- Freeradius-Users - lists.freeradius.org

NAS administration
by 3＠D4rkn3ss DuMb 30 Jan '17

30 Jan '17

Dear List, I have a working setup of 5 FreeRadius servers for my WIFI users. Since the NAS number is increasing in monthly basis, I am wondering what is the best practice (security) when it comes NAS user authentication: - would it be better to have a separate server for the NAS user (cisco users) authentication ? or could I have both the WiFi user auth and NAS user auth on the same server? - The WiFi auth is based on MSCHAP module (against the AD), and since MSCHAP is not possible with the NAS user authentication, I assume that I have to use NTLM with PAP to authenticate the NAS user to the AD; These setup can't be on the same server (at least binding on same ports). Am I correct? or do I have it wrong? Thank you, Regards

1 0

MS-CHAP modules
by Chris Howley 30 Jan '17

30 Jan '17

Hi, Thank you for your advice on the use of multiple MSCHAP modules. I made the changes that were suggested but I'm still unable to authenticate users in different realms. Thanks Chris In the authorize section of inner-tunnel server. # If the users are logging in with an MS-CHAP-Challenge # attribute for authentication, the mschap module will find # the MS-CHAP-Challenge attribute, and add 'Auth-Type := MS-CHAP' # to the request, which will cause the server to then use # the mschap module for authentication. mschap I have defined two mschap modules (mschap_ds and mschap_admin) and made the following changes in the inner-tunnel authenticate section. # # MSCHAP authentication. Auth-Type MS-CHAP { if ("%{outer.request:User-Name}" =~ /@realm$/i){ mschap-ds { ok = return } } else { mschap-admin { ok = return } } } # # For old names, too. #mschap < -- I commented out this entry The authentication of a user in either realm failed with the following error message. (9) # Executing group from file /etc/raddb/sites-enabled/inner-tunnel (9) authenticate { (9) eap: Expiring EAP session with state 0x93ae5ad093a740b0 (9) eap: Finished EAP session with state 0x93ae5ad093a740b0 (9) eap: Previous EAP request found for state 0x93ae5ad093a740b0, released from the list (9) eap: Peer sent packet with method EAP MSCHAPv2 (26) (9) eap: Calling submodule eap_mschapv2 to process data (9) eap_mschapv2: Auth-Type sub-section not found. Ignoring. (9) eap_mschapv2: # Executing group from file /etc/raddb/sites-enabled/inner-tunnel (9) eap: Sending EAP Failure (code 4) ID 9 length 4 (9) eap: Freeing handler (9) [eap] = reject (9) } # authenticate = reject (9) Failed to authenticate the user (9) Login incorrect: [user_a] (from client localhost port 0 via TLS tunnel) (9) Using Post-Auth-Type Reject If I uncomment the following # For old names, too. mschap I'm able to authenticate a user in one realm but not the other. 21) # Executing group from file /etc/raddb/sites-enabled/inner-tunnel (21) authenticate { (21) eap: Expiring EAP session with state 0xf0a763cef0ae799b (21) eap: Finished EAP session with state 0xf0a763cef0ae799b (21) eap: Previous EAP request found for state 0xf0a763cef0ae799b, released from the list (21) eap: Peer sent packet with method EAP MSCHAPv2 (26) (21) eap: Calling submodule eap_mschapv2 to process data (21) eap_mschapv2: # Executing group from file /etc/raddb/sites-enabled/inner-tunnel (21) eap_mschapv2: authenticate { (21) mschap: Creating challenge hash with username: XXXXXX (21) mschap: Client is using MS-CHAPv2 (21) mschap: EXPAND %{Stripped-User-Name} (21) mschap: --> XXXXXX rlm_mschap (mschap): Reserved connection (1) (21) mschap: sending authentication request user='XXXXXX' domain='ADMIN' rlm_mschap (mschap): Released connection (1) rlm_mschap (mschap): Need 9 more connections to reach 20 spares rlm_mschap (mschap): Opening additional connection (11), 1 of 53 pending slots used (21) mschap: ERROR: No such user [0xC0000064] (21) mschap: ERROR: Password has expired. User should retry authentication (21) [mschap] = reject (21) } # authenticate = reject (21) eap: Sending EAP Failure (code 4) ID 9 length 4 (21) eap: Freeing handler (21) [eap] = reject (21) } # authenticate = reject (21) Failed to authenticate the user I

2 1

Fwd: Request-Authenticator attribute removed from accounting log
by Tom Carly 30 Jan '17

30 Jan '17

Hi, I'm using a 3.1.x build of a few days ago. In previous versions (don't know exactly when it changed), the accounting log contained "Request-Authenticator = verified" for each received message. It seems that this was removed recently. When parsing the log, I check whether this field is present. My questions: * Is there still a way to include this in the log? * if not, why was it removed? thanks in advance! Best regards, Tom Carly

2 1

Max length for User-Name
by Joe Friedeggs 30 Jan '17

30 Jan '17

Pertaining to User-Name, RFC2865 states in section 5.1: 0 1 2 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- | Type | Length | String ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- Type 1 for User-Name. Length >= 3 String The String field is one or more octets. The NAS may limit the maximum length of the User-Name but the ability to handle at least 63 octets is recommended. which recommends 'at least' 63 octets, but I see the sql (ver 2.2.6 with postgresql) set the limits the UserName to 'at most' 64 characters: CREATE TABLE radcheck ( id SERIAL PRIMARY KEY, UserName VARCHAR(64) NOT NULL DEFAULT '', ... It seems to me the limiting factor of the User-Name here should only the 'length' field, which is one octet, therefore limiting the User-Name string to 255 charaters (minus overhead?). Why is the UserName in the table limited to 64 characters? What is the reasoning behind this? Is there some other limiting factor? I have a case where we need to use longer user names. Thanks, Joe

6 6

AD Group Check - multi SSID - Pass "Require-membership-of" to NTLM_AUTH as variable.
by Pierre de Jong 30 Jan '17

30 Jan '17

Hi all, I am trying to set up a FreeRadius (v3.12 on debian8) to authenticate against MS Active Directory, with AD group membership requierement for "multiple SSID". So, for exemple, SSID-Corp-Employee is only accessible to a certain users, member of ADgroupA , and SSID-Corp-Direction, only accessible to users, member of ADgroupB When only authenticating with 1 single AD group, there is no problem, the : > ntlm_auth = "/usr/bin/ntlm_auth --request-nt-key > --require-membership-of=GALAXY\rad01 --username=%{%{Stripped-User-Name}:-%{%{User-Name}:-None}} > --domain=%{%{mschap:NT-Domain}:-GALAXY.PRIV} > --challenge=%{%{mschap:Challenge}:-00} --nt-response=%{%{mschap:NT-Re > sponse}:-00}" does the trick... So, what I thaught could be the easiest way, is to pass the "--require-membership-of=" as parameter... and even more, that AD group would be the same as the SSID ... So, when a new SSID is created, no need to change any in the freeradius, just create the AD group according to the SSID, and ... that's it. i put this in the Authorize section of "DEFAULT" and "inner-tunnel", just after the "filter_username" ############################################################ ############################# rewrite_called_station_id if (&Called-Station-SSID == "rad01") { update request { NTLM-Group-Required := "GALAXY\rad01" User-Name := "pierre" } } elsif (%Called-Station-SSID == "RAD02") { update request { NTLM-Group-Required := "GALAXY\RAD02" } } ############################################################ ############################# It seems that it's parsed correct: # policy rewrite_called_station_id = updated (76) if (&Called-Station-SSID == "rad01") { (76) if (&Called-Station-SSID == "rad01") -> TRUE (76) if (&Called-Station-SSID == "rad01") { (76) update request { (76) NTLM-Group-Required := "GALAXY\rad01" and my "NTLM_Auth" is the: ntlm_auth = "/usr/bin/ntlm_auth --request-nt-key > --require-membership-of=%NTLM-Group-Required > --username=%{%{Stripped-User-Name}:-%{%{User-Name}:-None}} > --domain=%{%{mschap:NT-Domain}:-GALAXY.PRIV} > --challenge=%{%{mschap:Challenge}:-00} --nt-response=%{%{mschap:NT-Re > sponse}:-00}" but it does not work... for information, if I replace %NTLM-Group-Required by GALAXY\rad01 it does work correct. Is there any way someone could give me advice on how to achieve this... or any other way to achieve this ? Of course, needless to say, I am no expert in "FreeRadius", so, please, excuses me if it's not the way to go, or if my assomption are wrond Thanks in advance for your reading and your time. I have join to the mail a attached file with "a radiusd -X" session.... (No idea if "attached files pass... sorry, not used the mailling list much so fare :-D ) Pierre de Jong

3 2

3.0.12 EAP-PEAP with OpenLDAP group membership and Packet-Src-IP-Address checking
by Staiger, Moritz (RRZE) 28 Jan '17

28 Jan '17

Hi, we are running freeradius 3.0.12 which is authenticating against an openldap server with EAP PEAP MSCHAPv2 In future we want to enable VLAN assignment via LDAP so we want to use LDAP group membership comparison and combine it with Packet-Src-IP-Address checking. Users from LDAP group „Admins“ should be assigned to VLAN 10 (management) Users from LDAP group „Operators“ should be assigned to VLAN 20 (operator) Users from other LDAP groups „Group-X“ should be assigned to userspecific VLAN which is represented in the LDAP attribute „radiusTunnelPrivateGroupId“. With group membership and Packet-Src-IP-Address we want to authenticate users only if they try to connect from their *home POP*. What we have done: 1. according to Alan DeKoks suggestions here: http://lists.freeradius.org/pipermail/freeradius-users/2015-April/077171.ht… configured freeradius/mods-enabled/ldap „group“ section for group checking. In our case every LDAP user has an LDAP attribute 'gidNumber' which represents its group membership. group { base_dn = "${..base_dn}" groupmembership_attribute = 'gidNumber' } 2. configured /freeradius/users file # in LDAP: Admins gidNumber = 111, Operators gidNumber = 222, Users in POP1 gidNumber = 901 DEFAULT LDAP-Group == "111", Auth-Type = LDAP DEFAULT LDAP-Group == "222", Auth-Type = LDAP DEFAULT Packet-Src-IP-Address == 10.0.0.1, LDAP-Group == „901“, Auth-Type = LDAP ... DEFAULT Packet-Src-IP-Address == 10.0.0.15, LDAP-Group == „915“, Auth-Type = LDAP DEFAULT Auth-Type := Reject # 3. configured /freeradius/sites-enabled/default >no "ldap" in the "authorize" section so ldap gets commented here -> #ldap >be sure there's "Auth-Type LDAP" in the "authenticate" section so #Auth-Type LDAP { # ldap # } gets uncommented here -> Auth-Type LDAP { ldap } 4. configured /freeradius/sites-enabled/inner-tunnel authorize { ldap authenticate { #Auth-Type LDAP { # ldap # } Within testing the config seems to do what we desire. So my questions are: Is this implementation correct for our needs? Is there a more elegant way to implement it? Is it possible to reduce the LDAP queries exept from sorting the POP listing in users file? (there seems to be a change in 3.0.13 ?) >From my readings of the log I think authentication is done twice against the LDAP? Do you have other hints or suggestions? Regards Moritz Ready to process requests (0) Received Access-Request Id 10 from 172.17.26.160:22492 to 172.17.28.67:1812 length 169 (0) User-Name = "Test-A" (0) NAS-Identifier = "44d9e7f96309" (0) NAS-Port = 0 (0) Called-Station-Id = "46-D9-E7-FA-63-09:SSID " (0) Calling-Station-Id = "60-A3-7D-2C-A2-19" (0) Framed-MTU = 1400 (0) NAS-Port-Type = Wireless-802.11 (0) Connect-Info = "CONNECT 0Mbps 802.11b" (0) EAP-Message = 0x02ab000b01546573742d41 (0) Message-Authenticator = 0x40ce940b690d606fe714b004361dc50d (0) # Executing section authorize from file /etc/freeradius/sites-enabled/default (0) authorize { (0) policy filter_username { (0) if (&User-Name) { (0) if (&User-Name) -> TRUE (0) if (&User-Name) { (0) if (&User-Name =~ / /) { (0) if (&User-Name =~ / /) -> FALSE (0) if (&User-Name =~ /@[^@]*@/ ) { (0) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (0) if (&User-Name =~ /\.\./ ) { (0) if (&User-Name =~ /\.\./ ) -> FALSE (0) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (0) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (0) if (&User-Name =~ /\.$/) { (0) if (&User-Name =~ /\.$/) -> FALSE (0) if (&User-Name =~ /(a)\./) { (0) if (&User-Name =~ /(a)\./) -> FALSE (0) } # if (&User-Name) = notfound (0) } # policy filter_username = notfound (0) [preprocess] = ok (0) [chap] = noop (0) [mschap] = noop (0) [digest] = noop (0) suffix: Checking for suffix after "@" (0) suffix: No '@' in User-Name = "Test-A", looking up realm NULL (0) suffix: No such realm "NULL" (0) [suffix] = noop (0) eap: Peer sent EAP Response (code 2) ID 171 length 11 (0) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize (0) [eap] = ok (0) } # authorize = ok (0) Found Auth-Type = eap (0) # Executing group from file /etc/freeradius/sites-enabled/default (0) authenticate { (0) eap: Peer sent packet with method EAP Identity (1) (0) eap: Calling submodule eap_peap to process data (0) eap_peap: Initiating new EAP-TLS session (0) eap_peap: Flushing SSL sessions (of #0) (0) eap_peap: [eaptls start] = request (0) eap: Sending EAP Request (code 1) ID 172 length 6 (0) eap: EAP session adding &reply:State = 0xe87b0b92e8d71203 (0) [eap] = handled (0) } # authenticate = handled (0) Using Post-Auth-Type Challenge (0) Post-Auth-Type sub-section not found. Ignoring. (0) # Executing group from file /etc/freeradius/sites-enabled/default (0) Sent Access-Challenge Id 10 from 172.17.28.67:1812 to 172.17.26.160:22492 length 0 (0) EAP-Message = 0x01ac00061920 (0) Message-Authenticator = 0x00000000000000000000000000000000 (0) State = 0xe87b0b92e8d7120391ed7d921e46c093 (0) Finished request Waking up in 4.9 seconds. (1) Received Access-Request Id 11 from 172.17.26.160:22492 to 172.17.28.67:1812 length 303 (1) User-Name = "Test-A" (1) NAS-Identifier = "44d9e7f96309" (1) NAS-Port = 0 (1) Called-Station-Id = "46-D9-E7-FA-63-09:SSID" (1) Calling-Station-Id = "60-A3-7D-2C-A2-19" (1) Framed-MTU = 1400 (1) NAS-Port-Type = Wireless-802.11 (1) Connect-Info = "CONNECT 0Mbps 802.11b" (1) EAP-Message = 0x02ac007f19800000007516030100700100006c030158765972f4d9369be37fc8bb9981e44d884bd092457985f8cfa9746c7e4a07de00002000ffc024c023c00ac009c008c028c027c014c013c012003d003c0035002f000a01000023000a00080006001700180019000b00020100000500050100000000 (1) State = 0xe87b0b92e8d7120391ed7d921e46c093 (1) Message-Authenticator = 0xc0e4bbed21698af0a845d633e7e1b98f (1) session-state: No cached attributes (1) # Executing section authorize from file /etc/freeradius/sites-enabled/default (1) authorize { (1) policy filter_username { (1) if (&User-Name) { (1) if (&User-Name) -> TRUE (1) if (&User-Name) { (1) if (&User-Name =~ / /) { (1) if (&User-Name =~ / /) -> FALSE (1) if (&User-Name =~ /@[^@]*@/ ) { (1) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (1) if (&User-Name =~ /\.\./ ) { (1) if (&User-Name =~ /\.\./ ) -> FALSE (1) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (1) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (1) if (&User-Name =~ /\.$/) { (1) if (&User-Name =~ /\.$/) -> FALSE (1) if (&User-Name =~ /(a)\./) { (1) if (&User-Name =~ /(a)\./) -> FALSE (1) } # if (&User-Name) = notfound (1) } # policy filter_username = notfound (1) [preprocess] = ok (1) [chap] = noop (1) [mschap] = noop (1) [digest] = noop (1) suffix: Checking for suffix after "@" (1) suffix: No '@' in User-Name = "Test-A", looking up realm NULL (1) suffix: No such realm "NULL" (1) [suffix] = noop (1) eap: Peer sent EAP Response (code 2) ID 172 length 127 (1) eap: Continuing tunnel setup (1) [eap] = ok (1) } # authorize = ok (1) Found Auth-Type = eap (1) # Executing group from file /etc/freeradius/sites-enabled/default (1) authenticate { (1) eap: Expiring EAP session with state 0xe87b0b92e8d71203 (1) eap: Finished EAP session with state 0xe87b0b92e8d71203 (1) eap: Previous EAP request found for state 0xe87b0b92e8d71203, released from the list (1) eap: Peer sent packet with method EAP PEAP (25) (1) eap: Calling submodule eap_peap to process data (1) eap_peap: Continuing EAP-TLS (1) eap_peap: Peer indicated complete TLS record size will be 117 bytes (1) eap_peap: Got complete TLS record (117 bytes) (1) eap_peap: [eaptls verify] = length included (1) eap_peap: (other): before/accept initialization (1) eap_peap: TLS_accept: before/accept initialization (1) eap_peap: <<< recv TLS 1.0 Handshake [length 0070], ClientHello (1) eap_peap: TLS_accept: SSLv3 read client hello A (1) eap_peap: >>> send TLS 1.0 Handshake [length 0059], ServerHello (1) eap_peap: TLS_accept: SSLv3 write server hello A (1) eap_peap: >>> send TLS 1.0 Handshake [length 0973], Certificate (1) eap_peap: TLS_accept: SSLv3 write certificate A (1) eap_peap: >>> send TLS 1.0 Handshake [length 014b], ServerKeyExchange (1) eap_peap: TLS_accept: SSLv3 write key exchange A (1) eap_peap: >>> send TLS 1.0 Handshake [length 0004], ServerHelloDone (1) eap_peap: TLS_accept: SSLv3 write server done A (1) eap_peap: TLS_accept: SSLv3 flush data (1) eap_peap: TLS_accept: Need to read more data: SSLv3 read client certificate A (1) eap_peap: TLS_accept: Need to read more data: SSLv3 read client certificate A (1) eap_peap: In SSL Handshake Phase (1) eap_peap: In SSL Accept mode (1) eap_peap: [eaptls process] = handled (1) eap: Sending EAP Request (code 1) ID 173 length 1004 (1) eap: EAP session adding &reply:State = 0xe87b0b92e9d61203 (1) [eap] = handled (1) } # authenticate = handled (1) Using Post-Auth-Type Challenge (1) Post-Auth-Type sub-section not found. Ignoring. (1) # Executing group from file /etc/freeradius/sites-enabled/default (1) Sent Access-Challenge Id 11 from 172.17.28.67:1812 to 172.17.26.160:22492 length 0 (1) EAP-Message = 0x01ad03ec19c000000b2f160301005902000055030146df3e492a751185c5d2365a274915dd496ab3909cfa2b581b8e0f058d35413e20d8f7784bdabc1d0f47bfe939b6a8b6ecf01f2acae83ea6f7a5a1dcff7b869c5fc01400000dff01000100000b00040300010216030109730b00096f00096c0004e9 (1) Message-Authenticator = 0x00000000000000000000000000000000 (1) State = 0xe87b0b92e9d6120391ed7d921e46c093 (1) Finished request Waking up in 4.9 seconds. (2) Received Access-Request Id 12 from 172.17.26.160:22492 to 172.17.28.67:1812 length 182 (2) User-Name = "Test-A" (2) NAS-Identifier = "44d9e7f96309" (2) NAS-Port = 0 (2) Called-Station-Id = "46-D9-E7-FA-63-09:SSID" (2) Calling-Station-Id = "60-A3-7D-2C-A2-19" (2) Framed-MTU = 1400 (2) NAS-Port-Type = Wireless-802.11 (2) Connect-Info = "CONNECT 0Mbps 802.11b" (2) EAP-Message = 0x02ad00061900 (2) State = 0xe87b0b92e9d6120391ed7d921e46c093 (2) Message-Authenticator = 0xce185ed0b264fb9f6d3d1be7d6991ed9 (2) session-state: No cached attributes (2) # Executing section authorize from file /etc/freeradius/sites-enabled/default (2) authorize { (2) policy filter_username { (2) if (&User-Name) { (2) if (&User-Name) -> TRUE (2) if (&User-Name) { (2) if (&User-Name =~ / /) { (2) if (&User-Name =~ / /) -> FALSE (2) if (&User-Name =~ /@[^@]*@/ ) { (2) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (2) if (&User-Name =~ /\.\./ ) { (2) if (&User-Name =~ /\.\./ ) -> FALSE (2) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (2) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (2) if (&User-Name =~ /\.$/) { (2) if (&User-Name =~ /\.$/) -> FALSE (2) if (&User-Name =~ /(a)\./) { (2) if (&User-Name =~ /(a)\./) -> FALSE (2) } # if (&User-Name) = notfound (2) } # policy filter_username = notfound (2) [preprocess] = ok (2) [chap] = noop (2) [mschap] = noop (2) [digest] = noop (2) suffix: Checking for suffix after "@" (2) suffix: No '@' in User-Name = "Test-A", looking up realm NULL (2) suffix: No such realm "NULL" (2) [suffix] = noop (2) eap: Peer sent EAP Response (code 2) ID 173 length 6 (2) eap: Continuing tunnel setup (2) [eap] = ok (2) } # authorize = ok (2) Found Auth-Type = eap (2) # Executing group from file /etc/freeradius/sites-enabled/default (2) authenticate { (2) eap: Expiring EAP session with state 0xe87b0b92e9d61203 (2) eap: Finished EAP session with state 0xe87b0b92e9d61203 (2) eap: Previous EAP request found for state 0xe87b0b92e9d61203, released from the list (2) eap: Peer sent packet with method EAP PEAP (25) (2) eap: Calling submodule eap_peap to process data (2) eap_peap: Continuing EAP-TLS (2) eap_peap: Peer ACKed our handshake fragment (2) eap_peap: [eaptls verify] = request (2) eap_peap: [eaptls process] = handled (2) eap: Sending EAP Request (code 1) ID 174 length 1000 (2) eap: EAP session adding &reply:State = 0xe87b0b92ead51203 (2) [eap] = handled (2) } # authenticate = handled (2) Using Post-Auth-Type Challenge (2) Post-Auth-Type sub-section not found. Ignoring. (2) # Executing group from file /etc/freeradius/sites-enabled/default (2) Sent Access-Challenge Id 12 from 172.17.28.67:1812 to 172.17.26.160:22492 length 0 (2) EAP-Message = 0x01ae03e81940864886f70d0109011613696e666f4064732d6e6574776f726b732e6465311c301a0603550403131344532d6e6574776f726b7320526f6f7420434182010030130603551d25040c300a06082b06010505070301300b0603551d0f0404030205a0300d06092a864886f70d01010b05000382 (2) Message-Authenticator = 0x00000000000000000000000000000000 (2) State = 0xe87b0b92ead5120391ed7d921e46c093 (2) Finished request Waking up in 4.9 seconds. (3) Received Access-Request Id 13 from 172.17.26.160:22492 to 172.17.28.67:1812 length 182 (3) User-Name = "Test-A" (3) NAS-Identifier = "44d9e7f96309" (3) NAS-Port = 0 (3) Called-Station-Id = "46-D9-E7-FA-63-09:SSID" (3) Calling-Station-Id = "60-A3-7D-2C-A2-19" (3) Framed-MTU = 1400 (3) NAS-Port-Type = Wireless-802.11 (3) Connect-Info = "CONNECT 0Mbps 802.11b" (3) EAP-Message = 0x02ae00061900 (3) State = 0xe87b0b92ead5120391ed7d921e46c093 (3) Message-Authenticator = 0xd445aca761a3735e0e685c2dcc8fa971 (3) session-state: No cached attributes (3) # Executing section authorize from file /etc/freeradius/sites-enabled/default (3) authorize { (3) policy filter_username { (3) if (&User-Name) { (3) if (&User-Name) -> TRUE (3) if (&User-Name) { (3) if (&User-Name =~ / /) { (3) if (&User-Name =~ / /) -> FALSE (3) if (&User-Name =~ /@[^@]*@/ ) { (3) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (3) if (&User-Name =~ /\.\./ ) { (3) if (&User-Name =~ /\.\./ ) -> FALSE (3) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (3) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (3) if (&User-Name =~ /\.$/) { (3) if (&User-Name =~ /\.$/) -> FALSE (3) if (&User-Name =~ /(a)\./) { (3) if (&User-Name =~ /(a)\./) -> FALSE (3) } # if (&User-Name) = notfound (3) } # policy filter_username = notfound (3) [preprocess] = ok (3) [chap] = noop (3) [mschap] = noop (3) [digest] = noop (3) suffix: Checking for suffix after "@" (3) suffix: No '@' in User-Name = "Test-A", looking up realm NULL (3) suffix: No such realm "NULL" (3) [suffix] = noop (3) eap: Peer sent EAP Response (code 2) ID 174 length 6 (3) eap: Continuing tunnel setup (3) [eap] = ok (3) } # authorize = ok (3) Found Auth-Type = eap (3) # Executing group from file /etc/freeradius/sites-enabled/default (3) authenticate { (3) eap: Expiring EAP session with state 0xe87b0b92ead51203 (3) eap: Finished EAP session with state 0xe87b0b92ead51203 (3) eap: Previous EAP request found for state 0xe87b0b92ead51203, released from the list (3) eap: Peer sent packet with method EAP PEAP (25) (3) eap: Calling submodule eap_peap to process data (3) eap_peap: Continuing EAP-TLS (3) eap_peap: Peer ACKed our handshake fragment (3) eap_peap: [eaptls verify] = request (3) eap_peap: [eaptls process] = handled (3) eap: Sending EAP Request (code 1) ID 175 length 881 (3) eap: EAP session adding &reply:State = 0xe87b0b92ebd41203 (3) [eap] = handled (3) } # authenticate = handled (3) Using Post-Auth-Type Challenge (3) Post-Auth-Type sub-section not found. Ignoring. (3) # Executing group from file /etc/freeradius/sites-enabled/default (3) Sent Access-Challenge Id 13 from 172.17.28.67:1812 to 172.17.26.160:22492 length 0 (3) EAP-Message = 0x01af03711900cd6b6a86ea145de10b316047370203010001a381e93081e6301d0603551d0e041604148cf1945262f33d0d656b8a1652dcfece15788e563081b60603551d230481ae3081ab80148cf1945262f33d0d656b8a1652dcfece15788e56a1818fa4818c308189310b3009060355040613024445 (3) Message-Authenticator = 0x00000000000000000000000000000000 (3) State = 0xe87b0b92ebd4120391ed7d921e46c093 (3) Finished request Waking up in 4.9 seconds. (4) Received Access-Request Id 14 from 172.17.26.160:22492 to 172.17.28.67:1812 length 320 (4) User-Name = "Test-A" (4) NAS-Identifier = "44d9e7f96309" (4) NAS-Port = 0 (4) Called-Station-Id = "46-D9-E7-FA-63-09:SSID" (4) Calling-Station-Id = "60-A3-7D-2C-A2-19" (4) Framed-MTU = 1400 (4) NAS-Port-Type = Wireless-802.11 (4) Connect-Info = "CONNECT 0Mbps 802.11b" (4) EAP-Message = 0x02af0090198000000086160301004610000042410401cc455cf06611016d46d4588fdabcc9e63f1e6b14b1e4c3f8b2751c0877946e4c33f0e0d7d3e654085be67b994f906af4085c629f2bb6a42a6d4d2d76c3ed711403010001011603010030cae54345ff3c41b7b02f025f040509ce0debe78eeee8c1 (4) State = 0xe87b0b92ebd4120391ed7d921e46c093 (4) Message-Authenticator = 0x1c43bb71884d24ef2d421f8da92bb934 (4) session-state: No cached attributes (4) # Executing section authorize from file /etc/freeradius/sites-enabled/default (4) authorize { (4) policy filter_username { (4) if (&User-Name) { (4) if (&User-Name) -> TRUE (4) if (&User-Name) { (4) if (&User-Name =~ / /) { (4) if (&User-Name =~ / /) -> FALSE (4) if (&User-Name =~ /@[^@]*@/ ) { (4) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (4) if (&User-Name =~ /\.\./ ) { (4) if (&User-Name =~ /\.\./ ) -> FALSE (4) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (4) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (4) if (&User-Name =~ /\.$/) { (4) if (&User-Name =~ /\.$/) -> FALSE (4) if (&User-Name =~ /(a)\./) { (4) if (&User-Name =~ /(a)\./) -> FALSE (4) } # if (&User-Name) = notfound (4) } # policy filter_username = notfound (4) [preprocess] = ok (4) [chap] = noop (4) [mschap] = noop (4) [digest] = noop (4) suffix: Checking for suffix after "@" (4) suffix: No '@' in User-Name = "Test-A", looking up realm NULL (4) suffix: No such realm "NULL" (4) [suffix] = noop (4) eap: Peer sent EAP Response (code 2) ID 175 length 144 (4) eap: Continuing tunnel setup (4) [eap] = ok (4) } # authorize = ok (4) Found Auth-Type = eap (4) # Executing group from file /etc/freeradius/sites-enabled/default (4) authenticate { (4) eap: Expiring EAP session with state 0xe87b0b92ebd41203 (4) eap: Finished EAP session with state 0xe87b0b92ebd41203 (4) eap: Previous EAP request found for state 0xe87b0b92ebd41203, released from the list (4) eap: Peer sent packet with method EAP PEAP (25) (4) eap: Calling submodule eap_peap to process data (4) eap_peap: Continuing EAP-TLS (4) eap_peap: Peer indicated complete TLS record size will be 134 bytes (4) eap_peap: Got complete TLS record (134 bytes) (4) eap_peap: [eaptls verify] = length included (4) eap_peap: <<< recv TLS 1.0 Handshake [length 0046], ClientKeyExchange (4) eap_peap: TLS_accept: SSLv3 read client key exchange A (4) eap_peap: <<< recv TLS 1.0 ChangeCipherSpec [length 0001] (4) eap_peap: <<< recv TLS 1.0 Handshake [length 0010], Finished (4) eap_peap: TLS_accept: SSLv3 read finished A (4) eap_peap: >>> send TLS 1.0 ChangeCipherSpec [length 0001] (4) eap_peap: TLS_accept: SSLv3 write change cipher spec A (4) eap_peap: >>> send TLS 1.0 Handshake [length 0010], Finished (4) eap_peap: TLS_accept: SSLv3 write finished A (4) eap_peap: TLS_accept: SSLv3 flush data (4) eap_peap: (other): SSL negotiation finished successfully (4) eap_peap: SSL Connection Established (4) eap_peap: [eaptls process] = handled (4) eap: Sending EAP Request (code 1) ID 176 length 65 (4) eap: EAP session adding &reply:State = 0xe87b0b92eccb1203 (4) [eap] = handled (4) } # authenticate = handled (4) Using Post-Auth-Type Challenge (4) Post-Auth-Type sub-section not found. Ignoring. (4) # Executing group from file /etc/freeradius/sites-enabled/default (4) Sent Access-Challenge Id 14 from 172.17.28.67:1812 to 172.17.26.160:22492 length 0 (4) EAP-Message = 0x01b00041190014030100010116030100304aa51dcb700d63eea2551558c6204ef8229c47b635353d30613a28fe2d4422ca909b5f2d831e17bba1c7a51b659e7f23 (4) Message-Authenticator = 0x00000000000000000000000000000000 (4) State = 0xe87b0b92eccb120391ed7d921e46c093 (4) Finished request Waking up in 4.8 seconds. (5) Received Access-Request Id 15 from 172.17.26.160:22492 to 172.17.28.67:1812 length 182 (5) User-Name = "Test-A" (5) NAS-Identifier = "44d9e7f96309" (5) NAS-Port = 0 (5) Called-Station-Id = "46-D9-E7-FA-63-09:SSID" (5) Calling-Station-Id = "60-A3-7D-2C-A2-19" (5) Framed-MTU = 1400 (5) NAS-Port-Type = Wireless-802.11 (5) Connect-Info = "CONNECT 0Mbps 802.11b" (5) EAP-Message = 0x02b000061900 (5) State = 0xe87b0b92eccb120391ed7d921e46c093 (5) Message-Authenticator = 0x8ab0a46258fcf64773c9b362e671f7ac (5) session-state: No cached attributes (5) # Executing section authorize from file /etc/freeradius/sites-enabled/default (5) authorize { (5) policy filter_username { (5) if (&User-Name) { (5) if (&User-Name) -> TRUE (5) if (&User-Name) { (5) if (&User-Name =~ / /) { (5) if (&User-Name =~ / /) -> FALSE (5) if (&User-Name =~ /@[^@]*@/ ) { (5) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (5) if (&User-Name =~ /\.\./ ) { (5) if (&User-Name =~ /\.\./ ) -> FALSE (5) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (5) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (5) if (&User-Name =~ /\.$/) { (5) if (&User-Name =~ /\.$/) -> FALSE (5) if (&User-Name =~ /(a)\./) { (5) if (&User-Name =~ /(a)\./) -> FALSE (5) } # if (&User-Name) = notfound (5) } # policy filter_username = notfound (5) [preprocess] = ok (5) [chap] = noop (5) [mschap] = noop (5) [digest] = noop (5) suffix: Checking for suffix after "@" (5) suffix: No '@' in User-Name = "Test-A", looking up realm NULL (5) suffix: No such realm "NULL" (5) [suffix] = noop (5) eap: Peer sent EAP Response (code 2) ID 176 length 6 (5) eap: Continuing tunnel setup (5) [eap] = ok (5) } # authorize = ok (5) Found Auth-Type = eap (5) # Executing group from file /etc/freeradius/sites-enabled/default (5) authenticate { (5) eap: Expiring EAP session with state 0xe87b0b92eccb1203 (5) eap: Finished EAP session with state 0xe87b0b92eccb1203 (5) eap: Previous EAP request found for state 0xe87b0b92eccb1203, released from the list (5) eap: Peer sent packet with method EAP PEAP (25) (5) eap: Calling submodule eap_peap to process data (5) eap_peap: Continuing EAP-TLS (5) eap_peap: Peer ACKed our handshake fragment. handshake is finished (5) eap_peap: [eaptls verify] = success (5) eap_peap: [eaptls process] = success (5) eap_peap: Session established. Decoding tunneled attributes (5) eap_peap: PEAP state TUNNEL ESTABLISHED (5) eap: Sending EAP Request (code 1) ID 177 length 43 (5) eap: EAP session adding &reply:State = 0xe87b0b92edca1203 (5) [eap] = handled (5) } # authenticate = handled (5) Using Post-Auth-Type Challenge (5) Post-Auth-Type sub-section not found. Ignoring. (5) # Executing group from file /etc/freeradius/sites-enabled/default (5) Sent Access-Challenge Id 15 from 172.17.28.67:1812 to 172.17.26.160:22492 length 0 (5) EAP-Message = 0x01b1002b19001703010020550050cf49a4170b4a5068088207c5f2a56e3f68e382a25e59ab3e8996402ab4 (5) Message-Authenticator = 0x00000000000000000000000000000000 (5) State = 0xe87b0b92edca120391ed7d921e46c093 (5) Finished request Waking up in 4.8 seconds. (6) Received Access-Request Id 16 from 172.17.26.160:22492 to 172.17.28.67:1812 length 219 (6) User-Name = "Test-A" (6) NAS-Identifier = "44d9e7f96309" (6) NAS-Port = 0 (6) Called-Station-Id = "46-D9-E7-FA-63-09:SSID" (6) Calling-Station-Id = "60-A3-7D-2C-A2-19" (6) Framed-MTU = 1400 (6) NAS-Port-Type = Wireless-802.11 (6) Connect-Info = "CONNECT 0Mbps 802.11b" (6) EAP-Message = 0x02b1002b19001703010020b565bc67f5cc3d10ece5c5da4177ef58267599d6b64681980823dbb0c1808b85 (6) State = 0xe87b0b92edca120391ed7d921e46c093 (6) Message-Authenticator = 0x714328f5012221ee7cdeab6006a4d7cc (6) session-state: No cached attributes (6) # Executing section authorize from file /etc/freeradius/sites-enabled/default (6) authorize { (6) policy filter_username { (6) if (&User-Name) { (6) if (&User-Name) -> TRUE (6) if (&User-Name) { (6) if (&User-Name =~ / /) { (6) if (&User-Name =~ / /) -> FALSE (6) if (&User-Name =~ /@[^@]*@/ ) { (6) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (6) if (&User-Name =~ /\.\./ ) { (6) if (&User-Name =~ /\.\./ ) -> FALSE (6) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (6) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (6) if (&User-Name =~ /\.$/) { (6) if (&User-Name =~ /\.$/) -> FALSE (6) if (&User-Name =~ /(a)\./) { (6) if (&User-Name =~ /(a)\./) -> FALSE (6) } # if (&User-Name) = notfound (6) } # policy filter_username = notfound (6) [preprocess] = ok (6) [chap] = noop (6) [mschap] = noop (6) [digest] = noop (6) suffix: Checking for suffix after "@" (6) suffix: No '@' in User-Name = "Test-A", looking up realm NULL (6) suffix: No such realm "NULL" (6) [suffix] = noop (6) eap: Peer sent EAP Response (code 2) ID 177 length 43 (6) eap: Continuing tunnel setup (6) [eap] = ok (6) } # authorize = ok (6) Found Auth-Type = eap (6) # Executing group from file /etc/freeradius/sites-enabled/default (6) authenticate { (6) eap: Expiring EAP session with state 0xe87b0b92edca1203 (6) eap: Finished EAP session with state 0xe87b0b92edca1203 (6) eap: Previous EAP request found for state 0xe87b0b92edca1203, released from the list (6) eap: Peer sent packet with method EAP PEAP (25) (6) eap: Calling submodule eap_peap to process data (6) eap_peap: Continuing EAP-TLS (6) eap_peap: [eaptls verify] = ok (6) eap_peap: Done initial handshake (6) eap_peap: [eaptls process] = ok (6) eap_peap: Session established. Decoding tunneled attributes (6) eap_peap: PEAP state WAITING FOR INNER IDENTITY (6) eap_peap: Identity - Test-A (6) eap_peap: Got inner identity 'Test-A' (6) eap_peap: Setting default EAP type for tunneled EAP session (6) eap_peap: Got tunneled request (6) eap_peap: EAP-Message = 0x02b1000b01546573742d41 (6) eap_peap: Setting User-Name to Test-A (6) eap_peap: Sending tunneled request to inner-tunnel (6) eap_peap: EAP-Message = 0x02b1000b01546573742d41 (6) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1 (6) eap_peap: User-Name = "Test-A" (6) Virtual server inner-tunnel received request (6) EAP-Message = 0x02b1000b01546573742d41 (6) FreeRADIUS-Proxied-To = 127.0.0.1 (6) User-Name = "Test-A" (6) WARNING: Outer and inner identities are the same. User privacy is compromised. (6) server inner-tunnel { (6) # Executing section authorize from file /etc/freeradius/sites-enabled/inner-tunnel (6) authorize { (6) policy filter_username { (6) if (&User-Name) { (6) if (&User-Name) -> TRUE (6) if (&User-Name) { (6) if (&User-Name =~ / /) { (6) if (&User-Name =~ / /) -> FALSE (6) if (&User-Name =~ /@[^@]*@/ ) { (6) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (6) if (&User-Name =~ /\.\./ ) { (6) if (&User-Name =~ /\.\./ ) -> FALSE (6) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (6) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (6) if (&User-Name =~ /\.$/) { (6) if (&User-Name =~ /\.$/) -> FALSE (6) if (&User-Name =~ /(a)\./) { (6) if (&User-Name =~ /(a)\./) -> FALSE (6) } # if (&User-Name) = notfound (6) } # policy filter_username = notfound (6) [chap] = noop (6) [mschap] = noop (6) suffix: Checking for suffix after "@" (6) suffix: No '@' in User-Name = "Test-A", looking up realm NULL (6) suffix: No such realm "NULL" (6) [suffix] = noop (6) update control { (6) &Proxy-To-Realm := LOCAL (6) } # update control = noop (6) eap: Peer sent EAP Response (code 2) ID 177 length 11 (6) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize (6) [eap] = ok (6) } # authorize = ok (6) Found Auth-Type = eap (6) # Executing group from file /etc/freeradius/sites-enabled/inner-tunnel (6) authenticate { (6) eap: Peer sent packet with method EAP Identity (1) (6) eap: Calling submodule eap_mschapv2 to process data (6) eap_mschapv2: Issuing Challenge (6) eap: Sending EAP Request (code 1) ID 178 length 43 (6) eap: EAP session adding &reply:State = 0xec7a3beaecc821b2 (6) [eap] = handled (6) } # authenticate = handled (6) } # server inner-tunnel (6) Virtual server sending reply (6) EAP-Message = 0x01b2002b1a01b2002610b6b7394c705a6ea01ef745eb87cbbf15667265657261646975732d332e302e3132 (6) Message-Authenticator = 0x00000000000000000000000000000000 (6) State = 0xec7a3beaecc821b29dbc50eda2d30e1d (6) eap_peap: Got tunneled reply code 11 (6) eap_peap: EAP-Message = 0x01b2002b1a01b2002610b6b7394c705a6ea01ef745eb87cbbf15667265657261646975732d332e302e3132 (6) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (6) eap_peap: State = 0xec7a3beaecc821b29dbc50eda2d30e1d (6) eap_peap: Got tunneled reply RADIUS code 11 (6) eap_peap: EAP-Message = 0x01b2002b1a01b2002610b6b7394c705a6ea01ef745eb87cbbf15667265657261646975732d332e302e3132 (6) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (6) eap_peap: State = 0xec7a3beaecc821b29dbc50eda2d30e1d (6) eap_peap: Got tunneled Access-Challenge (6) eap: Sending EAP Request (code 1) ID 178 length 75 (6) eap: EAP session adding &reply:State = 0xe87b0b92eec91203 (6) [eap] = handled (6) } # authenticate = handled (6) Using Post-Auth-Type Challenge (6) Post-Auth-Type sub-section not found. Ignoring. (6) # Executing group from file /etc/freeradius/sites-enabled/default (6) Sent Access-Challenge Id 16 from 172.17.28.67:1812 to 172.17.26.160:22492 length 0 (6) EAP-Message = 0x01b2004b19001703010040f6b8b1f8f68b3a43e03787d98680f81264a9a22945668477cd66d5742465b9b441aa72d6644170ed5baf4259d26fbaec1b1d82c2b7646a93bfe36d5fd569aa87 (6) Message-Authenticator = 0x00000000000000000000000000000000 (6) State = 0xe87b0b92eec9120391ed7d921e46c093 (6) Finished request Waking up in 4.8 seconds. (7) Received Access-Request Id 17 from 172.17.26.160:22492 to 172.17.28.67:1812 length 283 (7) User-Name = "Test-A" (7) NAS-Identifier = "44d9e7f96309" (7) NAS-Port = 0 (7) Called-Station-Id = "46-D9-E7-FA-63-09:SSID" (7) Calling-Station-Id = "60-A3-7D-2C-A2-19" (7) Framed-MTU = 1400 (7) NAS-Port-Type = Wireless-802.11 (7) Connect-Info = "CONNECT 0Mbps 802.11b" (7) EAP-Message = 0x02b2006b190017030100601be51d9a2c77ae2394716398c49829473527d582098388162a81d1816ffafebc692107a6083e06185c246a89e24dea141fe8b20fb1c70b88099c634417747fa15ab632014b1726a3c0ddb10ea805bdd74ee5adac6a731cd2a77215192fad8024 (7) State = 0xe87b0b92eec9120391ed7d921e46c093 (7) Message-Authenticator = 0x93493329818005c84c715c4ba53ffd49 (7) session-state: No cached attributes (7) # Executing section authorize from file /etc/freeradius/sites-enabled/default (7) authorize { (7) policy filter_username { (7) if (&User-Name) { (7) if (&User-Name) -> TRUE (7) if (&User-Name) { (7) if (&User-Name =~ / /) { (7) if (&User-Name =~ / /) -> FALSE (7) if (&User-Name =~ /@[^@]*@/ ) { (7) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (7) if (&User-Name =~ /\.\./ ) { (7) if (&User-Name =~ /\.\./ ) -> FALSE (7) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (7) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (7) if (&User-Name =~ /\.$/) { (7) if (&User-Name =~ /\.$/) -> FALSE (7) if (&User-Name =~ /(a)\./) { (7) if (&User-Name =~ /(a)\./) -> FALSE (7) } # if (&User-Name) = notfound (7) } # policy filter_username = notfound (7) [preprocess] = ok (7) [chap] = noop (7) [mschap] = noop (7) [digest] = noop (7) suffix: Checking for suffix after "@" (7) suffix: No '@' in User-Name = "Test-A", looking up realm NULL (7) suffix: No such realm "NULL" (7) [suffix] = noop (7) eap: Peer sent EAP Response (code 2) ID 178 length 107 (7) eap: Continuing tunnel setup (7) [eap] = ok (7) } # authorize = ok (7) Found Auth-Type = eap (7) # Executing group from file /etc/freeradius/sites-enabled/default (7) authenticate { (7) eap: Expiring EAP session with state 0xec7a3beaecc821b2 (7) eap: Finished EAP session with state 0xe87b0b92eec91203 (7) eap: Previous EAP request found for state 0xe87b0b92eec91203, released from the list (7) eap: Peer sent packet with method EAP PEAP (25) (7) eap: Calling submodule eap_peap to process data (7) eap_peap: Continuing EAP-TLS (7) eap_peap: [eaptls verify] = ok (7) eap_peap: Done initial handshake (7) eap_peap: [eaptls process] = ok (7) eap_peap: Session established. Decoding tunneled attributes (7) eap_peap: PEAP state phase2 (7) eap_peap: EAP method MSCHAPv2 (26) (7) eap_peap: Got tunneled request (7) eap_peap: EAP-Message = 0x02b200411a02b2003c314986e0f6871925a9900996f50368b8c30000000000000000170156e0b81df447dc98761a094eec647dbcdb8bfd2a54cc00546573742d41 (7) eap_peap: Setting User-Name to Test-A (7) eap_peap: Sending tunneled request to inner-tunnel (7) eap_peap: EAP-Message = 0x02b200411a02b2003c314986e0f6871925a9900996f50368b8c30000000000000000170156e0b81df447dc98761a094eec647dbcdb8bfd2a54cc00546573742d41 (7) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1 (7) eap_peap: User-Name = "Test-A" (7) eap_peap: State = 0xec7a3beaecc821b29dbc50eda2d30e1d (7) Virtual server inner-tunnel received request (7) EAP-Message = 0x02b200411a02b2003c314986e0f6871925a9900996f50368b8c30000000000000000170156e0b81df447dc98761a094eec647dbcdb8bfd2a54cc00546573742d41 (7) FreeRADIUS-Proxied-To = 127.0.0.1 (7) User-Name = "Test-A" (7) State = 0xec7a3beaecc821b29dbc50eda2d30e1d (7) WARNING: Outer and inner identities are the same. User privacy is compromised. (7) server inner-tunnel { (7) session-state: No cached attributes (7) # Executing section authorize from file /etc/freeradius/sites-enabled/inner-tunnel (7) authorize { (7) policy filter_username { (7) if (&User-Name) { (7) if (&User-Name) -> TRUE (7) if (&User-Name) { (7) if (&User-Name =~ / /) { (7) if (&User-Name =~ / /) -> FALSE (7) if (&User-Name =~ /@[^@]*@/ ) { (7) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (7) if (&User-Name =~ /\.\./ ) { (7) if (&User-Name =~ /\.\./ ) -> FALSE (7) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (7) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (7) if (&User-Name =~ /\.$/) { (7) if (&User-Name =~ /\.$/) -> FALSE (7) if (&User-Name =~ /(a)\./) { (7) if (&User-Name =~ /(a)\./) -> FALSE (7) } # if (&User-Name) = notfound (7) } # policy filter_username = notfound (7) [chap] = noop (7) [mschap] = noop (7) suffix: Checking for suffix after "@" (7) suffix: No '@' in User-Name = "Test-A", looking up realm NULL (7) suffix: No such realm "NULL" (7) [suffix] = noop (7) update control { (7) &Proxy-To-Realm := LOCAL (7) } # update control = noop (7) eap: Peer sent EAP Response (code 2) ID 178 length 65 (7) eap: No EAP Start, assuming it's an on-going EAP conversation (7) [eap] = updated (7) files: Searching for user in group "601" rlm_ldap (ldap): Reserved connection (0) (7) files: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (7) files: --> (uid=Test-A) (7) files: Performing search in "cn=users,dc=domain,dc=de" with filter "(uid=Test-A)", scope "sub" (7) files: Waiting for search result... (7) files: User object found at DN "uid=Test-A,cn=Admins,cn=users,dc=domain,dc=de" (7) files: Checking user object's gidNumber attributes (7) files: Performing unfiltered search in "uid=Test-A,cn=Admins,cn=users,dc=domain,dc=de", scope "base" (7) files: Waiting for search result... (7) files: Processing gidNumber value "601" as a group name (7) files: User found in group "601". Comparison between membership: name, check: name rlm_ldap (ldap): Released connection (0) rlm_ldap (ldap): Need 5 more connections to reach 10 spares rlm_ldap (ldap): Opening additional connection (5), 1 of 27 pending slots used rlm_ldap (ldap): Connecting to ldap://ldap.domain.de:389 rlm_ldap (ldap): Waiting for bind result... rlm_ldap (ldap): Bind successful (7) files: users: Matched entry DEFAULT at line 93 (7) [files] = ok rlm_ldap (ldap): Reserved connection (1) (7) ldap: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (7) ldap: --> (uid=Test-A) (7) ldap: Performing search in "cn=users,dc=domain,dc=de" with filter "(uid=Test-A)", scope "sub" (7) ldap: Waiting for search result... (7) ldap: User object found at DN "uid=Test-A,cn=Admins,cn=users,dc=domains,dc=de" (7) ldap: Processing user attributes (7) ldap: control:Password-With-Header += 'passwd' (7) ldap: reply:Tunnel-Type := VLAN (7) ldap: reply:Tunnel-Medium-Type := IEEE-802 (7) ldap: reply:Tunnel-Private-Group-ID := '1006' rlm_ldap (ldap): Released connection (1) (7) [ldap] = updated (7) [expiration] = noop (7) [logintime] = noop (7) pap: No {...} in Password-With-Header, re-writing to Cleartext-Password (7) pap: Removing &control:Password-With-Header (7) pap: WARNING: Auth-Type already set. Not setting to PAP (7) [pap] = noop (7) } # authorize = updated (7) Found Auth-Type = eap (7) # Executing group from file /etc/freeradius/sites-enabled/inner-tunnel (7) authenticate { (7) eap: Expiring EAP session with state 0xec7a3beaecc821b2 (7) eap: Finished EAP session with state 0xec7a3beaecc821b2 (7) eap: Previous EAP request found for state 0xec7a3beaecc821b2, released from the list (7) eap: Peer sent packet with method EAP MSCHAPv2 (26) (7) eap: Calling submodule eap_mschapv2 to process data (7) eap_mschapv2: # Executing group from file /etc/freeradius/sites-enabled/inner-tunnel (7) eap_mschapv2: authenticate { (7) mschap: Found Cleartext-Password, hashing to create NT-Password (7) mschap: Found Cleartext-Password, hashing to create LM-Password (7) mschap: Creating challenge hash with username: Test-A (7) mschap: Client is using MS-CHAPv2 (7) mschap: Adding MS-CHAPv2 MPPE keys (7) [mschap] = ok (7) } # authenticate = ok (7) MSCHAP Success (7) eap: Sending EAP Request (code 1) ID 179 length 51 (7) eap: EAP session adding &reply:State = 0xec7a3beaedc921b2 (7) [eap] = handled (7) } # authenticate = handled (7) } # server inner-tunnel (7) Virtual server sending reply (7) Tunnel-Type := VLAN (7) Tunnel-Medium-Type := IEEE-802 (7) Tunnel-Private-Group-Id := "1006" (7) EAP-Message = 0x01b300331a03b2002e533d30434644454436304345463344454633424543313439333738343531463242413030313242463032 (7) Message-Authenticator = 0x00000000000000000000000000000000 (7) State = 0xec7a3beaedc921b29dbc50eda2d30e1d (7) eap_peap: Got tunneled reply code 11 (7) eap_peap: Tunnel-Type := VLAN (7) eap_peap: Tunnel-Medium-Type := IEEE-802 (7) eap_peap: Tunnel-Private-Group-Id := "1006" (7) eap_peap: EAP-Message = 0x01b300331a03b2002e533d30434644454436304345463344454633424543313439333738343531463242413030313242463032 (7) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (7) eap_peap: State = 0xec7a3beaedc921b29dbc50eda2d30e1d (7) eap_peap: Got tunneled reply RADIUS code 11 (7) eap_peap: Tunnel-Type := VLAN (7) eap_peap: Tunnel-Medium-Type := IEEE-802 (7) eap_peap: Tunnel-Private-Group-Id := "1006" (7) eap_peap: EAP-Message = 0x01b300331a03b2002e533d30434644454436304345463344454633424543313439333738343531463242413030313242463032 (7) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (7) eap_peap: State = 0xec7a3beaedc921b29dbc50eda2d30e1d (7) eap_peap: Got tunneled Access-Challenge (7) eap: Sending EAP Request (code 1) ID 179 length 91 (7) eap: EAP session adding &reply:State = 0xe87b0b92efc81203 (7) [eap] = handled (7) } # authenticate = handled (7) Using Post-Auth-Type Challenge (7) Post-Auth-Type sub-section not found. Ignoring. (7) # Executing group from file /etc/freeradius/sites-enabled/default (7) Sent Access-Challenge Id 17 from 172.17.28.67:1812 to 172.17.26.160:22492 length 0 (7) EAP-Message = 0x01b3005b1900170301005085e76d76b7fd26ed339a2318366b5864e8da7bdf59ac3951a290d8098cd8ec1a1ee437eae651d55ef8440cc22c9f96f4a8cd676bea605c88b03571e8edc7cb94b8788a01842aa082aa9429c7640a8d3c (7) Message-Authenticator = 0x00000000000000000000000000000000 (7) State = 0xe87b0b92efc8120391ed7d921e46c093 (7) Finished request Waking up in 4.6 seconds. (8) Received Access-Request Id 18 from 172.17.26.160:22492 to 172.17.28.67:1812 length 219 (8) User-Name = "Test-A" (8) NAS-Identifier = "44d9e7f96309" (8) NAS-Port = 0 (8) Called-Station-Id = "46-D9-E7-FA-63-09:SSID" (8) Calling-Station-Id = "60-A3-7D-2C-A2-19" (8) Framed-MTU = 1400 (8) NAS-Port-Type = Wireless-802.11 (8) Connect-Info = "CONNECT 0Mbps 802.11b" (8) EAP-Message = 0x02b3002b190017030100204c0ba5e15af0320dd9bdd0045a3219ec189d7f5989cd57eece0e8988224b22b8 (8) State = 0xe87b0b92efc8120391ed7d921e46c093 (8) Message-Authenticator = 0x1a853cc4e2cdbee13432326a5dd503b5 (8) session-state: No cached attributes (8) # Executing section authorize from file /etc/freeradius/sites-enabled/default (8) authorize { (8) policy filter_username { (8) if (&User-Name) { (8) if (&User-Name) -> TRUE (8) if (&User-Name) { (8) if (&User-Name =~ / /) { (8) if (&User-Name =~ / /) -> FALSE (8) if (&User-Name =~ /@[^@]*@/ ) { (8) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (8) if (&User-Name =~ /\.\./ ) { (8) if (&User-Name =~ /\.\./ ) -> FALSE (8) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (8) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (8) if (&User-Name =~ /\.$/) { (8) if (&User-Name =~ /\.$/) -> FALSE (8) if (&User-Name =~ /(a)\./) { (8) if (&User-Name =~ /(a)\./) -> FALSE (8) } # if (&User-Name) = notfound (8) } # policy filter_username = notfound (8) [preprocess] = ok (8) [chap] = noop (8) [mschap] = noop (8) [digest] = noop (8) suffix: Checking for suffix after "@" (8) suffix: No '@' in User-Name = "Test-A", looking up realm NULL (8) suffix: No such realm "NULL" (8) [suffix] = noop (8) eap: Peer sent EAP Response (code 2) ID 179 length 43 (8) eap: Continuing tunnel setup (8) [eap] = ok (8) } # authorize = ok (8) Found Auth-Type = eap (8) # Executing group from file /etc/freeradius/sites-enabled/default (8) authenticate { (8) eap: Expiring EAP session with state 0xec7a3beaedc921b2 (8) eap: Finished EAP session with state 0xe87b0b92efc81203 (8) eap: Previous EAP request found for state 0xe87b0b92efc81203, released from the list (8) eap: Peer sent packet with method EAP PEAP (25) (8) eap: Calling submodule eap_peap to process data (8) eap_peap: Continuing EAP-TLS (8) eap_peap: [eaptls verify] = ok (8) eap_peap: Done initial handshake (8) eap_peap: [eaptls process] = ok (8) eap_peap: Session established. Decoding tunneled attributes (8) eap_peap: PEAP state phase2 (8) eap_peap: EAP method MSCHAPv2 (26) (8) eap_peap: Got tunneled request (8) eap_peap: EAP-Message = 0x02b300061a03 (8) eap_peap: Setting User-Name to Test-A (8) eap_peap: Sending tunneled request to inner-tunnel (8) eap_peap: EAP-Message = 0x02b300061a03 (8) eap_peap: FreeRADIUS-Proxied-To = 127.0.0.1 (8) eap_peap: User-Name = "Test-A" (8) eap_peap: State = 0xec7a3beaedc921b29dbc50eda2d30e1d (8) Virtual server inner-tunnel received request (8) EAP-Message = 0x02b300061a03 (8) FreeRADIUS-Proxied-To = 127.0.0.1 (8) User-Name = "Test-A" (8) State = 0xec7a3beaedc921b29dbc50eda2d30e1d (8) WARNING: Outer and inner identities are the same. User privacy is compromised. (8) server inner-tunnel { (8) session-state: No cached attributes (8) # Executing section authorize from file /etc/freeradius/sites-enabled/inner-tunnel (8) authorize { (8) policy filter_username { (8) if (&User-Name) { (8) if (&User-Name) -> TRUE (8) if (&User-Name) { (8) if (&User-Name =~ / /) { (8) if (&User-Name =~ / /) -> FALSE (8) if (&User-Name =~ /@[^@]*@/ ) { (8) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (8) if (&User-Name =~ /\.\./ ) { (8) if (&User-Name =~ /\.\./ ) -> FALSE (8) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (8) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (8) if (&User-Name =~ /\.$/) { (8) if (&User-Name =~ /\.$/) -> FALSE (8) if (&User-Name =~ /(a)\./) { (8) if (&User-Name =~ /(a)\./) -> FALSE (8) } # if (&User-Name) = notfound (8) } # policy filter_username = notfound (8) [chap] = noop (8) [mschap] = noop (8) suffix: Checking for suffix after "@" (8) suffix: No '@' in User-Name = "Test-A", looking up realm NULL (8) suffix: No such realm "NULL" (8) [suffix] = noop (8) update control { (8) &Proxy-To-Realm := LOCAL (8) } # update control = noop (8) eap: Peer sent EAP Response (code 2) ID 179 length 6 (8) eap: No EAP Start, assuming it's an on-going EAP conversation (8) [eap] = updated (8) files: Searching for user in group "601" rlm_ldap (ldap): Reserved connection (2) (8) files: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (8) files: --> (uid=Test-A) (8) files: Performing search in "cn=users,dc=domain,dc=de" with filter "(uid=Test-A)", scope "sub" (8) files: Waiting for search result... (8) files: User object found at DN "uid=Test-A,cn=Admins,cn=users,dc=domain,dc=de" (8) files: Checking user object's gidNumber attributes (8) files: Performing unfiltered search in "uid=Test-A,cn=Admins,cn=users,dc=domain,dc=de", scope "base" (8) files: Waiting for search result... (8) files: Processing gidNumber value "601" as a group name (8) files: User found in group "601". Comparison between membership: name, check: name rlm_ldap (ldap): Released connection (2) rlm_ldap (ldap): Need 4 more connections to reach 10 spares rlm_ldap (ldap): Opening additional connection (6), 1 of 26 pending slots used rlm_ldap (ldap): Connecting to ldap://ldap.domain.de:389 rlm_ldap (ldap): Waiting for bind result... rlm_ldap (ldap): Bind successful (8) files: users: Matched entry DEFAULT at line 93 (8) [files] = ok rlm_ldap (ldap): Reserved connection (3) (8) ldap: EXPAND (uid=%{%{Stripped-User-Name}:-%{User-Name}}) (8) ldap: --> (uid=Test-A) (8) ldap: Performing search in "cn=users,dc=domain,dc=de" with filter "(uid=Test-A)", scope "sub" (8) ldap: Waiting for search result... (8) ldap: User object found at DN "uid=Test-A,cn=Admins,cn=users,dc=domain,dc=de" (8) ldap: Processing user attributes (8) ldap: control:Password-With-Header += 'passwd' (8) ldap: reply:Tunnel-Type := VLAN (8) ldap: reply:Tunnel-Medium-Type := IEEE-802 (8) ldap: reply:Tunnel-Private-Group-ID := '1006' rlm_ldap (ldap): Released connection (3) (8) [ldap] = updated (8) [expiration] = noop (8) [logintime] = noop (8) pap: No {...} in Password-With-Header, re-writing to Cleartext-Password (8) pap: Removing &control:Password-With-Header (8) pap: WARNING: Auth-Type already set. Not setting to PAP (8) [pap] = noop (8) } # authorize = updated (8) Found Auth-Type = eap (8) # Executing group from file /etc/freeradius/sites-enabled/inner-tunnel (8) authenticate { (8) eap: Expiring EAP session with state 0xec7a3beaedc921b2 (8) eap: Finished EAP session with state 0xec7a3beaedc921b2 (8) eap: Previous EAP request found for state 0xec7a3beaedc921b2, released from the list (8) eap: Peer sent packet with method EAP MSCHAPv2 (26) (8) eap: Calling submodule eap_mschapv2 to process data (8) eap: Sending EAP Success (code 3) ID 179 length 4 (8) eap: Freeing handler (8) [eap] = ok (8) } # authenticate = ok (8) # Executing section post-auth from file /etc/freeradius/sites-enabled/inner-tunnel (8) post-auth { (8) update { (8) &outer.session-state::Tunnel-Type += &reply:Tunnel-Type[*] -> VLAN (8) &outer.session-state::Tunnel-Medium-Type += &reply:Tunnel-Medium-Type[*] -> IEEE-802 (8) &outer.session-state::Tunnel-Private-Group-Id += &reply:Tunnel-Private-Group-Id[*] -> '1006' (8) &outer.session-state::MS-MPPE-Encryption-Policy += &reply:MS-MPPE-Encryption-Policy[*] -> Encryption-Allowed (8) &outer.session-state::MS-MPPE-Encryption-Types += &reply:MS-MPPE-Encryption-Types[*] -> RC4-40or128-bit-Allowed (8) &outer.session-state::MS-MPPE-Send-Key += &reply:MS-MPPE-Send-Key[*] -> 0xa850facd73abb0940518b842f0da51a0 (8) &outer.session-state::MS-MPPE-Recv-Key += &reply:MS-MPPE-Recv-Key[*] -> 0x171b0a416b36492d6c7389dd24ca27a2 (8) &outer.session-state::EAP-Message += &reply:EAP-Message[*] -> 0x03b30004 (8) &outer.session-state::Message-Authenticator += &reply:Message-Authenticator[*] -> 0x00000000000000000000000000000000 (8) &outer.session-state::User-Name += &reply:User-Name[*] -> 'Test-A' (8) } # update = noop (8) update outer.session-state { (8) MS-MPPE-Encryption-Policy !* ANY (8) MS-MPPE-Encryption-Types !* ANY (8) MS-MPPE-Send-Key !* ANY (8) MS-MPPE-Recv-Key !* ANY (8) Message-Authenticator !* ANY (8) EAP-Message !* ANY (8) Proxy-State !* ANY (8) } # update outer.session-state = noop (8) } # post-auth = noop (8) } # server inner-tunnel (8) Virtual server sending reply (8) Tunnel-Type := VLAN (8) Tunnel-Medium-Type := IEEE-802 (8) Tunnel-Private-Group-Id := "1006" (8) MS-MPPE-Encryption-Policy = Encryption-Allowed (8) MS-MPPE-Encryption-Types = RC4-40or128-bit-Allowed (8) MS-MPPE-Send-Key = 0xa850facd73abb0940518b842f0da51a0 (8) MS-MPPE-Recv-Key = 0x171b0a416b36492d6c7389dd24ca27a2 (8) EAP-Message = 0x03b30004 (8) Message-Authenticator = 0x00000000000000000000000000000000 (8) User-Name = "Test-A" (8) eap_peap: Got tunneled reply code 2 (8) eap_peap: Tunnel-Type := VLAN (8) eap_peap: Tunnel-Medium-Type := IEEE-802 (8) eap_peap: Tunnel-Private-Group-Id := "1006" (8) eap_peap: MS-MPPE-Encryption-Policy = Encryption-Allowed (8) eap_peap: MS-MPPE-Encryption-Types = RC4-40or128-bit-Allowed (8) eap_peap: MS-MPPE-Send-Key = 0xa850facd73abb0940518b842f0da51a0 (8) eap_peap: MS-MPPE-Recv-Key = 0x171b0a416b36492d6c7389dd24ca27a2 (8) eap_peap: EAP-Message = 0x03b30004 (8) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (8) eap_peap: User-Name = "Test-A" (8) eap_peap: Got tunneled reply RADIUS code 2 (8) eap_peap: Tunnel-Type := VLAN (8) eap_peap: Tunnel-Medium-Type := IEEE-802 (8) eap_peap: Tunnel-Private-Group-Id := "1006" (8) eap_peap: MS-MPPE-Encryption-Policy = Encryption-Allowed (8) eap_peap: MS-MPPE-Encryption-Types = RC4-40or128-bit-Allowed (8) eap_peap: MS-MPPE-Send-Key = 0xa850facd73abb0940518b842f0da51a0 (8) eap_peap: MS-MPPE-Recv-Key = 0x171b0a416b36492d6c7389dd24ca27a2 (8) eap_peap: EAP-Message = 0x03b30004 (8) eap_peap: Message-Authenticator = 0x00000000000000000000000000000000 (8) eap_peap: User-Name = "Test-A" (8) eap_peap: Tunneled authentication was successful (8) eap_peap: SUCCESS (8) eap: Sending EAP Request (code 1) ID 180 length 43 (8) eap: EAP session adding &reply:State = 0xe87b0b92e0cf1203 (8) [eap] = handled (8) } # authenticate = handled (8) Using Post-Auth-Type Challenge (8) Post-Auth-Type sub-section not found. Ignoring. (8) # Executing group from file /etc/freeradius/sites-enabled/default (8) session-state: Saving cached attributes (8) Tunnel-Type += VLAN (8) Tunnel-Medium-Type += IEEE-802 (8) Tunnel-Private-Group-Id += "1006" (8) User-Name += "Test-A" (8) Sent Access-Challenge Id 18 from 172.17.28.67:1812 to 172.17.26.160:22492 length 0 (8) EAP-Message = 0x01b4002b1900170301002043738395e9d352c0a39ba3320922dcad449fea594061a41e682dd8d7c80a8183 (8) Message-Authenticator = 0x00000000000000000000000000000000 (8) State = 0xe87b0b92e0cf120391ed7d921e46c093 (8) Finished request Waking up in 4.3 seconds. (9) Received Access-Request Id 19 from 172.17.26.160:22492 to 172.17.28.67:1812 length 219 (9) User-Name = "Test-A" (9) NAS-Identifier = "44d9e7f96309" (9) NAS-Port = 0 (9) Called-Station-Id = "46-D9-E7-FA-63-09:SSID" (9) Calling-Station-Id = "60-A3-7D-2C-A2-19" (9) Framed-MTU = 1400 (9) NAS-Port-Type = Wireless-802.11 (9) Connect-Info = "CONNECT 0Mbps 802.11b" (9) EAP-Message = 0x02b4002b190017030100207ef889c7d2622aacff178bc6c0873a2cebf20cdc694dc5d78309a6ea8d241204 (9) State = 0xe87b0b92e0cf120391ed7d921e46c093 (9) Message-Authenticator = 0x6a57e6e906d2f5c42685efd242e96e00 (9) Restoring &session-state (9) &session-state:Tunnel-Type += VLAN (9) &session-state:Tunnel-Medium-Type += IEEE-802 (9) &session-state:Tunnel-Private-Group-Id += "1006" (9) &session-state:User-Name += "Test-A" (9) # Executing section authorize from file /etc/freeradius/sites-enabled/default (9) authorize { (9) policy filter_username { (9) if (&User-Name) { (9) if (&User-Name) -> TRUE (9) if (&User-Name) { (9) if (&User-Name =~ / /) { (9) if (&User-Name =~ / /) -> FALSE (9) if (&User-Name =~ /@[^@]*@/ ) { (9) if (&User-Name =~ /@[^@]*@/ ) -> FALSE (9) if (&User-Name =~ /\.\./ ) { (9) if (&User-Name =~ /\.\./ ) -> FALSE (9) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) { (9) if ((&User-Name =~ /@/) && (&User-Name !~ /(a)(.+)\.(.+)$/)) -> FALSE (9) if (&User-Name =~ /\.$/) { (9) if (&User-Name =~ /\.$/) -> FALSE (9) if (&User-Name =~ /(a)\./) { (9) if (&User-Name =~ /(a)\./) -> FALSE (9) } # if (&User-Name) = notfound (9) } # policy filter_username = notfound (9) [preprocess] = ok (9) [chap] = noop (9) [mschap] = noop (9) [digest] = noop (9) suffix: Checking for suffix after "@" (9) suffix: No '@' in User-Name = "Test-A", looking up realm NULL (9) suffix: No such realm "NULL" (9) [suffix] = noop (9) eap: Peer sent EAP Response (code 2) ID 180 length 43 (9) eap: Continuing tunnel setup (9) [eap] = ok (9) } # authorize = ok (9) Found Auth-Type = eap (9) # Executing group from file /etc/freeradius/sites-enabled/default (9) authenticate { (9) eap: Expiring EAP session with state 0xe87b0b92e0cf1203 (9) eap: Finished EAP session with state 0xe87b0b92e0cf1203 (9) eap: Previous EAP request found for state 0xe87b0b92e0cf1203, released from the list (9) eap: Peer sent packet with method EAP PEAP (25) (9) eap: Calling submodule eap_peap to process data (9) eap_peap: Continuing EAP-TLS (9) eap_peap: [eaptls verify] = ok (9) eap_peap: Done initial handshake (9) eap_peap: [eaptls process] = ok (9) eap_peap: Session established. Decoding tunneled attributes (9) eap_peap: PEAP state send tlv success (9) eap_peap: Received EAP-TLV response (9) eap_peap: Success (9) eap_peap: No information to cache: session caching will be disabled for session d8f7784bdabc1d0f47bfe939b6a8b6ecf01f2acae83ea6f7a5a1dcff7b869c5f (9) eap: Sending EAP Success (code 3) ID 180 length 4 (9) eap: Freeing handler (9) [eap] = ok (9) } # authenticate = ok (9) # Executing section post-auth from file /etc/freeradius/sites-enabled/default (9) post-auth { (9) update { (9) &reply::Tunnel-Type += &session-state:Tunnel-Type[*] -> VLAN (9) &reply::Tunnel-Medium-Type += &session-state:Tunnel-Medium-Type[*] -> IEEE-802 (9) &reply::Tunnel-Private-Group-Id += &session-state:Tunnel-Private-Group-Id[*] -> '1006' (9) &reply::User-Name += &session-state:User-Name[*] -> 'Test-A' (9) } # update = noop (9) [exec] = noop (9) policy remove_reply_message_if_eap { (9) if (&reply:EAP-Message && &reply:Reply-Message) { (9) if (&reply:EAP-Message && &reply:Reply-Message) -> FALSE (9) else { (9) [noop] = noop (9) } # else = noop (9) } # policy remove_reply_message_if_eap = noop (9) } # post-auth = noop (9) Sent Access-Accept Id 19 from 172.17.28.67:1812 to 172.17.26.160:22492 length 0 (9) MS-MPPE-Recv-Key = 0x494d4c1a1c11447875b167dffa41b23d04f888ca430351f2e79ae0a2a5d66cf4 (9) MS-MPPE-Send-Key = 0x76c071086f956bbf8bbd0e5aed6f552fa1df2caec39e8ea47448042dbad7ec73 (9) EAP-Message = 0x03b40004 (9) Message-Authenticator = 0x00000000000000000000000000000000 (9) User-Name = "Test-A" (9) Tunnel-Type += VLAN (9) Tunnel-Medium-Type += IEEE-802 (9) Tunnel-Private-Group-Id += "1006" (9) User-Name += "Test-A" (9) Finished request

5 4

Radmin - no home server stats
by John Horne 27 Jan '17

27 Jan '17

Hello, We are running freeradius 3.0.4 on CentOS 7. We noticed that the radmin command was showing no stats for our home servers. That is they showed '0' for the requests, responses, etc. For example: ===================== radmin -e 'stats home_server auth' requests 0 responses 0 accepts 0 rejects 0 challenges 0 dup 0 invalid 0 malformed 0 bad_authenticator 0 dropped 0 unknown_types 0 timeouts 1909 last_packet 1485533480 elapsed.1us 0 elapsed.10us 0 elapsed.100us 0 elapsed.1ms 0 elapsed.10ms 0 elapsed.100ms 0 elapsed.1s 0 elapsed.10s 0 ===================== The server is relatively busy, so there should certainly be some stats. It has not been rebooted recently - which I assume would zero the stats. Anyone any suggestions about this? Thanks, John. -- John Horne Tel: +44 (0)1752 587287 Plymouth University, UK ________________________________ [http://www.plymouth.ac.uk/images/email_footer.gif]<http://www.plymouth.ac.uk/worldclass> This email and any files with it are confidential and intended solely for the use of the recipient to whom it is addressed. If you are not the intended recipient then copying, distribution or other use of the information contained is strictly prohibited and you should not rely on it. If you have received this email in error please let the sender know immediately and delete it from your system(s). Internet emails are not necessarily secure. While we take every care, Plymouth University accepts no responsibility for viruses and it is your responsibility to scan emails and their attachments. Plymouth University does not accept responsibility for any changes made after it was sent. Nothing in this email or its attachments constitutes an order for goods or services unless accompanied by an official order form.

4 8

MS-CHAP modules
by Chris Howley 27 Jan '17

27 Jan '17

I just installed 3.0.12 and I'm testing the default and inner-server virtual servers. Would someone tell me/point me to the documentation that shows me how I would call different MS-CHAP modules in the inner-tunnel virtual server. Thanks, Chris Howley

3 2

accounting problem
by Lorenzo Cipriani 26 Jan '17

26 Jan '17

I installed freeradius 3.0.12 version from source code, I enabled details and sql modules, on accounting section. But don't see any log in radacct folder and in radacct table. Is it a version problem? Thanks

2 1

max_requests
by iQalalwa 26 Jan '17

26 Jan '17

Dear Sir, I have freeradius 2.2 and i have 27, 000 clients, I want to ask what is the suitable max_requests in radius configuration? Thanks

2 3