Hi,
I would like to allow host access to the network according to these
restrictions (I am listing only those that require a RADIUS server):
1) wireless clients that connect to a specific SSID are required to
either use EAP-TLS or PEAP. If they pass the authorization and
authentication they will be dynamically assigned to vlan 112 (base on
a local SQL lookup of their MAC addresses). Rejected otherwise.
2) wired clients:
a) If they support dot1x, use either EAP-TLS or PEAP and pass then
they will be dynamically assigned to vlan 20 (base on a local SQL
lookup of their MAC addresses).
b) If dot1x fails try MAC Authentication Bypass. The MAC address
received by the Freeradius server will be looked up in a local DB, and
a VLAN ID will be dynamically assigned accordingly (different vlan IDs
except '1').
c) If the MAC address involved in MAB is not found in the local DB
then allow access but dynamically assign another vlan ID (eg. 1).
I have a FreeRADIUS server and a mix of Cisco and D-Link switches (but
I'll be focusing on Cisco because I don't think the D-Link models I
have support MAB).
Step 1 (wireless clients) has been working fine for years now.
I managed to get step 2 working, but then step 1 fails.
The configuration is quite long so I hope no one minds if I paste here
some sections.
Here is the "working" configuration for step 1 (for testing purposes
and to simplify debugging I'm just assigning vlan ID 112 when using
EAP and vlan ID 1 when not).
File 'sites-enabled/default' contains:
server default {
listen {
type = auth
ipaddr = *
port = 0
limit {
max_connections = 16
lifetime = 0
idle_timeout = 30
}
}
listen {
ipaddr = *
port = 0
type = acct
limit {
}
}
listen {
type = auth
ipv6addr = ::
port = 0
limit {
max_connections = 16
lifetime = 0
idle_timeout = 30
}
}
listen {
ipv6addr = ::
port = 0
type = acct
limit {
}
}
authorize {
custom_split_username_nai
filter_username
preprocess
custom_filter_default
suffix
ntdomain
-ldap
expiration
logintime
}
authenticate {
Auth-Type PAP {
pap
}
Auth-Type CHAP {
chap
}
Auth-Type MS-CHAP {
mschap
}
eap
}
preacct {
preprocess
acct_unique
suffix
}
accounting {
unix
exec
attr_filter.accounting_response
}
session {
}
post-auth {
update {
&reply: += &session-state:
}
linelog
exec
remove_reply_message_if_eap
Post-Auth-Type REJECT {
linelog
attr_filter.access_reject
eap
remove_reply_message_if_eap
}
Post-Auth-Type Challenge {
}
if (EAP-Message) {
update reply {
&Tunnel-Type := VLAN
&Tunnel-Medium-Type := IEEE-802
&Tunnel-Private-Group-Id := 112
# &Auth-Type := Accept
}
} else {
update reply {
&Tunnel-Type := VLAN
&Tunnel-Medium-Type := IEEE-802
&Tunnel-Private-Group-Id := 1
# &Auth-Type := Accept
}
}
}
pre-proxy {
}
post-proxy {
eap
}
}
---
In file policy.d/filter custom_filter_default looks up MAC addresses
in local DB eventually denying some requests.
A debug log of a working authentication (step 1) would look something like this:
(32) Received Access-Request Id 200 from 192.168.216.22:43597 to
10.215.144.91:1812 length 435
(32) User-Name = "host/HM2214.domain.local"
(32) NAS-Identifier = "b4fbe475aed9"
(32) Called-Station-Id = "B4-FB-E4-75-AE-D9:HM private access"
(32) NAS-Port-Type = Wireless-802.11
(32) Service-Type = Framed-User
(32) Calling-Station-Id = "8C-55-4A-D5-73-57"
(32) Connect-Info = "CONNECT 0Mbps 802.11b"
(32) Acct-Session-Id = "E70814F5EF081437"
(32) Acct-Multi-Session-Id = "355A9CEC86878217"
(32) WLAN-Pairwise-Cipher = 1027076
(32) WLAN-Group-Cipher = 1027076
(32) WLAN-AKM-Suite = 1027073
(32) Framed-MTU = 1400
(32) EAP-Message =
0x025400ac0d80000000a2160303009d0100009903036317801de99d7d69b9fec9eb8e49887f7c0eb4abedee360ab1fc236b4de4a05800002ac02cc02bc030c02f009f009ec024c023c028c027c00ac009c014c013009d009c003d003c0035002f000a01000046000500050100000000000a00080006001d00170018000b00020100000d001a00180804080508060401050102010403050302030202060106030023000000170000ff01000100
(32) State = 0x0081417701d54caa876904a5f97342cd
(32) Message-Authenticator = 0xaf1a468d4f13396bec05eaa4670f2bdc
[...]
(32) authorize {
[...]
[ntdomain] = noop
(32) [expiration] = noop
(32) [logintime] = noop
(32) } # authorize = updated
(32) Found Auth-Type = eap
(32) # Executing group from file /etc/raddb/sites-enabled/default
(32) authenticate {
(32) eap: Expiring EAP session with state 0x0081417701d54caa
(32) eap: Finished EAP session with state 0x0081417701d54caa
(32) eap: Previous EAP request found for state 0x0081417701d54caa,
released from the list
(32) eap: Peer sent packet with method EAP TLS (13)
(32) eap: Calling submodule eap_tls to process data
(32) eap_tls: (TLS) EAP Peer says that the final record size will be 162 bytes
(32) eap_tls: (TLS) EAP Got all data (162 bytes)
(32) eap_tls: (TLS) Handshake state - before SSL initialization (0)
(32) eap_tls: (TLS) Handshake state - Server before SSL initialization (0)
(32) eap_tls: (TLS) Handshake state - Server before SSL initialization (0)
(32) eap_tls: (TLS) recv TLS 1.3 Handshake, ClientHello
(32) eap_tls: (TLS) Handshake state - Server SSLv3/TLS read client hello (20)
(32) eap_tls: (TLS) send TLS 1.2 Handshake, ServerHello
(32) eap_tls: (TLS) Handshake state - Server SSLv3/TLS write server hello (22)
(32) eap_tls: (TLS) send TLS 1.2 Handshake, Certificate
(32) eap_tls: (TLS) Handshake state - Server SSLv3/TLS write certificate (23)
(32) eap_tls: (TLS) send TLS 1.2 Handshake, ServerKeyExchange
(32) eap_tls: (TLS) Handshake state - Server SSLv3/TLS write key exchange (24)
(32) eap_tls: (TLS) send TLS 1.2 Handshake, CertificateRequest
(32) eap_tls: (TLS) Handshake state - Server SSLv3/TLS write
certificate request (25)
(32) eap_tls: (TLS) send TLS 1.2 Handshake, ServerHelloDone
(32) eap_tls: (TLS) Handshake state - Server SSLv3/TLS write server done (26)
(32) eap_tls: (TLS) Server : Need to read more data: SSLv3/TLS write server done
(32) eap_tls: (TLS) In Handshake Phase
(32) eap: Sending EAP Request (code 1) ID 85 length 1004
(32) eap: EAP session adding &reply:State = 0x0081417702d44caa
(32) [eap] = handled
(32) } # authenticate = handled
(32) Using Post-Auth-Type Challenge
(32) # Executing group from file /etc/raddb/sites-enabled/default
(32) Challenge { ... } # empty sub-section is ignored
(32) session-state: Saving cached attributes
(32) Framed-MTU = 994
(32) Sent Access-Challenge Id 200 from 10.215.144.91:1812 to
192.168.216.22:43597 length 0
[...]
(37) authenticate {
(37) eap: Expiring EAP session with state 0x0081417706d84caa
(37) eap: Finished EAP session with state 0x0081417706d84caa
(37) eap: Previous EAP request found for state 0x0081417706d84caa,
released from the list
(37) eap: Peer sent packet with method EAP TLS (13)
(37) eap: Calling submodule eap_tls to process data
(37) eap_tls: (TLS) EAP Got final fragment (1012 bytes)
(37) eap_tls: (TLS) EAP Done initial handshake
(37) eap_tls: (TLS) Handshake state - Server SSLv3/TLS write server done (26)
(37) eap_tls: (TLS) recv TLS 1.2 Handshake, Certificate
(37) eap_tls: (TLS) Creating attributes from TLS-Client-Cert-Serial certificate
(37) eap_tls: (TLS) Creating attributes from server certificate
(37) eap_tls: TLS-Cert-Serial := "5b0000000f6866b08df40ccce300010000000f"
(37) eap_tls: TLS-Cert-Expiration := "320829094522Z"
(37) eap_tls: TLS-Cert-Valid-Since := "220901094522Z"
(37) eap_tls: TLS-Cert-Subject := "/DC=local/DC=domain/CN=SUBCAHM"
(37) eap_tls: TLS-Cert-Issuer := "/DC=local/DC=domain/CN=CAHM"
(37) eap_tls: TLS-Cert-Common-Name := "SUBCAHM"
(37) eap_tls: (TLS) Creating attributes from client certificate
(37) eap_tls: TLS-Client-Cert-Serial :=
"3100002953a699132464a0c6c4000800002953"
(37) eap_tls: TLS-Client-Cert-Expiration := "230906155017Z"
(37) eap_tls: TLS-Client-Cert-Valid-Since := "220906155017Z"
(37) eap_tls: TLS-Client-Cert-Subject := "/CN=HM2214.domain.local"
(37) eap_tls: TLS-Client-Cert-Issuer := "/DC=local/DC=domain/CN=SUBCAHM"
(37) eap_tls: TLS-Client-Cert-Common-Name := "HM2214.domain.local"
(37) eap_tls: TLS-Client-Cert-Subject-Alt-Name-Dns := "HM2214.domain.local"
(37) eap_tls: TLS-Client-Cert-X509v3-Extended-Key-Usage += "TLS Web
Client Authentication, TLS Web Server Authentication"
(37) eap_tls: TLS-Client-Cert-X509v3-Subject-Key-Identifier +=
"38:AE:B8:45:E3:FF:5F:E8:6B:E9:F8:CA:8A:DA:0C:C7:55:63:69:71"
(37) eap_tls: TLS-Client-Cert-X509v3-Authority-Key-Identifier +=
"keyid:2B:A9:FC:BD:BA:C9:E4:C0:E2:55:23:36:EB:96:FD:F0:03:CC:53:2D\n"
(37) eap_tls: TLS-Client-Cert-X509v3-Extended-Key-Usage-OID +=
"1.3.6.1.5.5.7.3.2"
(37) eap_tls: TLS-Client-Cert-X509v3-Extended-Key-Usage-OID +=
"1.3.6.1.5.5.7.3.1"
(37) eap_tls: (TLS) Handshake state - Server SSLv3/TLS read client
certificate (27)
(37) eap_tls: (TLS) recv TLS 1.2 Handshake, ClientKeyExchange
(37) eap_tls: (TLS) Handshake state - Server SSLv3/TLS read client key
exchange (28)
(37) eap_tls: (TLS) recv TLS 1.2 Handshake, CertificateVerify
(37) eap_tls: (TLS) Handshake state - Server SSLv3/TLS read
certificate verify (29)
(37) eap_tls: (TLS) Handshake state - Server SSLv3/TLS read change
cipher spec (31)
(37) eap_tls: (TLS) recv TLS 1.2 Handshake, Finished
(37) eap_tls: (TLS) Handshake state - Server SSLv3/TLS read finished (32)
(37) eap_tls: (TLS) send TLS 1.2 ChangeCipherSpec
(37) eap_tls: (TLS) Handshake state - Server SSLv3/TLS write change
cipher spec (35)
(37) eap_tls: (TLS) send TLS 1.2 Handshake, Finished
(37) eap_tls: (TLS) Handshake state - Server SSLv3/TLS write finished (36)
(37) eap_tls: (TLS) Handshake state - SSL negotiation finished successfully (1)
(37) eap_tls: (TLS) Connection Established
(37) eap_tls: TLS-Session-Cipher-Suite = "ECDHE-RSA-AES256-GCM-SHA384"
(37) eap_tls: TLS-Session-Version = "TLS 1.2"
(37) eap: Sending EAP Request (code 1) ID 90 length 61
(37) eap: EAP session adding &reply:State = 0x0081417707db4caa
(37) [eap] = handled
(37) } # authenticate = handled
(37) Using Post-Auth-Type Challenge
(37) # Executing group from file /etc/raddb/sites-enabled/default
(37) Challenge { ... } # empty sub-section is ignored
(37) session-state: Saving cached attributes
(37) Framed-MTU = 994
(37) TLS-Session-Cipher-Suite = "ECDHE-RSA-AES256-GCM-SHA384"
(37) TLS-Session-Version = "TLS 1.2"
(37) Sent Access-Challenge Id 205 from 10.215.144.91:1812 to
192.168.216.22:43597 length 0
(37) EAP-Message =
0x015a003d0d80000000331403030001011603030028c62d4b915fa17f780d1eeed1c8df2666d86f908e5ffa52fb0f687cd05e9a61940f477283e89dfc87
(37) Message-Authenticator = 0x00000000000000000000000000000000
(37) State = 0x0081417707db4caa876904a5f97342cd
(37) Finished request
Waking up in 4.6 seconds.
(38) Received Access-Request Id 206 from 192.168.216.22:43597 to
10.215.144.91:1812 length 269
(38) User-Name = "host/HM2214.domain.local"
[...]
(38) authenticate {
(38) eap: Expiring EAP session with state 0x0081417707db4caa
(38) eap: Finished EAP session with state 0x0081417707db4caa
(38) eap: Previous EAP request found for state 0x0081417707db4caa,
released from the list
(38) eap: Peer sent packet with method EAP TLS (13)
(38) eap: Calling submodule eap_tls to process data
(38) eap_tls: (TLS) Peer ACKed our handshake fragment. handshake is finished
(38) eap: Sending EAP Success (code 3) ID 90 length 4
(38) eap: Freeing handler
(38) [eap] = ok
(38) } # authenticate = ok
(38) # Executing section post-auth from file /etc/raddb/sites-enabled/default
(38) post-auth {
(38) update {
(38) &reply::Framed-MTU += &session-state:Framed-MTU[*] -> 994
(38) &reply::TLS-Session-Cipher-Suite +=
&session-state:TLS-Session-Cipher-Suite[*] ->
'ECDHE-RSA-AES256-GCM-SHA384'
(38) &reply::TLS-Session-Version +=
&session-state:TLS-Session-Version[*] -> 'TLS 1.2'
(38) } # update = noop
(38) linelog: EXPAND messages.%{%{reply:Packet-Type}:-default}
(38) linelog: --> messages.Access-Accept
(38) linelog: EXPAND Accepted user: %{User-Name}
(38) linelog: --> Accepted user: host/HM2214.domain.local
(38) linelog: EXPAND /var/log/radius/linelog
(38) linelog: --> /var/log/radius/linelog
(38) [linelog] = ok
(38) [exec] = noop
(38) policy remove_reply_message_if_eap {
(38) if (&reply:EAP-Message && &reply:Reply-Message) {
(38) if (&reply:EAP-Message && &reply:Reply-Message) -> FALSE
(38) else {
(38) [noop] = noop
(38) } # else = noop
(38) } # policy remove_reply_message_if_eap = noop
(38) if (EAP-Message) {
(38) if (EAP-Message) -> TRUE
(38) if (EAP-Message) {
(38) update reply {
(38) &Tunnel-Type := VLAN
(38) &Tunnel-Medium-Type := IEEE-802
(38) &Tunnel-Private-Group-Id := 112
(38) } # update reply = noop
(38) } # if (EAP-Message) = noop
(38) } # else = noop
(38) } # post-auth = ok
(38) Login OK: [host/HM2214.domain.local] (from client UH3B3 port 0
cli 8C-55-4A-D5-73-57)
(38) Sent Access-Accept Id 206 from 10.215.144.91:1812 to
192.168.216.22:43597 length 0
(38) MS-MPPE-Recv-Key =
0xf4306c74bb325ce7db5a69f321f82830cb28530f48748c69cf1df45cf32f8994
(38) MS-MPPE-Send-Key =
0xd246e7a33f6701cec10c067ab22350bf04080357151e849b8c6038a0e3762cf4
(38) EAP-Message = 0x035a0004
(38) Message-Authenticator = 0x00000000000000000000000000000000
(38) User-Name = "host/HM2214.domain.local"
(38) Framed-MTU += 994
(38) Tunnel-Type := VLAN
(38) Tunnel-Medium-Type := IEEE-802
(38) Tunnel-Private-Group-Id := "112"
(38) Finished request
---
So the host HM2214.domain.local is now within vlan 112 and has the
expected network access rights.
I then tried to modify the Freeradius configuration to allow wired
hosts access to the network. Again, to simplify things at first I did
not connect a client with dot1x - I just wanted to use MAB. Thus the
Cisco switch sends the client's MAC address as the "user name".
This is part of a debug log of a successful login of a wired host.
(36) Received Access-Request Id 139 from 172.28.175.244:1645 to
172.28.175.254:1812 length 261
(36) User-Name = "c4346b67d37f"
(36) User-Password = "c4346b67d37f"
(36) Service-Type = Call-Check
(36) Cisco-AVPair = "service-type=Call Check"
(36) Framed-MTU = 1500
(36) Called-Station-Id = "00-27-90-6C-BA-8D"
(36) Calling-Station-Id = "C4-34-6B-67-D3-7F"
(36) Message-Authenticator = 0x34433f3a86e93db1665f511096654022
(36) Cisco-AVPair = "audit-session-id=AC1CAFF40000001C2427594E"
(36) Cisco-AVPair = "method=mab"
(36) NAS-IP-Address = 172.28.175.244
(36) NAS-Port-Id = "GigabitEthernet1/0/13"
(36) NAS-Port-Type = Ethernet
(36) NAS-Port = 50113
(36) # Executing section authorize from file /etc/raddb/sites-enabled/default
(36) authorize {
[...]
(36) eap: No EAP-Message, not doing EAP
(36) [eap] = noop
[...]
(36) [ntdomain] = noop
(36) files: users: Matched entry c4346b67d37f at line 207
(36) [files] = ok
(36) [expiration] = noop
(36) [logintime] = noop
(36) [pap] = updated
(36) } # authorize = updated
(36) Found Auth-Type = PAP
(36) # Executing group from file /etc/raddb/sites-enabled/default
(36) Auth-Type PAP {
(36) pap: Login attempt with password
(36) pap: Comparing with "known good" Cleartext-Password
(36) pap: User authenticated successfully
(36) [pap] = ok
(36) } # Auth-Type PAP = ok
(36) # Executing section post-auth from file /etc/raddb/sites-enabled/default
(36) post-auth {
(36) update {
(36) No attributes updated for RHS &session-state:
(36) } # update = noop
(36) linelog: EXPAND messages.%{%{reply:Packet-Type}:-default}
(36) linelog: --> messages.Access-Accept
(36) linelog: EXPAND Accepted user: %{User-Name}
(36) linelog: --> Accepted user: c4346b67d37f
(36) linelog: EXPAND /var/log/radius/linelog
(36) linelog: --> /var/log/radius/linelog
(36) [linelog] = ok
(36) [exec] = noop
(36) policy remove_reply_message_if_eap {
(36) if (&reply:EAP-Message && &reply:Reply-Message) {
(36) if (&reply:EAP-Message && &reply:Reply-Message) -> FALSE
(36) else {
(36) [noop] = noop
(36) } # else = noop
(36) } # policy remove_reply_message_if_eap = noop
(36) if (EAP-Message) {
(36) if (EAP-Message) -> FALSE
(36) else {
(36) update reply {
(36) &Tunnel-Type := VLAN
(36) &Tunnel-Medium-Type := IEEE-802
(36) &Tunnel-Private-Group-Id := 1
(36) } # update reply = noop
(36) } # else = noop
(36) } # post-auth = ok
(36) Login OK: [c4346b67d37f] (from client D2423 port 50113 cli
C4-34-6B-67-D3-7F)
(36) Sent Access-Accept Id 139 from 172.28.175.254:1812 to
172.28.175.244:1645 length 0
(36) Tunnel-Type := VLAN
(36) Tunnel-Medium-Type := IEEE-802
(36) Tunnel-Private-Group-Id := "1"
(36) Tunnel-Preference = 0
(36) Finished request
In order to get this I modified 'sites-enabled/default' to include
'files' in the 'authorize' section. I also had to add the following in
the users file:
DEFAULT Auth-Type := Accept
That's because I was hoping to accomplish what is stated in Step 2
(c), ie. allow "any" MAC address but assign a different vlan ID.
With this configuration wired hosts access "as expected", but wireless
hosts with EAP-TLS fail to have access to the network even though the
freeradisu debug log reports a "Login OK" line. The EAP messages are
not seen in the log so it seems they're being by-passed.
I'd like to give more information, but this e-mail is long already --
maybe even too long.
What could I try from here?
Regards,
Vieri
