # others will not. # # The common reasons to set the Auth-Type attribute by hand # is to either forcibly reject the user, or forcibly accept him. # authenticate { # # PAP authentication, when a back-end database listed # in the 'authorize' section supplies a password. The # password can be clear-text, or encrypted. Auth-Type PAP { pap } # # Most people want CHAP authentication # A back-end database listed in the 'authorize' section # MUST supply a CLEAR TEXT password. Encrypted passwords # won't work. Auth-Type CHAP { chap } # # MSCHAP authentication. Auth-Type MS-CHAP { mschap } # # If you have a Cisco SIP server authenticating against # FreeRADIUS, uncomment the following line, and the 'digest' # line in the 'authorize' section. # digest # # Pluggable Authentication Modules. # pam # # See 'man getpwent' for information on how the 'unix' # module checks the users password. Note that packets # containing CHAP-Password attributes CANNOT be authenticated # against /etc/passwd! See the FAQ for details. # unix # Uncomment it if you want to use ldap for authentication # # Note that this means "check plain-text password against # the ldap database", which means that EAP won't work, # as it does not supply a plain-text password. # Auth-Type LDAP { # ldap # } # # Allow EAP authentication. eap } # # Pre-accounting. Decide which accounting type to use. # preacct { preprocess # # Ensure that we have a semi-unique identifier for every # request, and many NAS boxes are broken. acct_unique # # Look for IPASS-style 'realm/', and if not found, look for # '@realm', and decide whether or not to proxy, based on # that. # # Accounting requests are generally proxied to the same # home server as authentication requests. # IPASS suffix # ntdomain # # Read the 'acct_users' file files } # # Accounting. Log the accounting data. # accounting { # # Create a 'detail'ed log of the packets. # Note that accounting requests which are proxied # are also logged in the detail file. detail # daily # Update the wtmp file # # If you don't use "radlast", you can delete this line. unix # # For Simultaneous-Use tracking. # # Due to packet losses in the network, the data here # may be incorrect. There is little we can do about it. radutmp # sradutmp # Return an address to the IP Pool when we see a stop record. # main_pool # # Log traffic to an SQL database. # # See "Accounting queries" in sql.conf # sql # Cisco VoIP specific bulk accounting # pgsql-voip } # Session database, used for checking Simultaneous-Use. Either the radutmp # or rlm_sql module can handle this. # The rlm_sql module is *much* faster session { radutmp # # See "Simultaneous Use Checking Querie" in sql.conf # sql } # Post-Authentication # Once we KNOW that the user has been authenticated, there are # additional steps we can take. post-auth { # Get an address from the IP Pool. # main_pool # # If you want to have a log of authentication replies, # un-comment the following line, and the 'detail reply_log' # section, above. # reply_log # # After authenticating the user, do another SQL qeury. # # See "Authentication Logging Queries" in sql.conf # sql # # Un-comment the following if you have set # 'edir_account_policy_check = yes' in the ldap module sub-section of # the 'modules' section. # ldap # # Access-Reject packets are sent through the REJECT sub-section of the # post-auth section. # Uncomment the following and set the module name to the ldap instance # name if you have set 'edir_account_policy_check = yes' in the ldap # module sub-section of the 'modules' section. # Post-Auth-Type REJECT { ldap } } # # When the server decides to proxy a request to a home server, # the proxied request is first passed through the pre-proxy # stage. This stage can re-write the request, or decide to # cancel the proxy. # # Only a few modules currently have this method. # pre-proxy { # attr_rewrite # Uncomment the following line if you want to change attributes # as defined in the preproxy_users file. # files # If you want to have a log of packets proxied to a home # server, un-comment the following line, and the # 'detail pre_proxy_log' section, above. # pre_proxy_log } # # When the server receives a reply to a request it proxied # to a home server, the request may be massaged here, in the # post-proxy stage. # post-proxy { # If you want to have a log of replies from a home server, # un-comment the following line, and the 'detail post_proxy_log' # section, above. # post_proxy_log # attr_rewrite # Uncomment the following line if you want to filter replies from # remote proxies based on the rules defined in the 'attrs' file. # attr_filter # # If you are proxying LEAP, you MUST configure the EAP # module, and you MUST list it here, in the post-proxy # stage. # # You MUST also use the 'nostrip' option in the 'realm' # configuration. Otherwise, the User-Name attribute # in the proxied request will not match the user name # hidden inside of the EAP packet, and the end server will # reject the EAP request. # eap } -----END RADIUSD.CONF----- Here is the debug info captured when radiusd is started and the radtest command is executed: radius# radtest admin pass localhost 10 testing123 -----BEGIN RADIUSD DEBUG----- radius# /usr/local/sbin/radiusd -X Starting - reading configuration files ... reread_config: reading radiusd.conf Config: including file: /usr/local/etc/raddb/clients.conf Config: including file: /usr/local/etc/raddb/eap.conf main: prefix = "/usr/local" main: localstatedir = "/var" main: logdir = "/var/log" main: libdir = "/usr/local/lib" main: radacctdir = "/var/log/radacct" main: hostname_lookups = no main: max_request_time = 30 main: cleanup_delay = 5 main: max_requests = 1024 main: delete_blocked_requests = 0 main: port = 0 main: allow_core_dumps = no main: log_stripped_names = no main: log_file = "/var/log/radius.log" main: log_auth = no main: log_auth_badpass = no main: log_auth_goodpass = no main: pidfile = "/var/run/radiusd/radiusd.pid" main: user = "(null)" main: group = "(null)" main: usercollide = no main: lower_user = "no" main: lower_pass = "no" main: nospace_user = "no" main: nospace_pass = "no" main: checkrad = "/usr/local/sbin/checkrad" main: proxy_requests = yes security: max_attributes = 200 security: reject_delay = 1 security: status_server = no main: debug_level = 0 read_config_files: reading dictionary read_config_files: reading naslist read_config_files: reading clients read_config_files: reading realms radiusd: entering modules setup Module: Library search path is /usr/local/lib Module: Loaded exec exec: wait = yes exec: program = "(null)" exec: input_pairs = "request" exec: output_pairs = "(null)" exec: packet_type = "(null)" rlm_exec: Wait=yes but no output defined. Did you mean output=none? Module: Instantiated exec (exec) Module: Loaded expr Module: Instantiated expr (expr) Module: Loaded PAP pap: encryption_scheme = "crypt" Module: Instantiated pap (pap) Module: Loaded CHAP Module: Instantiated chap (chap) Module: Loaded MS-CHAP mschap: use_mppe = yes mschap: require_encryption = no mschap: require_strong = no mschap: with_ntdomain_hack = no mschap: passwd = "(null)" mschap: authtype = "MS-CHAP" mschap: ntlm_auth = "(null)" Module: Instantiated mschap (mschap) Module: Loaded System unix: cache = no unix: passwd = "(null)" unix: shadow = "(null)" unix: group = "(null)" unix: radwtmp = "/var/log/radwtmp" unix: usegroup = no unix: cache_reload = 600 Module: Instantiated unix (unix) Module: Loaded eap eap: default_eap_type = "md5" eap: timer_expire = 60 eap: ignore_unknown_eap_types = no eap: cisco_accounting_username_bug = no rlm_eap: Loaded and initialized type md5 rlm_eap: Loaded and initialized type leap gtc: challenge = "Password: " gtc: auth_type = "PAP" rlm_eap: Loaded and initialized type gtc mschapv2: with_ntdomain_hack = no rlm_eap: Loaded and initialized type mschapv2 Module: Instantiated eap (eap) Module: Loaded preprocess preprocess: huntgroups = "/usr/local/etc/raddb/huntgroups" preprocess: hints = "/usr/local/etc/raddb/hints" preprocess: with_ascend_hack = no preprocess: ascend_channels_per_line = 23 preprocess: with_ntdomain_hack = no preprocess: with_specialix_jetstream_hack = no preprocess: with_cisco_vsa_hack = no Module: Instantiated preprocess (preprocess) Module: Loaded realm realm: format = "suffix" realm: delimiter = "@" realm: ignore_default = no realm: ignore_null = no Module: Instantiated realm (suffix) Module: Loaded files files: usersfile = "/usr/local/etc/raddb/users" files: acctusersfile = "/usr/local/etc/raddb/acct_users" files: preproxy_usersfile = "/usr/local/etc/raddb/preproxy_users" files: compat = "no" Module: Instantiated files (files) Module: Loaded LDAP ldap: server = "10.1.1.71" ldap: port = 389 ldap: net_timeout = 1 ldap: timeout = 4 ldap: timelimit = 3 ldap: identity = "cn=admin,o=radius" ldap: tls_mode = no ldap: start_tls = no ldap: tls_cacertfile = "(null)" ldap: tls_cacertdir = "(null)" ldap: tls_certfile = "(null)" ldap: tls_keyfile = "(null)" ldap: tls_randfile = "(null)" ldap: tls_require_cert = "allow" ldap: password = "pass" ldap: basedn = "o=radius" ldap: filter = "(uid=%{Stripped-User-Name:-%{User-Name}})" ldap: base_filter = "(objectclass=radiusprofile)" ldap: default_profile = "(null)" ldap: profile_attribute = "(null)" ldap: password_header = "(null)" ldap: password_attribute = "nspmPassword" ldap: access_attr = "(null)" ldap: groupname_attribute = "cn" ldap: groupmembership_filter = "(|(&(objectClass=GroupOfNames)(member=%{Ldap-UserDn}))(&(objectClass=GroupOfUniqueNames)(uniquemember=%{Ldap-UserDn})))" ldap: groupmembership_attribute = "(null)" ldap: dictionary_mapping = "/usr/local/etc/raddb/ldap.attrmap" ldap: ldap_debug = 0 ldap: ldap_connections_number = 5 ldap: compare_check_items = no ldap: access_attr_used_for_allow = yes ldap: do_xlat = yes ldap: edir_account_policy_check = yes rlm_ldap: Registering ldap_groupcmp for Ldap-Group rlm_ldap: Registering ldap_xlat with xlat_name ldap rlm_ldap: reading ldap<->radius mappings from file /usr/local/etc/raddb/ldap.attrmap rlm_ldap: LDAP radiusCheckItem mapped to RADIUS $GENERIC$ rlm_ldap: LDAP radiusReplyItem mapped to RADIUS $GENERIC$ rlm_ldap: LDAP radiusAuthType mapped to RADIUS Auth-Type rlm_ldap: LDAP radiusSimultaneousUse mapped to RADIUS Simultaneous-Use rlm_ldap: LDAP radiusCalledStationId mapped to RADIUS Called-Station-Id rlm_ldap: LDAP radiusCallingStationId mapped to RADIUS Calling-Station-Id rlm_ldap: LDAP lmPassword mapped to RADIUS LM-Password rlm_ldap: LDAP ntPassword mapped to RADIUS NT-Password rlm_ldap: LDAP acctFlags mapped to RADIUS SMB-Account-CTRL-TEXT rlm_ldap: LDAP radiusExpiration mapped to RADIUS Expiration rlm_ldap: LDAP radiusServiceType mapped to RADIUS Service-Type rlm_ldap: LDAP radiusFramedProtocol mapped to RADIUS Framed-Protocol rlm_ldap: LDAP radiusFramedIPAddress mapped to RADIUS Framed-IP-Address rlm_ldap: LDAP radiusFramedIPNetmask mapped to RADIUS Framed-IP-Netmask rlm_ldap: LDAP radiusFramedRoute mapped to RADIUS Framed-Route rlm_ldap: LDAP radiusFramedRouting mapped to RADIUS Framed-Routing rlm_ldap: LDAP radiusFilterId mapped to RADIUS Filter-Id rlm_ldap: LDAP radiusFramedMTU mapped to RADIUS Framed-MTU rlm_ldap: LDAP radiusFramedCompression mapped to RADIUS Framed-Compression rlm_ldap: LDAP radiusLoginIPHost mapped to RADIUS Login-IP-Host rlm_ldap: LDAP radiusLoginService mapped to RADIUS Login-Service rlm_ldap: LDAP radiusLoginTCPPort mapped to RADIUS Login-TCP-Port rlm_ldap: LDAP radiusCallbackNumber mapped to RADIUS Callback-Number rlm_ldap: LDAP radiusCallbackId mapped to RADIUS Callback-Id rlm_ldap: LDAP radiusFramedIPXNetwork mapped to RADIUS Framed-IPX-Network rlm_ldap: LDAP radiusClass mapped to RADIUS Class rlm_ldap: LDAP radiusSessionTimeout mapped to RADIUS Session-Timeout rlm_ldap: LDAP radiusIdleTimeout mapped to RADIUS Idle-Timeout rlm_ldap: LDAP radiusTerminationAction mapped to RADIUS Termination-Action rlm_ldap: LDAP radiusLoginLATService mapped to RADIUS Login-LAT-Service rlm_ldap: LDAP radiusLoginLATNode mapped to RADIUS Login-LAT-Node rlm_ldap: LDAP radiusLoginLATGroup mapped to RADIUS Login-LAT-Group rlm_ldap: LDAP radiusFramedAppleTalkLink mapped to RADIUS Framed-AppleTalk-Link rlm_ldap: LDAP radiusFramedAppleTalkNetwork mapped to RADIUS Framed-AppleTalk-Network rlm_ldap: LDAP radiusFramedAppleTalkZone mapped to RADIUS Framed-AppleTalk-Zone rlm_ldap: LDAP radiusPortLimit mapped to RADIUS Port-Limit rlm_ldap: LDAP radiusLoginLATPort mapped to RADIUS Login-LAT-Port conns: 0x8085400 Module: Instantiated ldap (ldap) Module: Loaded Acct-Unique-Session-Id acct_unique: key = "User-Name, Acct-Session-Id, NAS-IP-Address, Client-IP-Address, NAS-Port" Module: Instantiated acct_unique (acct_unique) Module: Loaded detail detail: detailfile = "/var/log/radacct/%{Client-IP-Address}/detail-%Y%m%d" detail: detailperm = 384 detail: dirperm = 493 detail: locking = no Module: Instantiated detail (detail) Module: Loaded radutmp radutmp: filename = "/var/log/radutmp" radutmp: username = "%{User-Name}" radutmp: case_sensitive = yes radutmp: check_with_nas = yes radutmp: perm = 384 radutmp: callerid = yes Module: Instantiated radutmp (radutmp) Listening on authentication *:1812 Listening on accounting *:1813 Listening on proxy *:1814 Ready to process requests. rad_recv: Access-Request packet from host 127.0.0.1:2302, id=75, length=57 User-Name = "admin" User-Password = "pass" NAS-IP-Address = 255.255.255.255 NAS-Port = 10 Processing the authorize section of radiusd.conf modcall: entering group authorize for request 0 modcall[authorize]: module "preprocess" returns ok for request 0 modcall[authorize]: module "chap" returns noop for request 0 modcall[authorize]: module "mschap" returns noop for request 0 rlm_realm: No '@' in User-Name = "admin", looking up realm NULL rlm_realm: No such realm "NULL" modcall[authorize]: module "suffix" returns noop for request 0 rlm_eap: No EAP-Message, not doing EAP modcall[authorize]: module "eap" returns noop for request 0 users: Matched entry DEFAULT at line 152 modcall[authorize]: module "files" returns ok for request 0 rlm_ldap: - authorize rlm_ldap: performing user authorization for admin radius_xlat: '(uid=admin)' radius_xlat: 'o=radius' rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: attempting LDAP reconnection rlm_ldap: (re)connect to 10.1.1.71:389, authentication 0 rlm_ldap: bind as cn=admin,o=radius/pass to 10.1.1.71:389 rlm_ldap: waiting for bind result ... rlm_ldap: Bind was successful rlm_ldap: performing search in o=radius, with filter (uid=admin) rlm_ldap: Error reading Universal Password.Return Code = 80 rlm_ldap: looking for check items in directory... rlm_ldap: looking for reply items in directory... rlm_ldap: user admin authorized to use remote access rlm_ldap: ldap_release_conn: Release Id: 0 modcall[authorize]: module "ldap" returns ok for request 0 modcall: group authorize returns ok for request 0 rad_check_password: Found Auth-Type System auth: type "System" Processing the authenticate section of radiusd.conf modcall: entering group authenticate for request 0 modcall[authenticate]: module "unix" returns notfound for request 0 modcall: group authenticate returns notfound for request 0 auth: Failed to validate the user. Processing the post-auth section of radiusd.conf modcall: entering group Post-Auth-Type for request 0 modcall[post-auth]: module "ldap" returns noop for request 0 modcall: group Post-Auth-Type returns noop for request 0 Delaying request 0 for 1 seconds Finished request 0 Going to the next request --- Walking the entire request list --- Waking up in 1 seconds... --- Walking the entire request list --- Waking up in 1 seconds... --- Walking the entire request list --- Sending Access-Reject of id 75 to 127.0.0.1:2302 Waking up in 4 seconds... --- Walking the entire request list --- Cleaning up request 0 ID 75 with timestamp 42d39d5d Nothing to do. Sleeping until we see a request. -----END RADIUSD DEBUG----- The line that I find disturbing is the "error reading Universal Password" line. I assume that I must edit my config in some way so that FreeRADIUS is not attempting to read a Universal Password, or somehow tells NLDAP not to send a Universal Password. And finally, the text from radius.log when radiusd is started without debug mode: -----BEGIN RADIUS.LOG----- Fri Jul 8 09:11:39 2005 : Info: rlm_exec: Wait=yes but no output defined. Did you mean output=none? Fri Jul 8 09:11:39 2005 : Info: Ready to process requests. -----END RADIUS.LOG----- Thanks in advance. Josh

2 1