- Freeradius-Users - lists.freeradius.org

unlang & variable
by petr.linke＠seznam.cz 17 May '18

17 May '18

Hi, I need use the value from soh-server and use this value for condition check in the inner virtual server, but it looks, that the variable filled in the soh-server is only local, and is not possible use the value from this variable in the inner virtual server. simple scenario: SOME_ATTR is defined in dictionary as integer in mods-enabled/eap in peap section is enabled soh-server soh = yes soh_virtual_server = "soh-server" server soh-server { ... if (some condition) { update control { SOME_ATTR := some_value } ... } server inner-server { ... if ( &control:SOME_ATTR == 1 ) { do something } in debug I can see, that in the soh-server is filled the variable SOME_ATTR, but in inner-server, when should be evaluated the condition if ( &control: SOME_ATTR == 1 ), I receive error message "ERROR: Failed retrieving values required to evaluate condition". I tried use outer.control in soh-server, but without success. My question: is possible take value defined in soh-server and use this value for condition in inner-server? Thank for any idea, Petr Linke

4 7

Default mysql schema
by Dom Latter 17 May '18

17 May '18

Just a couple of suggestions (which I understand may have been discussed and dismissed before!): For the default mysql schema, have a UNIQUE constraint / key on username / attribute pairs in the applicable tables - most importantly for us this is radcheck. Have a key on username in radpostauth.

3 5

response sent after do_not_respond called
by Geoffrey D. Bennett 17 May '18

17 May '18

Hi there, I'm having trouble getting the do_not_respond policy working in the post-auth section with FreeRADIUS 3.0.17. I've got a minimal testcase, reproduced with an almost-default 3.0.17 config built from (I only disabled EAP, removed EAP references from sites-enabled/default and enabled test user "bob" in mods-config/files/authorize). I can insert do_not_respond at the top of the authorize or authenticate sections, and I get the expected behaviour (no response sent and "Not responding to request", "Not sending reply to client" messages in the "radiusd -X" output). E.g.: authenticate { Auth-Type PAP { do_not_respond ... If I insert do_not_respond at the top of the post-auth section, then an Access-Accept response is sent. E.g.: post-auth { do_not_respond ... Here are the differences between the "radiusd -X" output working vs. not-working: Working (do_not_respond in authenticate section): (0) Found Auth-Type = PAP (0) # Executing group from file .../freeradius-server-3.0.17/raddb/sites-enabled/default (0) Auth-Type PAP { (0) policy do_not_respond { (0) update control { (0) &Response-Packet-Type := Do-Not-Respond (0) } # update control = noop (0) [handled] = handled (0) } # policy do_not_respond = handled (0) } # Auth-Type PAP = handled (0) Not responding to request (0) # Executing section post-auth from file .../freeradius-server-3.0.17/raddb/sites-enabled/default (0) post-auth { (0) update { (0) No attributes updated (0) } # update = noop (0) [exec] = noop (0) } # post-auth = noop (0) Not sending reply to client. (0) Finished request Not working (do_not_respond in post-auth section): (0) Found Auth-Type = PAP (0) # Executing group from file .../freeradius-server-3.0.17/raddb/sites-enabled/default (0) Auth-Type PAP { (0) pap: Login attempt with password (0) pap: Comparing with "known good" Cleartext-Password (0) pap: User authenticated successfully (0) [pap] = ok (0) } # Auth-Type PAP = ok (0) # Executing section post-auth from file .../freeradius-server-3.0.17/raddb/sites-enabled/default (0) post-auth { (0) policy do_not_respond { (0) update control { (0) &Response-Packet-Type := Do-Not-Respond (0) } # update control = noop (0) [handled] = handled (0) } # policy do_not_respond = handled (0) } # post-auth = handled (0) Sent Access-Accept Id 73 from 127.0.0.1:1812 to 127.0.0.1:59268 length 0 (0) Reply-Message = "Hello, bob" (0) Finished request My ultimate goal is to do this conditionally from rlm_perl, such as described here: http://lists.freeradius.org/pipermail/freeradius-users/2015-September/07960… but when I try that, I see the same results as above, which is how I came up with this minimal test case. Thanks, Geoffrey.

3 8

Machine auth using Samba
by Tornóci László 17 May '18

17 May '18

Hi, I am using FR 3.0.13 for eduroam (setting VLAN dynamically, auth is EAP-TTLS/PAP using LDAP). It works very well. Now I am planning to set up wifi access for a couple of dozens of Win 10 laptops. I would like to achieve the following: - automatic machine auth (no user intervention) - only these machines should be able to access the VLAN that is designated for them If possible, I want to have more security than just checking MAC addresses. I know you can do that with AD, however I don't have that. Is it possible and do you recommend to do this kind of thing using samba? I appreciate if you send me tips or point me to good descriptions. Yours: Laszlo

3 3

DHCP Server Limits
by 8zero2 operations 17 May '18

17 May '18

Hi, I have a setup which has multiple /20s(atleast 6) and i want to manage dhcp using FR 3.0.16. Now As i see I have to enter all the IP address in mysql for the FR to offer IP from when a DHCP request comes in. The total entries amount to 24576 so is it feasible to have frequent dhcp requests coming in, And as i see it searches in table everytime a request is coming. I might even have to throw in another sql query for DHCP request authentication, So is it a scalable solution? Or should i go for ISC(KEA also coming round the corner)? Sorry Its not related to Freeradius, but i wanted an advice from experts. Regards, Anirudh Malhotra Mail: 8zero2.in(a)gmail.com Facebook: www.facebook.com/8zero2 Twitter: @8zero2_in Blog: blog.8zero2.in

2 1

Error while initializing freeradius during instantiate phase for attr_filter
by Saurabh Lahoti 16 May '18

16 May '18

Hi, While initializing freeradius, below error is received during instantiate phase: # Instantiating module "attr_filter.access_reject" from file /usr/app/radius-new2/prod-corp-internal/etc/raddb/mods-enabled/attr_filter reading pairlist file /usr/app/radius-new2/prod-corp-internal/etc/raddb/mods-config/attr_filter/access_reject /usr/app/radius-new2/prod-corp-internal/etc/raddb/mods-config/attr_filter/access_reject[18]: Entry does not begin with a user name Errors reading /usr/app/radius-new2/prod-corp-internal/etc/raddb/mods-config/attr_filter/access_reject /usr/app/radius-new2/prod-corp-internal/etc/raddb/mods-enabled/attr_filter[28]: Instantiation failed for module "attr_filter.access_reject" attr_filter: # attr_filter - filters the attributes received in replies from # proxied servers, to make sure we send back to our RADIUS client # only allowed attributes. attr_filter attr_filter.post-proxy { # key = "%{Realm}" filename = ${modconfdir}/${.:name}/post-proxy } # attr_filter - filters the attributes in the packets we send to # the RADIUS home servers. attr_filter attr_filter.pre-proxy { # key = "%{Realm}" filename = ${modconfdir}/${.:name}/pre-proxy } # Enforce RFC requirements on the contents of Access-Reject # packets. See the comments at the top of the file for # more details. # attr_filter attr_filter.access_reject { key = "%{User-Name}" filename = ${modconfdir}/${.:name}/access_reject } # Enforce RFC requirements on the contents of Access-Challenge # packets. See the comments at the top of the file for # more details. # attr_filter attr_filter.access_challenge { key = "%{User-Name}" filename = ${modconfdir}/${.:name}/access_challenge } # Enforce RFC requirements on the contents of the # Accounting-Response packets. See the comments at the # top of the file for more details. # attr_filter attr_filter.accounting_response { key = "%{User-Name}" filename = ${modconfdir}/${.:name}/accounting_response } Access.reject content: DEFAULT EAP-Message =* ANY, State =* ANY, Message-Authenticator =* ANY, Error-Cause =* ANY, Reply-Message =* ANY # MS-CHAP-Error =* ANY, Proxy-State =* ANY, # FreeRADIUS-Response-Delay =* ANY, # FreeRADIUS-Response-Delay-USec =* ANY Can you please help us in here..? ---- *Thanks & Kind Regards,* Saurabh LAHOTI. *Mob: +32.499.82.37.88* *Ideas enlighten Innovation**!!!* Please consider the environment before printing this mail..!!

2 1

Windows 10 in domain connects but fails to manually reconnect
by Nick Howitt 16 May '18

16 May '18

Hi, I have Windows 10 correctly connecting to my WAP with a domain login, but if I then disconnect the WiFi then reconnect manually it never logs in. I've fixed the CN, SubjectAltName and certificate constraints at it was throwing a warning or error which has now gone. Below is the debug log. Sections (0) to (9) are the successful log in. I then manually disconnected and reconnected which are sections (10) onwards. I've cut the log at (30) but it keeps going. FreeRADIUS Version 3.0.13 Copyright (C) 1999-2017 The FreeRADIUS server project and contributors There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE You may redistribute copies of FreeRADIUS under the terms of the GNU General Public License For more information about these matters, see the file named COPYRIGHT Starting - reading configuration files ... including dictionary file /usr/share/freeradius/dictionary including dictionary file /usr/share/freeradius/dictionary.dhcp including dictionary file /usr/share/freeradius/dictionary.vqp including dictionary file /etc/raddb/dictionary including configuration file /etc/raddb/radiusd.conf including configuration file /etc/raddb/proxy.conf including configuration file /etc/raddb/clearos-proxy.conf including configuration file /etc/raddb/clearos-clients.conf including files in directory /etc/raddb/mods-enabled/ including configuration file /etc/raddb/mods-enabled/linelog including configuration file /etc/raddb/mods-enabled/radutmp including configuration file /etc/raddb/mods-enabled/preprocess including configuration file /etc/raddb/mods-enabled/dynamic_clients including configuration file /etc/raddb/mods-enabled/expr including configuration file /etc/raddb/mods-enabled/realm including configuration file /etc/raddb/mods-enabled/detail including configuration file /etc/raddb/mods-enabled/expiration including configuration file /etc/raddb/mods-enabled/dhcp including configuration file /etc/raddb/mods-enabled/echo including configuration file /etc/raddb/mods-enabled/pap including configuration file /etc/raddb/mods-enabled/sradutmp including configuration file /etc/raddb/mods-enabled/detail.log including configuration file /etc/raddb/mods-enabled/mschap including configuration file /etc/raddb/mods-enabled/logintime including configuration file /etc/raddb/mods-enabled/unpack including configuration file /etc/raddb/mods-enabled/eap including configuration file /etc/raddb/mods-enabled/always including configuration file /etc/raddb/mods-enabled/exec including configuration file /etc/raddb/mods-enabled/cache_eap including configuration file /etc/raddb/mods-enabled/files including configuration file /etc/raddb/mods-enabled/utf8 including configuration file /etc/raddb/mods-enabled/ldap including configuration file /etc/raddb/mods-enabled/passwd including configuration file /etc/raddb/mods-enabled/ntlm_auth including configuration file /etc/raddb/mods-enabled/replicate including configuration file /etc/raddb/mods-enabled/digest including configuration file /etc/raddb/mods-enabled/soh including configuration file /etc/raddb/mods-enabled/date including configuration file /etc/raddb/mods-enabled/attr_filter including configuration file /etc/raddb/mods-enabled/unix including configuration file /etc/raddb/mods-enabled/chap including files in directory /etc/raddb/policy.d/ including configuration file /etc/raddb/policy.d/debug including configuration file /etc/raddb/policy.d/control including configuration file /etc/raddb/policy.d/dhcp including configuration file /etc/raddb/policy.d/filter including configuration file /etc/raddb/policy.d/eap including configuration file /etc/raddb/policy.d/cui including configuration file /etc/raddb/policy.d/operator-name including configuration file /etc/raddb/policy.d/canonicalization including configuration file /etc/raddb/policy.d/accounting including files in directory /etc/raddb/sites-enabled/ including configuration file /etc/raddb/sites-enabled/inner-tunnel including configuration file /etc/raddb/sites-enabled/default main { security { user = "radiusd" group = "radiusd" allow_core_dumps = no } name = "radiusd" prefix = "/usr" localstatedir = "/var" logdir = "/var/log/radius" run_dir = "/var/run/radiusd" } main { name = "radiusd" prefix = "/usr" localstatedir = "/var" sbindir = "/usr/sbin" logdir = "/var/log/radius" run_dir = "/var/run/radiusd" libdir = "/usr/lib64/freeradius" radacctdir = "/var/log/radius/radacct" hostname_lookups = no max_request_time = 30 cleanup_delay = 5 max_requests = 16384 pidfile = "/var/run/radiusd/radiusd.pid" checkrad = "/usr/sbin/checkrad" debug_level = 0 proxy_requests = yes log { stripped_names = no auth = no auth_badpass = no auth_goodpass = no colourise = yes msg_denied = "You are already logged in - access denied" } resources { } security { max_attributes = 200 reject_delay = 1.000000 status_server = yes } } radiusd: #### Loading Realms and Home Servers #### proxy server { retry_delay = 5 retry_count = 3 default_fallback = no dead_time = 120 wake_all_if_all_dead = no } home_server localhost { ipaddr = 127.0.0.1 port = 1812 type = "auth" secret = <<< secret >>> response_window = 20.000000 response_timeouts = 1 max_outstanding = 65536 zombie_period = 40 status_check = "status-server" ping_interval = 30 check_interval = 30 check_timeout = 4 num_answers_to_alive = 3 revive_interval = 120 limit { max_connections = 16 max_requests = 0 lifetime = 0 idle_timeout = 0 } coa { irt = 2 mrt = 16 mrc = 5 mrd = 30 } } home_server_pool my_auth_failover { type = fail-over home_server = localhost } realm example.com { auth_pool = my_auth_failover } realm LOCAL { } realm CLEARSYSTEM { } radiusd: #### Loading Clients #### client 10.0.2.15 { require_message_authenticator = no secret = <<< secret >>> shortname = "eapol_test1" limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } No 'ipaddr' or 'ipv4addr' or 'ipv6addr' field found in client 10.0.2.15. Please fix your configuration Support for old-style clients will be removed in a future release client 172.17.2.5 { require_message_authenticator = no secret = <<< secret >>> shortname = "eapol_test2" limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } No 'ipaddr' or 'ipv4addr' or 'ipv6addr' field found in client 172.17.2.5. Please fix your configuration Support for old-style clients will be removed in a future release client 172.22.22.2 { require_message_authenticator = no secret = <<< secret >>> shortname = "Draytek" limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } No 'ipaddr' or 'ipv4addr' or 'ipv6addr' field found in client 172.22.22.2. Please fix your configuration Support for old-style clients will be removed in a future release client 172.22.22.3 { require_message_authenticator = no secret = <<< secret >>> shortname = "eapol_test" limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } No 'ipaddr' or 'ipv4addr' or 'ipv6addr' field found in client 172.22.22.3. Please fix your configuration Support for old-style clients will be removed in a future release client 172.22.22.254 { require_message_authenticator = no secret = <<< secret >>> shortname = "Tomato" limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } No 'ipaddr' or 'ipv4addr' or 'ipv6addr' field found in client 172.22.22.254. Please fix your configuration Support for old-style clients will be removed in a future release Debugger not attached # Creating Auth-Type = mschap # Creating Auth-Type = eap # Creating Auth-Type = PAP # Creating Auth-Type = CHAP # Creating Auth-Type = MS-CHAP # Creating Auth-Type = digest radiusd: #### Instantiating modules #### modules { # Loaded module rlm_linelog # Loading module "linelog" from file /etc/raddb/mods-enabled/linelog linelog { filename = "/var/log/radius/linelog" escape_filenames = no syslog_severity = "info" permissions = 384 format = "This is a log message for %{User-Name}" reference = "messages.%{%{reply:Packet-Type}:-default}" } # Loading module "log_accounting" from file /etc/raddb/mods-enabled/linelog linelog log_accounting { filename = "/var/log/radius/linelog-accounting" escape_filenames = no syslog_severity = "info" permissions = 384 format = "" reference = "Accounting-Request.%{%{Acct-Status-Type}:-unknown}" } # Loaded module rlm_radutmp # Loading module "radutmp" from file /etc/raddb/mods-enabled/radutmp radutmp { filename = "/var/log/radius/radutmp" username = "%{User-Name}" case_sensitive = yes check_with_nas = yes permissions = 384 caller_id = yes } # Loaded module rlm_preprocess # Loading module "preprocess" from file /etc/raddb/mods-enabled/preprocess preprocess { huntgroups = "/etc/raddb/mods-config/preprocess/huntgroups" hints = "/etc/raddb/mods-config/preprocess/hints" with_ascend_hack = no ascend_channels_per_line = 23 with_ntdomain_hack = no with_specialix_jetstream_hack = no with_cisco_vsa_hack = no with_alvarion_vsa_hack = no } # Loaded module rlm_dynamic_clients # Loading module "dynamic_clients" from file /etc/raddb/mods-enabled/dynamic_clients # Loaded module rlm_expr # Loading module "expr" from file /etc/raddb/mods-enabled/expr expr { safe_characters = "@abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789.-_: /Ã¤Ã©Ã¶Ã¼Ã Ã¢Ã¦Ã§Ã¨Ã©ÃªÃ«Ã®Ã¯Ã´Å“Ã¹Ã»Ã¼aÃ¿Ã„Ã‰Ã–ÃœÃŸÃ€Ã‚Ã†Ã‡ÃˆÃ‰ÃŠÃ‹ÃŽÃÃ”Å’Ã™Ã›ÃœÅ¸" } # Loaded module rlm_realm # Loading module "IPASS" from file /etc/raddb/mods-enabled/realm realm IPASS { format = "prefix" delimiter = "/" ignore_default = no ignore_null = no } # Loading module "suffix" from file /etc/raddb/mods-enabled/realm realm suffix { format = "suffix" delimiter = "@" ignore_default = no ignore_null = no } # Loading module "realmpercent" from file /etc/raddb/mods-enabled/realm realm realmpercent { format = "suffix" delimiter = "%" ignore_default = no ignore_null = no } # Loading module "ntdomain" from file /etc/raddb/mods-enabled/realm realm ntdomain { format = "prefix" delimiter = "\\" ignore_default = no ignore_null = no } # Loaded module rlm_detail # Loading module "detail" from file /etc/raddb/mods-enabled/detail detail { filename = "/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loaded module rlm_expiration # Loading module "expiration" from file /etc/raddb/mods-enabled/expiration # Loaded module rlm_dhcp # Loading module "dhcp" from file /etc/raddb/mods-enabled/dhcp # Loaded module rlm_exec # Loading module "echo" from file /etc/raddb/mods-enabled/echo exec echo { wait = yes program = "/bin/echo %{User-Name}" input_pairs = "request" output_pairs = "reply" shell_escape = yes } # Loaded module rlm_pap # Loading module "pap" from file /etc/raddb/mods-enabled/pap pap { normalise = yes } # Loading module "sradutmp" from file /etc/raddb/mods-enabled/sradutmp radutmp sradutmp { filename = "/var/log/radius/sradutmp" username = "%{User-Name}" case_sensitive = yes check_with_nas = yes permissions = 420 caller_id = no } # Loading module "auth_log" from file /etc/raddb/mods-enabled/detail.log detail auth_log { filename = "/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loading module "reply_log" from file /etc/raddb/mods-enabled/detail.log detail reply_log { filename = "/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/reply-detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loading module "pre_proxy_log" from file /etc/raddb/mods-enabled/detail.log detail pre_proxy_log { filename = "/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/pre-proxy-detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loading module "post_proxy_log" from file /etc/raddb/mods-enabled/detail.log detail post_proxy_log { filename = "/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/post-proxy-detail-%Y%m%d" header = "%t" permissions = 384 locking = no escape_filenames = no log_packet_header = no } # Loaded module rlm_mschap # Loading module "mschap" from file /etc/raddb/mods-enabled/mschap mschap { use_mppe = yes require_encryption = no require_strong = no with_ntdomain_hack = yes ntlm_auth = "/usr/bin/ntlm_auth --request-nt-key --username=%{%{Stripped-User-Name}:-%{%{User-Name}:-None}} --challenge=%{%{mschap:Challenge}:-00} --nt-response=%{%{mschap:NT-Response}:-00}" passchange { } allow_retry = yes winbind_retry_with_normalised_username = no } # Loaded module rlm_logintime # Loading module "logintime" from file /etc/raddb/mods-enabled/logintime logintime { minimum_timeout = 60 } # Loaded module rlm_unpack # Loading module "unpack" from file /etc/raddb/mods-enabled/unpack # Loaded module rlm_eap # Loading module "eap" from file /etc/raddb/mods-enabled/eap eap { default_eap_type = "peap" timer_expire = 60 ignore_unknown_eap_types = no cisco_accounting_username_bug = no max_sessions = 16384 } # Loaded module rlm_always # Loading module "reject" from file /etc/raddb/mods-enabled/always always reject { rcode = "reject" simulcount = 0 mpp = no } # Loading module "fail" from file /etc/raddb/mods-enabled/always always fail { rcode = "fail" simulcount = 0 mpp = no } # Loading module "ok" from file /etc/raddb/mods-enabled/always always ok { rcode = "ok" simulcount = 0 mpp = no } # Loading module "handled" from file /etc/raddb/mods-enabled/always always handled { rcode = "handled" simulcount = 0 mpp = no } # Loading module "invalid" from file /etc/raddb/mods-enabled/always always invalid { rcode = "invalid" simulcount = 0 mpp = no } # Loading module "userlock" from file /etc/raddb/mods-enabled/always always userlock { rcode = "userlock" simulcount = 0 mpp = no } # Loading module "notfound" from file /etc/raddb/mods-enabled/always always notfound { rcode = "notfound" simulcount = 0 mpp = no } # Loading module "noop" from file /etc/raddb/mods-enabled/always always noop { rcode = "noop" simulcount = 0 mpp = no } # Loading module "updated" from file /etc/raddb/mods-enabled/always always updated { rcode = "updated" simulcount = 0 mpp = no } # Loading module "exec" from file /etc/raddb/mods-enabled/exec exec { wait = no input_pairs = "request" shell_escape = yes timeout = 10 } # Loaded module rlm_cache # Loading module "cache_eap" from file /etc/raddb/mods-enabled/cache_eap cache cache_eap { driver = "rlm_cache_rbtree" key = "%{%{control:State}:-%{%{reply:State}:-%{State}}}" ttl = 15 max_entries = 0 epoch = 0 add_stats = no } # Loaded module rlm_files # Loading module "files" from file /etc/raddb/mods-enabled/files files { filename = "/etc/raddb/mods-config/files/authorize" acctusersfile = "/etc/raddb/mods-config/files/accounting" preproxy_usersfile = "/etc/raddb/mods-config/files/pre-proxy" } # Loaded module rlm_utf8 # Loading module "utf8" from file /etc/raddb/mods-enabled/utf8 # Loaded module rlm_ldap # Loading module "ldap" from file /etc/raddb/mods-enabled/ldap ldap { server = "localhost" identity = "cn=manager,ou=Internal,dc=system,dc=lan" password = <<< secret >>> sasl { } user { scope = "sub" access_positive = yes sasl { } } group { filter = "(objectClass=posixGroup)" scope = "sub" name_attribute = "cn" membership_attribute = "memberOf" cacheable_name = no cacheable_dn = no } client { filter = "(objectClass=frClient)" scope = "sub" base_dn = "dc=system,dc=lan" } profile { } options { ldap_debug = 40 chase_referrals = yes rebind = yes net_timeout = 1 res_timeout = 20 srv_timelimit = 20 idle = 60 probes = 3 interval = 3 } tls { start_tls = no } } Creating attribute LDAP-Group # Loaded module rlm_passwd # Loading module "etc_passwd" from file /etc/raddb/mods-enabled/passwd passwd etc_passwd { filename = "/etc/passwd" format = "*User-Name:Crypt-Password:" delimiter = ":" ignore_nislike = no ignore_empty = yes allow_multiple_keys = no hash_size = 100 } # Loading module "ntlm_auth" from file /etc/raddb/mods-enabled/ntlm_auth exec ntlm_auth { wait = yes program = "/path/to/ntlm_auth --request-nt-key --domain=MYDOMAIN --username=%{mschap:User-Name} --password=%{User-Password}" shell_escape = yes } # Loaded module rlm_replicate # Loading module "replicate" from file /etc/raddb/mods-enabled/replicate # Loaded module rlm_digest # Loading module "digest" from file /etc/raddb/mods-enabled/digest # Loaded module rlm_soh # Loading module "soh" from file /etc/raddb/mods-enabled/soh soh { dhcp = yes } # Loaded module rlm_date # Loading module "date" from file /etc/raddb/mods-enabled/date date { format = "%b %e %Y %H:%M:%S %Z" } # Loaded module rlm_attr_filter # Loading module "attr_filter.post-proxy" from file /etc/raddb/mods-enabled/attr_filter attr_filter attr_filter.post-proxy { filename = "/etc/raddb/mods-config/attr_filter/post-proxy" key = "%{Realm}" relaxed = no } # Loading module "attr_filter.pre-proxy" from file /etc/raddb/mods-enabled/attr_filter attr_filter attr_filter.pre-proxy { filename = "/etc/raddb/mods-config/attr_filter/pre-proxy" key = "%{Realm}" relaxed = no } # Loading module "attr_filter.access_reject" from file /etc/raddb/mods-enabled/attr_filter attr_filter attr_filter.access_reject { filename = "/etc/raddb/mods-config/attr_filter/access_reject" key = "%{User-Name}" relaxed = no } # Loading module "attr_filter.access_challenge" from file /etc/raddb/mods-enabled/attr_filter attr_filter attr_filter.access_challenge { filename = "/etc/raddb/mods-config/attr_filter/access_challenge" key = "%{User-Name}" relaxed = no } # Loading module "attr_filter.accounting_response" from file /etc/raddb/mods-enabled/attr_filter attr_filter attr_filter.accounting_response { filename = "/etc/raddb/mods-config/attr_filter/accounting_response" key = "%{User-Name}" relaxed = no } # Loaded module rlm_unix # Loading module "unix" from file /etc/raddb/mods-enabled/unix unix { radwtmp = "/var/log/radius/radwtmp" } Creating attribute Unix-Group # Loaded module rlm_chap # Loading module "chap" from file /etc/raddb/mods-enabled/chap instantiate { } # Instantiating module "linelog" from file /etc/raddb/mods-enabled/linelog # Instantiating module "log_accounting" from file /etc/raddb/mods-enabled/linelog # Instantiating module "preprocess" from file /etc/raddb/mods-enabled/preprocess reading pairlist file /etc/raddb/mods-config/preprocess/huntgroups reading pairlist file /etc/raddb/mods-config/preprocess/hints # Instantiating module "IPASS" from file /etc/raddb/mods-enabled/realm # Instantiating module "suffix" from file /etc/raddb/mods-enabled/realm # Instantiating module "realmpercent" from file /etc/raddb/mods-enabled/realm # Instantiating module "ntdomain" from file /etc/raddb/mods-enabled/realm # Instantiating module "detail" from file /etc/raddb/mods-enabled/detail # Instantiating module "expiration" from file /etc/raddb/mods-enabled/expiration # Instantiating module "pap" from file /etc/raddb/mods-enabled/pap # Instantiating module "auth_log" from file /etc/raddb/mods-enabled/detail.log rlm_detail (auth_log): 'User-Password' suppressed, will not appear in detail output # Instantiating module "reply_log" from file /etc/raddb/mods-enabled/detail.log # Instantiating module "pre_proxy_log" from file /etc/raddb/mods-enabled/detail.log # Instantiating module "post_proxy_log" from file /etc/raddb/mods-enabled/detail.log # Instantiating module "mschap" from file /etc/raddb/mods-enabled/mschap rlm_mschap (mschap): authenticating by calling 'ntlm_auth' # Instantiating module "logintime" from file /etc/raddb/mods-enabled/logintime # Instantiating module "eap" from file /etc/raddb/mods-enabled/eap # Linked to sub-module rlm_eap_md5 # Linked to sub-module rlm_eap_leap # Linked to sub-module rlm_eap_gtc gtc { challenge = "Password: " auth_type = "PAP" } # Linked to sub-module rlm_eap_tls tls { tls = "tls-common" } tls-config tls-common { verify_depth = 0 ca_path = "/etc/raddb/certs" pem_file_type = yes private_key_file = "/etc/raddb/certs/server.pem" certificate_file = "/etc/raddb/certs/server.pem" ca_file = "/etc/raddb/certs/ca.pem" private_key_password = <<< secret >>> dh_file = "/etc/raddb/certs/dh" fragment_size = 1024 include_length = yes auto_chain = yes check_crl = no check_all_crl = no cipher_list = "DEFAULT" cipher_server_preference = no ecdh_curve = "prime256v1" cache { enable = no lifetime = 24 max_entries = 255 } verify { skip_if_ocsp_ok = no } ocsp { enable = no override_cert_url = yes url = "http://127.0.0.1/ocsp/" use_nonce = yes timeout = 0 softfail = no } } # Linked to sub-module rlm_eap_ttls ttls { tls = "tls-common" default_eap_type = "md5" copy_request_to_tunnel = no use_tunneled_reply = no virtual_server = "inner-tunnel" include_length = yes require_client_cert = no } tls: Using cached TLS configuration from previous invocation # Linked to sub-module rlm_eap_peap peap { tls = "tls-common" default_eap_type = "mschapv2" copy_request_to_tunnel = no use_tunneled_reply = no proxy_tunneled_request_as_eap = yes virtual_server = "inner-tunnel" soh = no require_client_cert = no } tls: Using cached TLS configuration from previous invocation # Linked to sub-module rlm_eap_mschapv2 mschapv2 { with_ntdomain_hack = no send_error = no } # Instantiating module "reject" from file /etc/raddb/mods-enabled/always # Instantiating module "fail" from file /etc/raddb/mods-enabled/always # Instantiating module "ok" from file /etc/raddb/mods-enabled/always # Instantiating module "handled" from file /etc/raddb/mods-enabled/always # Instantiating module "invalid" from file /etc/raddb/mods-enabled/always # Instantiating module "userlock" from file /etc/raddb/mods-enabled/always # Instantiating module "notfound" from file /etc/raddb/mods-enabled/always # Instantiating module "noop" from file /etc/raddb/mods-enabled/always # Instantiating module "updated" from file /etc/raddb/mods-enabled/always # Instantiating module "cache_eap" from file /etc/raddb/mods-enabled/cache_eap rlm_cache (cache_eap): Driver rlm_cache_rbtree (module rlm_cache_rbtree) loaded and linked # Instantiating module "files" from file /etc/raddb/mods-enabled/files reading pairlist file /etc/raddb/mods-config/files/authorize reading pairlist file /etc/raddb/clearos-users reading pairlist file /etc/raddb/mods-config/files/accounting reading pairlist file /etc/raddb/mods-config/files/pre-proxy # Instantiating module "ldap" from file /etc/raddb/mods-enabled/ldap rlm_ldap: libldap vendor: OpenLDAP, version: 20444 accounting { reference = "%{tolower:type.%{Acct-Status-Type}}" } post-auth { reference = "." } rlm_ldap (ldap): Initialising connection pool pool { start = 5 min = 4 max = 32 spare = 3 uses = 0 lifetime = 0 cleanup_interval = 30 idle_timeout = 60 retry_delay = 1 spread = no } rlm_ldap (ldap): Opening additional connection (0), 1 of 32 pending slots used rlm_ldap (ldap): Connecting to ldap://localhost:389 rlm_ldap (ldap): Waiting for bind result... rlm_ldap (ldap): Bind successful rlm_ldap (ldap): Opening additional connection (1), 1 of 31 pending slots used rlm_ldap (ldap): Connecting to ldap://localhost:389 rlm_ldap (ldap): Waiting for bind result... rlm_ldap (ldap): Bind successful rlm_ldap (ldap): Opening additional connection (2), 1 of 30 pending slots used rlm_ldap (ldap): Connecting to ldap://localhost:389 rlm_ldap (ldap): Waiting for bind result... rlm_ldap (ldap): Bind successful rlm_ldap (ldap): Opening additional connection (3), 1 of 29 pending slots used rlm_ldap (ldap): Connecting to ldap://localhost:389 rlm_ldap (ldap): Waiting for bind result... rlm_ldap (ldap): Bind successful rlm_ldap (ldap): Opening additional connection (4), 1 of 28 pending slots used rlm_ldap (ldap): Connecting to ldap://localhost:389 rlm_ldap (ldap): Waiting for bind result... rlm_ldap (ldap): Bind successful # Instantiating module "etc_passwd" from file /etc/raddb/mods-enabled/passwd rlm_passwd: nfields: 3 keyfield 0(User-Name) listable: no # Instantiating module "attr_filter.post-proxy" from file /etc/raddb/mods-enabled/attr_filter reading pairlist file /etc/raddb/mods-config/attr_filter/post-proxy # Instantiating module "attr_filter.pre-proxy" from file /etc/raddb/mods-enabled/attr_filter reading pairlist file /etc/raddb/mods-config/attr_filter/pre-proxy # Instantiating module "attr_filter.access_reject" from file /etc/raddb/mods-enabled/attr_filter reading pairlist file /etc/raddb/mods-config/attr_filter/access_reject [/etc/raddb/mods-config/attr_filter/access_reject]:11 Check item "FreeRADIUS-Response-Delay" found in filter list for realm "DEFAULT". [/etc/raddb/mods-config/attr_filter/access_reject]:11 Check item "FreeRADIUS-Response-Delay-USec" found in filter list for realm "DEFAULT". # Instantiating module "attr_filter.access_challenge" from file /etc/raddb/mods-enabled/attr_filter reading pairlist file /etc/raddb/mods-config/attr_filter/access_challenge # Instantiating module "attr_filter.accounting_response" from file /etc/raddb/mods-enabled/attr_filter reading pairlist file /etc/raddb/mods-config/attr_filter/accounting_response } # modules radiusd: #### Loading Virtual Servers #### server { # from file /etc/raddb/radiusd.conf } # server server inner-tunnel { # from file /etc/raddb/sites-enabled/inner-tunnel # Loading authenticate {...} # Loading authorize {...} Ignoring "sql" (see raddb/mods-available/README.rst) # Loading session {...} # Loading post-proxy {...} # Loading post-auth {...} # Skipping contents of 'if' as it is always 'false' -- /etc/raddb/sites-enabled/inner-tunnel:331 } # server inner-tunnel server default { # from file /etc/raddb/sites-enabled/default # Loading authenticate {...} # Loading authorize {...} # Loading preacct {...} # Loading accounting {...} # Loading post-proxy {...} # Loading post-auth {...} } # server default radiusd: #### Opening IP addresses and Ports #### listen { type = "auth" ipaddr = 127.0.0.1 port = 18120 } listen { type = "auth" ipaddr = * port = 0 limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } listen { type = "acct" ipaddr = * port = 0 limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } listen { type = "auth" ipv6addr = :: port = 0 limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } listen { type = "acct" ipv6addr = :: port = 0 limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } Listening on auth address 127.0.0.1 port 18120 bound to server inner-tunnel Listening on auth address * port 1812 bound to server default Listening on acct address * port 1813 bound to server default Listening on auth address :: port 1812 bound to server default Listening on acct address :: port 1813 bound to server default Listening on proxy address * port 57252 Listening on proxy address :: port 47451 Ready to process requests (0) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 147 (0) User-Name = "CLEARSYSTEM\\test1" (0) NAS-IP-Address = 172.22.22.254 (0) Called-Station-Id = "001601dfe596" (0) Calling-Station-Id = "74da38d41a8b" (0) NAS-Identifier = "001601dfe596" (0) NAS-Port = 5 (0) Framed-MTU = 1400 (0) NAS-Port-Type = Wireless-802.11 (0) EAP-Message = 0x0200001601434c45415253595354454d5c7465737431 (0) Message-Authenticator = 0x1d84b5eda6657fc2b0664d6a26fab7c9 (0) # Executing section authorize from file /etc/raddb/sites-enabled/default (0) authorize { (0) policy filter_username { (0) if (&User-Name) { (0) if (&User-Name) -> TRUE (0) if (&User-Name) { (0) if (&User-Name =~ / /) { (0) if (&User-Name =~ / /) -> FALSE (0) if (&User-Name =~ /@[^@]*@/ ) { (0) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (0) if (&User-Name =~ /\.\./ ) { (0) if (&User-Name =~ /\.\./ ) -> FALSE (0) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (0) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (0) if (&User-Name =~ /\.$/) { (0) if (&User-Name =~ /\.$/) -> FALSE (0) if (&User-Name =~ /(a)\./) { (0) if (&User-Name =~ /(a)\./) -> FALSE (0) } # if (&User-Name) = notfound (0) } # policy filter_username = notfound (0) [preprocess] = ok (0) [chap] = noop (0) [mschap] = noop (0) [digest] = noop (0) suffix: Checking for suffix after "@" (0) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (0) suffix: No such realm "NULL" (0) [suffix] = noop (0) ntdomain: Checking for prefix before "\" (0) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (0) ntdomain: Found realm "CLEARSYSTEM" (0) ntdomain: Adding Stripped-User-Name = "test1" (0) ntdomain: Adding Realm = "CLEARSYSTEM" (0) ntdomain: Authentication realm is LOCAL (0) [ntdomain] = ok (0) eap: Peer sent EAP Response (code 2) ID 0 length 22 (0) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize (0) [eap] = ok (0) } # authorize = ok (0) Found Auth-Type = eap (0) # Executing group from file /etc/raddb/sites-enabled/default (0) authenticate { (0) eap: Peer sent packet with method EAP Identity (1) (0) eap: Calling submodule eap_peap to process data (0) eap_peap: Initiating new EAP-TLS session (0) eap_peap: [eaptls start] = request (0) eap: Sending EAP Request (code 1) ID 1 length 6 (0) eap: EAP session adding &reply:State = 0x6d805dd76d814438 (0) [eap] = handled (0) } # authenticate = handled (0) Using Post-Auth-Type Challenge (0) # Executing group from file /etc/raddb/sites-enabled/default (0) Challenge { ... } # empty sub-section is ignored (0) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (0) EAP-Message = 0x010100061920 (0) Message-Authenticator = 0x00000000000000000000000000000000 (0) State = 0x6d805dd76d814438dc40c2ae6afa62ac (0) Finished request Waking up in 4.9 seconds. (0) Cleaning up request packet ID 0 with timestamp +13 (1) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 309 (1) User-Name = "CLEARSYSTEM\\test1" (1) NAS-IP-Address = 172.22.22.254 (1) Called-Station-Id = "001601dfe596" (1) Calling-Station-Id = "74da38d41a8b" (1) NAS-Identifier = "001601dfe596" (1) NAS-Port = 5 (1) Framed-MTU = 1400 (1) State = 0x6d805dd76d814438dc40c2ae6afa62ac (1) NAS-Port-Type = Wireless-802.11 (1) EAP-Message = 0x020100a619800000009c16030300970100009303035af2cd197aa9b2ed29f9de90733a7f3238b0584cd2319b55c1e84641e62ee34f00002ac02cc02bc030c02f009f009ec024c023c028c027c00ac009c014c013009d009c003d003c0035002f000a01000040000500050100000000000a00080006001d (1) Message-Authenticator = 0x7fb87a121953bf0a44ec6a8e8af28586 (1) session-state: No cached attributes (1) # Executing section authorize from file /etc/raddb/sites-enabled/default (1) authorize { (1) policy filter_username { (1) if (&User-Name) { (1) if (&User-Name) -> TRUE (1) if (&User-Name) { (1) if (&User-Name =~ / /) { (1) if (&User-Name =~ / /) -> FALSE (1) if (&User-Name =~ /@[^@]*@/ ) { (1) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (1) if (&User-Name =~ /\.\./ ) { (1) if (&User-Name =~ /\.\./ ) -> FALSE (1) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (1) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (1) if (&User-Name =~ /\.$/) { (1) if (&User-Name =~ /\.$/) -> FALSE (1) if (&User-Name =~ /(a)\./) { (1) if (&User-Name =~ /(a)\./) -> FALSE (1) } # if (&User-Name) = notfound (1) } # policy filter_username = notfound (1) [preprocess] = ok (1) [chap] = noop (1) [mschap] = noop (1) [digest] = noop (1) suffix: Checking for suffix after "@" (1) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (1) suffix: No such realm "NULL" (1) [suffix] = noop (1) ntdomain: Checking for prefix before "\" (1) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (1) ntdomain: Found realm "CLEARSYSTEM" (1) ntdomain: Adding Stripped-User-Name = "test1" (1) ntdomain: Adding Realm = "CLEARSYSTEM" (1) ntdomain: Authentication realm is LOCAL (1) [ntdomain] = ok (1) eap: Peer sent EAP Response (code 2) ID 1 length 166 (1) eap: Continuing tunnel setup (1) [eap] = ok (1) } # authorize = ok (1) Found Auth-Type = eap (1) # Executing group from file /etc/raddb/sites-enabled/default (1) authenticate { (1) eap: Expiring EAP session with state 0x6d805dd76d814438 (1) eap: Finished EAP session with state 0x6d805dd76d814438 (1) eap: Previous EAP request found for state 0x6d805dd76d814438, released from the list (1) eap: Peer sent packet with method EAP PEAP (25) (1) eap: Calling submodule eap_peap to process data (1) eap_peap: Continuing EAP-TLS (1) eap_peap: Peer indicated complete TLS record size will be 156 bytes (1) eap_peap: Got complete TLS record (156 bytes) (1) eap_peap: [eaptls verify] = length included (1) eap_peap: (other): before/accept initialization (1) eap_peap: TLS_accept: before/accept initialization (1) eap_peap: <<< recv TLS 1.2 [length 0097] (1) eap_peap: TLS_accept: SSLv3 read client hello A (1) eap_peap: >>> send TLS 1.2 [length 0039] (1) eap_peap: TLS_accept: SSLv3 write server hello A (1) eap_peap: >>> send TLS 1.2 [length 08bd] (1) eap_peap: TLS_accept: SSLv3 write certificate A (1) eap_peap: >>> send TLS 1.2 [length 014d] (1) eap_peap: TLS_accept: SSLv3 write key exchange A (1) eap_peap: >>> send TLS 1.2 [length 0004] (1) eap_peap: TLS_accept: SSLv3 write server done A (1) eap_peap: TLS_accept: SSLv3 flush data (1) eap_peap: TLS_accept: SSLv3 read client certificate A (1) eap_peap: TLS_accept: Need to read more data: SSLv3 read client key exchange A (1) eap_peap: TLS_accept: Need to read more data: SSLv3 read client key exchange A (1) eap_peap: In SSL Handshake Phase (1) eap_peap: In SSL Accept mode (1) eap_peap: [eaptls process] = handled (1) eap: Sending EAP Request (code 1) ID 2 length 1004 (1) eap: EAP session adding &reply:State = 0x6d805dd76c824438 (1) [eap] = handled (1) } # authenticate = handled (1) Using Post-Auth-Type Challenge (1) # Executing group from file /etc/raddb/sites-enabled/default (1) Challenge { ... } # empty sub-section is ignored (1) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (1) EAP-Message = 0x010203ec19c000000a5b160303003902000035030316a54dc3118ee9fa4b5f98e46a2b32d5ddecf2a97c4f67ea076f396d6ac2104e00c03000000dff01000100000b00040300010216030308bd0b0008b90008b60003fb308203f7308202dfa003020102020101300d06092a864886f70d01010b050030 (1) Message-Authenticator = 0x00000000000000000000000000000000 (1) State = 0x6d805dd76c824438dc40c2ae6afa62ac (1) Finished request Waking up in 4.9 seconds. (1) Cleaning up request packet ID 0 with timestamp +13 (2) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 149 (2) User-Name = "CLEARSYSTEM\\test1" (2) NAS-IP-Address = 172.22.22.254 (2) Called-Station-Id = "001601dfe596" (2) Calling-Station-Id = "74da38d41a8b" (2) NAS-Identifier = "001601dfe596" (2) NAS-Port = 5 (2) Framed-MTU = 1400 (2) State = 0x6d805dd76c824438dc40c2ae6afa62ac (2) NAS-Port-Type = Wireless-802.11 (2) EAP-Message = 0x020200061900 (2) Message-Authenticator = 0x8c79c6a2fb19c89ac4017cfaee83ebeb (2) session-state: No cached attributes (2) # Executing section authorize from file /etc/raddb/sites-enabled/default (2) authorize { (2) policy filter_username { (2) if (&User-Name) { (2) if (&User-Name) -> TRUE (2) if (&User-Name) { (2) if (&User-Name =~ / /) { (2) if (&User-Name =~ / /) -> FALSE (2) if (&User-Name =~ /@[^@]*@/ ) { (2) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (2) if (&User-Name =~ /\.\./ ) { (2) if (&User-Name =~ /\.\./ ) -> FALSE (2) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (2) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (2) if (&User-Name =~ /\.$/) { (2) if (&User-Name =~ /\.$/) -> FALSE (2) if (&User-Name =~ /(a)\./) { (2) if (&User-Name =~ /(a)\./) -> FALSE (2) } # if (&User-Name) = notfound (2) } # policy filter_username = notfound (2) [preprocess] = ok (2) [chap] = noop (2) [mschap] = noop (2) [digest] = noop (2) suffix: Checking for suffix after "@" (2) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (2) suffix: No such realm "NULL" (2) [suffix] = noop (2) ntdomain: Checking for prefix before "\" (2) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (2) ntdomain: Found realm "CLEARSYSTEM" (2) ntdomain: Adding Stripped-User-Name = "test1" (2) ntdomain: Adding Realm = "CLEARSYSTEM" (2) ntdomain: Authentication realm is LOCAL (2) [ntdomain] = ok (2) eap: Peer sent EAP Response (code 2) ID 2 length 6 (2) eap: Continuing tunnel setup (2) [eap] = ok (2) } # authorize = ok (2) Found Auth-Type = eap (2) # Executing group from file /etc/raddb/sites-enabled/default (2) authenticate { (2) eap: Expiring EAP session with state 0x6d805dd76c824438 (2) eap: Finished EAP session with state 0x6d805dd76c824438 (2) eap: Previous EAP request found for state 0x6d805dd76c824438, released from the list (2) eap: Peer sent packet with method EAP PEAP (25) (2) eap: Calling submodule eap_peap to process data (2) eap_peap: Continuing EAP-TLS (2) eap_peap: Peer ACKed our handshake fragment (2) eap_peap: [eaptls verify] = request (2) eap_peap: [eaptls process] = handled (2) eap: Sending EAP Request (code 1) ID 3 length 1000 (2) eap: EAP session adding &reply:State = 0x6d805dd76f834438 (2) [eap] = handled (2) } # authenticate = handled (2) Using Post-Auth-Type Challenge (2) # Executing group from file /etc/raddb/sites-enabled/default (2) Challenge { ... } # empty sub-section is ignored (2) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (2) EAP-Message = 0x010303e819408444f5b804aa2d65ef2b23820bb1bf1bfcb24df6bd03eabe61d7bb630cfd9fd6165d19f24d23925593c04c7ec13d5afe51369fe487605e2de3073d043a15e72448712bca946e329e81ff36cebcdfe8be08dc6490da38ed9147e7eac88af7f25487bee0ef80700004b5308204b130820399 (2) Message-Authenticator = 0x00000000000000000000000000000000 (2) State = 0x6d805dd76f834438dc40c2ae6afa62ac (2) Finished request Waking up in 4.9 seconds. (2) Cleaning up request packet ID 0 with timestamp +13 (3) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 149 (3) User-Name = "CLEARSYSTEM\\test1" (3) NAS-IP-Address = 172.22.22.254 (3) Called-Station-Id = "001601dfe596" (3) Calling-Station-Id = "74da38d41a8b" (3) NAS-Identifier = "001601dfe596" (3) NAS-Port = 5 (3) Framed-MTU = 1400 (3) State = 0x6d805dd76f834438dc40c2ae6afa62ac (3) NAS-Port-Type = Wireless-802.11 (3) EAP-Message = 0x020300061900 (3) Message-Authenticator = 0x35a39e6139230d22912378e6c8a35696 (3) session-state: No cached attributes (3) # Executing section authorize from file /etc/raddb/sites-enabled/default (3) authorize { (3) policy filter_username { (3) if (&User-Name) { (3) if (&User-Name) -> TRUE (3) if (&User-Name) { (3) if (&User-Name =~ / /) { (3) if (&User-Name =~ / /) -> FALSE (3) if (&User-Name =~ /@[^@]*@/ ) { (3) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (3) if (&User-Name =~ /\.\./ ) { (3) if (&User-Name =~ /\.\./ ) -> FALSE (3) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (3) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (3) if (&User-Name =~ /\.$/) { (3) if (&User-Name =~ /\.$/) -> FALSE (3) if (&User-Name =~ /(a)\./) { (3) if (&User-Name =~ /(a)\./) -> FALSE (3) } # if (&User-Name) = notfound (3) } # policy filter_username = notfound (3) [preprocess] = ok (3) [chap] = noop (3) [mschap] = noop (3) [digest] = noop (3) suffix: Checking for suffix after "@" (3) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (3) suffix: No such realm "NULL" (3) [suffix] = noop (3) ntdomain: Checking for prefix before "\" (3) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (3) ntdomain: Found realm "CLEARSYSTEM" (3) ntdomain: Adding Stripped-User-Name = "test1" (3) ntdomain: Adding Realm = "CLEARSYSTEM" (3) ntdomain: Authentication realm is LOCAL (3) [ntdomain] = ok (3) eap: Peer sent EAP Response (code 2) ID 3 length 6 (3) eap: Continuing tunnel setup (3) [eap] = ok (3) } # authorize = ok (3) Found Auth-Type = eap (3) # Executing group from file /etc/raddb/sites-enabled/default (3) authenticate { (3) eap: Expiring EAP session with state 0x6d805dd76f834438 (3) eap: Finished EAP session with state 0x6d805dd76f834438 (3) eap: Previous EAP request found for state 0x6d805dd76f834438, released from the list (3) eap: Peer sent packet with method EAP PEAP (25) (3) eap: Calling submodule eap_peap to process data (3) eap_peap: Continuing EAP-TLS (3) eap_peap: Peer ACKed our handshake fragment (3) eap_peap: [eaptls verify] = request (3) eap_peap: [eaptls process] = handled (3) eap: Sending EAP Request (code 1) ID 4 length 669 (3) eap: EAP session adding &reply:State = 0x6d805dd76e844438 (3) [eap] = handled (3) } # authenticate = handled (3) Using Post-Auth-Type Challenge (3) # Executing group from file /etc/raddb/sites-enabled/default (3) Challenge { ... } # empty sub-section is ignored (3) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (3) EAP-Message = 0x0104029d1900278625687474703a2f2f7777772e6578616d706c652e6f72672f6578616d706c655f63612e63726c300d06092a864886f70d01010b050003820101000132a42023b4da19cd0464809979cba06e09409f4cbae9db226b41b48d0c97de8fa6092c00476cb9f16399e310996fb68c40e69b10 (3) Message-Authenticator = 0x00000000000000000000000000000000 (3) State = 0x6d805dd76e844438dc40c2ae6afa62ac (3) Finished request Waking up in 4.9 seconds. (3) Cleaning up request packet ID 0 with timestamp +13 (4) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 279 (4) User-Name = "CLEARSYSTEM\\test1" (4) NAS-IP-Address = 172.22.22.254 (4) Called-Station-Id = "001601dfe596" (4) Calling-Station-Id = "74da38d41a8b" (4) NAS-Identifier = "001601dfe596" (4) NAS-Port = 5 (4) Framed-MTU = 1400 (4) State = 0x6d805dd76e844438dc40c2ae6afa62ac (4) NAS-Port-Type = Wireless-802.11 (4) EAP-Message = 0x0204008819800000007e1603030046100000424104f977f1abd9c3d74a88eac2ee83ee009474c95ec8e0d265416e7b88ea8c1109e7dc7c9d422d8eb0044f2dc31855ba3ddfd3bd4223dd12685b4b6388c6e83be67c14030300010116030300280000000000000000c9cdd6db357f227df3eaa98933ecdb (4) Message-Authenticator = 0xefd856add429620c23bf7cba64530c9e (4) session-state: No cached attributes (4) # Executing section authorize from file /etc/raddb/sites-enabled/default (4) authorize { (4) policy filter_username { (4) if (&User-Name) { (4) if (&User-Name) -> TRUE (4) if (&User-Name) { (4) if (&User-Name =~ / /) { (4) if (&User-Name =~ / /) -> FALSE (4) if (&User-Name =~ /@[^@]*@/ ) { (4) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (4) if (&User-Name =~ /\.\./ ) { (4) if (&User-Name =~ /\.\./ ) -> FALSE (4) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (4) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (4) if (&User-Name =~ /\.$/) { (4) if (&User-Name =~ /\.$/) -> FALSE (4) if (&User-Name =~ /(a)\./) { (4) if (&User-Name =~ /(a)\./) -> FALSE (4) } # if (&User-Name) = notfound (4) } # policy filter_username = notfound (4) [preprocess] = ok (4) [chap] = noop (4) [mschap] = noop (4) [digest] = noop (4) suffix: Checking for suffix after "@" (4) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (4) suffix: No such realm "NULL" (4) [suffix] = noop (4) ntdomain: Checking for prefix before "\" (4) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (4) ntdomain: Found realm "CLEARSYSTEM" (4) ntdomain: Adding Stripped-User-Name = "test1" (4) ntdomain: Adding Realm = "CLEARSYSTEM" (4) ntdomain: Authentication realm is LOCAL (4) [ntdomain] = ok (4) eap: Peer sent EAP Response (code 2) ID 4 length 136 (4) eap: Continuing tunnel setup (4) [eap] = ok (4) } # authorize = ok (4) Found Auth-Type = eap (4) # Executing group from file /etc/raddb/sites-enabled/default (4) authenticate { (4) eap: Expiring EAP session with state 0x6d805dd76e844438 (4) eap: Finished EAP session with state 0x6d805dd76e844438 (4) eap: Previous EAP request found for state 0x6d805dd76e844438, released from the list (4) eap: Peer sent packet with method EAP PEAP (25) (4) eap: Calling submodule eap_peap to process data (4) eap_peap: Continuing EAP-TLS (4) eap_peap: Peer indicated complete TLS record size will be 126 bytes (4) eap_peap: Got complete TLS record (126 bytes) (4) eap_peap: [eaptls verify] = length included (4) eap_peap: <<< recv TLS 1.2 [length 0046] (4) eap_peap: TLS_accept: SSLv3 read client key exchange A (4) eap_peap: TLS_accept: SSLv3 read certificate verify A (4) eap_peap: <<< recv TLS 1.2 [length 0001] (4) eap_peap: <<< recv TLS 1.2 [length 0010] (4) eap_peap: TLS_accept: SSLv3 read finished A (4) eap_peap: >>> send TLS 1.2 [length 0001] (4) eap_peap: TLS_accept: SSLv3 write change cipher spec A (4) eap_peap: >>> send TLS 1.2 [length 0010] (4) eap_peap: TLS_accept: SSLv3 write finished A (4) eap_peap: TLS_accept: SSLv3 flush data (4) eap_peap: (other): SSL negotiation finished successfully (4) eap_peap: SSL Connection Established (4) eap_peap: [eaptls process] = handled (4) eap: Sending EAP Request (code 1) ID 5 length 57 (4) eap: EAP session adding &reply:State = 0x6d805dd769854438 (4) [eap] = handled (4) } # authenticate = handled (4) Using Post-Auth-Type Challenge (4) # Executing group from file /etc/raddb/sites-enabled/default (4) Challenge { ... } # empty sub-section is ignored (4) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (4) EAP-Message = 0x0105003919001403030001011603030028dc5fcf74a4d4eceeb580ed30367b623e9b143f2e07946b341b187a4b5ffedaff73403f3ee546b992 (4) Message-Authenticator = 0x00000000000000000000000000000000 (4) State = 0x6d805dd769854438dc40c2ae6afa62ac (4) Finished request Waking up in 4.9 seconds. (4) Cleaning up request packet ID 0 with timestamp +13 (5) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 149 (5) User-Name = "CLEARSYSTEM\\test1" (5) NAS-IP-Address = 172.22.22.254 (5) Called-Station-Id = "001601dfe596" (5) Calling-Station-Id = "74da38d41a8b" (5) NAS-Identifier = "001601dfe596" (5) NAS-Port = 5 (5) Framed-MTU = 1400 (5) State = 0x6d805dd769854438dc40c2ae6afa62ac (5) NAS-Port-Type = Wireless-802.11 (5) EAP-Message = 0x020500061900 (5) Message-Authenticator = 0x44670280e3acbc66b6f39801f08a9398 (5) session-state: No cached attributes (5) # Executing section authorize from file /etc/raddb/sites-enabled/default (5) authorize { (5) policy filter_username { (5) if (&User-Name) { (5) if (&User-Name) -> TRUE (5) if (&User-Name) { (5) if (&User-Name =~ / /) { (5) if (&User-Name =~ / /) -> FALSE (5) if (&User-Name =~ /@[^@]*@/ ) { (5) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (5) if (&User-Name =~ /\.\./ ) { (5) if (&User-Name =~ /\.\./ ) -> FALSE (5) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (5) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (5) if (&User-Name =~ /\.$/) { (5) if (&User-Name =~ /\.$/) -> FALSE (5) if (&User-Name =~ /(a)\./) { (5) if (&User-Name =~ /(a)\./) -> FALSE (5) } # if (&User-Name) = notfound (5) } # policy filter_username = notfound (5) [preprocess] = ok (5) [chap] = noop (5) [mschap] = noop (5) [digest] = noop (5) suffix: Checking for suffix after "@" (5) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (5) suffix: No such realm "NULL" (5) [suffix] = noop (5) ntdomain: Checking for prefix before "\" (5) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (5) ntdomain: Found realm "CLEARSYSTEM" (5) ntdomain: Adding Stripped-User-Name = "test1" (5) ntdomain: Adding Realm = "CLEARSYSTEM" (5) ntdomain: Authentication realm is LOCAL (5) [ntdomain] = ok (5) eap: Peer sent EAP Response (code 2) ID 5 length 6 (5) eap: Continuing tunnel setup (5) [eap] = ok (5) } # authorize = ok (5) Found Auth-Type = eap (5) # Executing group from file /etc/raddb/sites-enabled/default (5) authenticate { (5) eap: Expiring EAP session with state 0x6d805dd769854438 (5) eap: Finished EAP session with state 0x6d805dd769854438 (5) eap: Previous EAP request found for state 0x6d805dd769854438, released from the list (5) eap: Peer sent packet with method EAP PEAP (25) (5) eap: Calling submodule eap_peap to process data (5) eap_peap: Continuing EAP-TLS (5) eap_peap: Peer ACKed our handshake fragment. handshake is finished (5) eap_peap: [eaptls verify] = success (5) eap_peap: [eaptls process] = success (5) eap_peap: Session established. Decoding tunneled attributes (5) eap_peap: PEAP state TUNNEL ESTABLISHED (5) eap: Sending EAP Request (code 1) ID 6 length 40 (5) eap: EAP session adding &reply:State = 0x6d805dd768864438 (5) [eap] = handled (5) } # authenticate = handled (5) Using Post-Auth-Type Challenge (5) # Executing group from file /etc/raddb/sites-enabled/default (5) Challenge { ... } # empty sub-section is ignored (5) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (5) EAP-Message = 0x010600281900170303001ddc5fcf74a4d4eceff440279910950fcf0da56053dafc7b1a9acc0e9818 (5) Message-Authenticator = 0x00000000000000000000000000000000 (5) State = 0x6d805dd768864438dc40c2ae6afa62ac (5) Finished request Waking up in 4.9 seconds. (5) Cleaning up request packet ID 0 with timestamp +13 (6) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 196 (6) User-Name = "CLEARSYSTEM\\test1" (6) NAS-IP-Address = 172.22.22.254 (6) Called-Station-Id = "001601dfe596" (6) Calling-Station-Id = "74da38d41a8b" (6) NAS-Identifier = "001601dfe596" (6) NAS-Port = 5 (6) Framed-MTU = 1400 (6) State = 0x6d805dd768864438dc40c2ae6afa62ac (6) NAS-Port-Type = Wireless-802.11 (6) EAP-Message = 0x020600351900170303002a0000000000000001dd244541a65b0c86c71280b371970a1a1c7be8090c517215185792c4ef34ace82894 (6) Message-Authenticator = 0xe01b3ffbd597dcf5f7f0f0dd8bc4ea9d (6) session-state: No cached attributes (6) # Executing section authorize from file /etc/raddb/sites-enabled/default (6) authorize { (6) policy filter_username { (6) if (&User-Name) { (6) if (&User-Name) -> TRUE (6) if (&User-Name) { (6) if (&User-Name =~ / /) { (6) if (&User-Name =~ / /) -> FALSE (6) if (&User-Name =~ /@[^@]*@/ ) { (6) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (6) if (&User-Name =~ /\.\./ ) { (6) if (&User-Name =~ /\.\./ ) -> FALSE (6) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (6) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (6) if (&User-Name =~ /\.$/) { (6) if (&User-Name =~ /\.$/) -> FALSE (6) if (&User-Name =~ /(a)\./) { (6) if (&User-Name =~ /(a)\./) -> FALSE (6) } # if (&User-Name) = notfound (6) } # policy filter_username = notfound (6) [preprocess] = ok (6) [chap] = noop (6) [mschap] = noop (6) [digest] = noop (6) suffix: Checking for suffix after "@" (6) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (6) suffix: No such realm "NULL" (6) [suffix] = noop (6) ntdomain: Checking for prefix before "\" (6) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (6) ntdomain: Found realm "CLEARSYSTEM" (6) ntdomain: Adding Stripped-User-Name = "test1" (6) ntdomain: Adding Realm = "CLEARSYSTEM" (6) ntdomain: Authentication realm is LOCAL (6) [ntdomain] = ok (6) eap: Peer sent EAP Response (code 2) ID 6 length 53 (6) eap: Continuing tunnel setup (6) [eap] = ok (6) } # authorize = ok (6) Found Auth-Type = eap (6) # Executing group from file /etc/raddb/sites-enabled/default (6) authenticate { (6) eap: Expiring EAP session with state 0x6d805dd768864438 (6) eap: Finished EAP session with state 0x6d805dd768864438 (6) eap: Previous EAP request found for state 0x6d805dd768864438, released from the list (6) eap: Peer sent packet with method EAP PEAP (25) (6) eap: Calling submodule eap_peap to process data (6) eap_peap: Continuing EAP-TLS (6) eap_peap: [eaptls verify] = ok (6) eap_peap: Done initial handshake (6) eap_peap: [eaptls process] = ok (6) eap_peap: Session established. Decoding tunneled attributes (6) eap_peap: PEAP state WAITING FOR INNER IDENTITY (6) eap_peap: Identity - CLEARSYSTEM\test1 (6) eap_peap: Got inner identity 'CLEARSYSTEM\test1' (6) eap_peap: Setting default EAP type for tunneled EAP session (6) eap_peap: Got tunneled request (6) eap_peap: EAP-Message = 0x0206001601434c45415253595354454d5c7465737431 (6) eap_peap: Setting User-Name to CLEARSYSTEM\test1 (6) eap_peap: Sending tunneled request to inner-tunnel (6) eap_peap: EAP-Message = 0x0206001601434c45415253595354454d5c7465737431 (6) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1 (6) eap_peap: User-Name = "CLEARSYSTEM\\test1" (6) Virtual server inner-tunnel received request (6) EAP-Message = 0x0206001601434c45415253595354454d5c7465737431 (6) FreeRADIUS-Proxied-To = 127.0.0.1 (6) User-Name = "CLEARSYSTEM\\test1" (6) WARNING: Outer and inner identities are the same. User privacy is compromised. (6) server inner-tunnel { (6) # Executing section authorize from file /etc/raddb/sites-enabled/inner-tunnel (6) authorize { (6) policy filter_username { (6) if (&User-Name) { (6) if (&User-Name) -> TRUE (6) if (&User-Name) { (6) if (&User-Name =~ / /) { (6) if (&User-Name =~ / /) -> FALSE (6) if (&User-Name =~ /@[^@]*@/ ) { (6) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (6) if (&User-Name =~ /\.\./ ) { (6) if (&User-Name =~ /\.\./ ) -> FALSE (6) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (6) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (6) if (&User-Name =~ /\.$/) { (6) if (&User-Name =~ /\.$/) -> FALSE (6) if (&User-Name =~ /(a)\./) { (6) if (&User-Name =~ /(a)\./) -> FALSE (6) } # if (&User-Name) = notfound (6) } # policy filter_username = notfound (6) [chap] = noop (6) [mschap] = noop (6) suffix: Checking for suffix after "@" (6) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (6) suffix: No such realm "NULL" (6) [suffix] = noop (6) ntdomain: Checking for prefix before "\" (6) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (6) ntdomain: Found realm "CLEARSYSTEM" (6) ntdomain: Adding Stripped-User-Name = "test1" (6) ntdomain: Adding Realm = "CLEARSYSTEM" (6) ntdomain: Authentication realm is LOCAL (6) [ntdomain] = ok (6) update control { (6) &Proxy-To-Realm := LOCAL (6) } # update control = noop (6) eap: Peer sent EAP Response (code 2) ID 6 length 22 (6) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize (6) [eap] = ok (6) } # authorize = ok (6) Found Auth-Type = eap (6) # Executing group from file /etc/raddb/sites-enabled/inner-tunnel (6) authenticate { (6) eap: Peer sent packet with method EAP Identity (1) (6) eap: Calling submodule eap_mschapv2 to process data (6) eap_mschapv2: Issuing Challenge (6) eap: Sending EAP Request (code 1) ID 7 length 43 (6) eap: EAP session adding &reply:State = 0x66e3bd0266e4a7fb (6) [eap] = handled (6) } # authenticate = handled (6) } # server inner-tunnel (6) Virtual server sending reply (6) EAP-Message = 0x0107002b1a01070026108d0fd294b2abb0cb4390aef8e7e334f0667265657261646975732d332e302e3133 (6) Message-Authenticator = 0x00000000000000000000000000000000 (6) State = 0x66e3bd0266e4a7fba16dc6bfc6cef435 (6) eap_peap: Got tunneled reply code 11 (6) eap_peap: EAP-Message = 0x0107002b1a01070026108d0fd294b2abb0cb4390aef8e7e334f0667265657261646975732d332e302e3133 (6) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (6) eap_peap: State = 0x66e3bd0266e4a7fba16dc6bfc6cef435 (6) eap_peap: Got tunneled reply RADIUS code 11 (6) eap_peap: EAP-Message = 0x0107002b1a01070026108d0fd294b2abb0cb4390aef8e7e334f0667265657261646975732d332e302e3133 (6) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (6) eap_peap: State = 0x66e3bd0266e4a7fba16dc6bfc6cef435 (6) eap_peap: Got tunneled Access-Challenge (6) eap: Sending EAP Request (code 1) ID 7 length 74 (6) eap: EAP session adding &reply:State = 0x6d805dd76b874438 (6) [eap] = handled (6) } # authenticate = handled (6) Using Post-Auth-Type Challenge (6) # Executing group from file /etc/raddb/sites-enabled/default (6) Challenge { ... } # empty sub-section is ignored (6) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (6) EAP-Message = 0x0107004a1900170303003fdc5fcf74a4d4ecf07ea22af536fa57cb428f1212cc762f73aecf7876928d4f6e657779a62eef9bc148c29f051acfe8f978bf7fcb45bcb1171b30e50382d3d3 (6) Message-Authenticator = 0x00000000000000000000000000000000 (6) State = 0x6d805dd76b874438dc40c2ae6afa62ac (6) Finished request Waking up in 4.9 seconds. (6) Cleaning up request packet ID 0 with timestamp +13 (7) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 250 (7) User-Name = "CLEARSYSTEM\\test1" (7) NAS-IP-Address = 172.22.22.254 (7) Called-Station-Id = "001601dfe596" (7) Calling-Station-Id = "74da38d41a8b" (7) NAS-Identifier = "001601dfe596" (7) NAS-Port = 5 (7) Framed-MTU = 1400 (7) State = 0x6d805dd76b874438dc40c2ae6afa62ac (7) NAS-Port-Type = Wireless-802.11 (7) EAP-Message = 0x0207006b19001703030060000000000000000219bae2d0668bb3eee9ce6bb0fc2eac4874e11bb450e239ca968d6460f050052b35bc8db55c8593cd55d4c2a998164b1c6b61a943bf0ef78db528fdd3f1dca0e8e07ff24916a4c37694cb22128f00feadf1aca1c1b2490214 (7) Message-Authenticator = 0x6f366ccc31737e80ff78cd36f016f96d (7) session-state: No cached attributes (7) # Executing section authorize from file /etc/raddb/sites-enabled/default (7) authorize { (7) policy filter_username { (7) if (&User-Name) { (7) if (&User-Name) -> TRUE (7) if (&User-Name) { (7) if (&User-Name =~ / /) { (7) if (&User-Name =~ / /) -> FALSE (7) if (&User-Name =~ /@[^@]*@/ ) { (7) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (7) if (&User-Name =~ /\.\./ ) { (7) if (&User-Name =~ /\.\./ ) -> FALSE (7) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (7) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (7) if (&User-Name =~ /\.$/) { (7) if (&User-Name =~ /\.$/) -> FALSE (7) if (&User-Name =~ /(a)\./) { (7) if (&User-Name =~ /(a)\./) -> FALSE (7) } # if (&User-Name) = notfound (7) } # policy filter_username = notfound (7) [preprocess] = ok (7) [chap] = noop (7) [mschap] = noop (7) [digest] = noop (7) suffix: Checking for suffix after "@" (7) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (7) suffix: No such realm "NULL" (7) [suffix] = noop (7) ntdomain: Checking for prefix before "\" (7) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (7) ntdomain: Found realm "CLEARSYSTEM" (7) ntdomain: Adding Stripped-User-Name = "test1" (7) ntdomain: Adding Realm = "CLEARSYSTEM" (7) ntdomain: Authentication realm is LOCAL (7) [ntdomain] = ok (7) eap: Peer sent EAP Response (code 2) ID 7 length 107 (7) eap: Continuing tunnel setup (7) [eap] = ok (7) } # authorize = ok (7) Found Auth-Type = eap (7) # Executing group from file /etc/raddb/sites-enabled/default (7) authenticate { (7) eap: Expiring EAP session with state 0x66e3bd0266e4a7fb (7) eap: Finished EAP session with state 0x6d805dd76b874438 (7) eap: Previous EAP request found for state 0x6d805dd76b874438, released from the list (7) eap: Peer sent packet with method EAP PEAP (25) (7) eap: Calling submodule eap_peap to process data (7) eap_peap: Continuing EAP-TLS (7) eap_peap: [eaptls verify] = ok (7) eap_peap: Done initial handshake (7) eap_peap: [eaptls process] = ok (7) eap_peap: Session established. Decoding tunneled attributes (7) eap_peap: PEAP state phase2 (7) eap_peap: EAP method MSCHAPv2 (26) (7) eap_peap: Got tunneled request (7) eap_peap: EAP-Message = 0x0207004c1a02070047313aedab25255aa4dcad5a9e911bf87fae00000000000000007d50d953955047745972cfe092bcc2c777fd52a69b03bebb00434c45415253595354454d5c7465737431 (7) eap_peap: Setting User-Name to CLEARSYSTEM\test1 (7) eap_peap: Sending tunneled request to inner-tunnel (7) eap_peap: EAP-Message = 0x0207004c1a02070047313aedab25255aa4dcad5a9e911bf87fae00000000000000007d50d953955047745972cfe092bcc2c777fd52a69b03bebb00434c45415253595354454d5c7465737431 (7) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1 (7) eap_peap: User-Name = "CLEARSYSTEM\\test1" (7) eap_peap: State = 0x66e3bd0266e4a7fba16dc6bfc6cef435 (7) Virtual server inner-tunnel received request (7) EAP-Message = 0x0207004c1a02070047313aedab25255aa4dcad5a9e911bf87fae00000000000000007d50d953955047745972cfe092bcc2c777fd52a69b03bebb00434c45415253595354454d5c7465737431 (7) FreeRADIUS-Proxied-To = 127.0.0.1 (7) User-Name = "CLEARSYSTEM\\test1" (7) State = 0x66e3bd0266e4a7fba16dc6bfc6cef435 (7) WARNING: Outer and inner identities are the same. User privacy is compromised. (7) server inner-tunnel { (7) session-state: No cached attributes (7) # Executing section authorize from file /etc/raddb/sites-enabled/inner-tunnel (7) authorize { (7) policy filter_username { (7) if (&User-Name) { (7) if (&User-Name) -> TRUE (7) if (&User-Name) { (7) if (&User-Name =~ / /) { (7) if (&User-Name =~ / /) -> FALSE (7) if (&User-Name =~ /@[^@]*@/ ) { (7) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (7) if (&User-Name =~ /\.\./ ) { (7) if (&User-Name =~ /\.\./ ) -> FALSE (7) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (7) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (7) if (&User-Name =~ /\.$/) { (7) if (&User-Name =~ /\.$/) -> FALSE (7) if (&User-Name =~ /(a)\./) { (7) if (&User-Name =~ /(a)\./) -> FALSE (7) } # if (&User-Name) = notfound (7) } # policy filter_username = notfound (7) [chap] = noop (7) [mschap] = noop (7) suffix: Checking for suffix after "@" (7) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (7) suffix: No such realm "NULL" (7) [suffix] = noop (7) ntdomain: Checking for prefix before "\" (7) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (7) ntdomain: Found realm "CLEARSYSTEM" (7) ntdomain: Adding Stripped-User-Name = "test1" (7) ntdomain: Adding Realm = "CLEARSYSTEM" (7) ntdomain: Authentication realm is LOCAL (7) [ntdomain] = ok (7) update control { (7) &Proxy-To-Realm := LOCAL (7) } # update control = noop (7) eap: Peer sent EAP Response (code 2) ID 7 length 76 (7) eap: No EAP Start, assuming it's an on-going EAP conversation (7) [eap] = updated (7) files: Searching for user in group "allusers" rlm_ldap (ldap): Reserved connection (0) (7) files: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (7) files: --> (uid=test1) (7) files: Performing search in "dc=system,dc=lan" with filter "(uid=test1)", scope "sub" (7) files: Waiting for search result... (7) files: User object found at DN "cn=test1 test1,ou=Users,ou=Accounts,dc=system,dc=lan" (7) files: Checking user object's memberOf attributes (7) files: Performing unfiltered search in "cn=test1 test1,ou=Users,ou=Accounts,dc=system,dc=lan", scope "base" (7) files: Waiting for search result... (7) files: Processing memberOf value "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (7) files: Resolving group DN "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (7) files: Performing unfiltered search in "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (7) files: Waiting for search result... (7) files: Group DN "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "ftp_plugin" (7) files: Processing memberOf value "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (7) files: Resolving group DN "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (7) files: Performing unfiltered search in "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (7) files: Waiting for search result... (7) files: Group DN "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "web_proxy_plugin" (7) files: Processing memberOf value "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (7) files: Resolving group DN "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (7) files: Performing unfiltered search in "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (7) files: Waiting for search result... (7) files: Group DN "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "webupload" (7) files: Processing memberOf value "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (7) files: Resolving group DN "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (7) files: Performing unfiltered search in "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (7) files: Waiting for search result... (7) files: Group DN "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "allusers" (7) files: User found in group "allusers". Comparison between membership: name (resolved from DN "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan"), check: name rlm_ldap (ldap): Released connection (0) (7) [files] = noop rlm_ldap (ldap): Reserved connection (1) (7) ldap: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (7) ldap: --> (uid=test1) (7) ldap: Performing search in "dc=system,dc=lan" with filter "(uid=test1)", scope "sub" (7) ldap: Waiting for search result... (7) ldap: User object found at DN "cn=test1 test1,ou=Users,ou=Accounts,dc=system,dc=lan" (7) ldap: Processing user attributes (7) ldap: control:Password-With-Header += '{sha}tESsBmE/yNY3lb6a0L6vVQEZNqw=' rlm_ldap (ldap): Released connection (1) (7) [ldap] = updated (7) [expiration] = noop (7) [logintime] = noop (7) pap: Converted: &control:Password-With-Header -> &control:SHA1-Password (7) pap: Removing &control:Password-With-Header (7) pap: Normalizing SHA1-Password from base64 encoding, 28 bytes -> 20 bytes (7) pap: WARNING: Auth-Type already set. Not setting to PAP (7) [pap] = noop (7) } # authorize = updated (7) Found Auth-Type = eap (7) # Executing group from file /etc/raddb/sites-enabled/inner-tunnel (7) authenticate { (7) eap: Expiring EAP session with state 0x66e3bd0266e4a7fb (7) eap: Finished EAP session with state 0x66e3bd0266e4a7fb (7) eap: Previous EAP request found for state 0x66e3bd0266e4a7fb, released from the list (7) eap: Peer sent packet with method EAP MSCHAPv2 (26) (7) eap: Calling submodule eap_mschapv2 to process data (7) eap_mschapv2: # Executing group from file /etc/raddb/sites-enabled/inner-tunnel (7) eap_mschapv2: authenticate { (7) mschap: Creating challenge hash with username: test1 (7) mschap: Client is using MS-CHAPv2 (7) mschap: Executing: /usr/bin/ntlm_auth --request-nt-key --username=%{%{Stripped-User-Name}:-%{%{User-Name}:-None}} --challenge=%{%{mschap:Challenge}:-00} --nt-response=%{%{mschap:NT-Response}:-00}: (7) mschap: EXPAND --username=%{%{Stripped-User-Name}:-%{%{User-Name}:-None}} (7) mschap: --> --username=test1 (7) mschap: Creating challenge hash with username: test1 (7) mschap: EXPAND --challenge=%{%{mschap:Challenge}:-00} (7) mschap: --> --challenge=3b9d7892b41cf3b0 (7) mschap: EXPAND --nt-response=%{%{mschap:NT-Response}:-00} (7) mschap: --> --nt-response=7d50d953955047745972cfe092bcc2c777fd52a69b03bebb (7) mschap: Program returned code (0) and output 'NT_KEY: DAE53F1776DBD0817C5639A27629A27D' (7) mschap: Adding MS-CHAPv2 MPPE keys (7) [mschap] = ok (7) } # authenticate = ok (7) MSCHAP Success (7) eap: Sending EAP Request (code 1) ID 8 length 51 (7) eap: EAP session adding &reply:State = 0x66e3bd0267eba7fb (7) [eap] = handled (7) } # authenticate = handled (7) } # server inner-tunnel (7) Virtual server sending reply (7) EAP-Message = 0x010800331a0307002e533d39313144313544453236303432433942464146394246343432383636363746354335423938343630 (7) Message-Authenticator = 0x00000000000000000000000000000000 (7) State = 0x66e3bd0267eba7fba16dc6bfc6cef435 (7) eap_peap: Got tunneled reply code 11 (7) eap_peap: EAP-Message = 0x010800331a0307002e533d39313144313544453236303432433942464146394246343432383636363746354335423938343630 (7) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (7) eap_peap: State = 0x66e3bd0267eba7fba16dc6bfc6cef435 (7) eap_peap: Got tunneled reply RADIUS code 11 (7) eap_peap: EAP-Message = 0x010800331a0307002e533d39313144313544453236303432433942464146394246343432383636363746354335423938343630 (7) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (7) eap_peap: State = 0x66e3bd0267eba7fba16dc6bfc6cef435 (7) eap_peap: Got tunneled Access-Challenge (7) eap: Sending EAP Request (code 1) ID 8 length 82 (7) eap: EAP session adding &reply:State = 0x6d805dd76a884438 (7) [eap] = handled (7) } # authenticate = handled (7) Using Post-Auth-Type Challenge (7) # Executing group from file /etc/raddb/sites-enabled/default (7) Challenge { ... } # empty sub-section is ignored (7) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (7) EAP-Message = 0x0108005219001703030047dc5fcf74a4d4ecf1ffeae2c864301f5752178e45427e243559fbf7f51b067715629d035309535ef9b4cbb1c8456cba01f0cd65f3a66724bec8cd596926856cc18e9a444620321d (7) Message-Authenticator = 0x00000000000000000000000000000000 (7) State = 0x6d805dd76a884438dc40c2ae6afa62ac (7) Finished request Waking up in 4.9 seconds. (7) Cleaning up request packet ID 0 with timestamp +13 (8) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 180 (8) User-Name = "CLEARSYSTEM\\test1" (8) NAS-IP-Address = 172.22.22.254 (8) Called-Station-Id = "001601dfe596" (8) Calling-Station-Id = "74da38d41a8b" (8) NAS-Identifier = "001601dfe596" (8) NAS-Port = 5 (8) Framed-MTU = 1400 (8) State = 0x6d805dd76a884438dc40c2ae6afa62ac (8) NAS-Port-Type = Wireless-802.11 (8) EAP-Message = 0x020800251900170303001a00000000000000034a80351d48d47617d97ab576bf0a41900ffa (8) Message-Authenticator = 0x8e3a7df7c36095515fae4cc97400d895 (8) session-state: No cached attributes (8) # Executing section authorize from file /etc/raddb/sites-enabled/default (8) authorize { (8) policy filter_username { (8) if (&User-Name) { (8) if (&User-Name) -> TRUE (8) if (&User-Name) { (8) if (&User-Name =~ / /) { (8) if (&User-Name =~ / /) -> FALSE (8) if (&User-Name =~ /@[^@]*@/ ) { (8) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (8) if (&User-Name =~ /\.\./ ) { (8) if (&User-Name =~ /\.\./ ) -> FALSE (8) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (8) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (8) if (&User-Name =~ /\.$/) { (8) if (&User-Name =~ /\.$/) -> FALSE (8) if (&User-Name =~ /(a)\./) { (8) if (&User-Name =~ /(a)\./) -> FALSE (8) } # if (&User-Name) = notfound (8) } # policy filter_username = notfound (8) [preprocess] = ok (8) [chap] = noop (8) [mschap] = noop (8) [digest] = noop (8) suffix: Checking for suffix after "@" (8) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (8) suffix: No such realm "NULL" (8) [suffix] = noop (8) ntdomain: Checking for prefix before "\" (8) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (8) ntdomain: Found realm "CLEARSYSTEM" (8) ntdomain: Adding Stripped-User-Name = "test1" (8) ntdomain: Adding Realm = "CLEARSYSTEM" (8) ntdomain: Authentication realm is LOCAL (8) [ntdomain] = ok (8) eap: Peer sent EAP Response (code 2) ID 8 length 37 (8) eap: Continuing tunnel setup (8) [eap] = ok (8) } # authorize = ok (8) Found Auth-Type = eap (8) # Executing group from file /etc/raddb/sites-enabled/default (8) authenticate { (8) eap: Expiring EAP session with state 0x66e3bd0267eba7fb (8) eap: Finished EAP session with state 0x6d805dd76a884438 (8) eap: Previous EAP request found for state 0x6d805dd76a884438, released from the list (8) eap: Peer sent packet with method EAP PEAP (25) (8) eap: Calling submodule eap_peap to process data (8) eap_peap: Continuing EAP-TLS (8) eap_peap: [eaptls verify] = ok (8) eap_peap: Done initial handshake (8) eap_peap: [eaptls process] = ok (8) eap_peap: Session established. Decoding tunneled attributes (8) eap_peap: PEAP state phase2 (8) eap_peap: EAP method MSCHAPv2 (26) (8) eap_peap: Got tunneled request (8) eap_peap: EAP-Message = 0x020800061a03 (8) eap_peap: Setting User-Name to CLEARSYSTEM\test1 (8) eap_peap: Sending tunneled request to inner-tunnel (8) eap_peap: EAP-Message = 0x020800061a03 (8) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1 (8) eap_peap: User-Name = "CLEARSYSTEM\\test1" (8) eap_peap: State = 0x66e3bd0267eba7fba16dc6bfc6cef435 (8) Virtual server inner-tunnel received request (8) EAP-Message = 0x020800061a03 (8) FreeRADIUS-Proxied-To = 127.0.0.1 (8) User-Name = "CLEARSYSTEM\\test1" (8) State = 0x66e3bd0267eba7fba16dc6bfc6cef435 (8) WARNING: Outer and inner identities are the same. User privacy is compromised. (8) server inner-tunnel { (8) session-state: No cached attributes (8) # Executing section authorize from file /etc/raddb/sites-enabled/inner-tunnel (8) authorize { (8) policy filter_username { (8) if (&User-Name) { (8) if (&User-Name) -> TRUE (8) if (&User-Name) { (8) if (&User-Name =~ / /) { (8) if (&User-Name =~ / /) -> FALSE (8) if (&User-Name =~ /@[^@]*@/ ) { (8) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (8) if (&User-Name =~ /\.\./ ) { (8) if (&User-Name =~ /\.\./ ) -> FALSE (8) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (8) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (8) if (&User-Name =~ /\.$/) { (8) if (&User-Name =~ /\.$/) -> FALSE (8) if (&User-Name =~ /(a)\./) { (8) if (&User-Name =~ /(a)\./) -> FALSE (8) } # if (&User-Name) = notfound (8) } # policy filter_username = notfound (8) [chap] = noop (8) [mschap] = noop (8) suffix: Checking for suffix after "@" (8) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (8) suffix: No such realm "NULL" (8) [suffix] = noop (8) ntdomain: Checking for prefix before "\" (8) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (8) ntdomain: Found realm "CLEARSYSTEM" (8) ntdomain: Adding Stripped-User-Name = "test1" (8) ntdomain: Adding Realm = "CLEARSYSTEM" (8) ntdomain: Authentication realm is LOCAL (8) [ntdomain] = ok (8) update control { (8) &Proxy-To-Realm := LOCAL (8) } # update control = noop (8) eap: Peer sent EAP Response (code 2) ID 8 length 6 (8) eap: No EAP Start, assuming it's an on-going EAP conversation (8) [eap] = updated (8) files: Searching for user in group "allusers" rlm_ldap (ldap): Reserved connection (2) (8) files: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (8) files: --> (uid=test1) (8) files: Performing search in "dc=system,dc=lan" with filter "(uid=test1)", scope "sub" (8) files: Waiting for search result... (8) files: User object found at DN "cn=test1 test1,ou=Users,ou=Accounts,dc=system,dc=lan" (8) files: Checking user object's memberOf attributes (8) files: Performing unfiltered search in "cn=test1 test1,ou=Users,ou=Accounts,dc=system,dc=lan", scope "base" (8) files: Waiting for search result... (8) files: Processing memberOf value "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (8) files: Resolving group DN "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (8) files: Performing unfiltered search in "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (8) files: Waiting for search result... (8) files: Group DN "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "ftp_plugin" (8) files: Processing memberOf value "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (8) files: Resolving group DN "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (8) files: Performing unfiltered search in "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (8) files: Waiting for search result... (8) files: Group DN "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "web_proxy_plugin" (8) files: Processing memberOf value "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (8) files: Resolving group DN "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (8) files: Performing unfiltered search in "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (8) files: Waiting for search result... (8) files: Group DN "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "webupload" (8) files: Processing memberOf value "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (8) files: Resolving group DN "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (8) files: Performing unfiltered search in "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (8) files: Waiting for search result... (8) files: Group DN "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "allusers" (8) files: User found in group "allusers". Comparison between membership: name (resolved from DN "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan"), check: name rlm_ldap (ldap): Released connection (2) (8) [files] = noop rlm_ldap (ldap): Reserved connection (3) (8) ldap: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (8) ldap: --> (uid=test1) (8) ldap: Performing search in "dc=system,dc=lan" with filter "(uid=test1)", scope "sub" (8) ldap: Waiting for search result... (8) ldap: User object found at DN "cn=test1 test1,ou=Users,ou=Accounts,dc=system,dc=lan" (8) ldap: Processing user attributes (8) ldap: control:Password-With-Header += '{sha}tESsBmE/yNY3lb6a0L6vVQEZNqw=' rlm_ldap (ldap): Released connection (3) (8) [ldap] = updated (8) [expiration] = noop (8) [logintime] = noop (8) pap: Converted: &control:Password-With-Header -> &control:SHA1-Password (8) pap: Removing &control:Password-With-Header (8) pap: Normalizing SHA1-Password from base64 encoding, 28 bytes -> 20 bytes (8) pap: WARNING: Auth-Type already set. Not setting to PAP (8) [pap] = noop (8) } # authorize = updated (8) Found Auth-Type = eap (8) # Executing group from file /etc/raddb/sites-enabled/inner-tunnel (8) authenticate { (8) eap: Expiring EAP session with state 0x66e3bd0267eba7fb (8) eap: Finished EAP session with state 0x66e3bd0267eba7fb (8) eap: Previous EAP request found for state 0x66e3bd0267eba7fb, released from the list (8) eap: Peer sent packet with method EAP MSCHAPv2 (26) (8) eap: Calling submodule eap_mschapv2 to process data (8) eap: Sending EAP Success (code 3) ID 8 length 4 (8) eap: Freeing handler (8) [eap] = ok (8) } # authenticate = ok (8) # Executing section post-auth from file /etc/raddb/sites-enabled/inner-tunnel (8) post-auth { (8) if (0) { (8) if (0) -> FALSE (8) } # post-auth = noop (8) } # server inner-tunnel (8) Virtual server sending reply (8) MS-MPPE-Encryption-Policy = Encryption-Allowed (8) MS-MPPE-Encryption-Types = RC4-40or128-bit-Allowed (8) MS-MPPE-Send-Key = 0xb0cef0c8f31ece219ae921fa8dd00a05 (8) MS-MPPE-Recv-Key = 0x0c0cf49c321e6e908780b3c6612b6feb (8) EAP-Message = 0x03080004 (8) Message-Authenticator = 0x00000000000000000000000000000000 (8) Stripped-User-Name = "test1" (8) eap_peap: Got tunneled reply code 2 (8) eap_peap: MS-MPPE-Encryption-Policy = Encryption-Allowed (8) eap_peap: MS-MPPE-Encryption-Types = RC4-40or128-bit-Allowed (8) eap_peap: MS-MPPE-Send-Key = 0xb0cef0c8f31ece219ae921fa8dd00a05 (8) eap_peap: MS-MPPE-Recv-Key = 0x0c0cf49c321e6e908780b3c6612b6feb (8) eap_peap: EAP-Message = 0x03080004 (8) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (8) eap_peap: Stripped-User-Name = "test1" (8) eap_peap: Got tunneled reply RADIUS code 2 (8) eap_peap: MS-MPPE-Encryption-Policy = Encryption-Allowed (8) eap_peap: MS-MPPE-Encryption-Types = RC4-40or128-bit-Allowed (8) eap_peap: MS-MPPE-Send-Key = 0xb0cef0c8f31ece219ae921fa8dd00a05 (8) eap_peap: MS-MPPE-Recv-Key = 0x0c0cf49c321e6e908780b3c6612b6feb (8) eap_peap: EAP-Message = 0x03080004 (8) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (8) eap_peap: Stripped-User-Name = "test1" (8) eap_peap: Tunneled authentication was successful (8) eap_peap: SUCCESS (8) eap: Sending EAP Request (code 1) ID 9 length 46 (8) eap: EAP session adding &reply:State = 0x6d805dd765894438 (8) [eap] = handled (8) } # authenticate = handled (8) Using Post-Auth-Type Challenge (8) # Executing group from file /etc/raddb/sites-enabled/default (8) Challenge { ... } # empty sub-section is ignored (8) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (8) EAP-Message = 0x0109002e19001703030023dc5fcf74a4d4ecf2e22cf6f1b9c7c262e75a225086d46b3b1094d6a2e54fad0e208021 (8) Message-Authenticator = 0x00000000000000000000000000000000 (8) State = 0x6d805dd765894438dc40c2ae6afa62ac (8) Finished request Waking up in 4.9 seconds. (8) Cleaning up request packet ID 0 with timestamp +13 (9) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 189 (9) User-Name = "CLEARSYSTEM\\test1" (9) NAS-IP-Address = 172.22.22.254 (9) Called-Station-Id = "001601dfe596" (9) Calling-Station-Id = "74da38d41a8b" (9) NAS-Identifier = "001601dfe596" (9) NAS-Port = 5 (9) Framed-MTU = 1400 (9) State = 0x6d805dd765894438dc40c2ae6afa62ac (9) NAS-Port-Type = Wireless-802.11 (9) EAP-Message = 0x0209002e190017030300230000000000000004274d7c08364b6d55ee3aa706f66f7126d6c1243d8d08bdbd7a9051 (9) Message-Authenticator = 0x36b35cb4fd0f6af8a94dfc86605dc543 (9) session-state: No cached attributes (9) # Executing section authorize from file /etc/raddb/sites-enabled/default (9) authorize { (9) policy filter_username { (9) if (&User-Name) { (9) if (&User-Name) -> TRUE (9) if (&User-Name) { (9) if (&User-Name =~ / /) { (9) if (&User-Name =~ / /) -> FALSE (9) if (&User-Name =~ /@[^@]*@/ ) { (9) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (9) if (&User-Name =~ /\.\./ ) { (9) if (&User-Name =~ /\.\./ ) -> FALSE (9) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (9) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (9) if (&User-Name =~ /\.$/) { (9) if (&User-Name =~ /\.$/) -> FALSE (9) if (&User-Name =~ /(a)\./) { (9) if (&User-Name =~ /(a)\./) -> FALSE (9) } # if (&User-Name) = notfound (9) } # policy filter_username = notfound (9) [preprocess] = ok (9) [chap] = noop (9) [mschap] = noop (9) [digest] = noop (9) suffix: Checking for suffix after "@" (9) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (9) suffix: No such realm "NULL" (9) [suffix] = noop (9) ntdomain: Checking for prefix before "\" (9) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (9) ntdomain: Found realm "CLEARSYSTEM" (9) ntdomain: Adding Stripped-User-Name = "test1" (9) ntdomain: Adding Realm = "CLEARSYSTEM" (9) ntdomain: Authentication realm is LOCAL (9) [ntdomain] = ok (9) eap: Peer sent EAP Response (code 2) ID 9 length 46 (9) eap: Continuing tunnel setup (9) [eap] = ok (9) } # authorize = ok (9) Found Auth-Type = eap (9) # Executing group from file /etc/raddb/sites-enabled/default (9) authenticate { (9) eap: Expiring EAP session with state 0x6d805dd765894438 (9) eap: Finished EAP session with state 0x6d805dd765894438 (9) eap: Previous EAP request found for state 0x6d805dd765894438, released from the list (9) eap: Peer sent packet with method EAP PEAP (25) (9) eap: Calling submodule eap_peap to process data (9) eap_peap: Continuing EAP-TLS (9) eap_peap: [eaptls verify] = ok (9) eap_peap: Done initial handshake (9) eap_peap: [eaptls process] = ok (9) eap_peap: Session established. Decoding tunneled attributes (9) eap_peap: PEAP state send tlv success (9) eap_peap: Received EAP-TLV response (9) eap_peap: Success (9) eap: Sending EAP Success (code 3) ID 9 length 4 (9) eap: Freeing handler (9) [eap] = ok (9) } # authenticate = ok (9) # Executing section post-auth from file /etc/raddb/sites-enabled/default (9) post-auth { (9) update { (9) No attributes updated (9) } # update = noop (9) [exec] = noop (9) policy remove_reply_message_if_eap { (9) if (&reply:EAP-Message && &reply:Reply-Message) { (9) if (&reply:EAP-Message && &reply:Reply-Message) -> FALSE (9) else { (9) [noop] = noop (9) } # else = noop (9) } # policy remove_reply_message_if_eap = noop (9) } # post-auth = noop (9) Sent Access-Accept Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (9) MS-MPPE-Recv-Key = 0x0790725f316f49070c1b7729230cfb972a484adc36a235b208c4550295ea4187 (9) MS-MPPE-Send-Key = 0x92b2a51d0e06c17fdefa0e17bdc1efe33e5aae270f461bf4828d6fb2de315a80 (9) EAP-Message = 0x03090004 (9) Message-Authenticator = 0x00000000000000000000000000000000 (9) Finished request Waking up in 4.9 seconds. (9) Cleaning up request packet ID 0 with timestamp +13 Ready to process requests (10) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 147 (10) User-Name = "CLEARSYSTEM\\test1" (10) NAS-IP-Address = 172.22.22.254 (10) Called-Station-Id = "001601dfe596" (10) Calling-Station-Id = "74da38d41a8b" (10) NAS-Identifier = "001601dfe596" (10) NAS-Port = 5 (10) Framed-MTU = 1400 (10) NAS-Port-Type = Wireless-802.11 (10) EAP-Message = 0x0200001601434c45415253595354454d5c7465737431 (10) Message-Authenticator = 0x3e663781d018a3da35a626dc52214957 (10) # Executing section authorize from file /etc/raddb/sites-enabled/default (10) authorize { (10) policy filter_username { (10) if (&User-Name) { (10) if (&User-Name) -> TRUE (10) if (&User-Name) { (10) if (&User-Name =~ / /) { (10) if (&User-Name =~ / /) -> FALSE (10) if (&User-Name =~ /@[^@]*@/ ) { (10) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (10) if (&User-Name =~ /\.\./ ) { (10) if (&User-Name =~ /\.\./ ) -> FALSE (10) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (10) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (10) if (&User-Name =~ /\.$/) { (10) if (&User-Name =~ /\.$/) -> FALSE (10) if (&User-Name =~ /(a)\./) { (10) if (&User-Name =~ /(a)\./) -> FALSE (10) } # if (&User-Name) = notfound (10) } # policy filter_username = notfound (10) [preprocess] = ok (10) [chap] = noop (10) [mschap] = noop (10) [digest] = noop (10) suffix: Checking for suffix after "@" (10) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (10) suffix: No such realm "NULL" (10) [suffix] = noop (10) ntdomain: Checking for prefix before "\" (10) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (10) ntdomain: Found realm "CLEARSYSTEM" (10) ntdomain: Adding Stripped-User-Name = "test1" (10) ntdomain: Adding Realm = "CLEARSYSTEM" (10) ntdomain: Authentication realm is LOCAL (10) [ntdomain] = ok (10) eap: Peer sent EAP Response (code 2) ID 0 length 22 (10) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize (10) [eap] = ok (10) } # authorize = ok (10) Found Auth-Type = eap (10) # Executing group from file /etc/raddb/sites-enabled/default (10) authenticate { (10) eap: Peer sent packet with method EAP Identity (1) (10) eap: Calling submodule eap_peap to process data (10) eap_peap: Initiating new EAP-TLS session (10) eap_peap: [eaptls start] = request (10) eap: Sending EAP Request (code 1) ID 1 length 6 (10) eap: EAP session adding &reply:State = 0x5205bbdd5204a286 (10) [eap] = handled (10) } # authenticate = handled (10) Using Post-Auth-Type Challenge (10) # Executing group from file /etc/raddb/sites-enabled/default (10) Challenge { ... } # empty sub-section is ignored (10) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (10) EAP-Message = 0x010100061920 (10) Message-Authenticator = 0x00000000000000000000000000000000 (10) State = 0x5205bbdd5204a286e7a44a448065710e (10) Finished request Waking up in 4.9 seconds. (10) Cleaning up request packet ID 0 with timestamp +44 (11) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 309 (11) User-Name = "CLEARSYSTEM\\test1" (11) NAS-IP-Address = 172.22.22.254 (11) Called-Station-Id = "001601dfe596" (11) Calling-Station-Id = "74da38d41a8b" (11) NAS-Identifier = "001601dfe596" (11) NAS-Port = 5 (11) Framed-MTU = 1400 (11) State = 0x5205bbdd5204a286e7a44a448065710e (11) NAS-Port-Type = Wireless-802.11 (11) EAP-Message = 0x020100a619800000009c16030300970100009303035af2cd38a6bde90cac89c6193a2d76d271c9604c7ddfed3814c78b24ba8f7e5c00002ac02cc02bc030c02f009f009ec024c023c028c027c00ac009c014c013009d009c003d003c0035002f000a01000040000500050100000000000a00080006001d (11) Message-Authenticator = 0xaed2c29e86157e53d66c93b98a2a81d6 (11) session-state: No cached attributes (11) # Executing section authorize from file /etc/raddb/sites-enabled/default (11) authorize { (11) policy filter_username { (11) if (&User-Name) { (11) if (&User-Name) -> TRUE (11) if (&User-Name) { (11) if (&User-Name =~ / /) { (11) if (&User-Name =~ / /) -> FALSE (11) if (&User-Name =~ /@[^@]*@/ ) { (11) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (11) if (&User-Name =~ /\.\./ ) { (11) if (&User-Name =~ /\.\./ ) -> FALSE (11) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (11) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (11) if (&User-Name =~ /\.$/) { (11) if (&User-Name =~ /\.$/) -> FALSE (11) if (&User-Name =~ /(a)\./) { (11) if (&User-Name =~ /(a)\./) -> FALSE (11) } # if (&User-Name) = notfound (11) } # policy filter_username = notfound (11) [preprocess] = ok (11) [chap] = noop (11) [mschap] = noop (11) [digest] = noop (11) suffix: Checking for suffix after "@" (11) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (11) suffix: No such realm "NULL" (11) [suffix] = noop (11) ntdomain: Checking for prefix before "\" (11) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (11) ntdomain: Found realm "CLEARSYSTEM" (11) ntdomain: Adding Stripped-User-Name = "test1" (11) ntdomain: Adding Realm = "CLEARSYSTEM" (11) ntdomain: Authentication realm is LOCAL (11) [ntdomain] = ok (11) eap: Peer sent EAP Response (code 2) ID 1 length 166 (11) eap: Continuing tunnel setup (11) [eap] = ok (11) } # authorize = ok (11) Found Auth-Type = eap (11) # Executing group from file /etc/raddb/sites-enabled/default (11) authenticate { (11) eap: Expiring EAP session with state 0x5205bbdd5204a286 (11) eap: Finished EAP session with state 0x5205bbdd5204a286 (11) eap: Previous EAP request found for state 0x5205bbdd5204a286, released from the list (11) eap: Peer sent packet with method EAP PEAP (25) (11) eap: Calling submodule eap_peap to process data (11) eap_peap: Continuing EAP-TLS (11) eap_peap: Peer indicated complete TLS record size will be 156 bytes (11) eap_peap: Got complete TLS record (156 bytes) (11) eap_peap: [eaptls verify] = length included (11) eap_peap: (other): before/accept initialization (11) eap_peap: TLS_accept: before/accept initialization (11) eap_peap: <<< recv TLS 1.2 [length 0097] (11) eap_peap: TLS_accept: SSLv3 read client hello A (11) eap_peap: >>> send TLS 1.2 [length 0039] (11) eap_peap: TLS_accept: SSLv3 write server hello A (11) eap_peap: >>> send TLS 1.2 [length 08bd] (11) eap_peap: TLS_accept: SSLv3 write certificate A (11) eap_peap: >>> send TLS 1.2 [length 014d] (11) eap_peap: TLS_accept: SSLv3 write key exchange A (11) eap_peap: >>> send TLS 1.2 [length 0004] (11) eap_peap: TLS_accept: SSLv3 write server done A (11) eap_peap: TLS_accept: SSLv3 flush data (11) eap_peap: TLS_accept: SSLv3 read client certificate A (11) eap_peap: TLS_accept: Need to read more data: SSLv3 read client key exchange A (11) eap_peap: TLS_accept: Need to read more data: SSLv3 read client key exchange A (11) eap_peap: In SSL Handshake Phase (11) eap_peap: In SSL Accept mode (11) eap_peap: [eaptls process] = handled (11) eap: Sending EAP Request (code 1) ID 2 length 1004 (11) eap: EAP session adding &reply:State = 0x5205bbdd5307a286 (11) [eap] = handled (11) } # authenticate = handled (11) Using Post-Auth-Type Challenge (11) # Executing group from file /etc/raddb/sites-enabled/default (11) Challenge { ... } # empty sub-section is ignored (11) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (11) EAP-Message = 0x010203ec19c000000a5b1603030039020000350303b03cc28858b129d2eb2e9017deb4a9a6acdbb87cb5a0dbbed57be74b9ad0b07800c03000000dff01000100000b00040300010216030308bd0b0008b90008b60003fb308203f7308202dfa003020102020101300d06092a864886f70d01010b050030 (11) Message-Authenticator = 0x00000000000000000000000000000000 (11) State = 0x5205bbdd5307a286e7a44a448065710e (11) Finished request Waking up in 4.9 seconds. (11) Cleaning up request packet ID 0 with timestamp +44 (12) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 149 (12) User-Name = "CLEARSYSTEM\\test1" (12) NAS-IP-Address = 172.22.22.254 (12) Called-Station-Id = "001601dfe596" (12) Calling-Station-Id = "74da38d41a8b" (12) NAS-Identifier = "001601dfe596" (12) NAS-Port = 5 (12) Framed-MTU = 1400 (12) State = 0x5205bbdd5307a286e7a44a448065710e (12) NAS-Port-Type = Wireless-802.11 (12) EAP-Message = 0x020200061900 (12) Message-Authenticator = 0x2316426b772c524a5666fca10c78a6f7 (12) session-state: No cached attributes (12) # Executing section authorize from file /etc/raddb/sites-enabled/default (12) authorize { (12) policy filter_username { (12) if (&User-Name) { (12) if (&User-Name) -> TRUE (12) if (&User-Name) { (12) if (&User-Name =~ / /) { (12) if (&User-Name =~ / /) -> FALSE (12) if (&User-Name =~ /@[^@]*@/ ) { (12) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (12) if (&User-Name =~ /\.\./ ) { (12) if (&User-Name =~ /\.\./ ) -> FALSE (12) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (12) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (12) if (&User-Name =~ /\.$/) { (12) if (&User-Name =~ /\.$/) -> FALSE (12) if (&User-Name =~ /(a)\./) { (12) if (&User-Name =~ /(a)\./) -> FALSE (12) } # if (&User-Name) = notfound (12) } # policy filter_username = notfound (12) [preprocess] = ok (12) [chap] = noop (12) [mschap] = noop (12) [digest] = noop (12) suffix: Checking for suffix after "@" (12) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (12) suffix: No such realm "NULL" (12) [suffix] = noop (12) ntdomain: Checking for prefix before "\" (12) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (12) ntdomain: Found realm "CLEARSYSTEM" (12) ntdomain: Adding Stripped-User-Name = "test1" (12) ntdomain: Adding Realm = "CLEARSYSTEM" (12) ntdomain: Authentication realm is LOCAL (12) [ntdomain] = ok (12) eap: Peer sent EAP Response (code 2) ID 2 length 6 (12) eap: Continuing tunnel setup (12) [eap] = ok (12) } # authorize = ok (12) Found Auth-Type = eap (12) # Executing group from file /etc/raddb/sites-enabled/default (12) authenticate { (12) eap: Expiring EAP session with state 0x5205bbdd5307a286 (12) eap: Finished EAP session with state 0x5205bbdd5307a286 (12) eap: Previous EAP request found for state 0x5205bbdd5307a286, released from the list (12) eap: Peer sent packet with method EAP PEAP (25) (12) eap: Calling submodule eap_peap to process data (12) eap_peap: Continuing EAP-TLS (12) eap_peap: Peer ACKed our handshake fragment (12) eap_peap: [eaptls verify] = request (12) eap_peap: [eaptls process] = handled (12) eap: Sending EAP Request (code 1) ID 3 length 1000 (12) eap: EAP session adding &reply:State = 0x5205bbdd5006a286 (12) [eap] = handled (12) } # authenticate = handled (12) Using Post-Auth-Type Challenge (12) # Executing group from file /etc/raddb/sites-enabled/default (12) Challenge { ... } # empty sub-section is ignored (12) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (12) EAP-Message = 0x010303e819408444f5b804aa2d65ef2b23820bb1bf1bfcb24df6bd03eabe61d7bb630cfd9fd6165d19f24d23925593c04c7ec13d5afe51369fe487605e2de3073d043a15e72448712bca946e329e81ff36cebcdfe8be08dc6490da38ed9147e7eac88af7f25487bee0ef80700004b5308204b130820399 (12) Message-Authenticator = 0x00000000000000000000000000000000 (12) State = 0x5205bbdd5006a286e7a44a448065710e (12) Finished request Waking up in 4.9 seconds. (12) Cleaning up request packet ID 0 with timestamp +44 (13) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 149 (13) User-Name = "CLEARSYSTEM\\test1" (13) NAS-IP-Address = 172.22.22.254 (13) Called-Station-Id = "001601dfe596" (13) Calling-Station-Id = "74da38d41a8b" (13) NAS-Identifier = "001601dfe596" (13) NAS-Port = 5 (13) Framed-MTU = 1400 (13) State = 0x5205bbdd5006a286e7a44a448065710e (13) NAS-Port-Type = Wireless-802.11 (13) EAP-Message = 0x020300061900 (13) Message-Authenticator = 0xb6167b86da6c3a72a5fa00cbb2898a5c (13) session-state: No cached attributes (13) # Executing section authorize from file /etc/raddb/sites-enabled/default (13) authorize { (13) policy filter_username { (13) if (&User-Name) { (13) if (&User-Name) -> TRUE (13) if (&User-Name) { (13) if (&User-Name =~ / /) { (13) if (&User-Name =~ / /) -> FALSE (13) if (&User-Name =~ /@[^@]*@/ ) { (13) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (13) if (&User-Name =~ /\.\./ ) { (13) if (&User-Name =~ /\.\./ ) -> FALSE (13) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (13) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (13) if (&User-Name =~ /\.$/) { (13) if (&User-Name =~ /\.$/) -> FALSE (13) if (&User-Name =~ /(a)\./) { (13) if (&User-Name =~ /(a)\./) -> FALSE (13) } # if (&User-Name) = notfound (13) } # policy filter_username = notfound (13) [preprocess] = ok (13) [chap] = noop (13) [mschap] = noop (13) [digest] = noop (13) suffix: Checking for suffix after "@" (13) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (13) suffix: No such realm "NULL" (13) [suffix] = noop (13) ntdomain: Checking for prefix before "\" (13) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (13) ntdomain: Found realm "CLEARSYSTEM" (13) ntdomain: Adding Stripped-User-Name = "test1" (13) ntdomain: Adding Realm = "CLEARSYSTEM" (13) ntdomain: Authentication realm is LOCAL (13) [ntdomain] = ok (13) eap: Peer sent EAP Response (code 2) ID 3 length 6 (13) eap: Continuing tunnel setup (13) [eap] = ok (13) } # authorize = ok (13) Found Auth-Type = eap (13) # Executing group from file /etc/raddb/sites-enabled/default (13) authenticate { (13) eap: Expiring EAP session with state 0x5205bbdd5006a286 (13) eap: Finished EAP session with state 0x5205bbdd5006a286 (13) eap: Previous EAP request found for state 0x5205bbdd5006a286, released from the list (13) eap: Peer sent packet with method EAP PEAP (25) (13) eap: Calling submodule eap_peap to process data (13) eap_peap: Continuing EAP-TLS (13) eap_peap: Peer ACKed our handshake fragment (13) eap_peap: [eaptls verify] = request (13) eap_peap: [eaptls process] = handled (13) eap: Sending EAP Request (code 1) ID 4 length 669 (13) eap: EAP session adding &reply:State = 0x5205bbdd5101a286 (13) [eap] = handled (13) } # authenticate = handled (13) Using Post-Auth-Type Challenge (13) # Executing group from file /etc/raddb/sites-enabled/default (13) Challenge { ... } # empty sub-section is ignored (13) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (13) EAP-Message = 0x0104029d1900278625687474703a2f2f7777772e6578616d706c652e6f72672f6578616d706c655f63612e63726c300d06092a864886f70d01010b050003820101000132a42023b4da19cd0464809979cba06e09409f4cbae9db226b41b48d0c97de8fa6092c00476cb9f16399e310996fb68c40e69b10 (13) Message-Authenticator = 0x00000000000000000000000000000000 (13) State = 0x5205bbdd5101a286e7a44a448065710e (13) Finished request Waking up in 4.9 seconds. (13) Cleaning up request packet ID 0 with timestamp +44 (14) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 279 (14) User-Name = "CLEARSYSTEM\\test1" (14) NAS-IP-Address = 172.22.22.254 (14) Called-Station-Id = "001601dfe596" (14) Calling-Station-Id = "74da38d41a8b" (14) NAS-Identifier = "001601dfe596" (14) NAS-Port = 5 (14) Framed-MTU = 1400 (14) State = 0x5205bbdd5101a286e7a44a448065710e (14) NAS-Port-Type = Wireless-802.11 (14) EAP-Message = 0x0204008819800000007e1603030046100000424104e75ed2454d55c1c56f5300e806d9964d68478eeb7c9f1af4e5695daeb6fa5f3f968c3621984b9fc4079a2bf4e7ace9f798901c2c1b52cbad15600761a017196b14030300010116030300280000000000000000a90ea118db4e321e4fd9a1f90e76ef (14) Message-Authenticator = 0x2254305b780a66f1e2c8b4c87549e709 (14) session-state: No cached attributes (14) # Executing section authorize from file /etc/raddb/sites-enabled/default (14) authorize { (14) policy filter_username { (14) if (&User-Name) { (14) if (&User-Name) -> TRUE (14) if (&User-Name) { (14) if (&User-Name =~ / /) { (14) if (&User-Name =~ / /) -> FALSE (14) if (&User-Name =~ /@[^@]*@/ ) { (14) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (14) if (&User-Name =~ /\.\./ ) { (14) if (&User-Name =~ /\.\./ ) -> FALSE (14) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (14) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (14) if (&User-Name =~ /\.$/) { (14) if (&User-Name =~ /\.$/) -> FALSE (14) if (&User-Name =~ /(a)\./) { (14) if (&User-Name =~ /(a)\./) -> FALSE (14) } # if (&User-Name) = notfound (14) } # policy filter_username = notfound (14) [preprocess] = ok (14) [chap] = noop (14) [mschap] = noop (14) [digest] = noop (14) suffix: Checking for suffix after "@" (14) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (14) suffix: No such realm "NULL" (14) [suffix] = noop (14) ntdomain: Checking for prefix before "\" (14) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (14) ntdomain: Found realm "CLEARSYSTEM" (14) ntdomain: Adding Stripped-User-Name = "test1" (14) ntdomain: Adding Realm = "CLEARSYSTEM" (14) ntdomain: Authentication realm is LOCAL (14) [ntdomain] = ok (14) eap: Peer sent EAP Response (code 2) ID 4 length 136 (14) eap: Continuing tunnel setup (14) [eap] = ok (14) } # authorize = ok (14) Found Auth-Type = eap (14) # Executing group from file /etc/raddb/sites-enabled/default (14) authenticate { (14) eap: Expiring EAP session with state 0x5205bbdd5101a286 (14) eap: Finished EAP session with state 0x5205bbdd5101a286 (14) eap: Previous EAP request found for state 0x5205bbdd5101a286, released from the list (14) eap: Peer sent packet with method EAP PEAP (25) (14) eap: Calling submodule eap_peap to process data (14) eap_peap: Continuing EAP-TLS (14) eap_peap: Peer indicated complete TLS record size will be 126 bytes (14) eap_peap: Got complete TLS record (126 bytes) (14) eap_peap: [eaptls verify] = length included (14) eap_peap: <<< recv TLS 1.2 [length 0046] (14) eap_peap: TLS_accept: SSLv3 read client key exchange A (14) eap_peap: TLS_accept: SSLv3 read certificate verify A (14) eap_peap: <<< recv TLS 1.2 [length 0001] (14) eap_peap: <<< recv TLS 1.2 [length 0010] (14) eap_peap: TLS_accept: SSLv3 read finished A (14) eap_peap: >>> send TLS 1.2 [length 0001] (14) eap_peap: TLS_accept: SSLv3 write change cipher spec A (14) eap_peap: >>> send TLS 1.2 [length 0010] (14) eap_peap: TLS_accept: SSLv3 write finished A (14) eap_peap: TLS_accept: SSLv3 flush data (14) eap_peap: (other): SSL negotiation finished successfully (14) eap_peap: SSL Connection Established (14) eap_peap: [eaptls process] = handled (14) eap: Sending EAP Request (code 1) ID 5 length 57 (14) eap: EAP session adding &reply:State = 0x5205bbdd5600a286 (14) [eap] = handled (14) } # authenticate = handled (14) Using Post-Auth-Type Challenge (14) # Executing group from file /etc/raddb/sites-enabled/default (14) Challenge { ... } # empty sub-section is ignored (14) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (14) EAP-Message = 0x0105003919001403030001011603030028122ff0483babe9a32cbc96f0d25bf63a626964a174c6d14dcb7c9b46ce542267b243424249cc2558 (14) Message-Authenticator = 0x00000000000000000000000000000000 (14) State = 0x5205bbdd5600a286e7a44a448065710e (14) Finished request Waking up in 4.9 seconds. (14) Cleaning up request packet ID 0 with timestamp +44 (15) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 149 (15) User-Name = "CLEARSYSTEM\\test1" (15) NAS-IP-Address = 172.22.22.254 (15) Called-Station-Id = "001601dfe596" (15) Calling-Station-Id = "74da38d41a8b" (15) NAS-Identifier = "001601dfe596" (15) NAS-Port = 5 (15) Framed-MTU = 1400 (15) State = 0x5205bbdd5600a286e7a44a448065710e (15) NAS-Port-Type = Wireless-802.11 (15) EAP-Message = 0x020500061900 (15) Message-Authenticator = 0xba0c8dd74427d48a0598d69c4d657f2e (15) session-state: No cached attributes (15) # Executing section authorize from file /etc/raddb/sites-enabled/default (15) authorize { (15) policy filter_username { (15) if (&User-Name) { (15) if (&User-Name) -> TRUE (15) if (&User-Name) { (15) if (&User-Name =~ / /) { (15) if (&User-Name =~ / /) -> FALSE (15) if (&User-Name =~ /@[^@]*@/ ) { (15) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (15) if (&User-Name =~ /\.\./ ) { (15) if (&User-Name =~ /\.\./ ) -> FALSE (15) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (15) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (15) if (&User-Name =~ /\.$/) { (15) if (&User-Name =~ /\.$/) -> FALSE (15) if (&User-Name =~ /(a)\./) { (15) if (&User-Name =~ /(a)\./) -> FALSE (15) } # if (&User-Name) = notfound (15) } # policy filter_username = notfound (15) [preprocess] = ok (15) [chap] = noop (15) [mschap] = noop (15) [digest] = noop (15) suffix: Checking for suffix after "@" (15) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (15) suffix: No such realm "NULL" (15) [suffix] = noop (15) ntdomain: Checking for prefix before "\" (15) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (15) ntdomain: Found realm "CLEARSYSTEM" (15) ntdomain: Adding Stripped-User-Name = "test1" (15) ntdomain: Adding Realm = "CLEARSYSTEM" (15) ntdomain: Authentication realm is LOCAL (15) [ntdomain] = ok (15) eap: Peer sent EAP Response (code 2) ID 5 length 6 (15) eap: Continuing tunnel setup (15) [eap] = ok (15) } # authorize = ok (15) Found Auth-Type = eap (15) # Executing group from file /etc/raddb/sites-enabled/default (15) authenticate { (15) eap: Expiring EAP session with state 0x5205bbdd5600a286 (15) eap: Finished EAP session with state 0x5205bbdd5600a286 (15) eap: Previous EAP request found for state 0x5205bbdd5600a286, released from the list (15) eap: Peer sent packet with method EAP PEAP (25) (15) eap: Calling submodule eap_peap to process data (15) eap_peap: Continuing EAP-TLS (15) eap_peap: Peer ACKed our handshake fragment. handshake is finished (15) eap_peap: [eaptls verify] = success (15) eap_peap: [eaptls process] = success (15) eap_peap: Session established. Decoding tunneled attributes (15) eap_peap: PEAP state TUNNEL ESTABLISHED (15) eap: Sending EAP Request (code 1) ID 6 length 40 (15) eap: EAP session adding &reply:State = 0x5205bbdd5703a286 (15) [eap] = handled (15) } # authenticate = handled (15) Using Post-Auth-Type Challenge (15) # Executing group from file /etc/raddb/sites-enabled/default (15) Challenge { ... } # empty sub-section is ignored (15) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (15) EAP-Message = 0x010600281900170303001d122ff0483babe9a424c759d906f9537f7d767703eec2c038b2f205ea12 (15) Message-Authenticator = 0x00000000000000000000000000000000 (15) State = 0x5205bbdd5703a286e7a44a448065710e (15) Finished request Waking up in 4.9 seconds. (15) Cleaning up request packet ID 0 with timestamp +44 (16) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 196 (16) User-Name = "CLEARSYSTEM\\test1" (16) NAS-IP-Address = 172.22.22.254 (16) Called-Station-Id = "001601dfe596" (16) Calling-Station-Id = "74da38d41a8b" (16) NAS-Identifier = "001601dfe596" (16) NAS-Port = 5 (16) Framed-MTU = 1400 (16) State = 0x5205bbdd5703a286e7a44a448065710e (16) NAS-Port-Type = Wireless-802.11 (16) EAP-Message = 0x020600351900170303002a0000000000000001e9ae658790bcf508c51af80646d2e96dbcf95fbb80c7aa0688d889cbd19217068129 (16) Message-Authenticator = 0x8a30e51d727a26dfab63163b3eca1458 (16) session-state: No cached attributes (16) # Executing section authorize from file /etc/raddb/sites-enabled/default (16) authorize { (16) policy filter_username { (16) if (&User-Name) { (16) if (&User-Name) -> TRUE (16) if (&User-Name) { (16) if (&User-Name =~ / /) { (16) if (&User-Name =~ / /) -> FALSE (16) if (&User-Name =~ /@[^@]*@/ ) { (16) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (16) if (&User-Name =~ /\.\./ ) { (16) if (&User-Name =~ /\.\./ ) -> FALSE (16) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (16) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (16) if (&User-Name =~ /\.$/) { (16) if (&User-Name =~ /\.$/) -> FALSE (16) if (&User-Name =~ /(a)\./) { (16) if (&User-Name =~ /(a)\./) -> FALSE (16) } # if (&User-Name) = notfound (16) } # policy filter_username = notfound (16) [preprocess] = ok (16) [chap] = noop (16) [mschap] = noop (16) [digest] = noop (16) suffix: Checking for suffix after "@" (16) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (16) suffix: No such realm "NULL" (16) [suffix] = noop (16) ntdomain: Checking for prefix before "\" (16) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (16) ntdomain: Found realm "CLEARSYSTEM" (16) ntdomain: Adding Stripped-User-Name = "test1" (16) ntdomain: Adding Realm = "CLEARSYSTEM" (16) ntdomain: Authentication realm is LOCAL (16) [ntdomain] = ok (16) eap: Peer sent EAP Response (code 2) ID 6 length 53 (16) eap: Continuing tunnel setup (16) [eap] = ok (16) } # authorize = ok (16) Found Auth-Type = eap (16) # Executing group from file /etc/raddb/sites-enabled/default (16) authenticate { (16) eap: Expiring EAP session with state 0x5205bbdd5703a286 (16) eap: Finished EAP session with state 0x5205bbdd5703a286 (16) eap: Previous EAP request found for state 0x5205bbdd5703a286, released from the list (16) eap: Peer sent packet with method EAP PEAP (25) (16) eap: Calling submodule eap_peap to process data (16) eap_peap: Continuing EAP-TLS (16) eap_peap: [eaptls verify] = ok (16) eap_peap: Done initial handshake (16) eap_peap: [eaptls process] = ok (16) eap_peap: Session established. Decoding tunneled attributes (16) eap_peap: PEAP state WAITING FOR INNER IDENTITY (16) eap_peap: Identity - CLEARSYSTEM\test1 (16) eap_peap: Got inner identity 'CLEARSYSTEM\test1' (16) eap_peap: Setting default EAP type for tunneled EAP session (16) eap_peap: Got tunneled request (16) eap_peap: EAP-Message = 0x0206001601434c45415253595354454d5c7465737431 (16) eap_peap: Setting User-Name to CLEARSYSTEM\test1 (16) eap_peap: Sending tunneled request to inner-tunnel (16) eap_peap: EAP-Message = 0x0206001601434c45415253595354454d5c7465737431 (16) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1 (16) eap_peap: User-Name = "CLEARSYSTEM\\test1" (16) Virtual server inner-tunnel received request (16) EAP-Message = 0x0206001601434c45415253595354454d5c7465737431 (16) FreeRADIUS-Proxied-To = 127.0.0.1 (16) User-Name = "CLEARSYSTEM\\test1" (16) WARNING: Outer and inner identities are the same. User privacy is compromised. (16) server inner-tunnel { (16) # Executing section authorize from file /etc/raddb/sites-enabled/inner-tunnel (16) authorize { (16) policy filter_username { (16) if (&User-Name) { (16) if (&User-Name) -> TRUE (16) if (&User-Name) { (16) if (&User-Name =~ / /) { (16) if (&User-Name =~ / /) -> FALSE (16) if (&User-Name =~ /@[^@]*@/ ) { (16) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (16) if (&User-Name =~ /\.\./ ) { (16) if (&User-Name =~ /\.\./ ) -> FALSE (16) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (16) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (16) if (&User-Name =~ /\.$/) { (16) if (&User-Name =~ /\.$/) -> FALSE (16) if (&User-Name =~ /(a)\./) { (16) if (&User-Name =~ /(a)\./) -> FALSE (16) } # if (&User-Name) = notfound (16) } # policy filter_username = notfound (16) [chap] = noop (16) [mschap] = noop (16) suffix: Checking for suffix after "@" (16) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (16) suffix: No such realm "NULL" (16) [suffix] = noop (16) ntdomain: Checking for prefix before "\" (16) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (16) ntdomain: Found realm "CLEARSYSTEM" (16) ntdomain: Adding Stripped-User-Name = "test1" (16) ntdomain: Adding Realm = "CLEARSYSTEM" (16) ntdomain: Authentication realm is LOCAL (16) [ntdomain] = ok (16) update control { (16) &Proxy-To-Realm := LOCAL (16) } # update control = noop (16) eap: Peer sent EAP Response (code 2) ID 6 length 22 (16) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize (16) [eap] = ok (16) } # authorize = ok (16) Found Auth-Type = eap (16) # Executing group from file /etc/raddb/sites-enabled/inner-tunnel (16) authenticate { (16) eap: Peer sent packet with method EAP Identity (1) (16) eap: Calling submodule eap_mschapv2 to process data (16) eap_mschapv2: Issuing Challenge (16) eap: Sending EAP Request (code 1) ID 7 length 43 (16) eap: EAP session adding &reply:State = 0x9f2abfcb9f2da540 (16) [eap] = handled (16) } # authenticate = handled (16) } # server inner-tunnel (16) Virtual server sending reply (16) EAP-Message = 0x0107002b1a0107002610ab071fbb0514782fb1bda2c0ac5e09c8667265657261646975732d332e302e3133 (16) Message-Authenticator = 0x00000000000000000000000000000000 (16) State = 0x9f2abfcb9f2da540a6c3ea21abac845a (16) eap_peap: Got tunneled reply code 11 (16) eap_peap: EAP-Message = 0x0107002b1a0107002610ab071fbb0514782fb1bda2c0ac5e09c8667265657261646975732d332e302e3133 (16) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (16) eap_peap: State = 0x9f2abfcb9f2da540a6c3ea21abac845a (16) eap_peap: Got tunneled reply RADIUS code 11 (16) eap_peap: EAP-Message = 0x0107002b1a0107002610ab071fbb0514782fb1bda2c0ac5e09c8667265657261646975732d332e302e3133 (16) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (16) eap_peap: State = 0x9f2abfcb9f2da540a6c3ea21abac845a (16) eap_peap: Got tunneled Access-Challenge (16) eap: Sending EAP Request (code 1) ID 7 length 74 (16) eap: EAP session adding &reply:State = 0x5205bbdd5402a286 (16) [eap] = handled (16) } # authenticate = handled (16) Using Post-Auth-Type Challenge (16) # Executing group from file /etc/raddb/sites-enabled/default (16) Challenge { ... } # empty sub-section is ignored (16) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (16) EAP-Message = 0x0107004a1900170303003f122ff0483babe9a513b02ec03d204efc57ab871b548e72aafff7ba98622273aa90a11010b9660956f197a045a87b30441d1c1d85195860ad5064611ed769d7 (16) Message-Authenticator = 0x00000000000000000000000000000000 (16) State = 0x5205bbdd5402a286e7a44a448065710e (16) Finished request Waking up in 4.9 seconds. (16) Cleaning up request packet ID 0 with timestamp +44 (17) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 250 (17) User-Name = "CLEARSYSTEM\\test1" (17) NAS-IP-Address = 172.22.22.254 (17) Called-Station-Id = "001601dfe596" (17) Calling-Station-Id = "74da38d41a8b" (17) NAS-Identifier = "001601dfe596" (17) NAS-Port = 5 (17) Framed-MTU = 1400 (17) State = 0x5205bbdd5402a286e7a44a448065710e (17) NAS-Port-Type = Wireless-802.11 (17) EAP-Message = 0x0207006b19001703030060000000000000000299fb53660f3339f803de24143aaa136dbbe1675bac64891edc1ae768085758bb81158d747f11b403c48bc4e5b936060a7a609a8ab04e3a89cc6b3c728d192b3da65f61401398db953f4170997389c9f34d07821ddde226e3 (17) Message-Authenticator = 0xfa99de92a4eace1085df9e301e533682 (17) session-state: No cached attributes (17) # Executing section authorize from file /etc/raddb/sites-enabled/default (17) authorize { (17) policy filter_username { (17) if (&User-Name) { (17) if (&User-Name) -> TRUE (17) if (&User-Name) { (17) if (&User-Name =~ / /) { (17) if (&User-Name =~ / /) -> FALSE (17) if (&User-Name =~ /@[^@]*@/ ) { (17) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (17) if (&User-Name =~ /\.\./ ) { (17) if (&User-Name =~ /\.\./ ) -> FALSE (17) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (17) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (17) if (&User-Name =~ /\.$/) { (17) if (&User-Name =~ /\.$/) -> FALSE (17) if (&User-Name =~ /(a)\./) { (17) if (&User-Name =~ /(a)\./) -> FALSE (17) } # if (&User-Name) = notfound (17) } # policy filter_username = notfound (17) [preprocess] = ok (17) [chap] = noop (17) [mschap] = noop (17) [digest] = noop (17) suffix: Checking for suffix after "@" (17) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (17) suffix: No such realm "NULL" (17) [suffix] = noop (17) ntdomain: Checking for prefix before "\" (17) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (17) ntdomain: Found realm "CLEARSYSTEM" (17) ntdomain: Adding Stripped-User-Name = "test1" (17) ntdomain: Adding Realm = "CLEARSYSTEM" (17) ntdomain: Authentication realm is LOCAL (17) [ntdomain] = ok (17) eap: Peer sent EAP Response (code 2) ID 7 length 107 (17) eap: Continuing tunnel setup (17) [eap] = ok (17) } # authorize = ok (17) Found Auth-Type = eap (17) # Executing group from file /etc/raddb/sites-enabled/default (17) authenticate { (17) eap: Expiring EAP session with state 0x9f2abfcb9f2da540 (17) eap: Finished EAP session with state 0x5205bbdd5402a286 (17) eap: Previous EAP request found for state 0x5205bbdd5402a286, released from the list (17) eap: Peer sent packet with method EAP PEAP (25) (17) eap: Calling submodule eap_peap to process data (17) eap_peap: Continuing EAP-TLS (17) eap_peap: [eaptls verify] = ok (17) eap_peap: Done initial handshake (17) eap_peap: [eaptls process] = ok (17) eap_peap: Session established. Decoding tunneled attributes (17) eap_peap: PEAP state phase2 (17) eap_peap: EAP method MSCHAPv2 (26) (17) eap_peap: Got tunneled request (17) eap_peap: EAP-Message = 0x0207004c1a020700473158997abcf14dc72e0ca245a5dee28d1900000000000000006ae124b20068086b3497643a4966950e331dae11243fcd6f00434c45415253595354454d5c7465737431 (17) eap_peap: Setting User-Name to CLEARSYSTEM\test1 (17) eap_peap: Sending tunneled request to inner-tunnel (17) eap_peap: EAP-Message = 0x0207004c1a020700473158997abcf14dc72e0ca245a5dee28d1900000000000000006ae124b20068086b3497643a4966950e331dae11243fcd6f00434c45415253595354454d5c7465737431 (17) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1 (17) eap_peap: User-Name = "CLEARSYSTEM\\test1" (17) eap_peap: State = 0x9f2abfcb9f2da540a6c3ea21abac845a (17) Virtual server inner-tunnel received request (17) EAP-Message = 0x0207004c1a020700473158997abcf14dc72e0ca245a5dee28d1900000000000000006ae124b20068086b3497643a4966950e331dae11243fcd6f00434c45415253595354454d5c7465737431 (17) FreeRADIUS-Proxied-To = 127.0.0.1 (17) User-Name = "CLEARSYSTEM\\test1" (17) State = 0x9f2abfcb9f2da540a6c3ea21abac845a (17) WARNING: Outer and inner identities are the same. User privacy is compromised. (17) server inner-tunnel { (17) session-state: No cached attributes (17) # Executing section authorize from file /etc/raddb/sites-enabled/inner-tunnel (17) authorize { (17) policy filter_username { (17) if (&User-Name) { (17) if (&User-Name) -> TRUE (17) if (&User-Name) { (17) if (&User-Name =~ / /) { (17) if (&User-Name =~ / /) -> FALSE (17) if (&User-Name =~ /@[^@]*@/ ) { (17) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (17) if (&User-Name =~ /\.\./ ) { (17) if (&User-Name =~ /\.\./ ) -> FALSE (17) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (17) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (17) if (&User-Name =~ /\.$/) { (17) if (&User-Name =~ /\.$/) -> FALSE (17) if (&User-Name =~ /(a)\./) { (17) if (&User-Name =~ /(a)\./) -> FALSE (17) } # if (&User-Name) = notfound (17) } # policy filter_username = notfound (17) [chap] = noop (17) [mschap] = noop (17) suffix: Checking for suffix after "@" (17) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (17) suffix: No such realm "NULL" (17) [suffix] = noop (17) ntdomain: Checking for prefix before "\" (17) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (17) ntdomain: Found realm "CLEARSYSTEM" (17) ntdomain: Adding Stripped-User-Name = "test1" (17) ntdomain: Adding Realm = "CLEARSYSTEM" (17) ntdomain: Authentication realm is LOCAL (17) [ntdomain] = ok (17) update control { (17) &Proxy-To-Realm := LOCAL (17) } # update control = noop (17) eap: Peer sent EAP Response (code 2) ID 7 length 76 (17) eap: No EAP Start, assuming it's an on-going EAP conversation (17) [eap] = updated (17) files: Searching for user in group "allusers" rlm_ldap (ldap): Reserved connection (4) (17) files: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (17) files: --> (uid=test1) (17) files: Performing search in "dc=system,dc=lan" with filter "(uid=test1)", scope "sub" (17) files: Waiting for search result... (17) files: User object found at DN "cn=test1 test1,ou=Users,ou=Accounts,dc=system,dc=lan" (17) files: Checking user object's memberOf attributes (17) files: Performing unfiltered search in "cn=test1 test1,ou=Users,ou=Accounts,dc=system,dc=lan", scope "base" (17) files: Waiting for search result... (17) files: Processing memberOf value "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (17) files: Resolving group DN "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (17) files: Performing unfiltered search in "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (17) files: Waiting for search result... (17) files: Group DN "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "ftp_plugin" (17) files: Processing memberOf value "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (17) files: Resolving group DN "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (17) files: Performing unfiltered search in "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (17) files: Waiting for search result... (17) files: Group DN "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "web_proxy_plugin" (17) files: Processing memberOf value "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (17) files: Resolving group DN "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (17) files: Performing unfiltered search in "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (17) files: Waiting for search result... (17) files: Group DN "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "webupload" (17) files: Processing memberOf value "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (17) files: Resolving group DN "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (17) files: Performing unfiltered search in "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (17) files: Waiting for search result... (17) files: Group DN "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "allusers" (17) files: User found in group "allusers". Comparison between membership: name (resolved from DN "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan"), check: name rlm_ldap (ldap): Released connection (4) rlm_ldap (ldap): Closing connection (0), from 1 unused connections (17) [files] = noop rlm_ldap (ldap): Reserved connection (1) (17) ldap: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (17) ldap: --> (uid=test1) (17) ldap: Performing search in "dc=system,dc=lan" with filter "(uid=test1)", scope "sub" (17) ldap: Waiting for search result... (17) ldap: User object found at DN "cn=test1 test1,ou=Users,ou=Accounts,dc=system,dc=lan" (17) ldap: Processing user attributes (17) ldap: control:Password-With-Header += '{sha}tESsBmE/yNY3lb6a0L6vVQEZNqw=' rlm_ldap (ldap): Released connection (1) (17) [ldap] = updated (17) [expiration] = noop (17) [logintime] = noop (17) pap: Converted: &control:Password-With-Header -> &control:SHA1-Password (17) pap: Removing &control:Password-With-Header (17) pap: Normalizing SHA1-Password from base64 encoding, 28 bytes -> 20 bytes (17) pap: WARNING: Auth-Type already set. Not setting to PAP (17) [pap] = noop (17) } # authorize = updated (17) Found Auth-Type = eap (17) # Executing group from file /etc/raddb/sites-enabled/inner-tunnel (17) authenticate { (17) eap: Expiring EAP session with state 0x9f2abfcb9f2da540 (17) eap: Finished EAP session with state 0x9f2abfcb9f2da540 (17) eap: Previous EAP request found for state 0x9f2abfcb9f2da540, released from the list (17) eap: Peer sent packet with method EAP MSCHAPv2 (26) (17) eap: Calling submodule eap_mschapv2 to process data (17) eap_mschapv2: # Executing group from file /etc/raddb/sites-enabled/inner-tunnel (17) eap_mschapv2: authenticate { (17) mschap: Creating challenge hash with username: test1 (17) mschap: Client is using MS-CHAPv2 (17) mschap: Executing: /usr/bin/ntlm_auth --request-nt-key --username=%{%{Stripped-User-Name}:-%{%{User-Name}:-None}} --challenge=%{%{mschap:Challenge}:-00} --nt-response=%{%{mschap:NT-Response}:-00}: (17) mschap: EXPAND --username=%{%{Stripped-User-Name}:-%{%{User-Name}:-None}} (17) mschap: --> --username=test1 (17) mschap: Creating challenge hash with username: test1 (17) mschap: EXPAND --challenge=%{%{mschap:Challenge}:-00} (17) mschap: --> --challenge=259875cdeba4749e (17) mschap: EXPAND --nt-response=%{%{mschap:NT-Response}:-00} (17) mschap: --> --nt-response=6ae124b20068086b3497643a4966950e331dae11243fcd6f (17) mschap: Program returned code (0) and output 'NT_KEY: DAE53F1776DBD0817C5639A27629A27D' (17) mschap: Adding MS-CHAPv2 MPPE keys (17) [mschap] = ok (17) } # authenticate = ok (17) MSCHAP Success (17) eap: Sending EAP Request (code 1) ID 8 length 51 (17) eap: EAP session adding &reply:State = 0x9f2abfcb9e22a540 (17) [eap] = handled (17) } # authenticate = handled (17) } # server inner-tunnel (17) Virtual server sending reply (17) EAP-Message = 0x010800331a0307002e533d34453836303736424638434130354230383244423136383334433839364133464331464146343135 (17) Message-Authenticator = 0x00000000000000000000000000000000 (17) State = 0x9f2abfcb9e22a540a6c3ea21abac845a (17) eap_peap: Got tunneled reply code 11 (17) eap_peap: EAP-Message = 0x010800331a0307002e533d34453836303736424638434130354230383244423136383334433839364133464331464146343135 (17) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (17) eap_peap: State = 0x9f2abfcb9e22a540a6c3ea21abac845a (17) eap_peap: Got tunneled reply RADIUS code 11 (17) eap_peap: EAP-Message = 0x010800331a0307002e533d34453836303736424638434130354230383244423136383334433839364133464331464146343135 (17) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (17) eap_peap: State = 0x9f2abfcb9e22a540a6c3ea21abac845a (17) eap_peap: Got tunneled Access-Challenge (17) eap: Sending EAP Request (code 1) ID 8 length 82 (17) eap: EAP session adding &reply:State = 0x5205bbdd550da286 (17) [eap] = handled (17) } # authenticate = handled (17) Using Post-Auth-Type Challenge (17) # Executing group from file /etc/raddb/sites-enabled/default (17) Challenge { ... } # empty sub-section is ignored (17) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (17) EAP-Message = 0x0108005219001703030047122ff0483babe9a629ef7e39c3646169247fd488b6a98ca283175ebbc1280cb371a00156e2a8b26a3a7c4757c476af1fecdda2a199fe60a6cc1e085515cc6af0acbed0445bea81 (17) Message-Authenticator = 0x00000000000000000000000000000000 (17) State = 0x5205bbdd550da286e7a44a448065710e (17) Finished request Waking up in 4.9 seconds. (17) Cleaning up request packet ID 0 with timestamp +44 (18) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 180 (18) User-Name = "CLEARSYSTEM\\test1" (18) NAS-IP-Address = 172.22.22.254 (18) Called-Station-Id = "001601dfe596" (18) Calling-Station-Id = "74da38d41a8b" (18) NAS-Identifier = "001601dfe596" (18) NAS-Port = 5 (18) Framed-MTU = 1400 (18) State = 0x5205bbdd550da286e7a44a448065710e (18) NAS-Port-Type = Wireless-802.11 (18) EAP-Message = 0x020800251900170303001a0000000000000003ca0270723e03845843b2cb34cebae8dbe894 (18) Message-Authenticator = 0xa3f3022ca15ddf63716794674aad60fe (18) session-state: No cached attributes (18) # Executing section authorize from file /etc/raddb/sites-enabled/default (18) authorize { (18) policy filter_username { (18) if (&User-Name) { (18) if (&User-Name) -> TRUE (18) if (&User-Name) { (18) if (&User-Name =~ / /) { (18) if (&User-Name =~ / /) -> FALSE (18) if (&User-Name =~ /@[^@]*@/ ) { (18) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (18) if (&User-Name =~ /\.\./ ) { (18) if (&User-Name =~ /\.\./ ) -> FALSE (18) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (18) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (18) if (&User-Name =~ /\.$/) { (18) if (&User-Name =~ /\.$/) -> FALSE (18) if (&User-Name =~ /(a)\./) { (18) if (&User-Name =~ /(a)\./) -> FALSE (18) } # if (&User-Name) = notfound (18) } # policy filter_username = notfound (18) [preprocess] = ok (18) [chap] = noop (18) [mschap] = noop (18) [digest] = noop (18) suffix: Checking for suffix after "@" (18) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (18) suffix: No such realm "NULL" (18) [suffix] = noop (18) ntdomain: Checking for prefix before "\" (18) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (18) ntdomain: Found realm "CLEARSYSTEM" (18) ntdomain: Adding Stripped-User-Name = "test1" (18) ntdomain: Adding Realm = "CLEARSYSTEM" (18) ntdomain: Authentication realm is LOCAL (18) [ntdomain] = ok (18) eap: Peer sent EAP Response (code 2) ID 8 length 37 (18) eap: Continuing tunnel setup (18) [eap] = ok (18) } # authorize = ok (18) Found Auth-Type = eap (18) # Executing group from file /etc/raddb/sites-enabled/default (18) authenticate { (18) eap: Expiring EAP session with state 0x9f2abfcb9e22a540 (18) eap: Finished EAP session with state 0x5205bbdd550da286 (18) eap: Previous EAP request found for state 0x5205bbdd550da286, released from the list (18) eap: Peer sent packet with method EAP PEAP (25) (18) eap: Calling submodule eap_peap to process data (18) eap_peap: Continuing EAP-TLS (18) eap_peap: [eaptls verify] = ok (18) eap_peap: Done initial handshake (18) eap_peap: [eaptls process] = ok (18) eap_peap: Session established. Decoding tunneled attributes (18) eap_peap: PEAP state phase2 (18) eap_peap: EAP method MSCHAPv2 (26) (18) eap_peap: Got tunneled request (18) eap_peap: EAP-Message = 0x020800061a03 (18) eap_peap: Setting User-Name to CLEARSYSTEM\test1 (18) eap_peap: Sending tunneled request to inner-tunnel (18) eap_peap: EAP-Message = 0x020800061a03 (18) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1 (18) eap_peap: User-Name = "CLEARSYSTEM\\test1" (18) eap_peap: State = 0x9f2abfcb9e22a540a6c3ea21abac845a (18) Virtual server inner-tunnel received request (18) EAP-Message = 0x020800061a03 (18) FreeRADIUS-Proxied-To = 127.0.0.1 (18) User-Name = "CLEARSYSTEM\\test1" (18) State = 0x9f2abfcb9e22a540a6c3ea21abac845a (18) WARNING: Outer and inner identities are the same. User privacy is compromised. (18) server inner-tunnel { (18) session-state: No cached attributes (18) # Executing section authorize from file /etc/raddb/sites-enabled/inner-tunnel (18) authorize { (18) policy filter_username { (18) if (&User-Name) { (18) if (&User-Name) -> TRUE (18) if (&User-Name) { (18) if (&User-Name =~ / /) { (18) if (&User-Name =~ / /) -> FALSE (18) if (&User-Name =~ /@[^@]*@/ ) { (18) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (18) if (&User-Name =~ /\.\./ ) { (18) if (&User-Name =~ /\.\./ ) -> FALSE (18) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (18) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (18) if (&User-Name =~ /\.$/) { (18) if (&User-Name =~ /\.$/) -> FALSE (18) if (&User-Name =~ /(a)\./) { (18) if (&User-Name =~ /(a)\./) -> FALSE (18) } # if (&User-Name) = notfound (18) } # policy filter_username = notfound (18) [chap] = noop (18) [mschap] = noop (18) suffix: Checking for suffix after "@" (18) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (18) suffix: No such realm "NULL" (18) [suffix] = noop (18) ntdomain: Checking for prefix before "\" (18) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (18) ntdomain: Found realm "CLEARSYSTEM" (18) ntdomain: Adding Stripped-User-Name = "test1" (18) ntdomain: Adding Realm = "CLEARSYSTEM" (18) ntdomain: Authentication realm is LOCAL (18) [ntdomain] = ok (18) update control { (18) &Proxy-To-Realm := LOCAL (18) } # update control = noop (18) eap: Peer sent EAP Response (code 2) ID 8 length 6 (18) eap: No EAP Start, assuming it's an on-going EAP conversation (18) [eap] = updated (18) files: Searching for user in group "allusers" rlm_ldap (ldap): Reserved connection (2) (18) files: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (18) files: --> (uid=test1) (18) files: Performing search in "dc=system,dc=lan" with filter "(uid=test1)", scope "sub" (18) files: Waiting for search result... (18) files: User object found at DN "cn=test1 test1,ou=Users,ou=Accounts,dc=system,dc=lan" (18) files: Checking user object's memberOf attributes (18) files: Performing unfiltered search in "cn=test1 test1,ou=Users,ou=Accounts,dc=system,dc=lan", scope "base" (18) files: Waiting for search result... (18) files: Processing memberOf value "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (18) files: Resolving group DN "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (18) files: Performing unfiltered search in "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (18) files: Waiting for search result... (18) files: Group DN "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "ftp_plugin" (18) files: Processing memberOf value "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (18) files: Resolving group DN "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (18) files: Performing unfiltered search in "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (18) files: Waiting for search result... (18) files: Group DN "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "web_proxy_plugin" (18) files: Processing memberOf value "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (18) files: Resolving group DN "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (18) files: Performing unfiltered search in "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (18) files: Waiting for search result... (18) files: Group DN "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "webupload" (18) files: Processing memberOf value "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (18) files: Resolving group DN "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (18) files: Performing unfiltered search in "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (18) files: Waiting for search result... (18) files: Group DN "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "allusers" (18) files: User found in group "allusers". Comparison between membership: name (resolved from DN "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=l?"), check: name rlm_ldap (ldap): Released connection (2) (18) [files] = noop rlm_ldap (ldap): Reserved connection (3) (18) ldap: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (18) ldap: --> (uid=test1) (18) ldap: Performing search in "dc=system,dc=lan" with filter "(uid=test1)", scope "sub" (18) ldap: Waiting for search result... (18) ldap: User object found at DN "cn=test1 test1,ou=Users,ou=Accounts,dc=system,dc=lan" (18) ldap: Processing user attributes (18) ldap: control:Password-With-Header += '{sha}tESsBmE/yNY3lb6a0L6vVQEZNqw=' rlm_ldap (ldap): Released connection (3) (18) [ldap] = updated (18) [expiration] = noop (18) [logintime] = noop (18) pap: Converted: &control:Password-With-Header -> &control:SHA1-Password (18) pap: Removing &control:Password-With-Header (18) pap: Normalizing SHA1-Password from base64 encoding, 28 bytes -> 20 bytes (18) pap: WARNING: Auth-Type already set. Not setting to PAP (18) [pap] = noop (18) } # authorize = updated (18) Found Auth-Type = eap (18) # Executing group from file /etc/raddb/sites-enabled/inner-tunnel (18) authenticate { (18) eap: Expiring EAP session with state 0x9f2abfcb9e22a540 (18) eap: Finished EAP session with state 0x9f2abfcb9e22a540 (18) eap: Previous EAP request found for state 0x9f2abfcb9e22a540, released from the list (18) eap: Peer sent packet with method EAP MSCHAPv2 (26) (18) eap: Calling submodule eap_mschapv2 to process data (18) eap: Sending EAP Success (code 3) ID 8 length 4 (18) eap: Freeing handler (18) [eap] = ok (18) } # authenticate = ok (18) # Executing section post-auth from file /etc/raddb/sites-enabled/inner-tunnel (18) post-auth { (18) if (0) { (18) if (0) -> FALSE (18) } # post-auth = noop (18) } # server inner-tunnel (18) Virtual server sending reply (18) MS-MPPE-Encryption-Policy = Encryption-Allowed (18) MS-MPPE-Encryption-Types = RC4-40or128-bit-Allowed (18) MS-MPPE-Send-Key = 0x9f37c0e1d4ae81eaea7ac004f3bb5134 (18) MS-MPPE-Recv-Key = 0x8f50bbb6f8efe9070c7af89a4d834531 (18) EAP-Message = 0x03080004 (18) Message-Authenticator = 0x00000000000000000000000000000000 (18) Stripped-User-Name = "test1" (18) eap_peap: Got tunneled reply code 2 (18) eap_peap: MS-MPPE-Encryption-Policy = Encryption-Allowed (18) eap_peap: MS-MPPE-Encryption-Types = RC4-40or128-bit-Allowed (18) eap_peap: MS-MPPE-Send-Key = 0x9f37c0e1d4ae81eaea7ac004f3bb5134 (18) eap_peap: MS-MPPE-Recv-Key = 0x8f50bbb6f8efe9070c7af89a4d834531 (18) eap_peap: EAP-Message = 0x03080004 (18) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (18) eap_peap: Stripped-User-Name = "test1" (18) eap_peap: Got tunneled reply RADIUS code 2 (18) eap_peap: MS-MPPE-Encryption-Policy = Encryption-Allowed (18) eap_peap: MS-MPPE-Encryption-Types = RC4-40or128-bit-Allowed (18) eap_peap: MS-MPPE-Send-Key = 0x9f37c0e1d4ae81eaea7ac004f3bb5134 (18) eap_peap: MS-MPPE-Recv-Key = 0x8f50bbb6f8efe9070c7af89a4d834531 (18) eap_peap: EAP-Message = 0x03080004 (18) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (18) eap_peap: Stripped-User-Name = "test1" (18) eap_peap: Tunneled authentication was successful (18) eap_peap: SUCCESS (18) eap: Sending EAP Request (code 1) ID 9 length 46 (18) eap: EAP session adding &reply:State = 0x5205bbdd5a0ca286 (18) [eap] = handled (18) } # authenticate = handled (18) Using Post-Auth-Type Challenge (18) # Executing group from file /etc/raddb/sites-enabled/default (18) Challenge { ... } # empty sub-section is ignored (18) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (18) EAP-Message = 0x0109002e19001703030023122ff0483babe9a792158bc6ad78757a858837b878ce0bc7a162c340720b68c2f14dff (18) Message-Authenticator = 0x00000000000000000000000000000000 (18) State = 0x5205bbdd5a0ca286e7a44a448065710e (18) Finished request Waking up in 4.9 seconds. (18) Cleaning up request packet ID 0 with timestamp +44 (19) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 189 (19) User-Name = "CLEARSYSTEM\\test1" (19) NAS-IP-Address = 172.22.22.254 (19) Called-Station-Id = "001601dfe596" (19) Calling-Station-Id = "74da38d41a8b" (19) NAS-Identifier = "001601dfe596" (19) NAS-Port = 5 (19) Framed-MTU = 1400 (19) State = 0x5205bbdd5a0ca286e7a44a448065710e (19) NAS-Port-Type = Wireless-802.11 (19) EAP-Message = 0x0209002e190017030300230000000000000004b670ecb66f45a52089029ef2d2526cd88f998a49f04e0a33532b8f (19) Message-Authenticator = 0x1547e8623f812242aa168cffa15b4bf4 (19) session-state: No cached attributes (19) # Executing section authorize from file /etc/raddb/sites-enabled/default (19) authorize { (19) policy filter_username { (19) if (&User-Name) { (19) if (&User-Name) -> TRUE (19) if (&User-Name) { (19) if (&User-Name =~ / /) { (19) if (&User-Name =~ / /) -> FALSE (19) if (&User-Name =~ /@[^@]*@/ ) { (19) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (19) if (&User-Name =~ /\.\./ ) { (19) if (&User-Name =~ /\.\./ ) -> FALSE (19) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (19) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (19) if (&User-Name =~ /\.$/) { (19) if (&User-Name =~ /\.$/) -> FALSE (19) if (&User-Name =~ /(a)\./) { (19) if (&User-Name =~ /(a)\./) -> FALSE (19) } # if (&User-Name) = notfound (19) } # policy filter_username = notfound (19) [preprocess] = ok (19) [chap] = noop (19) [mschap] = noop (19) [digest] = noop (19) suffix: Checking for suffix after "@" (19) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (19) suffix: No such realm "NULL" (19) [suffix] = noop (19) ntdomain: Checking for prefix before "\" (19) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (19) ntdomain: Found realm "CLEARSYSTEM" (19) ntdomain: Adding Stripped-User-Name = "test1" (19) ntdomain: Adding Realm = "CLEARSYSTEM" (19) ntdomain: Authentication realm is LOCAL (19) [ntdomain] = ok (19) eap: Peer sent EAP Response (code 2) ID 9 length 46 (19) eap: Continuing tunnel setup (19) [eap] = ok (19) } # authorize = ok (19) Found Auth-Type = eap (19) # Executing group from file /etc/raddb/sites-enabled/default (19) authenticate { (19) eap: Expiring EAP session with state 0x5205bbdd5a0ca286 (19) eap: Finished EAP session with state 0x5205bbdd5a0ca286 (19) eap: Previous EAP request found for state 0x5205bbdd5a0ca286, released from the list (19) eap: Peer sent packet with method EAP PEAP (25) (19) eap: Calling submodule eap_peap to process data (19) eap_peap: Continuing EAP-TLS (19) eap_peap: [eaptls verify] = ok (19) eap_peap: Done initial handshake (19) eap_peap: [eaptls process] = ok (19) eap_peap: Session established. Decoding tunneled attributes (19) eap_peap: PEAP state send tlv success (19) eap_peap: Received EAP-TLV response (19) eap_peap: Success (19) eap: Sending EAP Success (code 3) ID 9 length 4 (19) eap: Freeing handler (19) [eap] = ok (19) } # authenticate = ok (19) # Executing section post-auth from file /etc/raddb/sites-enabled/default (19) post-auth { (19) update { (19) No attributes updated (19) } # update = noop (19) [exec] = noop (19) policy remove_reply_message_if_eap { (19) if (&reply:EAP-Message && &reply:Reply-Message) { (19) if (&reply:EAP-Message && &reply:Reply-Message) -> FALSE (19) else { (19) [noop] = noop (19) } # else = noop (19) } # policy remove_reply_message_if_eap = noop (19) } # post-auth = noop (19) Sent Access-Accept Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (19) MS-MPPE-Recv-Key = 0x2a974e72a8e47133de5164a69bcadf7e50cb5b8e597302ea8864926ace2ad5fa (19) MS-MPPE-Send-Key = 0xa82102166fbb9ded233362e3ee602ba3dc3e63538e8cf48d2a1db1c6eb7fe9b6 (19) EAP-Message = 0x03090004 (19) Message-Authenticator = 0x00000000000000000000000000000000 (19) Finished request Waking up in 4.9 seconds. (19) Cleaning up request packet ID 0 with timestamp +44 Ready to process requests (20) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 147 (20) User-Name = "CLEARSYSTEM\\test1" (20) NAS-IP-Address = 172.22.22.254 (20) Called-Station-Id = "001601dfe596" (20) Calling-Station-Id = "74da38d41a8b" (20) NAS-Identifier = "001601dfe596" (20) NAS-Port = 5 (20) Framed-MTU = 1400 (20) NAS-Port-Type = Wireless-802.11 (20) EAP-Message = 0x0200001601434c45415253595354454d5c7465737431 (20) Message-Authenticator = 0x9933ba7d639c9f63e9cb320a8b41e98f (20) # Executing section authorize from file /etc/raddb/sites-enabled/default (20) authorize { (20) policy filter_username { (20) if (&User-Name) { (20) if (&User-Name) -> TRUE (20) if (&User-Name) { (20) if (&User-Name =~ / /) { (20) if (&User-Name =~ / /) -> FALSE (20) if (&User-Name =~ /@[^@]*@/ ) { (20) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (20) if (&User-Name =~ /\.\./ ) { (20) if (&User-Name =~ /\.\./ ) -> FALSE (20) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (20) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (20) if (&User-Name =~ /\.$/) { (20) if (&User-Name =~ /\.$/) -> FALSE (20) if (&User-Name =~ /(a)\./) { (20) if (&User-Name =~ /(a)\./) -> FALSE (20) } # if (&User-Name) = notfound (20) } # policy filter_username = notfound (20) [preprocess] = ok (20) [chap] = noop (20) [mschap] = noop (20) [digest] = noop (20) suffix: Checking for suffix after "@" (20) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (20) suffix: No such realm "NULL" (20) [suffix] = noop (20) ntdomain: Checking for prefix before "\" (20) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (20) ntdomain: Found realm "CLEARSYSTEM" (20) ntdomain: Adding Stripped-User-Name = "test1" (20) ntdomain: Adding Realm = "CLEARSYSTEM" (20) ntdomain: Authentication realm is LOCAL (20) [ntdomain] = ok (20) eap: Peer sent EAP Response (code 2) ID 0 length 22 (20) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize (20) [eap] = ok (20) } # authorize = ok (20) Found Auth-Type = eap (20) # Executing group from file /etc/raddb/sites-enabled/default (20) authenticate { (20) eap: Peer sent packet with method EAP Identity (1) (20) eap: Calling submodule eap_peap to process data (20) eap_peap: Initiating new EAP-TLS session (20) eap_peap: [eaptls start] = request (20) eap: Sending EAP Request (code 1) ID 1 length 6 (20) eap: EAP session adding &reply:State = 0xfa6d51bcfa6c4896 (20) [eap] = handled (20) } # authenticate = handled (20) Using Post-Auth-Type Challenge (20) # Executing group from file /etc/raddb/sites-enabled/default (20) Challenge { ... } # empty sub-section is ignored (20) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (20) EAP-Message = 0x010100061920 (20) Message-Authenticator = 0x00000000000000000000000000000000 (20) State = 0xfa6d51bcfa6c489698062bca06912e67 (20) Finished request Waking up in 4.9 seconds. (20) Cleaning up request packet ID 0 with timestamp +52 (21) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 309 (21) User-Name = "CLEARSYSTEM\\test1" (21) NAS-IP-Address = 172.22.22.254 (21) Called-Station-Id = "001601dfe596" (21) Calling-Station-Id = "74da38d41a8b" (21) NAS-Identifier = "001601dfe596" (21) NAS-Port = 5 (21) Framed-MTU = 1400 (21) State = 0xfa6d51bcfa6c489698062bca06912e67 (21) NAS-Port-Type = Wireless-802.11 (21) EAP-Message = 0x020100a619800000009c16030300970100009303035af2cd4182a5d752449f9f3c82907f8a3241b08562a2f580b7510c209b1ad8ee00002ac02cc02bc030c02f009f009ec024c023c028c027c00ac009c014c013009d009c003d003c0035002f000a01000040000500050100000000000a00080006001d (21) Message-Authenticator = 0xd7ca5568b71b5db979cc885bbb70864c (21) session-state: No cached attributes (21) # Executing section authorize from file /etc/raddb/sites-enabled/default (21) authorize { (21) policy filter_username { (21) if (&User-Name) { (21) if (&User-Name) -> TRUE (21) if (&User-Name) { (21) if (&User-Name =~ / /) { (21) if (&User-Name =~ / /) -> FALSE (21) if (&User-Name =~ /@[^@]*@/ ) { (21) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (21) if (&User-Name =~ /\.\./ ) { (21) if (&User-Name =~ /\.\./ ) -> FALSE (21) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (21) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (21) if (&User-Name =~ /\.$/) { (21) if (&User-Name =~ /\.$/) -> FALSE (21) if (&User-Name =~ /(a)\./) { (21) if (&User-Name =~ /(a)\./) -> FALSE (21) } # if (&User-Name) = notfound (21) } # policy filter_username = notfound (21) [preprocess] = ok (21) [chap] = noop (21) [mschap] = noop (21) [digest] = noop (21) suffix: Checking for suffix after "@" (21) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (21) suffix: No such realm "NULL" (21) [suffix] = noop (21) ntdomain: Checking for prefix before "\" (21) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (21) ntdomain: Found realm "CLEARSYSTEM" (21) ntdomain: Adding Stripped-User-Name = "test1" (21) ntdomain: Adding Realm = "CLEARSYSTEM" (21) ntdomain: Authentication realm is LOCAL (21) [ntdomain] = ok (21) eap: Peer sent EAP Response (code 2) ID 1 length 166 (21) eap: Continuing tunnel setup (21) [eap] = ok (21) } # authorize = ok (21) Found Auth-Type = eap (21) # Executing group from file /etc/raddb/sites-enabled/default (21) authenticate { (21) eap: Expiring EAP session with state 0xfa6d51bcfa6c4896 (21) eap: Finished EAP session with state 0xfa6d51bcfa6c4896 (21) eap: Previous EAP request found for state 0xfa6d51bcfa6c4896, released from the list (21) eap: Peer sent packet with method EAP PEAP (25) (21) eap: Calling submodule eap_peap to process data (21) eap_peap: Continuing EAP-TLS (21) eap_peap: Peer indicated complete TLS record size will be 156 bytes (21) eap_peap: Got complete TLS record (156 bytes) (21) eap_peap: [eaptls verify] = length included (21) eap_peap: (other): before/accept initialization (21) eap_peap: TLS_accept: before/accept initialization (21) eap_peap: <<< recv TLS 1.2 [length 0097] (21) eap_peap: TLS_accept: SSLv3 read client hello A (21) eap_peap: >>> send TLS 1.2 [length 0039] (21) eap_peap: TLS_accept: SSLv3 write server hello A (21) eap_peap: >>> send TLS 1.2 [length 08bd] (21) eap_peap: TLS_accept: SSLv3 write certificate A (21) eap_peap: >>> send TLS 1.2 [length 014d] (21) eap_peap: TLS_accept: SSLv3 write key exchange A (21) eap_peap: >>> send TLS 1.2 [length 0004] (21) eap_peap: TLS_accept: SSLv3 write server done A (21) eap_peap: TLS_accept: SSLv3 flush data (21) eap_peap: TLS_accept: SSLv3 read client certificate A (21) eap_peap: TLS_accept: Need to read more data: SSLv3 read client key exchange A (21) eap_peap: TLS_accept: Need to read more data: SSLv3 read client key exchange A (21) eap_peap: In SSL Handshake Phase (21) eap_peap: In SSL Accept mode (21) eap_peap: [eaptls process] = handled (21) eap: Sending EAP Request (code 1) ID 2 length 1004 (21) eap: EAP session adding &reply:State = 0xfa6d51bcfb6f4896 (21) [eap] = handled (21) } # authenticate = handled (21) Using Post-Auth-Type Challenge (21) # Executing group from file /etc/raddb/sites-enabled/default (21) Challenge { ... } # empty sub-section is ignored (21) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (21) EAP-Message = 0x010203ec19c000000a5b1603030039020000350303efe7db12e59487a4ce090d0f4ba3b259512e5009c80752cd2d3f4b01afc6b7ed00c03000000dff01000100000b00040300010216030308bd0b0008b90008b60003fb308203f7308202dfa003020102020101300d06092a864886f70d01010b050030 (21) Message-Authenticator = 0x00000000000000000000000000000000 (21) State = 0xfa6d51bcfb6f489698062bca06912e67 (21) Finished request Waking up in 4.9 seconds. (21) Cleaning up request packet ID 0 with timestamp +53 (22) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 149 (22) User-Name = "CLEARSYSTEM\\test1" (22) NAS-IP-Address = 172.22.22.254 (22) Called-Station-Id = "001601dfe596" (22) Calling-Station-Id = "74da38d41a8b" (22) NAS-Identifier = "001601dfe596" (22) NAS-Port = 5 (22) Framed-MTU = 1400 (22) State = 0xfa6d51bcfb6f489698062bca06912e67 (22) NAS-Port-Type = Wireless-802.11 (22) EAP-Message = 0x020200061900 (22) Message-Authenticator = 0xa6e13757d66ca64391cce7904f9323cb (22) session-state: No cached attributes (22) # Executing section authorize from file /etc/raddb/sites-enabled/default (22) authorize { (22) policy filter_username { (22) if (&User-Name) { (22) if (&User-Name) -> TRUE (22) if (&User-Name) { (22) if (&User-Name =~ / /) { (22) if (&User-Name =~ / /) -> FALSE (22) if (&User-Name =~ /@[^@]*@/ ) { (22) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (22) if (&User-Name =~ /\.\./ ) { (22) if (&User-Name =~ /\.\./ ) -> FALSE (22) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (22) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (22) if (&User-Name =~ /\.$/) { (22) if (&User-Name =~ /\.$/) -> FALSE (22) if (&User-Name =~ /(a)\./) { (22) if (&User-Name =~ /(a)\./) -> FALSE (22) } # if (&User-Name) = notfound (22) } # policy filter_username = notfound (22) [preprocess] = ok (22) [chap] = noop (22) [mschap] = noop (22) [digest] = noop (22) suffix: Checking for suffix after "@" (22) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (22) suffix: No such realm "NULL" (22) [suffix] = noop (22) ntdomain: Checking for prefix before "\" (22) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (22) ntdomain: Found realm "CLEARSYSTEM" (22) ntdomain: Adding Stripped-User-Name = "test1" (22) ntdomain: Adding Realm = "CLEARSYSTEM" (22) ntdomain: Authentication realm is LOCAL (22) [ntdomain] = ok (22) eap: Peer sent EAP Response (code 2) ID 2 length 6 (22) eap: Continuing tunnel setup (22) [eap] = ok (22) } # authorize = ok (22) Found Auth-Type = eap (22) # Executing group from file /etc/raddb/sites-enabled/default (22) authenticate { (22) eap: Expiring EAP session with state 0xfa6d51bcfb6f4896 (22) eap: Finished EAP session with state 0xfa6d51bcfb6f4896 (22) eap: Previous EAP request found for state 0xfa6d51bcfb6f4896, released from the list (22) eap: Peer sent packet with method EAP PEAP (25) (22) eap: Calling submodule eap_peap to process data (22) eap_peap: Continuing EAP-TLS (22) eap_peap: Peer ACKed our handshake fragment (22) eap_peap: [eaptls verify] = request (22) eap_peap: [eaptls process] = handled (22) eap: Sending EAP Request (code 1) ID 3 length 1000 (22) eap: EAP session adding &reply:State = 0xfa6d51bcf86e4896 (22) [eap] = handled (22) } # authenticate = handled (22) Using Post-Auth-Type Challenge (22) # Executing group from file /etc/raddb/sites-enabled/default (22) Challenge { ... } # empty sub-section is ignored (22) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (22) EAP-Message = 0x010303e819408444f5b804aa2d65ef2b23820bb1bf1bfcb24df6bd03eabe61d7bb630cfd9fd6165d19f24d23925593c04c7ec13d5afe51369fe487605e2de3073d043a15e72448712bca946e329e81ff36cebcdfe8be08dc6490da38ed9147e7eac88af7f25487bee0ef80700004b5308204b130820399 (22) Message-Authenticator = 0x00000000000000000000000000000000 (22) State = 0xfa6d51bcf86e489698062bca06912e67 (22) Finished request Waking up in 4.9 seconds. (22) Cleaning up request packet ID 0 with timestamp +53 (23) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 149 (23) User-Name = "CLEARSYSTEM\\test1" (23) NAS-IP-Address = 172.22.22.254 (23) Called-Station-Id = "001601dfe596" (23) Calling-Station-Id = "74da38d41a8b" (23) NAS-Identifier = "001601dfe596" (23) NAS-Port = 5 (23) Framed-MTU = 1400 (23) State = 0xfa6d51bcf86e489698062bca06912e67 (23) NAS-Port-Type = Wireless-802.11 (23) EAP-Message = 0x020300061900 (23) Message-Authenticator = 0x12fe245e46b21f527d4441886e6f31df (23) session-state: No cached attributes (23) # Executing section authorize from file /etc/raddb/sites-enabled/default (23) authorize { (23) policy filter_username { (23) if (&User-Name) { (23) if (&User-Name) -> TRUE (23) if (&User-Name) { (23) if (&User-Name =~ / /) { (23) if (&User-Name =~ / /) -> FALSE (23) if (&User-Name =~ /@[^@]*@/ ) { (23) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (23) if (&User-Name =~ /\.\./ ) { (23) if (&User-Name =~ /\.\./ ) -> FALSE (23) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (23) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (23) if (&User-Name =~ /\.$/) { (23) if (&User-Name =~ /\.$/) -> FALSE (23) if (&User-Name =~ /(a)\./) { (23) if (&User-Name =~ /(a)\./) -> FALSE (23) } # if (&User-Name) = notfound (23) } # policy filter_username = notfound (23) [preprocess] = ok (23) [chap] = noop (23) [mschap] = noop (23) [digest] = noop (23) suffix: Checking for suffix after "@" (23) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (23) suffix: No such realm "NULL" (23) [suffix] = noop (23) ntdomain: Checking for prefix before "\" (23) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (23) ntdomain: Found realm "CLEARSYSTEM" (23) ntdomain: Adding Stripped-User-Name = "test1" (23) ntdomain: Adding Realm = "CLEARSYSTEM" (23) ntdomain: Authentication realm is LOCAL (23) [ntdomain] = ok (23) eap: Peer sent EAP Response (code 2) ID 3 length 6 (23) eap: Continuing tunnel setup (23) [eap] = ok (23) } # authorize = ok (23) Found Auth-Type = eap (23) # Executing group from file /etc/raddb/sites-enabled/default (23) authenticate { (23) eap: Expiring EAP session with state 0xfa6d51bcf86e4896 (23) eap: Finished EAP session with state 0xfa6d51bcf86e4896 (23) eap: Previous EAP request found for state 0xfa6d51bcf86e4896, released from the list (23) eap: Peer sent packet with method EAP PEAP (25) (23) eap: Calling submodule eap_peap to process data (23) eap_peap: Continuing EAP-TLS (23) eap_peap: Peer ACKed our handshake fragment (23) eap_peap: [eaptls verify] = request (23) eap_peap: [eaptls process] = handled (23) eap: Sending EAP Request (code 1) ID 4 length 669 (23) eap: EAP session adding &reply:State = 0xfa6d51bcf9694896 (23) [eap] = handled (23) } # authenticate = handled (23) Using Post-Auth-Type Challenge (23) # Executing group from file /etc/raddb/sites-enabled/default (23) Challenge { ... } # empty sub-section is ignored (23) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (23) EAP-Message = 0x0104029d1900278625687474703a2f2f7777772e6578616d706c652e6f72672f6578616d706c655f63612e63726c300d06092a864886f70d01010b050003820101000132a42023b4da19cd0464809979cba06e09409f4cbae9db226b41b48d0c97de8fa6092c00476cb9f16399e310996fb68c40e69b10 (23) Message-Authenticator = 0x00000000000000000000000000000000 (23) State = 0xfa6d51bcf969489698062bca06912e67 (23) Finished request Waking up in 4.9 seconds. (23) Cleaning up request packet ID 0 with timestamp +53 (24) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 279 (24) User-Name = "CLEARSYSTEM\\test1" (24) NAS-IP-Address = 172.22.22.254 (24) Called-Station-Id = "001601dfe596" (24) Calling-Station-Id = "74da38d41a8b" (24) NAS-Identifier = "001601dfe596" (24) NAS-Port = 5 (24) Framed-MTU = 1400 (24) State = 0xfa6d51bcf969489698062bca06912e67 (24) NAS-Port-Type = Wireless-802.11 (24) EAP-Message = 0x0204008819800000007e16030300461000004241049e1a625d2b93e6a0c9c56f2c9ac9ff69abdc4f1ca93b1351d875e78f8aa12296537dfac26fda08297759aa812bdcd6a246e57257ee8f71aa07939bb4a5f5f6a914030300010116030300280000000000000000c1c16214c7db50ef874f9234cd8c36 (24) Message-Authenticator = 0xef04f914f34ef56740417c68c8f84c29 (24) session-state: No cached attributes (24) # Executing section authorize from file /etc/raddb/sites-enabled/default (24) authorize { (24) policy filter_username { (24) if (&User-Name) { (24) if (&User-Name) -> TRUE (24) if (&User-Name) { (24) if (&User-Name =~ / /) { (24) if (&User-Name =~ / /) -> FALSE (24) if (&User-Name =~ /@[^@]*@/ ) { (24) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (24) if (&User-Name =~ /\.\./ ) { (24) if (&User-Name =~ /\.\./ ) -> FALSE (24) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (24) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (24) if (&User-Name =~ /\.$/) { (24) if (&User-Name =~ /\.$/) -> FALSE (24) if (&User-Name =~ /(a)\./) { (24) if (&User-Name =~ /(a)\./) -> FALSE (24) } # if (&User-Name) = notfound (24) } # policy filter_username = notfound (24) [preprocess] = ok (24) [chap] = noop (24) [mschap] = noop (24) [digest] = noop (24) suffix: Checking for suffix after "@" (24) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (24) suffix: No such realm "NULL" (24) [suffix] = noop (24) ntdomain: Checking for prefix before "\" (24) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (24) ntdomain: Found realm "CLEARSYSTEM" (24) ntdomain: Adding Stripped-User-Name = "test1" (24) ntdomain: Adding Realm = "CLEARSYSTEM" (24) ntdomain: Authentication realm is LOCAL (24) [ntdomain] = ok (24) eap: Peer sent EAP Response (code 2) ID 4 length 136 (24) eap: Continuing tunnel setup (24) [eap] = ok (24) } # authorize = ok (24) Found Auth-Type = eap (24) # Executing group from file /etc/raddb/sites-enabled/default (24) authenticate { (24) eap: Expiring EAP session with state 0xfa6d51bcf9694896 (24) eap: Finished EAP session with state 0xfa6d51bcf9694896 (24) eap: Previous EAP request found for state 0xfa6d51bcf9694896, released from the list (24) eap: Peer sent packet with method EAP PEAP (25) (24) eap: Calling submodule eap_peap to process data (24) eap_peap: Continuing EAP-TLS (24) eap_peap: Peer indicated complete TLS record size will be 126 bytes (24) eap_peap: Got complete TLS record (126 bytes) (24) eap_peap: [eaptls verify] = length included (24) eap_peap: <<< recv TLS 1.2 [length 0046] (24) eap_peap: TLS_accept: SSLv3 read client key exchange A (24) eap_peap: TLS_accept: SSLv3 read certificate verify A (24) eap_peap: <<< recv TLS 1.2 [length 0001] (24) eap_peap: <<< recv TLS 1.2 [length 0010] (24) eap_peap: TLS_accept: SSLv3 read finished A (24) eap_peap: >>> send TLS 1.2 [length 0001] (24) eap_peap: TLS_accept: SSLv3 write change cipher spec A (24) eap_peap: >>> send TLS 1.2 [length 0010] (24) eap_peap: TLS_accept: SSLv3 write finished A (24) eap_peap: TLS_accept: SSLv3 flush data (24) eap_peap: (other): SSL negotiation finished successfully (24) eap_peap: SSL Connection Established (24) eap_peap: [eaptls process] = handled (24) eap: Sending EAP Request (code 1) ID 5 length 57 (24) eap: EAP session adding &reply:State = 0xfa6d51bcfe684896 (24) [eap] = handled (24) } # authenticate = handled (24) Using Post-Auth-Type Challenge (24) # Executing group from file /etc/raddb/sites-enabled/default (24) Challenge { ... } # empty sub-section is ignored (24) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (24) EAP-Message = 0x01050039190014030300010116030300289fc5de61f40ef791b66109d7e36af16596d84e0d117df80d2a801f121f79b4700b8a5712ac9eb200 (24) Message-Authenticator = 0x00000000000000000000000000000000 (24) State = 0xfa6d51bcfe68489698062bca06912e67 (24) Finished request Waking up in 4.9 seconds. (24) Cleaning up request packet ID 0 with timestamp +53 (25) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 149 (25) User-Name = "CLEARSYSTEM\\test1" (25) NAS-IP-Address = 172.22.22.254 (25) Called-Station-Id = "001601dfe596" (25) Calling-Station-Id = "74da38d41a8b" (25) NAS-Identifier = "001601dfe596" (25) NAS-Port = 5 (25) Framed-MTU = 1400 (25) State = 0xfa6d51bcfe68489698062bca06912e67 (25) NAS-Port-Type = Wireless-802.11 (25) EAP-Message = 0x020500061900 (25) Message-Authenticator = 0xc4d5b25261ca14db4b0b4afd1509d942 (25) session-state: No cached attributes (25) # Executing section authorize from file /etc/raddb/sites-enabled/default (25) authorize { (25) policy filter_username { (25) if (&User-Name) { (25) if (&User-Name) -> TRUE (25) if (&User-Name) { (25) if (&User-Name =~ / /) { (25) if (&User-Name =~ / /) -> FALSE (25) if (&User-Name =~ /@[^@]*@/ ) { (25) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (25) if (&User-Name =~ /\.\./ ) { (25) if (&User-Name =~ /\.\./ ) -> FALSE (25) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (25) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (25) if (&User-Name =~ /\.$/) { (25) if (&User-Name =~ /\.$/) -> FALSE (25) if (&User-Name =~ /(a)\./) { (25) if (&User-Name =~ /(a)\./) -> FALSE (25) } # if (&User-Name) = notfound (25) } # policy filter_username = notfound (25) [preprocess] = ok (25) [chap] = noop (25) [mschap] = noop (25) [digest] = noop (25) suffix: Checking for suffix after "@" (25) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (25) suffix: No such realm "NULL" (25) [suffix] = noop (25) ntdomain: Checking for prefix before "\" (25) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (25) ntdomain: Found realm "CLEARSYSTEM" (25) ntdomain: Adding Stripped-User-Name = "test1" (25) ntdomain: Adding Realm = "CLEARSYSTEM" (25) ntdomain: Authentication realm is LOCAL (25) [ntdomain] = ok (25) eap: Peer sent EAP Response (code 2) ID 5 length 6 (25) eap: Continuing tunnel setup (25) [eap] = ok (25) } # authorize = ok (25) Found Auth-Type = eap (25) # Executing group from file /etc/raddb/sites-enabled/default (25) authenticate { (25) eap: Expiring EAP session with state 0xfa6d51bcfe684896 (25) eap: Finished EAP session with state 0xfa6d51bcfe684896 (25) eap: Previous EAP request found for state 0xfa6d51bcfe684896, released from the list (25) eap: Peer sent packet with method EAP PEAP (25) (25) eap: Calling submodule eap_peap to process data (25) eap_peap: Continuing EAP-TLS (25) eap_peap: Peer ACKed our handshake fragment. handshake is finished (25) eap_peap: [eaptls verify] = success (25) eap_peap: [eaptls process] = success (25) eap_peap: Session established. Decoding tunneled attributes (25) eap_peap: PEAP state TUNNEL ESTABLISHED (25) eap: Sending EAP Request (code 1) ID 6 length 40 (25) eap: EAP session adding &reply:State = 0xfa6d51bcff6b4896 (25) [eap] = handled (25) } # authenticate = handled (25) Using Post-Auth-Type Challenge (25) # Executing group from file /etc/raddb/sites-enabled/default (25) Challenge { ... } # empty sub-section is ignored (25) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (25) EAP-Message = 0x010600281900170303001d9fc5de61f40ef7925497e0f03071577e94fda8fc4dca1cd9802e483d4e (25) Message-Authenticator = 0x00000000000000000000000000000000 (25) State = 0xfa6d51bcff6b489698062bca06912e67 (25) Finished request Waking up in 4.9 seconds. (25) Cleaning up request packet ID 0 with timestamp +53 (26) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 196 (26) User-Name = "CLEARSYSTEM\\test1" (26) NAS-IP-Address = 172.22.22.254 (26) Called-Station-Id = "001601dfe596" (26) Calling-Station-Id = "74da38d41a8b" (26) NAS-Identifier = "001601dfe596" (26) NAS-Port = 5 (26) Framed-MTU = 1400 (26) State = 0xfa6d51bcff6b489698062bca06912e67 (26) NAS-Port-Type = Wireless-802.11 (26) EAP-Message = 0x020600351900170303002a00000000000000010c933fa0100b5f27e5b96564694cce21d984340dcb6f16c8d77d6ca418f7bc3355c0 (26) Message-Authenticator = 0x3bb9fc8b6b5e0df1d67ba95dd5dded2d (26) session-state: No cached attributes (26) # Executing section authorize from file /etc/raddb/sites-enabled/default (26) authorize { (26) policy filter_username { (26) if (&User-Name) { (26) if (&User-Name) -> TRUE (26) if (&User-Name) { (26) if (&User-Name =~ / /) { (26) if (&User-Name =~ / /) -> FALSE (26) if (&User-Name =~ /@[^@]*@/ ) { (26) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (26) if (&User-Name =~ /\.\./ ) { (26) if (&User-Name =~ /\.\./ ) -> FALSE (26) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (26) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (26) if (&User-Name =~ /\.$/) { (26) if (&User-Name =~ /\.$/) -> FALSE (26) if (&User-Name =~ /(a)\./) { (26) if (&User-Name =~ /(a)\./) -> FALSE (26) } # if (&User-Name) = notfound (26) } # policy filter_username = notfound (26) [preprocess] = ok (26) [chap] = noop (26) [mschap] = noop (26) [digest] = noop (26) suffix: Checking for suffix after "@" (26) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (26) suffix: No such realm "NULL" (26) [suffix] = noop (26) ntdomain: Checking for prefix before "\" (26) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (26) ntdomain: Found realm "CLEARSYSTEM" (26) ntdomain: Adding Stripped-User-Name = "test1" (26) ntdomain: Adding Realm = "CLEARSYSTEM" (26) ntdomain: Authentication realm is LOCAL (26) [ntdomain] = ok (26) eap: Peer sent EAP Response (code 2) ID 6 length 53 (26) eap: Continuing tunnel setup (26) [eap] = ok (26) } # authorize = ok (26) Found Auth-Type = eap (26) # Executing group from file /etc/raddb/sites-enabled/default (26) authenticate { (26) eap: Expiring EAP session with state 0xfa6d51bcff6b4896 (26) eap: Finished EAP session with state 0xfa6d51bcff6b4896 (26) eap: Previous EAP request found for state 0xfa6d51bcff6b4896, released from the list (26) eap: Peer sent packet with method EAP PEAP (25) (26) eap: Calling submodule eap_peap to process data (26) eap_peap: Continuing EAP-TLS (26) eap_peap: [eaptls verify] = ok (26) eap_peap: Done initial handshake (26) eap_peap: [eaptls process] = ok (26) eap_peap: Session established. Decoding tunneled attributes (26) eap_peap: PEAP state WAITING FOR INNER IDENTITY (26) eap_peap: Identity - CLEARSYSTEM\test1 (26) eap_peap: Got inner identity 'CLEARSYSTEM\test1' (26) eap_peap: Setting default EAP type for tunneled EAP session (26) eap_peap: Got tunneled request (26) eap_peap: EAP-Message = 0x0206001601434c45415253595354454d5c7465737431 (26) eap_peap: Setting User-Name to CLEARSYSTEM\test1 (26) eap_peap: Sending tunneled request to inner-tunnel (26) eap_peap: EAP-Message = 0x0206001601434c45415253595354454d5c7465737431 (26) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1 (26) eap_peap: User-Name = "CLEARSYSTEM\\test1" (26) Virtual server inner-tunnel received request (26) EAP-Message = 0x0206001601434c45415253595354454d5c7465737431 (26) FreeRADIUS-Proxied-To = 127.0.0.1 (26) User-Name = "CLEARSYSTEM\\test1" (26) WARNING: Outer and inner identities are the same. User privacy is compromised. (26) server inner-tunnel { (26) # Executing section authorize from file /etc/raddb/sites-enabled/inner-tunnel (26) authorize { (26) policy filter_username { (26) if (&User-Name) { (26) if (&User-Name) -> TRUE (26) if (&User-Name) { (26) if (&User-Name =~ / /) { (26) if (&User-Name =~ / /) -> FALSE (26) if (&User-Name =~ /@[^@]*@/ ) { (26) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (26) if (&User-Name =~ /\.\./ ) { (26) if (&User-Name =~ /\.\./ ) -> FALSE (26) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (26) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (26) if (&User-Name =~ /\.$/) { (26) if (&User-Name =~ /\.$/) -> FALSE (26) if (&User-Name =~ /(a)\./) { (26) if (&User-Name =~ /(a)\./) -> FALSE (26) } # if (&User-Name) = notfound (26) } # policy filter_username = notfound (26) [chap] = noop (26) [mschap] = noop (26) suffix: Checking for suffix after "@" (26) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (26) suffix: No such realm "NULL" (26) [suffix] = noop (26) ntdomain: Checking for prefix before "\" (26) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (26) ntdomain: Found realm "CLEARSYSTEM" (26) ntdomain: Adding Stripped-User-Name = "test1" (26) ntdomain: Adding Realm = "CLEARSYSTEM" (26) ntdomain: Authentication realm is LOCAL (26) [ntdomain] = ok (26) update control { (26) &Proxy-To-Realm := LOCAL (26) } # update control = noop (26) eap: Peer sent EAP Response (code 2) ID 6 length 22 (26) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize (26) [eap] = ok (26) } # authorize = ok (26) Found Auth-Type = eap (26) # Executing group from file /etc/raddb/sites-enabled/inner-tunnel (26) authenticate { (26) eap: Peer sent packet with method EAP Identity (1) (26) eap: Calling submodule eap_mschapv2 to process data (26) eap_mschapv2: Issuing Challenge (26) eap: Sending EAP Request (code 1) ID 7 length 43 (26) eap: EAP session adding &reply:State = 0x67f4154867f30fc7 (26) [eap] = handled (26) } # authenticate = handled (26) } # server inner-tunnel (26) Virtual server sending reply (26) EAP-Message = 0x0107002b1a0107002610924e60a23ee51c27491d1ede23d3f645667265657261646975732d332e302e3133 (26) Message-Authenticator = 0x00000000000000000000000000000000 (26) State = 0x67f4154867f30fc7e3fcab03d0b75466 (26) eap_peap: Got tunneled reply code 11 (26) eap_peap: EAP-Message = 0x0107002b1a0107002610924e60a23ee51c27491d1ede23d3f645667265657261646975732d332e302e3133 (26) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (26) eap_peap: State = 0x67f4154867f30fc7e3fcab03d0b75466 (26) eap_peap: Got tunneled reply RADIUS code 11 (26) eap_peap: EAP-Message = 0x0107002b1a0107002610924e60a23ee51c27491d1ede23d3f645667265657261646975732d332e302e3133 (26) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (26) eap_peap: State = 0x67f4154867f30fc7e3fcab03d0b75466 (26) eap_peap: Got tunneled Access-Challenge (26) eap: Sending EAP Request (code 1) ID 7 length 74 (26) eap: EAP session adding &reply:State = 0xfa6d51bcfc6a4896 (26) [eap] = handled (26) } # authenticate = handled (26) Using Post-Auth-Type Challenge (26) # Executing group from file /etc/raddb/sites-enabled/default (26) Challenge { ... } # empty sub-section is ignored (26) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (26) EAP-Message = 0x0107004a1900170303003f9fc5de61f40ef79320067b88f1b9e625058f12902741fb970becb9261d941d1b266fa753bee467888aab0af7d34c9f313426aa5a51d1aa69aa798529ede786 (26) Message-Authenticator = 0x00000000000000000000000000000000 (26) State = 0xfa6d51bcfc6a489698062bca06912e67 (26) Finished request Waking up in 4.9 seconds. (26) Cleaning up request packet ID 0 with timestamp +53 (27) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 250 (27) User-Name = "CLEARSYSTEM\\test1" (27) NAS-IP-Address = 172.22.22.254 (27) Called-Station-Id = "001601dfe596" (27) Calling-Station-Id = "74da38d41a8b" (27) NAS-Identifier = "001601dfe596" (27) NAS-Port = 5 (27) Framed-MTU = 1400 (27) State = 0xfa6d51bcfc6a489698062bca06912e67 (27) NAS-Port-Type = Wireless-802.11 (27) EAP-Message = 0x0207006b1900170303006000000000000000021164b401a6b91edb40d45e1ae33a3fea0cec4342e9431f3070feae69d5c873b621ce5e2ca831677e11c81a47eb117c073c0825ef4ce462d2b041e0dbe753411783cbeed0efd3072a2d2548310371af5a119da170a961b921 (27) Message-Authenticator = 0xf080de21399d6eac0a27d43417e9a92c (27) session-state: No cached attributes (27) # Executing section authorize from file /etc/raddb/sites-enabled/default (27) authorize { (27) policy filter_username { (27) if (&User-Name) { (27) if (&User-Name) -> TRUE (27) if (&User-Name) { (27) if (&User-Name =~ / /) { (27) if (&User-Name =~ / /) -> FALSE (27) if (&User-Name =~ /@[^@]*@/ ) { (27) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (27) if (&User-Name =~ /\.\./ ) { (27) if (&User-Name =~ /\.\./ ) -> FALSE (27) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (27) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (27) if (&User-Name =~ /\.$/) { (27) if (&User-Name =~ /\.$/) -> FALSE (27) if (&User-Name =~ /(a)\./) { (27) if (&User-Name =~ /(a)\./) -> FALSE (27) } # if (&User-Name) = notfound (27) } # policy filter_username = notfound (27) [preprocess] = ok (27) [chap] = noop (27) [mschap] = noop (27) [digest] = noop (27) suffix: Checking for suffix after "@" (27) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (27) suffix: No such realm "NULL" (27) [suffix] = noop (27) ntdomain: Checking for prefix before "\" (27) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (27) ntdomain: Found realm "CLEARSYSTEM" (27) ntdomain: Adding Stripped-User-Name = "test1" (27) ntdomain: Adding Realm = "CLEARSYSTEM" (27) ntdomain: Authentication realm is LOCAL (27) [ntdomain] = ok (27) eap: Peer sent EAP Response (code 2) ID 7 length 107 (27) eap: Continuing tunnel setup (27) [eap] = ok (27) } # authorize = ok (27) Found Auth-Type = eap (27) # Executing group from file /etc/raddb/sites-enabled/default (27) authenticate { (27) eap: Expiring EAP session with state 0x67f4154867f30fc7 (27) eap: Finished EAP session with state 0xfa6d51bcfc6a4896 (27) eap: Previous EAP request found for state 0xfa6d51bcfc6a4896, released from the list (27) eap: Peer sent packet with method EAP PEAP (25) (27) eap: Calling submodule eap_peap to process data (27) eap_peap: Continuing EAP-TLS (27) eap_peap: [eaptls verify] = ok (27) eap_peap: Done initial handshake (27) eap_peap: [eaptls process] = ok (27) eap_peap: Session established. Decoding tunneled attributes (27) eap_peap: PEAP state phase2 (27) eap_peap: EAP method MSCHAPv2 (26) (27) eap_peap: Got tunneled request (27) eap_peap: EAP-Message = 0x0207004c1a02070047318ebe9e5e7d389ad1bc7eb58ddee3294600000000000000009192d897cc33bc83f03bd7b7e725852e1cefe0cd1cabcebc00434c45415253595354454d5c7465737431 (27) eap_peap: Setting User-Name to CLEARSYSTEM\test1 (27) eap_peap: Sending tunneled request to inner-tunnel (27) eap_peap: EAP-Message = 0x0207004c1a02070047318ebe9e5e7d389ad1bc7eb58ddee3294600000000000000009192d897cc33bc83f03bd7b7e725852e1cefe0cd1cabcebc00434c45415253595354454d5c7465737431 (27) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1 (27) eap_peap: User-Name = "CLEARSYSTEM\\test1" (27) eap_peap: State = 0x67f4154867f30fc7e3fcab03d0b75466 (27) Virtual server inner-tunnel received request (27) EAP-Message = 0x0207004c1a02070047318ebe9e5e7d389ad1bc7eb58ddee3294600000000000000009192d897cc33bc83f03bd7b7e725852e1cefe0cd1cabcebc00434c45415253595354454d5c7465737431 (27) FreeRADIUS-Proxied-To = 127.0.0.1 (27) User-Name = "CLEARSYSTEM\\test1" (27) State = 0x67f4154867f30fc7e3fcab03d0b75466 (27) WARNING: Outer and inner identities are the same. User privacy is compromised. (27) server inner-tunnel { (27) session-state: No cached attributes (27) # Executing section authorize from file /etc/raddb/sites-enabled/inner-tunnel (27) authorize { (27) policy filter_username { (27) if (&User-Name) { (27) if (&User-Name) -> TRUE (27) if (&User-Name) { (27) if (&User-Name =~ / /) { (27) if (&User-Name =~ / /) -> FALSE (27) if (&User-Name =~ /@[^@]*@/ ) { (27) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (27) if (&User-Name =~ /\.\./ ) { (27) if (&User-Name =~ /\.\./ ) -> FALSE (27) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (27) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (27) if (&User-Name =~ /\.$/) { (27) if (&User-Name =~ /\.$/) -> FALSE (27) if (&User-Name =~ /(a)\./) { (27) if (&User-Name =~ /(a)\./) -> FALSE (27) } # if (&User-Name) = notfound (27) } # policy filter_username = notfound (27) [chap] = noop (27) [mschap] = noop (27) suffix: Checking for suffix after "@" (27) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (27) suffix: No such realm "NULL" (27) [suffix] = noop (27) ntdomain: Checking for prefix before "\" (27) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (27) ntdomain: Found realm "CLEARSYSTEM" (27) ntdomain: Adding Stripped-User-Name = "test1" (27) ntdomain: Adding Realm = "CLEARSYSTEM" (27) ntdomain: Authentication realm is LOCAL (27) [ntdomain] = ok (27) update control { (27) &Proxy-To-Realm := LOCAL (27) } # update control = noop (27) eap: Peer sent EAP Response (code 2) ID 7 length 76 (27) eap: No EAP Start, assuming it's an on-going EAP conversation (27) [eap] = updated (27) files: Searching for user in group "allusers" rlm_ldap (ldap): Reserved connection (4) (27) files: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (27) files: --> (uid=test1) (27) files: Performing search in "dc=system,dc=lan" with filter "(uid=test1)", scope "sub" (27) files: Waiting for search result... (27) files: User object found at DN "cn=test1 test1,ou=Users,ou=Accounts,dc=system,dc=lan" (27) files: Checking user object's memberOf attributes (27) files: Performing unfiltered search in "cn=test1 test1,ou=Users,ou=Accounts,dc=system,dc=lan", scope "base" (27) files: Waiting for search result... (27) files: Processing memberOf value "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (27) files: Resolving group DN "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (27) files: Performing unfiltered search in "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (27) files: Waiting for search result... (27) files: Group DN "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "ftp_plugin" (27) files: Processing memberOf value "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (27) files: Resolving group DN "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (27) files: Performing unfiltered search in "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (27) files: Waiting for search result... (27) files: Group DN "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "web_proxy_plugin" (27) files: Processing memberOf value "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (27) files: Resolving group DN "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (27) files: Performing unfiltered search in "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (27) files: Waiting for search result... (27) files: Group DN "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "webupload" (27) files: Processing memberOf value "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (27) files: Resolving group DN "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (27) files: Performing unfiltered search in "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (27) files: Waiting for search result... (27) files: Group DN "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "allusers" (27) files: User found in group "allusers". Comparison between membership: name (resolved from DN "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=l?"), check: name rlm_ldap (ldap): Released connection (4) (27) [files] = noop rlm_ldap (ldap): Reserved connection (1) (27) ldap: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (27) ldap: --> (uid=test1) (27) ldap: Performing search in "dc=system,dc=lan" with filter "(uid=test1)", scope "sub" (27) ldap: Waiting for search result... (27) ldap: User object found at DN "cn=test1 test1,ou=Users,ou=Accounts,dc=system,dc=lan" (27) ldap: Processing user attributes (27) ldap: control:Password-With-Header += '{sha}tESsBmE/yNY3lb6a0L6vVQEZNqw=' rlm_ldap (ldap): Released connection (1) (27) [ldap] = updated (27) [expiration] = noop (27) [logintime] = noop (27) pap: Converted: &control:Password-With-Header -> &control:SHA1-Password (27) pap: Removing &control:Password-With-Header (27) pap: Normalizing SHA1-Password from base64 encoding, 28 bytes -> 20 bytes (27) pap: WARNING: Auth-Type already set. Not setting to PAP (27) [pap] = noop (27) } # authorize = updated (27) Found Auth-Type = eap (27) # Executing group from file /etc/raddb/sites-enabled/inner-tunnel (27) authenticate { (27) eap: Expiring EAP session with state 0x67f4154867f30fc7 (27) eap: Finished EAP session with state 0x67f4154867f30fc7 (27) eap: Previous EAP request found for state 0x67f4154867f30fc7, released from the list (27) eap: Peer sent packet with method EAP MSCHAPv2 (26) (27) eap: Calling submodule eap_mschapv2 to process data (27) eap_mschapv2: # Executing group from file /etc/raddb/sites-enabled/inner-tunnel (27) eap_mschapv2: authenticate { (27) mschap: Creating challenge hash with username: test1 (27) mschap: Client is using MS-CHAPv2 (27) mschap: Executing: /usr/bin/ntlm_auth --request-nt-key --username=%{%{Stripped-User-Name}:-%{%{User-Name}:-None}} --challenge=%{%{mschap:Challenge}:-00} --nt-response=%{%{mschap:NT-Response}:-00}: (27) mschap: EXPAND --username=%{%{Stripped-User-Name}:-%{%{User-Name}:-None}} (27) mschap: --> --username=test1 (27) mschap: Creating challenge hash with username: test1 (27) mschap: EXPAND --challenge=%{%{mschap:Challenge}:-00} (27) mschap: --> --challenge=b7881bdaef5718d0 (27) mschap: EXPAND --nt-response=%{%{mschap:NT-Response}:-00} (27) mschap: --> --nt-response=9192d897cc33bc83f03bd7b7e725852e1cefe0cd1cabcebc (27) mschap: Program returned code (0) and output 'NT_KEY: DAE53F1776DBD0817C5639A27629A27D' (27) mschap: Adding MS-CHAPv2 MPPE keys (27) [mschap] = ok (27) } # authenticate = ok (27) MSCHAP Success (27) eap: Sending EAP Request (code 1) ID 8 length 51 (27) eap: EAP session adding &reply:State = 0x67f4154866fc0fc7 (27) [eap] = handled (27) } # authenticate = handled (27) } # server inner-tunnel (27) Virtual server sending reply (27) EAP-Message = 0x010800331a0307002e533d43433037464444353744443738353244433532393433303036333836383832433333303235313235 (27) Message-Authenticator = 0x00000000000000000000000000000000 (27) State = 0x67f4154866fc0fc7e3fcab03d0b75466 (27) eap_peap: Got tunneled reply code 11 (27) eap_peap: EAP-Message = 0x010800331a0307002e533d43433037464444353744443738353244433532393433303036333836383832433333303235313235 (27) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (27) eap_peap: State = 0x67f4154866fc0fc7e3fcab03d0b75466 (27) eap_peap: Got tunneled reply RADIUS code 11 (27) eap_peap: EAP-Message = 0x010800331a0307002e533d43433037464444353744443738353244433532393433303036333836383832433333303235313235 (27) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (27) eap_peap: State = 0x67f4154866fc0fc7e3fcab03d0b75466 (27) eap_peap: Got tunneled Access-Challenge (27) eap: Sending EAP Request (code 1) ID 8 length 82 (27) eap: EAP session adding &reply:State = 0xfa6d51bcfd654896 (27) [eap] = handled (27) } # authenticate = handled (27) Using Post-Auth-Type Challenge (27) # Executing group from file /etc/raddb/sites-enabled/default (27) Challenge { ... } # empty sub-section is ignored (27) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (27) EAP-Message = 0x01080052190017030300479fc5de61f40ef79494eff5694d56e768cdb21779bc552c78a169ac0f8530b9de062bb9e00f19afd761d18aabce43510a9de602925b9274ddb52b6383f31803be6bd4971c2690bf (27) Message-Authenticator = 0x00000000000000000000000000000000 (27) State = 0xfa6d51bcfd65489698062bca06912e67 (27) Finished request Waking up in 4.9 seconds. (27) Cleaning up request packet ID 0 with timestamp +53 (28) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 180 (28) User-Name = "CLEARSYSTEM\\test1" (28) NAS-IP-Address = 172.22.22.254 (28) Called-Station-Id = "001601dfe596" (28) Calling-Station-Id = "74da38d41a8b" (28) NAS-Identifier = "001601dfe596" (28) NAS-Port = 5 (28) Framed-MTU = 1400 (28) State = 0xfa6d51bcfd65489698062bca06912e67 (28) NAS-Port-Type = Wireless-802.11 (28) EAP-Message = 0x020800251900170303001a0000000000000003f17c071701f2900218e05b0493a96e129742 (28) Message-Authenticator = 0x1d570e56fa27451711dbb7b15f04968d (28) session-state: No cached attributes (28) # Executing section authorize from file /etc/raddb/sites-enabled/default (28) authorize { (28) policy filter_username { (28) if (&User-Name) { (28) if (&User-Name) -> TRUE (28) if (&User-Name) { (28) if (&User-Name =~ / /) { (28) if (&User-Name =~ / /) -> FALSE (28) if (&User-Name =~ /@[^@]*@/ ) { (28) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (28) if (&User-Name =~ /\.\./ ) { (28) if (&User-Name =~ /\.\./ ) -> FALSE (28) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (28) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (28) if (&User-Name =~ /\.$/) { (28) if (&User-Name =~ /\.$/) -> FALSE (28) if (&User-Name =~ /(a)\./) { (28) if (&User-Name =~ /(a)\./) -> FALSE (28) } # if (&User-Name) = notfound (28) } # policy filter_username = notfound (28) [preprocess] = ok (28) [chap] = noop (28) [mschap] = noop (28) [digest] = noop (28) suffix: Checking for suffix after "@" (28) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (28) suffix: No such realm "NULL" (28) [suffix] = noop (28) ntdomain: Checking for prefix before "\" (28) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (28) ntdomain: Found realm "CLEARSYSTEM" (28) ntdomain: Adding Stripped-User-Name = "test1" (28) ntdomain: Adding Realm = "CLEARSYSTEM" (28) ntdomain: Authentication realm is LOCAL (28) [ntdomain] = ok (28) eap: Peer sent EAP Response (code 2) ID 8 length 37 (28) eap: Continuing tunnel setup (28) [eap] = ok (28) } # authorize = ok (28) Found Auth-Type = eap (28) # Executing group from file /etc/raddb/sites-enabled/default (28) authenticate { (28) eap: Expiring EAP session with state 0x67f4154866fc0fc7 (28) eap: Finished EAP session with state 0xfa6d51bcfd654896 (28) eap: Previous EAP request found for state 0xfa6d51bcfd654896, released from the list (28) eap: Peer sent packet with method EAP PEAP (25) (28) eap: Calling submodule eap_peap to process data (28) eap_peap: Continuing EAP-TLS (28) eap_peap: [eaptls verify] = ok (28) eap_peap: Done initial handshake (28) eap_peap: [eaptls process] = ok (28) eap_peap: Session established. Decoding tunneled attributes (28) eap_peap: PEAP state phase2 (28) eap_peap: EAP method MSCHAPv2 (26) (28) eap_peap: Got tunneled request (28) eap_peap: EAP-Message = 0x020800061a03 (28) eap_peap: Setting User-Name to CLEARSYSTEM\test1 (28) eap_peap: Sending tunneled request to inner-tunnel (28) eap_peap: EAP-Message = 0x020800061a03 (28) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1 (28) eap_peap: User-Name = "CLEARSYSTEM\\test1" (28) eap_peap: State = 0x67f4154866fc0fc7e3fcab03d0b75466 (28) Virtual server inner-tunnel received request (28) EAP-Message = 0x020800061a03 (28) FreeRADIUS-Proxied-To = 127.0.0.1 (28) User-Name = "CLEARSYSTEM\\test1" (28) State = 0x67f4154866fc0fc7e3fcab03d0b75466 (28) WARNING: Outer and inner identities are the same. User privacy is compromised. (28) server inner-tunnel { (28) session-state: No cached attributes (28) # Executing section authorize from file /etc/raddb/sites-enabled/inner-tunnel (28) authorize { (28) policy filter_username { (28) if (&User-Name) { (28) if (&User-Name) -> TRUE (28) if (&User-Name) { (28) if (&User-Name =~ / /) { (28) if (&User-Name =~ / /) -> FALSE (28) if (&User-Name =~ /@[^@]*@/ ) { (28) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (28) if (&User-Name =~ /\.\./ ) { (28) if (&User-Name =~ /\.\./ ) -> FALSE (28) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (28) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (28) if (&User-Name =~ /\.$/) { (28) if (&User-Name =~ /\.$/) -> FALSE (28) if (&User-Name =~ /(a)\./) { (28) if (&User-Name =~ /(a)\./) -> FALSE (28) } # if (&User-Name) = notfound (28) } # policy filter_username = notfound (28) [chap] = noop (28) [mschap] = noop (28) suffix: Checking for suffix after "@" (28) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (28) suffix: No such realm "NULL" (28) [suffix] = noop (28) ntdomain: Checking for prefix before "\" (28) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (28) ntdomain: Found realm "CLEARSYSTEM" (28) ntdomain: Adding Stripped-User-Name = "test1" (28) ntdomain: Adding Realm = "CLEARSYSTEM" (28) ntdomain: Authentication realm is LOCAL (28) [ntdomain] = ok (28) update control { (28) &Proxy-To-Realm := LOCAL (28) } # update control = noop (28) eap: Peer sent EAP Response (code 2) ID 8 length 6 (28) eap: No EAP Start, assuming it's an on-going EAP conversation (28) [eap] = updated (28) files: Searching for user in group "allusers" rlm_ldap (ldap): Reserved connection (2) (28) files: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (28) files: --> (uid=test1) (28) files: Performing search in "dc=system,dc=lan" with filter "(uid=test1)", scope "sub" (28) files: Waiting for search result... (28) files: User object found at DN "cn=test1 test1,ou=Users,ou=Accounts,dc=system,dc=lan" (28) files: Checking user object's memberOf attributes (28) files: Performing unfiltered search in "cn=test1 test1,ou=Users,ou=Accounts,dc=system,dc=lan", scope "base" (28) files: Waiting for search result... (28) files: Processing memberOf value "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (28) files: Resolving group DN "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (28) files: Performing unfiltered search in "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (28) files: Waiting for search result... (28) files: Group DN "cn=ftp_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "ftp_plugin" (28) files: Processing memberOf value "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (28) files: Resolving group DN "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (28) files: Performing unfiltered search in "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (28) files: Waiting for search result... (28) files: Group DN "cn=web_proxy_plugin,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "web_proxy_plugin" (28) files: Processing memberOf value "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (28) files: Resolving group DN "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (28) files: Performing unfiltered search in "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (28) files: Waiting for search result... (28) files: Group DN "cn=webupload,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "webupload" (28) files: Processing memberOf value "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan" as a DN (28) files: Resolving group DN "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan" to group name (28) files: Performing unfiltered search in "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan", scope "base" (28) files: Waiting for search result... (28) files: Group DN "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan" resolves to name "allusers" (28) files: User found in group "allusers". Comparison between membership: name (resolved from DN "cn=allusers,ou=Groups,ou=Accounts,dc=system,dc=lan"), check: name rlm_ldap (ldap): Released connection (2) (28) [files] = noop rlm_ldap (ldap): Reserved connection (3) (28) ldap: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (28) ldap: --> (uid=test1) (28) ldap: Performing search in "dc=system,dc=lan" with filter "(uid=test1)", scope "sub" (28) ldap: Waiting for search result... (28) ldap: User object found at DN "cn=test1 test1,ou=Users,ou=Accounts,dc=system,dc=lan" (28) ldap: Processing user attributes (28) ldap: control:Password-With-Header += '{sha}tESsBmE/yNY3lb6a0L6vVQEZNqw=' rlm_ldap (ldap): Released connection (3) (28) [ldap] = updated (28) [expiration] = noop (28) [logintime] = noop (28) pap: Converted: &control:Password-With-Header -> &control:SHA1-Password (28) pap: Removing &control:Password-With-Header (28) pap: Normalizing SHA1-Password from base64 encoding, 28 bytes -> 20 bytes (28) pap: WARNING: Auth-Type already set. Not setting to PAP (28) [pap] = noop (28) } # authorize = updated (28) Found Auth-Type = eap (28) # Executing group from file /etc/raddb/sites-enabled/inner-tunnel (28) authenticate { (28) eap: Expiring EAP session with state 0x67f4154866fc0fc7 (28) eap: Finished EAP session with state 0x67f4154866fc0fc7 (28) eap: Previous EAP request found for state 0x67f4154866fc0fc7, released from the list (28) eap: Peer sent packet with method EAP MSCHAPv2 (26) (28) eap: Calling submodule eap_mschapv2 to process data (28) eap: Sending EAP Success (code 3) ID 8 length 4 (28) eap: Freeing handler (28) [eap] = ok (28) } # authenticate = ok (28) # Executing section post-auth from file /etc/raddb/sites-enabled/inner-tunnel (28) post-auth { (28) if (0) { (28) if (0) -> FALSE (28) } # post-auth = noop (28) } # server inner-tunnel (28) Virtual server sending reply (28) MS-MPPE-Encryption-Policy = Encryption-Allowed (28) MS-MPPE-Encryption-Types = RC4-40or128-bit-Allowed (28) MS-MPPE-Send-Key = 0xfb5f52a89ab44a864d241d4b18249347 (28) MS-MPPE-Recv-Key = 0xda830131fe0600676623f4fe3bbd9685 (28) EAP-Message = 0x03080004 (28) Message-Authenticator = 0x00000000000000000000000000000000 (28) Stripped-User-Name = "test1" (28) eap_peap: Got tunneled reply code 2 (28) eap_peap: MS-MPPE-Encryption-Policy = Encryption-Allowed (28) eap_peap: MS-MPPE-Encryption-Types = RC4-40or128-bit-Allowed (28) eap_peap: MS-MPPE-Send-Key = 0xfb5f52a89ab44a864d241d4b18249347 (28) eap_peap: MS-MPPE-Recv-Key = 0xda830131fe0600676623f4fe3bbd9685 (28) eap_peap: EAP-Message = 0x03080004 (28) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (28) eap_peap: Stripped-User-Name = "test1" (28) eap_peap: Got tunneled reply RADIUS code 2 (28) eap_peap: MS-MPPE-Encryption-Policy = Encryption-Allowed (28) eap_peap: MS-MPPE-Encryption-Types = RC4-40or128-bit-Allowed (28) eap_peap: MS-MPPE-Send-Key = 0xfb5f52a89ab44a864d241d4b18249347 (28) eap_peap: MS-MPPE-Recv-Key = 0xda830131fe0600676623f4fe3bbd9685 (28) eap_peap: EAP-Message = 0x03080004 (28) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (28) eap_peap: Stripped-User-Name = "test1" (28) eap_peap: Tunneled authentication was successful (28) eap_peap: SUCCESS (28) eap: Sending EAP Request (code 1) ID 9 length 46 (28) eap: EAP session adding &reply:State = 0xfa6d51bcf2644896 (28) [eap] = handled (28) } # authenticate = handled (28) Using Post-Auth-Type Challenge (28) # Executing group from file /etc/raddb/sites-enabled/default (28) Challenge { ... } # empty sub-section is ignored (28) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (28) EAP-Message = 0x0109002e190017030300239fc5de61f40ef795ba8f693d2d93d08ada2e3c4dc8cdf1c2eac7662be4b2d7d3a09444 (28) Message-Authenticator = 0x00000000000000000000000000000000 (28) State = 0xfa6d51bcf264489698062bca06912e67 (28) Finished request Waking up in 4.9 seconds. (28) Cleaning up request packet ID 0 with timestamp +53 (29) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 189 (29) User-Name = "CLEARSYSTEM\\test1" (29) NAS-IP-Address = 172.22.22.254 (29) Called-Station-Id = "001601dfe596" (29) Calling-Station-Id = "74da38d41a8b" (29) NAS-Identifier = "001601dfe596" (29) NAS-Port = 5 (29) Framed-MTU = 1400 (29) State = 0xfa6d51bcf264489698062bca06912e67 (29) NAS-Port-Type = Wireless-802.11 (29) EAP-Message = 0x0209002e190017030300230000000000000004471af753e3bf22745065af3a198931d3ee8a9faeb2d337841e44a2 (29) Message-Authenticator = 0x75b133c737e069f2748c6b5b9222a581 (29) session-state: No cached attributes (29) # Executing section authorize from file /etc/raddb/sites-enabled/default (29) authorize { (29) policy filter_username { (29) if (&User-Name) { (29) if (&User-Name) -> TRUE (29) if (&User-Name) { (29) if (&User-Name =~ / /) { (29) if (&User-Name =~ / /) -> FALSE (29) if (&User-Name =~ /@[^@]*@/ ) { (29) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (29) if (&User-Name =~ /\.\./ ) { (29) if (&User-Name =~ /\.\./ ) -> FALSE (29) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (29) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (29) if (&User-Name =~ /\.$/) { (29) if (&User-Name =~ /\.$/) -> FALSE (29) if (&User-Name =~ /(a)\./) { (29) if (&User-Name =~ /(a)\./) -> FALSE (29) } # if (&User-Name) = notfound (29) } # policy filter_username = notfound (29) [preprocess] = ok (29) [chap] = noop (29) [mschap] = noop (29) [digest] = noop (29) suffix: Checking for suffix after "@" (29) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (29) suffix: No such realm "NULL" (29) [suffix] = noop (29) ntdomain: Checking for prefix before "\" (29) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (29) ntdomain: Found realm "CLEARSYSTEM" (29) ntdomain: Adding Stripped-User-Name = "test1" (29) ntdomain: Adding Realm = "CLEARSYSTEM" (29) ntdomain: Authentication realm is LOCAL (29) [ntdomain] = ok (29) eap: Peer sent EAP Response (code 2) ID 9 length 46 (29) eap: Continuing tunnel setup (29) [eap] = ok (29) } # authorize = ok (29) Found Auth-Type = eap (29) # Executing group from file /etc/raddb/sites-enabled/default (29) authenticate { (29) eap: Expiring EAP session with state 0xfa6d51bcf2644896 (29) eap: Finished EAP session with state 0xfa6d51bcf2644896 (29) eap: Previous EAP request found for state 0xfa6d51bcf2644896, released from the list (29) eap: Peer sent packet with method EAP PEAP (25) (29) eap: Calling submodule eap_peap to process data (29) eap_peap: Continuing EAP-TLS (29) eap_peap: [eaptls verify] = ok (29) eap_peap: Done initial handshake (29) eap_peap: [eaptls process] = ok (29) eap_peap: Session established. Decoding tunneled attributes (29) eap_peap: PEAP state send tlv success (29) eap_peap: Received EAP-TLV response (29) eap_peap: Success (29) eap: Sending EAP Success (code 3) ID 9 length 4 (29) eap: Freeing handler (29) [eap] = ok (29) } # authenticate = ok (29) # Executing section post-auth from file /etc/raddb/sites-enabled/default (29) post-auth { (29) update { (29) No attributes updated (29) } # update = noop (29) [exec] = noop (29) policy remove_reply_message_if_eap { (29) if (&reply:EAP-Message && &reply:Reply-Message) { (29) if (&reply:EAP-Message && &reply:Reply-Message) -> FALSE (29) else { (29) [noop] = noop (29) } # else = noop (29) } # policy remove_reply_message_if_eap = noop (29) } # post-auth = noop (29) Sent Access-Accept Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (29) MS-MPPE-Recv-Key = 0x3a2a679722b005acbb715114d8a3916f36531e4efb83c3158fb73a7e0d95a8cd (29) MS-MPPE-Send-Key = 0x73e2a159504c68f4b2a9b09c2cd3eda884da46f07bb478c2f637de7986d02c05 (29) EAP-Message = 0x03090004 (29) Message-Authenticator = 0x00000000000000000000000000000000 (29) Finished request Waking up in 4.9 seconds. (29) Cleaning up request packet ID 0 with timestamp +53 Ready to process requests (30) Received Access-Request Id 0 from 172.22.22.254:2049 to 172.22.22.1:1812 length 147 (30) User-Name = "CLEARSYSTEM\\test1" (30) NAS-IP-Address = 172.22.22.254 (30) Called-Station-Id = "001601dfe596" (30) Calling-Station-Id = "74da38d41a8b" (30) NAS-Identifier = "001601dfe596" (30) NAS-Port = 5 (30) Framed-MTU = 1400 (30) NAS-Port-Type = Wireless-802.11 (30) EAP-Message = 0x0200001601434c45415253595354454d5c7465737431 (30) Message-Authenticator = 0x26a6a6e06a663a4348a73e61f6370656 (30) # Executing section authorize from file /etc/raddb/sites-enabled/default (30) authorize { (30) policy filter_username { (30) if (&User-Name) { (30) if (&User-Name) -> TRUE (30) if (&User-Name) { (30) if (&User-Name =~ / /) { (30) if (&User-Name =~ / /) -> FALSE (30) if (&User-Name =~ /@[^@]*@/ ) { (30) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (30) if (&User-Name =~ /\.\./ ) { (30) if (&User-Name =~ /\.\./ ) -> FALSE (30) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (30) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (30) if (&User-Name =~ /\.$/) { (30) if (&User-Name =~ /\.$/) -> FALSE (30) if (&User-Name =~ /(a)\./) { (30) if (&User-Name =~ /(a)\./) -> FALSE (30) } # if (&User-Name) = notfound (30) } # policy filter_username = notfound (30) [preprocess] = ok (30) [chap] = noop (30) [mschap] = noop (30) [digest] = noop (30) suffix: Checking for suffix after "@" (30) suffix: No '@' in User-Name = "CLEARSYSTEM\test1", looking up realm NULL (30) suffix: No such realm "NULL" (30) [suffix] = noop (30) ntdomain: Checking for prefix before "\" (30) ntdomain: Looking up realm "CLEARSYSTEM" for User-Name = "CLEARSYSTEM\test1" (30) ntdomain: Found realm "CLEARSYSTEM" (30) ntdomain: Adding Stripped-User-Name = "test1" (30) ntdomain: Adding Realm = "CLEARSYSTEM" (30) ntdomain: Authentication realm is LOCAL (30) [ntdomain] = ok (30) eap: Peer sent EAP Response (code 2) ID 0 length 22 (30) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize (30) [eap] = ok (30) } # authorize = ok (30) Found Auth-Type = eap (30) # Executing group from file /etc/raddb/sites-enabled/default (30) authenticate { (30) eap: Peer sent packet with method EAP Identity (1) (30) eap: Calling submodule eap_peap to process data (30) eap_peap: Initiating new EAP-TLS session (30) eap_peap: [eaptls start] = request (30) eap: Sending EAP Request (code 1) ID 1 length 6 (30) eap: EAP session adding &reply:State = 0x436131c543602893 (30) [eap] = handled (30) } # authenticate = handled (30) Using Post-Auth-Type Challenge (30) # Executing group from file /etc/raddb/sites-enabled/default (30) Challenge { ... } # empty sub-section is ignored (30) Sent Access-Challenge Id 0 from 172.22.22.1:1812 to 172.22.22.254:2049 length 0 (30) EAP-Message = 0x010100061920 (30) Message-Authenticator = 0x00000000000000000000000000000000 (30) State = 0x436131c543602893bb7dfeada35c18c4 (30) Finished request Waking up in 4.9 seconds. I'm afraid I don't see what is going wrong and any pointers would be welcome. Thanks, Nick

3 14

Question about my client freeradius
by Nathan MARTIN 16 May '18

16 May '18

> Hello, > > I am setting up a captive portal with freeradius and I have a question : > > How can I set up a client configuration ? Is it possible to have > documentations please ? > > I installed radius server on my server OVH and now I would like to > push a landing page from a raspberry pi (client config). > > Best regards. > > > -- > Nathan MARTIN > CTO > > www.urbik.fr > Twitter - Follow us @urbik_io > > ÜRBIK est une start-up soutenue par > Le Louvre Lens Vallée -- Nathan MARTIN CTO www.urbik.fr Twitter - Follow us @urbik_io ÜRBIK est une start-up soutenue par Le Louvre Lens Vallée

2 1

Bind to ldap using end-users credentials
by Giorgos Tsirkas 16 May '18

16 May '18

Hello, I have a question.... Is there a way, when end-user trying to connect with ldap credentials, freeradius pass them and bind the ldap server? Thank you!

2 1

ignoring request from unknown client 127.0.0.1, although it is correctly defined in SQL and loaded on startup
by Radim ROŠKA 15 May '18

15 May '18

Hello everybody, My goal is to use SQL as backend for FREERADIUS. That includes definition of NAS. I'm fighting with it for several hours. All was working ok with using clients.conf configuration file. I believe I have read all posts in the forums slightly related to this...yet not sure why its still not working. I need to have more detailed debugging that would show, based on what RADIUS decides that those clients are unknown, even though its actually correctly added during startup (as it seems). Virtual server is configured correctly also I would say... I'm using: * OS : Ubuntu 17.10 * FreeRADIUS Version 3.0.15 * Mysql - 5.7.21-0ubuntu0.17.10.1 What I did: * I doublechecked that I followed guide here to the letter: * https://wiki.freeradius.org/guide/sql-howto * Commented out clients.conf => I want to use ONLY SQL * Add "sql" into configuration of virtual server "default" in section authorize * In mods-enable/sql set read_clients to yes, client_table= "nas" * Etc... But from some reason, althougth the NAS is added as it seems correctly - freeradius is still ignoring the requests...Please see below relevant details portal@portal:/var/log/freeradius$ sudo freeradius -X FreeRADIUS Version 3.0.15 Copyright (C) 1999-2017 The FreeRADIUS server project and contributors There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE You may redistribute copies of FreeRADIUS under the terms of the GNU General Public License For more information about these matters, see the file named COPYRIGHT Starting - reading configuration files ... . . . . . rlm_sql_mysql: Starting connect to MySQL server rlm_sql_mysql: Connected to database 'radius' on Localhost via UNIX socket, server version 5.7.21-0ubuntu0.17.10.1, protocol version 10 rlm_sql (sql): Processing generate_sql_clients rlm_sql (sql) in generate_sql_clients: query is SELECT id, nasname, shortname, type, secret, server FROM nas rlm_sql (sql): Reserved connection (0) rlm_sql (sql): Executing select query: SELECT id, nasname, shortname, type, secret, server FROM nas rlm_sql (sql): Adding client 10.0.0.16 (test) to default clients list rlm_sql (10.0.0.16): Client "test" (sql) added rlm_sql (sql): Adding client 127.0.0.1 (test123) to default clients list rlm_sql (127.0.0.1): Client "test123" (sql) added rlm_sql (sql): Released connection (0) . . . . Listening on command file /var/run/freeradius/freeradius.sock Listening on auth address 127.0.0.1 port 18120 bound to server inner-tunnel Listening on auth address * port 1812 bound to server default Listening on acct address * port 1813 bound to server default Listening on auth address :: port 1812 bound to server default Listening on acct address :: port 1813 bound to server default Listening on proxy address * port 37485 Listening on proxy address :: port 36997 Ready to process requests mysql> select * from nas; +----+-----------+-----------+-------+-------+-----------+---------+-----------+---------------+---------+ | id | nasname | shortname | type | ports | secret | server | community | description | version | +----+-----------+-----------+-------+-------+-----------+---------+-----------+---------------+---------+ | 2 | 10.0.0.16 | test | 1 | 62470 | radius-pw | default | community | 1 | 4 | | 3 | 127.0.0.1 | test123 | other | NULL | test | default | NULL | RADIUS Client | NULL | +----+-----------+-----------+-------+-------+-----------+---------+-----------+---------------+---------+ radmin> show client list 10.0.0.16 127.0.0.1 root@portal:/etc/freeradius/3.0/sites-enabled# radtest test test 127.0.0.1 1812 test Sent Access-Request Id 176 from 0.0.0.0:46822 to 127.0.0.1:1812 length 74 User-Name = "test" User-Password = "test" NAS-IP-Address = 10.0.1.16 NAS-Port = 1812 Message-Authenticator = 0x00 Cleartext-Password = "test" Freeradius -X ... Ready to process requests Ignoring request to auth address * port 1812 bound to server default from unknown client 127.0.0.1 port 46822 proto udp Ready to process requests Same happens when I send radius auth from network device 10.0.0.16 Ignoring request to auth address * port 1812 bound to server default from unknown client 10.0.0.16 port 62470 proto udp Ready to process requests radmin> show module config sql sql { driver = "rlm_sql_mysql" server = "localhost" port = 3306 login = "radius" password = "xxx" radius_db = "radius" read_groups = yes read_profiles = yes readclients = yes read_clients = yes deletestalesessions = yes delete_stale_sessions = yes sql_user_name = "%{User-Name}" logfile = default_user_profile = "" nas_query = "SELECT id, nasname, shortname, type, secret, server FROM nas" client_query = "SELECT id, nasname, shortname, type, secret, server FROM nas" open_query = authorize_check_query = "SELECT id, username, attribute, value, op FROM radcheck WHERE username = '%{SQL-User-Name}' ORDER BY id" authorize_reply_query = "SELECT id, username, attribute, value, op FROM radreply WHERE username = '%{SQL-User-Name}' ORDER BY id" authorize_group_check_query = "SELECT id, groupname, attribute, Value, op FROM radgroupcheck WHERE groupname = '%{SQL-Group}' ORDER BY id" authorize_group_reply_query = "SELECT id, groupname, attribute, value, op FROM radgroupreply WHERE groupname = '%{SQL-Group}' ORDER BY id" group_membership_query = "SELECT groupname FROM radusergroup WHERE username = '%{SQL-User-Name}' ORDER BY priority" simul_count_query = "SELECT COUNT(*) FROM radacct WHERE username = '%{SQL-User-Name}' AND acctstoptime IS NULL" simul_verify_query = "SELECT radacctid, acctsessionid, username, nasipaddress, nasportid, framedipaddress, callingstationid, framedprotocol FROM radacct WHERE username = '%{SQL-User-Name}' AND acctstoptime IS NULL" safe-characters = "@abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789.-_: /" safe_characters = "@abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789.-_: /" query_timeout = 0 accounting = ? post-auth = ? }

4 9