- Freeradius-Users - lists.freeradius.org

Configuring FreeRADIUS to use ntlm_auth for MS-CHAP
by Martin Ubank 21 Oct '11

21 Oct '11

I've been following the FreeRadius Deployment guide http://deployingradius.com/documents/configuration/active_directory.html The following software is installed on a Centos 6 VM: - Samba 3.5.4, Freeradius 2.1.9, wpa_supplicant-0.7.3, gcc v4.4.4-13, openssl, winbind. I successfully performed basic configuration tests with the 'eapol_test' command for: - PAP, EAP, EAP-TLS, EAP-TTLS, EAP-MD5 & EAP-MSCHAPv5. I've created production certificates & successfully tested for the above protocols. Installed Kerberos 1.8.2 & tested that successfully. I started to configure FreeRadius with AD and successfully tested it to use ntlm_auth. I've got to the final stage "Configuring FreeRADIUS to use ntlm_auth for MS-CHAP" in the deployment process. This stage says: 1) "... delete the testing entry used above from the users file, ...", which I've done. 2) "... fine (sic) the mschap module in raddb/modules/mschap file, and look for the line containing ntlm_auth = . It ... should be uncommented, ...", which I've done. 3) "Start the server ..." I ran 'radiusd -X'. 4) "... and use a test client to send an MS-CHAP authentication request." I've used the command 'eapol_test -c peap-mschapv2-cert-ntlm_auth.conf -s testing123'. I can see from the 'radiusd -X' output that FreeRadius is not using MS-CHAP correctly: <snip> [eap] processing type mschapv2 [mschapv2] +- entering group MS-CHAP {...} [mschap] No Cleartext-Password configured. Cannot create LM-Password. [mschap] No Cleartext-Password configured. Cannot create NT-Password. [mschap] Told to do MS-CHAPv2 for USERNAME with NT-Password [mschap] FAILED: No NT/LM-Password. Cannot perform authentication. [mschap] FAILED: MS-CHAP2-Response is incorrect ++[mschap] returns reject <snip> The 'eapol_test' output reflects this: <snip> EAP-PEAP: Selected Phase 2 EAP vendor 0 method 26 EAP-MSCHAPV2: RX identifier 8 mschapv2_id 8 EAP-MSCHAPV2: Received challenge EAP-MSCHAPV2: Authentication Servername - hexdump_ascii(len=11): 65 64 75 72 6f 61 6d 74 65 73 74 USERNAME EAP-MSCHAPV2: Generating Challenge Response MSCHAPV2: Identity - hexdump_ascii(len=11): 65 64 75 72 6f 61 6d 74 65 73 74 USERNAME MSCHAPV2: Username - hexdump_ascii(len=11): 65 64 75 72 6f 61 6d 74 65 73 74 USERNAME MSCHAPV2: auth_challenge - hexdump(len=16): a5 e6 9e fa 6e 1f ec 2f 0b b6 a3 96 ef 45 15 32 MSCHAPV2: peer_challenge - hexdump(len=16): 44 31 43 ff 2f 12 5b 25 b5 eb fb 59 6f 8d 2a a9 MSCHAPV2: username - hexdump_ascii(len=11): 65 64 75 72 6f 61 6d 74 65 73 74 USERNAME MSCHAPV2: password - hexdump_ascii(len=20): 77 6f 72 6b 6d 61 6e 20 74 6f 64 61 79 20 61 72 PASSWORD 6e 69 63 61 MSCHAPV2: NT Response - hexdump(len=24): 66 67 95 3d 56 d6 ab b4 ab ba 64 bf 6c db 8b 51 77 ad 3e bc 96 26 7c 7a MSCHAPV2: Auth Response - hexdump(len=20): f0 95 4d 86 ee 82 8f c0 12 84 cc a7 d0 72 fb e6 95 b3 ef d1 MSCHAPV2: Master Key - hexdump(len=16): 31 8d ae c0 3d e1 42 0f ae 05 bc f0 72 da 98 72 EAP-MSCHAPV2: TX identifier 8 mschapv2_id 8 (response) EAP-PEAP: Encrypting Phase 2 data - hexdump(len=70): 02 08 00 46 1a 02 08 00 41 31 44 31 43 ff 2f 12 5b 25 b5 eb fb 59 6f 8d 2a a9 00 00 00 00 00 00 00 00 66 67 95 3d 56 d6 ab b4 ab ba 64 bf 6c db 8b 51 77 ad 3e bc 96 26 7c 7a 00 65 64 75 72 6f 61 6d 74 65 73 74 <snip> RADIUS packet matching with station decapsulated EAP packet (code=4 id=9 len=4) from RADIUS server: EAP Failure EAPOL: Received EAP-Packet frame EAPOL: SUPP_BE entering state REQUEST EAPOL: getSuppRsp EAP: EAP entering state RECEIVED EAP: Received EAP-Failure EAP: EAP entering state FAILURE CTRL-EVENT-EAP-FAILURE EAP authentication failed EAPOL: SUPP_PAE entering state HELD EAPOL: SUPP_BE entering state RECEIVE EAPOL: SUPP_BE entering state FAIL EAPOL: SUPP_BE entering state IDLE eapol_sm_cb: success=0 EAPOL: EAP key not available EAP: deinitialize previously used EAP method (25, PEAP) at EAP deinit ENGINE: engine deinit MPPE keys OK: 0 mismatch: 1 FAILURE The peap-mschapv2-cert-ntlm_auth.conf file contains: # # eapol_test -c peap-mschapv2-cert-ntlm_auth.conf -s testing123 # eapol_version=1 fast_reauth=0 network={ key_mgmt=WPA-EAP eap=PEAP identity="USERNAME" # anonymous_identity="anonymous" password="PASSWORD" phase2="auth=MSCHAPV2" priority=10 # # Uncomment the following to perform server certificate validation. ca_cert="/etc/raddb/certs/ca.der" } The file /etc/raddb/modules/mschap contains: # -*- text -*- # # $Id$ # Microsoft CHAP authentication # # This module supports MS-CHAP and MS-CHAPv2 authentication. # It also enforces the SMB-Account-Ctrl attribute. # mschap { #ntlm_auth = "/path/to/ntlm_auth --request-nt-key --username=%{%{Stripped-User-Name}:-%{User-Name:-None}} --challenge=%{mschap:Challenge:-00} --nt-response=%{mschap:NT-Response:-00}" ntlm_auth = "/usr/bin/ntlm_auth --request-nt-key --username=%{mschap:User-Name:-None} --domain=%{%{mschap:NT-Domain}:-CAMPUS} --challenge=%{mschap:Challenge:-00} --nt-response=%{mschap:NT-Response:-00}" } /etc/raddb/users contains (commented lines removed for clarity): # DEFAULT Auth-Type = ntlm_auth # DEFAULT Framed-Protocol == PPP Framed-Protocol = PPP, Framed-Compression = Van-Jacobson-TCP-IP DEFAULT Hint == "CSLIP" Framed-Protocol = SLIP, Framed-Compression = Van-Jacobson-TCP-IP DEFAULT Hint == "SLIP" Framed-Protocol = SLIP /etc/raddb/sites-enabled/default, a link to ../sites-available/default, contains (most commented lines removed): authorize { preprocess chap mschap # digest # wimax # IPASS suffix # ntdomain eap { ok = return } unix files # sql # etc_smbpasswd # ldap # daily # checkval expiration logintime pap # Autz-Type Status-Server { # # } } authenticate { Auth-Type PAP { pap } Auth-Type CHAP { chap } Auth-Type MS-CHAP { mschap } # digest # pam unix # Auth-Type LDAP { # ldap # } eap # Auth-Type eap { # eap { # handled = 1 # } # if (handled && (Response-Packet-Type == Access-Challenge)) { # attr_filter.access_challenge.post-auth # handled # override the "updated" code from attr_filter # } # } ntlm_auth } preacct { preprocess # update request { # FreeRADIUS-Acct-Session-Start-Time = "%{expr: %l - %{%{Acct-Session-Time}:-0} - %{%{Acct-Delay-Time}:-0}}" # } acct_unique # # IPASS suffix # ntdomain files } accounting { detail # daily unix radutmp # sradutmp # main_pool # sql # if (noop) { # ok # } # sql_log # pgsql-voip attr_filter.accounting_response # Acct-Type Status-Server { # # } } session { radutmp # sql } post-auth { # main_pool # reply_log # sql # sql_log # ldap exec # wimax Post-Auth-Type REJECT { # sql attr_filter.access_reject } } pre-proxy { # attr_rewrite # files # attr_filter.pre-proxy # pre_proxy_log } post-proxy { # post_proxy_log # attr_rewrite # attr_filter.post-proxy eap # Post-Proxy-Type Fail { # detail # } } /etc/raddb/sites-enabled/inner-tunnel, a link to ../sites-available/inner-tunnel, contains (commented lines removed): server inner-tunnel { #listen { # ipaddr = 127.0.0.1 # port = 18120 # type = auth #} authorize { chap mschap unix # IPASS suffix # ntdomain update control { Proxy-To-Realm := LOCAL } eap { ok = return } files # sql # etc_smbpasswd # ldap # daily # checkval expiration logintime pap } authenticate { Auth-Type PAP { pap } Auth-Type CHAP { chap } Auth-Type MS-CHAP { mschap } # pam unix # Auth-Type LDAP { # ldap # } eap ntlm_auth } session { radutmp # sql } post-auth { # reply_log # sql # sql_log # ldap Post-Auth-Type REJECT { # sql attr_filter.access_reject } } pre-proxy { # attr_rewrite # files # attr_filter.pre-proxy # pre_proxy_log } post-proxy { # post_proxy_log # attr_rewrite # attr_filter.post-proxy eap # Post-Proxy-Type Fail { # detail # } } } # inner-tunnel server block However, it's not clear to me where the problem lies. I've attached various files to illustrate the problem. Can anyone point me in the direction of a solution? I've not included full versions of the output due to the mailing list's message size limit. Please let me know if I've not included sufficient information to diagnose the problem. Cheers Martin. P.S. I've hidden the actual username & password used.

6 10

Debug: rlm_sqlcounter: No integer found in string ""
by JennyBlunt 20 Oct '11

20 Oct '11

I'm having issues getting my dailycounter, hourlycounter etc. to work properly. Max-All-Session is ok but there seems to be something wrong with the others. The error in debug is: Info: [dailycounter] expand: %{sql:SELECT SUM(AcctSessionTime - GREATEST((1319068800 -UNIX_TIMESTAMP(AcctStartTime)), 0)) FROM radacct WHERE UserName='full' AND UNIX_TIMESTAMP(AcctStartTime) + AcctSessionTime > '1319068800'} -> Debug: rlm_sqlcounter: No integer found in string "" Info: ++[dailycounter] returns noop Debug: rlm_sqlcounter: Entering module authorize code Debug: rlm_sqlcounter: Could not find Check item value pair If run in mysql, I get value = NULL If I remove Unix_timestamp, I get a value but this is incorrect and obviously can't use. Can anyone suggest what I need to do to fix this?? Am using meraki hardware to test but have coovachilli around to test if required. Thanks -- View this message in context: http://freeradius.1045715.n5.nabble.com/Debug-rlm-sqlcounter-No-integer-fou… Sent from the FreeRadius - User mailing list archive at Nabble.com.

1 0

wiki
by Alexandre Chapellon 20 Oct '11

20 Oct '11

Hello, I have tried to update the wiki here: http://wiki.freeradius.org/PopTop The dictionary file that was here caused problem with the lastest radiusplugin-ng and last poptop when using mppe. I found a correct dictionary on the poptop website that solve the problem and wanted to copy it to the wiki. Unfortunately I messed up things and now this page is not readable anymore. I haven't found a way to solve this or to get back to previous version.... Thank you for your help. -- <http://www.horoa.net> Alexandre Chapellon Ingénierie des systèmes open sources et réseaux. Follow me on twitter: @alxgomz <http://www.twitter.com/alxgomz>

3 4

Creating templates for users
by Krzysztof Grobelak 20 Oct '11

20 Oct '11

Hello, I am having some troubles creating templates with wimax attributes for users. I created files with atributes in them in the form: Alvarion-R3-IF-Name += CPEL3Mgmt, Alvarion-PDFID += 1, WiMAX-Packet-Data-Flow-Id += 1, WiMAX-Service-Data-Flow-Id += 1, WiMAX-Direction += 3, WiMAX-Transport-Type += 1, WiMAX-Uplink-QOS-Id += 1, WiMAX-Downlink-QOS-Id += 1, and then in the users file I use: 30001020 Cleartext-Password := "30001020" $INCLUDE cpe_mgmt, $INCLUDE ethcs_1_vlan_sf, WiMAX-VLAN-ID += 175, Session-Timeout = 3600, Reply-Message = "4motion test" but I am getting error: Thu Oct 20 16:35:24 2011 : Error: /usr/local/etc/raddb/users[63]: Parse error (reply) for entry 30001020: expecting operator Thu Oct 20 16:35:24 2011 : Error: Errors reading /usr/local/etc/raddb/users Thu Oct 20 16:35:24 2011 : Error: /usr/local/etc/raddb/modules/files[7]: Instantiation failed for module "files" Thu Oct 20 16:35:24 2011 : Error: /usr/local/etc/raddb/sites-enabled/default[152]: Failed to load module "files". Thu Oct 20 16:35:24 2011 : Error: /usr/local/etc/raddb/sites-enabled/default[62]: Errors parsing authorize section. Simillar thing happened when i tried using template.conf 30001020 Cleartext-Password := "30001020" $template cpe_mgmt, Session-Timeout = 3600, Reply-Message = "4motion test" but the error i got was: Thu Oct 20 17:00:46 2011 : Debug: including configuration file /usr/local/etc/raddb/templates.conf Thu Oct 20 17:00:46 2011 : Error: /usr/local/etc/raddb/templates.conf[109]: Invalid operator in assignment Thu Oct 20 17:00:46 2011 : Error: Errors reading /usr/local/etc/raddb/radiusd.conf Is the += format not supported in the templates.conf?? Or is there any other way to save myself the problem of typing all the attributes for each user?? Thanks in advance. Kind regards, Krzysztof

4 5

freeradius on FreeBSD
by Renata Dias 20 Oct '11

20 Oct '11

Hello, I'm new here ! This is my first post... I’m trying to install freeradius 2.1.12 on FreeBSD 7.4-STABLE, but I got the error: ===> freeradius-2.1.12 cannot install: unknown MySQL version: 54. *** Error code 1 Stop in /usr/ports/net/freeradius2. Can someone help-me? -- Renata Dias -- Renata Dias

4 4

Howto proxy (or not) based on client IP ?
by Fred 20 Oct '11

20 Oct '11

Hi all, Is there any way to select proxying or not based on client ip ? I would like to have * some nas authenticated locally (in fact via ldap) * some other nas proxyied to another radius. Does home_server parameter in clients.conf could help ? Best regards, Fred

2 3

Timestamp missing from accounting start
by Barry Botha 20 Oct '11

20 Oct '11

Hi List I've recently upgraded to Freeradius 2.1 from 1.9. I launch an exec script with: Exec bdns { wait = no program = " /dns-update.php %{User-Name} %{Acct-Status-Type} %{Framed-IP-Address} %{Timestamp}" input_pairs = request packet_type = Accounting-Request } Since the upgrade I've been getting this error: [bbar-dns] WARNING: Unknown module "Timestamp" in string expansion "%" When I inspect the Accounting-Request it has no Timestamp: rad_recv: Accounting-Request packet from host 196.1.1.1 port 1820, id=84, length=189 Acct-Session-Id = "7/0/0/1.188_08B45A01" Framed-Protocol = PPP Framed-IP-Address = 41.243.123.198 User-Name = "user@realm" X-Ascend-Connect-Progress = LAN-Session-Up Acct-Authentic = RADIUS Acct-Status-Type = Start NAS-Port-Type = Virtual NAS-Port = 1879113916 NAS-Port-Id = "7/0/0/1.188" Connect-Info = "AutoShapedVC" Calling-Station-Id = "0215522395" Class = 0x4e5331 Service-Type = Framed-User NAS-IP-Address = 196.1.2.1 X-Ascend-Session-Svr-Key = "7A2DA0BA" Acct-Delay-Time = 0 Vendor-1431-Attr-1 = 0x44534c Proxy-State = 0x323437 The NAS has not changed. Any ideas why I'm getting no {Timestamp} Thanks Barry

2 1

different python module settings for different virtual hosts
by Christoph Thielecke 20 Oct '11

20 Oct '11

Hello, I use the python module which works fine. Now I have to setup a second virtual host with different configuration of the python module. How I can tell freeradius to have one python module with setup a and one with setup b? Is it possible to import a module with new name? With best regards Christoph -- Linux User Group Wernigerode http://www.lug-wr.de/

2 1

rlm_perl not working
by Vincent, Fabien 20 Oct '11

20 Oct '11

Hi all, As you reply yesterday to my question, I have another one which is very embarrassing : I have the following packages installed on CentOS box : freeradius2.x86_64 freeradius2-mysql.x86_64 freeradius2-ldap.x86_64 freeradius2-perl.x86_64 freeradius2-utils.x86_64 I want to make some transformations on my accounting section but this doesn't work when I put the "perl" in accounting section. Radius stop working : /usr/sbin/radiusd -X conns: 0x25e9760 Module: Checking authorize {...} for more modules to load Module: Checking accounting {...} for more modules to load /etc/raddb/radiusd.conf[267]: Failed to find module "perl". /etc/raddb/radiusd.conf[263]: Errors parsing accounting section. I've found a lot of problems looking on my Google friend, but I didn't understand with a simple : accounting { # sql # comment perl } Using the simple configuration for modules found here: http://wiki.freeradius.org/Rlm_perl Does not work . Any ideas ? Thanks in advance for your help Regards, Fabien VINCENT

3 6

No connection after access-accept.
by Krzysztof Grobelak 20 Oct '11

20 Oct '11

Hello. I am trying to configure freeradius to work with Alvarion devices. It is working fine with Extreme but for some reason it does not work with 4motion. I installed the "master" version from git and I edited the dictionary files. My problem is that i see access-accept being sent but the connection is not established and radio keeps trying to authenticate with freeradius. Each attempt ends with access-accept being sent. Thanks in advance P.S. I am new to freeradius and wimax so please dont eat me alive... Regards, Krzysztof Debug: FreeRADIUS Version 3.0.0, for host i686-pc-linux-gnu, built on Oct 17 2011 at 10:26:54 Copyright (C) 1999-2009 The FreeRADIUS server project and contributors. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. You may redistribute copies of FreeRADIUS under the terms of the GNU General Public License v2. Compilation options: Regex flavour: Posix Starting - reading configuration files ... including configuration file /usr/local/etc/raddb/radiusd.conf including configuration file /usr/local/etc/raddb/proxy.conf including configuration file /usr/local/etc/raddb/clients.conf including files in directory /usr/local/etc/raddb/modules/ including configuration file /usr/local/etc/raddb/modules/redis including configuration file /usr/local/etc/raddb/modules/cui including configuration file /usr/local/etc/raddb/modules/echo including configuration file /usr/local/etc/raddb/modules/checkval including configuration file /usr/local/etc/raddb/modules/sql_log including configuration file /usr/local/etc/raddb/modules/smsotp including configuration file /usr/local/etc/raddb/modules/acct_unique including configuration file /usr/local/etc/raddb/modules/policy including configuration file /usr/local/etc/raddb/modules/realm including configuration file /usr/local/etc/raddb/modules/files including configuration file /usr/local/etc/raddb/modules/etc_group including configuration file /usr/local/etc/raddb/modules/ippool including configuration file /usr/local/etc/raddb/modules/inner-eap including configuration file /usr/local/etc/raddb/modules/pam including configuration file /usr/local/etc/raddb/modules/sql including configuration file /usr/local/etc/raddb/sql/mysql/dialup.conf including configuration file /usr/local/etc/raddb/modules/counter including configuration file /usr/local/etc/raddb/modules/expiration including configuration file /usr/local/etc/raddb/modules/detail.log including configuration file /usr/local/etc/raddb/modules/expr including configuration file /usr/local/etc/raddb/modules/ntlm_auth including configuration file /usr/local/etc/raddb/modules/mac2vlan including configuration file /usr/local/etc/raddb/modules/detail.example.com including configuration file /usr/local/etc/raddb/modules/always including configuration file /usr/local/etc/raddb/modules/logintime including configuration file /usr/local/etc/raddb/modules/replicate including configuration file /usr/local/etc/raddb/modules/unix including configuration file /usr/local/etc/raddb/modules/chap including configuration file /usr/local/etc/raddb/modules/linelog including configuration file /usr/local/etc/raddb/modules/radutmp including configuration file /usr/local/etc/raddb/modules/digest including configuration file /usr/local/etc/raddb/modules/sradutmp including configuration file /usr/local/etc/raddb/modules/preprocess including configuration file /usr/local/etc/raddb/modules/ldap including configuration file /usr/local/etc/raddb/modules/sqlippool including configuration file /usr/local/etc/raddb/sql/postgresql/ippool.conf including configuration file /usr/local/etc/raddb/modules/opendirectory including configuration file /usr/local/etc/raddb/modules/otp including configuration file /usr/local/etc/raddb/modules/rediswho including configuration file /usr/local/etc/raddb/modules/mschap including configuration file /usr/local/etc/raddb/modules/eap including configuration file /usr/local/etc/raddb/modules/attr_rewrite including configuration file /usr/local/etc/raddb/modules/exec including configuration file /usr/local/etc/raddb/modules/pap including configuration file /usr/local/etc/raddb/modules/sqlcounter_expire_on_login including configuration file /usr/local/etc/raddb/modules/mac2ip including configuration file /usr/local/etc/raddb/modules/utf8 including configuration file /usr/local/etc/raddb/modules/passwd including configuration file /usr/local/etc/raddb/modules/attr_filter including configuration file /usr/local/etc/raddb/modules/soh including configuration file /usr/local/etc/raddb/modules/detail including configuration file /usr/local/etc/raddb/modules/smbpasswd including configuration file /usr/local/etc/raddb/modules/dynamic_clients including configuration file /usr/local/etc/raddb/modules/wimax including configuration file /usr/local/etc/raddb/modules/krb5 including configuration file /usr/local/etc/raddb/modules/perl including configuration file /usr/local/etc/raddb/policy.conf including files in directory /usr/local/etc/raddb/sites-enabled/ including configuration file /usr/local/etc/raddb/sites-enabled/default including configuration file /usr/local/etc/raddb/sites-enabled/inner-tunnel including configuration file /usr/local/etc/raddb/sites-enabled/control-socket main { security { allow_core_dumps = no } } including dictionary file /usr/local/etc/raddb/dictionary main { name = "radiusd" prefix = "/usr/local" localstatedir = "/usr/local/var" sbindir = "/usr/local/sbin" logdir = "/usr/local/var/log/radius" run_dir = "/usr/local/var/run/radiusd" libdir = "/usr/local/lib" radacctdir = "/usr/local/var/log/radius/radacct" hostname_lookups = no max_request_time = 30 cleanup_delay = 5 max_requests = 1024 pidfile = "/usr/local/var/run/radiusd/radiusd.pid" checkrad = "/usr/local/sbin/checkrad" debug_level = 0 proxy_requests = yes log { stripped_names = no auth = no auth_badpass = no auth_goodpass = no } security { max_attributes = 200 reject_delay = 1 status_server = yes } } radiusd: #### Loading Realms and Home Servers #### proxy server { retry_delay = 5 retry_count = 3 default_fallback = no dead_time = 120 wake_all_if_all_dead = no } home_server localhost { ipaddr = 127.0.0.1 port = 1812 type = "auth" secret = "testing123" response_window = 20 max_outstanding = 65536 require_message_authenticator = yes zombie_period = 40 status_check = "status-server" ping_interval = 30 check_interval = 30 num_answers_to_alive = 3 num_pings_to_alive = 3 revive_interval = 120 status_check_timeout = 4 coa { irt = 2 mrt = 16 mrc = 5 mrd = 30 } limit { max_connections = 16 max_requests = 0 lifetime = 0 idle_timeout = 0 } } home_server_pool my_auth_failover { type = fail-over home_server = localhost } realm example.com { auth_pool = my_auth_failover } realm LOCAL { } radiusd: #### Loading Clients #### client localhost { ipaddr = 127.0.0.1 require_message_authenticator = no secret = "testing123" nastype = "other" max_connections = 16 } client 10.190.0.2 { require_message_authenticator = no secret = "pass" shortname = "Testing" nastype = "other" max_connections = 16 } radiusd: #### Instantiating modules #### instantiate { Module: Linked to module rlm_exec Module: Instantiating module "exec" from file /usr/local/etc/raddb/modules/exec exec { wait = no input_pairs = "request" shell_escape = yes } Module: Linked to module rlm_expr Module: Instantiating module "expr" from file /usr/local/etc/raddb/modules/expr Module: Linked to module rlm_expiration Module: Instantiating module "expiration" from file /usr/local/etc/raddb/modules/expiration expiration { reply-message = "Password Has Expired " } Module: Linked to module rlm_logintime Module: Instantiating module "logintime" from file /usr/local/etc/raddb/modules/logintime logintime { reply-message = "You are calling outside your allowed timespan " minimum-timeout = 60 } } radiusd: #### Loading Virtual Servers #### server { # from file /usr/local/etc/raddb/radiusd.conf modules { Module: Checking authenticate {...} for more modules to load Module: Linked to module rlm_chap Module: Instantiating module "chap" from file /usr/local/etc/raddb/modules/chap Module: Linked to module rlm_mschap Module: Instantiating module "mschap" from file /usr/local/etc/raddb/modules/mschap mschap { use_mppe = yes require_encryption = no require_strong = no with_ntdomain_hack = no passchange { } allow_retry = yes } Module: Linked to module rlm_eap Module: Instantiating module "eap" from file /usr/local/etc/raddb/modules/eap eap { default_eap_type = "ttls" timer_expire = 60 ignore_unknown_eap_types = no cisco_accounting_username_bug = no max_sessions = 4096 } Module: Linked to sub-module rlm_eap_md5 Module: Instantiating eap-md5 Module: Linked to sub-module rlm_eap_leap Module: Instantiating eap-leap Module: Linked to sub-module rlm_eap_gtc Module: Instantiating eap-gtc gtc { challenge = "Password: " auth_type = "PAP" } Module: Linked to sub-module rlm_eap_tls Module: Instantiating eap-tls tls { rsa_key_exchange = no dh_key_exchange = yes rsa_key_length = 512 dh_key_length = 512 verify_depth = 0 CA_path = "/usr/local/etc/raddb/certs" pem_file_type = yes private_key_file = "/usr/local/etc/raddb/certs/server.pem" certificate_file = "/usr/local/etc/raddb/certs/server.pem" CA_file = "/usr/local/etc/raddb/certs/ca.pem" private_key_password = "whatever" dh_file = "/usr/local/etc/raddb/certs/dh" random_file = "/usr/local/etc/raddb/certs/random" fragment_size = 1024 include_length = yes check_crl = no cipher_list = "DEFAULT" make_cert_command = "/usr/local/etc/raddb/certs/bootstrap" ecdh_curve = "prime256v1" cache { enable = no lifetime = 24 max_entries = 255 } verify { } ocsp { enable = no override_cert_url = yes url = "http://127.0.0.1/ocsp/" } } Module: Linked to sub-module rlm_eap_ttls Module: Instantiating eap-ttls ttls { default_eap_type = "md5" copy_request_to_tunnel = yes use_tunneled_reply = yes virtual_server = "inner-tunnel" include_length = yes } Module: Linked to sub-module rlm_eap_peap Module: Instantiating eap-peap peap { default_eap_type = "mschapv2" copy_request_to_tunnel = no use_tunneled_reply = no proxy_tunneled_request_as_eap = yes virtual_server = "inner-tunnel" soh = no } Module: Linked to sub-module rlm_eap_mschapv2 Module: Instantiating eap-mschapv2 mschapv2 { with_ntdomain_hack = no send_error = no } Module: Checking authorize {...} for more modules to load Module: Linked to module rlm_preprocess Module: Instantiating module "preprocess" from file /usr/local/etc/raddb/modules/preprocess preprocess { huntgroups = "/usr/local/etc/raddb/huntgroups" hints = "/usr/local/etc/raddb/hints" with_ascend_hack = no ascend_channels_per_line = 23 with_ntdomain_hack = no with_specialix_jetstream_hack = no with_cisco_vsa_hack = no with_alvarion_vsa_hack = no } Module: Linked to module rlm_files Module: Instantiating module "files" from file /usr/local/etc/raddb/modules/files files { usersfile = "/usr/local/etc/raddb/users" acctusersfile = "/usr/local/etc/raddb/acct_users" preproxy_usersfile = "/usr/local/etc/raddb/preproxy_users" compat = "no" } Module: Checking preacct {...} for more modules to load Module: Loading virtual module acct_unique Module: Linked to module rlm_realm Module: Instantiating module "suffix" from file /usr/local/etc/raddb/modules/realm realm suffix { format = "suffix" delimiter = "@" ignore_default = no ignore_null = no } Module: Linked to module rlm_wimax Module: Instantiating module "wimax" from file /usr/local/etc/raddb/modules/wimax wimax { delete_mppe_keys = no } Module: Checking accounting {...} for more modules to load Module: Linked to module rlm_unix Module: Instantiating module "unix" from file /usr/local/etc/raddb/modules/unix unix { radwtmp = "/usr/local/var/log/radius/radwtmp" } Module: Linked to module rlm_radutmp Module: Instantiating module "radutmp" from file /usr/local/etc/raddb/modules/radutmp radutmp { filename = "/usr/local/var/log/radius/radutmp" username = "%{User-Name}" case_sensitive = yes check_with_nas = yes perm = 384 callerid = yes } Module: Linked to module rlm_attr_filter Module: Instantiating module "attr_filter.accounting_response" from file /usr/local/etc/raddb/modules/attr_filter attr_filter attr_filter.accounting_response { attrsfile = "/usr/local/etc/raddb/attrs.accounting_response" key = "%{User-Name}" relaxed = no } Module: Checking session {...} for more modules to load Module: Checking post-proxy {...} for more modules to load Module: Checking post-auth {...} for more modules to load Module: Instantiating module "attr_filter.access_reject" from file /usr/local/etc/raddb/modules/attr_filter attr_filter attr_filter.access_reject { attrsfile = "/usr/local/etc/raddb/attrs.access_reject" key = "%{User-Name}" relaxed = no } } # modules } # server server inner-tunnel { # from file /usr/local/etc/raddb/sites-enabled/inner-tunnel modules { Module: Checking authenticate {...} for more modules to load Module: Checking authorize {...} for more modules to load Module: Checking session {...} for more modules to load Module: Checking post-proxy {...} for more modules to load Module: Checking post-auth {...} for more modules to load } # modules } # server radiusd: #### Opening IP addresses and Ports #### listen { type = "auth" ipaddr = * port = 0 } listen { type = "acct" ipaddr = * port = 0 } listen { type = "control" listen { socket = "/usr/local/var/run/radiusd/radiusd.sock" } } listen { type = "auth" ipaddr = 127.0.0.1 port = 18120 } Listening on authentication address * port 1812 Listening on accounting address * port 1813 Listening on command file /usr/local/var/run/radiusd/radiusd.sock Listening on authentication address 127.0.0.1 port 18120 as server inner-tunnel Opening new proxy address * port 1814 Listening on proxy address * port 1814 Ready to process requests. rad_recv: Access-Request packet from host 10.190.0.2 port 1812, id=225, length=226 User-Name = "{sm=1}test(a)company.ie" EAP-Message = 0x0201002a017b736d3d317d6d61676e612e74616c6c616768742e746573744061697273706565642e6965 Message-Authenticator = 0xb0e4f53c239e82a5a9424643abac90c5 NAS-Identifier = "BTS105" NAS-IP-Address = 10.190.0.2 Calling-Station-Id = "00-26-82-D0-B6-F6" WiMAX-BS-Id = 0xffc6c8690100 NAS-Port-Type = Wireless-802.16 Framed-MTU = 2000 Service-Type = Framed-User WiMAX-GMT-Timezone-offset = 0 WiMAX-Release = "1.0" WiMAX-Accounting-Capabilities = IP-Session-Based WiMAX-Hotlining-Capabilities = Hotline-Profile-Id Attr-26.24757.1.7 = 0x0000028a (0) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default (0) group authorize { (0) - entering group authorize {...} (0) [preprocess] = ok (0) [chap] = noop (0) [mschap] = noop (0) eap : EAP packet type response id 1 length 42 (0) eap : EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize (0) [eap] = ok (0) Found Auth-Type = ? (0) # Executing group from file /usr/local/etc/raddb/sites-enabled/default (0) group authenticate { (0) - entering group authenticate {...} (0) eap : EAP Identity (0) eap : processing type tls (0) tls : Initiate (0) tls : Start returned 1 (0) [eap] = handled Sending Access-Challenge of id 225 to 10.190.0.2 port 1812 EAP-Message = 0x010200061520 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x4524932a452686bf0e6f9b30d966adf3 (0) Finished request 0. Waking up in 0.3 seconds. rad_recv: Access-Request packet from host 10.190.0.2 port 1812, id=226, length=290 User-Name = "{sm=1}test(a)company.ie" EAP-Message = 0x0202005815800000004e16030100490100004503014d6f0492446dcf37684a8ba3964276e6a0af14e11c0c66ba0bfe09bee47296d900001e00390038003500160013000a00330032002f0015001200090014001100080100 Message-Authenticator = 0x16b9a8766e5ca7d66bd4109f08badf56 NAS-Identifier = "BTS105" NAS-IP-Address = 10.190.0.2 Calling-Station-Id = "00-26-82-D0-B6-F6" WiMAX-BS-Id = 0xffc6c8690100 NAS-Port-Type = Wireless-802.16 Framed-MTU = 2000 Service-Type = Framed-User WiMAX-GMT-Timezone-offset = 0 WiMAX-Release = "1.0" WiMAX-Accounting-Capabilities = IP-Session-Based WiMAX-Hotlining-Capabilities = Hotline-Profile-Id Attr-26.24757.1.7 = 0x0000028a State = 0x4524932a452686bf0e6f9b30d966adf3 (1) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default (1) group authorize { (1) - entering group authorize {...} (1) [preprocess] = ok (1) [chap] = noop (1) [mschap] = noop (1) eap : EAP packet type response id 2 length 88 (1) eap : Continuing tunnel setup. (1) [eap] = ok (1) Found Auth-Type = ? (1) # Executing group from file /usr/local/etc/raddb/sites-enabled/default (1) group authenticate { (1) - entering group authenticate {...} (1) eap : Request found, released from the list (1) eap : EAP/ttls (1) eap : processing type ttls (1) ttls : Authenticate (1) ttls : processing EAP-TLS TLS Length 78 (1) ttls : Length Included (1) ttls : eaptls_verify returned 11 (1) ttls : (other): before/accept initialization (1) ttls : TLS_accept: before/accept initialization (1) ttls : <<< TLS 1.0 Handshake [length 0049], ClientHello (1) ttls : TLS_accept: SSLv3 read client hello A (1) ttls : >>> TLS 1.0 Handshake [length 002a], ServerHello (1) ttls : TLS_accept: SSLv3 write server hello A (1) ttls : >>> TLS 1.0 Handshake [length 085e], Certificate (1) ttls : TLS_accept: SSLv3 write certificate A (1) ttls : >>> TLS 1.0 Handshake [length 020d], ServerKeyExchange (1) ttls : TLS_accept: SSLv3 write key exchange A (1) ttls : >>> TLS 1.0 Handshake [length 0004], ServerHelloDone (1) ttls : TLS_accept: SSLv3 write server done A (1) ttls : TLS_accept: SSLv3 flush data (1) ttls : TLS_accept: Need to read more data: SSLv3 read client certificate A In SSL Handshake Phase In SSL Accept mode (1) ttls : eaptls_process returned 13 (1) [eap] = handled Sending Access-Challenge of id 226 to 10.190.0.2 port 1812 EAP-Message = 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 EAP-Message = 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 EAP-Message = 0xbb17624bb71f12a488110b381a1a629f04fe7811e5589b7cfebad4e16d89ce6b982880f28db5f6817bda4db85b83520a6d47f682e224f70e9a104fc421ca712b8fa4c1b9e6c98329a5db4150bb6d06fe29729e2842c5ecb6960b89cbdadc1ec91e7eadbdb4288023659fef46b02ec89bb47026e86c85aefb37d6df74167a3e12279d32b42199ba04013f8d4985c218365f0f60c3d9af227a3949125925db3ffb1bdccf34548f7626dac63e22b0624b6f16669d47fbc7ca4ddf2f794d004b901ecb090203010001a317301530130603551d25040c300a06082b06010505070301300d06092a864886f70d01010405000382010100b676c0afe25190b575 EAP-Message = 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 EAP-Message = 0xa73082038fa0030201020209 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x4524932a442786bf0e6f9b30d966adf3 (1) Finished request 1. Waking up in 0.1 seconds. rad_recv: Access-Request packet from host 10.190.0.2 port 1812, id=227, length=208 User-Name = "{sm=1}test(a)company.ie" EAP-Message = 0x020300061500 Message-Authenticator = 0x9a77a1ab1819f89e18fb8f7a8d263dbc NAS-Identifier = "BTS105" NAS-IP-Address = 10.190.0.2 Calling-Station-Id = "00-26-82-D0-B6-F6" WiMAX-BS-Id = 0xffc6c8690100 NAS-Port-Type = Wireless-802.16 Framed-MTU = 2000 Service-Type = Framed-User WiMAX-GMT-Timezone-offset = 0 WiMAX-Release = "1.0" WiMAX-Accounting-Capabilities = IP-Session-Based WiMAX-Hotlining-Capabilities = Hotline-Profile-Id Attr-26.24757.1.7 = 0x0000028a State = 0x4524932a442786bf0e6f9b30d966adf3 (2) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default (2) group authorize { (2) - entering group authorize {...} (2) [preprocess] = ok (2) [chap] = noop (2) [mschap] = noop (2) eap : EAP packet type response id 3 length 6 (2) eap : Continuing tunnel setup. (2) [eap] = ok (2) Found Auth-Type = ? (2) # Executing group from file /usr/local/etc/raddb/sites-enabled/default (2) group authenticate { (2) - entering group authenticate {...} (2) eap : Request found, released from the list (2) eap : EAP/ttls (2) eap : processing type ttls (2) ttls : Authenticate (2) ttls : processing EAP-TLS (2) ttls : Received TLS ACK (2) ttls : Received TLS ACK (2) ttls : ACK handshake fragment handler (2) ttls : eaptls_verify returned 1 (2) ttls : eaptls_process returned 13 (2) [eap] = handled Sending Access-Challenge of id 227 to 10.190.0.2 port 1812 EAP-Message = 0x0104040015c000000aad00ec1d720e4a7e8a98300d06092a864886f70d0101050500308193310b3009060355040613024652310f300d060355040813065261646975733112301006035504071309536f6d65776865726531153013060355040a130c4578616d706c6520496e632e3120301e06092a864886f70d010901161161646d696e406578616d706c652e636f6d312630240603550403131d4578616d706c6520436572746966696361746520417574686f72697479301e170d3131313031333039353734375a170d3132313031323039353734375a308193310b3009060355040613024652310f300d0603550408130652616469757331123010 EAP-Message = 0x06035504071309536f6d65776865726531153013060355040a130c4578616d706c6520496e632e3120301e06092a864886f70d010901161161646d696e406578616d706c652e636f6d312630240603550403131d4578616d706c6520436572746966696361746520417574686f7269747930820122300d06092a864886f70d01010105000382010f003082010a0282010100be734cc62ecb7177f45d9f49d0dc7c67f1e8f71f9ad048dd67a12de738c98729d524e687e47b801bf912a3ce76ff5c35cbbae16eed0733b5e51b53633123803af7f8bdb2a456b82f3c022ab8aa75e09e55f898044a1de747799af4506d191327f3cb2fd28c87d277828b1b EAP-Message = 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 EAP-Message = 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 EAP-Message = 0x29f6a43153b63396708d1c2a Message-Authenticator = 0x00000000000000000000000000000000 State = 0x4524932a472086bf0e6f9b30d966adf3 (2) Finished request 2. rad_recv: Access-Request packet from host 10.190.0.2 port 1812, id=228, length=208 User-Name = "{sm=1}test(a)company.ie" EAP-Message = 0x020400061500 Message-Authenticator = 0xe3f7dbd13796664921230156fd4a7f0b NAS-Identifier = "BTS105" NAS-IP-Address = 10.190.0.2 Calling-Station-Id = "00-26-82-D0-B6-F6" WiMAX-BS-Id = 0xffc6c8690100 NAS-Port-Type = Wireless-802.16 Framed-MTU = 2000 Service-Type = Framed-User WiMAX-GMT-Timezone-offset = 0 WiMAX-Release = "1.0" WiMAX-Accounting-Capabilities = IP-Session-Based WiMAX-Hotlining-Capabilities = Hotline-Profile-Id Attr-26.24757.1.7 = 0x0000028a State = 0x4524932a472086bf0e6f9b30d966adf3 (3) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default (3) group authorize { (3) - entering group authorize {...} (3) [preprocess] = ok (3) [chap] = noop (3) [mschap] = noop (3) eap : EAP packet type response id 4 length 6 (3) eap : Continuing tunnel setup. (3) [eap] = ok (3) Found Auth-Type = ? (3) # Executing group from file /usr/local/etc/raddb/sites-enabled/default (3) group authenticate { (3) - entering group authenticate {...} (3) eap : Request found, released from the list (3) eap : EAP/ttls (3) eap : processing type ttls (3) ttls : Authenticate (3) ttls : processing EAP-TLS (3) ttls : Received TLS ACK (3) ttls : Received TLS ACK (3) ttls : ACK handshake fragment handler (3) ttls : eaptls_verify returned 1 (3) ttls : eaptls_process returned 13 (3) [eap] = handled Sending Access-Challenge of id 228 to 10.190.0.2 port 1812 EAP-Message = 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 EAP-Message = 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 EAP-Message = 0xb71e3de49e55f6775effac0d28046d1510714dbd68c4d55dedb7329f9ba3de55154a4ffd8d2aad7081dc07b232ff609ca8c19743ba19ccd2d1b3bf35dd1ccd78c1d54f477a4336188fb9298426a941501972562ed1fca0efad8c451b0ec15674ff86500e67617241c95625ddecc82feefc41c0eb91cdab0cc56176884e28aab3c850a81bd7736e1ec133d6b83db28db10623c552c5f7a2d7a6d59e0f1cf362b155e415a274088d2eb875d07acd63236660e40f200f6055bd2c0c934777c61d55c1a57d7983d867c016030100040e000000 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x4524932a462186bf0e6f9b30d966adf3 (3) Finished request 3. Waking up in 0.2 seconds. Waking up in 4.3 seconds. rad_recv: Access-Request packet from host 10.190.0.2 port 1812, id=229, length=410 User-Name = "{sm=1}test(a)company.ie" EAP-Message = 0x020500d01580000000c61603010086100000820080e3190ec3957550a29a5f545907823a1eadcd83d25d26b74f1858aae52bac948aef1e3d75bc2adff031a57ad656d2d09066f0cae0630e0c66d0487abc980cb7d6631a6531f05cba19b4a94f628a6bda9a90aae7e58f33fe204399f1fcd215d007dba697579f7bcb002baa5d67c06a10d82953c53a31b100711f4f0d07e550a3d414030100010116030100308a7e900fbfb4f5de1ef3c91092938dee297c5a4b41f537309996762989cffc3aa2475130e85a6cfcbd3cc5d4f4a38b01 Message-Authenticator = 0x4f4cb9ffdb83cca6564a6d11de9eca5e NAS-Identifier = "BTS105" NAS-IP-Address = 10.190.0.2 Calling-Station-Id = "00-26-82-D0-B6-F6" WiMAX-BS-Id = 0xffc6c8690100 NAS-Port-Type = Wireless-802.16 Framed-MTU = 2000 Service-Type = Framed-User WiMAX-GMT-Timezone-offset = 0 WiMAX-Release = "1.0" WiMAX-Accounting-Capabilities = IP-Session-Based WiMAX-Hotlining-Capabilities = Hotline-Profile-Id Attr-26.24757.1.7 = 0x0000028a State = 0x4524932a462186bf0e6f9b30d966adf3 (4) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default (4) group authorize { (4) - entering group authorize {...} (4) [preprocess] = ok (4) [chap] = noop (4) [mschap] = noop (4) eap : EAP packet type response id 5 length 208 (4) eap : Continuing tunnel setup. (4) [eap] = ok (4) Found Auth-Type = ? (4) # Executing group from file /usr/local/etc/raddb/sites-enabled/default (4) group authenticate { (4) - entering group authenticate {...} (4) eap : Request found, released from the list (4) eap : EAP/ttls (4) eap : processing type ttls (4) ttls : Authenticate (4) ttls : processing EAP-TLS TLS Length 198 (4) ttls : Length Included (4) ttls : eaptls_verify returned 11 (4) ttls : <<< TLS 1.0 Handshake [length 0086], ClientKeyExchange (4) ttls : TLS_accept: SSLv3 read client key exchange A (4) ttls : <<< TLS 1.0 ChangeCipherSpec [length 0001] (4) ttls : <<< TLS 1.0 Handshake [length 0010], Finished (4) ttls : TLS_accept: SSLv3 read finished A (4) ttls : >>> TLS 1.0 ChangeCipherSpec [length 0001] (4) ttls : TLS_accept: SSLv3 write change cipher spec A (4) ttls : >>> TLS 1.0 Handshake [length 0010], Finished (4) ttls : TLS_accept: SSLv3 write finished A (4) ttls : TLS_accept: SSLv3 flush data (4) ttls : (other): SSL negotiation finished successfully SSL Connection Established (4) ttls : eaptls_process returned 13 (4) [eap] = handled Sending Access-Challenge of id 229 to 10.190.0.2 port 1812 EAP-Message = 0x0106004515800000003b14030100010116030100303a882b92af53c50ce085959593e73fca32ab9a7bd2e2e0a895c165c0a4163a638e8f12fef6f0bc8878a70cfcda0548a8 Message-Authenticator = 0x00000000000000000000000000000000 State = 0x4524932a412286bf0e6f9b30d966adf3 (4) Finished request 4. Waking up in 0.2 seconds. rad_recv: Access-Request packet from host 10.190.0.2 port 1812, id=230, length=378 User-Name = "{sm=1test(a)company.ie" EAP-Message = 0x020600b0150017030100201783b2821501d183457ee81425c3bcbfd372c1207cc52b44e4af3250a771e4181703010080a65edf5e1fddb09f70ebffef22b5811ebb4d7f3143b2d1ecf88e2af29edd0178dc38aa45de3e8ac0106fa7259392dbb721ed242bf6fd1a79cdc10faad024b583e8710f2396246d34353b915f3a49771b11ed93e106564b0f94f208631a4f9852c21452c53492d5302b2571ec8f1b95d0b1abdaf202da0f42b9b68c863653886c Message-Authenticator = 0x064bdfc96ada80a4ac9a92242232b9ae NAS-Identifier = "BTS105" NAS-IP-Address = 10.190.0.2 Calling-Station-Id = "00-26-82-D0-B6-F6" WiMAX-BS-Id = 0xffc6c8690100 NAS-Port-Type = Wireless-802.16 Framed-MTU = 2000 Service-Type = Framed-User WiMAX-GMT-Timezone-offset = 0 WiMAX-Release = "1.0" WiMAX-Accounting-Capabilities = IP-Session-Based WiMAX-Hotlining-Capabilities = Hotline-Profile-Id Attr-26.24757.1.7 = 0x0000028a State = 0x4524932a412286bf0e6f9b30d966adf3 (5) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default (5) group authorize { (5) - entering group authorize {...} (5) [preprocess] = ok (5) [chap] = noop (5) [mschap] = noop (5) eap : EAP packet type response id 6 length 176 (5) eap : Continuing tunnel setup. (5) [eap] = ok (5) Found Auth-Type = ? (5) # Executing group from file /usr/local/etc/raddb/sites-enabled/default (5) group authenticate { (5) - entering group authenticate {...} (5) eap : Request found, released from the list (5) eap : EAP/ttls (5) eap : processing type ttls (5) ttls : Authenticate (5) ttls : processing EAP-TLS (5) ttls : eaptls_verify returned 7 (5) ttls : Done initial handshake (5) ttls : eaptls_process returned 7 (5) ttls : Session established. Proceeding to decode tunneled attributes. (5) ttls : Got tunneled request User-Name = "30001020" MS-CHAP-Challenge = 0x967d3f6435e31b63 MS-CHAP-Response = 0xb801000000000000000000000000000000000000000000000000b32723b5ce6e52ba066370add032fa03fecc6350d759fa7f FreeRADIUS-Proxied-To = 127.0.0.1 (5) ttls : Sending tunneled request User-Name = "30001020" MS-CHAP-Challenge = 0x967d3f6435e31b63 MS-CHAP-Response = 0xb801000000000000000000000000000000000000000000000000b32723b5ce6e52ba066370add032fa03fecc6350d759fa7f FreeRADIUS-Proxied-To = 127.0.0.1 NAS-Identifier = "BTS105" NAS-IP-Address = 10.190.0.2 Calling-Station-Id = "00-26-82-D0-B6-F6" WiMAX-BS-Id = 0xffc6c8690100 NAS-Port-Type = Wireless-802.16 Framed-MTU = 2000 Service-Type = Framed-User WiMAX-Release = "1.0" WiMAX-Accounting-Capabilities = IP-Session-Based WiMAX-Hotlining-Capabilities = Hotline-Profile-Id Attr-26.24757.1.7 = 0x0000028a server inner-tunnel { (5) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/inner-tunnel (5) group authorize { (5) - entering group authorize {...} (5) [chap] = noop (5) mschap : Found MS-CHAP attributes. Setting 'Auth-Type = mschap' (5) [mschap] = ok (5) eap : No EAP-Message, not doing EAP (5) [eap] = noop (5) files : users: Matched entry 30001020 at line 99 (5) [files] = ok (5) [preprocess] = ok (5) Found Auth-Type = ? (5) # Executing group from file /usr/local/etc/raddb/sites-enabled/inner-tunnel (5) group MS-CHAP { (5) - entering group MS-CHAP {...} (5) mschap : Told to do MS-CHAPv1 with NT-Password (5) mschap : adding MS-CHAPv1 MPPE keys (5) [mschap] = ok (5) # Executing section post-auth from file /usr/local/etc/raddb/sites-enabled/inner-tunnel (5) group post-auth { (5) - entering group post-auth {...} (5) update outer.reply { (5) expand: %{request:User-Name} -> 30001020 (5) } # update outer.reply = noop (5) wimax : No EAP-MSK or EAP-EMSK. Cannot create WiMAX keys. (5) [wimax] = noop } # server inner-tunnel (5) ttls : Got tunneled reply code 2 Alvarion-R3-IF-Name += "CPEL3Mgmt" Alvarion-PDFID += 1 WiMAX-Packet-Data-Flow-Id += 1 WiMAX-Direction += Bi-Directional WiMAX-Transport-Type += IPv4-CS WiMAX-Uplink-QOS-Id += 1 WiMAX-Downlink-QOS-Id += 1 WiMAX-ClassifierID += 2 WiMAX-Classifier-Priority += 1 WiMAX-Classifier-Direction += IN WiMAX-IP-TOS-DSCP-Range-and-Mask += 0x31353739323633 WiMAX-ClassifierID += 1 WiMAX-Classifier-Priority += 1 WiMAX-Classifier-Direction += OUT WiMAX-IP-TOS-DSCP-Range-and-Mask += 0x3635353335 WiMAX-QoS-Id += 1 WiMAX-Schedule-Type += Best-Effort WiMAX-Traffic-Priority += 4 WiMAX-Maximum-Sustained-Traffic-Rate += 512000 WiMAX-IP-Technology += PMIP4 Alvarion-R3-IF-Name += "HazelL2Service" Alvarion-PDFID += 2 WiMAX-Packet-Data-Flow-Id += 2 WiMAX-Direction += Bi-Directional WiMAX-Transport-Type += Ethernet WiMAX-Uplink-QOS-Id += 2 WiMAX-Downlink-QOS-Id += 2 WiMAX-ClassifierID += 1 WiMAX-Classifier-Priority += 1 WiMAX-Classifier-Direction += Bi-Directional WiMAX-VLAN-ID += 175 WiMAX-QoS-Id += 2 WiMAX-Schedule-Type += nrtPS WiMAX-Traffic-Priority += 1 WiMAX-Maximum-Sustained-Traffic-Rate += 4096000 WiMAX-Minimum-Reserved-Traffic-Rate += 1024000 WiMAX-IP-Technology += Ethernet-CS WiMAX-hHA-IP-MIP4 += 12.12.12.12 Session-Timeout = 3600 Reply-Message = "4motion test" MS-CHAP-MPPE-Keys = 0x250838025ed089c5740e1ec19c1d0bedd9776bd85e9fca880000000000000000 MS-MPPE-Encryption-Policy = Encryption-Allowed MS-MPPE-Encryption-Types = RC4-40or128-bit-Allowed (5) ttls : Got tunneled Access-Accept (5) eap : Freeing handler (5) [eap] = ok (5) # Executing section post-auth from file /usr/local/etc/raddb/sites-enabled/default (5) group post-auth { (5) - entering group post-auth {...} (5) update request { (5) expand: %{User-Name} -> {sm=1}test(a)company.ie (5) } # update request = noop (5) update reply { (5) expand: %{reply:EAP-MSK} -> 0x1fb12ddd1fa37055e2178c1525d32d189d720d0987006686a6a5306992df472e3c1a0fade59132dd591aed447610e20c90a230fa5e7e345461261f8893588691 (5) } # update reply = noop (5) wimax : MIP-RK = 0x34cb0114be346973d5832ba7410516ed882d1fb1fb0ae3ad608e687c48b01ab6948fd63668f8d0e5fbdb1c3169e676b44aea80064919ae759cc997505584dbf7 (5) wimax : MIP-SPI = dd1974b7 (5) [wimax] = updated Sending Access-Accept of id 230 to 10.190.0.2 port 1812 User-Name = "30001020" Alvarion-R3-IF-Name = "CPEL3Mgmt" Alvarion-PDFID = 1 WiMAX-Packet-Data-Flow-Id = 1 WiMAX-Direction = Bi-Directional WiMAX-Transport-Type = IPv4-CS WiMAX-Uplink-QOS-Id = 1 WiMAX-Downlink-QOS-Id = 1 WiMAX-ClassifierID = 2 WiMAX-Classifier-Priority = 1 WiMAX-Classifier-Direction = IN WiMAX-IP-TOS-DSCP-Range-and-Mask = 0x31353739323633 WiMAX-ClassifierID = 1 WiMAX-Classifier-Priority = 1 WiMAX-Classifier-Direction = OUT WiMAX-IP-TOS-DSCP-Range-and-Mask = 0x3635353335 WiMAX-QoS-Id = 1 WiMAX-Schedule-Type = Best-Effort WiMAX-Traffic-Priority = 4 WiMAX-Maximum-Sustained-Traffic-Rate = 512000 WiMAX-IP-Technology = Ethernet-CS Alvarion-R3-IF-Name = "HazelL2Service" Alvarion-PDFID = 2 WiMAX-Packet-Data-Flow-Id = 2 WiMAX-Direction = Bi-Directional WiMAX-Transport-Type = Ethernet WiMAX-Uplink-QOS-Id = 2 WiMAX-Downlink-QOS-Id = 2 WiMAX-ClassifierID = 1 WiMAX-Classifier-Priority = 1 WiMAX-Classifier-Direction = Bi-Directional WiMAX-VLAN-ID = 175 WiMAX-QoS-Id = 2 WiMAX-Schedule-Type = nrtPS WiMAX-Traffic-Priority = 1 WiMAX-Maximum-Sustained-Traffic-Rate = 4096000 WiMAX-Minimum-Reserved-Traffic-Rate = 1024000 WiMAX-IP-Technology = Ethernet-CS WiMAX-hHA-IP-MIP4 = 12.12.12.12 Session-Timeout = 3600 Reply-Message = "4motion test" MS-CHAP-MPPE-Keys = 0x250838025ed089c5740e1ec19c1d0bedd9776bd85e9fca880000000000000000 MS-MPPE-Encryption-Policy = Encryption-Allowed MS-MPPE-Encryption-Types = RC4-40or128-bit-Allowed MS-MPPE-Recv-Key = 0x1fb12ddd1fa37055e2178c1525d32d189d720d0987006686a6a5306992df472e MS-MPPE-Send-Key = 0x3c1a0fade59132dd591aed447610e20c90a230fa5e7e345461261f8893588691 EAP-Message = 0x03060004 Message-Authenticator = 0x00000000000000000000000000000000 WiMAX-MSK = 0x1fb12ddd1fa37055e2178c1525d32d189d720d0987006686a6a5306992df472e3c1a0fade59132dd591aed447610e20c90a230fa5e7e345461261f8893588691 (5) Finished request 5. Waking up in 0.1 seconds. Waking up in 0.1 seconds. Waking up in 2.9 seconds. (0) Cleaning up request packet ID 225 with timestamp +85 Waking up in 0.1 seconds. (1) Cleaning up request packet ID 226 with timestamp +85 (2) Cleaning up request packet ID 227 with timestamp +85 (3) Cleaning up request packet ID 228 with timestamp +85 Waking up in 1.2 seconds. (4) Cleaning up request packet ID 229 with timestamp +86 Waking up in 0.1 seconds. (5) Cleaning up request packet ID 230 with timestamp +86 Ready to process requests. rad_recv: Access-Request packet from host 10.190.0.2 port 1812, id=231, length=226 User-Name = "{sm=1}test(a)company.ie" EAP-Message = 0x0201002a017b736d3d317d6d61676e612e74616c6c616768742e746573744061697273706565642e6965 Message-Authenticator = 0x2304870d06de86fa88b3ccd2de56a789 NAS-Identifier = "BTS105" NAS-IP-Address = 10.190.0.2 Calling-Station-Id = "00-26-82-D0-B6-F6" WiMAX-BS-Id = 0xffc6c8690100 NAS-Port-Type = Wireless-802.16 Framed-MTU = 2000 Service-Type = Framed-User WiMAX-GMT-Timezone-offset = 0 WiMAX-Release = "1.0" WiMAX-Accounting-Capabilities = IP-Session-Based WiMAX-Hotlining-Capabilities = Hotline-Profile-Id Attr-26.24757.1.7 = 0x0000028a (6) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default (6) group authorize { (6) - entering group authorize {...} (6) [preprocess] = ok (6) [chap] = noop (6) [mschap] = noop (6) eap : EAP packet type response id 1 length 42 (6) eap : EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize (6) [eap] = ok (6) Found Auth-Type = ? (6) # Executing group from file /usr/local/etc/raddb/sites-enabled/default (6) group authenticate { (6) - entering group authenticate {...} (6) eap : EAP Identity (6) eap : processing type tls (6) tls : Initiate (6) tls : Start returned 1 (6) [eap] = handled Sending Access-Challenge of id 231 to 10.190.0.2 port 1812 EAP-Message = 0x010200061520 Message-Authenticator = 0x00000000000000000000000000000000 State = 0xfdcbcc4afdc9d9fe908aaa2f4bb4f780 (6) Finished request 6. Waking up in 0.3 seconds. rad_recv: Access-Request packet from host 10.190.0.2 port 1812, id=232, length=290 User-Name = "{sm=1}test(a)company.ie" EAP-Message = 0x0202005815800000004e16030100490100004503014d6f049b50d6ea950c49e9ddac3c33c4a0477aefbe9119045fd3313c4148aa9300001e00390038003500160013000a00330032002f0015001200090014001100080100 Message-Authenticator = 0xab2efdd42f1f345c5b0ff3654e5fbeb1 NAS-Identifier = "BTS105" NAS-IP-Address = 10.190.0.2 Calling-Station-Id = "00-26-82-D0-B6-F6" WiMAX-BS-Id = 0xffc6c8690100 NAS-Port-Type = Wireless-802.16 Framed-MTU = 2000 Service-Type = Framed-User WiMAX-GMT-Timezone-offset = 0 WiMAX-Release = "1.0" WiMAX-Accounting-Capabilities = IP-Session-Based WiMAX-Hotlining-Capabilities = Hotline-Profile-Id Attr-26.24757.1.7 = 0x0000028a State = 0xfdcbcc4afdc9d9fe908aaa2f4bb4f780 (7) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default (7) group authorize { (7) - entering group authorize {...} (7) [preprocess] = ok (7) [chap] = noop (7) [mschap] = noop (7) eap : EAP packet type response id 2 length 88 (7) eap : Continuing tunnel setup. (7) [eap] = ok (7) Found Auth-Type = ? (7) # Executing group from file /usr/local/etc/raddb/sites-enabled/default (7) group authenticate { (7) - entering group authenticate {...} (7) eap : Request found, released from the list (7) eap : EAP/ttls (7) eap : processing type ttls (7) ttls : Authenticate (7) ttls : processing EAP-TLS TLS Length 78 (7) ttls : Length Included (7) ttls : eaptls_verify returned 11 (7) ttls : (other): before/accept initialization (7) ttls : TLS_accept: before/accept initialization (7) ttls : <<< TLS 1.0 Handshake [length 0049], ClientHello (7) ttls : TLS_accept: SSLv3 read client hello A (7) ttls : >>> TLS 1.0 Handshake [length 002a], ServerHello (7) ttls : TLS_accept: SSLv3 write server hello A (7) ttls : >>> TLS 1.0 Handshake [length 085e], Certificate (7) ttls : TLS_accept: SSLv3 write certificate A (7) ttls : >>> TLS 1.0 Handshake [length 020d], ServerKeyExchange (7) ttls : TLS_accept: SSLv3 write key exchange A (7) ttls : >>> TLS 1.0 Handshake [length 0004], ServerHelloDone (7) ttls : TLS_accept: SSLv3 write server done A (7) ttls : TLS_accept: SSLv3 flush data (7) ttls : TLS_accept: Need to read more data: SSLv3 read client certificate A In SSL Handshake Phase In SSL Accept mode (7) ttls : eaptls_process returned 13 (7) [eap] = handled Sending Access-Challenge of id 232 to 10.190.0.2 port 1812 EAP-Message = 0x0103040015c000000aad160301002a0200002603014e9ee512e286821d40c5caafa8f5cd1b8a1ed466ce0608d778ac01ab923d418c00003900160301085e0b00085a0008570003a6308203a23082028aa003020102020101300d06092a864886f70d0101040500308193310b3009060355040613024652310f300d060355040813065261646975733112301006035504071309536f6d65776865726531153013060355040a130c4578616d706c6520496e632e3120301e06092a864886f70d010901161161646d696e406578616d706c652e636f6d312630240603550403131d4578616d706c6520436572746966696361746520417574686f72697479 EAP-Message = 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 EAP-Message = 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 EAP-Message = 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 EAP-Message = 0xa73082038fa0030201020209 Message-Authenticator = 0x00000000000000000000000000000000 State = 0xfdcbcc4afcc8d9fe908aaa2f4bb4f780 (7) Finished request 7. Waking up in 0.1 seconds. rad_recv: Access-Request packet from host 10.190.0.2 port 1812, id=233, length=208 User-Name = "{sm=1}test(a)company.ie" EAP-Message = 0x020300061500 Message-Authenticator = 0xe4548d83804e1e53f53cce5d4e69eede NAS-Identifier = "BTS105" NAS-IP-Address = 10.190.0.2 Calling-Station-Id = "00-26-82-D0-B6-F6" WiMAX-BS-Id = 0xffc6c8690100 NAS-Port-Type = Wireless-802.16 Framed-MTU = 2000 Service-Type = Framed-User WiMAX-GMT-Timezone-offset = 0 WiMAX-Release = "1.0" WiMAX-Accounting-Capabilities = IP-Session-Based WiMAX-Hotlining-Capabilities = Hotline-Profile-Id Attr-26.24757.1.7 = 0x0000028a State = 0xfdcbcc4afcc8d9fe908aaa2f4bb4f780 (8) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default (8) group authorize { (8) - entering group authorize {...} (8) [preprocess] = ok (8) [chap] = noop (8) [mschap] = noop (8) eap : EAP packet type response id 3 length 6 (8) eap : Continuing tunnel setup. (8) [eap] = ok (8) Found Auth-Type = ? (8) # Executing group from file /usr/local/etc/raddb/sites-enabled/default (8) group authenticate { (8) - entering group authenticate {...} (8) eap : Request found, released from the list (8) eap : EAP/ttls (8) eap : processing type ttls (8) ttls : Authenticate (8) ttls : processing EAP-TLS (8) ttls : Received TLS ACK (8) ttls : Received TLS ACK (8) ttls : ACK handshake fragment handler (8) ttls : eaptls_verify returned 1 (8) ttls : eaptls_process returned 13 (8) [eap] = handled Sending Access-Challenge of id 233 to 10.190.0.2 port 1812 EAP-Message = 0x0104040015c000000aad00ec1d720e4a7e8a98300d06092a864886f70d0101050500308193310b3009060355040613024652310f300d060355040813065261646975733112301006035504071309536f6d65776865726531153013060355040a130c4578616d706c6520496e632e3120301e06092a864886f70d010901161161646d696e406578616d706c652e636f6d312630240603550403131d4578616d706c6520436572746966696361746520417574686f72697479301e170d3131313031333039353734375a170d3132313031323039353734375a308193310b3009060355040613024652310f300d0603550408130652616469757331123010 EAP-Message = 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 EAP-Message = 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 EAP-Message = 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 EAP-Message = 0x29f6a43153b63396708d1c2a Message-Authenticator = 0x00000000000000000000000000000000 State = 0xfdcbcc4affcfd9fe908aaa2f4bb4f780 (8) Finished request 8.

3 5