April 2015 - Freeradius-Users - lists.freeradius.org

Error
by sandy.napoles＠eccmg.cupet.cu 14 Apr '15

14 Apr '15

I wanna install freeradius 3.0.7 when I run radiusd -x Debugger not attached Refusing to start with libssl version OpenSSL 1.0.1e 11 Feb 2013 0x1000105f (1.0.1e release) (in range 1.0.1 dev - 1.0.1f release) Security advisory CVE-2014-0160 (Heartbleed) For more information see http://heartbleed.com Once you have verified libssl has been correctly patched, set security.allow_vulnerable_openssl = 'CVE-2014-0160'

6 5

Re: FreeRadius2 issue when deployed as proxy for EAP-TLS
by Matthew Newton 14 Apr '15

14 Apr '15

On Tue, Apr 14, 2015 at 12:57:48PM +0000, Muhammad Faisal wrote: > Do excuse me for sending wrong file. I have attached a correct file within now. That's much better, thanks. If you read that output, you'll notice the packet that was proxied on is identical to the packet that was received. Therefore FreeRADIUS is doing its job correctly. You need to investigate what is broken on your other RADIUS server. It either doesn't understand eap, or doesn't have eap configured correctly. Matthew > Ready to process requests. > rad_recv: Access-Request packet from host 192.168.52.75 port 10034, id=71, length=235 > User-Name = "001C1127E021(a)setuptest.com" > NAS-IP-Address = 192.168.52.75 > Calling-Station-Id = "001c1127e021" > NAS-Identifier = "HW-WASN" > Event-Timestamp = "Apr 14 2015 17:10:55 PKT" > EAP-Message = 0x0217001f01303031433131323745303231407175626565746573742e636f6d > WiMAX-Release = "1.1" > WiMAX-Accounting-Capabilities = Flow-Based > WiMAX-Hotlining-Capabilities = Hotline-Profile-Id > WiMAX-Idle-Mode-Notification-Cap = Supported > WiMAX-Attr-1281 = 0x01 > BS-Id = 0x303030303037303031313130 > WiMAX-GMT-Timezone-offset = 18000 > NAS-Port-Type = Wireless-802.16 > WiMAX-Available-In-Client = 99 > Service-Type = Framed-User > Chargeable-User-Identity = "\000\000" > Message-Authenticator = 0x1a5e73e60c133a6586d7adb34776c7c5 > # Executing section authorize from file /etc/raddb/sites-enabled/default ... > +- entering group pre-proxy {...} > [pre_proxy_log] expand: /var/log/radius/radacct/%{Client-IP-Address}/pre-proxy-detail-%Y%m%d -> /var/log/radius/radacct/192.168.52.75/pre-proxy-detail-20150414 > [pre_proxy_log] /var/log/radius/radacct/%{Client-IP-Address}/pre-proxy-detail-%Y%m%d expands to /var/log/radius/radacct/192.168.52.75/pre-proxy-detail-20150414 > [pre_proxy_log] expand: %t -> Tue Apr 14 17:20:23 2015 > ++[pre_proxy_log] returns ok > Sending Access-Request of id 66 to 192.168.51.6 port 1812 > User-Name = "001C1127E021(a)setuptest.com" > NAS-IP-Address = 192.168.52.75 > Calling-Station-Id = "001c1127e021" > NAS-Identifier = "HW-WASN" > Event-Timestamp = "Apr 14 2015 17:10:55 PKT" > EAP-Message = 0x0217001f01303031433131323745303231407175626565746573742e636f6d > WiMAX-Release = "1.1" > WiMAX-Accounting-Capabilities = Flow-Based > WiMAX-Hotlining-Capabilities = Hotline-Profile-Id > WiMAX-Idle-Mode-Notification-Cap = Supported > WiMAX-Attr-1281 = 0x01 > BS-Id = 0x303030303037303031313130 > WiMAX-GMT-Timezone-offset = 18000 > NAS-Port-Type = Wireless-802.16 > WiMAX-Available-In-Client = 99 > Service-Type = Framed-User > Chargeable-User-Identity = "\000\000" > Message-Authenticator = 0x00000000000000000000000000000000 > Proxy-State = 0x3731 > Proxying request 0 to home server 192.168.51.6 port 1812 > Sending Access-Request of id 66 to 192.168.51.6 port 1812 > User-Name = "001C1127E021(a)setuptest.com" > NAS-IP-Address = 192.168.52.75 > Calling-Station-Id = "001c1127e021" > NAS-Identifier = "HW-WASN" > Event-Timestamp = "Apr 14 2015 17:10:55 PKT" > EAP-Message = 0x0217001f01303031433131323745303231407175626565746573742e636f6d > WiMAX-Release = "1.1" > WiMAX-Capability = 0x0105312e31020302030301040301 > WiMAX-Accounting-Capabilities = Flow-Based > WiMAX-Hotlining-Capabilities = Hotline-Profile-Id > WiMAX-Idle-Mode-Notification-Cap = Supported > WiMAX-Attr-1281 = 0x01 > BS-Id = 0x303030303037303031313130 > WiMAX-GMT-Timezone-offset = 18000 > NAS-Port-Type = Wireless-802.16 > WiMAX-Available-In-Client = 99 > PPAC = 0x010600000063 > Service-Type = Framed-User > Chargeable-User-Identity = "\000\000" > Message-Authenticator = 0x00000000000000000000000000000000 > Proxy-State = 0x3731 > Going to the next request > Waking up in 0.9 seconds. > rad_recv: Access-Reject packet from host 192.168.51.6 port 1812, id=66, length=38 > Reply-Message = "Invalid Password" -- Matthew Newton, Ph.D. <mcn4(a)le.ac.uk> Systems Specialist, Infrastructure Services, I.T. Services, University of Leicester, Leicester LE1 7RH, United Kingdom For IT help contact helpdesk extn. 2253, <ithelp(a)le.ac.uk>

2 1

FreeRadius2 issue when deployed as proxy for EAP-TLS
by Muhammad Faisal 14 Apr '15

14 Apr '15

Hi,We are trying to setup a test bench to test the freeRadius in proxy mode for eap-TLS requests. We are seeing the host is sending request but the proxy is not seding the correct access request to home server. We are seeing from the logs that the proxy request to home server is treated as Authentication type basic instead of EAP-TLS. Regards,Muhammad Faisal. This message contains privileged and confidential information intended only for the use of the addressee named above. If you are not the intended recipient of this message, you must not disseminate, copy, or take any action in reliance on it.If you have received this message in error, please notify the sender immediately. No responsibility or liability is accepted by the writer, or any company associated with the writer, as to the accuracy of the information contained herein, or from any loss arising from reliance on it. Copyright and database rights exist in this document and to any attachment. Although we operate anti-virus programs, we do not accept responsibility for any damage whatsoever that is caused by viruses being passed.

3 4

Issues getting SLES11 FreeRadius working with eDirectory
by Brian Boere 14 Apr '15

14 Apr '15

We have a SLES10 SP4 server with freeradius (version 1.1.7-21.8.39 according to YAST2) working with eDirectory. We have it set so that if a user is not a member of an eDirectory group, they cannot get connected to the wireless AP. We are wanting to add a second wireless network and have authentication work if the NAS-ID and eDirectory groups are a specific match. We have done some reading and found that it is supposed to be easier to accomplish this using FreeRadius version 2. So we now have a SLES11SP3 server configured with Freeradius (version 2.1.1-7.18.1 according to YAST2). When using radtest, the LDAP requests all seem to go through properly. (if not a member of the edir group, get a message that the user is not allowed to connect, if member of the edir group, get a successful connection message). When we try to connect with a wireless device, we get prompted for the username/password and get the option to accept the security certificates. The device will not connect. We have rebuilt the freeradius on the SLES10 server several times and can get it to work each time without issues. We have made the same configuration changes on the SLES11 server, and cannot get it to connect. (we are obviously missing something, but cannot find it) This is the radiusd -X log: FreeRADIUS Version 2.1.1, for host x86_64-suse-linux-gnu, built on Feb 28 2014 at 23:17:30 Copyright (C) 1999-2008 The FreeRADIUS server project and contributors. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. You may redistribute copies of FreeRADIUS under the terms of the GNU General Public License v2. Starting - reading configuration files ... including configuration file /etc/raddb/radiusd.conf including configuration file /etc/raddb/proxy.conf including configuration file /etc/raddb/clients.conf including files in directory /etc/raddb/modules/ including configuration file /etc/raddb/modules/detail.log including configuration file /etc/raddb/modules/krb5 including configuration file /etc/raddb/modules/passwd including configuration file /etc/raddb/modules/digest including configuration file /etc/raddb/modules/policy including configuration file /etc/raddb/modules/attr_filter including configuration file /etc/raddb/modules/echo including configuration file /etc/raddb/modules/radutmp including configuration file /etc/raddb/modules/ldap including configuration file /etc/raddb/modules/counter including configuration file /etc/raddb/modules/pam including configuration file /etc/raddb/modules/realm including configuration file /etc/raddb/modules/preprocess including configuration file /etc/raddb/modules/always including configuration file /etc/raddb/modules/expr including configuration file /etc/raddb/modules/unix including configuration file /etc/raddb/modules/attr_rewrite including configuration file /etc/raddb/modules/expiration including configuration file /etc/raddb/modules/mac2vlan including configuration file /etc/raddb/modules/mac2ip including configuration file /etc/raddb/modules/etc_group including configuration file /etc/raddb/modules/pap including configuration file /etc/raddb/modules/chap including configuration file /etc/raddb/modules/sql_log including configuration file /etc/raddb/modules/smbpasswd including configuration file /etc/raddb/modules/exec including configuration file /etc/raddb/modules/logintime including configuration file /etc/raddb/modules/linelog including configuration file /etc/raddb/modules/mschap including configuration file /etc/raddb/modules/acct_unique including configuration file /etc/raddb/modules/inner-eap including configuration file /etc/raddb/modules/detail including configuration file /etc/raddb/modules/wimax including configuration file /etc/raddb/modules/files including configuration file /etc/raddb/modules/detail.example.com including configuration file /etc/raddb/modules/ippool including configuration file /etc/raddb/modules/sradutmp including configuration file /etc/raddb/modules/checkval including configuration file /etc/raddb/eap.conf including configuration file /etc/raddb/sql.conf including configuration file /etc/raddb/sql/mysql/dialup.conf including configuration file /etc/raddb/sql/mysql/counter.conf including configuration file /etc/raddb/policy.conf including files in directory /etc/raddb/sites-enabled/ including configuration file /etc/raddb/sites-enabled/default including configuration file /etc/raddb/sites-enabled/inner-tunnel group = radiusd user = radiusd including dictionary file /etc/raddb/dictionary main { prefix = "/usr" localstatedir = "/var" logdir = "/var/log/radius" libdir = "/usr/lib64/freeradius" radacctdir = "/var/log/radius/radacct" hostname_lookups = no max_request_time = 30 cleanup_delay = 5 max_requests = 1024 allow_core_dumps = no pidfile = "/var/run/radiusd/radiusd.pid" checkrad = "/usr/sbin/checkrad" debug_level = 0 proxy_requests = yes log { stripped_names = no auth = no auth_badpass = no auth_goodpass = no } security { max_attributes = 200 reject_delay = 1 status_server = yes } } client localhost { ipaddr = 127.0.0.1 require_message_authenticator = no secret = "testing123" nastype = "other" } client 192.168.1.53 { require_message_authenticator = no secret = "sophos123" shortname = "RadiusServer" } client 192.168.1.1 { require_message_authenticator = no secret = "sophos123" shortname = "SophosAppliance" } radiusd: #### Loading Realms and Home Servers #### proxy server { retry_delay = 5 retry_count = 3 default_fallback = no dead_time = 120 wake_all_if_all_dead = no } home_server localhost { ipaddr = 127.0.0.1 port = 1812 type = "auth" secret = "testing123" response_window = 20 max_outstanding = 65536 zombie_period = 40 status_check = "status-server" ping_interval = 30 check_interval = 30 num_answers_to_alive = 3 num_pings_to_alive = 3 revive_interval = 120 status_check_timeout = 4 } home_server_pool my_auth_failover { type = fail-over home_server = localhost } realm example.com { auth_pool = my_auth_failover } realm LOCAL { } radiusd: #### Instantiating modules #### instantiate { Module: Linked to module rlm_exec Module: Instantiating exec exec { wait = no input_pairs = "request" shell_escape = yes } Module: Linked to module rlm_expr Module: Instantiating expr Module: Linked to module rlm_expiration Module: Instantiating expiration expiration { reply-message = "Password Has Expired " } Module: Linked to module rlm_logintime Module: Instantiating logintime logintime { reply-message = "You are calling outside your allowed timespan " minimum-timeout = 60 } } radiusd: #### Loading Virtual Servers #### server inner-tunnel { modules { Module: Checking authenticate {...} for more modules to load Module: Linked to module rlm_pap Module: Instantiating pap pap { encryption_scheme = "auto" auto_header = no } Module: Linked to module rlm_chap Module: Instantiating chap Module: Linked to module rlm_mschap Module: Instantiating mschap mschap { use_mppe = yes require_encryption = no require_strong = no with_ntdomain_hack = no } Module: Linked to module rlm_unix Module: Instantiating unix unix { radwtmp = "/var/log/radius/radwtmp" } Module: Linked to module rlm_eap Module: Instantiating eap eap { default_eap_type = "peap" timer_expire = 60 ignore_unknown_eap_types = no cisco_accounting_username_bug = no max_sessions = 2048 } Module: Linked to sub-module rlm_eap_md5 Module: Instantiating eap-md5 Module: Linked to sub-module rlm_eap_leap Module: Instantiating eap-leap Module: Linked to sub-module rlm_eap_gtc Module: Instantiating eap-gtc gtc { challenge = "Password: " auth_type = "PAP" } Module: Linked to sub-module rlm_eap_tls Module: Instantiating eap-tls tls { rsa_key_exchange = no dh_key_exchange = yes rsa_key_length = 512 dh_key_length = 512 verify_depth = 0 pem_file_type = yes private_key_file = "/etc/raddb/certs/servercert.pem" certificate_file = "/etc/raddb/certs/servercert.pem" CA_file = "/etc/raddb/certs/rootcert.pem" private_key_password = "Donkey01" dh_file = "/etc/raddb/certs/dh" random_file = "/etc/raddb/certs/random" fragment_size = 1024 include_length = yes check_crl = no cipher_list = "DEFAULT" make_cert_command = "/etc/raddb/certs/bootstrap" cache { enable = no lifetime = 24 max_entries = 255 } } Module: Linked to sub-module rlm_eap_ttls Module: Instantiating eap-ttls ttls { default_eap_type = "md5" copy_request_to_tunnel = no use_tunneled_reply = no virtual_server = "inner-tunnel" } Module: Linked to sub-module rlm_eap_peap Module: Instantiating eap-peap peap { default_eap_type = "mschapv2" copy_request_to_tunnel = no use_tunneled_reply = no proxy_tunneled_request_as_eap = yes virtual_server = "inner-tunnel" } Module: Linked to sub-module rlm_eap_mschapv2 Module: Instantiating eap-mschapv2 mschapv2 { with_ntdomain_hack = no } Module: Checking authorize {...} for more modules to load Module: Linked to module rlm_realm Module: Instantiating suffix realm suffix { format = "suffix" delimiter = "@" ignore_default = no ignore_null = no } Module: Linked to module rlm_files Module: Instantiating files files { usersfile = "/etc/raddb/users" acctusersfile = "/etc/raddb/acct_users" preproxy_usersfile = "/etc/raddb/preproxy_users" compat = "no" } Module: Checking session {...} for more modules to load Module: Linked to module rlm_radutmp Module: Instantiating radutmp radutmp { filename = "/var/log/radius/radutmp" username = "%{User-Name}" case_sensitive = yes check_with_nas = yes perm = 384 callerid = yes } Module: Checking post-proxy {...} for more modules to load Module: Checking post-auth {...} for more modules to load Module: Linked to module rlm_attr_filter Module: Instantiating attr_filter.access_reject attr_filter attr_filter.access_reject { attrsfile = "/etc/raddb/attrs.access_reject" key = "%{User-Name}" } } } modules { Module: Checking authenticate {...} for more modules to load Module: Linked to module rlm_ldap Module: Instantiating ldap ldap { server = "192.168.1.14" port = 389 password = "chevy01" identity = "cn=brian,ou=ou,o=org" net_timeout = 1 timeout = 4 timelimit = 3 tls_mode = no start_tls = no tls_require_cert = "allow" tls { start_tls = no require_cert = "allow" } basedn = "ou=ou,o=org" filter = "(uid=%{Stripped-User-Name:-%{User-Name}})" base_filter = "(objectclass=radiusprofile)" password_attribute = "npsmPassword" auto_header = no access_attr_used_for_allow = no groupname_attribute = "cn" groupmembership_filter = "(|(&(objectClass=GroupOfNames)(member=%{check:Ldap-UserDn}))(&(objectClass=GroupOfUniqueNames)(uniquemember=%{Ldap-UserDn})))" dictionary_mapping = "/etc/raddb/ldap.attrmap" ldap_debug = 0 ldap_connections_number = 5 compare_check_items = no do_xlat = yes edir_account_policy_check = no set_auth_type = yes } rlm_ldap: Registering ldap_groupcmp for Ldap-Group rlm_ldap: Registering ldap_xlat with xlat_name ldap rlm_ldap: reading ldap<->radius mappings from file /etc/raddb/ldap.attrmap rlm_ldap: LDAP radiusCheckItem mapped to RADIUS $GENERIC$ rlm_ldap: LDAP radiusReplyItem mapped to RADIUS $GENERIC$ rlm_ldap: LDAP radiusAuthType mapped to RADIUS Auth-Type rlm_ldap: LDAP radiusSimultaneousUse mapped to RADIUS Simultaneous-Use rlm_ldap: LDAP radiusCalledStationId mapped to RADIUS Called-Station-Id rlm_ldap: LDAP radiusCallingStationId mapped to RADIUS Calling-Station-Id rlm_ldap: LDAP lmPassword mapped to RADIUS LM-Password rlm_ldap: LDAP ntPassword mapped to RADIUS NT-Password rlm_ldap: LDAP sambaLmPassword mapped to RADIUS LM-Password rlm_ldap: LDAP sambaNtPassword mapped to RADIUS NT-Password rlm_ldap: LDAP dBCSPwd mapped to RADIUS LM-Password rlm_ldap: LDAP acctFlags mapped to RADIUS SMB-Account-CTRL-TEXT rlm_ldap: LDAP radiusExpiration mapped to RADIUS Expiration rlm_ldap: LDAP radiusNASIpAddress mapped to RADIUS NAS-IP-Address rlm_ldap: LDAP radiusServiceType mapped to RADIUS Service-Type rlm_ldap: LDAP radiusFramedProtocol mapped to RADIUS Framed-Protocol rlm_ldap: LDAP radiusFramedIPAddress mapped to RADIUS Framed-IP-Address rlm_ldap: LDAP radiusFramedIPNetmask mapped to RADIUS Framed-IP-Netmask rlm_ldap: LDAP radiusFramedRoute mapped to RADIUS Framed-Route rlm_ldap: LDAP radiusFramedRouting mapped to RADIUS Framed-Routing rlm_ldap: LDAP radiusFilterId mapped to RADIUS Filter-Id rlm_ldap: LDAP radiusFramedMTU mapped to RADIUS Framed-MTU rlm_ldap: LDAP radiusFramedCompression mapped to RADIUS Framed-Compression rlm_ldap: LDAP radiusLoginIPHost mapped to RADIUS Login-IP-Host rlm_ldap: LDAP radiusLoginService mapped to RADIUS Login-Service rlm_ldap: LDAP radiusLoginTCPPort mapped to RADIUS Login-TCP-Port rlm_ldap: LDAP radiusCallbackNumber mapped to RADIUS Callback-Number rlm_ldap: LDAP radiusCallbackId mapped to RADIUS Callback-Id rlm_ldap: LDAP radiusFramedIPXNetwork mapped to RADIUS Framed-IPX-Network rlm_ldap: LDAP radiusClass mapped to RADIUS Class rlm_ldap: LDAP radiusSessionTimeout mapped to RADIUS Session-Timeout rlm_ldap: LDAP radiusIdleTimeout mapped to RADIUS Idle-Timeout rlm_ldap: LDAP radiusTerminationAction mapped to RADIUS Termination-Action rlm_ldap: LDAP radiusLoginLATService mapped to RADIUS Login-LAT-Service rlm_ldap: LDAP radiusLoginLATNode mapped to RADIUS Login-LAT-Node rlm_ldap: LDAP radiusLoginLATGroup mapped to RADIUS Login-LAT-Group rlm_ldap: LDAP radiusFramedAppleTalkLink mapped to RADIUS Framed-AppleTalk-Link rlm_ldap: LDAP radiusFramedAppleTalkNetwork mapped to RADIUS Framed-AppleTalk-Network rlm_ldap: LDAP radiusFramedAppleTalkZone mapped to RADIUS Framed-AppleTalk-Zone rlm_ldap: LDAP radiusPortLimit mapped to RADIUS Port-Limit rlm_ldap: LDAP radiusLoginLATPort mapped to RADIUS Login-LAT-Port rlm_ldap: LDAP radiusReplyMessage mapped to RADIUS Reply-Message conns: 0x7f249ba1b300 Module: Checking authorize {...} for more modules to load Module: Linked to module rlm_preprocess Module: Instantiating preprocess preprocess { huntgroups = "/etc/raddb/huntgroups" hints = "/etc/raddb/hints" with_ascend_hack = no ascend_channels_per_line = 23 with_ntdomain_hack = no with_specialix_jetstream_hack = no with_cisco_vsa_hack = no with_alvarion_vsa_hack = no } Module: Checking preacct {...} for more modules to load Module: Linked to module rlm_acct_unique Module: Instantiating acct_unique acct_unique { key = "User-Name, Acct-Session-Id, NAS-IP-Address, Client-IP-Address, NAS-Port" } Module: Checking accounting {...} for more modules to load Module: Linked to module rlm_detail Module: Instantiating detail detail { detailfile = "/var/log/radius/radacct/%{Client-IP-Address}/detail-%Y%m%d" header = "%t" detailperm = 384 dirperm = 493 locking = no log_packet_header = no } Module: Instantiating attr_filter.accounting_response attr_filter attr_filter.accounting_response { attrsfile = "/etc/raddb/attrs.accounting_response" key = "%{User-Name}" } Module: Checking session {...} for more modules to load Module: Checking post-proxy {...} for more modules to load Module: Checking post-auth {...} for more modules to load } radiusd: #### Opening IP addresses and Ports #### listen { type = "auth" ipaddr = * port = 0 } listen { type = "acct" ipaddr = * port = 0 } Listening on authentication address * port 1812 Listening on accounting address * port 1813 Listening on proxy address * port 1814 Ready to process requests. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=84, length=162 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x0201000c016d617269737361 Message-Authenticator = 0x2d290123d7e9601ba913c48682a80b59 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 1 length 12 [eap] No EAP Start, assuming it's an on-going EAP conversation ++[eap] returns updated ++[unix] returns notfound rlm_ldap: Entering ldap_groupcmp() [files] expand: ou=ou,o=org -> ou=ou,o=org [files] WARNING: Deprecated conditional expansion ":-". See "man unlang" for details [files] expand: (uid=%{Stripped-User-Name:-%{User-Name}}) -> (uid=marissa) rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: attempting LDAP reconnection rlm_ldap: (re)connect to 192.168.1.14:389, authentication 0 rlm_ldap: bind as cn=brian,ou=ou,o=org/chevy01 to 192.168.1.14:389 rlm_ldap: waiting for bind result ... rlm_ldap: Bind was successful rlm_ldap: performing search in ou=ou,o=org, with filter (uid=marissa) rlm_ldap: ldap_release_conn: Release Id: 0 [files] expand: (|(&(objectClass=GroupOfNames)(member=%{check:Ldap-UserDn}))(&(objectClass=GroupOfUniqueNames)(uniquemember=%{Ldap-UserDn}))) -> (|(&(objectClass=GroupOfNames)(member=cn\3dMarissa\2cou\3dou\2co\3dorg))(&(objectClass=GroupOfUniqueNames)(uniquemember=))) rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in cn=Corporate Wireless Network,ou=ou,o=org, with filter (|(&(objectClass=GroupOfNames)(member=cn\3dMarissa\2cou\3dou\2co\3dorg))(&(objectClass=GroupOfUniqueNames)(uniquemember=))) rlm_ldap::ldap_groupcmp: User found in group cn=Corporate Wireless Network,ou=ou,o=org rlm_ldap: ldap_release_conn: Release Id: 0 [files] users: Matched entry DEFAULT at line 3 ++[files] returns ok [ldap] performing user authorization for marissa [ldap] WARNING: Deprecated conditional expansion ":-". See "man unlang" for details [ldap] expand: (uid=%{Stripped-User-Name:-%{User-Name}}) -> (uid=marissa) [ldap] expand: ou=ou,o=org -> ou=ou,o=org rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=ou,o=org, with filter (uid=marissa) [ldap] No default NMAS login sequence [ldap] looking for check items in directory... [ldap] looking for reply items in directory... WARNING: No "known good" password was found in LDAP. Are you sure that the user is configured correctly? [ldap] user marissa authorized to use remote access rlm_ldap: ldap_release_conn: Release Id: 0 ++[ldap] returns ok ++[expiration] returns noop ++[logintime] returns noop [pap] WARNING! No "known good" password found for the user. Authentication may fail because of this. ++[pap] returns noop Found Auth-Type = EAP +- entering group authenticate {...} [eap] EAP Identity [eap] processing type tls [tls] Initiate [tls] Start returned 1 ++[eap] returns handled Sending Access-Challenge of id 84 to 192.168.1.1 port 44783 Reply-Message = "You have been authenticated" EAP-Message = 0x010200061920 Message-Authenticator = 0x00000000000000000000000000000000 State = 0xd9001cbcd902052adaeb377365c8c185 Finished request 0. Going to the next request Waking up in 4.9 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=85, length=320 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x0202009819800000008e16030100890100008503015525d4b72ee5a48517ff521fd6cf39ee30e6874ec5f58dda752e7aadedfe2fcc00004a00ffc024c023c00ac009c007c008c028c027c014c013c011c012c026c025c02ac029c005c004c002c003c00fc00ec00cc00d003d003c002f000500040035000a0067006b00330039001601000012000a00080006001700180019000b00020100 State = 0xd9001cbcd902052adaeb377365c8c185 Message-Authenticator = 0x758edab72cfda72bd82f0c28d4259c98 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 2 length 152 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS TLS Length 142 [peap] Length Included [peap] eaptls_verify returned 11 [peap] (other): before/accept initialization [peap] TLS_accept: before/accept initialization [peap] <<< TLS 1.0 Handshake [length 0089], ClientHello [peap] TLS_accept: SSLv3 read client hello A [peap] >>> TLS 1.0 Handshake [length 0031], ServerHello [peap] TLS_accept: SSLv3 write server hello A [peap] >>> TLS 1.0 Handshake [length 08e7], Certificate [peap] TLS_accept: SSLv3 write certificate A [peap] >>> TLS 1.0 Handshake [length 0004], ServerHelloDone [peap] TLS_accept: SSLv3 write server done A [peap] TLS_accept: SSLv3 flush data [peap] TLS_accept: Need to read more data: SSLv3 read client certificate A In SSL Handshake Phase In SSL Accept mode [peap] eaptls_process returned 13 [peap] EAPTLS_HANDLED ++[eap] returns handled Sending Access-Challenge of id 85 to 192.168.1.1 port 44783 EAP-Message = 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 EAP-Message = 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 EAP-Message = 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 EAP-Message = 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 EAP-Message = 0xc58044f3ddec6c0e7f82e084 Message-Authenticator = 0x00000000000000000000000000000000 State = 0xd9001cbcd803052adaeb377365c8c185 Finished request 1. Going to the next request Waking up in 4.9 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=86, length=174 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x020300061900 State = 0xd9001cbcd803052adaeb377365c8c185 Message-Authenticator = 0x3a716f65614e706af1f54a3a8174f9cc +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 3 length 6 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] Received TLS ACK [peap] ACK handshake fragment handler [peap] eaptls_verify returned 1 [peap] eaptls_process returned 13 [peap] EAPTLS_HANDLED ++[eap] returns handled Sending Access-Challenge of id 86 to 192.168.1.1 port 44783 EAP-Message = 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 EAP-Message = 0x1316596153542044656661756c7420434120286d657461293122302006092a864886f70d0109011613706f73746d617374657240626f6572652e6361301e170d3134303831323030303833345a170d3234303830393030303833345a3052310b3009060355040613025553311f301d06035504031316596153542044656661756c7420434120286d657461293122302006092a864886f70d0109011613706f73746d617374657240626f6572652e636130820122300d06092a864886f70d01010105000382010f003082010a0282010100decfc2ba9abe825287e331db7490e97d8bc3ef11d735946e2748afd6e46908fdbe81ede570ee358445911d1f EAP-Message = 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 EAP-Message = 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 EAP-Message = 0x7240626f6572652e Message-Authenticator = 0x00000000000000000000000000000000 State = 0xd9001cbcdb04052adaeb377365c8c185 Finished request 2. Going to the next request Waking up in 4.9 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=87, length=174 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x020400061900 State = 0xd9001cbcdb04052adaeb377365c8c185 Message-Authenticator = 0x44e85cf35b2652aeff56bfcd1b16c5cd +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 4 length 6 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] Received TLS ACK [peap] ACK handshake fragment handler [peap] eaptls_verify returned 1 [peap] eaptls_process returned 13 [peap] EAPTLS_HANDLED ++[eap] returns handled Sending Access-Challenge of id 87 to 192.168.1.1 port 44783 EAP-Message = 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 EAP-Message = 0xb0c10bdf7d58306a9b62f457869be27e0500f12bb5bdbf451afcd037f43bd26db19169f9fd88a6ab8f49783d3718a97908838502011a8b6cfea38002e6929816030100040e000000 Message-Authenticator = 0x00000000000000000000000000000000 State = 0xd9001cbcda05052adaeb377365c8c185 Finished request 3. Going to the next request Waking up in 4.9 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=88, length=506 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 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 EAP-Message = 0x14b7bbb48647fb9fdc5fd14e51c44d615ec192713ae3fb021403010001011603010030b5f1af276c5e2fc65e0d3cf690ac2b86b52c39a92aad5202f9eca964e1dcacd02856d7628617f4b10e7f4e68175e3599 State = 0xd9001cbcda05052adaeb377365c8c185 Message-Authenticator = 0x073c9d8ac8cc325748672451ed420003 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 5 length 253 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS TLS Length 326 [peap] Length Included [peap] eaptls_verify returned 11 [peap] <<< TLS 1.0 Handshake [length 0106], ClientKeyExchange [peap] TLS_accept: SSLv3 read client key exchange A [peap] <<< TLS 1.0 ChangeCipherSpec [length 0001] [peap] <<< TLS 1.0 Handshake [length 0010], Finished [peap] TLS_accept: SSLv3 read finished A [peap] >>> TLS 1.0 ChangeCipherSpec [length 0001] [peap] TLS_accept: SSLv3 write change cipher spec A [peap] >>> TLS 1.0 Handshake [length 0010], Finished [peap] TLS_accept: SSLv3 write finished A [peap] TLS_accept: SSLv3 flush data [peap] (other): SSL negotiation finished successfully SSL Connection Established [peap] eaptls_process returned 13 [peap] EAPTLS_HANDLED ++[eap] returns handled Sending Access-Challenge of id 88 to 192.168.1.1 port 44783 EAP-Message = 0x01060041190014030100010116030100304fb3adbe14355ec984ad62752e83470eff341ddf8cd09b7f24f9af73977020a400b89fd96b88d3cebe11c4e853c8d67a Message-Authenticator = 0x00000000000000000000000000000000 State = 0xd9001cbcdd06052adaeb377365c8c185 Finished request 4. Going to the next request Waking up in 4.8 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=89, length=174 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x020600061900 State = 0xd9001cbcdd06052adaeb377365c8c185 Message-Authenticator = 0x4887f74174bf5b3756f3a3d023191da0 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 6 length 6 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] Received TLS ACK [peap] ACK handshake is finished [peap] eaptls_verify returned 3 [peap] eaptls_process returned 3 [peap] EAPTLS_SUCCESS ++[eap] returns handled Sending Access-Challenge of id 89 to 192.168.1.1 port 44783 EAP-Message = 0x0107002b190017030100206b27502b3a646f9fdb694ce16590e60c23995ea191e5a23adcb4b2659fdf3cf6 Message-Authenticator = 0x00000000000000000000000000000000 State = 0xd9001cbcdc07052adaeb377365c8c185 Finished request 5. Going to the next request Waking up in 4.8 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=90, length=211 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x0207002b19001703010020d55d342c1b1bd4c455b0062ad55ff3f7ae5ad1db215f7e324ea3d8ed7ed58daa State = 0xd9001cbcdc07052adaeb377365c8c185 Message-Authenticator = 0x10d5b34de8fb14107b2dccab6e94272e +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 7 length 43 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] eaptls_verify returned 7 [peap] Done initial handshake [peap] eaptls_process returned 7 [peap] EAPTLS_OK [peap] Session established. Decoding tunneled attributes. [peap] Identity - marissa [peap] Got tunnled request EAP-Message = 0x0207000c016d617269737361 server (null) { PEAP: Got tunneled identity of marissa PEAP: Setting default EAP type for tunneled EAP session. PEAP: Setting User-Name to marissa Sending tunneled request EAP-Message = 0x0207000c016d617269737361 FreeRADIUS-Proxied-To = 127.0.0.1 User-Name = "marissa" server inner-tunnel { +- entering group authorize {...} ++[chap] returns noop ++[mschap] returns noop ++[unix] returns notfound [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop ++[control] returns noop [eap] EAP packet type response id 7 length 12 [eap] No EAP Start, assuming it's an on-going EAP conversation ++[eap] returns updated rlm_ldap: Entering ldap_groupcmp() [files] expand: ou=ou,o=org -> ou=ou,o=org [files] WARNING: Deprecated conditional expansion ":-". See "man unlang" for details [files] expand: (uid=%{Stripped-User-Name:-%{User-Name}}) -> (uid=marissa) rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=ou,o=org, with filter (uid=marissa) rlm_ldap: ldap_release_conn: Release Id: 0 [files] expand: (|(&(objectClass=GroupOfNames)(member=%{check:Ldap-UserDn}))(&(objectClass=GroupOfUniqueNames)(uniquemember=%{Ldap-UserDn}))) -> (|(&(objectClass=GroupOfNames)(member=cn\3dMarissa\2cou\3dou\2co\3dorg))(&(objectClass=GroupOfUniqueNames)(uniquemember=))) rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in cn=Corporate Wireless Network,ou=ou,o=org, with filter (|(&(objectClass=GroupOfNames)(member=cn\3dMarissa\2cou\3dou\2co\3dorg))(&(objectClass=GroupOfUniqueNames)(uniquemember=))) rlm_ldap::ldap_groupcmp: User found in group cn=Corporate Wireless Network,ou=ou,o=org rlm_ldap: ldap_release_conn: Release Id: 0 [files] users: Matched entry DEFAULT at line 3 ++[files] returns ok ++[expiration] returns noop ++[logintime] returns noop ++[pap] returns noop Found Auth-Type = EAP +- entering group authenticate {...} [eap] EAP Identity [eap] processing type mschapv2 rlm_eap_mschapv2: Issuing Challenge ++[eap] returns handled } # server inner-tunnel [peap] Got tunneled reply code 11 Auth-Type := Accept Reply-Message = "You have been authenticated" EAP-Message = 0x010800211a0108001c104c7d6d16e4d3682db039701272ef79586d617269737361 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x27b4133127bc09524480fddc531df9e5 [peap] Got tunneled reply RADIUS code 11 Auth-Type := Accept Reply-Message = "You have been authenticated" EAP-Message = 0x010800211a0108001c104c7d6d16e4d3682db039701272ef79586d617269737361 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x27b4133127bc09524480fddc531df9e5 [peap] Got tunneled Access-Challenge ++[eap] returns handled Sending Access-Challenge of id 90 to 192.168.1.1 port 44783 EAP-Message = 0x0108004b19001703010040427a79bc52032f8dd9260e9b8fae5b50244fcf98c6d97c541103fd3249fb44c1cd8abec69572b2df56644dcba630c48d050b553de594c04b9aa47148186a2115 Message-Authenticator = 0x00000000000000000000000000000000 State = 0xd9001cbcdf08052adaeb377365c8c185 Finished request 6. Going to the next request Waking up in 4.8 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=91, length=275 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x0208006b19001703010060d05f0b2f7e1f68309679d43d8cf9d1ceaed585bc13d0f63327ce85dac120ae511c1262a39b1fb943d74aecae5bd9d9e142c2aa07d7f797097d69ff84594adedff500bdfdf178fbf63ba0e36aa9b9ed184f62a489f942c9f4a4ac7a9f572c591b State = 0xd9001cbcdf08052adaeb377365c8c185 Message-Authenticator = 0x8cc456db98d3e8de5e271ac3582ceec3 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 8 length 107 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] eaptls_verify returned 7 [peap] Done initial handshake [peap] eaptls_process returned 7 [peap] EAPTLS_OK [peap] Session established. Decoding tunneled attributes. [peap] EAP type mschapv2 [peap] Got tunnled request EAP-Message = 0x020800421a0208003d31bdd42b430d7fae3f0e51831ffaa272510000000000000000f62747d73832a3ebd653e6f008a1b58c0c6b0c64ceb8c78a006d617269737361 server (null) { PEAP: Setting User-Name to marissa Sending tunneled request EAP-Message = 0x020800421a0208003d31bdd42b430d7fae3f0e51831ffaa272510000000000000000f62747d73832a3ebd653e6f008a1b58c0c6b0c64ceb8c78a006d617269737361 FreeRADIUS-Proxied-To = 127.0.0.1 User-Name = "marissa" State = 0x27b4133127bc09524480fddc531df9e5 server inner-tunnel { +- entering group authorize {...} ++[chap] returns noop ++[mschap] returns noop ++[unix] returns notfound [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop ++[control] returns noop [eap] EAP packet type response id 8 length 66 [eap] No EAP Start, assuming it's an on-going EAP conversation ++[eap] returns updated rlm_ldap: Entering ldap_groupcmp() [files] expand: ou=ou,o=org -> ou=ou,o=org [files] WARNING: Deprecated conditional expansion ":-". See "man unlang" for details [files] expand: (uid=%{Stripped-User-Name:-%{User-Name}}) -> (uid=marissa) rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=ou,o=org, with filter (uid=marissa) rlm_ldap: ldap_release_conn: Release Id: 0 [files] expand: (|(&(objectClass=GroupOfNames)(member=%{check:Ldap-UserDn}))(&(objectClass=GroupOfUniqueNames)(uniquemember=%{Ldap-UserDn}))) -> (|(&(objectClass=GroupOfNames)(member=cn\3dMarissa\2cou\3dou\2co\3dorg))(&(objectClass=GroupOfUniqueNames)(uniquemember=))) rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in cn=Corporate Wireless Network,ou=ou,o=org, with filter (|(&(objectClass=GroupOfNames)(member=cn\3dMarissa\2cou\3dou\2co\3dorg))(&(objectClass=GroupOfUniqueNames)(uniquemember=))) rlm_ldap::ldap_groupcmp: User found in group cn=Corporate Wireless Network,ou=ou,o=org rlm_ldap: ldap_release_conn: Release Id: 0 [files] users: Matched entry DEFAULT at line 3 ++[files] returns ok ++[expiration] returns noop ++[logintime] returns noop ++[pap] returns noop Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/mschapv2 [eap] processing type mschapv2 [mschapv2] +- entering group MS-CHAP {...} [mschap] No Cleartext-Password configured. Cannot create LM-Password. [mschap] No Cleartext-Password configured. Cannot create NT-Password. [mschap] Told to do MS-CHAPv2 for marissa with NT-Password [mschap] FAILED: No NT/LM-Password. Cannot perform authentication. [mschap] FAILED: MS-CHAP2-Response is incorrect ++[mschap] returns reject [eap] Freeing handler ++[eap] returns reject Failed to authenticate the user. } # server inner-tunnel [peap] Got tunneled reply code 3 Auth-Type := Accept Reply-Message = "You have been authenticated" MS-CHAP-Error = "\010E=691 R=1" EAP-Message = 0x04080004 Message-Authenticator = 0x00000000000000000000000000000000 [peap] Got tunneled reply RADIUS code 3 Auth-Type := Accept Reply-Message = "You have been authenticated" MS-CHAP-Error = "\010E=691 R=1" EAP-Message = 0x04080004 Message-Authenticator = 0x00000000000000000000000000000000 [peap] Tunneled authentication was rejected. [peap] FAILURE ++[eap] returns handled Sending Access-Challenge of id 91 to 192.168.1.1 port 44783 EAP-Message = 0x0109002b190017030100202666e0fc4864bb1b4246ae2666c3c8a332996c8be347fc9e75497ad0ac439649 Message-Authenticator = 0x00000000000000000000000000000000 State = 0xd9001cbcde09052adaeb377365c8c185 Finished request 7. Going to the next request Waking up in 4.8 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=92, length=211 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x0209002b19001703010020c1e2322db45a1fb3a71d66f3753f631f70928867ac73dd0e81236fb5a29d98cd State = 0xd9001cbcde09052adaeb377365c8c185 Message-Authenticator = 0xac4310fef08997338b69f8b5899758ec +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 9 length 43 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] eaptls_verify returned 7 [peap] Done initial handshake [peap] eaptls_process returned 7 [peap] EAPTLS_OK [peap] Session established. Decoding tunneled attributes. [peap] Received EAP-TLV response. [peap] Had sent TLV failure. User was rejected earlier in this session. [eap] Handler failed in EAP/peap [eap] Failed in EAP select ++[eap] returns invalid Failed to authenticate the user. Using Post-Auth-Type Reject +- entering group REJECT {...} ++[ldap] returns noop Delaying reject of request 8 for 1 seconds Going to the next request Waking up in 0.9 seconds. Sending delayed reject for request 8 Sending Access-Reject of id 92 to 192.168.1.1 port 44783 EAP-Message = 0x04090004 Message-Authenticator = 0x00000000000000000000000000000000 Waking up in 3.8 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=93, length=162 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x02d4000c016d617269737361 Message-Authenticator = 0x5f3439e62d108fe4ec3453c944345f1d +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 212 length 12 [eap] No EAP Start, assuming it's an on-going EAP conversation ++[eap] returns updated ++[unix] returns notfound rlm_ldap: Entering ldap_groupcmp() [files] expand: ou=ou,o=org -> ou=ou,o=org [files] WARNING: Deprecated conditional expansion ":-". See "man unlang" for details [files] expand: (uid=%{Stripped-User-Name:-%{User-Name}}) -> (uid=marissa) rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=ou,o=org, with filter (uid=marissa) rlm_ldap: ldap_release_conn: Release Id: 0 [files] expand: (|(&(objectClass=GroupOfNames)(member=%{check:Ldap-UserDn}))(&(objectClass=GroupOfUniqueNames)(uniquemember=%{Ldap-UserDn}))) -> (|(&(objectClass=GroupOfNames)(member=cn\3dMarissa\2cou\3dou\2co\3dorg))(&(objectClass=GroupOfUniqueNames)(uniquemember=))) rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in cn=Corporate Wireless Network,ou=ou,o=org, with filter (|(&(objectClass=GroupOfNames)(member=cn\3dMarissa\2cou\3dou\2co\3dorg))(&(objectClass=GroupOfUniqueNames)(uniquemember=))) rlm_ldap::ldap_groupcmp: User found in group cn=Corporate Wireless Network,ou=ou,o=org rlm_ldap: ldap_release_conn: Release Id: 0 [files] users: Matched entry DEFAULT at line 3 ++[files] returns ok [ldap] performing user authorization for marissa [ldap] WARNING: Deprecated conditional expansion ":-". See "man unlang" for details [ldap] expand: (uid=%{Stripped-User-Name:-%{User-Name}}) -> (uid=marissa) [ldap] expand: ou=ou,o=org -> ou=ou,o=org rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=ou,o=org, with filter (uid=marissa) [ldap] No default NMAS login sequence [ldap] looking for check items in directory... [ldap] looking for reply items in directory... WARNING: No "known good" password was found in LDAP. Are you sure that the user is configured correctly? [ldap] user marissa authorized to use remote access rlm_ldap: ldap_release_conn: Release Id: 0 ++[ldap] returns ok ++[expiration] returns noop ++[logintime] returns noop [pap] WARNING! No "known good" password found for the user. Authentication may fail because of this. ++[pap] returns noop Found Auth-Type = EAP +- entering group authenticate {...} [eap] EAP Identity [eap] processing type tls [tls] Initiate [tls] Start returned 1 ++[eap] returns handled Sending Access-Challenge of id 93 to 192.168.1.1 port 44783 Reply-Message = "You have been authenticated" EAP-Message = 0x01d500061920 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x4c79eeeb4cacf7adde98b3784d2ef1bf Finished request 9. Going to the next request Waking up in 3.2 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=94, length=320 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x02d5009819800000008e16030100890100008503015525d4b816975f51351d97cfa37244f07191e59fa5ed1467144801e94b0f1d1c00004a00ffc024c023c00ac009c007c008c028c027c014c013c011c012c026c025c02ac029c005c004c002c003c00fc00ec00cc00d003d003c002f000500040035000a0067006b00330039001601000012000a00080006001700180019000b00020100 State = 0x4c79eeeb4cacf7adde98b3784d2ef1bf Message-Authenticator = 0x23f7a8e56a5b168597d8521d99cff1ba +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 213 length 152 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS TLS Length 142 [peap] Length Included [peap] eaptls_verify returned 11 [peap] (other): before/accept initialization [peap] TLS_accept: before/accept initialization [peap] <<< TLS 1.0 Handshake [length 0089], ClientHello [peap] TLS_accept: SSLv3 read client hello A [peap] >>> TLS 1.0 Handshake [length 0031], ServerHello [peap] TLS_accept: SSLv3 write server hello A [peap] >>> TLS 1.0 Handshake [length 08e7], Certificate [peap] TLS_accept: SSLv3 write certificate A [peap] >>> TLS 1.0 Handshake [length 0004], ServerHelloDone [peap] TLS_accept: SSLv3 write server done A [peap] TLS_accept: SSLv3 flush data [peap] TLS_accept: Need to read more data: SSLv3 read client certificate A In SSL Handshake Phase In SSL Accept mode [peap] eaptls_process returned 13 [peap] EAPTLS_HANDLED ++[eap] returns handled Sending Access-Challenge of id 94 to 192.168.1.1 port 44783 EAP-Message = 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 EAP-Message = 0x39322e3136382e312e31343125302306092a864886f70d0109011616627269616e2e626f657265406e657477697a652e636130820122300d06092a864886f70d01010105000382010f003082010a0282010100b45fca756783b50bbfe192db5605f61d380516c1de497e826fd3a2daf955704b178bc3a460e3ccfce49bccbcea14311dbfd09ca5a4e23ebbde8c403dc4fe319f67e230e18c76e1c654ded7117dc92982af9b130aa16e142c57b79c90b42033cd74fbe9b8441600f3498e5b27806a4c28eb73b2581dc971114144aaa902d317f4ac15686aa5437b0e339eee9421c20179fcc4fa33bf8774ffb5db47c820b891e9625c2592f2be9e71feb5 EAP-Message = 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 EAP-Message = 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 EAP-Message = 0xc58044f3ddec6c0e7f82e084 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x4c79eeeb4daff7adde98b3784d2ef1bf Finished request 10. Going to the next request Waking up in 3.1 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=95, length=174 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x02d600061900 State = 0x4c79eeeb4daff7adde98b3784d2ef1bf Message-Authenticator = 0xdf1a34fc2b331ab8223f0914e5a375d9 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 214 length 6 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] Received TLS ACK [peap] ACK handshake fragment handler [peap] eaptls_verify returned 1 [peap] eaptls_process returned 13 [peap] EAPTLS_HANDLED ++[eap] returns handled Sending Access-Challenge of id 95 to 192.168.1.1 port 44783 EAP-Message = 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 EAP-Message = 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 EAP-Message = 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 EAP-Message = 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 EAP-Message = 0x7240626f6572652e Message-Authenticator = 0x00000000000000000000000000000000 State = 0x4c79eeeb4eaef7adde98b3784d2ef1bf Finished request 11. Going to the next request Waking up in 3.1 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=96, length=174 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x02d700061900 State = 0x4c79eeeb4eaef7adde98b3784d2ef1bf Message-Authenticator = 0x9a063525d73ce28faa24e08ebe285454 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 215 length 6 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] Received TLS ACK [peap] ACK handshake fragment handler [peap] eaptls_verify returned 1 [peap] eaptls_process returned 13 [peap] EAPTLS_HANDLED ++[eap] returns handled Sending Access-Challenge of id 96 to 192.168.1.1 port 44783 EAP-Message = 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 EAP-Message = 0xb0c10bdf7d58306a9b62f457869be27e0500f12bb5bdbf451afcd037f43bd26db19169f9fd88a6ab8f49783d3718a97908838502011a8b6cfea38002e6929816030100040e000000 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x4c79eeeb4fa1f7adde98b3784d2ef1bf Finished request 12. Going to the next request Waking up in 3.0 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=97, length=506 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 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 EAP-Message = 0xef0c4af27d967df6c3f56b6f5f475f30e7cff3eac9bed619140301000101160301003086a05537342a365768b7f6212c3ce5ae62ce6e98479b102d725020f94a3642a5165ac932c6db50f6af86ea4da31b42c2 State = 0x4c79eeeb4fa1f7adde98b3784d2ef1bf Message-Authenticator = 0xf9074324e9c31069cf37be2a2c38922d +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 216 length 253 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS TLS Length 326 [peap] Length Included [peap] eaptls_verify returned 11 [peap] <<< TLS 1.0 Handshake [length 0106], ClientKeyExchange [peap] TLS_accept: SSLv3 read client key exchange A [peap] <<< TLS 1.0 ChangeCipherSpec [length 0001] [peap] <<< TLS 1.0 Handshake [length 0010], Finished [peap] TLS_accept: SSLv3 read finished A [peap] >>> TLS 1.0 ChangeCipherSpec [length 0001] [peap] TLS_accept: SSLv3 write change cipher spec A [peap] >>> TLS 1.0 Handshake [length 0010], Finished [peap] TLS_accept: SSLv3 write finished A [peap] TLS_accept: SSLv3 flush data [peap] (other): SSL negotiation finished successfully SSL Connection Established [peap] eaptls_process returned 13 [peap] EAPTLS_HANDLED ++[eap] returns handled Sending Access-Challenge of id 97 to 192.168.1.1 port 44783 EAP-Message = 0x01d9004119001403010001011603010030ec4119debae3083cdaccc8610558ce4a65aeced17553eee9c1ad079e3218daf575314615ea75d1dbb7b837aae7869dc3 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x4c79eeeb48a0f7adde98b3784d2ef1bf Finished request 13. Going to the next request Waking up in 3.0 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=98, length=174 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x02d900061900 State = 0x4c79eeeb48a0f7adde98b3784d2ef1bf Message-Authenticator = 0x5ff41ba10c61525f1d5cffba92e0c93f +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 217 length 6 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] Received TLS ACK [peap] ACK handshake is finished [peap] eaptls_verify returned 3 [peap] eaptls_process returned 3 [peap] EAPTLS_SUCCESS ++[eap] returns handled Sending Access-Challenge of id 98 to 192.168.1.1 port 44783 EAP-Message = 0x01da002b19001703010020dd5077e04204e1677d2f4683939405977f9cd8bc67ef336b4f8a4cbdf987b309 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x4c79eeeb49a3f7adde98b3784d2ef1bf Finished request 14. Going to the next request Waking up in 3.0 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=99, length=211 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x02da002b19001703010020b89f05c9c405c9e43821efc0ff9e872313ecb72139c46527981f9052aea96d0b State = 0x4c79eeeb49a3f7adde98b3784d2ef1bf Message-Authenticator = 0x090dd6c63c6d91d836dd845721cc7dd8 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 218 length 43 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] eaptls_verify returned 7 [peap] Done initial handshake [peap] eaptls_process returned 7 [peap] EAPTLS_OK [peap] Session established. Decoding tunneled attributes. [peap] Identity - marissa [peap] Got tunnled request EAP-Message = 0x02da000c016d617269737361 server (null) { PEAP: Got tunneled identity of marissa PEAP: Setting default EAP type for tunneled EAP session. PEAP: Setting User-Name to marissa Sending tunneled request EAP-Message = 0x02da000c016d617269737361 FreeRADIUS-Proxied-To = 127.0.0.1 User-Name = "marissa" server inner-tunnel { +- entering group authorize {...} ++[chap] returns noop ++[mschap] returns noop ++[unix] returns notfound [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop ++[control] returns noop [eap] EAP packet type response id 218 length 12 [eap] No EAP Start, assuming it's an on-going EAP conversation ++[eap] returns updated rlm_ldap: Entering ldap_groupcmp() [files] expand: ou=ou,o=org -> ou=ou,o=org [files] WARNING: Deprecated conditional expansion ":-". See "man unlang" for details [files] expand: (uid=%{Stripped-User-Name:-%{User-Name}}) -> (uid=marissa) rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=ou,o=org, with filter (uid=marissa) rlm_ldap: ldap_release_conn: Release Id: 0 [files] expand: (|(&(objectClass=GroupOfNames)(member=%{check:Ldap-UserDn}))(&(objectClass=GroupOfUniqueNames)(uniquemember=%{Ldap-UserDn}))) -> (|(&(objectClass=GroupOfNames)(member=cn\3dMarissa\2cou\3dou\2co\3dorg))(&(objectClass=GroupOfUniqueNames)(uniquemember=))) rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in cn=Corporate Wireless Network,ou=ou,o=org, with filter (|(&(objectClass=GroupOfNames)(member=cn\3dMarissa\2cou\3dou\2co\3dorg))(&(objectClass=GroupOfUniqueNames)(uniquemember=))) rlm_ldap::ldap_groupcmp: User found in group cn=Corporate Wireless Network,ou=ou,o=org rlm_ldap: ldap_release_conn: Release Id: 0 [files] users: Matched entry DEFAULT at line 3 ++[files] returns ok ++[expiration] returns noop ++[logintime] returns noop ++[pap] returns noop Found Auth-Type = EAP +- entering group authenticate {...} [eap] EAP Identity [eap] processing type mschapv2 rlm_eap_mschapv2: Issuing Challenge ++[eap] returns handled } # server inner-tunnel [peap] Got tunneled reply code 11 Auth-Type := Accept Reply-Message = "You have been authenticated" EAP-Message = 0x01db00211a01db001c1006f44211bbf1dba43133529c64c2fa9b6d617269737361 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x8a77cf098aacd550855fedefe5b907b1 [peap] Got tunneled reply RADIUS code 11 Auth-Type := Accept Reply-Message = "You have been authenticated" EAP-Message = 0x01db00211a01db001c1006f44211bbf1dba43133529c64c2fa9b6d617269737361 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x8a77cf098aacd550855fedefe5b907b1 [peap] Got tunneled Access-Challenge ++[eap] returns handled Sending Access-Challenge of id 99 to 192.168.1.1 port 44783 EAP-Message = 0x01db004b1900170301004003353bd1e64ee9f527af5b929a2808f15b2dbcc80600b775c63995e0e3ae800f7d1a1a9f15c17f84d2fc249acfc870e313e8d3f46d4ee423e84d4cc6fd07372d Message-Authenticator = 0x00000000000000000000000000000000 State = 0x4c79eeeb4aa2f7adde98b3784d2ef1bf Finished request 15. Going to the next request Waking up in 3.0 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=100, length=275 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x02db006b19001703010060ffa9aac740c65dc12e7a959f296bf340e055a4603f4cbcbde091a2d0820529a0ce5244adcd5122e0ccbbbde47834139aa91365b6105dc989444ca730cd264c9e2366d317f205c5d4bcfcbd7827f73c9ee0f9bb220f69f470f63bfb7c17f42b5d State = 0x4c79eeeb4aa2f7adde98b3784d2ef1bf Message-Authenticator = 0x39b6d35b79cb30bbd8ce5cd98c68bdea +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 219 length 107 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] eaptls_verify returned 7 [peap] Done initial handshake [peap] eaptls_process returned 7 [peap] EAPTLS_OK [peap] Session established. Decoding tunneled attributes. [peap] EAP type mschapv2 [peap] Got tunnled request EAP-Message = 0x02db00421a02db003d31098aaae470987c845a9a81acf3bfa4a9000000000000000060997998dc92fde1a889706b2df5c8aea37a97d63644286f006d617269737361 server (null) { PEAP: Setting User-Name to marissa Sending tunneled request EAP-Message = 0x02db00421a02db003d31098aaae470987c845a9a81acf3bfa4a9000000000000000060997998dc92fde1a889706b2df5c8aea37a97d63644286f006d617269737361 FreeRADIUS-Proxied-To = 127.0.0.1 User-Name = "marissa" State = 0x8a77cf098aacd550855fedefe5b907b1 server inner-tunnel { +- entering group authorize {...} ++[chap] returns noop ++[mschap] returns noop ++[unix] returns notfound [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop ++[control] returns noop [eap] EAP packet type response id 219 length 66 [eap] No EAP Start, assuming it's an on-going EAP conversation ++[eap] returns updated rlm_ldap: Entering ldap_groupcmp() [files] expand: ou=ou,o=org -> ou=ou,o=org [files] WARNING: Deprecated conditional expansion ":-". See "man unlang" for details [files] expand: (uid=%{Stripped-User-Name:-%{User-Name}}) -> (uid=marissa) rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=ou,o=org, with filter (uid=marissa) rlm_ldap: ldap_release_conn: Release Id: 0 [files] expand: (|(&(objectClass=GroupOfNames)(member=%{check:Ldap-UserDn}))(&(objectClass=GroupOfUniqueNames)(uniquemember=%{Ldap-UserDn}))) -> (|(&(objectClass=GroupOfNames)(member=cn\3dMarissa\2cou\3dou\2co\3dorg))(&(objectClass=GroupOfUniqueNames)(uniquemember=))) rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in cn=Corporate Wireless Network,ou=ou,o=org, with filter (|(&(objectClass=GroupOfNames)(member=cn\3dMarissa\2cou\3dou\2co\3dorg))(&(objectClass=GroupOfUniqueNames)(uniquemember=))) rlm_ldap::ldap_groupcmp: User found in group cn=Corporate Wireless Network,ou=ou,o=org rlm_ldap: ldap_release_conn: Release Id: 0 [files] users: Matched entry DEFAULT at line 3 ++[files] returns ok ++[expiration] returns noop ++[logintime] returns noop ++[pap] returns noop Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/mschapv2 [eap] processing type mschapv2 [mschapv2] +- entering group MS-CHAP {...} [mschap] No Cleartext-Password configured. Cannot create LM-Password. [mschap] No Cleartext-Password configured. Cannot create NT-Password. [mschap] Told to do MS-CHAPv2 for marissa with NT-Password [mschap] FAILED: No NT/LM-Password. Cannot perform authentication. [mschap] FAILED: MS-CHAP2-Response is incorrect ++[mschap] returns reject [eap] Freeing handler ++[eap] returns reject Failed to authenticate the user. } # server inner-tunnel [peap] Got tunneled reply code 3 Auth-Type := Accept Reply-Message = "You have been authenticated" MS-CHAP-Error = "\333E=691 R=1" EAP-Message = 0x04db0004 Message-Authenticator = 0x00000000000000000000000000000000 [peap] Got tunneled reply RADIUS code 3 Auth-Type := Accept Reply-Message = "You have been authenticated" MS-CHAP-Error = "\333E=691 R=1" EAP-Message = 0x04db0004 Message-Authenticator = 0x00000000000000000000000000000000 [peap] Tunneled authentication was rejected. [peap] FAILURE ++[eap] returns handled Sending Access-Challenge of id 100 to 192.168.1.1 port 44783 EAP-Message = 0x01dc002b19001703010020234c8b70f2d7586fee9428c53f96cee4363089b244c5ee64c6d723b5a2dd5ecf Message-Authenticator = 0x00000000000000000000000000000000 State = 0x4c79eeeb4ba5f7adde98b3784d2ef1bf Finished request 16. Going to the next request Waking up in 3.0 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=101, length=211 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x02dc002b190017030100202f8b97f87bcb382c1712e9e0890ad643a45a137be8301c0625a0d28ceaabe601 State = 0x4c79eeeb4ba5f7adde98b3784d2ef1bf Message-Authenticator = 0xfa1f12d313eb1b4de35053eacef7da9c +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 220 length 43 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] eaptls_verify returned 7 [peap] Done initial handshake [peap] eaptls_process returned 7 [peap] EAPTLS_OK [peap] Session established. Decoding tunneled attributes. [peap] Received EAP-TLV response. [peap] Had sent TLV failure. User was rejected earlier in this session. [eap] Handler failed in EAP/peap [eap] Failed in EAP select ++[eap] returns invalid Failed to authenticate the user. Using Post-Auth-Type Reject +- entering group REJECT {...} ++[ldap] returns noop Delaying reject of request 17 for 1 seconds Going to the next request Waking up in 0.9 seconds. Sending delayed reject for request 17 Sending Access-Reject of id 101 to 192.168.1.1 port 44783 EAP-Message = 0x04dc0004 Message-Authenticator = 0x00000000000000000000000000000000 Waking up in 1.9 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=102, length=162 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x02ca000c016d617269737361 Message-Authenticator = 0x17a397da00b824abf91a03c74dd89038 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 202 length 12 [eap] No EAP Start, assuming it's an on-going EAP conversation ++[eap] returns updated ++[unix] returns notfound rlm_ldap: Entering ldap_groupcmp() [files] expand: ou=ou,o=org -> ou=ou,o=org [files] WARNING: Deprecated conditional expansion ":-". See "man unlang" for details [files] expand: (uid=%{Stripped-User-Name:-%{User-Name}}) -> (uid=marissa) rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=ou,o=org, with filter (uid=marissa) rlm_ldap: ldap_release_conn: Release Id: 0 [files] expand: (|(&(objectClass=GroupOfNames)(member=%{check:Ldap-UserDn}))(&(objectClass=GroupOfUniqueNames)(uniquemember=%{Ldap-UserDn}))) -> (|(&(objectClass=GroupOfNames)(member=cn\3dMarissa\2cou\3dou\2co\3dorg))(&(objectClass=GroupOfUniqueNames)(uniquemember=))) rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in cn=Corporate Wireless Network,ou=ou,o=org, with filter (|(&(objectClass=GroupOfNames)(member=cn\3dMarissa\2cou\3dou\2co\3dorg))(&(objectClass=GroupOfUniqueNames)(uniquemember=))) rlm_ldap::ldap_groupcmp: User found in group cn=Corporate Wireless Network,ou=ou,o=org rlm_ldap: ldap_release_conn: Release Id: 0 [files] users: Matched entry DEFAULT at line 3 ++[files] returns ok [ldap] performing user authorization for marissa [ldap] WARNING: Deprecated conditional expansion ":-". See "man unlang" for details [ldap] expand: (uid=%{Stripped-User-Name:-%{User-Name}}) -> (uid=marissa) [ldap] expand: ou=ou,o=org -> ou=ou,o=org rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=ou,o=org, with filter (uid=marissa) [ldap] No default NMAS login sequence [ldap] looking for check items in directory... [ldap] looking for reply items in directory... WARNING: No "known good" password was found in LDAP. Are you sure that the user is configured correctly? [ldap] user marissa authorized to use remote access rlm_ldap: ldap_release_conn: Release Id: 0 ++[ldap] returns ok ++[expiration] returns noop ++[logintime] returns noop [pap] WARNING! No "known good" password found for the user. Authentication may fail because of this. ++[pap] returns noop Found Auth-Type = EAP +- entering group authenticate {...} [eap] EAP Identity [eap] processing type tls [tls] Initiate [tls] Start returned 1 ++[eap] returns handled Sending Access-Challenge of id 102 to 192.168.1.1 port 44783 Reply-Message = "You have been authenticated" EAP-Message = 0x01cb00061920 Message-Authenticator = 0x00000000000000000000000000000000 State = 0xce01e300cecafa33f34fb10b4809c83e Finished request 18. Going to the next request Waking up in 1.3 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=103, length=320 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x02cb009819800000008e16030100890100008503015525d4bac1cbb767303f654b33b6628f5e1d6f9da3feec6901403f8ac797492200004a00ffc024c023c00ac009c007c008c028c027c014c013c011c012c026c025c02ac029c005c004c002c003c00fc00ec00cc00d003d003c002f000500040035000a0067006b00330039001601000012000a00080006001700180019000b00020100 State = 0xce01e300cecafa33f34fb10b4809c83e Message-Authenticator = 0x83d4a6de2f42960ab429de7f4d5f37f0 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 203 length 152 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS TLS Length 142 [peap] Length Included [peap] eaptls_verify returned 11 [peap] (other): before/accept initialization [peap] TLS_accept: before/accept initialization [peap] <<< TLS 1.0 Handshake [length 0089], ClientHello [peap] TLS_accept: SSLv3 read client hello A [peap] >>> TLS 1.0 Handshake [length 0031], ServerHello [peap] TLS_accept: SSLv3 write server hello A [peap] >>> TLS 1.0 Handshake [length 08e7], Certificate [peap] TLS_accept: SSLv3 write certificate A [peap] >>> TLS 1.0 Handshake [length 0004], ServerHelloDone [peap] TLS_accept: SSLv3 write server done A [peap] TLS_accept: SSLv3 flush data [peap] TLS_accept: Need to read more data: SSLv3 read client certificate A In SSL Handshake Phase In SSL Accept mode [peap] eaptls_process returned 13 [peap] EAPTLS_HANDLED ++[eap] returns handled Sending Access-Challenge of id 103 to 192.168.1.1 port 44783 EAP-Message = 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 EAP-Message = 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 EAP-Message = 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 EAP-Message = 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 EAP-Message = 0xc58044f3ddec6c0e7f82e084 Message-Authenticator = 0x00000000000000000000000000000000 State = 0xce01e300cfcdfa33f34fb10b4809c83e Finished request 19. Going to the next request Waking up in 1.2 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=104, length=174 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x02cc00061900 State = 0xce01e300cfcdfa33f34fb10b4809c83e Message-Authenticator = 0x0b3eb60b88e4d1d362aec3f7a641de5b +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 204 length 6 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] Received TLS ACK [peap] ACK handshake fragment handler [peap] eaptls_verify returned 1 [peap] eaptls_process returned 13 [peap] EAPTLS_HANDLED ++[eap] returns handled Sending Access-Challenge of id 104 to 192.168.1.1 port 44783 EAP-Message = 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 EAP-Message = 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 EAP-Message = 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 EAP-Message = 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 EAP-Message = 0x7240626f6572652e Message-Authenticator = 0x00000000000000000000000000000000 State = 0xce01e300ccccfa33f34fb10b4809c83e Finished request 20. Going to the next request Waking up in 1.2 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=105, length=174 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x02cd00061900 State = 0xce01e300ccccfa33f34fb10b4809c83e Message-Authenticator = 0xa43397ec7d12fe2a77126ad2442ed7e6 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 205 length 6 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] Received TLS ACK [peap] ACK handshake fragment handler [peap] eaptls_verify returned 1 [peap] eaptls_process returned 13 [peap] EAPTLS_HANDLED ++[eap] returns handled Sending Access-Challenge of id 105 to 192.168.1.1 port 44783 EAP-Message = 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 EAP-Message = 0xb0c10bdf7d58306a9b62f457869be27e0500f12bb5bdbf451afcd037f43bd26db19169f9fd88a6ab8f49783d3718a97908838502011a8b6cfea38002e6929816030100040e000000 Message-Authenticator = 0x00000000000000000000000000000000 State = 0xce01e300cdcffa33f34fb10b4809c83e Finished request 21. Going to the next request Waking up in 1.2 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=106, length=506 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 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 EAP-Message = 0x62bd37a94346cb02cf58db7ea00775cf22ac9c331dd4c5ee14030100010116030100305eadf915572979dcefd54005f2ea04446726c3694c1a6be20388a55f136d672c0c1ff3968d428a054c0d3aa6e069c437 State = 0xce01e300cdcffa33f34fb10b4809c83e Message-Authenticator = 0xc07f3a03ca86b7c21c832cde6ca90e8d +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 206 length 253 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS TLS Length 326 [peap] Length Included [peap] eaptls_verify returned 11 [peap] <<< TLS 1.0 Handshake [length 0106], ClientKeyExchange [peap] TLS_accept: SSLv3 read client key exchange A [peap] <<< TLS 1.0 ChangeCipherSpec [length 0001] [peap] <<< TLS 1.0 Handshake [length 0010], Finished [peap] TLS_accept: SSLv3 read finished A [peap] >>> TLS 1.0 ChangeCipherSpec [length 0001] [peap] TLS_accept: SSLv3 write change cipher spec A [peap] >>> TLS 1.0 Handshake [length 0010], Finished [peap] TLS_accept: SSLv3 write finished A [peap] TLS_accept: SSLv3 flush data [peap] (other): SSL negotiation finished successfully SSL Connection Established [peap] eaptls_process returned 13 [peap] EAPTLS_HANDLED ++[eap] returns handled Sending Access-Challenge of id 106 to 192.168.1.1 port 44783 EAP-Message = 0x01cf0041190014030100010116030100304829c62351e52bd5b670e2e03a108171f2c5bdc558cad7a56725a29123a7a78d42b88dbfe07cdabd7d35c55877119632 Message-Authenticator = 0x00000000000000000000000000000000 State = 0xce01e300cacefa33f34fb10b4809c83e Finished request 22. Going to the next request Waking up in 1.1 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=107, length=174 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x02cf00061900 State = 0xce01e300cacefa33f34fb10b4809c83e Message-Authenticator = 0x5fb219c59a70c0761ef3a113ad774769 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 207 length 6 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] Received TLS ACK [peap] ACK handshake is finished [peap] eaptls_verify returned 3 [peap] eaptls_process returned 3 [peap] EAPTLS_SUCCESS ++[eap] returns handled Sending Access-Challenge of id 107 to 192.168.1.1 port 44783 EAP-Message = 0x01d0002b190017030100205acfab8e6c9de1d4cf1483baa3a17ae2b91fc3fd594b975d8652c887f20e2781 Message-Authenticator = 0x00000000000000000000000000000000 State = 0xce01e300cbd1fa33f34fb10b4809c83e Finished request 23. Going to the next request Waking up in 1.1 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=108, length=211 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x02d0002b19001703010020fd32a4e904d2d88881091407ce432248a586e6ead8e8560d9ce6fb4b97c772b8 State = 0xce01e300cbd1fa33f34fb10b4809c83e Message-Authenticator = 0xa1a3ed181082aa170dad26734174fab8 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 208 length 43 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] eaptls_verify returned 7 [peap] Done initial handshake [peap] eaptls_process returned 7 [peap] EAPTLS_OK [peap] Session established. Decoding tunneled attributes. [peap] Identity - marissa [peap] Got tunnled request EAP-Message = 0x02d0000c016d617269737361 server (null) { PEAP: Got tunneled identity of marissa PEAP: Setting default EAP type for tunneled EAP session. PEAP: Setting User-Name to marissa Sending tunneled request EAP-Message = 0x02d0000c016d617269737361 FreeRADIUS-Proxied-To = 127.0.0.1 User-Name = "marissa" server inner-tunnel { +- entering group authorize {...} ++[chap] returns noop ++[mschap] returns noop ++[unix] returns notfound [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop ++[control] returns noop [eap] EAP packet type response id 208 length 12 [eap] No EAP Start, assuming it's an on-going EAP conversation ++[eap] returns updated rlm_ldap: Entering ldap_groupcmp() [files] expand: ou=ou,o=org -> ou=ou,o=org [files] WARNING: Deprecated conditional expansion ":-". See "man unlang" for details [files] expand: (uid=%{Stripped-User-Name:-%{User-Name}}) -> (uid=marissa) rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=ou,o=org, with filter (uid=marissa) rlm_ldap: ldap_release_conn: Release Id: 0 [files] expand: (|(&(objectClass=GroupOfNames)(member=%{check:Ldap-UserDn}))(&(objectClass=GroupOfUniqueNames)(uniquemember=%{Ldap-UserDn}))) -> (|(&(objectClass=GroupOfNames)(member=cn\3dMarissa\2cou\3dou\2co\3dorg))(&(objectClass=GroupOfUniqueNames)(uniquemember=))) rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in cn=Corporate Wireless Network,ou=ou,o=org, with filter (|(&(objectClass=GroupOfNames)(member=cn\3dMarissa\2cou\3dou\2co\3dorg))(&(objectClass=GroupOfUniqueNames)(uniquemember=))) rlm_ldap::ldap_groupcmp: User found in group cn=Corporate Wireless Network,ou=ou,o=org rlm_ldap: ldap_release_conn: Release Id: 0 [files] users: Matched entry DEFAULT at line 3 ++[files] returns ok ++[expiration] returns noop ++[logintime] returns noop ++[pap] returns noop Found Auth-Type = EAP +- entering group authenticate {...} [eap] EAP Identity [eap] processing type mschapv2 rlm_eap_mschapv2: Issuing Challenge ++[eap] returns handled } # server inner-tunnel [peap] Got tunneled reply code 11 Auth-Type := Accept Reply-Message = "You have been authenticated" EAP-Message = 0x01d100211a01d1001c1023c4e56ce6cc92f8aceaf35ee03427d86d617269737361 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x745bf08c748aeaf7fc586b32e6203876 [peap] Got tunneled reply RADIUS code 11 Auth-Type := Accept Reply-Message = "You have been authenticated" EAP-Message = 0x01d100211a01d1001c1023c4e56ce6cc92f8aceaf35ee03427d86d617269737361 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x745bf08c748aeaf7fc586b32e6203876 [peap] Got tunneled Access-Challenge ++[eap] returns handled Sending Access-Challenge of id 108 to 192.168.1.1 port 44783 EAP-Message = 0x01d1004b19001703010040cd91b35cfabec35d0462d201122bb2e93741775304b16d9a1d6dac65ec3a029c5be6f0b29dd0e86ca14c8c9aa741cd34b623044ca95c629aaab8816b1dbc5852 Message-Authenticator = 0x00000000000000000000000000000000 State = 0xce01e300c8d0fa33f34fb10b4809c83e Finished request 24. Going to the next request Waking up in 1.1 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=109, length=275 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x02d1006b190017030100609a897b8987754b09e81aca14dc9a9098640b9a05cbe31d4b99129bb7fb016b9a816db212d1d9800a1a525c01ab6ef3966e1b38f67ca89b1aa9f89412098a8616c6b3cb940148033cc11a17f48a55ebbca06bf3e7f26c33da48eb0279388697ed State = 0xce01e300c8d0fa33f34fb10b4809c83e Message-Authenticator = 0xc8f3bd2fdbda518d59ba9c1f7d7ccd67 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 209 length 107 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] eaptls_verify returned 7 [peap] Done initial handshake [peap] eaptls_process returned 7 [peap] EAPTLS_OK [peap] Session established. Decoding tunneled attributes. [peap] EAP type mschapv2 [peap] Got tunnled request EAP-Message = 0x02d100421a02d1003d3154c095501f5720d0dae982b518982a9a000000000000000085b48dcd56edca08a085b3fd1dfb05d6a544625d5db0ee00006d617269737361 server (null) { PEAP: Setting User-Name to marissa Sending tunneled request EAP-Message = 0x02d100421a02d1003d3154c095501f5720d0dae982b518982a9a000000000000000085b48dcd56edca08a085b3fd1dfb05d6a544625d5db0ee00006d617269737361 FreeRADIUS-Proxied-To = 127.0.0.1 User-Name = "marissa" State = 0x745bf08c748aeaf7fc586b32e6203876 server inner-tunnel { +- entering group authorize {...} ++[chap] returns noop ++[mschap] returns noop ++[unix] returns notfound [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop ++[control] returns noop [eap] EAP packet type response id 209 length 66 [eap] No EAP Start, assuming it's an on-going EAP conversation ++[eap] returns updated rlm_ldap: Entering ldap_groupcmp() [files] expand: ou=ou,o=org -> ou=ou,o=org [files] WARNING: Deprecated conditional expansion ":-". See "man unlang" for details [files] expand: (uid=%{Stripped-User-Name:-%{User-Name}}) -> (uid=marissa) rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in ou=ou,o=org, with filter (uid=marissa) rlm_ldap: ldap_release_conn: Release Id: 0 [files] expand: (|(&(objectClass=GroupOfNames)(member=%{check:Ldap-UserDn}))(&(objectClass=GroupOfUniqueNames)(uniquemember=%{Ldap-UserDn}))) -> (|(&(objectClass=GroupOfNames)(member=cn\3dMarissa\2cou\3dou\2co\3dorg))(&(objectClass=GroupOfUniqueNames)(uniquemember=))) rlm_ldap: ldap_get_conn: Checking Id: 0 rlm_ldap: ldap_get_conn: Got Id: 0 rlm_ldap: performing search in cn=Corporate Wireless Network,ou=ou,o=org, with filter (|(&(objectClass=GroupOfNames)(member=cn\3dMarissa\2cou\3dou\2co\3dorg))(&(objectClass=GroupOfUniqueNames)(uniquemember=))) rlm_ldap::ldap_groupcmp: User found in group cn=Corporate Wireless Network,ou=ou,o=org rlm_ldap: ldap_release_conn: Release Id: 0 [files] users: Matched entry DEFAULT at line 3 ++[files] returns ok ++[expiration] returns noop ++[logintime] returns noop ++[pap] returns noop Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/mschapv2 [eap] processing type mschapv2 [mschapv2] +- entering group MS-CHAP {...} [mschap] No Cleartext-Password configured. Cannot create LM-Password. [mschap] No Cleartext-Password configured. Cannot create NT-Password. [mschap] Told to do MS-CHAPv2 for marissa with NT-Password [mschap] FAILED: No NT/LM-Password. Cannot perform authentication. [mschap] FAILED: MS-CHAP2-Response is incorrect ++[mschap] returns reject [eap] Freeing handler ++[eap] returns reject Failed to authenticate the user. } # server inner-tunnel [peap] Got tunneled reply code 3 Auth-Type := Accept Reply-Message = "You have been authenticated" MS-CHAP-Error = "\321E=691 R=1" EAP-Message = 0x04d10004 Message-Authenticator = 0x00000000000000000000000000000000 [peap] Got tunneled reply RADIUS code 3 Auth-Type := Accept Reply-Message = "You have been authenticated" MS-CHAP-Error = "\321E=691 R=1" EAP-Message = 0x04d10004 Message-Authenticator = 0x00000000000000000000000000000000 [peap] Tunneled authentication was rejected. [peap] FAILURE ++[eap] returns handled Sending Access-Challenge of id 109 to 192.168.1.1 port 44783 EAP-Message = 0x01d2002b190017030100206c6a2815e2226ebc4ebadbe29ef167db65e402ebc8a15e98d10e97c210ae81d7 Message-Authenticator = 0x00000000000000000000000000000000 State = 0xce01e300c9d3fa33f34fb10b4809c83e Finished request 25. Going to the next request Waking up in 1.1 seconds. rad_recv: Access-Request packet from host 192.168.1.1 port 44783, id=110, length=211 User-Name = "marissa" NAS-Identifier = "Rad_test2" Called-Station-Id = "00-1A-8C-29-A2-C2:Rad_test2" NAS-Port-Type = Wireless-802.11 NAS-Port = 1 Calling-Station-Id = "E4-CE-8F-92-53-B8" Connect-Info = "CONNECT 54Mbps 802.11g" Framed-MTU = 1400 EAP-Message = 0x02d2002b19001703010020c9efb59fe5d4d3a00154aec0e02e65b128eaa9c11083a1fa3002834c82280894 State = 0xce01e300c9d3fa33f34fb10b4809c83e Message-Authenticator = 0xcbde3df03b9879f30cb1eec56354b553 +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop [suffix] No '@' in User-Name = "marissa", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] EAP packet type response id 210 length 43 [eap] Continuing tunnel setup. ++[eap] returns ok Found Auth-Type = EAP +- entering group authenticate {...} [eap] Request found, released from the list [eap] EAP/peap [eap] processing type peap [peap] processing EAP-TLS [peap] eaptls_verify returned 7 [peap] Done initial handshake [peap] eaptls_process returned 7 [peap] EAPTLS_OK [peap] Session established. Decoding tunneled attributes. [peap] Received EAP-TLV response. [peap] Had sent TLV failure. User was rejected earlier in this session. [eap] Handler failed in EAP/peap [eap] Failed in EAP select ++[eap] returns invalid Failed to authenticate the user. Using Post-Auth-Type Reject +- entering group REJECT {...} ++[ldap] returns noop Delaying reject of request 26 for 1 seconds Going to the next request Waking up in 0.9 seconds. Sending delayed reject for request 26 Sending Access-Reject of id 110 to 192.168.1.1 port 44783 EAP-Message = 0x04d20004 Message-Authenticator = 0x00000000000000000000000000000000 Waking up in 0.1 seconds. Cleaning up request 0 ID 84 with timestamp +11 Cleaning up request 1 ID 85 with timestamp +12 Cleaning up request 2 ID 86 with timestamp +12 Cleaning up request 3 ID 87 with timestamp +12 Cleaning up request 4 ID 88 with timestamp +12 Cleaning up request 5 ID 89 with timestamp +12 Cleaning up request 6 ID 90 with timestamp +12 Cleaning up request 7 ID 91 with timestamp +12 Waking up in 1.0 seconds. Cleaning up request 8 ID 92 with timestamp +12 Waking up in 0.5 seconds. Cleaning up request 9 ID 93 with timestamp +13 Cleaning up request 10 ID 94 with timestamp +13 Cleaning up request 11 ID 95 with timestamp +13 Cleaning up request 12 ID 96 with timestamp +13 Cleaning up request 13 ID 97 with timestamp +13 Cleaning up request 14 ID 98 with timestamp +13 Cleaning up request 15 ID 99 with timestamp +13 Cleaning up request 16 ID 100 with timestamp +13 Waking up in 1.0 seconds. Cleaning up request 17 ID 101 with timestamp +13 Waking up in 0.6 seconds. Cleaning up request 18 ID 102 with timestamp +15 Cleaning up request 19 ID 103 with timestamp +15 Cleaning up request 20 ID 104 with timestamp +15 Cleaning up request 21 ID 105 with timestamp +15 Cleaning up request 22 ID 106 with timestamp +15 Cleaning up request 23 ID 107 with timestamp +15 Cleaning up request 24 ID 108 with timestamp +15 Cleaning up request 25 ID 109 with timestamp +15 Waking up in 1.0 seconds. Cleaning up request 26 ID 110 with timestamp +15 Ready to process requests. To me, it looks like the edirectory password is not getting prompted for properly, but I don't know where to fix that. Any guidance to what we have missed will be greatly appreciated. (if the config files are needed, please let me know and I will post) Thanks in advance. Brian

9 17

backslash and expansion variable quirk in line log format string
by Jason Rankin 13 Apr '15

13 Apr '15

Hi Everyone, I am doing some radius sysloging via the linelog module for accounting requests which is working well except for a string format quirk - my module config is below. I'm trying to get the logged message to be in the format of foo\<username> where foo is only relevant to the device reading the syslog messages and is not a radius login realm. However, foo\\%{User-Name} results in a logged message of "foo\%{User-name}" instead of "foo\fred" - the \% is being interpreted as a control code. If there is any character between the '\' and the '%' it works correctly and logs "foo\fred". Is there any string format configuration that will result in 'foo\fred' being logged - using %{User-Name} - without an inserted space/char in the middle ? I don't seem to be able to find a format that works. ie %{User-Name} is "fred" "foo\\%{User-Name}", logs "foo\%{User-Name}" to syslog "foo\\ %{User-Name}" - space between '\' and '%' - logs "foo\ fred" to syslog, with a space in the string Module config: linelog SyslogAccountingtoPaloAlto { filename = "syslog" format = "This is a log message for %{User-Name}" reference = "Accounting-Request.%{%{Acct-Status-Type}:-unknown}" Access-Request = "Requested access: %{User-Name}" Access-Reject = "Rejected access: %{User-Name}" Access-Challenge = "Sent challenge: %{User-Name}" foo { bar = "Example log. Please ignore" } Accounting-Request { Start = "Radius Acct Start: Username:%{User-Name}" Stop = "Radius Acct Stop: Username:%{User-Name}" Interim-Update = "Radius Interim-Update: Username:foo\\%{User-Name}" # Don't log anything for these packets. Alive = "" Accounting-On = "" Accounting-Off = "" # don't log anything for other Acct-Status-Types. unknown = "" } } Thanks heaps Jason Rankin

4 5

Issues with rlm_cache_memcached in 3.0.7
by Kyle Birkeland 13 Apr '15

13 Apr '15

Hello, I'm trying to get rlm_cache_memcached working, but I'm having some issues with freeradius merging the values from memcached - all my values get truncated. Am I doing it wrong or is this a bug? I've attached the full output of radiusd -X, but I've pasted relevant sections below. Creating the cache entry: (0) eduroam_inner_cache: EXPAND %{User-Name} (0) eduroam_inner_cache: --> asdf(a)utk.edu rlm_cache (eduroam_inner_cache): Reserved connection (4) (0) eduroam_inner_cache: No cache entry found for "asdf(a)utk.edu" (0) eduroam_inner_cache: Creating new cache entry (0) eduroam_inner_cache: request:Stripped-User-Name = &Stripped-User-Name -> 'asdf' (0) eduroam_inner_cache: request:Realm = &Realm -> 'utk.edu' (0) eduroam_inner_cache: control:Aruba-User-Role := &Aruba-User-Role -> 'eduroam-student' (0) eduroam_inner_cache: EXPAND Cache last updated at %t (0) eduroam_inner_cache: --> Cache last updated at Mon Apr 13 16:24:23 2015 (0) eduroam_inner_cache: reply:Reply-Message += "Cache last updated at Mon Apr 13 16:24:23 2015" (0) eduroam_inner_cache: Merging cache entry into request (0) eduroam_inner_cache: &control:Aruba-User-Role := 'eduroam-student' (0) eduroam_inner_cache: &request:Stripped-User-Name = 'asdf' (0) eduroam_inner_cache: &request:Realm = 'utk.edu' (0) eduroam_inner_cache: &reply:Reply-Message += 'Cache last updated at Mon Apr 13 16:24:23 2015' (0) eduroam_inner_cache: Commited entry, TTL 14400 seconds rlm_cache (eduroam_inner_cache): Released connection (4) (0) [eduroam_inner_cache] = updated Reading and merging from the cache: (1) update control { (1) &Cache-Read-Only = yes (1) &Cache-Merge = yes (1) } # update control = noop (1) } # else = noop (1) eduroam_inner_cache: EXPAND %{User-Name} (1) eduroam_inner_cache: --> asdf(a)utk.edu rlm_cache (eduroam_inner_cache): Reserved connection (4) (1) eduroam_inner_cache: Retrieved 223 bytes from memcached (1) eduroam_inner_cache: &Cache-Expires = 1428971063 &Cache-Created = 1428956663 &control:Aruba-User-Role := 'eduroam-student' &Stripped-User-Name = 'asdf' &Realm = 'utk.edu' &reply:Reply-Message += 'Cache last updated at Mon Apr 13 16:24:23 2015' (1) eduroam_inner_cache: Found entry for "asdf(a)utk.edu" (1) eduroam_inner_cache: Merging cache entry into request (1) eduroam_inner_cache: &control:Aruba-User-Role = '' (1) eduroam_inner_cache: &request:Stripped-User-Name = '' (1) eduroam_inner_cache: &request:Realm = '' (1) eduroam_inner_cache: &reply:Reply-Message = '' rlm_cache (eduroam_inner_cache): Released connection (4) (1) [eduroam_inner_cache] = ok Thanks, Kyle Birkeland kbirkela(a)utk.edu

2 3

Usernames with escape sequences
by James Sumners 13 Apr '15

13 Apr '15

I have Freeradius authenticating to an Active Directory system via ntlm_auth. When a username in the format "foobar\jdoe" comes in, where "foobar" is the domain and "jdoe" is the real username, the authentication succeeds just fine. But if username is "foobar\tdoe" then it gets expanded to "foobar doe". Here's some real output where the passed in username was "CCSU\tstudent": ``` (0) mschap : Client is using MS-CHAPv1 with NT-Password (0) mschap : Executing: "/bin/ntlm_auth --request-nt-key --username=%{%{mschap:User-Name}:-None} --domain=%{%{mschap:NT-Domain}:-None} --challenge=%{%{mschap:Challenge}:-00} --nt-response=%{%{mschap:NT-Response}:-00}" (0) mschap : expand: "--username=%{%{mschap:User-Name}:-None}" -> '--username=CCSU student' (0) mschap : No NT-Domain was found in the User-Name. (0) mschap : expand: "--domain=%{%{mschap:NT-Domain}:-None}" -> '--domain=' (0) mschap : mschap1: ac (0) mschap : expand: "--challenge=%{%{mschap:Challenge}:-00}" -> '--challenge=ac132ce03cba1933' (0) mschap : expand: "--nt-response=%{%{mschap:NT-Response}:-00}" -> '--nt-response=ff768eafb00738e62a3a92e103bf5c7baa7d926da2248b88' (0) mschap : Program returned code (1): Logon failure (0xc000006d) (0) mschap : External script failed. (0) ERROR: mschap : External script says: Logon failure (0xc000006d) ``` How do I prevent the escape sequence from being expanded?

5 11

Autentication
by sandy.napoles＠eccmg.cupet.cu 13 Apr '15

13 Apr '15

Hello list is possible autenticate freeradius with samba4...somebody can help me

2 1

Possible Login Times - Restrictions?
by Tobias Hansen 13 Apr '15

13 Apr '15

Hey there, it seems that there's a problem with the maximum possible login times per user. Some users encounter some trouble with their allowed timespan on sunday. Logfile says: Mar 15 20:12:51 logportalauth[72261]: Zone: restricted - FAILURE: XXXXXXX, XX:XX:XX:XX:XX, 172.16.107.138, You are calling outside your allowed timespan The freeradius settings: Username xxx Password xxx Discription 3Std/Tag Possible Login Times Mo1300-1420,Mo1630-2115,Tu1130-1420,Tu1630-2115,We1300-1420,We1630-2115,Th1300-1420,Th1630-2115,Fr1500-2230,Sa1000-2230,Su1000-2115 Amount of Time: 180 After some research we found that this issue occures for every user with more than 10 different login times. Do you know anything about this? And, if so, is there a workaround available? Our setup is a hardware pfSense (Netgate) 2.2-Release with freeradius2 ver. 2.1.12_1/2.2.6_3 pkg v1.6.10 Thank you in advance! Mit freundlichen Grüßen Tobias Hansen NordKonzept GmbH Süderstr. 35 DE-25746 Heide/Holst. Telefon: +49 (0) 481 599 81 92 Telefax: +49 (0) 481 783 92 Web: http://www.nordkonzept.de<http://www.nordkonzept.de/> Zuständiges Amtsgericht: Meldorf Umsatzsteuer ID: DE275460911 Handelsregister: HRB 9076, Pinneberg Geschäftsführer: Oliver Carstensen Rechtliche Hinweise: Diese elektronische Nachricht enthält vertrauliche Informationen, die nur für die im Text bezeichneten Personen bestimmt sind. Die Nachricht ist durch das Briefgeheimnis geschützt und unterliegt gegebenenfalls den Regeln zum Schutz der Vertraulichkeit. Jede Benutzung, Versendung, Herstellung von Kopien oder Veröffentlichung durch andere Personen ist ohne Zustimmung des Absenders untersagt. Wenn Sie diese Nachricht irrtümlich erhalten haben, bitten wir Sie höflichst, sie auf Ihren Systemen zu löschen und den Absender umgehend zu benachrichtigen. This electronic mail transmission contains confidential information intended only for the person(s) named. It is subject to the laws of mail secrecy and may be protected by legal privileges. Any use, distribution, copying or disclosure by another person is strictly prohibited without the consent of the sender. If this transmission has been received in error, you are kindly requested to delete it from your system and to contact the sender immediately.

2 1

LDAP server
by Adam Bishop 13 Apr '15

13 Apr '15

I can probably fix this with systemD somehow, but is it possible to configure FreeRADIUS to start even if its LDAP server is unavailable? They both exist on the same machine, however LDAP is a *lot* slower than FreeRADIUS to get going. I don't want to configure a second LDAP server if I can avoid it - the ldap servers sibling (which would be online) is a high latency VPN away. Regards, Adam Bishop gpg: 0x6609D460 jisc.ac.uk --- radiusd: FreeRADIUS Version 3.0.4, for host x86_64-redhat-linux-gnu, built on Mar 5 2015 at 23:41:36 Copyright (C) 1999-2014 The FreeRADIUS server project and contributors There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE You may redistribute copies of FreeRADIUS under the terms of the GNU General Public License For more information about these matters, see the file named COPYRIGHT Starting - reading configuration files ... including dictionary file /usr/share/freeradius/dictionary including dictionary file /usr/share/freeradius/dictionary.dhcp including dictionary file /usr/share/freeradius/dictionary.vqp including dictionary file /etc/raddb/dictionary including configuration file /etc/raddb/radiusd.conf including configuration file /etc/raddb/proxy.conf including configuration file /etc/raddb/clients.conf including files in directory /etc/raddb/mods-enabled/ including configuration file /etc/raddb/mods-enabled/always including configuration file /etc/raddb/mods-enabled/attr_filter including configuration file /etc/raddb/mods-enabled/cache_eap including configuration file /etc/raddb/mods-enabled/chap including configuration file /etc/raddb/mods-enabled/detail including configuration file /etc/raddb/mods-enabled/detail.log including configuration file /etc/raddb/mods-enabled/dhcp including configuration file /etc/raddb/mods-enabled/digest including configuration file /etc/raddb/mods-enabled/dynamic_clients including configuration file /etc/raddb/mods-enabled/eap including configuration file /etc/raddb/mods-enabled/echo including configuration file /etc/raddb/mods-enabled/exec including configuration file /etc/raddb/mods-enabled/expiration including configuration file /etc/raddb/mods-enabled/expr including configuration file /etc/raddb/mods-enabled/files including configuration file /etc/raddb/mods-enabled/linelog including configuration file /etc/raddb/mods-enabled/logintime including configuration file /etc/raddb/mods-enabled/mschap including configuration file /etc/raddb/mods-enabled/ntlm_auth including configuration file /etc/raddb/mods-enabled/pap including configuration file /etc/raddb/mods-enabled/passwd including configuration file /etc/raddb/mods-enabled/preprocess including configuration file /etc/raddb/mods-enabled/radutmp including configuration file /etc/raddb/mods-enabled/realm including configuration file /etc/raddb/mods-enabled/replicate including configuration file /etc/raddb/mods-enabled/soh including configuration file /etc/raddb/mods-enabled/sradutmp including configuration file /etc/raddb/mods-enabled/unix including configuration file /etc/raddb/mods-enabled/utf8 including configuration file /etc/raddb/mods-enabled/krb5 including configuration file /etc/raddb/mods-enabled/ldap including configuration file /etc/raddb/mods-enabled/unpack including files in directory /etc/raddb/policy.d/ including configuration file /etc/raddb/policy.d/accounting including configuration file /etc/raddb/policy.d/canonicalization including configuration file /etc/raddb/policy.d/control including configuration file /etc/raddb/policy.d/cui including configuration file /etc/raddb/policy.d/dhcp including configuration file /etc/raddb/policy.d/eap including configuration file /etc/raddb/policy.d/filter including configuration file /etc/raddb/policy.d/operator-name including configuration file /etc/raddb/policy.d/debug including files in directory /etc/raddb/sites-enabled/ including configuration file /etc/raddb/sites-enabled/default including configuration file /etc/raddb/sites-enabled/inner-tunnel including configuration file /etc/raddb/sites-enabled/observium including configuration file /etc/raddb/sites-enabled/infr main { security { user = "radiusd" group = "radiusd" allow_core_dumps = no } } main { name = "radiusd" prefix = "/usr" localstatedir = "/var" sbindir = "/usr/sbin" logdir = "/var/log/radius" run_dir = "/var/run/radiusd" libdir = "/usr/lib64/freeradius" radacctdir = "/var/log/radius/radacct" hostname_lookups = no max_request_time = 30 cleanup_delay = 5 max_requests = 1024 pidfile = "/var/run/radiusd/radiusd.pid" checkrad = "/usr/sbin/checkrad" debug_level = 0 proxy_requests = yes log { stripped_names = no auth = no auth_badpass = no auth_goodpass = no colourise = yes msg_denied = "You are already logged in - access denied" } security { max_attributes = 200 reject_delay = 1 status_server = yes } } radiusd: #### Loading Realms and Home Servers #### proxy server { retry_delay = 5 retry_count = 3 default_fallback = no dead_time = 120 wake_all_if_all_dead = no } home_server localhost { ipaddr = 127.0.0.1 port = 1812 type = "auth" secret = <<< secret >>> response_window = 20.000000 response_timeouts = 1 max_outstanding = 65536 zombie_period = 40 status_check = "status-server" ping_interval = 30 check_interval = 30 check_timeout = 4 num_answers_to_alive = 3 revive_interval = 120 coa { irt = 2 mrt = 16 mrc = 5 mrd = 30 } limit { max_connections = 16 max_requests = 0 lifetime = 0 idle_timeout = 0 } } home_server_pool my_auth_failover { type = fail-over home_server = localhost } realm example.com { auth_pool = my_auth_failover } realm LOCAL { } radiusd: #### Loading Clients #### client localhost { ipaddr = 127.0.0.1 require_message_authenticator = no secret = <<< secret >>> nas_type = "other" proto = "*" limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } client atl-cmm-001 { ipaddr = atl-cmm-001 IPv4 address [] require_message_authenticator = no secret = <<< secret >>> virtual_server = "observium" limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } client atl-switch-001 { ipaddr = require_message_authenticator = no secret = <<< secret >>> virtual_server = "infr" limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } client swi-switch-001 { ipaddr = require_message_authenticator = no secret = <<< secret >>> virtual_server = "infr" limit { max_connections = 16 lifetime = 0 idle_timeout = 30 } } radiusd: #### Instantiating modules #### instantiate { } modules { # Loaded module rlm_always # Instantiating module "reject" from file /etc/raddb/mods-enabled/always always reject { rcode = "reject" simulcount = 0 mpp = no } # Instantiating module "fail" from file /etc/raddb/mods-enabled/always always fail { rcode = "fail" simulcount = 0 mpp = no } # Instantiating module "ok" from file /etc/raddb/mods-enabled/always always ok { rcode = "ok" simulcount = 0 mpp = no } # Instantiating module "handled" from file /etc/raddb/mods-enabled/always always handled { rcode = "handled" simulcount = 0 mpp = no } # Instantiating module "invalid" from file /etc/raddb/mods-enabled/always always invalid { rcode = "invalid" simulcount = 0 mpp = no } # Instantiating module "userlock" from file /etc/raddb/mods-enabled/always always userlock { rcode = "userlock" simulcount = 0 mpp = no } # Instantiating module "notfound" from file /etc/raddb/mods-enabled/always always notfound { rcode = "notfound" simulcount = 0 mpp = no } # Instantiating module "noop" from file /etc/raddb/mods-enabled/always always noop { rcode = "noop" simulcount = 0 mpp = no } # Instantiating module "updated" from file /etc/raddb/mods-enabled/always always updated { rcode = "updated" simulcount = 0 mpp = no } # Loaded module rlm_attr_filter # Instantiating module "attr_filter.post-proxy" from file /etc/raddb/mods-enabled/attr_filter attr_filter attr_filter.post-proxy { filename = "/etc/raddb/mods-config/attr_filter/post-proxy" key = "%{Realm}" relaxed = no } reading pairlist file /etc/raddb/mods-config/attr_filter/post-proxy # Instantiating module "attr_filter.pre-proxy" from file /etc/raddb/mods-enabled/attr_filter attr_filter attr_filter.pre-proxy { filename = "/etc/raddb/mods-config/attr_filter/pre-proxy" key = "%{Realm}" relaxed = no } reading pairlist file /etc/raddb/mods-config/attr_filter/pre-proxy # Instantiating module "attr_filter.access_reject" from file /etc/raddb/mods-enabled/attr_filter attr_filter attr_filter.access_reject { filename = "/etc/raddb/mods-config/attr_filter/access_reject" key = "%{User-Name}" relaxed = no } reading pairlist file /etc/raddb/mods-config/attr_filter/access_reject # Instantiating module "attr_filter.access_challenge" from file /etc/raddb/mods-enabled/attr_filter attr_filter attr_filter.access_challenge { filename = "/etc/raddb/mods-config/attr_filter/access_challenge" key = "%{User-Name}" relaxed = no } reading pairlist file /etc/raddb/mods-config/attr_filter/access_challenge # Instantiating module "attr_filter.accounting_response" from file /etc/raddb/mods-enabled/attr_filter attr_filter attr_filter.accounting_response { filename = "/etc/raddb/mods-config/attr_filter/accounting_response" key = "%{User-Name}" relaxed = no } reading pairlist file /etc/raddb/mods-config/attr_filter/accounting_response # Loaded module rlm_cache # Instantiating module "cache_eap" from file /etc/raddb/mods-enabled/cache_eap cache cache_eap { key = "%{%{control:State}:-%{%{reply:State}:-%{State}}}" ttl = 15 max_entries = 16384 epoch = 0 add_stats = no } # Loaded module rlm_chap # Instantiating module "chap" from file /etc/raddb/mods-enabled/chap # Loaded module rlm_detail # Instantiating module "detail" from file /etc/raddb/mods-enabled/detail detail { filename = "/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/detail-%Y%m%d" header = "%t" permissions = 384 locking = no log_packet_header = no } # Instantiating module "auth_log" from file /etc/raddb/mods-enabled/detail.log detail auth_log { filename = "/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/auth-detail-%Y%m%d" header = "%t" permissions = 384 locking = no log_packet_header = no } rlm_detail (auth_log): 'User-Password' suppressed, will not appear in detail output # Instantiating module "reply_log" from file /etc/raddb/mods-enabled/detail.log detail reply_log { filename = "/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/reply-detail-%Y%m%d" header = "%t" permissions = 384 locking = no log_packet_header = no } # Instantiating module "pre_proxy_log" from file /etc/raddb/mods-enabled/detail.log detail pre_proxy_log { filename = "/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/pre-proxy-detail-%Y%m%d" header = "%t" permissions = 384 locking = no log_packet_header = no } # Instantiating module "post_proxy_log" from file /etc/raddb/mods-enabled/detail.log detail post_proxy_log { filename = "/var/log/radius/radacct/%{%{Packet-Src-IP-Address}:-%{Packet-Src-IPv6-Address}}/post-proxy-detail-%Y%m%d" header = "%t" permissions = 384 locking = no log_packet_header = no } # Loaded module rlm_dhcp # Instantiating module "dhcp" from file /etc/raddb/mods-enabled/dhcp # Loaded module rlm_digest # Instantiating module "digest" from file /etc/raddb/mods-enabled/digest # Loaded module rlm_dynamic_clients # Instantiating module "dynamic_clients" from file /etc/raddb/mods-enabled/dynamic_clients # Loaded module rlm_eap # Instantiating module "eap" from file /etc/raddb/mods-enabled/eap eap { default_eap_type = "ttls" timer_expire = 60 ignore_unknown_eap_types = no mod_accounting_username_bug = no max_sessions = 4096 } # Linked to sub-module rlm_eap_md5 # Linked to sub-module rlm_eap_leap # Linked to sub-module rlm_eap_gtc gtc { challenge = "Password: " auth_type = "PAP" } # Linked to sub-module rlm_eap_tls tls { tls = "tls-common" } tls-config tls-common { rsa_key_exchange = no dh_key_exchange = yes rsa_key_length = 512 dh_key_length = 512 verify_depth = 0 ca_path = "/etc/raddb/certs" pem_file_type = yes private_key_file = "/etc/raddb/certs/server.pem" certificate_file = "/etc/raddb/certs/server.pem" ca_file = "/etc/raddb/certs/ca.pem" private_key_password = <<< secret >>> dh_file = "/etc/raddb/certs/dh" fragment_size = 1024 include_length = yes check_crl = no cipher_list = "DEFAULT" ecdh_curve = "prime256v1" cache { enable = yes lifetime = 24 max_entries = 255 } verify { } ocsp { enable = no override_cert_url = yes url = "http://127.0.0.1/ocsp/" use_nonce = yes timeout = 0 softfail = yes } } # Linked to sub-module rlm_eap_ttls ttls { tls = "tls-common" default_eap_type = "md5" copy_request_to_tunnel = no use_tunneled_reply = no virtual_server = "inner-tunnel" include_length = yes require_client_cert = no } Using cached TLS configuration from previous invocation # Linked to sub-module rlm_eap_peap peap { tls = "tls-common" default_method = "mschapv2" copy_request_to_tunnel = no use_tunneled_reply = no proxy_tunneled_request_as_eap = yes virtual_server = "inner-tunnel" soh = no require_client_cert = no } Using cached TLS configuration from previous invocation # Linked to sub-module rlm_eap_mschapv2 mschapv2 { with_ntdomain_hack = no send_error = no } # Loaded module rlm_exec # Instantiating module "echo" from file /etc/raddb/mods-enabled/echo exec echo { wait = yes program = "/bin/echo %{User-Name}" input_pairs = "request" output_pairs = "reply" shell_escape = yes } # Instantiating module "exec" from file /etc/raddb/mods-enabled/exec exec { wait = no input_pairs = "request" shell_escape = yes timeout = 10 } # Loaded module rlm_expiration # Instantiating module "expiration" from file /etc/raddb/mods-enabled/expiration # Loaded module rlm_expr # Instantiating module "expr" from file /etc/raddb/mods-enabled/expr expr { safe_characters = "@abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789.-_: /" } # Loaded module rlm_files # Instantiating module "files" from file /etc/raddb/mods-enabled/files files { filename = "/etc/raddb/mods-config/files/authorize" usersfile = "/etc/raddb/mods-config/files/authorize" acctusersfile = "/etc/raddb/mods-config/files/accounting" preproxy_usersfile = "/etc/raddb/mods-config/files/pre-proxy" compat = "cistron" } reading pairlist file /etc/raddb/mods-config/files/authorize [/etc/raddb/mods-config/files/authorize]:1 Cistron compatibility checks for entry DEFAULT ... Changing 'Auth-Type =' to 'Auth-Type +=' [/etc/raddb/mods-config/files/authorize]:182 Cistron compatibility checks for entry DEFAULT ... [/etc/raddb/mods-config/files/authorize]:189 Cistron compatibility checks for entry DEFAULT ... [/etc/raddb/mods-config/files/authorize]:196 Cistron compatibility checks for entry DEFAULT ... reading pairlist file /etc/raddb/mods-config/files/authorize [/etc/raddb/mods-config/files/authorize]:1 Cistron compatibility checks for entry DEFAULT ... Changing 'Auth-Type =' to 'Auth-Type +=' [/etc/raddb/mods-config/files/authorize]:182 Cistron compatibility checks for entry DEFAULT ... [/etc/raddb/mods-config/files/authorize]:189 Cistron compatibility checks for entry DEFAULT ... [/etc/raddb/mods-config/files/authorize]:196 Cistron compatibility checks for entry DEFAULT ... reading pairlist file /etc/raddb/mods-config/files/accounting reading pairlist file /etc/raddb/mods-config/files/pre-proxy # Loaded module rlm_linelog # Instantiating module "linelog" from file /etc/raddb/mods-enabled/linelog linelog { filename = "/var/log/radius/linelog" permissions = 384 format = "This is a log message for %{User-Name}" reference = "messages.%{%{Packet-Type}:-default}" } # Instantiating module "log_accounting" from file /etc/raddb/mods-enabled/linelog linelog log_accounting { filename = "/var/log/radius/linelog-accounting" permissions = 384 format = "" reference = "Accounting-Request.%{%{Acct-Status-Type}:-unknown}" } # Loaded module rlm_logintime # Instantiating module "logintime" from file /etc/raddb/mods-enabled/logintime logintime { minimum_timeout = 60 } # Loaded module rlm_mschap # Instantiating module "mschap" from file /etc/raddb/mods-enabled/mschap mschap { use_mppe = yes require_encryption = no require_strong = no with_ntdomain_hack = yes passchange { } allow_retry = yes } # Instantiating module "ntlm_auth" from file /etc/raddb/mods-enabled/ntlm_auth exec ntlm_auth { wait = yes program = "/path/to/ntlm_auth --request-nt-key --domain=MYDOMAIN --username=%{mschap:User-Name} --password=%{User-Password}" shell_escape = yes } # Loaded module rlm_pap # Instantiating module "pap" from file /etc/raddb/mods-enabled/pap pap { normalise = yes } # Loaded module rlm_passwd # Instantiating module "etc_passwd" from file /etc/raddb/mods-enabled/passwd passwd etc_passwd { filename = "/etc/passwd" format = "*User-Name:Crypt-Password:" delimiter = ":" ignore_nislike = no ignore_empty = yes allow_multiple_keys = no hash_size = 100 } rlm_passwd: nfields: 3 keyfield 0(User-Name) listable: no # Loaded module rlm_preprocess # Instantiating module "preprocess" from file /etc/raddb/mods-enabled/preprocess preprocess { huntgroups = "/etc/raddb/mods-config/preprocess/huntgroups" hints = "/etc/raddb/mods-config/preprocess/hints" with_ascend_hack = no ascend_channels_per_line = 23 with_ntdomain_hack = no with_specialix_jetstream_hack = no with_cisco_vsa_hack = no with_alvarion_vsa_hack = no } reading pairlist file /etc/raddb/mods-config/preprocess/huntgroups reading pairlist file /etc/raddb/mods-config/preprocess/hints # Loaded module rlm_radutmp # Instantiating module "radutmp" from file /etc/raddb/mods-enabled/radutmp radutmp { filename = "/var/log/radius/radutmp" username = "%{User-Name}" case_sensitive = yes check_with_nas = yes permissions = 384 caller_id = yes } # Loaded module rlm_realm # Instantiating module "IPASS" from file /etc/raddb/mods-enabled/realm realm IPASS { format = "prefix" delimiter = "/" ignore_default = no ignore_null = no } # Instantiating module "suffix" from file /etc/raddb/mods-enabled/realm realm suffix { format = "suffix" delimiter = "@" ignore_default = no ignore_null = no } # Instantiating module "realmpercent" from file /etc/raddb/mods-enabled/realm realm realmpercent { format = "suffix" delimiter = "%" ignore_default = no ignore_null = no } # Instantiating module "ntdomain" from file /etc/raddb/mods-enabled/realm realm ntdomain { format = "prefix" delimiter = "\" ignore_default = no ignore_null = no } # Loaded module rlm_replicate # Instantiating module "replicate" from file /etc/raddb/mods-enabled/replicate # Loaded module rlm_soh # Instantiating module "soh" from file /etc/raddb/mods-enabled/soh soh { dhcp = yes } # Instantiating module "sradutmp" from file /etc/raddb/mods-enabled/sradutmp radutmp sradutmp { filename = "/var/log/radius/sradutmp" username = "%{User-Name}" case_sensitive = yes check_with_nas = yes permissions = 420 caller_id = no } # Loaded module rlm_unix # Instantiating module "unix" from file /etc/raddb/mods-enabled/unix unix { radwtmp = "/var/log/radius/radwtmp" } # Loaded module rlm_utf8 # Instantiating module "utf8" from file /etc/raddb/mods-enabled/utf8 # Loaded module rlm_krb5 # Instantiating module "krb5" from file /etc/raddb/mods-enabled/krb5 krb5 { keytab = "/var/lib/radiusd/krb5.keytab" service_principal = "radius/atl-ipa-001" } Using MIT Kerberos library rlm_krb5 (krb5): Using service principal "" rlm_krb5 (krb5): Using keytab "FILE:/var/lib/radiusd/krb5.keytab" rlm_krb5 (krb5): Initialising connection pool pool { start = 10 min = 4 max = 10 spare = 3 uses = 0 lifetime = 0 cleanup_interval = 30 idle_timeout = 60 retry_delay = 1 spread = no } rlm_krb5 (krb5): Opening additional connection (0) rlm_krb5 (krb5): Opening additional connection (1) rlm_krb5 (krb5): Opening additional connection (2) rlm_krb5 (krb5): Opening additional connection (3) rlm_krb5 (krb5): Opening additional connection (4) rlm_krb5 (krb5): Opening additional connection (5) rlm_krb5 (krb5): Opening additional connection (6) rlm_krb5 (krb5): Opening additional connection (7) rlm_krb5 (krb5): Opening additional connection (8) rlm_krb5 (krb5): Opening additional connection (9) # Loaded module rlm_ldap # Instantiating module "ldap" from file /etc/raddb/mods-enabled/ldap ldap { server = "atl-ipa-001" port = 389 password = <<< secret >>> identity = "" user { filter = "(uid=%{%{Stripped-User-Name}:-%{User-Name}})" scope = "sub" base_dn = "" access_positive = yes } group { filter = "(objectClass=posixGroup)" scope = "sub" base_dn = "" name_attribute = "cn" membership_attribute = "memberOf" membership_filter = "(|(member=%{control:Ldap-UserDn})(memberUid=%{%{Stripped-User-Name}:-%{User-Name}}))" cacheable_name = no cacheable_dn = no } client { filter = "(objectClass=frClient)" scope = "sub" base_dn = "" attribute { identifier = "radiusClientIdentifier" shortname = "cn" secret = "radiusClientSecret" } } profile { filter = "(&)" } options { ldap_debug = 40 chase_referrals = yes rebind = yes net_timeout = 1 res_timeout = 20 srv_timelimit = 20 idle = 60 probes = 3 interval = 3 } tls { start_tls = no } } rlm_ldap: Falling back to build time libldap version info. Query for LDAP_OPT_API_INFO returned: -1 rlm_ldap: libldap vendor: OpenLDAP version: 20439 accounting { reference = "%{tolower:type.%{Acct-Status-Type}}" } post-auth { reference = "." } rlm_ldap (ldap): Initialising connection pool pool { start = 5 min = 4 max = 10 spare = 3 uses = 0 lifetime = 0 cleanup_interval = 30 idle_timeout = 60 retry_delay = 1 spread = no } rlm_ldap (ldap): Opening additional connection (0) rlm_ldap (ldap): Connecting to atl-ipa-001:389 rlm_ldap (ldap): Bind with to atl-ipa-001:389 failed: Can't contact LDAP server rlm_ldap (ldap): Opening connection failed (0) rlm_ldap (ldap): Removing connection pool /etc/raddb/mods-enabled/ldap[8]: Instantiation failed for module "ldap" Jisc is a registered charity (number 1149740) and a company limited by guarantee which is registered in England under Company No. 5747339, VAT No. GB 197 0632 86. Jisc’s registered office is: One Castlepark, Tower Hill, Bristol, BS2 0JA. T 0203 697 5800. Jisc Services Limited is a wholly owned Jisc subsidiary and a company limited by guarantee which is registered in England under company number 2881024, VAT number GB 197 0632 86. The registered office is: One Castle Park, Tower Hill, Bristol BS2 0JA. T 0203 697 5800.

3 3